R. Shanthini 19 May 2010 1 Content of Lectures 10 to 12: Heat transfer: Mathematical problems on...
-
Upload
rhoda-fletcher -
Category
Documents
-
view
220 -
download
3
Transcript of R. Shanthini 19 May 2010 1 Content of Lectures 10 to 12: Heat transfer: Mathematical problems on...
R. Shanthini 19 May 2010
1
Content of Lectures 10 to 12:
Heat transfer: • Mathematical problems on heat transfer
PM3125: Lectures 10 to 12
R. Shanthini 19 May 2010
2
Heat Exchanger in the industry
Shell-and-Tube Heat Exchanger
R. Shanthini 19 May 2010
3
Heat Exchanger in the industry
Shell-and-Tube Heat Exchanger
R. Shanthini 19 May 2010
4
Heat Exchanger in the industry
Shell-and-Tube Heat Exchanger
R. Shanthini 19 May 2010
5
Heat Exchanger in the industry
Shell
Tubes
Baffle
Shell-and-Tube Heat Exchanger
R. Shanthini 19 May 2010
6
Heat Exchanger in the industry
Shell-and-Tube Heat Exchanger
R. Shanthini 19 May 2010
7
Heat Exchanger Analysis
Tc,in
Tc,out
Th,in
Th,out
. .Q = mc cc (Tc,out – Tc,in) = mh ch (Th,in – Th,out)
.
R. Shanthini 19 May 2010
8
Tc,in
Th,out
Th,in
Tc,out
Tc,in
Tc,out
Th,in
Th,out
Parallel-flow heat exchanger
high heat transfer
low heat transfer
Heat Exchanger Analysis
R. Shanthini 19 May 2010
9
Tc,in
Th,out
Th,in
Tc,out
a b
Q = U A ΔTLM .
where ΔTLM = ΔTa - ΔTb
ln(ΔTa / ΔTb)is the log mean temperature difference (LMTD)
ΔTa ΔTb
Parallel-flow heat exchanger
Heat Exchanger Analysis – LMTD method
R. Shanthini 19 May 2010
10
Tc,out
Tc,in
Th,in
Th,out
. .Q = mc cc (Tc,out – Tc,in) = mh ch (Th,in – Th,out)
.
Counter-flow heat exchanger
Heat Exchanger Analysis
R. Shanthini 19 May 2010
11
Tc,in
Tc,out
Th,in
Th,out
Th,in
Th,out
Counter-flow heat exchanger
Tc,in
Tc,out
Heat Exchanger Analysis
R. Shanthini 19 May 2010
12
a b
Q = U A ΔTLM .
where ΔTLM = ΔTa - ΔTb
ln(ΔTa / ΔTb)is the log mean temperature difference (LMTD)
ΔTa
ΔTb
Counter-flow heat exchanger
Tc,in
Tc,out
Th,in
Th,out
Heat Exchanger Analysis – LMTD method
R. Shanthini 19 May 2010
13
An exhaust pipe, 75 mm outside diameter, is cooled by surrounding it by an annular space containing water.
The hot gases enters the exhaust pipe at 350oC, gas flow rate being 200 kg/h, mean specific heat capacity at constant pressure 1.13 kJ/kg K, and comes out at 100oC.
Water enters from the mains at 25oC, flow rate 1400 kg/h, mean specific heat capacity 4.19 kJ/kg K.
The heat transfer coefficient for gases and water may be taken as 0.3 and 1.5 kW/m2 K and pipe thickness may be taken as negligible.
Calculate the required pipe length for (i) parallel flow, and for (ii) counter flow.
Heat Exchanger Design – LMTD method
R. Shanthini 19 May 2010
14
Solution:
. .Q = mc cc (Tc,out – Tc,in) = mh ch (Th,in – Th,out)
.
(1400 kg/hr) (4.19 kJ/kg K) (Tc,out – 25)oC
= (200 kg/hr) (1.13 kJ/kg K) (350 – 100)oC
The temperature of water at the outlet = Tc,out = 34.63oC.
Heat Exchanger Design – LMTD method
R. Shanthini 19 May 2010
15
(i) Parallel flow:
ΔTa = 350 – 25 = 325oC
ΔTb = 100 – 34.63 = 65.37oC
ΔTLM = ΔTa - ΔTb
ln(ΔTa / ΔTb)
325 – 65.37
ln(325 / 65.37)= = 162oC
Q = U A ΔTLM .
= (UA) 162oC
What is UA?
Heat Exchanger Design – LMTD method
Solution continued:
R. Shanthini 19 May 2010
16
1/U = 1/hwater + 1/hgases
= 1/1.5 + 1/0.3 = 4 (kW/m2 K)-1
Therefore, U = 0.25 kW/m2 K
A = π (outer diameter) (L) = π (0.075 m) (L m)
Q .
= (UA) 162oC
What is Q?
= (0.25) π (0.075) L (162) kW
.
Heat Exchanger Design – LMTD method
Solution continued:
R. Shanthini 19 May 2010
17
Q .
= (UA) 162oC = (0.25) π (0.075) L (162) kW
. .Q = mc cc (Tc,out – Tc,in) = mh ch (Th,in – Th,out)
.
= (200 kg/h) (1.13 kJ/kg K) (350 – 100)oC = 15.69 kW
Substituting the above in
we getL = 1.64 m
Heat Exchanger Design – LMTD method
Solution continued:
R. Shanthini 19 May 2010
18
(ii) Counter flow:
ΔTa = 350 – 34.63 = 315.37oC
ΔTb = 100 – 25 = 75oC
ΔTa - ΔTb
ln(ΔTa / ΔTb)
315.37 – 75
ln(315.37 / 75)= = 167.35oC
.= (UA) 167.35oC
Q = 15.69 kW; U = 0.25 kW/m2 K ;.
A = π (0.075) L m2
Therefore, L = 1.59 m
Heat Exchanger Design – LMTD method
Q = U A ΔTLM
ΔTLM =
Solution continued:
R. Shanthini 19 May 2010
19
Other Heat Exchanger Types
Cross-flow heat exchanger with both fluids unmixed
The direction of fluids are perpendicular to each other.
In calculating the required surface area for this heat exchanger using LMTD method, a correction factor is applied on the LMTD.
It lies between the required surface area for counter-flow and parallel-flow heat exchangers.
R. Shanthini 19 May 2010
20
Cross-flow Heat Exchanger Analysis
Q = U A ΔTLM .
ΔTLM = F ΔTLM, counter flow
R. Shanthini 19 May 2010
21
In calculating the required surface area for this heat exchanger using LMTD method, a correction factor is applied on the LMTD.
Other Heat Exchanger Types
One shell pass and two tube passes
T1
T2
t2
t1
t2
t1
T1
T2
R. Shanthini 19 May 2010
22
Two shell passes and two tube passes
Th,inTc,in
Th,out
Tc,out
Other Heat Exchanger Types
In calculating the required surface area for this heat exchanger using LMTD method, a correction factor is applied on the LMTD.
R. Shanthini 19 May 2010
23
Multi-pass Heat Exchanger Analysis
See lecture notes provided separately.
R. Shanthini 19 May 2010
24
Batch Sterilization (method of heating):
Steamheating
Electricalheating
Direct steam sparging
R. Shanthini 19 May 2010
25
For batch heating with constant rate heat flow:
M c (T - T0) q t =
M - mass of the medium
T0 - initial temperature of the medium
T - final temperature of the medium
c - specific heat of the medium
q - rate of heat transfer from the electrical coil to the medium
t - duration of electrical heating
Electricalheating
Total heat lost by the coil to the medium
= heat gained by the medium
.
.
R. Shanthini 19 May 2010
26
Direct steam sparging = (M + ms t) c (T – T0)
M - initial mass of the raw medium
T0 - initial temperature of the raw medium
ms - steam mass flow rate
t - duration of steam sparging
H - enthalpy of steam relative to the enthalpy at the initial temperature of the raw medium (T0)
T - final temperature of the mixture
c - specific heat of medium and water
For batch heating by direct steam sparging:
.
(ms t) (H + cT0).
+ M c T0 = (M + mst) c T.
ms t H. .
R. Shanthini 19 May 2010
27
For batch heating with isothermal heat source:
M - mass of the medium
T0 - initial temperature of the medium
TH - temperature of heat source (steam)
T - final temperature of the medium
c - specific heat of the medium
t - duration of steam heating
U - overall heat transfer coefficient
A - heat transfer area
Steamheating
U A t = M c ln
Could you prove the above?
T0 - TH ( ) T - TH
R. Shanthini 19 May 2010
28
For batch heating with isothermal heat source:
Steamheating
T = TH + (T0 - TH) exp - U A tc M ( )
U A t = M c lnT0 - TH ( ) T - TH
R. Shanthini 19 May 2010
29
Example of batch heating by direct steam sparging:
A fermentor containing 40 m3 medium at 25oC is going to be sterilized by direct injection of saturated steam. The steam at 350 kPa absolute pressure is injected with a flow rate of 5000 kg/hr, which will be stopped when the medium temperature reaches 122oC. Determine the time taken to heat the medium.
Additional data required:
Enthalpy of saturated steam at 350 kPa = ??
Enthalpy of water at 25oC = ??
The heat capacity of the medium 4.187 kJ/kg.K
The density of the medium are 4.187 kJ/kg.K and 1000 kg/m3, respectively.)
R. Shanthini 19 May 2010
30
Example of batch heating by direct steam sparging:
A fermentor containing 40 m3 medium at 25oC is going to be sterilized by direct injection of saturated steam. The steam at 350 kPa absolute pressure is injected with a flow rate of 5000 kg/hr, which will be stopped when the medium temperature reaches 122oC. Determine the time taken to heat the medium.
Additional data: The enthalpy of saturated steam at 350 kPa and water at 25oC are 2732 and 105 kJ/kg, respectively. The heat capacity and density of the medium are 4.187 kJ/kg.K and 1000 kg/m3, respectively.
Solution:
= (M + ms t) c (T – T0)ms t H. .
Use the equation below:
R. Shanthini 19 May 2010
31
(5000 kg/hr) (th) (2732-105) kJ/kg
= [(40 m3)(1000 kg/m3) + (5000 kg/hr)(th)](4.187 kJ/kg.K)(122-25)K
(5000 th) (2627) kJ = [40000 + 5000 t](4.187)(97)kJ
Taking the heating time (th) to be in hr, we get
(5000 th) [2627 – 4.187 x 97] = 40000 x 4.187 x 97
th = 1.463 hr
= (M + ms t) c (T – T0)ms t H. .
Therefore, the time taken to heat the medium is 1.463 hours.
R. Shanthini 19 May 2010
32
Example of batch heating with isothermal heat source:
A fermentor containing 40 m3 medium at 25oC is going to be sterilized by an isothermal heat source, which is saturated steam at 350 kPa absolute pressure. Heating will be stopped when the medium temperature reaches 122oC. Determine the time taken to heat the medium.
Additional data: The saturated temperature of steam at 350 kPa is 138.9oC. The heat capacity and density of the medium are 4.187 kJ/kg.K and 1000 kg/m3, respectively. U = 2500 kJ/hr.m2.K and A = 40 m2
Solution:
Use the equation below:
U A t = M c lnT0 - TH ( ) T - TH
R. Shanthini 19 May 2010
33
U A t = M c lnT0 - TH ( ) T - TH
Taking the heating time (th) to be in hr, we get
(2500 kJ/hr.m2.K) (40 m2) (tc)
= (40 m3) (1000 kg/m3) (4.187 kJ/kg.K) ln[(25-138.9)/(122-138.9)]
(2500 kJ/K) (40) (th) = (40) (1000) (4.187 kJ/K) ln[113.9/16.9]
(2500 kJ/K) (40) (th) = (40) (1000) (4.187 kJ/K) (1.908)
th = 3.1955 hr
Therefore, the time taken to heat the medium is 3.1955 hours.
R. Shanthini 19 May 2010
34
Explain why heating with isothermal heat source takes twice the time taken by heating with steam sparging, even though we used the same steam.
R. Shanthini 19 May 2010
35
2) Briefly discuss the applications of the following laws.
(a) Fourier’s law [2.5 marks](b) Newton’s law of cooling [2.5
marks](c) Stefan–Boltzmann Law [2.5
marks](d) Fick’s law [2.5
marks]
Questions from PM3125 / Feb 2010 past paper
1)(a) What are the major differences between diffusion and
convection? [5 marks](b) What are the major differences among conduction, convection
and radiation? [5 marks]
R. Shanthini 19 May 2010
36
8) A steel pipeline (inside diameter = 52.50 mm; outside diameter = 60.32 mm) contains saturated steam at 121.1oC. The line is insulated with 25.4 mm of asbestos. Assume that the inside surface temperature of the metal wall is at 121.1oC and the outer surface of the insulation is at 26.7oC. Taking the average value of ksteel as 45 W/m.K and that of
kasbestos as 0.182 W/m.K, calculate the following:
(a) Heat loss for 30.5 m of pipe length. [10 marks]
(b) Mass (in kg) of steam condensed per hour in the pipe due to the heat loss. [10 marks]
Additional data given on the next slide:
Questions from PM3125 / Feb 2010 past paper
R. Shanthini 19 May 2010
37
Additional Data:
i) Heat transfer rate through the pipe wall is given by,
asbestos
23
steel
12
21
)/ln()/ln(
)(2
k
rr
k
rr
TTLQ
where L is the length of pipe, T1 and T2 are the respective temperatures at
the inner and outer surfaces of the insulated pipe, r1 and r2 are the
respective inner and outer radius of the steel pipe, and r3 is the outer
radius of the insulated pipe. ii) Latent heat of vapourization of steam could be taken as 2200 kJ/kg.
Questions from PM3125 / Feb 2010 past paper
R. Shanthini 19 May 2010
38
1) A fermentor containing 40 m3 medium at 25oC is sterilized by an isothermal heat source, which is saturated steam at 4.5 bar absolute pressure. Determine the time taken to heat the medium to 122oC. [06 marks]
Additional Data: - The density of the medium is 1000 kg/m3.- You may use the heat exchange equation
where U (= 695 W/m2.K) is the overall heat transfer coefficient, A (= 40 m2) is the heat transfer area, t is the time taken, M is the mass of the medium, c (= 4.187 kJ/kg.K) is the heat capacity of the medium, T0 is the initial temperature of the medium, T is the final temperature of the medium and TH is the temperature of the heat source.
- You may use the steam table (provided) if necessary.
H
H
TT
TTMcUAt 0ln
Questions from PM3125 / Sept 2010 past paper
R. Shanthini 19 May 2010
39
2) Fluid A enters the shell-side of a shell-and-tube heat exchanger at a flow rate of 3.60 kg/s at 200oC and it leaves the heat exchanger at 150oC. Fluid B enters the tube-side of the exchanger at a flow rate of 2.88 kg/s at 100oC. Heat capacities of fluids A and B may be taken as 3.0 and 2.5 kJ/kg.K, respectively.
a) Show that fluid B leaves the heat exchanger at 175oC under the ideal conditions of no heat loss to the environment. [04 marks]
b) Should the heat exchanger be operated at parallel flow mode or at counter-current flow mode? Explain your answer. [04 marks]
c) Show that the log mean temperature driving force is about 36. [04
marks]d) Determine the overall heat transfer area required assuming an overall
heat transfer coefficient of 414 W/m2.K. [06 marks]
e) If the length of the tube-bundle of the heat exchanger is limited to 2 m, determine the number of 25 mm internal diameter tubes required to construct the tube-bundle. [04 marks]
Questions from PM3125 / Sept 2010 past paper
R. Shanthini 19 May 2010
40
Critical Radius of Insulation
Ti – ToQ.
[ln(ro/ri)] /2πkPL
=
ri
ro
Ti
Tor Pipe
+ [ln(r/ro)] /2πkIL + 1/hairA
Insulation
Pipe resistance could be neglected
A = 2 π r L
Additional material not used in the lectures.
R. Shanthini 19 May 2010
41
Ti – ToQ.
= [ln(r/ro)] /2πkIL + 1/(hair 2πrL)
2π L ( Ti – To) =
[ln(r/ro)] /kI + 1/(hair r)Convective resistance
Insulationresistance
Increasing r decreases convective resistance and increases heat transfer.
Increasing r increases insulation resistance and decreases heat transfer.
Critical Radius of Insulation Additional material not used in the lectures.
R. Shanthini 19 May 2010
42
= 0 at the critical radius of insulation,
which leads to rcr = kI / hair
If the outer radius of the pipe (ro) < rcr and if insulation is added to the pipe, heat losses will first
increase and go through a maximum at the insulation radius of rcr and then decrease.
dQ.
/dr
If the outer radius of the pipe (ro) > rcr and if insulation is added to the pipe, heat losses will
continue to decrease.
Critical Radius of Insulation Additional material not used in the lectures.