Quick release pins LOCKWELL® - PSM Celada pins.pdf · Steel Min per AMS-H-6875; PH 15-7 MO,...

Quick release pinsLOCKWELL®

LOCKWELL®

Securing Success

1

Approved Certification List

LOCKWELL® single & double acting pins are

manufactured to NASM 23460 and NAS

1332 and are approved on the QPL for:

NAS1333 to NAS 1346

NAS 1353 to NAS 1366

NAS 17984 to NAS 17990

Specials

This catalogue illustrates DZUS’ standard

range of LOCKWELL® Quick Release Pins.

Should you require an alternative to the

standard range, our experienced engineering

department is able to design a pin that

incorporates LOCKWELL® quality features to

your specific requirements.

Fastening Solutions for a Global Market

The LOCKWELL® Quick Release Pin range from

DZUS includes positive locking pins, with single or

double action lock release mechanisms, as well as

detent pins, receptacles and other accessories.

Utilised to quickly lock two or more objects

together in applications where a retaining force is

required, LOCKWELL® Quick Release Pins are

excellent alternatives to replace traditional fasteners

such as nuts and bolts, cotter pins, linch pins and

hitch pins in a wide variety of different applications.

LOCKWELL®

Quick Release Pins

2

Securing Success

GRIP LENGTH

Grip Length

This is the load bearing area on the LOCKWELL® quick release pin and is measured from shoulder

to the tangent point where the ball intersects the shank diameter.

Grip length for Lockwell pins is always specified in thousandth-inch increments,

e.g. a grip length of 500 in a LOCKWELL® pin part number equals 1/2” grip length.

Drive-Out Feature

Single and double acting pins are available with the drive-out feature shown here.

This feature is employed where removal of the pin is necessary while in a shear loaded condition.

To order the drive-out feature, insert a ‘D’ after the grip length – see ‘Example of Part numbers’

on page 6.

Four-Ball Pins

Four-ball pins are used when the user requires greater tension strength than that offered by the

standard two-ball single and double acting pins. The minimum tension load capabilities can be

seen in the ‘Loads and Hole Diameters’ table below.

Loads and Hole Diameters

MINIMUM TENSION LOADSACTUAL RECOMMENDED CAPABILITIES (b)

DIA. NOM. FINISH DIA. HOLE DIA. (a) BALL 2 BALL 4 BALLDASH NO. DIA. MAX. MIN. MAX. MIN. DIA. CONST. CONST.

3 3/16” .1885 .1870 .194 .190 .062(1/16) 200 lbs 260 lbs4 1/4” .2485 .2470 .254 .250 .093(3/32) 230 lbs 290 lbs5 5/16” .3110 .3095 .3165 .3125 .125(1/8) 510 lbs 630 lbs6 3/8” .3735 .3720 .379 .375 .140(9/64) 575 lbs 740 lbs7 7/16” .4360 .4345 .4425 .4375 .156(5/32) 710 lbs 920 lbs8 1/2” .4985 .4970 .505 .500 .187(3/16) 1160 lbs 1500 lbs9 9/16” .5610 .5595 .5675 .5625 .218(7/32) 1420 lbs 1840 lbs

10 5/8” .6235 .6220 .630 .625 .250(1/4) 2070 lbs 2690 lbs12 3/4” .7485 .7470 .757 .750 .281(9/32) 2950 lbs 5070 lbs14 7/8” .8735 .8720 .882 .875 .343(11/32) 3900 lbs 5070 lbs16 1” .9985 .9970 1.010 1.000 .406(13/32) 5480 lbs 7120 lbs

(a) REF NAS 618 (b) REF NASM 23460

In tutto i l mondo si chiamano fasteners, in Italia si chiamano PSM Celada

LOCKWELL®

Single Acting Pins – LG Series

3

Materials and SpecificationsPART ALLOY STEEL CORROSION RESISTANT

Shank and Spindle 4130 Steel per AMS 6360 or AMS-S-6758 17-4 PH CRES per AMS 5643 or equivalent

Balls 440C CRES per AMS-QQ-S-763, Rc 58-62 440C CRES per AMS-QQ-S-763, Rc 58-62

Button Carbon steel per ASTM A 108 or 2024 ALUM Alloy per AMS-QQ-225/6 303 CRES per ASTM A581/582 or 2024 ALUM Alloy per AMS-QQ-225/6

‘B’ Button Handle Carbon steel per ASTM A 108 or 2024 ALUM Alloy per AMS-QQ-A-225/6 303 CRES per AMS 5640 or 2024 ALUM Alloy per AMS-QQ-A-225/6

‘T’ Handle ALUM alloy casting per ASTM B85 or ALUM extrusion 6061-T6 per ALUM alloy casting per ASTM B85 or ALUM extrusion 6061-T6 perAMS-QQ-A-200/8 AMS-QQ-A-200/8

‘L’ Handle ALUM alloy casting per ASTM B85 or ALUM extrusion 6061-T6 per ALUM alloy casting per ASTM B85 or ALUM extrusion 6061-T6 perAMS-QQ-A-200/8 AMS-QQ-A-200/8

‘R’ Handle Ring Music wire per ASTM A228 302 CRES per ASTM A313

‘R’ Handle (head) Carbon steel per ASTM A108 or 2024 ALUM Alloy per AMS-QQ-A-225/6 303 CRES per AMS 5640 or 2024 ALUM Alloy per AMS-QQ-A-225/6

Washer ‘T’ & ‘L’ Handles Carbon steel per ASTM A366 301/302/304 CRES per ASTM A240

Spring Music wire per ASTM A228 302 CRES per ASTM A313

Attaching Link Hard drawn carbon wire per ASTM A227 or 302 CRES per ASTM A313 302 CRES per ASTM A313 or hard drawn carbon wire per ASTM A227

HEAT TREATMENT PROTECTIVE TREATMENT

Alloy Steel Shank and spindle 160,000/180,000 PSI Carbon and Alloy Steel Cadmium plate per AMS-QQ-P-416, Typeper AMS-H-6875

Corrosion Resistant Shank and spindle 17-4-PH, 190,000 PSI Corrosion Resistant Steel Passivate per ASTM A 967Steel Min per AMS-H-6875; PH 15-7 MO, 180,000 PSI

Min per AMS-H-6875 Aluminium Alloy Anodise per AMS-A-8625

LG Series Dimensions

PIN NOM A B C D E F G H J K L M N P R S T U DOUBLE SHEARNO. DIA. MAX. MIN. ±.005 MAX. MIN. MIN. MAX. MAX. MIN. MAX. MIN. MIN. MAX. MIN. MIN. MAX. MIN. MIN. MIN. STL CRES

3 3/16 .1885 .1870 .220 .260 .250 .310 1.815 1.270 .800 1.800 .760 .730 1.450 1.060 .480 .830 .720 .105 .380 4,600 5,1504 1/4 .2485 .2470 .289 .290 .250 .310 1.815 1.270 .800 1.800 .760 .780 1.500 1.060 .480 .890 .720 .105 .380 8,200 9,2005 5/16 .3110 .3095 .375 .330 .250 .410 1.815 1.270 .800 1.800 .760 .830 1.650 1.060 .480 .930 .810 .105 .380 12,800 14,4006 3/8 .3735 .3720 .440 .365 .300 .450 2.065 1.450 .850 2.030 .850 .940 1.650 1.060 .620 1.040 .875 .134 .510 18,400 20,6007 7/16 .4360 .4345 .509 .380 .300 .550 2.065 1.470 .850 2.030 .850 .980 1.850 1.090 .620 1.160 .940 .134 .510 25,000 28,0008 1/2 .4985 .4970 .594 .460 .435 .600 2.345 1.600 .885 2.360 .850 1.140 1.850 1.160 .720 1.190 1.300 .200 .630 32,800 36,8009 9/16 .5610 .5595 .666 .510 .435 .680 2.345 1.600 .885 2.360 .850 1.140 2.030 1.160 .950 1.410 1.340 .200 .630 41,200 46,000

10 5/8 .6235 .6220 .750 .580 .450 .750 3.100 1.700 .980 3.070 .905 1.400 2.250 1.240 .950 1.500 1.530 .231 .810 51,200 57,50012 3/4 .7485 .7470 .887 .670 .570 .865 3.100 1.720 1.030 3.070 .980 1.625 2.650 1.640 1.140 1.680 1.790 .231 .810 73,600 82,50014 7/8 .8735 .8720 1.046 .760 .700 .980 3.520 2.170 1.310 3.700 1.200 1.875 3.000 1.640 1.270 1.985 2.120 .231 1.120 100,000 112,50016 1 .9985 .9970 1.219 .890 .750 1.175 3.520 2.170 1.310 3.700 1.200 2.000 3.100 1.640 1.490 2.140 2.120 .231 1.180 131,000 147,000

LG Series

Positive locking pins, providing operational security, with a simple push button for quick release.

Multi-purpose pins, available in a wide range of handle styles and sizes to suit a massive range

of different application requirements.

Typical Applications

Aerospace (equipment mounting, seating, safety locking mechanism, ground support equipment)

Industrial (tool fixtures, trolleys and hoists, testing fixtures)

Construction (scaffolding, ladders, fencing)

Motorsport (panel fastening, pit equipment, shock absorbers)

Marine (rigging, equipment mounting)

Dettagli tecnici completi sono disponibili sul sito internet www.psmcelada.it

LOCKWELL®

Single Acting Pins – LG Series

4

Securing Success

HANDLESTYLE

T

HANDLESTYLE

LB

TB

L

R

B

Notes

1. All pins meet or exceed the requirements of procurement specifications NASM 23460, and/or NAS 1332 and are QPL listed on NASM 17984 to 17987

and NAS 1333 to 1346.

2. Attaching links standard on all pins.

3. Button ‘B’ handle available in aluminium (‘A’) or CRES (‘C’) on pins with CRES shank.

4. If a four-ball pin is required for greater tension strength, add the suffix ‘F’ at the end of standard callout. (See chart for tension loads).

5. If greater ‘C’ dimension is necessary, add length in thousandth of an inch after ‘F’ letter. Example: LG3CT300F750 (750 = .750 inch)

6. Pins are identified per AMS-STD-130 and applicable specification.

7. Single acting pins are available in metric sizes. Specify when ordering.

8. Extruded and cast ‘T’ and ‘L’ handles share the same envelope dimensions.

Example of Part Numbers

LONGER NON STANDARD ‘C’ DIM. SEE NOTES. OMIT FOR STANDARD ‘C’ DIM.

USED WHEN MANUFACTURED TO MS OR NASM.

‘F’ –4 BALL CONSTRUCTION. ‘S’ – SINGLE BALL CONSTRUCTION. OMIT FOR STANDARD 2 BALL PIN

GRIP LENGTH (THOUSANDTH INCH INCREMENTS)

HANDLE STYLE: SEE DIAGRAM

MATERIAL ‘S’ ALLOY STEEL ‘C’ COR. RES. STEEL

SHANK DIAMETER: SEE CHART

LOCKWELL SINGLE ACTING PIN

LG 3 C T 300 F M 750


LOCKWELL®

Double Acting Pins – LH Series

5

LH Series Dimensions

PIN NOM. DOUBLE SHEARNO. DIA. MAX. MIN. ±.005 MAX. MAX. MIN. MAX. MAX. MAX. MIN. MAX. MAX. MAX. MIN. MIN. MIN. STL CRES

3 3/16 .1885 .1870 .220 .410 .450 .935 .480 1.945 1.125 .780 1.300 .50 1.030 1.375 .105 .080 4,600 5,1504 1/4 .2485 .2470 .289 .410 .450 .935 .480 1.945 1.125 .780 1.300 .50 1.030 1.375 .105 .080 8,200 9,2005 5/16 .3110 .3095 .375 .440 .505 .935 .480 1.945 1.125 .780 1.300 .55 1.030 1.375 .105 .080 12,800 14,4006 3/8 .3735 .3720 .440 .510 .630 1.000 .540 2.025 1.125 .830 1.500 .64 1.090 1.875 .134 .080 18,400 20,6007 7/16 .4360 .4345 .509 .510 .630 1.000 .540 2.025 1.125 .830 1.500 .64 1.090 1.875 .134 .080 25,000 28,0008 1/2 .4985 .4970 .594 .590 .755 1.070 .540 2.060 1.125 .880 1.655 .75 1.270 2.125 .200 .080 32,800 36,8009 9/16 .5610 .5595 .666 .660 .755 1.070 .540 2.060 1.125 .880 1.655 .82 1.270 2.125 .200 .080 41,200 46,00010 5/8 .6235 .6220 .750 .750 .870 1.250 .575 2.550 1.500 1.000 1.810 .93 1.465 2.375 .231 .120 51,200 57,50012 3/4 .7485 .7470 .887 .790 .960 1.250 .595 2.550 1.500 1.000 1.810 .97 1.465 2.375 .231 .120 73,600 82,50014 7/8 .8735 .8720 1.046 .950 1.150 1.500 .730 2.770 1.500 1.180 2.250 1.18 1.640 2.750 .231 .120 100,000 112,50016 1 .9985 .9970 1.219 1.100 1.280 1.700 .865 2.950 1.500 1.320 2.250 1.35 1.830 2.750 .231 .120 131,000 147,000

A B C D E F G H J K L M N P R

Materials and Specifications

PART ALLOY STEEL CORROSION RESISTANT

Shank and Spindle 4130 Alloy steel per AMS 6360 & AMS-S-6758 Corrosion resistant steel 17-4 per AMS 5643 or equivalent

Balls Corrosion resistant steel 440-C Corrosion resistant steel 440-C

per AMS-QQ-S-763, Rc 58-62 per AMS-QQ-S-763, Rc 58-62

Button Carbon steel per ASTM A108 Corrosion resistant steel 303 per AMS 5640

Handle Carbon steel per ASTM A108 Corrosion resistant steel 303 per AMS 5640

Handle Ring Corrosion resistant steel 302 per ASTM A313 Corrosion resistant steel 302 per ASTM A313

or music wire per ASTM A228

Spring Music wire per ASTM A228 Corrosion resistant steel 302 per ASTM A313

Attaching Link Carbon steel wire per ASTM A227 or corrosion resistant Corrosion resistant steel 302 per ASTM A313

steel 302 per ASTM A313

HEAT TREATMENT PROTECTIVE TREATMENT

Alloy Steel Shank and spindle 160,000/180,000 PSI Carbon and Alloy Steel Cadmium plate per AMS-QQ-P-416, Type II, Class 2

per AMS-H-6875

Corrosion Resistant Shank and spindle 17-4-PH, 190,000 PSI Corrosion Resistant Steel Passivate per ASTM A967

Min. per AMS-H-6875; PH 15-7 MO, 180,000 PSI

Min. per AMS-H-6875 Aluminium Alloy Anodise per AMS-A-8625

LH Series

Positive locking pins with a push-pull button for release. Available in 3 different handle styles to suit a range

of applications, with the double acting mechanism providing increased flexibility for the user.


Aerospace (engine cowling, ground support equipment, safety locking mechanism, equipment mounting)

Motorsport (pit equipment, shock absorbers)


LOCKWELL®

Double Acting Pins – LH Series

6

Securing Success

L

HANDLESTYLE

R

HANDLESTYLE

T


LONGER NON STANDARD ‘C’ DIM. SEE NOTES. OMIT FOR STD ‘C’ DIM.

USED WHEN MANUFACTURED TO MS OR NASM.

‘F’ 4 BALL CONSTRUCTION. OMIT FOR 2 BALL PIN.

‘N’ –NON DRIVE OUT. ‘D’ –DRIVE OUT

GRIP LENGTH (THOUSANDTH INCH INCREMENTS)


MATERIAL: ‘S’ ALLOY STEEL, ‘C’ COR. RES. STEEL

SHANK DIAMETER: SEE CHART

LOCKWELL DOUBLE ACTING PIN

LH 3 C T 300 D F M 750

Notes

1. All pins meet or exceed the requirements of procurement specifications NASM 23460 and are QPL listed on NASM 17988 to NASM 17990

and NAS 1353 to 1366.

2. Attaching links standard on all pins.

3. Double acting pins are available with drive-out feature. This feature is employed where removal of pin is necessary while in a shear loaded condition. To order

drive-out, see part number example.

4. If a four-ball pin is required for greater tension strength, add the suffix ‘F’ at the end of standard callout. (See chart for tension loads)

5. If greater ‘C’ dimension is necessary, add length in thousandth inch increments after ‘F’ letter. Example: LH3CT300DF750 (750=.750 inch)

6. Pins are identified per AMS-STD-130 and applicable specification.

7. Double acting pins are available in metric sizes. Specify when ordering.


LOCKWELL®

Detent Pins – LA and LJ Series

7

*Not available in LJ SeriesShear values based on 60% of ultimate tensile

strength of material.

*Not available in LJ Series

PINNO. S C B D

*3 2,640 2,970 1,155 1,6504 4,598 5,173 2,012 2,8745 7,200 8,100 3,150 4,5006 10,435 11,740 4,565 6,5227 14,198 15,973 6,212 8,8748 18,624 20,952 8,148 11,6409 23,558 26,503 10,307 14,72410 29,174 32,821 12,764 18,23412 42,077 47,336 18,409 26,29814 57,331 64,498 25,082 35,83216 74,947 84,316 32,789 46,842

CALCULATED SINGLE SHEAR(POUNDS)

LA, LJ and LR Series Materials and Specific

PART ALLOY STEELShank 4130 Steel per AMS-S-6758

12L14 & 1215 Steel per ASTM A108Head 12L14 & 1215 Steel per ASTM A108

4130 Steel per AMS-S-6758

Handle/Ring 303 CRES per AMS 5640Hard drawn carbon wire per ASTM A227

Balls 440C CRES per AMS-QQ-S-763, Rc 58-62Springs 17-7 PH CRES per AMS 5678,

Music wire per ASTM A228Finish All steel parts cadmium plated per

AMS-QQ-P-416

LA and LJ Series Dimensions

NOM A B C D E F G H J K L M N P SPIN SHANK +.0000NO. DIA. - .0015 ± .010 MAX. ± .010 MAX. MAX. ± .030 ± .010 ± .030 ± .010 MIN. ± .030 ± .060 ± .010 MAX.*3 3/16 .1885 .213 .219 .312 .562 1.18 .75 .062 1.875 .188 .500 1.188 1.000 .375 .184 1/4 .2485 .280 .282 .375 .562 1.34 .75 .062 1.875 .188 .500 1.188 1.000 .375 .255 5/16 .3110 .350 .343 .438 .562 1.20 .75 .062 2.000 .188 .500 1.500 1.000 .500 .256 3/8 .3735 .421 .391 .500 .562 1.41 1.00 .062 2.000 .188 .500 1.500 1.000 .500 .257 7/16 .4360 .491 .436 .563 .562 1.61 1.00 .062 2.125 .250 .750 1.563 1.000 .625 .258 1/2 .4985 .562 .500 .625 .562 1.38 1.00 .062 2.125 .250 .750 1.563 1.000 .625 .319 9/16 .5610 .631 .562 .688 .562 1.98 1.50 .105 2.188 .250 .750 1.594 1.500 .688 .3110 5/8 .6235 .702 .624 .750 .562 2.01 1.50 .105 2.250 .312 .810 1.875 1.500 .750 .3712 3/4 .7485 .843 .718 .875 .562 2.00 1.50 .105 2.375 .312 .810 1.938 2.000 .875 .3714 7/8 .8735 .983 .843 1.000 .562 2.50 2.00 .105 2.500 .312 .840 2.000 2.000 1.000 .5016 1 .9985 1.124 .968 1.125 .562 2.41 2.00 .105 2.625 .312 .840 2.063 2.000 1.125 .50

LA and LJ Series

LA and LJ Series Detent Pins are engineered and manufactured to Aerospace/Military tolerances.

The LJ Series features an exclusive two ball construction for added strength. All other specifications

and dimensions are the same.


Aerospace (equipment mounting, aircraft cabin interiors)

AEROSPACE/MILITARY


GRIP LENGTH–IN THOUSANDTHS (.375 GRIP)


PIN MATERIAL: ‘S’ 4130 STEEL‘C’ 17-4PH COR. RES. STEEL‘B’ 12L14-1215 STEEL‘D’ TYPE 302/304 COR. RES. STEEL

SHANK DIAMETER–SEE CHART *NOT AVAILABLE IN LJ SERIES

LOCKWELL DETENT PIN‘LA’ SINGLE BALL CONSTRUCTION‘LJ’ 2 BALL CONSTRUCTION

LA 4 S T 375

HANDLESTYLE

W R T L


LOCKWELL®

Detent Pins – LR Series

8

Securing Success

ations

CORROSION RESISTANT STEEL17-4 PH CRES per AMS 5643304 CRES per AMS-QQ-S-763303 CRES per AMS 564017-4 PH CRES per AMS 5643 or304 CRES per AMS-QQ-S-763300 series CRES per ASTM A313 or AMS 5640

440 CRES per AMS-QQ-S-763, Rc 58-6217-7 PH CRES per AMS 5678,Music wire per ASTM A228All CRES parts passivated per ASTM A96

PINNO. D E F

3 1,283 2,555 1,1184 2,299 4,585 2,0055 3,611 7,203 3,1516 5,216 10,411 4,5557 7,117 14,208 6,2168 9,312 18,594 8,1349 11,801 23,568 10,31110 14,485 29,132 12,74512 21,036 42,027 18,38714 28,665 57,279 25,05916 37,473 74,886 332,762

CALCULATED SINGLE SHEAR(POUNDS)

LR Series Dimensions

NOM A B C D E F G H J KPIN SHANK +.000 + .020NO. DIA. - .003 ± .010 MAX. - .030 MAX. DIA. DIA. DIA. ± .060

3 3/16 .1875 .200 .200 .750 .339 .096 1.25 .093 .062 .8754 1/4 .2500 .286 .312 .750 .401 .128 1.25 .125 .062 .8755 5/16 .3125 .358 .375 .750 .464 .159 1.25 .156 .062 .8756 3/8 .3750 .426 .500 .750 .589 .159 1.75 .156 .062 .8757 7/16 .4375 .496 .562 1.000 .652 .159 1.75 .156 .062 .8758 1/2 .5000 .570 .625 1.062 .714 .191 2.00 .188 .105 1.0409 9/16 .5625 .642 .687 1.062 .776 .191 2.00 .188 .105 1.040

10 5/8 .6250 .710 .750 1.125 .870 .253 2.25 .250 .105 1.04012 3/4 .7500 .856 .937 1.375 .994 .253 2.25 .250 .105 1.29014 7/8 .8750 .996 1.000 1.500 1.009 .379 2.50 .375 .105 1.29016 1 1.0000 1.140 1.250 1.500 1.244 .379 2.50 .375 .105 1.290

COMMERCIAL

LR Series

LR Series Detent Pins are the cost effective answer for Commercial/Industrial applications requiring

conventional tolerances in manufacturing and installations. LR Series Detent Pins are one ball construction.



Motorsport (panel fastening, pit equipment)

Marine (rigging, equipment mounting, panel fastening)


LOCKWELL DETENT PIN

SHANK DIAMETER–SEE CHART

PIN MATERIAL:‘D’ TYPE 303 COR. RES. STEEL

‘E’ 4130 STEEL (TYPE I CAD. PLATE)‘F’ 12L14/1215 STEEL (TYPE I CAD. PLATE)

HANDLE STYLE–SEE DIAGRAM

GRIP LENGTH-IN THOUSANDS (1,500 GRIP)

LR 3 D T 1500

Shear values based on 60% of ultimate tensile strength of material.

HANDLESTYLE

X L T R N


LOCKWELL®

Detent Pins – LC Series

9

F D

E

A B C

LC Series

A low cost alternative, especially suited for general industrial and commercial applications.

It comes in only one handle style, which is suitable for many different applications.

Typical Application

Health and Fitness (weight training equipment)


LC Series Dimensions

PART NO. DIA. MIN. DIA. MAX. REF. GRIP+ .000 ±.015 + .020– .003 – .000

LC 405 .500LC 4075 .750LC 410 1.000LC 4125 .2480 .280 .375 .344 .07 1.250LC 415 1.500LC 420 2.000LC 425 2.500LC 430 3.000LC 5075 .750LC 510 1.000LC 5125 1.250LC 515 1.500LC 520 .3105 .360 .438 .359 .10 2.000LC 525 2.500LC 530 3.000LC 535 3.500LC 540 4.000LC 610 1.000LC 6125 1.250LC 615 1.500LC 620 2.000LC 625 .3730 .430 .500 .390 .12 2.500LC 630 3.000LC 635 3.500LC 640 4.000LC 645 4.500LC 810 1.000LC 820 2.000LC 825 2.500LC 830 .4980 .570 .625 .516 .17 3.000LC 840 4.000LC 850 5.000

A B C D E F

Notes

1. Grip length measured to edge of ball hole prior to staking.

2. Angular position of balls with respect to handle may vary.

3. Material: All CRES and passivated.

HANDLESTYLE

W


LOCKWELL®

Quick Release Pins – Accessories

10

Securing Success

Lanyards

LOCKWELL® lanyards and chain assemblies keep the quick release pins permanently attached to the

installation. Materials include stainless steel, alloy steel and cold rolled steel. Lanyards may be purchased

separately or assembled to your pin at no extra cost.

LW1023 : Lanyard with tab

LW1036 : Lanyard without tab

LW1145 : Chain assembly with option of tab & link

Streamers

LOCKWELL® streamers flag critical applications and may be purchased separately or pre-assembled to

Lockwell pins. Call us today with your requirements.

Receptacles

LOCKWELL® receptacles assure an instant positive lock for quick release pins. Ideal for blind applications

and installations when the pin needs a hardened surface for the balls to lock against. They are available in a

variety of styles, sizes and mounting methods. Skin thicknesses of .032” to .500” are standard.

Features include: Spring loaded, dust/weather seal and spring-assisted uncoupling.

Materials and Specification

Cable: Corrosion resistant steel per MIL-DTL-83420 – 1/16 Dia. 7 x 7. Rated full strength: 480 lbs.

Coating: Available bare or vinyl coated (red, green, black, clear per MIL-I-631, Type F, Grade A, Class II, Cat. 1).

Chain: #1 safety chain, cold rolled steel, Cad plated – supplied in .050 inch increments (± .25 in.)

Sleeve: Copper, zinc plated

Link: CRES of hard drawn carbon wire ASTM A313 ASTM A227

TAB: 2024-T4 Aluminum, per AMS-QQ-A-250/4

Anodised per AMS-A-8625, Type 1A, Class 1

LW 1023 LW 1036 LW 1145


Altri prodotti PSM CELADA FASTENERS:

Fasteners per Materie Plastiche Inserti Filettati SONIC-LOK ® TECH-SONIC ® MINI-TECH ® PRESS-LOK ® FIN-LOK ® HEAT-LOK ® SPIRO ® BANC-LOK ® FLO-TECH ® ELISERT ® SCREW-SERT ® SERINSERT ® WOOD-SERT ® SERBOIS ®

Viti Autofilettanti Tipo “PT ®”, “Delta PT ®” e “Duro PT ®”

Fasteners per Lamiere Sottili Dadi autoaggancianti PS ® Prigionieri autoaggancianti PFH ® Inserti autoaggancianti PF Distanziatori autoaggancianti PTSO/PBSO RivettifilettatiRIVEBLOC® RivettiantivibrantiRIVEBLOC® RUBBER Dadi in gabbia KLIPNUT ® Vitiimperdibili Inserti a ribadire ANCORA ®

Fasteners per Circuiti Stampati DadieDistanzialifilettatiautobrocciantiPCBR®/SCBR ® DistanziatorimobiliSPA

Fasteners per Leghe Leggere e Metalli Filetti riportati ELICEL ® Dadi autofrenanti ELIBLOC ® BoccoleautofilettantiSCREW-SERT® Inserti autobroccianti PHI Spine intagliate VitiautofilettantiTipo“PT® - DG” Guarnizione per vite NYLTITE ® InsertifilettatiadaltaresistenzaKEENSERTS®

Fissaggi Rapidi SoluzionidifissaggioSOUTHCO® Chiusure rapide a 1/4 di giro DZUS ® Fissaggi rapidi in plastica NYLATCH ® Chiusure HARTWELL ® Spine a sgancio rapido LOCKWELL ® Cerniere a controllo costante CEMA ® Dispositivi di accesso per la nautica MOBELLA ®

Attrezzature per il montaggio Macchineperl'inserimentoautomaticoHAEGER®

Distributore

La Società

L’attività nel settore dei fasteners

inizia nel 1954 all’interno del gruppo

R.F. CELADA che già da allora

operava con successo nel settore

della meccanica. Grande importanza

rappresentò all’epoca la distribuzione

esclusiva per l’Italia del filetto

riportato Heli-Coil.

L’espansione dell’attività porta

alla creazione nel 1975 della

CELADA FASTENERS,

che grazie alla validità degli articoli

proposti ed alla sempre maggiore

affermazione sul mercato nazionale,

permette la nascita, nel 1986

di PSM CELADA FASTENERS,

in Joint-Venture con il

gruppo multinazionale PSM

INTERNATIONAL.

Oggi la PSM CELADA FASTENERS è

un’azienda leader nella distribuzione

di sistemi di fissaggio innovativi,

chiusure rapide ed attrezzature per

l’assemblaggio, presente su tutto il

territorio nazionale.

Certificazione

UNI EN ISO 9000: 2000

GPL/V2-0109

PSM Celada Fasteners

CONNECT · CREATE · INNOVATE

ViaPorpora,24-20131MilanoTel.0229400630Fax 02 2951 [email protected]

Quick release pins LOCKWELL® - PSM Celada pins.pdf · Steel Min per AMS-H-6875; PH 15-7 MO,...

Documents

Transcript of Quick release pins LOCKWELL® - PSM Celada pins.pdf · Steel Min per AMS-H-6875; PH 15-7 MO,...