8/11/2019 Quick Guide Samsung CCTV

1/2

Installation Precautions

CCTV equipment must be installed by an experienced service engineer.

Install the camera at a location that can support more than 4 times the total weightof the equipment.

Install the camera at a location free from mechanical vibration. When installing at alocation subject to mechanical vibration, be sure to install anti-vibration measuresbefore putting the camera in position.

Contents

Protection Against Lightning Strikes

Waterproof Installation

At a Glance

Connecting the adaptor cable

Cable Connection

Communication Setup

1. Protection Against Lightning Strikes

For outdoor installations, a lightning rod must be installed above the camera toprotect it from lightning strikes.

To avoid interference and prevent damage due to current surges, the camera'sgrounding conductor must be separate from the lightning arrester's ground andhigh-voltage ground.

Caution

Lightning generates great amounts of energy so that lightning rods cannot guarantee totalprotection for the camera.

When installing a lightning rod, make sure that protection angle and minimum distance (2m)between the lightning rod and the camera are properly implemented.

1.

2.

3.

1.

2.

3.

4.

5.

6.

1.

2.

2. Waterproof Installation

Precautions for waterproofing when installing the camera on the wall with acombination of OUTDOOR HOUSING and WALL MOUNT ADAPTOR.

Install the WALL MOUNT on a vertical wall. Installation on a tilt wall may cause inflow of

moisture into the OUTDOOR HOUSING through the external cables.

Apply the sufficient TEFLON TAPE to the screws (1.5 NPT) present in the HOUSING BODY.

Connect the external cables through the BUSH to the HOUSING BODY.

(For more information about the connection, refer to the user manual of the OUTDOOR

HOUSING.)

When mounting the COVER DOME onto the HOUSING BODY, note that you should not

let the GASKET DOME loose from the COVER DOME. Also keep in mind that the O-RING

for each SCREW (x3) should not be loose from the SCREW while fixing the SCREW.

For waterproofing purposes, after inserting the WALL MOUNT ADAPTOR, apply the

SILICON SEALANT between the wall and WALL MOUNT, and around the borders.

(Pay special attention to the sealing when installing on an irregular surface.)

1.

A.

B.

C.

D.

E.

Precautions for waterproofing when installing the camera on the wall with acombination of OUTDOOR HOUSING and CEILING MOUNT ADAPTOR.

Apply the sufficient TEFLON TAPE to the screws (1.5 NPT) present in the HOUSING BODY.

Connect the external cables through the BUSH onto the HOUSING BODY.

(For more information about the connection, refer to the user manual of the OUTDOOR

HOUSING.)

When mounting the COVER DOME onto the HOUSING BODY, note that you should not

let the GASKET DOME loose from the COVER DOME. Also keep in mind that the O-RING

for each SCREW (x3) should not be loose from the SCREW while fixing the SCREW.

For waterproofing purposes, after inserting the CEILING MOUNT ADAPTOR, apply the

SILICON SEALANT between the wall and WALL MOUNT, and around the borders.

(Pay special attention to the sealing when installing on an irregular surface.)

2.

A.

B.

C.

D.

(Protection Angle a : Within 45) (Minimum height of the lightning rod)

Min. 2m

WALL MOUNT

BUSH

1.5 NPT PIPE

COVER DOME SCREW

O-RING

HOUSING BODY

GASKET DOME

USE TEFLON TAPE

SILICON SEALANT

CONCRETE WALL

CONCRETE CEILING

CEILING BOARD

SILICON SEALANT

CEILING MOUNT ADAPTOR

BUSH

1.5 NPT PIPE

COVER DOMESCREW

O-RING

HOUSING BODY

GASKET DOME

USE TEFLON TAPE

SCP-3250H

SCP-2250H

SCP-2430H

SCP-3430H

Installation GuideSmart Dome Camera

imaginethe possibilitiesThanks you for purchasing this Samsung product.

To receive a more complete service, please visit

our website

www.samsungsecurity.com

8/11/2019 Quick Guide Samsung CCTV

2/2

4. Connecting the adaptor cable

5. Cable Connection

Power Cable

The following table shows maximum distances allowed for 24VAC applications witha 10% voltage drop. (10%: The maximum value allowed for AC voltage equipment)

WirePowerConsumption

AWG #22 AWG #20 AWG #18 AWG #16 AWG #14 AWG #12 AWG #10

30 vA(indoor)

57ft(17m)

94ft(28m)

150ft(45m)

238ft(72m)

380ft(115m)

603ft(183m)

960ft(292m)

75 vA(outdoor)

25ft(7m)

37ft(11m)

60ft(18m)

95ft(29m)

152ft(46m)

241ft(73m)

384ft(117m)

Communication Cable

Cable requirements for RS-485 communication are as follows:- Shielded Twisted Pair (STP) Cable- Low Impedance

- Gauge greater than AWG #22 (0.33mm

2

)

6. Communication Setup

Camera Address Setup

Use SW606, SW605, and SW604 to specify the camera address.You can specify between 0 and 255 for the address, where the hundreds digit iswith SW606, the tens digit with SW605, and the ones digit with SW604.ex) Camera address: If the address is 1, follow the steps in the figure below.

1.

2.

1.

Single pair

Insulating outer cover

Multicore

Adaptor Board

SW606(x100)

SW605(x10)

SW604(x1)

Baud Rate SetupUse pins #5, #6 of SW603 to set the baud rate.

BAUD RATE PIN 5 PIN 6

4800 BPS ON ON

9600 BPS OFF ON

19200 BPS ON OFF

38400 BPS OFF OFF

The factory default is 9600 BPS.

Caution

The above PIN setting is available only for Samsung protocols.

Termination

If a number of cameras are connected in a daisy chain* configuration as shown inthe connection diagrams below, the last camera must be RS-485 terminated byusing Rx and Tx. (*Daisy Chain: A daisy chain is a means of connecting a number ofdevices to each other in series. For example, Camera 1 is connected to Camera 2,and Camera 2 is connected to Camera 3, and so on.)

Communication Rx Tx

RS-485 Half Duplex ON OFF

RS-422A/RS485 Full Duplex ON ON

Connection Diagrams

Although you can connect up to 128 cameras, connecting less than 32 camerasensures the best communication environment.

A communication error may occur if you connect multiple cameras that are assignedthe same address in the network.

2.

3.

M

Rx(-) Rx(+)CAM 1

Data(+)

Data(-)

CONTROLLER

Rx(-) Rx(+)CAM 2

Rx(-) Rx(+)CAM n-1

Rx(-) Rx(+)CAM n

T x( -) Tx (+ ) R x( -) Rx (+ ) T x( -) T x( +) Rx (- ) R x( +) T x( -) Tx (+ ) R x( -) Rx (+ ) T x( -) Tx (+ ) R x( -) Rx (+ )

CAM 1

Tx +

Tx -Rx +Rx -

CONTROLLER

CAM 2 CAM n-1 CAM n

3. At a Glance

CAMERA

FRAME SET

Wipe out a dirty surface of the lens softly with a lens tissue or cloth to which youhave applied ethanol.M

ALARM IN

POWER INPUT

RS-485

ALARM OUT

LENS

HOOK

HOOK