Quality, Health, Safety and Environment Policy Quality Approvals • Declaration of Conformity
28
www.mann-tek.com Quality, Health, Safety and Environment Policy Quality Approvals • Declaration of Conformity Product Approvals September 2004 EUROPEAN BASIC ACRYLIC MONOMER GROUP (EBAM) Dry Disconnect Couplings for Acrylic Materials Service Industry Recommendation In their drive to improve the health and environment standards in the acrylic materials distribution chain, member companies of the European Basic Acrylic Monomers Sector Group are recommending the use of dry disconnect couplings on the transport equipment for bulk shipments of acrylic acid, methyl acrylate, ethyl acrylate, butyl acrylates and 2-ethyl hexyl acrylate. Caution needs to be exercised when connecting the fixed and mobile parts of couplings from different manufacturers. Compatibility information is available in the EBAM document entitled “Use of dry disconnect couplings on transportation equipment for acrylic monomers service”, which can be downloaded from the following address: http://www.petrochemistry.net/templates/shwArticle.asp?TID=5&SNID=22&AID=43 Rail tank cars, road tank vehicles and portable tanks used for these acrylic monomers need to be equipped with either 2” or 3” couplings. The connecting nozzle could be designed according to the November 1994 NATO standard. Couplings manufacturers must also show that they have introduced an ISO 9000 quality assurance system. The recommendation is given to the best of the EBAM member company ies’ knowledge, and is made without any guarantee as the conditions of use are beyond the industry's control. Neither Cefic nor any member of the Cefic EBAM sector group shall have any liability whatsoever for any decision based on this recommendation. Approvals Version: 120227
Transcript of Quality, Health, Safety and Environment Policy Quality Approvals • Declaration of Conformity
ww
w.m
ann-
tek.
com
Quality, Health, Safety and Environment Policy Quality Approvals • Declaration of Conformity Product Approvals
September 2004
EUROPEAN BASIC ACRYLIC MONOMER GROUP (EBAM)
Dry Disconnect Couplings for Acrylic Materials Service
Industry Recommendation
In their drive to improve the health and environment standards in the
acrylic materials distribution chain, member companies of the European
Basic Acrylic Monomers Sector Group are recommending the use of dry
disconnect couplings on the transport equipment for bulk shipments of
acrylic acid, methyl acrylate, ethyl acrylate, butyl acrylates and
2-ethyl hexyl acrylate.
Caution needs to be exercised when connecting the fixed and mobile
parts of couplings from different manufacturers. Compatibility information
is available in the EBAM document entitled “Use of dry disconnect
couplings on transportation equipment for acrylic monomers service”,
which can be downloaded from the following address:
http://www.petrochemistry.net/templates/shwArticle.asp?TID=5&SNID=22&AID=43
Rail tank cars, road tank vehicles and portable tanks used for these
acrylic monomers need to be equipped with either 2” or 3” couplings.
The connecting nozzle could be designed according to the November
1994 NATO standard. Couplings manufacturers must also show that
they have introduced an ISO 9000 quality assurance system.
The recommendation is given to the best of the EBAM member company ies’ knowledge, and is made without
any guarantee as the conditions of use are beyond the industry's control. Neither Cefic nor any member of the
Cefic EBAM sector group shall have any liability whatsoever for any decision based on this recommendation.
Approvals Version: 120227
2 23 3
Company Information - Mann Tek
due to a determined expansion into growing mar-kets and recognition by customers of the robust design and reliable quality of the products.
Mann Teknik AB are certified to ISO9001:2008. The products are CE-labeled. The main pro-ducts are certified to PED, the European Pres-sure Equipment Directive and ATEX, the European directive for Equipment intended for use in Potentially Explosive Atmospheres. The products are produced in accordance with several important standards, e.g. the NATO STANAG 3756
Mann Teknik AB is a Swedish company loca-ted in Mariestad, Sweden.
Mann Teknik AB produces and markets products for safe and environmentally friendly handling of aggressive fluids for the chemical and petroche-mical industries.
The main product is the Dry Disconnect Coup-lings, DDCouplings®, for spill free liquid handling. The products are marketed through independent representatives in more than 30 countries. Mann Teknik AB have many years of experience in designing, producing and marketing of DDCoup-lings® all since 1977.
Mann Teknik AB has shown a high rate of growth during the past years and is now a major player in its specialised field of operation. This is
Phone: +46 501 39 32 00Email: [email protected] site: www.mann-tek.com
Quality, Health, Safety and Environment Policy
Titel
Quality, Health, Safety and Environment Policy
Upprättat av Per Nordsjö
2008-05-15 Tills vidare
Godkänd av Regnr Utgåva Sidan
Our objectives are simple – no accidents, no occupational illness or work related accidents, no negative environmental impact and optimizing and continuously improving customer satisfaction wherever we operate.
Mariestad, February 28 2008
Tony Mann
What does this mean?
In our daily work to develop, sell, deliver and maintain our products this means to act as soon as we recognize a risk for:
• Delivery of products with insufficient technical quality • Giving incorrect information • Not complying with laws an regulations concerning our operation• Causing negative environmental impact • Causing occupational illness or accidents• Not be able to keep promises on delivery terms (product and
information)
To act, here means to point out the risk and to make sure we take a balanced decision to prevent what is undesired.
(This policy includes all that is traditionally covered in separate policies for quality, health, safety and environment)
Per Nordsjö POL-108 2 1 av 1 UTSKRIVEN KOPIA GÄLLER EJ SOM ORIGINAL
2 23 3
DECLARATION OF CONFORMITY:EC-Directive 94/9/EC (ATEX)
Mann Teknik AB of Strandvägen 16, SE-542 31 Mariestad, Sweden, hereby declares that the products listed comply with the essential requirements of the ATEX EC-Directive 94/9/EC.
Product models listed
SBCouplings (Safety Break-Away Couplings)
The following harmonized standards are applicable
SS-EN 1127-1 Explosion prevention and protection
SS-EN 13463-1 Non electrical equipment for potentially atmospheres, basic method and requirements.
SS-EN 13463-5 Non electrical equipment for potentially atmospheres, protection by constructional safety.
Marking: II 3G
The manufacturer attested, that the SBCouplings satisfy the stated requirements and may therefore be used in category 3, group II.
Signed:
Name: Tony Mann
Title: General Manager
Date: 26th January 2011
Mann Teknik AB Strandvägen 16, S-542 31 Mariestad, Sweden Phone +46 501 393200 • Fax +46 501 393209 www.mann-tek.com • [email protected]
Mann Teknik AB is a certified ISO9001-company.
DECLARATION OF CONFORMITY:Pressure Equipment Directive 97/23/ECMann Teknik AB of Strandvägen 16, SE-542 31 Mariestad, Sweden hereby declares that the products listed comply with the essential requirements of the Pressure Equipment Directive 97/23/EC.
Pressure accessories:DDCouplings (STANAG), DGCouplings, DACouplings (ISO45) and SBCouplings
Conformity assessment procedure followed: no CE-marking** SEP=sound engineering praxis Article 3 section 3* CE 0038 Cat 1=Category 1 Module A CE 0038 Cat 2=Category 2 Module D1
For piping intended for gases, liquefied gases, gases dissolved under pressure, etc. according to article 3 paragraph 1.3.(a) [Annex II Table 6] Al Br SS DN25 PN16 SEP* PN16 SEP* PN25 SEP* DN40 PN16 Cat 1 PN16 Cat 1 PN25 Cat 1 DN50 PN16 Cat 1 PN16 Cat 1 PN25 Cat 2DN65 PN10 Cat 1 PN16 Cat 2 PN25 Cat 2DN80 PN10 Cat 1 PN16 Cat 2 PN25 Cat 2DN100 PN10 Cat 1 PN16 Cat 2 PN25 Cat 2DN150 PN16 Cat 2
For piping intended for liquids according to article 3 paragraph 1.3.(b) [Annex II Table 8] Al Br SS
DN25 PN16 SEP* PN16 SEP* PN25 SEP* DN40 PN16 SEP* PN16 SEP* PN25 SEP* DN50 PN16 SEP* PN16 SEP* PN25 SEP* DN65 PN10 SEP* PN16 SEP* PN25 SEP* DN80 PN10 SEP* PN16 SEP* PN25 SEP* DN100 PN10 SEP* PN16 SEP* PN25 Cat 1DN150 PN10 SEP* PN16 Cat 1*According to Article 3 section 3, the products designed and manufactured in accordance with the sound engineering practice (SEP) must not bear the CE marking. Unauthorized product modifications lead to an invalid declaration. **Attention:If the coupling is Ex-marked the CE-marking is for ATEX classification
Notified body Identification number 0038 Lloyds Register Verification Ltd. 71 Fenchurch Street EC3M 4BS London
United Kingdom
Signed:
Name: Tony Mann
Title: General Manager
Date: 2nd February 2012
Mann Teknik AB is a certified ISO9001-company
Declaration of Conformity
Conformity declaration regarding Pressure Equipment Directive 97/23/EC Category I and II
Conformity declaration regar-ding Directive for Equipment for the use in potentially explosive atmosphere 94/9/EC (ATEX)
DDCouplings ®
Dry Disconnect Couplings
DGCouplings ®
Dry Gas Couplings
DACouplings ®
Dry Aviation Couplings
Quality Approvals
Lloyd’s Register: Quality Management System acc. to Pres-sure Equipment direc-tive 97/23/ECModule D1 – Manu-facture of Dry Discon-nect and Break-away Couplings
Lloyd’s Register: Quality Manage-ment System acc. to ISO9001:2008 Standard Design, production and ser-vice of Self sealing couplings, Safety Break-away coup-lings, ball valves and Accessories.
TDT recognition:Equipment for transport vessels for transport of dange-rous goods acc to ADR/RID in Poland
Lloyd’s Register:EC Technical File Receipt Directive 94/9/EC for Equip-ment for the use in potentially explosive atmosphere (ATEX)
Product Approvals - Type approval Dry Disconnect Couplings
VdTÜV- Bautellprüfblatt TÜ-AGG 304-99DDCouplings acc. to ADR, RID
Apragaz Type approval DDCouplings acc. to ADR, RID, IMDG
Apragaz Type approval Safety Pressure Caps acc. to ADR, RID, IMDG
P 5 P 6
P 9 P 11 P 12
P 14 P 16 P 19P 18
P 8Gost: Russian certificate / Declaration of Con-formity.
Declares that Mann-Tek products are according to Russian Standard
DECLARATION OF CONFORMITY: EC-Directive 94/9/EC (ATEX)
Mann Teknik AB of Strandvägen 16, SE-542 31 Mariestad, Sweden, hereby declares that the products listed comply with the essential requirements of the ATEX EC-Directive 94/9/EC.
Product models listed
DDCouplings (STANAG), DGCouplings, DACouplings (ISO45)
The following harmonized standards are applicable
SS-EN 1127-1 Explosion prevention and protection
SS-EN 13463-1 Non electrical equipment for potentially atmospheres, basic method and requirements.
SS-EN 13463-5 Non electrical equipment for potentially atmospheres, protection by constructional safety.
Marking: II 2GThe manufacturer attested, that the DDCouplings®, DACouplings and DGCouplings satisfy the stated requirements and may therefore be used in category 2, group II.
Technical file receiptStorage No. 0038/ATEX/HAM0664017
Notified body
Identification number 0038 Lloyds Register Verification Limited 71 Fenchurch Street EC3M 4BS London
United Kingdom
Signed:
Name: Tony Mann
Title: General Manager
Date: 26th January 2011
Mann Teknik AB is a certified ISO9001-company P 7
P 10
P 13
Roztechnadzar Permission for appli-ances of the Russian Federation (Roz-technadzar) confirming correspon-dence of equipment in the sphere of industrial safety.
TÜV Type approval TÜ-AGG 304-99DDCouplings, acc. to ADR, RID
Quality ApprovalsD
DCo
uplin
gs®
Dry
Dis
conn
ect
Coup
lings
4 45 5
BWB, Bundesamt für Wehrtechnik und BeschaffungApproval of DDCoup-lings for use in fuel handling application
CEFIC-Working group Ethylene Oxide:Recommendation for the use of DDCoup-lings in EO-applica-tions
CEFIC-Working group Acrylic Mo-nomers:Recommendation for the use of DD-Couplings in acrylic monomers loading applications
CEFIC-Working group Acrylnitrile:Recommendation for the use of DDCoup-lings in acrylnitrile loading applications
TÜV Type approval TÜ-AGG 304-99DGCouplingsacc. to ADR, RID
VdTÜV- Bautellprüfblatt TÜ-AGG 304-99DGCouplingsacc. to ADR, RID
Apragaz Type approval DGCouplingsacc. to ADR, RID, IMDG
Apragaz Type approval Ball Valves acc. to ADR, RID, IMDG
Apragaz Type appro-val Ball Valves 2-way acc. to ADR, RID, IMDG
September 2004
EUROPEAN BASIC ACRYLIC MONOMER GROUP (EBAM)
Dry Disconnect Couplings for Acrylic Materials Service
Industry Recommendation
In their drive to improve the health and environment standards in the acrylic materials distribution chain, member companies of the European Basic Acrylic Monomers Sector Group are recommending the use of dry disconnect couplings on the transport equipment for bulk shipments of acrylic acid, methyl acrylate, ethyl acrylate, butyl acrylates and 2-ethyl hexyl acrylate.
Caution needs to be exercised when connecting the fixed and mobile parts of couplings from different manufacturers. Compatibility information is available in the EBAM document entitled “Use of dry disconnect couplings on transportation equipment for acrylic monomers service”,which can be downloaded from the following address:
http://www.petrochemistry.net/templates/shwArticle.asp?TID=5&SNID=22&AID=43
Rail tank cars, road tank vehicles and portable tanks used for these acrylic monomers need to be equipped with either 2” or 3” couplings.
The connecting nozzle could be designed according to the November 1994 NATO standard. Couplings manufacturers must also show that they have introduced an ISO 9000 quality assurance system.
The recommendation is given to the best of the EBAM member company ies’ knowledge, and is made withoutany guarantee as the conditions of use are beyond the industry's control. Neither Cefic nor any member of theCefic EBAM sector group shall have any liability whatsoever for any decision based on this recommendation.
46
Appendix 2
Design and Construction of Road Tankers and Tank Containers
3.2.3.The size of the pressure relief valve(s) should be determined inaccordance with API 520, the appropriate DIN method or an equivalentwhich is approved by the Company.
They must be designed and constructed so that in the case of total fireengulfment, the pressure inside the tank does not exceed the hydraulic testpressure of 4 bar g.
3.2.4.The pressure relief valve(s) must be set to open automatically at 0.9times the test pressure, i.e. at 3.6 bar gauge, and to be fully open at the testpressure. The bursting disc rupture pressure must be the test pressure, i.e.4.0 bar gauge.
3.2.5.It is recommended to design the tank to withstand full vacuumconditions. If this is not the case, the tank must be fitted with a vacuumrelief valve designed to suit the maximum differential pressure conditionsthat the tank will withstand.
3.3. Filling/discharge and vapour return connections3.3.1. All openings in the tank shell must be above the surface level of theliquid. No pipes or pipe connections must pass through the walls of the shellbelow the surface level of the liquid.
3.3.2.The filling/discharge and vapour return connections must be on top ofthe tank and incorporate a DN 80 filling/discharge and DN 50 vapour returnlines with preferably stainless steel ball valves or butterfly valves. The handle ofthe valve should incorporate a locking pin/device to avoid product release byaccidentally moving the valve handle. The connections must be closed withstainless steel blanking flanges (or compatible materials).For environmental and operational reasons, ‘DRY DISCONNECT COUPLINGS’for loading and unloading can be used.For current information on the recommended type of ‘DRY DISCONNECTCOUPLING’, contact the Secretariat of the CEFIC Acrylonitrile TechnicalWorking Group.
3.3.3. The filling/discharge pipe must be 80 mm diameter and reach as close aspracticable to the bottom of the tank. It must be supported top and bottom soas to withstand any vibration caused by the movement of the vehicle.
3.3.4.Emptying of the tank by pressure using an inert gas must be through thevapour return connection. This connection shall also be used for vapour returnduring tanker filling operations.
3.3.5. These connections must be provided with means to prevent unauthorisedaccess. A tamper proof cap covering all top connections must be fitted.
Applicability Dry Disconnect Couplings
Type approval Dry Aviation Couplings
TÜV Type approval TÜ-AGG 304-99DACouplings acc. to ADR, RID
VdTÜV- Bautellprüfblatt TÜ-AGG 304-99DACouplings acc. to ADR, RID
FMV, Försvarets Material-verk. Approval of DACouplings for use in Avia-tion fuel handling application
Applicability Aviation Couplings
Type approval Dry Gas Couplings Full Flow Ball Valves
DD
Coup
lings
®
Dry
Dis
conn
ect
Coup
lings
DAC
oupl
ings
®
Dry
Avi
atio
n Co
uplin
gs
FFB
all V
alve
sFu
ll Fl
ow B
all V
alve
s
DG
Coup
lings
®
Dry
Gas
Cou
plin
gs
P 14
P 21 P 23P 20 P 22
P 16 P 24
P 25 P 26 P 27
Type approval Safety Break-away Couplings
P 15 P 17
P 14 P 16
TÜV Type approval TÜ-AGG 437-11SBCouplings, In- dustrial and Marine type
VdTÜV- Bautellprüfblatt TÜ-AGG 437-11SBCouplings, Indu-strial and Marine type
SBCo
uplin
gs®
Safe
ty B
reak
-aw
ay C
oupl
ings
4 45 5
Declaration of Conformity
Conformity declaration regarding Pressure Equipment Directive 97/23/EC Category I and II
DECLARATION OF CONFORMITY:Pressure Equipment Directive 97/23/ECMann Teknik AB of Strandvägen 16, SE-542 31 Mariestad, Sweden hereby declares that the products listed comply with the essential requirements of the Pressure Equipment Directive 97/23/EC.
Pressure accessories:DDCouplings (STANAG), DGCouplings, DACouplings (ISO45) and SBCouplings
Conformity assessment procedure followed: no CE-marking** SEP=sound engineering praxis Article 3 section 3* CE 0038 Cat 1=Category 1 Module A CE 0038 Cat 2=Category 2 Module D1
For piping intended for gases, liquefied gases, gases dissolved under pressure, etc. according to article 3 paragraph 1.3.(a) [Annex II Table 6] Al Br SS DN25 PN16 SEP* PN16 SEP* PN25 SEP* DN40 PN16 Cat 1 PN16 Cat 1 PN25 Cat 1 DN50 PN16 Cat 1 PN16 Cat 1 PN25 Cat 2DN65 PN10 Cat 1 PN16 Cat 2 PN25 Cat 2DN80 PN10 Cat 1 PN16 Cat 2 PN25 Cat 2DN100 PN10 Cat 1 PN16 Cat 2 PN25 Cat 2DN150 PN16 Cat 2
For piping intended for liquids according to article 3 paragraph 1.3.(b) [Annex II Table 8] Al Br SS
DN25 PN16 SEP* PN16 SEP* PN25 SEP* DN40 PN16 SEP* PN16 SEP* PN25 SEP* DN50 PN16 SEP* PN16 SEP* PN25 SEP* DN65 PN10 SEP* PN16 SEP* PN25 SEP* DN80 PN10 SEP* PN16 SEP* PN25 SEP* DN100 PN10 SEP* PN16 SEP* PN25 Cat 1DN150 PN10 SEP* PN16 Cat 1*According to Article 3 section 3, the products designed and manufactured in accordance with the sound engineering practice (SEP) must not bear the CE marking. Unauthorized product modifications lead to an invalid declaration. **Attention:If the coupling is Ex-marked the CE-marking is for ATEX classification
Notified body Identification number 0038 Lloyds Register Verification Ltd. 71 Fenchurch Street EC3M 4BS London
United Kingdom
Signed:
Name: Tony Mann
Title: General Manager
Date: 2nd February 2012
Mann Teknik AB is a certified ISO9001-company
6 67 7
Conformity declaration regarding Directive for Equipment for the use in potentially explosive atmosphere 94/9/EC (ATEX).
Declaration of Conformity
DECLARATION OF CONFORMITY: EC-Directive 94/9/EC (ATEX)
Mann Teknik AB of Strandvägen 16, SE-542 31 Mariestad, Sweden, hereby declares that the products listed comply with the essential requirements of the ATEX EC-Directive 94/9/EC.
Product models listed
DDCouplings (STANAG), DGCouplings, DACouplings (ISO45)
The following harmonized standards are applicable
SS-EN 1127-1 Explosion prevention and protection
SS-EN 13463-1 Non electrical equipment for potentially atmospheres, basic method and requirements.
SS-EN 13463-5 Non electrical equipment for potentially atmospheres, protection by constructional safety.
Marking: II 2GThe manufacturer attested, that the DDCouplings®, DACouplings and DGCouplings satisfy the stated requirements and may therefore be used in category 2, group II.
Technical file receiptStorage No. 0038/ATEX/HAM0664017
Notified body
Identification number 0038 Lloyds Register Verification Limited 71 Fenchurch Street EC3M 4BS London
United Kingdom
Signed:
Name: Tony Mann
Title: General Manager
Date: 26th January 2011
Mann Teknik AB is a certified ISO9001-company
6 67 7
Declaration of Conformity
DECLARATION OF CONFORMITY:EC-Directive 94/9/EC (ATEX)
Mann Teknik AB of Strandvägen 16, SE-542 31 Mariestad, Sweden, hereby declares that the products listed comply with the essential requirements of the ATEX EC-Directive 94/9/EC.
Product models listed
SBCouplings (Safety Break-Away Couplings)
The following harmonized standards are applicable
SS-EN 1127-1 Explosion prevention and protection
SS-EN 13463-1 Non electrical equipment for potentially atmospheres, basic method and requirements.
SS-EN 13463-5 Non electrical equipment for potentially atmospheres, protection by constructional safety.
Marking: II 3G
The manufacturer attested, that the SBCouplings satisfy the stated requirements and may therefore be used in category 3, group II.
Signed:
Name: Tony Mann
Title: General Manager
Date: 26th January 2011
Mann Teknik AB Strandvägen 16, S-542 31 Mariestad, Sweden Phone +46 501 393200 • Fax +46 501 393209 www.mann-tek.com • [email protected]
Mann Teknik AB is a certified ISO9001-company.
Conformity declaration regarding Directive for Equipment for the use in potentially explosive atmosphere 94/9/EC (ATEX).
8 89 9
Quality Approvals
Gost Certificate is a Russian Declaration of Conformity. Declares that Mann-Tek products are according to Russian Standard
8 89 9
Quality Approvals
Lloyd’s Register: Quality Management System acc. to Pressure Equipment Directive 97/23/ECModule D1 – Manufacture of Dry disconnect and Break-away couplings.
10 1011 11
Lloyd’s Register: Quality Management System acc. to ISO9001:2008 Standard Design, production and service of Self sealing couplings, Safety Break-away couplings, ball valves and Accessories.
Quality Approvals
10 1011 11
Quality Approvals
TDT recognition:Equipment for transport vessels for transport of dangerous goods acc to ADR/RID in Poland
12 1213 13
Quality Approvals
Lloyd’s Register:EC Technical File Receipt Directive 94/9/EC for Equipment for the use in potentially explosive atmosphere (ATEX)
12 1213 13
Quality Approvals
Permission for appliances of the Russian Federation (Roztechnadzar) confirming correspondence of equipment in the sphere of industrial safety.
Roztechnadzar
14 1415 15
Product Approvals
TÜV Type approval TÜ-AGG 304-99DDCouplings, DACouplings and DGCouplings acc. to ADR, RID
DD
Coup
lings
®
Dry
Dis
conn
ect
Coup
lings
D
ACou
plin
gs®
Dry
Avi
atio
n Co
uplin
gs
DG
Coup
lings
®
Dry
Gas
Cou
plin
gs
14 1415 15
Product Approvals
SBCo
uplin
gs®
Safe
ty B
reak
-aw
ay C
oupl
ings
TÜV Type approval TÜ-AGG 437-11SBCouplings, Industrial and Marine type
16 1617 17
Product Approvals
VdTÜV-Bautellprüfblatt TÜ-AGG 304-99DDCouplings, DACouplings and DGCouplings acc. to ADR, RID
DD
Coup
lings
®
Dry
Dis
conn
ect
Coup
lings
D
ACou
plin
gs®
Dry
Avi
atio
n Co
uplin
gs
DG
Coup
lings
®
Dry
Gas
Cou
plin
gs
16 1617 17
Product Approvals
SBCo
uplin
gs®
Safe
ty B
reak
-aw
ay C
oupl
ings
VdTÜV-Bautellprüfblatt TÜ-AGG 437-11SBCouplings, Industrial and Marine type
18 1819 19
Product Approvals
Apragaz Type approval DDCouplings acc. to ADR, RID, IMDG
DD
Coup
lings
®
Dry
Dis
conn
ect
Coup
lings
18 1819 19
Product Approvals
Apragaz Type approval Safety Pressure Caps acc. to ADR, RID, IMDG
DD
Coup
lings
®
Dry
Dis
conn
ect
Coup
lings
20 2021 21
Product Approvals
BWB, Bundesamt für Wehrtechnik und BeschaffungApproval of DDCouplings for use in fuel handling application
DD
Coup
lings
®
Dry
Dis
conn
ect
Coup
lings
20 2021 21
Product Approvals
CEFIC-Working group Ethylene Oxide:Recommendation for the use of DDCouplings in EO-applications
DD
Coup
lings
®
Dry
Dis
conn
ect
Coup
lings
22 2223 23
September 2004
EUROPEAN BASIC ACRYLIC MONOMER GROUP (EBAM)
Dry Disconnect Couplings for Acrylic Materials Service
Industry Recommendation
In their drive to improve the health and environment standards in the acrylic materials distribution chain, member companies of the European Basic Acrylic Monomers Sector Group are recommending the use of dry disconnect couplings on the transport equipment for bulk shipments of acrylic acid, methyl acrylate, ethyl acrylate, butyl acrylates and 2-ethyl hexyl acrylate.
Caution needs to be exercised when connecting the fixed and mobile parts of couplings from different manufacturers. Compatibility information is available in the EBAM document entitled “Use of dry disconnect couplings on transportation equipment for acrylic monomers service”,which can be downloaded from the following address:
http://www.petrochemistry.net/templates/shwArticle.asp?TID=5&SNID=22&AID=43
Rail tank cars, road tank vehicles and portable tanks used for these acrylic monomers need to be equipped with either 2” or 3” couplings.
The connecting nozzle could be designed according to the November 1994 NATO standard. Couplings manufacturers must also show that they have introduced an ISO 9000 quality assurance system.
The recommendation is given to the best of the EBAM member company ies’ knowledge, and is made withoutany guarantee as the conditions of use are beyond the industry's control. Neither Cefic nor any member of theCefic EBAM sector group shall have any liability whatsoever for any decision based on this recommendation.
Product Approvals
CEFIC-Working group Acrylic Monomers:Recommendation for the use of DDCouplings in acrylic monomers loading applications
DD
Coup
lings
®
Dry
Dis
conn
ect
Coup
lings
22 2223 23
46
Appendix 2
Design and Construction of Road Tankers and Tank Containers
3.2.3.The size of the pressure relief valve(s) should be determined inaccordance with API 520, the appropriate DIN method or an equivalentwhich is approved by the Company.
They must be designed and constructed so that in the case of total fireengulfment, the pressure inside the tank does not exceed the hydraulic testpressure of 4 bar g.
3.2.4.The pressure relief valve(s) must be set to open automatically at 0.9times the test pressure, i.e. at 3.6 bar gauge, and to be fully open at the testpressure. The bursting disc rupture pressure must be the test pressure, i.e.4.0 bar gauge.
3.2.5.It is recommended to design the tank to withstand full vacuumconditions. If this is not the case, the tank must be fitted with a vacuumrelief valve designed to suit the maximum differential pressure conditionsthat the tank will withstand.
3.3. Filling/discharge and vapour return connections3.3.1. All openings in the tank shell must be above the surface level of theliquid. No pipes or pipe connections must pass through the walls of the shellbelow the surface level of the liquid.
3.3.2.The filling/discharge and vapour return connections must be on top ofthe tank and incorporate a DN 80 filling/discharge and DN 50 vapour returnlines with preferably stainless steel ball valves or butterfly valves. The handle ofthe valve should incorporate a locking pin/device to avoid product release byaccidentally moving the valve handle. The connections must be closed withstainless steel blanking flanges (or compatible materials).For environmental and operational reasons, ‘DRY DISCONNECT COUPLINGS’for loading and unloading can be used.For current information on the recommended type of ‘DRY DISCONNECTCOUPLING’, contact the Secretariat of the CEFIC Acrylonitrile TechnicalWorking Group.
3.3.3. The filling/discharge pipe must be 80 mm diameter and reach as close aspracticable to the bottom of the tank. It must be supported top and bottom soas to withstand any vibration caused by the movement of the vehicle.
3.3.4.Emptying of the tank by pressure using an inert gas must be through thevapour return connection. This connection shall also be used for vapour returnduring tanker filling operations.
3.3.5. These connections must be provided with means to prevent unauthorisedaccess. A tamper proof cap covering all top connections must be fitted.
Product Approvals
CEFIC-Working group Acrylnitrile:Recommendation for the use of DDCouplings in acrylnitrile loading applications
DD
Coup
lings
®
Dry
Dis
conn
ect
Coup
lings
24 2425 25
Product ApprovalsFMV, Försvarets MaterialverkApproval of DACouplings for use in Aviation fuel handling application
DAC
oupl
ings
®
Dry
Avi
atio
n Co
uplin
gs
24 2425 25
Product Approvals
Apragaz Type approval DGCouplings acc. to ADR, RID, IMDG
DG
Coup
lings
®
Dry
Gas
Cou
plin
gs
26 2627 27
Product Approvals
Apragaz Type approval Ball Valves acc. to ADR, RID, IMDG
FFB
all V
alve
sFu
ll Fl
ow B
all V
alve
s
26 2627 27
Product Approvals
Apragaz Type approval Ball Valves 2-way acc. to ADR, RID, IMDG
FFB
all V
alve
sFu
ll Fl
ow B
all V
alve
s
Contact Mann Tek for your local distributorPhone: +46 501 39 32 00 Fax: +46 501 39 32 09 Email: [email protected] Web site: www.mann-tek.com
Address: Mann Teknik AB Strandvägen 16 SE-542 31 Mariestad Swedenabcdef
Your distributor:
www.mann-tek.com Mann-Tek is a certified ISO9001-company.
Your distributor
Product Information
DDCouplings®
Dry Disconnect Coupling.¾" to 6", PN 16 - PN 25. Aluminium, Brass-Gunmetal, Stainless Steel and PEEK. Other materials on request. According to NATO standard STANAG 3756.
Full Flow - ballvalves2" to 4", PN 10, Aluminium.Ballvalve and 2-way Ballvalve.Made for Petroleum Tank Trucks. Varia-tions of flange connections.
DGCouplings®
Dry Gas Coupling.1" to 4", PN25. Stainless steel.Other materials on request.
Art. nr: PR-010101-0112 Version: 080227
Product Information
DDCouplings ®
Dry Disconnect Couplings
Art. nr: PR-010201-0111 Version: 080227
FFBall ValvesFull Flow Ball Valves
Produkt Information
Art. nr: PR-010801-0112 Version: 080214
DGCouplings ®
Dry Gas Couplings
Product Information
DACouplings, Dry Aviation Coupling. 2½", PN 10. Main body in Aluminium.Standards: ISO 45, MS 24484, NATO STANAG 3105, British Aerospace Spec. 2C14.�
Spe
cific
atio
ns s
ubje
ct to
cha
nge
with
out n
otic
e - C
opyr
ight
© M
ann
Tekn
ik A
B -
ww
w.m
ann-
tek.
se
Art. nr: PR-010601-0112 Version: 080225
Product Information
DACouplings ®
Dry Aviation Couplings
Sampling, Vent or Drain unit Stainless Steel SS-EN 10 088-1.4404+AT (AISI 316L). Ball Valve in 1.0619 and 1.4301
Art. nr: PR-021001-0121 Version: 070329
Sampling, Vent or Drain unit
AviationFuelling Equipment
Business Segment Information
Swivel joints¾" to 10", PN 10 - PN 25.Aluminium, Brass-Gunmetal, Stainless Steel.Other materials on request.Connection: BSP, NPT. Flanged connection (DIN, ANSI/ASA e.t.c)
Art. No: PR-010501-0112 Version: 090820
Product Information
SwivelsSwivel Joints
SBCouplings, bolt seriesIndustrial and Marine Safety Break-away, breaking bolts, Aluminium, Brass, Stainless Steel, 1" to 12", female/male threads and with flanges, with breaking bolts.Safety Break-away, cable release Stainless Steel, PN10 / PN 25. 2" to 4", female threads. 6" to 12", flanged connectionArt. No: PR-010301- 0112 Version: 090828
Product Information
SBCouplingsSafety Break-away Couplings
Gas (LPG)
SwivelsSwivel Joints SBCouplings ®
Safety Break-away Couplings
DGCouplings ®
Dry Gas Couplings
Sweden
Version 091012
Offshore & MarineDDCouplings ®
Dry Disconnect Couplings SwivelsSwivel Joints
SBCouplings ®
Safety Break-away Couplings
Sweden
Rail Tankers
Sweden
SwivelsSwivel Joints SBCouplings ®
Safety Break-away Couplings
DDCouplings ®
Dry Disconnect Couplings
Gas (LPG) Rail tankers
ServiceApproval InformationCompany Information
Quality, Health, Safety and Environment Policy. Quality Approvals, Product Approvals and Declaration of Conformity
ww
w.m
ann-
tek.
se
General Information
Art. nr.: PR-091901-01 Version: 090505
General Information about Mann Tek, products and Business Segments
Chemical industry
Offshore & Marine
Tank trucks
Military
Sweden
SwivelsSwivel Joints
SBCouplings ®
Safety Break-away Couplings
DDCouplings ®
Dry Disconnect Couplings
Version 100113
Military
Container
Sweden
SwivelsSwivel Joints
SBCouplings ®
Safety Break-away Couplings
DDCouplings ®
Dry Disconnect Couplings
Version 100113
Container
Service instructions and operation manuals
Tank Trucks
Sweden
SwivelsSwivel Joints
SBCouplings ®
Safety Break-away Couplings
DDCouplings ®
Dry Disconnect Couplings
Version 100113
