R 9.0.0 Release Notes - CADISON · CADISON R9.0.0 Release Notes ISOGEN ISOGEN-Licenses Impact of...
-
Upload
truongkhanh -
Category
Documents
-
view
226 -
download
0
Transcript of R 9.0.0 Release Notes - CADISON · CADISON R9.0.0 Release Notes ISOGEN ISOGEN-Licenses Impact of...
R 9.0.0
Release Notes
Preface
A further CADISON release is available with the present CADISON Version. Extensive newdevelopments and further processing, special customer development and error correctionhas been under taken since the release 8.6.0.
The new CADISON functions must be known before the use by users and the CADISONsystem administrators, since with this an appropriate use of important changes can beunder taken in the projects.
This document can also be found in PDF format on our internet site:
http://www.cadison.com/Customers_Care/Updates.aspx
2
ITandFactory GmbH
CADISON R9.0.0 Release Notes
Inhaltsverzeichnis
CADISON R9.0.0 Release Notes 3Installation 4Overview of new functions 6Overview of function changes 9Overview of Bug fixes 14CADISON general 21 General 21 ACIS-Converter 32 Archiver 33 Report generator 34 Object model 36Designer 39 Designer General 39 PID-Designer 46 3D-Designer 48 Electric-Designer 51 ISOGEN 52 Visio PID 54Project-Engineer 57MATPIPE 60 Selector 66Project-Navigator 67Engineer2Web 68Administration 69 General 69 ITFTOOLS 71 API 73Conclusive Information 74
3
ITandFactory GmbH
CADISON R9.0.0 Release Notes
CADISON R9.0.0 Release Notes
Module Internetressourcen
Changes in CADISON:General | ACIS-converter | Archiver | Reportgenerator | Object model
www.cadison.com
Changes in CADISON Designer:General | P&ID-Designer | 3D-Designer |Electric-Designer | ISOGEN
Support:
FAQHotlineTrainingChanges in Project-Engineer
Changes in MATPIPE
Changes im Project-Navigator
Changes in Engineer2Web
Neu!New functions | Changes functions | Bugfixes
Admin General | ITFTOOLS | API
Copyright 2009, ITandFactory GmbHDate: 01.12.2009
ITandFactory GmbHAuf der Krautweide 32D-65812 Bad Soden
4
ITandFactory GmbH
CADISON R9.0.0 Release Notes
Installation
Prerequisites
Please read the installation instructions before installation.Further information is found under "Installation requirements" in the document availableon the installation-DVD: "CADISON_Installation.pdf".
Updating existing installations
Category: AdministrationPlease read the installation instructions beforehand.Further information is found under "Notes regarding update installation" in documentavailable on the installation-DVD: "CADISON_Installation.pdf".
The actual installation
Category: AdministrationPlease read the installation instructions beforehand. Further information is found under "Installation procedure" in the document available onthe installation-DVD: "CADISON_Installation.pdf".
Re-installation of CADISON R9.0
Please read the installation instructions beforehand. Further information is found on the installation-DVD: "CADISON_Installation.pdf".
Subsequent installation / uninstalling of a module
The setup supports the subsequent installation and thus the uninstalling of a module.The setup "CADISON" can be started through "Start > Settings > Control Panel > Add orremove programs" and "Change" can be selected. Please read the installation instructionsbeforehand. Further information is found in the document available on the installation-DVD:"CADISON_Installation.pdf".
Installing the network license manager (NLM)
Start the setup under NLM\Setup.exe from the CADISON R9 DVD.Further information is found in document available on the installation-DVD:"CADISON_Licensemanager.pdf".
5
ITandFactory GmbH
CADISON R9.0.0 Release Notes
Licensing
Catagory: AdministrationFurther information is found in the document available on the installation DVD:"CADISON_Licensemanager.pdf".
Scope of delivery
Along with the delivery of CADISON R9.0, you receive:
A program-DVD CADISON Release R9.0 A DVD with customised customer object model Release notes CADISON R9.0 (as PDF and CHM on the DVD)
6
ITandFactory GmbH
CADISON R9.0.0 Release Notes
Overview of new functions
CADISON General
Units with unicode signs/ special signs
Define a pattern object with alternative graphic
Request of the features from the revision documents
Internal file name comparison now not depending on small and capital wiriting
New functions for tables and column filters
Sub-divide other objects in CADISON table
Table dialouge can now been displayed internally in additonal columns
Archiver
New storing options
Report generator
New keyword SUMHIDE for word report generator
CADISON Project-Engineer
Entering files and emails using DragAndDrop
MATPIPE
Reference of LINK-Objects in formula
Copy catalouge
Open dialouge box anew
7
ITandFactory GmbH
CADISON R9.0.0 Release Notes
Update all duplicate objects
Language neutral attributes
Backup of sub-directories
User log in und user rights in MATPIPE
The search function in MATPIPE and Selector
Export and Import of a catalouge
Name and description for configuration
Process and change configuration
Updating configurations
Selector
Display of selected configuration
Load the current catalouge status
General administration
Renaming the users
Changing the GROUP.FLG files and unicode-Systems
Recreate GROUP.FLG correctly
ITF-Tools
Correction of dupilicate connecting points
ITF Dialouge box
New option -RESOLVEDEADTRANSACTION [Log-file]
New Option -DELDBSINRB [Log-file]
New Option -TRANSFERDOCS
8
ITandFactory GmbH
CADISON R9.0.0 Release Notes
Engineer2Web
Engineer2Web view of DWG and DXF files
9
ITandFactory GmbH
CADISON R9.0.0 Release Notes
Overview of function changes
CADISON General
Scroll bars in filter selection lists
Filter line in ListFromFile-selection dialogue
Selection of user defined table configuration
New selection window for the date
Background colors of the filter selection list in the table
Memory optimisation in case of several changes
Display of the project name in search result
Copying the memo texts
PDF-generation from XLS-files
New Versant Version
PDF-generation for new Microsoft Office file formats
"Cancel"-button in CADISON Tree-Dialogue
Display of the attribute "P_project"
Filling and numbering of unit fields
Takeover of a dictionary entry
Simultaneous read access to Unicode-files
Automatic re-filtering in case of change to a column filter
Issue of "Object description" in case of object locks
Takeover of column width in dialogue "Modify table configuration"
New function "Set property to default value"
Size of the selection list in case of table filter
Allocating and removing catalogue entries in case of locked objects
ACIS-converter
Undesired file name
10
ITandFactory GmbH
CADISON R9.0.0 Release Notes
Report generator
FILTERSUB with sub-ordinate components
Object model
Allocation of transmitter, transducer and devices to pipe
New default value of feature SETVISIBILITY
EX-features in case of object types PHI-ROOM and PHI-REGI
Heat changer, max 10KW
Min-value in case of temperature sepcifications changed to 273.15
Properties for drop in pressure calculation, Lambda-value is entered
Properties for drop in pressure calculation, Zeta value is entered
Type classes entered in case of „Valve [straight]" [PHI-PVLS]
Designer general
Sorting in dialogue "Object Designation"
Input of DWG-file names in symbol editor
"Merge objects" does not combine any labels
Problems while accessing character elements
Conversion of container assistants from VBA --> C++
Updating all currently loaded characters
Display of definition of configured labels
Highlighting function from the tree and the table that is to be docked
Data from / data to
Property ATTEXCHANGE not any longer dependent on case
11
ITandFactory GmbH
CADISON R9.0.0 Release Notes
3D-Designer
Segment curve
Flangs and coils were not correctly exchanged while changing the nominal diameter
Highlighting a 3D-graphic shows the diagram as a seperate point
Counter in section name
Extrusion while conversion in bent pipe
CADISON Project-Engineer
Selection of a display configuration in case of active table parts
Display of write protected MEMO-features in the table
New system error message
MATPIPE
Coloring of configurable duplicate objects in Matpipe-Tree
Input field enlarged
Log in name in CCC
Upgrading the processing of design specifications
Sorting the attributes in the main table
Retaining the object codes while changing the links
Commands for storing the configurations
ITF-Tools
Clearing up of unused graphical representations
12
ITandFactory GmbH
CADISON R9.0.0 Release Notes
ISOGEN
ISOGEN-Licenses
Impact of MLD entries for ISOGEN-piece list
Additional MLD features for elements of a screw type
Engineer2Web
Engineer2Web Timeout Problem
Visio PID
Performance optimization
Arbeiten mit mehreren Zeichnungen gleichzeitig
"Nächste" und "Vorherige" - Zeichnung Schaltfläche zum Wechsel zwischen den Zeichnungen
Baukasten
Rückgängig machen
Grafik austauschen
Copy&Paste zeichnungsübergreifend
Konfigurierbare Strukturansicht
Rohrleitungsfarbe und -Typ medienabhängig
Objekt in Rohrleitung bewegen
RGB Farbzuordnung, benutzerdefinierte Linientypen und benutzerdefinierteFließrichtungssymbole
.def Dateierstellung im Befehl "Neues Symbol erzeugen"
Erstellung einer benutzerdefinierten Anlage
13
ITandFactory GmbH
CADISON R9.0.0 Release Notes
ObjectInspector
Zeichnungen Synchonisieren
Objekt Skalieren Befehl
Neuer Separator im Befehl der Objekt Kennzeichnung
Design-Checker Befehl versteckt die Objekte nicht durchgehend
Hilfedatei kann nicht geöffnet werden
Das Auswählen mehrerer Verbindungspunkte für ein neues Symbol war nicht möglich
Leitung fortführen Dialog zeigte nicht die korrekten Rohrleitungsdurchmesser
Beibehalten der Flächen Verbindungen
14
ITandFactory GmbH
CADISON R9.0.0 Release Notes
Overview of Bug fixes
CADISON general
Importing existing characters as HookUp's
Abnormal end while selecting a deleted object
Unicode- database conversion
Blank session after integration
Input of a unit in dialogue "process attribute"
Abnormal end while generating report with unnamed property
Unicode characters in the selection list of the table headings
No icons in Tree in selector
Search in Tree
Abnormal end while importing existing documents
Excluded working copy cannot be incorporated
Abnormal end after unlocking the computer
Aborting the function "Attach catalog item"
Filter on "undefined" in table
Dialogue for "Find object..."
Incorrect display in selection list
File name "<<overwritten>>"
Text in waiting dialogue during the license test
Unicode-dictionary
Abnormal end while using the copy option "Reset document reversion"
"Check out to Working Copy" outsources several characters
Selecting a display configuration does not change the Tree-text of the project
Calculation of DNMAX in case of pipelines
Problem with Unicode in the ConfigManager-Dialogue box
Entries of file enhancements in CADISON.INI
Character revisions while incorporating
15
ITandFactory GmbH
CADISON R9.0.0 Release Notes
Updating the project object in CADISON-Tree
Abnormal end in case of opened Matpipe selector
Changing the column width in the CADISON table
Icon in title list of Memo-process-dialogue
Incorrect filter in table without class selection
Problems in case of huge project data with several objects
Resetting the order number
ACIS-converter
Abnormal end while converting flanges and dished boiler ends
Freezing of AutoCAD while converting N-edges
Archiever
Files are reconverted to "Transfered to database" while archiving
Change of the database project directory through archiving
Report generator
AutoCAD-command "Publish"
Report pattern with use of a wildcard property filter
Hanging of Word while creating / updating reports
The dialogue "Server is busy" while creating reports
Old report cannot be updated
Release of P_name in report
Object model
Incorrect text for ISOGEN-connection types MP and LN
16
ITandFactory GmbH
CADISON R9.0.0 Release Notes
Feature SALES_PRICE is calculated
Designer general
Problem with creating the active field while working with XREF
Duplicating connection points by using Copy&Paste
Copying/renaming dialogue after character verification
No SLD files creating symbols
Overwriting file as per "Save as"
Duplicate characters as per "Save as"
Elements are stored in incorrect layer
Duplicate copy dialogue while copying objects
Abnormal end during labelling
"Create revision table" shifts plot mode
Entering a file name in case of "Save as"
Bent pipe cannot be labelled with block and leader
Updating graphics while loading characters
Abnormal end of designer after moving a symbol
Infinite loops after processing a block
Graphics do not change as per "Copy Data from / Copy Data to"
Exceeding maximum number of selection sets
Changes to graphic of objects in loaded characters
Abnormal end while "Rotate object in line"
Symbols in characters change as per update on R8
Selection of a writing field while plotting
Loading the AutoCAD-Architectural-Functions
Leader of the text screen labelling is not drawn in the selected form
Creation of modules
Creating PDF- for DWG-files
17
ITandFactory GmbH
CADISON R9.0.0 Release Notes
Route look up in character adjustment
Highlighting in layout
Creating section in Russian AutoCAD-Version
Incorrect presentation of graphic as per "Move object in piperun or line"
Change in the flow direction deletes the database objects
Updating Excel-Reports
Error message "Unsupported event" while batch plotting
Incorrect result display in consistency test
Create a standard in dispaly window / in case of section
P&ID-Designer
Color of the leader changes while copying the layout
Character with MPL-line shows errors while opening
There is no flow direction arrow in case of MPL-pipelines
Error with the connection on end cap
Graphic variants swap with unsupported elements
Error in case of "Create visible pipe crossings"
Unicode sign within MPL style
3D-Designer
ISOGEN Layout-object and start point object hampers centre allocation
Bent pipe is generated with remarkable geometry
Bent pipe with incline
Selection of read files in XREF-Manager
Abnormal ending of AutoCAD while updating / exporting of 3D-elements
Abnormal end while labelling with block
18
ITandFactory GmbH
CADISON R9.0.0 Release Notes
Incorrect presentation of "New" primitive
Error in case of presentation and ACIS-converting of N-Edge MATPIPE-Primitive
Matpipe-Elements were no longer displayed in 3D-Mode
Abnormal end while drawing pipes
3D-display of wrongly parametrised Matpipe-Elements in Designer
Pulling the elements "Duct transition rectangular/round"
Electric-Designer
Display of graphic in dialogue "Allocate measuring point typical"
Error message in case of invalid object selection
Creation of HookUps
VBA-function "Batch processing of contact sets" replaced by C++ function
CADISON Project-Engineer
Adjustments for AKH - multiple Windows
On closing the window, parts of the symbol list disappear
Abnormal end while updating CADISON tree
Login-Dialogue appears on highlighting the object
Changeover between windows changes the structure view
Faulty menu and tool bar after incorporation
Changing the width of table column
Sorting in ascending order in the last column
Activating the table parts
Missing context menu for EDITABLEONETIME features in tables
Help button is referred to a wrong path
19
ITandFactory GmbH
CADISON R9.0.0 Release Notes
MATPIPE
Importing '999999999' from CSV-files
Display of links not selected while configurations
Cyrillic signs in parametric module
Duplication of duplicates
Field ReplicaID_ not filled in TGfxObject
Transfer problems of graphic parameters while replicating objects
Storing of configurations with CONFIGOBJ
Faulty error message in parametric module
Problem with opening of a second catalogue
Sorting in MATPIPE Report generator
Updating problem in MATPIPE Tree
Drag & Drop error in MATPIPE Tree
Abnormal end of program
Project-Navigator
Enter catalogue object
Administration general
Reading the variable "PHI_CONFIGPATH" in the correct sequence
Reading the variable PHI_CONFIGPATH
Abnormal ending of conversion tools in case of simultaneous conversion of several databases
Query of the user
NOMAT is marked as INVALID by DEFREAD
Option "Convert databases" in program UpdateDbs
20
ITandFactory GmbH
CADISON R9.0.0 Release Notes
ISOGEN
Abnormal end of the MLD-Editor
Extrusions on bent pipes in isometry
Creation and updating / revising isometric drawings
Feedback of ISOGEN position number as per CADISON
Engineer2Web
Special signs in dialogue "Über..."
API
Setting of feature values using CADISON API
21
ITandFactory GmbH
CADISON R9.0.0 Release Notes
CADISON general
General
New functions
#22405Units with Unicode sings / special signs
So far only the west European signs could be used for description of units (like e.g."Meter"). After this version it is also possible to use special signs or Unicode signs.
Note: It was necessary to change the internal database for this functionality. Due tothis reason, the existing databases must be first converted in the R9 database format.This conversion takes place automatically or the conversion program "Convertdatabases" can be used for that.
Definig a document object with alternative graphic
After this version CADISON is in the position to select an object graphic depending on anyproperties. Several graphics can be stored for one drawing type in case of one documentobject, and based on any one of the freely defined properties, CADISON can automaticallyuse one the graphics.
#21052Question of feature of revision documents
After this version, in case of documents, CAD drawings and reports, the following newproperties are available:
o P_lastrevisiono P_lastrevisiondateo P_lastrevisiondatetime und o P_lastrevisionuser
If in case of one the document object, the value of one of these properties is questioned,then all attached revision documents are determined internally from the document object.These are sorted as per date of creation (Property P_creationdatetime). The respectivefeature is returned from the last created revision date:
o P_lastrevision returns REVISION of last revision document.o P_lastrevisiondate Returns P_creationdate of last revision document.o P_lastrevisiondatetime returns P_creationdatetime from the last revision
document.o P_lastrevisionuser returns P_creationuser from the last revision document.
#22661Internal file name comparison is now case sensitive
CADISON internally sets a file name, sometimes only in upper case, sometimes lower
22
ITandFactory GmbH
CADISON R9.0.0 Release Notes
case, as it has been entered by the user (or as already available). In case of internal filename comparison, CADISON had evaluated the internally set file names differently andtherefore saves the new names, which pulls back further updates. Now at this point thename comparison is carried out irrespective of case.
New functions for tables and column filter
Some enhancements for the column filter / table filter are reconverted in the main table ofCADISON project engineer. For one, a list of three of the last used filters is directed per column. The last used filters are displayed in the selection list under the entries "All","Userdefined", "Empty" and "Not empty". If "Userdefined" is selected then automatically the last set filter, defined by the user isdisplayed in the dialog for definition of user defined filter, If in case this is still listed in thelist with three of the last used filters.
"Activate table filter" on: This entry in the context menu is provided with hook, if a filter isactive.
the hooks are removed while selecting the command and all filters in the table are reset. Thereby, which columns were filtered is stored (The names of the properties are stored). If this command is accessed again, then these columns are filtered anew. If the propertiesto be filtered are not present in the current table configurations then they are ignored.If a user defined filter is created, then this appears in the list of the last used filters with asyntax from which the parameter of the user defined filters are visible. The list of the last used column filter and the property name of all currently filteredcolumns is stored in the LocalCFG-folder in the file last.cpf.
#22507Other object sub-ordinated in the CADISON table
So far the command "Attach to another object..." was available only in context menu ofthe CADISON Trees or in extra menu of CADISON Project-Engineer. After this version, thiscommand can also be used from the context menu of CADISON table.
Table dialog can now be displayed in additional internal columns
Normally the columns to be displayed are specified in the table-dialog of the tableconfigurations. Now internally it is made possible to add additional columns per programming, at the startof the table.All other table functions must be by-passed. For example, these additional columns are not displayed when the current tableconfigurations are processed with "Configure table...".
Function changes
Scroll bars in filter selection lists
After this version, a horizontal scroll bar is displayed in the selection lists of the columnfilter, if the entries of filter lists are wider than the selection window.
23
ITandFactory GmbH
CADISON R9.0.0 Release Notes
Filter lines in ListFromFile-selection dialog
The handling of filter lines in selection dialog of ListFromFile-feature has been changed.Filters are work only after second entered letter. Thus a long list can be filtered quickly.Additionally the filtration is optimized so that longer lists are filtered quickly.
#21241Selection of user defined table configurations
If a table is available in a dialog, a user defined table configuration is selected in thistable. Then the name of the selected configuration is stored on the computer permanently.The list of previously selected configuration appears at the start of the next dialog.
#21184New selection window for the date
After this version, a new window is used for selecting the date while processing the datefields. Furthermore, the window which shows the calendar is displayed in better way inWindows Vista.
Background color of filter selection list in table
After this version, the entries in the filter selection list of a table column is presented withdifferent background colors. The fixed entries like e.g. "All", "Userdefined" are displayed inlight grey background, the entries of the last used filters in dark grey and the standardentry in white background.
#22020Display of project name in search result
If specific objects are searched with the function "Find object..." using several projects /databases and the search result has objects of several projects / databases, then thesearch result is displayed in the table dialog, the name of the project is displayed in thefirst column.
Copying the memo text
While copying the memo text, internal control signs can be changed using the Memo-process-dialog in CADISON. If the original text e.g. contains only the control sign 10 for anumber change, the this is copied and entered in other memo-feature (Likewise againusing the memo-process-dialog), So far the number change is automatically changed tocontrol sign 13 and 10. This could lead to problems in a separate object comparison inCADISON.After this version, the clipboard is corrected in this reference. If a text is copied from theMemo-process-dialog and the memo-process-dialog is closed an automatic adjustment ofthe text is carried out in CADISON - clipboard. If a different memo-process-dialog isaccessed and the text is added from the clip board, then the original text is receivedwithout any changes.
PDF-Generation of XLS-files
24
ITandFactory GmbH
CADISON R9.0.0 Release Notes
After this version, the spread sheet "CADISON_SYS" is ignored while creating PDF filesfrom the XLS-files. The "CADISON_SYS"-spread sheet is automatically created byCADISON. While using the Excel report generator has the parameters of report generator.This information is not required in case of PDF-file and hence it is no longer present thePDF-file after this version.
Break the connection to database
There is always an active database in Versant, which is within the Versant database (notto be confused with CADISON defdb). Sometimes the connection to the default database isbroken by the system. Later this can take of internal error messages in CADISON.Therefore, a change was given here. If in case the system breaks the connection to thedefault database, then the system reconverts the Versant default database to CADISONdefdb um. Thus no more errors are actuated later.
New Versant Version
After this version, CADISON uses Versant 7.0.1.4 with patch 12.
PDF-creation for new Microsoft Office file formats
After this version it is possible to create new Microsoft office file formats ".docx" and ".xlsx" by CADISON PDF files.
#20906"Abort"-button in CADISON Tree-Dialog
If a CADISON-command for creating object selection displays the CADISON tree dialog,then there was a possibility to break the object selection since the dialog does not have aabort button or a close button. After this version, an "Abort"-button is available for mostof the commands which use the tree-dialog for object selection. Thus the CADISON-command can be aborted.
Display of attribute "P_project"
All objects return the project name for the attribute "P_project", where the objects belong.If this attribute is added manually in a table configuration file then so far this attribute isdisplayed as editable, even tough changes have not been stored. After this version theattribute is no longer displayed as editable.
Filling and numbering the unit fields
When so far, the filling and numbering dialog was accessed for unit properties, then thedialog offered only a new input line for entering a new value. No units were displayed. Sofar the user was to enter the used un it manually.Through the available update, one receives one more selection list for the units in dialogin addition to the input lines for the value, whereby the basis unit has already been set. Ifa value is entered and subsequently the unit is changed, then automatically the enteredvalue is recalculated.
Note: With the recalculation, the entered value is displayed with a different numberwith decimal places.
25
ITandFactory GmbH
CADISON R9.0.0 Release Notes
#20411Takeover of a dictionary entry
If in dialog "Language support" an entry is taken over as per CADISON and the entry endswith a space, then the space at the end is automatically removed after this version.
Simultaneous read access on Unicode-files
If CADISON has a reading access to the text files, then this happens in so-called Sharemode, so that several CADISON-applications can be read simultaneously in the same files(Like e.g. the central configuration files). This share mode however does not work if itdealt with a Unicode text file in case of file which is to be read. The error has beenresolved.
Automatic re-filtering while changing a column filter
If in the table several columns have been filtered and one column filter is removed, thenin the previous versions (before R8.5) all currently filtered columns were filtered again. Sofar only the column was re-filtered in R8.5, where the filter was removed. Thus, it couldhave happened that the content was displayed in other filtered columns, which were notaccording to the current filter.The performance is changed through this update. As soon as a column filter is changed(not only when it is removed), all the currently delivered columns are automatically re-valuated. Thus, the display is correct anytime.
#21840Issue of "Object description" in case of object locks
If a database object cannot be locked for processing, then information about this object isdisplayed in dialog information. After this version, the objects labeling is displayedadditionally, if the objects have the information.
#21189Take over of column width in the dialog "Modify table configuration"
After this version, the current column width is taken over while accessing the function"Configure table..." in dialog "Modify table configuration". So far the column width wasdisplayed in dialog, how it was originally defined for table configuration.
New function "Set property to default value"
There is a new command "Set property to default value" in the context menu for a feature.If this command is accessed, then the selected feature is reset to default value, as it isstored in the object model.If only one object is marked (in a table), the context menu entry is displayed only if theselected attribute does not match the default value. If several objects are selected in onetable, then the command is displayed in the context menu.
Size of the selection list in case of the table filters
The selection list displays maximum 8 entries in the table filters. After this version theheight of the selection list is directed as per the size of the table. If the table is high
26
ITandFactory GmbH
CADISON R9.0.0 Release Notes
enough, then up tp 30 entries can be displayed in the selection list. If the table height isless then the size of the selection list is adjusted automatically (reduced).
Allocating and removing catalog entries in case of locked objects
After this version, in case of locked objects (e.g. locked using the command "WorkingCopy - Add object-locks within the database" no more catalog entries can be removed orallocated.If the context menu is accessed on a separate object, then the commands are de-activated in the context menu. If the context menu is accessed on several objects in thetable, then commands are available, however no action is taken in case of locked objects.
Bug fixes
#23676Importing existing drawings as HookUp's
So far, if using a command "Import existing documents", it was attempted to create aHookUp-drawing, then a red color cross was found in CADISON tree for the newly createddrawing. This error has been resolved.
Abnormal end while selecting a deleted object
It may happen that an object is displayed in a CADISON application, CADISON tree ortable, which is already deleted in a different CADISON application. As soon as this deletedobject is clicked a message appears saying that the object has been deleted.In very rare cases it could happen that CADISON ends abnormally instead of showing thismessage. This error has been resolved.
Unicode-Database conversion
In rare cases there could be problems with the Unicode-conversion of old data. Especiallyin case of databases which were present in outsourcing / integration, it may happen thatthe Unicode conversion was aborted by an error.
Blank setting after integration
In some cases it may happen that a blank outsourcing setting is displayed afterincorporating in the original database. This error has been resolved.
Input of a unit in dialog "Edit attribute"
The dialog "Edit attribute" is opened using the function "Change attribute for this objectonly...". A different display unit can be selected in this. In previous versions it waspossible to enter a completely new text. If this text is not defined in CADISON as a unit,the CADISON can no longer execute any recalculations.Because of this reason, after this version, new text cannot be entered in the selection listbut only the existing units can be selected.
27
ITandFactory GmbH
CADISON R9.0.0 Release Notes
#21963Abnormal end while generating reports with unnamed property
If an Excel-Report is started on an object, which contains unnamed property, then thereport generator ends abnormally. This error has been resolved.
#22262Unicode signs in the selection list of table heading
In some of CADISON-Dialogs an old version of CADISON is used. The selection list of thesetables, which were available in the title of the tables using Drop down lists, were usingolder signs. This cannot show any Unicode signs.After this version, the same signs were used for the selection lists, which is also used forthe tables. Thus Unicode signs were also displayed in selection lists.
No icons in tree selector
While accessing the CADISON CCC-test, as a first function followed by opening of theselector and display of catalogs which was used last during the CCC test, the Icons in thetree of the selector are not correctly displayed. This error has been resolved.
#22258Search in Tree
The search function in CADISON Tree had only worked for the Tree function, where thesearch function was accessed the first time. If e.g. several tree windows have beenopened in CADISON Project-Engineer, the search works only for that window which wasfirst started in the search functions. After this version, the search works in tree for allwindows.
#22273Abnormal end while importing existing documents
CADISON could end abnormally while using the context menu command "Import existingdocuments", if this command was used more than once. As long as no project databasewas opened, CADISON ends abnormally while using the command the second. If a projectdatabase was opened, this command was accessed and subsequently exchanged on theproject, the a fresh access of the command could lead to abnormal end. After this version,the command can be used with any problems.
#22495Outsourced spread sheet cannot be integrated
If an outsourced database is operated on several computers before integration, then onlythe data of first operation can be integrated. In existing versions the integration processused to freezes while the complete setting was deleted. After this version, the changes tothe first operation are integrated and the other operations are ignored so that at least thesetting in the source database is deleted.
#22092Abnormal end after unlocking the computer
28
ITandFactory GmbH
CADISON R9.0.0 Release Notes
When CADISON Project-Engineer starts CADISON PDM or CADISON Project-Navigator,then a CADISON login-screen appears. If at this point the computer is locked, thenCADISON ends abnormally without logging in and subsequently unlocking in CADISON.This error has been resolved.
#21647Aborting the function "Attach catalog item"
When the function "Attach catalog item" was used for an object which already containssub-elements, then CADISON asks if the existing sub-objects are to be deleted. There arethree options in the question dialog "Yes", "No" and "Cancel". In the existing versions theoption "Cancel" was reconverted as "No". The process could not be aborted. Afert thisversion, the process of catalog allocation can be aborted by selecting this option.
#21620Filter on "undefined" in table
If in a column the user defined filter was processed and thereby the filter value "--" wasselected, in most cases the filtering did not work correctly. After this version, the filteringis executed correctly on "undefined".
Dialog for "Find object..."Search routines can be stored and deleted in the dialog for object search. The safetyqueries or other notes did not have completed text till now, but only a code was given.After this version, the messages contain the complete text while deleting and addingsearch routines.
#23027Incorrect display in the selection list
If one CADISON feature is processed using a selection list, then it may happen that theavailable entries are wrongly displayed in the selection list. If the entry has a semi colon,then the entry is displayed as two entries. This error has been resolved.
#22661File name "<<overwritten>>"
If a document contains a file name in a project, which is already in used in the projectthen CADISON automatically sets this file name to "<<overwritten>>". After this versionthe text "[[overwritten]]" is used as the sign "<" und ">" [and] is not allowed to be usedas filename and therefore CADISON cannot change the file name. Due to this CADISONcould end abnormally.
#23052Text in waiting dialog during license test
Text was adjusted in CADISON project engineer, AutoCAD Designer and Visio Designer,which is displayed during the license test.
Unicode-dictionary
29
ITandFactory GmbH
CADISON R9.0.0 Release Notes
The dialog "Language support" allows CADISON to process the currently set dictionary. Forthis the buttons "Add the language", "Delete the language", "Insert entry" and "Deleteentry" are present the dialog. When in case of the current dictionary it deals with Unicodefile, then these buttons are not available. This error has been resolved.
#22661Abnormal end while using the copy option "Reset document revision"
If the current diagram revision was attached in Designer and copied with "Save as", acopy dialog appears. If the option "Reset document revision" is selected then Designer endabnormally. This error has been resolved.
#22949"Check out to Working copy" outsourced several drawings
While outsourcing the data it may happen that the drawings, which are not neededdirectly, have not been outsourced, in order to process the primary selected data. Afterthis version, all the indirectly connected drawings are no longer outsourced whileoutsourcing but just the direct ones.
Selecting a view configuration does not change the Tree-Text of the project
If a view configuration has been selected in tree or the table using context menu entry"Select configuration...", all display texts of the objects are updated according to thenewly selected configuration.Till now however the texts of the project object are not updated on the tree but alwaysUpdate Tree must be actuated by pressing F5. After this version the project-object text is immediately updated on selecting a different view configuration.
Calculation of DNMAX in case of pipelines
The feature DNMAX in case of pipelines determines the largest nominal diameter of allpipe runs. This does not work if the nominal diameter specifications were integral inchspecifications, like e.g. 20".
#23439Problems with UniCode in the ConfigManager-Dialog box
Unicode signs were not correctly displayed in the ConfigManager Dialog box. This errorhas been resolved in the current version.
Entries of file enhancement in CADISON.INI
If a file is opened with context menu command "Display file..." or "Open file..." fromCADISON, then CADISON searches a matching file enhancement in CADISON.INI. If noapplication key has been entered in case of document in CADISON (under the PropertyAPPLICATION_CD), then file enhancement is used. Thereby till now the file enhancementin CADISON.INI should have started with a point (like e.g. ".JPG"). After this version,point must not be entered.
#21607Drawing revisions while integration
30
ITandFactory GmbH
CADISON R9.0.0 Release Notes
If during outsourcing, a drawing revision is outsourced, then it is not taken back in theoriginal database while integrating the project (Since a revision is write protected and isnot allowed to be overwritten).Since CADISON R8.0.1 this drawing revision is left in setting, so that the settings cannotbe automatically deleted by CADISON after integration. This error has been resolved.
#21614Updating the project object in CADISON-Tree
If an object has been changed in CADISON, the display text of the object is automaticallyupdated for CADISON-Tree. This, however does not work for project features P_prjnumberand P_prjstate. If these features were used for the display text and the values of thesefeatures were changed, then till now the display text were not updated in tree.
#21262Abnormal end in case of opened matpipe selector
If the Matpipe selector was opened in Engineer and subsequently CADISON tree inEngineer is clicked in case of opened selector window, then CADISON 8.5 endsabnormally. This error has been resolved.
Changing the column width in CADISON table
In CADISON R8.5.x, in some functions, the tables were not correctly evaluated after somecolumns were moved through Drag and Drop. Thus the print function did not note thechanged columns in the table. There could be display problem even while activating anddeactivating the adding function, if some columns have been moved. These problems havebeen resolved.
Icon in title list of Memo-process-dialog
The Icon in the title list of the Memo-process- window has been drawn with an incorrectscale under Windows Vista. After this version the Icon is displayed with the correct pageratio.
#20850Incorrect filter in table without class selection
The filter does not work correctly if the table configuration was changed in a table wherethe class selection is not available. When the filter list was opened in a column, then thecontent of previous columns is displayed.
Problems with larger project databases with several objects
CADISON uses internally storage optimized function after a specific number of object in aproject database, in order to access the objects. These functions could cause severalproblems. So e.g. it may happen that the changes to project object were not written in thedatabase reliably or that CADISON ended abnormally with the error E3003. This error hasbeen resolved.
#20266
31
ITandFactory GmbH
CADISON R9.0.0 Release Notes
Resetting the contract number
If a current order number has been set in a project then it was always automatically resetevery time new objects were entered. This error has been resolved.
32
ITandFactory GmbH
CADISON R9.0.0 Release Notes
ACIS-Converter
Function changes
#22789Undesired file name
When the ACIS converter is accessed, an option dialogue appears, where the parametercan be set. In case of entered file names, till now, always an entered file enhancement isremoved and replaced by ".sat" or ".dwg". After this version, ".sat" or ".dwg" is stillattached, if in case the entered file name does not end with this file enhancement. Thuseven the file names like "ausgabe.test.sat" can be generated.
Bug fixes
#22922Abnormal end while converting hoses and dished boiler end
The converter may crash when the ACIS-converter converts a character which containsthe hoses and dished boiler ends or angular curves. After this version, characters whichcontain these object types can be converted without any problems.
#23119Freezing of AutoCAD while converting N-corners
In rare cases, it may happen that the AutoCAD does not react anymore, if an N-corner isto be converted in ACIS-element. This problem was resolved in this version.
33
ITandFactory GmbH
CADISON R9.0.0 Release Notes
Archiver
New functions
New archiving options
New options have been incorporated in Archiver. Now the following two additional entriesare supported in the configuration section [ITF_ARCHIV]:
[ITF_ARCHIV]ArchivFailedFolder=Archiving failed AutoExpireTimeInMonth=0 MaxSizeToExportInMB=0
If while archiving a database, an error occurs, then the database in CADISON tree ismoved in database group, which is entered in the line ArchivFailedFolder=, whereby thedatabase group is created manually.Using the AutoExpireTimeInMonth= it can be specified that the database is archivedautomatically. This database cannot be changed for the specified time. This option worksonly on the database server as the database server is directly checked for this purpose. Avalue of '0' (this means the default value) means that the Archiver does not search the olddatabase (Only the database from the Archive-folder is archived).The maximum size can be specified with the line MaxSizeToExportInMB. This line permitsa database with that it can be still archived. A value of '0' (which is the default value)means that the size is not limited.
Bug fixes
The files are reconverted to "Transfered to database" during archiving
The document was always automatically reconverted to "transfered to database" when itwas not read previously and if archiving a database, in case of a document, had problemsin reading or copying the file. There appears an error message that the document was notcopied and the archiving was aborted. However the document is subsequently on"transfered to database". The read status is no longer changed after this version.
Change of the database project folder through archiving
After archiving a database it is moved in CADISON-Tree (either in the database group forfaulty logs or in the recycle bin-database group). Thereby, till now the project folder waschanged by the database without however renaming the project folder. If project wasaccessed, CADISON was not able to find the project files. After this version the projectfolder of the database is no longer changed after archiving.
34
ITandFactory GmbH
CADISON R9.0.0 Release Notes
Report generator
New functions
New keyword SUMHIDE for Word-Report generator
After this version the new keyword $SUMHIDE$ is available. This keyword adds up objectssame as the keyword $SUM$, however there is no output in the report. Thus, it is nolonger necessary to format the text "$SUM$" as "hidden" in the report form.
Function changes
#23298FILTERSUB with sub-ordinate components
A FILTERSUB can be defined using the "P_treeobjects" during report query. Using thisthose objects which do not have sub-objects of specified types can be removed. Until nowonly the sub-ordinated structure elements were searched. The FILTERSUB- part of thereport query was enhanced in this version so that even sub-ordinated components can besearched. The new syntax of FILTERSUB-share of the report query is:TYP_S1,TYP_S2,TYP_Sn:TYP_K1,TYP_K2,TYP_KnThe types of colon are searched as structure sub-element, while the types search thecolon as components -sub-elements.
Bug fixes
#19843AutoCAD-command "Publish"
If the AutoCAD-command "Publish" has been used when several drawings were loaded,then either a dialog with question - if the current drawing is to be copied or renamed, or adialog with note - already a file of same name is present, appears in designer.This error has been resolved in this version.
Report pattern with use of a Wildcard-Propertyfilter
It possible to use a property filter in a report pattern. It is possible to work with the wildcrads signs "*" and "?" within this filter. If these signs have been used, then the reportcould not have been created correctly. This error has been resolved through this update.
#23164Hanging of word while creating / updating reports
While using Office 2007 with SP1 / SP2 it may happen that word hangs and does not reactwhile creating a report. The performance dependend on the used report pattern. After thisversion, such a problem never occurs.
35
ITandFactory GmbH
CADISON R9.0.0 Release Notes
Dialog "Server is busy" while creating report
While creating a report, it may happen that a dialog "Server is busy" is shown by theoperating system and thus report generation is interrupted. After this version, this dialogis disabled so that reports can be generated without interruption.
#22947Old report cannot be updated
When, in case of an old report the absolute path to report pattern originally used has beensaved in the feature VIEWTYPE, then it was not possible to update this report in CADISON.This error has been resolved. After this version, report can be updated but however report-replacement file REPORT.TPM is not noted.
#23299Issue of P_name in report
If in a report form, the report syntax "$P_project.P_name$" and also "$P_name$" is used,then the property "P_name" of the project is issued twice. This is generally applicable forall properties, which have been requested using "$P_project...$". This error has beenresolved.
36
ITandFactory GmbH
CADISON R9.0.0 Release Notes
Object model
Funktion changes
Allocation transmitters, transducers and measuring devices to pipeline
Until now a transmitter/ tranducer/ measuring device were not automaticallysub-ordinated to pipeline, when such an object in flanged execution had been entered in a3-D pipeline. The allocation is executed automatically after this version.
#21630New default value of the feature SETVISIBILITY
The ground value for the feature SETVISIBILITY was changed from "Yes" to "No" in theuser adminstration. This was executed for user objects and also for user groups. After thisversion, explicit authorisations must be issued in the user adminsitration in order to givethe user an access to the functionalities of visibility control.
#21617EX-Features in case of object types PHI-ROOM and PHI-REGI
In case of these object types, the text of selection lists for feature EX_TCLASS(Temperature class) was changed.In addition to that the selection list of the feature EX_GROUP was enhanced to a newvalue and a new feature EX_GROUP_KEY was added. Furthermore the new featureEX_GROUP_KEY is used in the EX_IDENT formula.
Heat exchaning device, max 10KW
The maximum value for the object classe "Heat exchanger" (PHI-HEXC) was increased incase of the feature "Heat transmission power" (HEAT_PWR).
Min-value in case of temperature specification changed to 273.15
In case of all temperature specification, the minimum input value was set to -273,15°C
Properties for pressure drop calculation, Lambda-value entered
In case of the following object classes, the feature "Pipe friction coefficient (Lambda)"[VALUE_LAMBDA] was newly accepted:Pipe (PHI-PIPE), bent pipe (ITF-BNDP)
Properties for pressure drop calculation, Zeta-value entered
In case of the following object classes the feature "Resistance factor (Zeta)"[VALUE_ZETA] was newly accepted:Compressor (PHI-CMPR); Pumps (PHI-PUMP), Filter (PHI-STRN), Hose (PHI-PHOS), curve(PHI-PARC), T-piece (PHI-PTEE), four way connector (PHI-PCRO), reducer (PHI-PRED),
37
ITandFactory GmbH
CADISON R9.0.0 Release Notes
Dev. RLT (PHI-PEQI), compensator (PHI-PCMP), Strainer (PHI-PFLT), fittings (corner)(PHI-PVLE), fitting (three way) (PHI-PVL3), fitting (four way) (PHI-PVL4), fitting (straight)(PHI-PVLS), Muffler(PHI-PSIL), connector (PHI-PFIT), Flange (PHI-PFLG), connectionelement (ITF-COUP), Bushing (PHI-PSCK), bushing (PHI-PCOP), Nippel (PHI-PNIP), Bolting(PHI-PJNT), Flange (PHI-PBRD), coil (PHI-PBND), Weldseam (PHI-PWLD), Couppling(PHI-PCON), fitting (Multiport) (PHI-PVLM), extrusion/outlet (PHI-POLT), Y-Stück(PHI-PYTE), device heating/cooling jacket (PHI-THEC), branch saddle(PHI-PSAD),connecting branch (PHI-PELT).
Type classes in case of "Valve [straight]" [PHI-PVLS] entered
In case of object class "Valve [straight]", the feature "Type Class" [TYPECLASS] was newlyaccepted:
following selection list is stored:Blocking fitting, straight;Blocking valve;Stop cock, general;Gate valve;Shut-off valve;Check valve, general;Check valve;Check valve;Fitting with constant adjustment characteristic;Fitting with safety function;Ventilation and exhaust fitting
The background of this adjustment is a differentiation for Matpipe selector. In order to beable to use this function, the following basic conditions are to be adhered to:
o The an_art.flt must be amended for the object class "Valve [straight]" to searchcriterion [TYPECLASS].
o The feature [TYPE CLASS] must be added as main entry and as per the catalogobject an entry must be selected from the selection list.
If the entry matches with "Valve [straight]" in Engineer with the catalog object, then therespective catalog object is displayed in the "Search result" tab of the selector.
Bug fixes
#22011Incorrect text for ISOGEN-connection types MP and LN
For the JOINTYPE-feature in CADISON, until now the ISOGEN-Option MP was displayedwith "Liner" and the option LN with "Male Part". This allocation is interchanged. After thisversion, for ISOGEN-option MP, the text "Male Part" is displayed and for option LN "Liner",exactly like it is documented in the CADISON ISOGEN help file.The actual database content remains unchanged. The inventry data is displayed only witha different text after a CADISON-Update on this version.
#21516Feature SALES_PRICE is calculated
38
ITandFactory GmbH
CADISON R9.0.0 Release Notes
Until now, in case of object model "Commercial Extension" the feature [SALES_PRICE]"Sales price total" was not automatically calculated in case of all object types. Oneformula was stored in the object model, however the feature type EDITABLE is used. Afterthis version, the type CALCULATE is used, so that the sales price is calculatedautomatically.
39
ITandFactory GmbH
CADISON R9.0.0 Release Notes
Designer
Designer General
Function changes
#21688Sorting in dialog "Object Designation"
The entries in the list of dialogs "Object Designation" and "Configured Designations" aresorted. Thereby, until now however the numbers in the entries were not sorted correctlye.g. "Userfield 10" before "Userfield 2". After this version the number were correctlysorted in the texts.
#22314Input of DWG-file name in symbol editor
In symbol editor in AutoCAD Designer, an input field is present for entering file names forthe graphic files for the symbols to be created. Until now maximum 8 characters could beentered. After this version, up to 200 characters can be entered in the field.
#20570"Merge objects" does not merge labels
If an object has been labeled and then processed with Designer-command "Mergeobjects", then the original object is deleted, since the labeling has not been transferred tothe objects to be merged.If the command "Merge objects" has been accessed from the Engineer, then the labeling isautomatically merged.
Reconversion of the container assistant from VBA --> C++
The container assistant has been implemented in AutoCAD under VBA. Since all sourceshave been reconverted to C++ and MFC, now only the container assistant was in line.In container assistant, it is possible to store a configuration of a container in a file. Here achange was given. Old files are naturally compatible with the new container assistant. Thefiles generated with the new container assistants do not operate in all versions. It couldend abnormally if used in old container assistants.
Updating all presently loaded drawings
If several drawings have been loaded in designer and processed in active drawingCADISON-Objects, then all presently loaded drawings are updated. During this process,until now the docking tree dialog was updated a number of times (for each loadeddrawing). Since while updating drawing is not necessary, this process is not executed afterthis version.
Display of definition of configured labeling
The current setting of labeling is displayed in just one line in the dialog to configure labels(general labeling functions). In case of longer definitions, only the start of the definition isseen. After this version, the setting is displayed in multiple lines.
40
ITandFactory GmbH
CADISON R9.0.0 Release Notes
#20702Highlighting function from the docking tree and tables
If one of the Illumination-Functions is accessed from the docking tree and table and thedialog is not docked at present, then it is faded while highlighting the docking tree ortables so that the drawing of these dialogs is hidden.Thereby the docking dialog is faded, using which the Illumination-Function has beenaccessed.
#20898Data from / Data to
While selecting the objects in Designer, in case of both the functions a note "Selectobjects" appears.This is changed now:
o In case of function "Copy Data to" --> select target object o In case of function "Copy Data from" --> select source object.
#20693Property ATTEXCHANGE no longer dependent on case
Until now the feature ATTEXCHANGE is always entered in upper case and thus thematching attribute file was found. After this version it is no longer necessary.
Bug fixes
#22931Problem with setting the active field while working with XREF
If a drawing contains several XREF's and these drawings as well as the XREF filesassociated with it are loaded in the same designer-setting it could have problems underArchitectural Desktop 2009, if these drawings were active in different (e.g. in XREF-files ofmodel field, while the paper field is active in the main drawing).Partly, the processing of XERF files could lead to the fact that an incorrect field wasdisplayed by ADT 2009 as active in the main drawing.
#22607Duplication of connection points by using Copy&Paste
If in AutoCAD elements are copied and entered with Copy&Paste and thereby theassociated database elements are also copied, then while entering the graphics, it couldhappen that in case of some database objects the connection points are doubled. Thishappens in case of database objects which were additionally copied as sub-ordinatedobjects of the original objects selected graphically. After this version, the connectionpoints are no longer duplicated in case of these objects.
#22095Copying /renaming dialog after character test
41
ITandFactory GmbH
CADISON R9.0.0 Release Notes
Start Designer and wait till it is automatically stored by AutoCAD.Subsequently access the drawing verification: The copy/rename dialog appears, whichshould be then broken with Task- manager so as to prevent further damage.
#21547No SLD files while creating symbol
1. If in symbol-editor a default object is generated and the new default object "Scale block1x1x1" is selected, then preview cannot be seen. *.sld-files are not created 2. If the selected graphic presentation (2D/3D/Symbol) does not match the drawingsetting, then preview is not created. *.sld-files are not generated
#22661Overwritten file as per "Save as"
When the current drawing has been copied with "Save as", it may happen that the originaldrawing in the database is set on "<<overwritten>>" and thus will not be available anymore. This error has been resolved in this version.
#22661Duplicate drawings as per "Save as"
If in the design, the current drawing is copied with "Save as", then it may happen that thedatabase creates two copies of the drawing and one of it is set on "<<overwritten>>".This error has been corrected.
#22769Elements are stored on incorrect layer
If a layer name is defined using the object model, then a corresponding layer isautomatically created in AutoCAD and used accordingly. If e.g. in case of a pipeline a layername is defined, then this layer name is used for the graphical pipeline elements.Thereby, until now it is not tested if the layer name has characters, which are not allowedto be used in AutoCAD. Thus till now the objects are stored in the incorrect layer.After this version, the layer name is checked for invalid characters (The characters are <> / \ " : ; ? * | , = '). If invalid characters are present, then these are replaced by aunderscore _ .
Note: The original name database is retained, the name will be adjusted at runtime,only within AutoCAD.
Double copy dialog while copying objects
If objects are copied in a drawing by graphical selection, then depending on the selectedobjects a CADISON copy dialog appears, where the database objects which are copiedmust be selected. In some rare cases it may happen that the copy dialog appears again,after the objects have been copied (or have been added again). This error has beenresolved.
#22527Abnormal end while designate objects
42
ITandFactory GmbH
CADISON R9.0.0 Release Notes
The control of some buttons was faulty in the "Object designation"-dialog. So it waspartially possible to use "Apply"-button, although "With labels" and "With leaders" wasselected. This could lead to abnormal ending of the Designer. After this version the buttonis available in case of respective option selection.
#22755"Create revision table" adjusts plot mode
In a layout multiple drawing revisions are created, then it may lead to change in thePlot-setting of the display window. Especially the option "Hidden" could thereby adjustedby the AutoCAD to "As displayed". This error has been resolved.
#22661Input of a file name in case of "Save as"
When the current file is saved with "Save as" in Designer then a dialog box appears forinput for new file name. Thereby it is checked whether the file name is already in use, asnew files names must be same within the project. Until now the test did not workcorrectly, a file name, which already exists in the project could have been given here.Thus the existing files are overwritten.
#22749Bent pipe cannot be labeled with block and leader
Until now a bent pipe could not be labeled with a block and leader since the layerdefinition for the leader is not available. After this version the layer for the leader isdefined.
#22240Updating the graphics while loading characters
While loading a drawing in the designer, it is tested if the graphics of drawings are stillactive. If not then these are updated automatically.Thereby there could be problems if the same drawing has been already loaded and loadedanew in the current designer setting. The graphics were not updated partially in thecorrect manner.
#22345Infinite loops after processing a block
If a block is directly processed in the current drawing in Designer using theAutoCAD-command REFEDIT and the current drawing or AutoCAD has been closed withouthaving to end REFEDIT-command, until now CADISON loaded in an infnite loop, since itwanted to save the drawing. However this dose not happen as long as theREFEDIT-command is active.After this version CADISON no longer runs in the infinite loops. The drawing cannot besaved. When the question "Save drawing" appears in AutoCAD, then it must be answeredwith "Yes", since at this point AutoCAD issues an error message and the close command isbroken. After that REFEDIT must be ended before AutoCAD is completed again.
#21955Graphic does not change as per "Copy Data from/Copy Data to"
43
ITandFactory GmbH
CADISON R9.0.0 Release Notes
When the data of one object with catalog entry is transferred to another with thecommands "Copy data from" or "Copy data to", then the graphic available on originalobjects is transfered to the target object. Thereby in case of target objects, a new defaultgraphic is activated.When the target object has already been placed in a drawing, then until now the graphicrepresentation of the target object is not updated automatically. This error has beenresolved.
#22365Maximum number of selection sets has exceeded
An AutoCAD selection list is used if while using CADISON explorer an option is selected ora different input point is reconverted with the space bar. This selection set was so far notreleased in existing CADISON. If the maximum number of available selection sets, i.e. 127has been achieved, then AutoCAD releases a corresponding error message in theAutoCAD-command line.after this version, the selection sets are released in correct manner so that the AutoCADmessage is no longer visible.
#22249Graphic presentation of objects in loaded drawings
If several drawings are loaded in Designer and if in one of the drawings changes are madein an object, which has an effect on graphics in other drawings, then these graphics areautomatically updated in other drawings.Until now, in some rare cases it could have happened that such graphic changes were notexecuted. This error has been resolved.
#21668Abnormal end incase of "Rotate object in line"
If the older CADISON explorer is activated in Designer and the command "Rotate object inline" is accessed then Designer ends abnormally. This error has been resolved.
#21599Change symbols in drawings as per Update in R8
In some cases it may happen in CADISON R8.x some symbols are replaced by othersymbols. This error has been resolved.
#21623Selection of a title block while plotting
While plotting CADISON searches for title blocks that contains the attributes RECEIVERand PRINTDATE. If a matching title block has been found, then these attributes areupdated automatically. If more than one matching title block is found, then the user mustselect one so as to end the plotting process.Thereby until now all layouts of the current drawing are analysed and not just the activelayout. If a different layout title block was available but not presently, then in spiet of thatCADISON asks for the title blocks which are to be updated. Since none were available inthe current layout, the user was not able to select any and thus the plot process could notbe ended. The Designer must be then ended in Task manager.
44
ITandFactory GmbH
CADISON R9.0.0 Release Notes
#22757Loading the AutoCAD-Architectural-Functions
So far if CADISON Designer was used based on the AutoCAD Architectural 2009, then notall Architectural commands are available, if the CADISON-Profile has been used. After thisversion, while using AutoCAD Architectural 2010, the Architectural commands areavailable even while using CADISON-Profile.
#23389Leader of the text screen labeling is not drawn in the selected form
Leader of the text screen labeling is always drawn with an arrow, eve though the user hadselected a different form (with full stop/slash/without).
Creation of modules
If modules are created in Designer, it may happen that the creation of these modules isinterrupted with a message that documents could not be read. If in existing versions,subsequent objects were added in the drawing, then these are not permanently stored inthe drawing. This error has been resolved after this version.
PDF-creation of DWG-files
The PDF-creation of DWG-files was not working till the path for DWG file or the DWGfilename had a point. This error has been resolved.
Route look up in drawing storage
Route search in drawing storage dialog does not work any more since CADISON R8.Always a message appears that no rout was found. This error has been resolved.
#21421Highlighting in layout
If one of the highlighted function is used in paper field of a layout, then it may happenthat after removing the highlight, the layout view has been destroyed and the layout mustbe restarted.After this version, while highlighting a layout, the previous view is no longer reset. If theview is changed in the layout while highlighting, then CADISON does not return to theprevious view after completing the highlighting.
Section creation in Russian AutoCAD-Version
The CADISON-section creation function does not work under Russian AutoCAD. This errorhas been resolved.
#21306Incorrect graphic presentation as per "Move object in piperun or line"
45
ITandFactory GmbH
CADISON R9.0.0 Release Notes
If in a 2D-drawing the Designer command "Move object in piperun or line" is used, then itmay happen in case of some objects that an incorrect graphic or too many attributes aredisplayed at the end of the command. Especially those symbols which used a graphicalreconversion of the attribute "Normally open/Normally closed" (RESTPOS).
#22127Change to the flow direction deletes database objects
If during connection the flow direction has been changed, then a new copy is internallycreated by the database objects associated with it and the original database object isdeleted.While deleting the original database objects, even the sub-ordinated components weredeleted, thus database objects could be deleted by changing the flow direction.After this version, the sub-ordinated components of the original database objects aretransferred to the copy, thus deleting of the original database objects does not delete thecomponents. These are automatically sub-ordniated to the new database object afterchanging the flow direction.
Updating Excel-Reports
So far there was the option "Create in background" in the dialog "Update report". If thisoption was selected for Excel-Reports, thus the excel-report file is destroyed.Nor can the creation or updating of Excel reports executed in the background, then thisoption is de-activated in "Update report"-dialog.
#21491, 22444, 22718Error message "Unsupported event" while staple plotting
Under AutoCAD 2009, a message saying "Unsupported event" may appear when the stapleplotting functions has been accessed. This message may appear after entering the nameof the recipient. The error message does not appear after this version.
#22964Incorrect result display in consistency test
During the consistency test the nominal diameter and nominal pressure are tested. Theresult table has two columns "DN" and PN". Thereby it may happen that one nominaldiameter has been displayed in "PN"-column. The result display was changed in such away that both (different) nominal diameters are displayed in the "DN" column if there areany different nominal diameters.
#21213Set measuring point in the display window/ section
So far, the setting of measuring points in a display window or while creating a sectiondisplay did not work in the Russian version of CADISON. This error has been resolved.
46
ITandFactory GmbH
CADISON R9.0.0 Release Notes
PID-Designer
Bug fixes
#22703color of the leader changes while copying the layout
The color of the leader changes when the layout is copied while labelling in layout.
#22761Drawing with MPL-lines shows errors on opening
While opening those drawings which have MPL lines, it may happen that a message"vcdb_MPL::dwgInFields Style ID NULL" appears, points that the used MPL-style is notavailable. Although the concerned MPL-lines were shown till now, but could not bedeleted. This status could lead to abnormal end of AutoCAD / the designer.After this version the concerned MPL-lines is reset to MPL-Style "Standard". With this theMPL lines can be correctly selected as per the loading process and processed further
#21586No flow direction arrow in case of MPL-pipelines
The flow direction arrow in case of MPL-pipelines, under some conditions is not displayedunder AutoCAD 2009. This error has been resolved.
#21854Error on connection on end caps
In CADISON R8.5, it is now not possible to place a connection on an automatically createdend cap.
#22089Graphic variants exchange with unsupported elements
The command "Exchange graphic representation" works only with AutoCADBlock-Elements (Insertion). If other graphics have been selected, (like e.g. Poly lines)then the command cannot exchange any graphics. Till now the command did not give anymessages when an invalid element was selected. After this version, a message is given atthe start that a block is to be selected and an appropriate error message is given when noblock is selected.
#23039Error in case of "Create visible pipe crossings"
If the command "Create visible pipe crossings" is executed and a pipe run (which isselected as constant pipeline) crosses a drive shaft then it is broken.Thereby the drive shaft loses the allocation to main object and subsequently remains"lose" in the database. In order to correctly execute "Create visible pipe crossings" withmechanical connection, signal line or working line, the attribute "Breakmode" has beenadded in the object model for the three classes "PHI-MCON", "PHI-SIGL" and "PHI-EFFL".
47
ITandFactory GmbH
CADISON R9.0.0 Release Notes
Unicode sign within MPL style
The MPL module of CADISON was not able to handle Unicode signs correctly till now. Forone there were problems in dialogues for definition of MPL-styles, for some no MPL-stylecould be saved or loaded, Unicode signs which were present in the definition (e.g. Stylename or block name). These problems have been resolved in this version.
48
ITandFactory GmbH
CADISON R9.0.0 Release Notes
3D-Designer
Change of function
Segment curve
Segment curves have now been converted from VBA to MFC.
#23131Flanges and coils were not correctly exchanged while changing the nominaldiameter
In case of a pipe line the nominal diameter can be changed in a 3D drawing. For thispurpose the available elements are automatically exchanged by other elements usingMatpipe Selector. Until now flanges and coils were not exchanged correctly as these werenot entered in the FLT configuration files and thus mergeobject search was not possible inthe catalogs. The FLT-configuration files were enhanced for flanges and coils.
#22982Highlighting a 3D-drawing shows the drawing as a separate point
In some cases it may happen while highlighting 3D drawings that the limits of the objectsto be highlighted have not been determined correctly. Thereby, the drawing is zoomed outso much that it appears as a point. After this version the geometrical measurementscannot be determined from the 3D object, instead of that the input point of the 3D objectwas used.
#22819Counter in section names
A code letter has been determined by CADISON in the "Section"-Dialog for a section to becreated. Until now this code letter was increased on every access of the section function,even when the section-dialog has been ended with "Abort"-button. After this version, thesection letter is increased only when the dialog has been closed with "OK"-button.
#22522Extrusion while conversion into bent pipe
If an existing pipe line is made out of separate pipes and curves and extrusion has beenplaced there and this pipe line was then transformed in to a bent pipe, then the availableextrusions were deleted. After this version, the available sub-objects of the existing pipesand bents are transferred on the bent pipe so that other sub-components are not lostbecause a bent pipe is created.
Bug fixes
#22714, 21886ISOGEN Layout-Object and Start point -Object hampers centre allocation
49
ITandFactory GmbH
CADISON R9.0.0 Release Notes
If in case of a 3D pipe line ISOGEN layout- objects (like e.g. ISOGEN flow direction arrow)or ISOGEN start point has already been placed and subsequently the centre allocation isaccessed, then the center was not correctly allocated with pipes and curves. After thisversion, these ISOGEN objects were ignored by the centre allocation
#22762Bent pipe is created with remarkable geometry
The function for creating a bent pipe expects a specific sequence in case of connectionpoints. It is expected that a pipeline element is connected with connection point 2 withconnection point 1 of the next pipeline element. As soon as a pipeline element had beendrawn with a different flowdirection, this sequence was no longer given. From thisgeometry if a bent pipe was created, then this would have has an incorrect line flow.After this version, the creation of bent pipes is no longer dependent on a specificconnection sequence.
#22934Bent pipe with incline
Until now only the pipe lines could be transformed into bent pipe, if the pipe run had a 90degree bent. After this version even the bents can be used with different angles.
#22929Selection of read files in XREF-Manager
When a new file is to be allocated or super imposed in XREF-Manager, CADISONautomatically transfers the selected file, if it has already been read in the database. Untilnow the file was not transferred and no note appears.
#22097, 22717AutoCAD-Abnormal end while updating/ exporting 3D-Elements
In some cases it may happen that while updating a Matpipe 3D elements AutoCAD mayend abnormally with "Unhandled Access Violation"-Message. Likewise AutoCAD could endabnormally while exporting a drawing to NavisWorks or NavisWorks could abnormally enda DWG file if opened directly.For this the actuator can be 3D graphic which cannot be created (If e.g. The parametricfrom the matpipe cannot be built). Since the 3D-Graphic can be a basis for furtherauthorization (like e.g. Object start, Volumes calculation, etc.), till now it endedabnormally when a different CADISON function needed this information.
From this version CADISON no longer ends abnormally, but the required informationis not available (eg, the volume with "0" is calculated, or there are no object catches) are available..
#22602Abnormal end while labeling with block
When in a layout it is worked with the CADISON command "Designate objects with block"and positioning of the blocks of the caption is achieved under a viewport, then in rarecases, AutoCAD could end abnormally. This error has been resolved.
50
ITandFactory GmbH
CADISON R9.0.0 Release Notes
#22081Incorrect presentation of "New" primitives
If 3D graphic is built in a Matpipe, then with each one of the most primitive identifications,one of the codes "Unite", "Subtract" oder "New" can be used. So far, it could have lead todisplay errors while using the "New" option in AutoCAD, when an object was rotated, anda 3D display had been activated (eg, "3D Wireframe").Similarly, an incorrect graphic was made, if such a Matpipe element was initiated inAutoCAD with the command EXPLODE.
#23192Error while presentation and ACIS conversion of N-Edge MATPIPE-Primitive
Error while displaying and ACIS conversion of the N-Edge MATPIPE primitives. Especiallywhen the body is eccentrically extruded with holes.
#22980Matpipe-Elements are no longer displayed in 3D-Mode
In rare cases, it could happen that after opening a 3D drawing some 3D elements fromMatpipe are no longer displayed, as soon as a 3D display (eg, 3D wireframerepresentation) has been activated in AutoCAD. This error has been resolved.
#23220Abnormal end while pulling the pipes
When it is worked in AutoCAD with the command STRETCH and CADISON 3D pipes wereselected then it could lead to abnormal ending of AutoCAD depending on the set view.This error has been resolved.
#220863D-Display of wrongly parameterized Matpipe-Elements in Designer
In Matpipe, in case of graphic parametrization it can be specified for each primitive,whether a new primitive or a primitive to the previous primitive is to be added orsubtracted. It is possible to set the first primitive to subtract. From CADISON R8 suchMatpipe objects in CADISON designers in a 3D display are no longer displayed. After thisversion such Matpipe objects are displayed again, whereby naturally the first Subtraction-Primitives not displayed.
#21269Moving the element "Transition rectangular/round"
When a ventilation device of the type "Duct-Transition rectangular/round" was movedwith the CADISON Move command, the length of the object is changed. Likewise with theuse of CADISON command "Copy and rotate objects" would temporarily change the objectlength. After this version, the object length is no longer changed while moving andcopying.
51
ITandFactory GmbH
CADISON R9.0.0 Release Notes
Electric-Designer
Bugfixes
Display of graphics in dialogue "Allocate measuring point typical"
The graphic of the selected typical is displayed in the dialogue. Till now this was active fortypicals, which were saved as .DEF-files. The graphic is displayed even for newly createdtypicals which were still not saved in .DEF-files.
Error message in case of invalid object selection
If in case of cable router, an invalid object is selected in the graphic, then till now perhapsan internal error message like "Zugriffsverletzung" [Access violation] or something similaris dispalyed. This error has been resolved.
Creation of HookUps
The function for automatic creation of HookUps among others cerates piece lists in thegraphic. The definition of piece lists was present in the fixed defined DWG-pattern. Afterthis version, it can be freely defined, as to which DWG-pattern is to be used for the pricelists.
VBA-Function "Batch processing of contact sets" replaced by C++ function
VBA-Macros for command "Batch processing of contact sets" are re-programmed in C++.
52
ITandFactory GmbH
CADISON R9.0.0 Release Notes
ISOGEN
Function changes
ISOGEN-License
After this version a license is required for isometric generation using ISOGEN. This iswritten off on accessing the isometric generation and released after ending the designer.
#21324Effect of MLD-entries for ISOGEN-piece lists
During isometric generation, similar objects are entered in the ISOGEN-piece list. Theobject feature ISOGEN-DESCRIPTION is used for consolidating similar objects. It ishowever, possible to release additional object features in the ISOGEN piece list, if the MLDfile is enhanced accordingly. While consolidating similar objects no entries from the MLDfile were considered till now. So it would happen that the objects in the piece list havebeen consolidated in the piece list although separate entries could have been created.Thus, after this version, the entries from MLD file is noted during object comparison.
#21295Additional MLD features for elements of a screw group
If in ISOGEN-Stil in .MLD-file, additional features are defined for the piece list, then tillnow these are not used for all elements of a screw group but only while moving the screwgroups. After this version the additional features for all elements (Screw, nut, and discs)are released.
Bug fixes
#21852Abnormal end of the MLD-Editor
Because of abnormal ending of the program, the working folder for ISOGEN MLD editor ischanged from (…\CADISON\App\Alias) to (…\CADISON\Config\VCS-IGEN) in CADISONR9.
#22522Extrusion on bent pipes in isometry
If extrusions are attached in a 3D drawing on a bent pipe and ismoetry is to be createdfrom the pipeline, the process breaks with ISOGEN-error message "Disconnected Pipeline".After this version, the extrusions can be released in the isometry, when the feature"ISOGEN component-identifier" is set to "OLET" during extrusion.
Creation und updating / revising of isometric drawings
While creating isometric drawings, all isometric pages (dxf-files) of pipeline created byISOGEN are imported and stored as layout in a Dwg-file, when the project has
53
ITandFactory GmbH
CADISON R9.0.0 Release Notes
"ISOGEN-PIPE-SINGLEDWG" attribute and it is set on "1(Ja/Yes)". Thereafter it is possiblefor the user to control the user interface if while creating the new isometr the currentisometry is just updated or revised automatically.
#21378Feedback of the ISOGEN position number as per CADISON
If in designer, a pipeline isometry is generated, then CADISON automatically creates aposition number for all positions. This number can be automatically imported in CADISON.This was not working till now when specific characters were present in pipeline names(Which were invalid for creating a file name). This error was resolved.
54
ITandFactory GmbH
CADISON R9.0.0 Release Notes
Visio PID
Function changes
Performance optimizationConsiderable improvement in performance while moving multiple object at a time.
Working with multiple drawing at a time
Now it is possible to open multiple drawing in a single Visio instance and can work withthem by switching from one to another.
Next and previous button for the drawing switch
It is possible to switch to other drawings in current project through direct command.
Construction set
It is possible to create construction set for existing CADISON objects.
Undo
It is possible to undo the previous operations from drawing and also reflectd in database.
Exchange Graphic
It is possible to change the graphic representation of object placed in the drawing.
Copy paste across the drawing
It is possible to copy object/objects from one drawing to another along with databaseassociated with it across drawings which are open in single instance of Visio.
Configurable structure view
It is possible to configure the number of items in the structure view combo box in thecustom tree (This is applicable only to new tree dialog available only in Visio Designer).
55
ITandFactory GmbH
CADISON R9.0.0 Release Notes
Pipeline color/Line type based in the mediaPipe line color and line type can be changed based on its superior media object.
Move object in pipeline
It is possible to move objects by maintaining its existing connections to other objects.
RGB color mapping, user defined line type and user defined flow directionsymbol
Now it is possible to map AutoCAD color to VISIO in the RGB format. Also AutoCAD linetype and Arrow symbol can be mapped with user defined line type and Arrow in VISIO.
.def file creation in Create new symbol command
One definition file will be created after creation of a new symbol from creates new symbolcommand which can be used to create.objects in other default databases.
Creation of user defined logical plantIt is possible to create logical plant with non-rectangular shape through assign graphiccommand.
Object Inspector
· New better look of object inspector with vertical show hide button at tab level andalso this dialog is made dockable.
· Changing the selection object in drawing will automatically update the contents ofObject Inspector.
Synchronize drawingWhile placing the object in the drawing, first object will attach to the mouse cursor andthen user will be able to place at desired location with left or right mouse button click.
Scale Object CommandCurrent scale of the object will be displayed in the scale dialog.
New separator in the Object Designation commandNew designation separator like "-", "." and new line are added in this command.
Design checker command doesn't hide objects consistentlyDesign checker was not hiding objects consistently. Sometimes object use to remainhidden after re-opening the drawing.
56
ITandFactory GmbH
CADISON R9.0.0 Release Notes
Unable to open Help fileVisio online help was not getting invoked from certain dialog.
Unable to select multiple connection points for new symbolCreate new symbol was not allowing to select multiple symbolic connection points in onesymbol.
Continue pipeline dialog doesn't show correct pipe diameterContinue pipe line dialog was not displaying the correct diameter of selected pipe run.
Maintain shapes connectivity
It is possible to move objects by maintaining its existing connections to other objects.
57
ITandFactory GmbH
CADISON R9.0.0 Release Notes
Project-Engineer
New functions
Adding of files and eMails per DragAndDrop
After this version, it is possible to add files from Windows explorer and emails fromMicrosoft Outlook through Drag and Drop in the opened project.
Function changes
#21133Selection of display configuration in case of active table separator
If the table separator is active in the main window of Engineer and until now a new displayconfiguration (via the"Select configuration ..." context menu has been selected in thetree, then the table has not been updated. After this version, the table is rebuilt accordingto the selected configuration. Thereby it is attempted to get the current position of thetable separator. If the new table does not have enough column, the previous position ofthe table divider cannot be restored, then the table separator is moved to extreme left.
#21154Display of write protected MEMO-features in the tables
If in older versions of CADISON (prior to release 8.5.0) MEMO feature has beendouble-clicked in the table, then it is was always reconverted to input mode. This wasdone for read protected-MEMO features, since with that by activating the input mode, thebutton for opening the MEMO editor was available. Therefore the complete text wasdisplayed even in case of write protected MEMO features. Changes were not saved in caseof write protected MEMO features.In version R8.5.0 it was no longer possible to reconvert in Engineer main window in theinput mode in the table. After this version, this functionality is available again.
#23368New system-error message
From this version, the new error message "Invalid parameter for CRT function" appears onscreen in the Project Engineer in case of internal errors. The same message is alsorecorded in CADISON.ERR. Previously, the Project Engineer would end abnormally becauseof these internal errors, after this release the error message appears. Subsequently, theProject Engineer is no longer stable and should be ended as soon as possible.
Renaming of documents without enhancing the file name
While renaming the documents, the new document name should always include a filenameenhancement. the following rules apply while changing the document name:
1. When a filename enhancement is specified, then this is used.
2. If name no name enhancement is entered for the new document, then the file name
58
ITandFactory GmbH
CADISON R9.0.0 Release Notes
enhancement is automatically taken over from the old names, provided it was available.
3. Renaming of documents without enhancement is no longer possible. A message thatthe filename enhancement has failed appears.
Bug fixes
#22822-22824, 22826Adjustments for AKH - multiple Windows
Diverse problems were resolved in the more window operation of Engineer within thescope of AKH specified version:
1. After starting the program, now 2 windows are opened in the AKH-version in thecorrect layout (30/70). The Tree in additional window is now sorted. Now in the leftwindow the structural view "not processed" is set.
2. 2 new windows are opened in the AKH version with the command "New Window".Now, only one window is opened correctly that one which lies exactly over theexisting window.
3. While closing one of these windows, an unsystematic part of the symbol list iseliminated. Now the symbol list is reduced only then when the last window isclosed.
4. Now the structural view a d the associated TOP5 lists are directly displayed andevaluated in AKH-Version after starting the program.
5. The name of the AKH specific TOE-Export-Function was changed to EDS-export incontext menu.
#22826Parts of symbol list dissapear while closing a window
If an existing window is closed at start, then a part of tool bar in the symbol listdisappears. The menu is completely visible only after restarting the Engineer.
#22468Abnormal end while updating the CADISON Tree
When F5 is pressed in Tree to updated CADISON-Tree, the Engineer ends abnormallywhen the project-object is visible in the tree outside the drawing.
#21667Login-Dialog appears while highlighting the object
If an object is edited in Engineer and highlighted, then it is required to login to CADISONwhile opening the Designer. This login window did not appear in 7th version.
#23332Changeover between windows changes the structured view
When several tree windows have been opened and a different structure view is selectedfor the current window using the "Structured view"-Dialog, then an incorrectly activestructure view is displayed in the selection list of the structure view after activating thetree window. This error has been resolved.
59
ITandFactory GmbH
CADISON R9.0.0 Release Notes
#21394Faulty menu and error toolbar after integration
If a project is opened in Engineer, which has a drop down and the project is integratedagain, then this project is deleted in the drop down. Thus by deleting the project the treewindow is automatically closed in Engineer. In the previous version however, the toolbarand menu is not updated so that then engineer ends abnormally while selecting a toolbarcommand or menu command.After the integration and deletion of the project, automatically the menu bar is removedafter closing the tree window and the tool bar is reset, so that a new project can bestarted from there.
#21337Changing the width of the last table column
In CADISON R8.5, it was partially not possible to change the column width of the lastcolumn in the table in main window. This error has been resolved.
#20954Ascending order of sorting in the last column
In R8.5 it was not possible to sort the last column in the table in ascending order in themain window of Engineers. This error has been resolved.
Activating the table section
If the table in main window of Engineer has already been scrolled towards right andsubsequently the heading lines of the tables are displayed on the context menu of tables,then until now the table heading was displayed on incorrect position. After this version,the table is compeletly scrolled to the left and only then the table heading is displayed.
Missing context menu for EDITABLEONETIME features in table
The context menu entry "Clear and unlock property" is not available on the table in themain window of the Engineers for the feature of type EDITABLEONETIME. This error hasbeen resolved.
#20978Help button refers to an incorrect path
There is a help button in engineers Dialog "Structured view->Modify Structured ViewDefinition...". The error message: "The file …\cadison.chm was not found" appears afterclicking the help button. This error message referes to an incorrect path. This error wasresolved in CADISON R9.
60
ITandFactory GmbH
CADISON R9.0.0 Release Notes
MATPIPE
New functions
Refernce to LINK-Objects in the formula
So far it was necessary to use the name of the Link object in order to relate to a feature ofsub-object in a formula (e.g. the term "LINK1.P_name" refers to the feature "P_name" ofthe sub-object, which has been defined under "LINK1").After this version it is also possible to relate to a special sub-object using the link positionnumber. For this purpose, the new keyword "POSx" is added, whereby "x" must bereplaced by the position number of the link object.For example, the term "POS2.P_name" refers to the feature "P_name" of the sub-objectwhose link has position number 2.
Copy Catalog
After release 9, the user can directly create a copy or a revision of Catalog in MATPIPE.This new command was implemented in the form of a context menu in the new Catalogselection dialogue box.
New opening dialogue box
In MATPIPE R9, the standard dialogue box to open the Catalog was replaced by a newone. The new dialogue box offers a better handling and overview of all available Catalogsand its content. The Catalog can be represented in a list or a tree format. The user canimmediately see which objects are found in the Catalog by clicking a Catalog in the list.Furthermore, additional information like the Catalog labelling and revision is alsodisplayed. Using the user rights, only those Catalogs can be displayed in this dialogue box, where theregistered user orders the respective rights.
#15629Update all dupilicate objects
Now, the duplicate objects of all available Catalogs or all selected Catalogs can be updatedin MATPIPE with one command. The new command can be accessed from MATPIPE menu"Extras-->Update Replica". Besides, the command can be executed from "Commandprompt", when the MATPIPE is started with parameter "UPDATEREPLICA" . Furtherinformation is available in MATPIPE Online help.
#16031Language neutral attributes
In addition to checkbox "Multi Lingual" one more option "Language Neutral" is available inthe dialogue box for attribute features. This option can be activate only then when "MultiLingual" has been selected.Activation of "Language Neutral" results in display of attribute names in MATPIPE tables asjust one single entry, e.g. "Material (Language neutral)" and not as "Material (german)","Material (english)" etc. as until now. This means that the labelling in all languages issame and it is handled accordingly in MATPIPE as well as in CADISON.Maintenance of data for language neutral attributes is not necessary in CADISON
61
ITandFactory GmbH
CADISON R9.0.0 Release Notes
dictionary.
Back-up of sub-folders
After release 9, MATPIPE finds those Catalogs which are found in the sub-folders withinthe Catalog path. Closed Catalog folders are not supported, i.e. if a Catalog is found in asub-folder then MATPIPE igonres all Catalogs under it, if some more Catalogs are found inthe folder or sub-folders present in it.
#19903 User login and user rights in MATPIPE
Now, after release 9, MATPIPE has access adminstration. Each CADISON user can beallowed or denied the access to Catalogs and functions in MATPIPE by the CADISONadministrator. Each user who starts MATPIPE must login yo the CADISON system. He canuse a function in MATPIPE or open a Catalog only after successful login. Thereby he can use only those functions and open those Catalogs for which he has authorisation.The access rights for MATPIPE are assigned in CADISON user adminstration.Following three rights for MATPIPE can be assigned to a user:
o MATPIPE Administratoro Change Catalog structure o Datamaintence
The authorisation can be idividually assigned to each user.
The search function MATPIPE and selector
After release 9, a new search function is available in Matpipe and also in selector in orderto quickly find Catalog objects. In Matpipe, the function can be accessed from the menupoint "Edit-->Catalog ObjectFind" and in selector using the button "Find object". Thesearch screen appears using this command. In the search screen, one can choose theobject type and filter, define as well as specify in what Catalog the object search is carriedout, for the desired feature. The result is displayed in a list. If an entry is selected in thelist, then the datalogue is opened directly and directed to the selected object in tree.
Export and Import of a Catalog
In MATPIPE R9, a MATPIPE Catalog can be exported with all files and then imported to thesame or a different computer. The new commands can be executed using the menu point"Catalog-->Export..." or "Catalog-->Import...". These functions are implementeddepending on the user rights in MATPIPE. If a catalouge in CADISON domains has beenassigned with specific users, then it cannot be used overall in the domain, if same usersare not available in other domains. The new export function removes all authorisationinformation from the Catalog and subsequently packs up all Catalog data in anunrestricted zipfile "*.mpex". This file "xxx.mpex", can be imported anytime with the helpof MATPIPE Import function.
#14977 Name and description for a configuration
While creating a configuration, it is possible to give a name and description for thisconfiguration in MATPIPE as well as in Selector.Here Matpipe / Selector automatically assigns a defualt text for configuration description.The current user name, date and time is entered by default. If a user does not want to
62
ITandFactory GmbH
CADISON R9.0.0 Release Notes
save this information then he must manually change this text.With the help of this process, additional information desired by most of the customers isreceived automatically without further user interaction (Creator and creation date).If it is reconverted to "Configuration" view in Matpipe or in Selector, then configurations ofthe same names appear in the tab "000-Favorites" of the detail table. If a configurationhas been selected, then a window appears which otherwise displays main entries anddescription of selected configuration. "Edit Configuration description" from the contextmenu can edit this data.
#20859Process and change configuration
After this version, if a configuration in the detail tabel is right clicked, thenMatpipe/Selector checks if this configuration has a sub-object "CONFIGOBJ". If anything isindeed available, then a new command "Edit configuration" is displayed in the contextmenu. On accessing this command a dialogue appears to change the data processor"CONFIGOBJ"-Objects, "CONFIGOBJ". If the dialogue has been ended with "OK" , then anew sub-entry is stored in the Catalog for "CONFIGOBJ". "CONFIGOBJ" uses the newsub-entry.
Updating configurations
After this version, the context menu in tree offers a new command "Update configuration"in Matpipe and in Selector. If an existing configuration has been selected in"Configuration"-tab and reconverted to "Catalog"-tab, then the selected configuration isdisplayed as active in green. The configuration can be changed there (e.g. select othersub-elements). New command "Update configuration" can be used from the existingconfiguration in order to complete the change so as to overwrite the existingconfiguration. However, a new configuration can be stored with "Save configuration".Note: In case of active CCC-functionality, a new time stamp is created by updatingconfiguration, in case of main object and the name of the last operator is updated. Thus,the CCC test in CADISON can determine that the configuration has been changed. Theconfiguration can be automatically updated there.
Functions changes
#20531coloring of configurable duplicate objects in Matpipe-tree
Duplicates in Matpipe tree are always shown in blue. If it deals with a configurable object,then it is displayed in red as a normal configurable object. Thus it was not clear that itdeals with a duplicate.After this version, the configurable duplicates are displayed in a different color. Likewise anew color is used in tree for the configured duplicates.
Enlarge input fields
The input fields in the dialogue box to create a new Catalog are enhanced. This change isexecuted in reference to the change in release 8.0, where the length of Catalog search hasbeen changed to 65 characters.
Login name in CCC
63
ITandFactory GmbH
CADISON R9.0.0 Release Notes
The name of registed user in MATPIPE/CADISON is taken over as the login name for CCCchanges. If MATPIPE is executed in stand alone mode, then the windows login name isused as before.
Improvisation of processing of Assembly rules
An entry must be made in the dialogue box for processing assembly rules by doubleclicking in the bottom field "moved" so that it can be edited. But it was deleted in the listabove and should have been added anew with "Insert" after changing and moved to theold place with "Up arrow"/ "Down arrow".Additional to the "Insert" button a new buttom "Change" implements which changes of theselected entry serves in the list.In order to simplfy the processing of entries in this list, along with "Insert" button,"Change" button is implemented in release 9, which serves the changes of the selectedentries in the list.Furthemore the size of the dialogue box can be changed now.
#20458Sorting of attributes in the main table
A sorting function is implemented in MATPIPE main table, which sorts the attributes withinthe tab. The sorting is in alphabetical order.
Retaining the object codes while changing links
In case of CCC functionality activated in Matpipe, all matpipe objects automatically get aunique code. Until now this code was reset, if it dealt with a configurable object inmatpipe, in this case a link was added or deleted. After this version, the object code wasretained with addition or deletion of links. Instead of that only the internal time stamp andname of the processor is updated.
Commands for storing configurations
The commands for storing configurations in tree context menu is now highlighted in grey,after this version, if the configurable obejct has still not been completely configured. Thisis same in Matpipe as well as selector.
Bug fixes
#22462Importing '999999999' from CSV-files
While importing CSV-files (not only in case of CSV import, even for neutral import), it mayhappen that the unit fields of value '99999999' has been saved as '1000000000' afterimporting. This error has been resolved.
#22180Display of links not selected during configurations
64
ITandFactory GmbH
CADISON R9.0.0 Release Notes
In the display tab for configurations, all features of the main object and those ofsub-objects (link-objects) are directly displayed in the detail table. When a sub-object isan optional sub-object and has not been selected for configuration, then the default valuefrom the feature definition appears in the detail table as value for this feature. After thisversion, the text "Link not configured" is displayed in the table.
Note: The text is displayed in red to cleary identify that it does not deal with regular text.In Matpipe red is used for showing errors, in this case however it does not deal witherrors.
#23311Cyrillic sign in parametric module
Until now Unicode signs like e.g. cyrillic signs were not used in the formula window inparametric module of Matpipe. These were partially displayed as question marks or theentire formula was considred invalid. After this version, even Unicode signs can be used informula input fields.
Duplication of duplicates
In Matpipe, it is possible to create new duplicates from the replaced data. Thereby, tillnow in target catalog, the references were partially created on the original cataloge,partially even on the catalog which has the first duplicate. After this version the entiredata of duplicates refers to original catalog.
Field ReplicaID_ is not filled in TGfxObject
When objects are duplicated in other catalogs, till now the field ReplicaID_ has not beenentered in the table TGfxObject. Normally, the record ID from the original catalog is to befound there.
#23231Transfer problem of graphic parameter while makeing object duplicates
In MATPIPE Release 8.6, there is a program error concerning the duplication of catalogobjects. I.e the graphic parameters are not transfered in the target catalog whiledupilcating the objects, if the name of source catalog was longer than 16 characters. Thiserror has been resolved in the current version.
Storing of configurations with CONFIGOBJ
When a configuration, which has an optional CONFIGOBJ, then a dialog appears where thethe data for CONFIGOBJ can be entered. If no data has been entered in this dialog thenan invalid configuration was stored till now, which was not able to be entered in CADISON.This errror has been resolved. After this version, storing such a configuration creates anew entry in the detail table of CONFiGOBJ-Object. This entry is uses the default valuefrom the object model. The configuration subsequently uses this new object.
Faulty error messages in parametric module
An error message is issued, when numerical value, which is outside the defined interval,has been entered in parametric module. Since R8, this error message could have signswhich cannot be read. This problem is resolved in this version.
65
ITandFactory GmbH
CADISON R9.0.0 Release Notes
Problem with opening two catalogs
One catalog is open and attempt is made to open another catalog.If the second catalog cannot be opened, then following error occurs in the catalog view:Now only the catalog tree can be seen. The fields for object class lists, master or detail listview and the preview is highlighted in grey. This porblem can ne solved only by openingthe catalog again. This error was resolved in release 9.
#19720Sorting in MATPIPE Report generator
The MATPIPE Report generator was until now not in a position to correctly sort the texts,which comprises of alphabets and numbers. i.e. it was sorted just alphabetically. Thus theresult was that the text "DN20" was larger than text "DN100". This error is resolved inRelease 9.
#21175Updating problem in MATPIPE Tree
Updating had not properly workd while entering the data in a newly created catalog. Whena new section is created in new catalog or the features at the section level have beenprocessed, then the desiredpresentation for this level is updated only after closing the treeor after quiting the catalog. If, e.g. a new object was created, then it could happen thatthe symbols for already existing objects in tree have been replaced by Quader or cylinder.This error was resolved in the current version.
#21382Drag & Drop error in MATPIPE Tree
MATPIPE ends abnormally, when one has moved a specification object in an open catalogthrough Drag and drop on the top most source object. The error has been resolved.
# 21261Abnormal end of program
MATPIPE abnormally ends while accessing an object if a property has been defined in thisobject and whose name had a point. In MATPIPE R9, it is no longer possible to define aproperty name, which contains a point.
66
ITandFactory GmbH
CADISON R9.0.0 Release Notes
Selector
New functions
Display of selected configuration
When a configuration is selected in selector and subsequently changed to tab "Catalog",then all modules of the selected configuration are displayed as configured. This meansthat all the configured links and the detailed table entries associated with it arehighlighted in green. The tree in selector can be redesigned by pressing F5 and thecoloring can be reversed.
Loading the current catalogue status
Till now it was not possible to get the current status of the catalogue in CADISON Selectorif in case the catalogue has been changed in the background. In CADISON R9 there is anadditional button "Reload catalogs". This command, like "Update index", also includes allcatalogues so that the internal "Selektor Cache" is emptied. Subsequently, the currentcatalogue status is loaded anew.
67
ITandFactory GmbH
CADISON R9.0.0 Release Notes
Project-Navigator
Bugfixes
Enter catalouge object
The command "Insert object from catalogue" was till now available from the tool bar aswell as the menu. As the Project-Navigator permits only reading access, no action isexecuted during selecting the command. After this version, the command is deactivated inthe tool bar and also in the menu.
68
ITandFactory GmbH
CADISON R9.0.0 Release Notes
Engineer2Web
New functions
Engineer2Web view of the DWG and DXF files
A new menu was added for displaying the DWG and DXF files.
Function changes
#21938Engineer2Web Timeout Problem
The Timeout for script manager consists of just 90 seconds.
Bugfixes
#21935Special character in dialogue "Über..."
In Engineer2Web Administrator Tool, the special character was displayed in the dialogue"Über...".
69
ITandFactory GmbH
CADISON R9.0.0 Release Notes
Administration
General
New functions
Renaming the users
After this version, it is possible to rename the user in the CADISON- user adminstrationwithout compelling to transfer the new user in the existing project database.
#20993Change of GROUP.FLG files to Unicode-Systems
When the additional programs startalldbs, stopalldbs and emptylogfiles are used on thesystems, in case of which a Unicode -code page is active (like e.g. in case of Russianoperating system), then incorrect content of the GROUP.FLG-files is written with by theseprograms. After this version the GROUP.FLG-files are correctly changed.
Correctly restore GROUP.FLG
Till now it could have happen that the CADISON additional programs startalldbs,stopalldbs and emptylogfiles have changed the GROUP.FLG-files of the database and havenot been corrected till the end as after using these programs, a different content was to befound in the GROUP.FLG files. After this version, the original content was rewritten at theend in the GROUP.FLG-files.
Bug fixes
#21749Transferring the variable "PHI_CONFIGPATH" in correct sequence
Transferring the variables "PHI_CONFIGPATH" for determining LocalCfg path was notcorrectly executed by CADISON administration tool "Configmanager". These variablesshould be transferred from the section of the current domains. If unavailable, then fromthe section "PHi-CADISON"."Modules.ini".
#21749 Importing the variables PHI_CONFIGPATH
The CADISON Config-Manager had imported the variable "PHI_CONFIGPATH", in incorrectsequence from CADISON.INI.The access to these variables must be in the collowing sequence:Transferring the variables from the section of the domain, if unavailable, then from thesection PHi-CADISON.
#21331Abnormal end of the conversion tool in case of simultaneous conversion of
70
ITandFactory GmbH
CADISON R9.0.0 Release Notes
several databases
The database conversion program can convert several databases simultaneously. efollowing entry was not available in CADISON.INI:[PHi-CADISON]FAST_RELEASE_OBJECT_COUNT=0
After this version, it is no longer necessary to create this entry in CADISON.INI, beforeseveral databases are simultaneously converted with the conversion tool.
#21937Queries of the user
The CADISON API offers a function to to request the available user. Till now this functionreturns all use objects, which were available in the system database. Thereby it is nottested if found user has been actively allocated to a user adminstration. After this versionthose users are informed who belong to active user adminstration.
NOMAT is marked as INVALID by DEFREAD
The value "NOMAT" can be entered in the object model files in the columnCATALOG_LEVEL. Till now DEFREAD.EXE infoms this value as invaild. After this versionDEFREAD.EXE identifies it as valid value.
#20981Option "Convert databases" in program UpdateDbs
The option "Update only Object modell"in the database conversion program was notcorrectly placed while changing the size of a window. Besides the "Maximieren"[maximise]-button of the window was not available till now.
71
ITandFactory GmbH
CADISON R9.0.0 Release Notes
ITFTOOLS
New functions
#22607Correction of dupilcate connection points
While using the Copy&Paste function in AutoCAD, it may happen that in case of some dataobjects, the existing connection points may become double. These unnecessary connectionpoints are searched in database and deleted using this option. This option gives outcorresponding messages when unnecessary connections points were removed. In thiscase, the ITFTOOLS -XCLEAN tools must be used in order to ensure that the databasestructure is correct after removing the connection points.
ITF Dialog box
The ITF-Dialog box was renewed.
New option -RESOLVEDEADTRANSACTION [Log-file]
If during operating CADISON, project database is deleted, then in most of the cases it mayhappen that the so-called Dead-transactions are created. Through these dead-transactionsthe file logical.log always keeps getting bigger in the default-database, thus CADISONkeeps getting slower.These dead transactions can be resolved only when databases of same names are createdand the default database is restarted. Subsequently, databases created temporarily can bedeleted again.This option executes this setp automatically. -RESOLVEDEADTRANSACTIONS can only be executed directly on the server if no otherCADISON work stations have started a CADISON application.The parameter [Log-file] is optional. Here, the name of a file which is to be created can bespecified (including the path). The file is always created anew by this option and theessential specifications are retained.
New option -DELDBSINRB [Log-file]
Databases, which have been stored in so-called recycle bin-database groups can beautomatically deleted with this option. The option is executable only direct on the serverand no CADISON-applications must be active.iAny number of recycle bins can be defined using the entry in CADISON.INI, in section[PHi-CADISON]:[PHi-CADISON]RecycleBinFolder=1 recycle bin;recycle bin department 1;recycle bin department 2
If a database is not reqiured any more, then the CADISON user can move this in to therecycle bin without having to delete it immediatly.These databases are automatically deleted when the new ITFTOOLS-Option is accesse.Thereby it is ensured thatno dead transactions are created in the default database bydeleting a project database.The project folders associated with database are also deleted when the database isdeleted. Likewise the entries in CADISON-Tree are also deleted.The parameter [Log-file] is optional. The name of a log file can be given here (includingthe path). When a name is specified, then DELDBSINRB creates a new log file and recordsall the essential messages. An already existing log file is deleted.
72
ITandFactory GmbH
CADISON R9.0.0 Release Notes
New option -TRANSFERDOCS
After this version, ITFTOOLS offers a new undocumented option. With this option alldocuments of a project can be read or transferred in the database.The syntax of the option is:ITFTOOLS -TRANSFERDOCS <dbname> READITFTOOLS -TRANSFERDOCS <dbname> WRITE
The READ-sub-option reads all documents, the WRITE-sub-option transfers all documents.At the end of the process information containing the number of documents successfullyprocessed, how many had errors and how many were to be omitted based on these errors(e.g. "missing documents", which were not associated with the project).
Function changes
Correction of unused graphical representations
After this version, the correction function of ITFTOOLS (e.g. -xclean) can no longer identifyand delete referred graphical representation, which were not connected other objects fromthe CADISON tree.
73
ITandFactory GmbH
CADISON R9.0.0 Release Notes
API
Bug fixes
Setting of feature values using CADISON API
Till now, no new feature value in case of the object CDSNProperty was set with theCADISON API, if the feature was a unit field with one fixed selection list and a minimumand maximum value. This error is now resolved.
74
ITandFactory GmbH
CADISON R9.0.0 Release Notes
Conclusive Information
The CADISON Hotline is available during the time mentioned below:
Mon. – Thurs. 08:30 bis 17:00 Uhr Fri. 08:30 bis 15:00 Uhr
Telephone: +49 6196 6092-500Fax: +49 6196 6092-202Email: [email protected]
In case of special questions you are welcome to contact our employees.
CADISON Training:
Training officeTelephone: +49 6196 6092-510Fax: +49 6196 6092-202Email: [email protected]
CADISON Sales:
Sales officeTelephone: +49 6196 6092-310Fax: +49 6196 6092-202Email: [email protected]
Further information can be found on our Internet homepage:
www.cadison.com
or contact us at
We wish you great success with CADISON.
Your CADISON-Team
75
ITandFactory GmbH
CADISON R9.0.0 Release Notes
Index
- 3 -3D-Designer 48
- A -ACIS-converter 32Actuator is on incorrect layer 39Allocation of measuring point 36API 73Archiever 33AUTO_DUCTSPEC 48AUTO_PIPESPEC 48, 39
- C -Calculation of the length of screws 48Conclusive information 74Consistency checker 39Consistency test 39Copy 60Cross references 21
- D -Designer general 39Drawings of new pipelines 39
- E -Electric-Designer 51Engineer2Web 68
- F -FILEREFERENCE 34
- G -General 21General 69Graphic entries 60
- I -Invalid characters 21Invalid graphical representations 21ISOGEN 52ISOGEN-module-code ffor screws 52ITFTOOLS 71ITF_DUCT 48
- K -Key word"hasTableOnly" 34
- L -Labeling dialog 39Links 60
76
ITandFactory GmbH
CADISON R9.0.0 Release Notes
- M -Manual counter 39MATPIPE 60MATPIPE 60Memo fields 21Moving of numbers 21
- N -N-Edge incorrectly presented 48
- O -Object locking while report generation 34Object model 36ObjectInspector 39Overview of bug fixes 14
- P -Parametrization dialog box 60Performance optimisation 21PID-Designer 46Project comprehensive copying 21Project-Navigator 67
- R -Reinstallation 4Report generator 34Report-Mappingdatei report.tpm 34Right “create object“ 34
- S -Selector 66Symbol editor 39
- U -Uninstallation 4Use of SelectionMarker '0' in 3D-Elements 48
- V -Ventilation channels 48Versant-Patch 2 21Versions stand of report documents 34Visio PID 54
- W -Windows Vista 39
- X -XREFS 39