Qualified Products List - NH.gov manufacturer’s Safety Data Sheet (SDS) should be referred to...
Transcript of Qualified Products List - NH.gov manufacturer’s Safety Data Sheet (SDS) should be referred to...
New Hampshire Department of Transportation
Products appearing on this list have been pre-qualified by the Department for
general use. Unless noted otherwise, these products may be used on Highway and Bridge projects under the Section/Item Number indicated, without further testing.
Products that are listed with an “Expiration Date” are only qualified for use through that date.
A Certificate of Compliance is required for these materials. A product that falls into one of these categories and is not listed shall not be used,
unless qualified through written request to the NHDOT, Bureau of Materials & Research. Such request shall be made with sufficient lead-time to allow for any necessary testing and/or research.
Products shall conform to NH Code of Administrative Rules Chapter Env-A 4200
Architectural and Industrial Maintenance Coatings, available from the NH Department of Environmental Services, and all other State and Federal regulations related to safety or environmental issues in effect at the time of use. Inclusion of a product on this list does not imply that the product meets such regulations.
The manufacturer’s Safety Data Sheet (SDS) should be referred to before use of any
product appearing on this list. Unless denoted otherwise in the plans or specifications, manufacturer
recommendations related to preparation, application, coverage, and shelf life shall be followed for all products appearing on this list.
Report any failure, incompatibility or other problem associated with any product on
this list to:
Product Evaluation Supervisor, NHDOT Bureau of Materials & Research PO Box 483, Concord, NH 03302-0483
Tel: (603) 271-3151 Fax: (603) 271-8700
Qualified Products List Issue 2016-1
January 15, 2016
NOTICE
Qualified Products List
Table of Contents
Section Number Category Description403 A. Not currently used.
B. Not currently used.
C. ITEM 403.6 - PAVEMENT JOINT ADHESIVE
413 A. ITEM 413.1 - HOT POURED CRACK SEALANT (AASHTO M 324, Type II)
B. ITEM 413.2 - HOT POURED CRACK SEALANT (LOW MODULUS, AASHTO M 324, Type IV modified)
510 A. ITEM 510.65 - DRIVING POINTS FOR STEEL BEARING PILES
511 A. Not Currently used
520 A. FAST SET NON-SHRINK PATCHING MORTAR (For horizontal repairs)
B. Not Currently Used
C. AIR ENTRAINING ADMIXTURES
D. WATER REDUCING ADMIXTURES
E. RETARDING ADMIXTURES
F. WATER-REDUCING, HIGH-RANGE ADMIXTURES
G. CORROSION INHIBITORS
H. CURING COMPOUNDS
I. Not currently used.
J. Not currently used.
K. BEARING STRIP (RUBBER-BACKED UHMV-PE)
L. Not currently used
M. EXTRUDED POLYSTYRENE (XPS) RIGID FOAM
526 A. ITEM 526.2 - EPOXY FOR NON-MOVING CRACKS
528 A. HIGH-STRENGTH, IMPACT-RESISTANT NON-SHRINK GROUT
530 A. ITEM 530.3 - CEMENT BASE WITH ACRYLIC LATEX (2 Coats)
B. ITEM 530.3 - CEMENT BASE, POLYMER MODIFIED (2 Coats)
532 A. ITEM 532.1 - SEMI-PERMANENT ANTI-GRAFFITI COATINGS (CLEAR)
534 A. Not currently used
B. ITEM 534.3 - SILANE/SILOXANE
C. ITEM 534.3 - SILANE/SILOXANE - COLD WEATHER
538 A. ITEM 538.1 - BARRIER MEMBRANE, PEEL AND STICK
B. ITEM 538.2 - BARRIER MEMBRANE, PEEL AND STICK - VERTICAL SURFACES
C. PROTECTION BOARD FOR BARRIER MEMBRANE
D. Not currently used
E. HOT RUBBERIZED ASPHALT
F. ITEM 538.5 - BARRIER MEMBRANE, HEAT WELDED
G. ITEM 538.6 - BARRIER MEMBRANE, HEAT WELDED - MACHINE METHOD
H. Not currently used
I. MOISTURE METER (For concrete bridge decks)
Issue 2016-01Page 1 of 30
Qualified Products List
541 A. ITEM 541.1 - WATERSTOP, NH TYPE 1
B. ITEM 541.2 - WATERSTOP, NH TYPE 2
C. ITEM 541.3 - WATERSTOP, NH TYPE 3
D. ITEM 541.4 - WATERSTOP, NH TYPE 4
E. ITEM 541.5 - WATERSTOP, NH TYPE 5
544 A. SYNTHETIC FIBER REINFORCEMENT
550 A. FAST SETTING GROUTS FOR ANCHOR BOLTS (550.3.15.4.2)
B. STICK WAX FOR HIGH STRENGTH A325 & A490 FASTENERS
559 A. ITEM 559.4 - ASPHALTIC PLUG EXPANSION JOINT (formerly "Elastomeric Plug Type Expansion Joint")
B. Not currently used
C. ITEM 559.41 - ASPHALTIC PLUG FOR CRACK CONTROL (formerly "Modified Elastomeric Plug Type Expansion Joint - 6" wide)
D. ITEM 559.412 - REPAIR ASPHALTIC PLUG EXPANSION JOINT (Formerly Modified Elastomeric Plug Type Expansion Joint - 20" Wide)
E. CLOSED CELL EXPANSION MATERIAL
560 A. PREFABRICATED COMPRESSION SEAL EXPANSION JOINT
561 A. PREFAB. STRIP SEAL EXPANSION JOINT
B. PREFAB. MODULAR BRIDGE JOINT SYSTEM
C. PREFORMED FABRIC TROUGH (Used with prefabricated finger joints)
562 A. SILICONE JOINT SEALANT (Non-sag, for vertical and horizontal joints).
B. SILICONE JOINT SEALANT (Self-leveling, for horizontal joints)
593 A. ITEM 593.ABC - GEOTEXTILES
604 A. FIBER REINFORCEMENT FOR PRECAST DRAINAGE STRUCTURES
606 A. SYNTHETIC OFFSET BLOCKS
B. ITEM 606.9512 - TEMPORARY IMPACT ATTENUATION DEVICE (Redirective), Test Level 2
C. ITEM 606.9513 - TEMPORARY IMPACT ATTENUATION DEVICE (Redirective), Test Level 3
D. ITEM 606.9522 - TEMPORARY IMPACT ATTENUATION DEVICE (Non-redirective), Test Level 2
E. ITEM 606.9523 - TEMPORARY IMPACT ATTENUATION DEVICE (Non-redirective), Test Level 3
609 A. NON-SHRINK, NON-METALLIC GROUT (Cement Mortar for Bedding Curb; Bridge)
B. POLYESTER FIBERS FOR BITUMINOUS CURB
616 A. SAW CUT LOOP SEALANT
619 A. TEMPORARY RAISED PAVEMENT MARKERS
632 A. ITEM 632.1 - PREFORMED RETROREFLECTIVE TAPE, TYPE I (REMOVABLE)
B. Not Currently Used
C. ITEM 632.5 - PREFORMED RETROREFLECTIVE TAPE, LEVEL I
D. ITEM 632.6 - PREFORMED RETROREFLECTIVE TAPE, LEVEL II
E. Not currently used
F. ITEM 632.9 - PREFORMED BLACKOUT TAPE, TYPE I (REMOVABLE)
645 A. through G. These categories are not currently used.
H. TACKIFIERS
I. Not currently used.
Issue 2016-01Page 2 of 30
Qualified Products List
J. ITEM 645.41 - TEMPORARY SLOPE STABILIZATION TYPE A
K. ITEM 645.42 - TEMPORARY SLOPE STABILIZATION TYPE B (Wildlife friendly)
L. ITEM 645.43 - TEMPORARY SLOPE STABILIZATION TYPE C
M. ITEM 645.44 - TEMPORARY SLOPE STABILIZATION TYPE D (Wildlife friendly)
N. ITEM 645.45 - PERMANENT CHANNEL STABILIZATION TYPE A
O. ITEM 645.46 - PERMANENT CHANNEL STABILIZATION TYPE B
718 A. Not currently used
B. Not currently used
C. RETROREFLECTIVE SHEETING - TYPE IV
D. RETROREFLECTIVE SHEETING - TYPE VIII
E. RETROREFLECTIVE SHEETING - TYPE IX
F. Not currently used
G. OVERLAY FILM
H. RETROREFLECTIVE SHEETING - TYPE XI
Issue 2016-01Page 3 of 30
Qualified Products List
SECTION 403 - HOT BITUMINOUS PAVEMENT
A. Not currently used.
B. Not currently used.
C. ITEM 403.6 - PAVEMENT JOINT ADHESIVE
Manufacturer: Product:
These products are qualified as being able to meet the requirments of Sections 401 & 403 of the NHDOT Standard Specifications for Road and Bridge Construction.
Crafco Pavement Joint AdhesiveCrafco, Inc.
Dura-Fill CJAP&T Products, Inc.
SECTION 413 - HOT-POURED CRACK SEALANT
A. ITEM 413.1 - HOT POURED CRACK SEALANT (AASHTO M 324, Type II)
Manufacturer: Product: Expiration Date:Flex a Fill 9005Crafco, Inc. 1/1/2017
Road Saver 201Crafco, Inc. 1/1/2017
Crack-Rite HP3405Dalton Enterprises, Inc. 1/1/2017
Hi-SpecW.R. Meadows 1/1/2017
B. ITEM 413.2 - HOT POURED CRACK SEALANT (LOW MODULUS, AASHTO M 324, Type IV modified)
Manufacturer: Product: Expiration Date:Road Saver 231Crafco, Inc. 1/1/2017
Deery 101Deery Brand (Crafco Inc.) 1/1/2017
MACSEAL 6690-4 (formerly, BERAM 195 LM)McAsphalt Industries 1/1/2017
Issue 2016-01Page 4 of 30
Qualified Products List
SECTION 510 - BEARING PILES
A. ITEM 510.65 - DRIVING POINTS FOR STEEL BEARING PILES
Manufacturer: Product:Hard-Bite HP 77600-BAssoc. Pile & Fitting Corp.
Hard-Bite HP 77750-BAssoc. Pile & Fitting Corp.
Hard-Bite HP 7780-B *Assoc. Pile & Fitting Corp.
Pruyn Point HP 75750-BAssoc. Pile & Fitting Corp.
Tuftip Tufloy H-777 *Dougherty Foundation Prod., Inc.
Model HPH **Mid-America Foundation Supply
Super-Bite PAR-T SeriesPiling Accessories, Inc.
Versa-Bite VB 300-P SeriesVersabite Piling Accessories
* Available only in Grade 90-60
** Available only in Grade 65-35
SECTION 511 - PREPARATION FOR CONCRETE BRIDGE DECK REPAIRS
A. Not Currently used
Issue 2016-01Page 5 of 30
Qualified Products List
SECTION 520 - PORTLAND CEMENT CONCRETE
A. FAST SET NON-SHRINK PATCHING MORTAR (For horizontal repairs)
Manufacturer: Product:
Note: Products must be tested by the AASHTO National Transportation Product Evaluation Program (NTPEP) which requires retesting every 5 years. Products are considered to be qualified only through the indicated expiration date.
Expiration Date:MasterEmaco T 1060 (formerly 10-60 Rapid Mortar) *BASF 1/1/2019
Rapid Set DOT Concrete Mix *CTS Cement Manufacturing Corp. 1/1/2020
Rapid Set DOT Repair Mix *CTS Cement Manufacturing Corp. 1/1/2020
HD 50 *Dayton Superior Corp. 1/1/2020
Euco Repair V100 * ~Euclid Chemical Company 1/1/2020
Commercial Grade FastSet DOT Mix * ~Quikrete 1/1/2019
Rapid Road Repair *Quikrete 1/1/2019
SikaQuick VOH * ~Sika Corporation 1/1/2020
SilproRapid *Silpro LLC 1/1/2020
SilproRepair VOH * ~Silpro LLC 1/1/2020
RepCon 928SpecChem 1/1/2020
RepCon V/O * ~SpecChem 1/1/2020
Duracal *USG 1/1/2020
* High Early Strength (1000 psi minimum at 1 hour - lab)
~ Recommended also for vertical/overhead patching
B. Not Currently Used
C. AIR ENTRAINING ADMIXTURES
Manufacturer: Product:
Use of a qualified admixture is contingent upon approval of a concrete mix design that includes the admixture as a component. Note: Products must be tested by the AASHTO National Transportation Product Evaluation Program (NTPEP) which requires retesting every 5 years. Products are considered to be qualified only through the indicated expiration date.
Expiration Date:MasterAir AE 200 (formerly Micro-Air)BASF 1/1/2018
MasterAir AE 90 (formerly MB AE 90)BASF 1/1/2018
Sika AEA-14Sika Corporation 1/1/2017
Sika AirSika Corporation 1/1/2020
Sika Air-260Sika Corporation 1/1/2018
Daravair 1000 (Daravair Pave 10)W.R. Grace 1/1/2017
Darex IIW.R. Grace 1/1/2020
Issue 2016-01Page 6 of 30
Qualified Products List
D. WATER REDUCING ADMIXTURES
Manufacturer: Product:
Use of a qualified admixture is contingent upon approval of a concrete mix design that includes the admixture as a component. Note: Products must be tested by the AASHTO National Transportation Product Evaluation Program (NTPEP) which requires retesting every 5 years. Products are considered to be qualified only through the indicated expiration date.
Expiration Date:MasterGlenium 3030BASF 1/1/2019
MasterGlenium 7500 (formerly Glenium 7500)BASF 1/1/2017
MasterGlenium 7620BASF 1/1/2020
MasterPolyheed 1020 (formerly PolyHeed 1020)BASF 1/1/2018
MasterPolyHeed 1725 (formerly PolyHeed )BASF 1/1/2018
MasterPolyheed 997 ( formerly Polyheed 997)BASF 1/1/2018
MasterPozzolith 200 (formerly Pozzolith 200N)BASF 1/1/2017
MasterPozzolith 322BASF 1/1/2017
MasterSet DELVO (formerly Delvo Stabilizer)BASF 1/1/2017
Plastocrete 161Sika Corporation 1/1/2018
Sika ViscoCrete 2100Sika Corporation 1/1/2020
Sikament AFMSika Corporation 1/1/2018
SikaPlast 300GPSika Corporation 1/1/2019
SikaPlast 500Sika Corporation 1/1/2019
ViscoCrete 1000Sika Corporation 1/1/2018
Viscocrete 6100Sika Corporation 1/1/2019
ADVA 140 (M)W.R. Grace 1/1/2020
ADVA 190W.R. Grace 1/1/2020
ADVA CAST 585W.R. Grace 1/1/2020
ADVA CAST 600W.R. Grace 1/1/2019
Daracem 55W.R. Grace 1/1/2020
Daracem 65W.R. Grace 1/1/2017
MIRA 95W.R. Grace 1/1/2020
WRDA/HYCOLW.R. Grace 1/1/2017
ADVA 198W.R.Grace 1/1/2020
EXP 950W.R.Grace 1/1/2020
Issue 2016-01Page 7 of 30
Qualified Products List
E. RETARDING ADMIXTURES
Manufacturer: Product:
Use of a qualified admixture is contingent upon approval of a concrete mix design that includes the admixture as a component. Note: Products must be tested by the AASHTO National Transportation Product Evaluation Program (NTPEP) which requires retesting every 5 years. Products are considered to be qualified only through the indicated expiration date.
Expiration Date:MasterPozzolith 200 (formerly Pozzolith 200N)BASF 1/1/2017
MasterPozzolith 322BASF 1/1/2017
MasterSet DELVO (formerly Delvo Stabilizer)BASF 1/1/2017
MasterSet R 100 (formerly Pozzolith 100XR)BASF 1/1/2019
MasterSet R 961 (formerly Pozzolith 961R)BASF 1/1/2017
PlastimentSika Corporation 1/1/2020
Plastocrete 161Sika Corporation 1/1/2018
Sikatard 440Sika Corporation 1/1/2019
Daratard 17W.R.Grace 1/1/2020
RecoverW.R.Grace 1/1/2020
Issue 2016-01Page 8 of 30
Qualified Products List
F. WATER-REDUCING, HIGH-RANGE ADMIXTURES
Manufacturer: Product:
Use of a qualified admixture is contingent upon approval of a concrete mix design that includes the admixture as a component. Note: Products must be tested by the AASHTO National Transportation Product Evaluation Program (NTPEP) which requires retesting every 5 years. Products are considered to be qualified only through the indicated expiration date.
Expiration Date:MasterGlenium 3030BASF 1/1/2019
MasterGlenium 3400 (formerly Glenium 3400)BASF 1/1/2019
MasterGlenium 7500 (formerly Glenium 7500)BASF 1/1/2017
MasterGlenium 7620BASF 1/1/2020
MasterGlenium 7700BASF 1/1/2019
MasterGlenium 7710BASF 1/1/2020
MasterPolyheed 1020 (formerly PolyHeed 1020)BASF 1/1/2018
MasterPolyHeed 1725BASF 1/1/2018
MasterPolyheed 997 ( formerly Polyheed 997)BASF 1/1/2018
MasterRheobuild 1000 (formerly Rheobuild 1000)BASF 1/1/2017
Sika ViscoCrete 2100Sika Corporation 1/1/2020
Sika ViscoCrete 6100Sika Corporation 1/1/2019
Sikament 610Sika Corporation 1/1/2017
Sikament AFMSika Corporation 1/1/2018
Sikaplast 500Sika Corporation 1/1/2019
ViscoCrete 1000Sika Corporation 1/1/2018
ADVA 140 (M)W.R. Grace 1/1/2020
ADVA 190W.R. Grace 1/1/2020
ADVA Cast 535 (formerly, EXP 684)W.R. Grace 1/1/2018
ADVA CAST 575W.R. Grace 1/1/2018
ADVA CAST 585W.R. Grace 1/1/2020
MIRA 95W.R. Grace 1/1/2020
Adva 198W.R.Grace 1/1/2020
ADVA Cast 600W.R.Grace 1/1/2019
EXP 950W.R.Grace 1/1/2020
G. CORROSION INHIBITORS
Manufacturer: Product:
Use of a qualified admixture is contingent upon approval of a concrete mix design that includes the admixture as a component. Note: Products must be tested by the AASHTO National Transportation Product Evaluation Program (NTPEP) which requires retesting every 5 years. Products are considered to be qualified only through the indicated expiration date.
Expiration Date:MasterLife CI 30 (formerly Rheocrete CNI)BASF 1/1/2017
CNISika Corporation 1/1/2021
DCIW.R. Grace 1/1/2019
DCI-SW.R. Grace 1/1/2018
Issue 2016-01Page 9 of 30
Qualified Products List
H. CURING COMPOUNDS
Manufacturer: Product:
See specifications for limitations regarding the use of curing compounds.
White Resin Cure J10W (formerly D.S.S.C.C. White Resin Cure)
Dayton Superior
Thinfilm 420 w/DyeKaufman Products, Inc.
Thinfilm 450Kaufman Products, Inc.
Cure R (w/fugitive dye)L&M Construction Chemicals Inc.
Harris Super Konkure White Emulsion (formerly, Harris Super Konkure White)
Poly Sat Inc.
I. Not currently used.
J. Not currently used.
K. BEARING STRIP (RUBBER-BACKED UHMV-PE)
Manufacturer: Product:
For use with "deck over backwall" expansion. Adhesive shall be as recommended by the manufacturer of the non-slip bearing strip.
Korolath UHMW Rubber BackedKorolath of New England, Inc.
Tivar 1000 Rubber BackedQuadrant Plastics
Polystone M Rubber BackedRöchling Engineering Plastics
L. Not currently used
M. EXTRUDED POLYSTYRENE (XPS) RIGID FOAM
Manufacturer: Product:
For use as a filler material in forming concrete joints and between concrete sections.
STYROFOAMDow Building Solutions
Extruded Polystyrene Insulation BoardGreenGuard
Foamular 250Owens Corning
Issue 2016-01Page 10 of 30
Qualified Products List
SECTION 526 - CONCRETE CRACK SEALERS
A. ITEM 526.2 - EPOXY FOR NON-MOVING CRACKS
Manufacturer: Product:Concresive 1380BASF
Sure-Inject J-56Dayton Superior
Hilti CI 060 EP Crack Injection SystemHilti, Inc.
Sikadur 35 (Warm Weather)Sika Corporation
Sikadur 52 (Cool Weather)Sika Corporation
SECTION 528 - PRESTRESSED CONCRETE MEMBERS
A. HIGH-STRENGTH, IMPACT-RESISTANT NON-SHRINK GROUT
Manufacturer: Product:
This is a 3-year sole source product approval issued by the FHWA.
Expiration Date:Sure-Grip High Performance GroutDayton Superior 11/16/2018
SECTION 530 - WATERPROOFING CONCRETE SURFACES
A. ITEM 530.3 - CEMENT BASE WITH ACRYLIC LATEX (2 Coats)
Manufacturer: Product:Thoroseal (Pearl Gray) w/Acryl 60BASF
Tamoseal (Oyster Gray) w/AKKRO-7TTamms Industries
B. ITEM 530.3 - CEMENT BASE, POLYMER MODIFIED (2 Coats)
Manufacturer: Product:Silcabond FCR 851 (Gray)Flexcrete Limited
Duraltop Coating (Gray)Tamms Industries
SECTION 532 - ANTI-GRAFFITI COATINGS
A. ITEM 532.1 - SEMI-PERMANENT ANTI-GRAFFITI COATINGS (CLEAR)
When specified, use a water repellant product listed under 534.B.
Issue 2016-01Page 11 of 30
Qualified Products List
SECTION 534 - WATER REPELLENT
A. Not currently used
B. ITEM 534.3 - SILANE/SILOXANE
Manufacturer: Product:
These products can be used when ambient and surface temperatures are 40 degrees and above.
SIL-ACT ATS-100 LVAdvanced Chemical Technologies, Inc.
SIL-ACT ATS-42AAdvanced Chemical Technologies, Inc.
Aquanil Plus 100ChemMasters
Armor SX 5000 EXT-100Foundation Armor, LLC.
Powerseal 40Vexcon Chemicals
C. ITEM 534.3 - SILANE/SILOXANE - COLD WEATHER
Manufacturer: Product:
These products can be used when ambient and surface temperatures are 20 degrees and above.
Certi-Vex Penseal 244 100%Vexcon Chemicals
Certi-Vex Penseal 244 40% AIMVexcon Chemicals
SECTION 538 - BARRIER MEMBRANE
A. ITEM 538.1 - BARRIER MEMBRANE, PEEL AND STICK
Manufacturer: Product:
For horizontal application only. Qualified for use on buried structures.
Products listed under 538.B may also be used for this item.
10 AN Easy Pave, 713A Primer, 104CM MasticRoyston Laboratories
(Membrane application temperature 40 Degrees F and rising)
B. ITEM 538.2 - BARRIER MEMBRANE, PEEL AND STICK - VERTICAL SURFACES
Manufacturer: Product:
These products may also be used for Item 538.1.
Jiffy Seal 140/60 Cold Weather, VOC 100 Primer, 160H Mastic
Protecto Wrap Co.
104-AHT, 740 Primer, 104CM MasticRoyston Laboratories Inc.
Lo Temp Membrane, Bituthene Primer B2, Bituthene MasticW.R.Grace
(Membrane application temperature 25 Degrees F and rising)
Issue 2016-01Page 12 of 30
Qualified Products List
C. PROTECTION BOARD FOR BARRIER MEMBRANE
Manufacturer: Product:
Use on membraned surfaces to be backfilled against.
1.0" Closed-Cell Extruded Polystyrene Board-
Bituthene Asphaltic HardboardW.R. Grace
Sealtight PC-2W.R. Meadows
D. Not currently used
E. HOT RUBBERIZED ASPHALT
Manufacturer: Product:
For use along curb line with Items 538.5 and 538.6
790-11 MTO GradeHenry Company
Hydrotech BDMHydrotech Membrane Corp.
MACSEAL BDM (formerly Bemalastic 1213 BDM)McAsphalt Industries, Limited
Ultraseal 3750Ultraseal Construction Products
Wabo ExpandexWatson Bowman Acme
F. ITEM 538.5 - BARRIER MEMBRANE, HEAT WELDED
Manufacturer: Product:Armour Bridge/Pont 4.5 mm *IKO Industries Ltd.
Sopralene Flam Antirock Membrane, Antirock Primer & Tackcoat
Soprema Roofing & Waterproofing Inc.
(Required Laydown Temperature - Hot Bituminous Pavement (538.3.5) = 290 - 330 deg. F)
* Use either Elastocol 500 Primer or Roofcraft Modified Asphalt Primer for both the primer and tack coat.
G. ITEM 538.6 - BARRIER MEMBRANE, HEAT WELDED - MACHINE METHOD
Manufacturer: Product:Armour Bridge/Pont 4.5 mm *IKO Industries Ltd.
Sopralene Flam Antirock Membrane, Antirock Primer & Tackcoat
Soprema Roofing & Waterproofing Inc.
(Required Laydown Temperature - Hot Bituminous Pavement (538.3.5) = 290 - 330 deg. F)
* Use either Elastocol 500 Primer or Roofcraft Modified Asphalt Primer for both the primer and tack coat.
H. Not currently used
Issue 2016-01Page 13 of 30
Qualified Products List
I. MOISTURE METER (For concrete bridge decks)
Manufacturer: Product:
Meters must be calibrated annually. A copy of the calibration certification shall accompany the meter.
Dual Probe Moisture MasterSovereign Chemical Industries, Ltd.
Tramex Concrete EncounterTramex, Ltd.
SECTION 541 - WATERSTOPS (PVC)
A. ITEM 541.1 - WATERSTOP, NH TYPE 1
Manufacturer: Product:DB-4316BoMetals, Inc
FR-4316BoMetals, Inc
721 (Ribbed Split), 741 (Dumbbell)Greenstreak
FR-4316 (Ribbed)Paul Murphy Plastics
D4-316 (Dumbbell)Vinylex
B. ITEM 541.2 - WATERSTOP, NH TYPE 2
Manufacturer: Product:RCB-938BRBoMetals, Inc.
703 (Ribbed), 723 (Ribbed Split)Greenstreak
CR-6316 (Ribbed), SR-6316 (Ribbed Split)Paul Murphy Plastics
RSB6-316 (Ribbed Split)Vinylex
C. ITEM 541.3 - WATERSTOP, NH TYPE 3
Manufacturer: Product:DBCB-614BoMetals, Inc
780 (Ribbed), 757 (Dumbbell)Greenstreak
CR-6380 (Ribbed), SR-6380 (Ribbed Split)Paul Murphy Plastics
RB6-14 (Ribbed), DBG-14 (Dumbbell)Vinylex
D. ITEM 541.4 - WATERSTOP, NH TYPE 4
Manufacturer: Product:DBCB-938BoMetals, Inc.
696 (Ribbed), 753 (Dumbbell)Greenstreak
725 (Split Ribbed Dumbbell)Greenstreak
RLB9-38 (Ribbed), DB9-38 (Dumbbell), DSB9-38 (Dumbbell-split)
Vinylex
Issue 2016-01Page 14 of 30
Qualified Products List
E. ITEM 541.5 - WATERSTOP, NH TYPE 5
Manufacturer: Product:RF-814BoMetals, Inc.
769 (Ribbed)Greenstreak
L85-14 (Ribbed)Vinylex
SECTION 544 - REINFORCEMENT FOR CONCRETE
A. SYNTHETIC FIBER REINFORCEMENT
Manufacturer: Product:
These products are qualified as being able to meet the requirements of Section 544 of the NHDOT Standard specifications for Road and Bridge Construction when used to control shrinkage cracking of fully supported slabs.
Masterfiber MAC100BASF
FORTA FERROFORTA Corporation
Strux 90/40 FibersW. R. Grace
SECTION 550 - STRUCTURAL STEEL
A. FAST SETTING GROUTS FOR ANCHOR BOLTS (550.3.15.4.2)
Manufacturer: Product:
These products are qualified as being able to meet the requirements of Section 550 of the Standard Specifications for Road and Bridge Construction, paragraph 550.3.15.4.2.
Super Por RokCGM, Inc.
Sure-Grip High Performance GroutDayton Superior
Commercial Grade FastSet Non-Shrink GroutQuikrete
B. STICK WAX FOR HIGH STRENGTH A325 & A490 FASTENERS
Manufacturer: Product:Stick Wax LubricantCastrol Industrial of North America
TrueTap Wax StickCRC Industries, Inc.
Stick KutRelton
Issue 2016-01Page 15 of 30
Qualified Products List
SECTION 559 - ASPHALTIC PLUG EXPANSION JOINT, ASPHALTIC PLUG CRACK
A. ITEM 559.4 - ASPHALTIC PLUG EXPANSION JOINT (formerly "Elastomeric Plug Type Expansion Joint")
Manufacturer: Product:Matrix 502 Asphaltic Expansion Joint System w/ Matrix 502 binder
D.S. Brown
Thorma-Joint Asphaltic Plug Expansion Joint w/ BJ Super Binder
Dynamic Surface Applications, Ltd.
Wabo Expandex Asphaltic Plug Joint System w/Expandex Binder
Watson Bowman Acme
B. Not currently used
C. ITEM 559.41 - ASPHALTIC PLUG FOR CRACK CONTROL (formerly "Modified Elastomeric Plug Type Expansion Joint - 6" wide)
Use the binder and aggregate from one of the joint systems that are listed under 559.A.
D. ITEM 559.412 - REPAIR ASPHALTIC PLUG EXPANSION JOINT (Formerly Modified Elastomeric Plug Type Expansion Joint - 20" Wide)
Use the binder and aggregate from one of the joint systems that are listed under 559.A.
E. CLOSED CELL EXPANSION MATERIAL
Manufacturer: Product:EVA-SEAL 30/FlexsealChase Construction Products
MetazealChase Construction Products
Phyzite 380 w/HALSChase Construction Products
Ply-SealPolyset Company
Ply-Seal FB, HALSPolyset Company
Ply-Seal FGPolyset Company
Wabo EvazoteWatson Bowman Acme
Issue 2016-01Page 16 of 30
Qualified Products List
SECTION 560 - PREFABRICATED COMPRESSION SEAL EXPANSION JOINT
A. PREFABRICATED COMPRESSION SEAL EXPANSION JOINT
Manufacturer: Product:Delastic "CV" and "CA" SeriesD.S. Brown
WA SeriesWatson Bowman Acme
SECTION 561 - PREFABRICATED EXPANSION JOINT
A. PREFAB. STRIP SEAL EXPANSION JOINT
Manufacturer: Product:A2R-400 (SSA2 Steelflex rail profile)D.S. Brown
SE-400 ("A" steel edge member)Watson Bowman Acme
B. PREFAB. MODULAR BRIDGE JOINT SYSTEM
Manufacturer: Product:D SeriesD.S. Brown
STM SeriesWatson Bowman Acme
C. PREFORMED FABRIC TROUGH (Used with prefabricated finger joints)
Manufacturer: Product:Flexible Drain TroughFabreeka Products Co.
3-ply PNT 50 Saniwhite 3/64 x FSThermoid of H.B.D. Industries, Inc.
SECTION 562 - SILICONE JOINT SEALANT
A. SILICONE JOINT SEALANT (Non-sag, for vertical and horizontal joints).
Manufacturer: Product:
The use of primer is required with these products unless waived by the Engineer.
Dow Corning 888 (Non-sag, for vertical and horizontal joints)Dow Corning Corp.
Sikasil-728 NSSika Corporation
Issue 2016-01Page 17 of 30
Qualified Products List
B. SILICONE JOINT SEALANT (Self-leveling, for horizontal joints)
Manufacturer: Product:
The use of primer is required with these products unless waived by the Engineer.
Dow Corning 890-SL (Self-leveling, for horizontal joints only)Dow Corning Corp.
Sikasil-728 SLSika Corporation
SECTION 593 - GEOTEXTILES
A. ITEM 593.ABC - GEOTEXTILES
Note: Products must be tested by the AASHTO National Transportation Product Evaluation Program (NTPEP) which requires retesting every 3 years. Products are considered to be qualified only through the indicated expiration date.
See the following tables for qualified products and their application, strength, and structure.
Issue 2016-01Page 18 of 30
A. ITEM 593.ABC - GEOTEXTILES
A= Application B= Strength Class C= Structure
1 = Subsurface Drainage
2 = Separation
0 = Class 0 (Extra High Strength)
1 = Class 1 (High Strength)
0 = Contractor Option
1 = Nonwoven (Default - Applic. 1 & 4)
3 = Stabilization
4 = Permanent Erosion Control
2 = Class 2 (Medium Strength)
3 = Class 3 (Low Strength)
2 = Monofilament, Woven
3 = Slit Filament, Woven
Note: In addition to being listed here, manufacturers of geotextiles are required to participate in and maintaincompliance with the AASHTO National Transportation Product Evaluation Program that audits producers of geotextiles.
Manufacturer & Product Qualified For
Advanced Drainage System Expiration Date
AApplication
BStrength Class
CStructure
104F 1/1/2019 2,3 2,3 2
Belton Industries, Inc. Expiration Date
AApplication
BStrength Class
CStructure
Beltech 315, Style 977 1/1/2017 2,3 1,2,3 3
Carthage Mills Expiration Date
AApplication
BStrength Class
CStructure
FX-160HS 1/1/2017 1,2,3,4 0,1,2,3 1
FX-45HS 1/1/2017 1,2,3 3 1
FX-55 1/1/2017 2,3 3 3
FX-60HS 1/1/2017 1,2,3,4 2,3 1
FX-66 1/1/2017 2,3 1,2,3 3
FX-80HS 1/1/2017 1,2,3,4 1,2,3 1
Crown Resources Expiration Date
AApplication
BStrength Class
CStructure
R070 1/1/2017 1,2,3,4 2,3 1
R100 1/1/2017 1,2,3,4 1,2,3 1
R120 1/1/2017 1,2,3,4 1,2,3 1
R160 1/1/2017 1,2,3,4 1,2,3 1
R042 1/1/2018 1,2,3 3 1
R060 1/1/2018 1,2,3,4 2,3 1
R080 1/1/2018 1,2,3,4 1,2,3 1
Issue 2016-01Page 19 of 30
A. ITEM 593.ABC - GEOTEXTILES
A= Application B= Strength Class C= Structure
1 = Subsurface Drainage
2 = Separation
0 = Class 0 (Extra High Strength)
1 = Class 1 (High Strength)
0 = Contractor Option
1 = Nonwoven (Default - Applic. 1 & 4)
3 = Stabilization
4 = Permanent Erosion Control
2 = Class 2 (Medium Strength)
3 = Class 3 (Low Strength)
2 = Monofilament, Woven
3 = Slit Filament, Woven
Note: In addition to being listed here, manufacturers of geotextiles are required to participate in and maintaincompliance with the AASHTO National Transportation Product Evaluation Program that audits producers of geotextiles.
Manufacturer & Product Qualified For
Hanes Geo Components Expiration Date
AApplication
BStrength Class
CStructure
TerraTex GS 1/1/2017 2,3 3 3
Terratex GS-250 1/1/2017 2,3 2,3 3
Terratex HD 1/1/2017 2,3 1,2,3 3
TerraTex N06 1/1/2017 1,2,3,4 2,3 1
Terratex N07 1/1/2017 1,2,3,4 2,3 1
Terratex N08 1/1/2017 1,2,3,4 1,2,3 1
Terratex N16 1/1/2017 1,2,3,4 0,1,2,3 1
TerraTex N4.5 1/1/2017 1,2,3 3 1
L&M Supply Co. Expiration Date
AApplication
BStrength Class
CStructure
LM 2199 FW 1/1/2019 2,3 2,3 2
Propex Operating Company, LLC Expiration Date
AApplication
BStrength Class
CStructure
Geotex 200ST 1/1/2017 2,3 3 3
Geotex 250ST 1/1/2019 2,3 2,3 3
Geotex 501 1/1/2019 1,2,3,4 3 1
Geotex 601 1/1/2019 1,2,3,4 2,3 1
Geotex 701 1/1/2019 1,2,3,4 2,3 1
Geotex 801 1/1/2019 1,2,3,4 1,2,3 1
Issue 2016-01Page 20 of 30
A. ITEM 593.ABC - GEOTEXTILES
A= Application B= Strength Class C= Structure
1 = Subsurface Drainage
2 = Separation
0 = Class 0 (Extra High Strength)
1 = Class 1 (High Strength)
0 = Contractor Option
1 = Nonwoven (Default - Applic. 1 & 4)
3 = Stabilization
4 = Permanent Erosion Control
2 = Class 2 (Medium Strength)
3 = Class 3 (Low Strength)
2 = Monofilament, Woven
3 = Slit Filament, Woven
Note: In addition to being listed here, manufacturers of geotextiles are required to participate in and maintaincompliance with the AASHTO National Transportation Product Evaluation Program that audits producers of geotextiles.
Manufacturer & Product Qualified For
SKAPS Industries Expiration Date
AApplication
BStrength Class
CStructure
SW200 1/1/2017 2,3 3 3
SW315 1/1/2017 2,3 1,2,3 3
W25 1/1/2017 2,3 2,3 3
W270 1/1/2017 2,3 2.3 3
GT116 1/1/2018 1,2,3,4 0,1,2,3 1
GT142 1/1/2018 1,2,3 3 1
GT160 1/1/2018 1,2,3,4 2.3 1
GT170 1/1/2018 1,2,3,4 2,3 1
GT180 1/1/2018 1,2,3,4 1,2,3 1
TenCate Geosynthetics North America Expiration Date
AApplication
BStrength Class
CStructure
Mirafi 500X 1/1/2017 2,3 3 3
Mirafi 160N 1/1/2018 1,2,3,4 2,3 1
Mirafi 180N 1/1/2018 1,2,3,4 1,2,3 1
Mirafi 600X 1/1/2018 2,3 1,2,3 3
Mirafi 140N 1/1/2019 1,2,3 3 1
Mirafi FW402 1/1/2019 2,3 3 2
Mirafi FW404 1/1/2019 2,3 1,2,3 2
Thrace-LINQ Expiration Date
AApplication
BStrength Class
CStructure
Civil Non-Woven 350EX 1/1/2018 1,2,3,4 0,1,2,3 1
140EX 1/1/2019 1,2,3 3 1
Issue 2016-01Page 21 of 30
A. ITEM 593.ABC - GEOTEXTILES
A= Application B= Strength Class C= Structure
1 = Subsurface Drainage
2 = Separation
0 = Class 0 (Extra High Strength)
1 = Class 1 (High Strength)
0 = Contractor Option
1 = Nonwoven (Default - Applic. 1 & 4)
3 = Stabilization
4 = Permanent Erosion Control
2 = Class 2 (Medium Strength)
3 = Class 3 (Low Strength)
2 = Monofilament, Woven
3 = Slit Filament, Woven
Note: In addition to being listed here, manufacturers of geotextiles are required to participate in and maintaincompliance with the AASHTO National Transportation Product Evaluation Program that audits producers of geotextiles.
Manufacturer & Product Qualified For
US Fabrics Expiration Date
AApplication
BStrength Class
CStructure
US 120NW 1/1/2017 1,2,3 3 1
US 160NW 1/1/2017 1,2,3,4 2,3 1
US 200 1/1/2017 2,3 3 3
US 205NW 1/1/2017 1,2,3,4 1,2,3 1
US 230 1/1/2017 2,3 1,2,3 2
US 230C 1/1/2017 2,3 1,2,3 2
US 250 1/1/2017 2,3 2,3 3
US 315 1/1/2017 2,3 1,2,3 3
US 380NW 1/1/2017 1,2,3,4 0,1,2,3 1
Western Excelsior Expiration Date
AApplication
BStrength Class
CStructure
Excel 16.0N 1/1/2017 1,2,3,4 0,1,2,3 1
Willacoochee Industrial Fabrics, Inc Expiration Date
AApplication
BStrength Class
CStructure
WINFAB 450N 1/1/2017 1,2,3 3 1
WINFAB 600N 1/1/2017 1,2,3,4 2,3 1
WINFAB 700N 1/1/2017 1,2,3,4 2,3 1
WINFAB 800N 1/1/2017 1,2,3,4 1,2,3 1
200W 1/1/2018 2,3 3 3
250W 1/1/2018 2,3 2,3 3
315W 1/1/2018 2,3 1,2,3 3
WINFAB 2199 1/1/2019 2,3 2,3 2
WINFAB 2404 1/1/2019 2,3 1,2,3 2
Issue 2016-01Page 22 of 30
Qualified Products List
SECTION 604 - CATCH BASINS, DROP INLETS, AND MANHOLES
A. FIBER REINFORCEMENT FOR PRECAST DRAINAGE STRUCTURES
Manufacturer: Product:
Note: Use of fiber reinforcement is only allowed for drainage structures with a maximum diameter of 4'.
Masterfiber MAC100BASF
FORTA FERROFORTA Corporation
Strux 90/40 FibersW.R. Grace
SECTION 606 - GUARDRAIL
A. SYNTHETIC OFFSET BLOCKS
Manufacturer: Product:
Block dimensions must be as indicated on the standard plan sheet for the item.
Mondo BlockMondo Polymer Technologies
P-Block SeriesMonroeville Industrial Molding, Inc.
Modified King BlockTrinity Highway Products
B. ITEM 606.9512 - TEMPORARY IMPACT ATTENUATION DEVICE (Redirective), Test Level 2
Manufacturer: Product:Universal Tau-IIBarrier Systems, Inc.
QuadguardEnergy Absorption Systems, Inc.
TRACC, WideTRACC, FastTRACC, ShortTRACCTrinity Industries, Inc.
SCI 100 GMWork Area Protection Corp.
C. ITEM 606.9513 - TEMPORARY IMPACT ATTENUATION DEVICE (Redirective), Test Level 3
Manufacturer: Product:Universal Tau-IIBarrier Systems, Inc.
QuadGuardEnergy Absorption Systems, Inc.
TRACC, WideTRACC, FastTRACC, ShortTRACCTrinity Industries, Inc.
SCI 100 GMWork Area Protection Corp.
D. ITEM 606.9522 - TEMPORARY IMPACT ATTENUATION DEVICE (Non-redirective), Test Level 2
Manufacturer: Product:
Sand or liquid filled devices may be used when allowed by specification. A product listed under B. ITEM 606.9512 - TEMPORARY IMPACT ATTENUATION DEVICE (Redirective), Test Level 2 may also be used.
N.E.A.T.Energy Absorbtion Systems, Inc.
Issue 2016-01Page 23 of 30
Qualified Products List
E. ITEM 606.9523 - TEMPORARY IMPACT ATTENUATION DEVICE (Non-redirective), Test Level 3
Sand or liquid filled devices may be used when allowed by specification. When sand or liquid filled devices are not allowed by specification, use a product listed under C. ITEM 606.9513 - TEMPORARY IMPACT ATTENUATION DEVICE (Redirective), Test Level 3.
SECTION 609 - CURBS
A. NON-SHRINK, NON-METALLIC GROUT (Cement Mortar for Bedding Curb; Bridge)
Manufacturer: Product:Harris Construction GroutA.H. Harris
Enduro #50Conspec Marketing & Manufacturing Co
1107 Advantage GroutDayton Superior
Structural ConcreteFive Star Products
B. POLYESTER FIBERS FOR BITUMINOUS CURB
Manufacturer: Product:P1251 Polyester FibersAdvanced Fiber Solutions, Inc.
P440 Fibers, White or BlackAdvanced Fiber Solutions, Inc.
Petroflex Type 450GFC Materials Co.
Boni Fibers Type BKapejo Inc.
SECTION 616 - TRAFFIC SIGNALS
A. SAW CUT LOOP SEALANT
Manufacturer: Product:Bondo Traffic P-606 Flexible Loop Sealer3M
Stat-A-Flex Loop SealerDurant Performance Coatings
Pro-Seal 6006RAI Products, Inc.
Issue 2016-01Page 24 of 30
Qualified Products List
SECTION 619 - MAINTENANCE OF TRAFFIC
A. TEMPORARY RAISED PAVEMENT MARKERS
Manufacturer: Product:Apex Model 932 Chip Seal Marker *Apex Universal, Inc.
Model TPMAstro Optics Corp.
Halftrack MarkerPEXCO LLC, Davidson Traffic Control
RPM Durable Pavement MarkerPEXCO LLC, Davidson Traffic Control
TOM Road Marker *PEXCO LLC, Davidson Traffic Control
* Not for use on Interstates or other divided highway facilities.
SECTION 632 - RETROREFLECTIVE PAVEMENT MARKINGS
A. ITEM 632.1 - PREFORMED RETROREFLECTIVE TAPE, TYPE I (REMOVABLE)
Manufacturer: Product:
These products are consdiered to be "wet reflective"
Stamark Wet Reflective Removable Tape Series 710 - White & Yellow
3M
Deltaline TWR - White & YellowBriteline Technologies, Inc.
B. Not Currently Used
C. ITEM 632.5 - PREFORMED RETROREFLECTIVE TAPE, LEVEL I
Manufacturer: Product:Series 380-I ES - White & Yellow3M
Stamark High Performance Tape Series 380AW - White3M
Deltaline XRP - White & YellowBriteline Technologies, Inc.
D. ITEM 632.6 - PREFORMED RETROREFLECTIVE TAPE, LEVEL II
Manufacturer: Product:Series 380-I ES - White & Yellow3M
Brite-Line Series 1000 Durable Tape - White & YellowBriteline Technologies, Inc.
Deltaline HDX - White & YellowBriteline Technologies, Inc.
Issue 2016-01Page 25 of 30
Qualified Products List
E. Not currently used
F. ITEM 632.9 - PREFORMED BLACKOUT TAPE, TYPE I (REMOVABLE)
Manufacturer: Product:
Note: This category is for temporary obliteration of pavement markings.
3M Stamark Removable Black Line Mask 7153M
ATM 280 Hide A LineAdvance Traffic Markings
Deltaline BTRBrite-Line Technologies, Inc.
SECTION 645 - EROSION CONTROL
A. through G. These categories are not currently used.
H. TACKIFIERS
Manufacturer: Product:
For specific product information, contact the Roadside Development Section, Bureau of Highway Design, 271-6476.
Prior to use, verify conformance with applicable environmental regulations.
StarTak 100CHEMSTAR
StarTak 600CHEMSTAR
Ecotak OPEastern Products, Inc.
Ecotak SatEastern Products, Inc.
Qualified products shall be used in accordance with the manufacturer's specified conditions & installed as directed by the manufacturer.
These conditions & installation instructions shall be furnished to the Engineer at least 10 working days prior to actual delivery & installation on the project.
I. Not currently used.
Issue 2016-01Page 26 of 30
Qualified Products List
J. ITEM 645.41 - TEMPORARY SLOPE STABILIZATION TYPE A
Manufacturer: Product:
Note: Products must be tested by the AASHTO National Transportation Product Evaluation Program (NTPEP) which requires retesting every 3 years. Products are considered to be qualified only through the indicated expiration date.
Expiration Date:AEC Premier Straw Double NetAmerican Excelsior Company 1/1/2017
AEC Premier Straw Single NetAmerican Excelsior Company 1/1/2017
Curlex I CLAmerican Excelsior Company 1/1/2017
Curlex IIAmerican Excelsior Company 1/1/2017
Curlex II .98American Excelsior Company 1/1/2018
ECS-2East Coast Erosion Blankets 1/1/2017
C4000Enviroscape ECM, Ltd. 1/1/2017
S2000Enviroscape ECM, Ltd. 1/1/2018
SC3000Enviroscape ECM, Ltd. 1/1/2017
S150North American Green 1/1/2017
Excel CS-3Western Excelsior 1/1/2017
Excel SR-1Western Excelsior 1/1/2017
Excel SS-2Western Excelsior 1/1/2017
K. ITEM 645.42 - TEMPORARY SLOPE STABILIZATION TYPE B (Wildlife friendly)
Manufacturer: Product:
Note: Products must be tested by the AASHTO National Transportation Product Evaluation Program (NTPEP) which requires retesting every 3 years. Products are considered to be qualified only through the indicated expiration date.
These products may also be used for Item 645.41.
Expiration Date:Curlex I FibreNetAmerican Excelsior Company 1/1/2017
ECS-2BEast Coast Erosion Blankets, LLC 1/1/2017
S32 BDErosion Control Blanket 1/1/2017
S150BNNorth American Green 1/1/2017
Excel CS-3 All NaturalWestern Excelsior 1/1/2018
Excel S-2 All NaturalWestern Excelsior 1/1/2017
Excel SS-2 All NaturalWestern Excelsior 1/1/2018
Issue 2016-01Page 27 of 30
Qualified Products List
L. ITEM 645.43 - TEMPORARY SLOPE STABILIZATION TYPE C
Manufacturer: Product:
Note: Products must be tested by the AASHTO National Transportation Product Evaluation Program (NTPEP) which requires retesting every 3 years. Products are considered to be qualified only through the indicated expiration date.
These products may also be used for Item 645.41.
Expiration Date:AEC Premier CoconutAmerican Excelsior Company 1/1/2017
AEC Premier Straw/CoconutAmerican Excelsior Company 1/1/2017
Curlex High VelocityAmerican Excelsior Company 1/1/2017
Curlex II CLAmerican Excelsior Company 1/1/2017
Curlex IIIAmerican Excelsior Company 1/1/2017
ECC-2East Coast Erosion Blankets, LLC 1/1/2017
ECSC-2East Coast Erosion Blankets, LLC 1/1/2017
SC32Erosion Control Blanket 1/1/2017
C125North American Green 1/1/2017
SC150North American Green 1/1/2017
Excel S-2Western Excelsior 1/1/2017
Excel SD-3Western Excelsior 1/1/2017
M. ITEM 645.44 - TEMPORARY SLOPE STABILIZATION TYPE D (Wildlife friendly)
Manufacturer: Product:
Note: Products must be tested by the AASHTO National Transportation Product Evaluation Program (NTPEP) which requires retesting every 3 years. Products are considered to be qualified only through the indicated expiration date.
These products may also be used for Item 645.43.
Expiration Date:AEC Premier Coconut FibreNetAmerican Excelsior Company 1/1/2017
AEC Premier Straw/Coconut FibreNetAmerican Excelsior Company 1/1/2017
Curlex II FibreNetAmerican Excelsior Company 1/1/2017
ECC-2BEast Coast Erosion Blankets, LLC 1/1/2017
ECSC-2BEast Coast Erosion Blankets, LLC 1/1/2017
C32BDErosion Control Blanket 1/1/2017
SC32 BDErosion Control Blanket 1/1/2017
C125BNNorth American Green 1/1/2017
SC150BNNorth American Green 1/1/2017
Excel CC-4 All NaturalWestern Excelsior 1/1/2018
N. ITEM 645.45 - PERMANENT CHANNEL STABILIZATION TYPE A
Manufacturer: Product:
Note: Products must be tested by the AASHTO National Transportation Product Evaluation Program (NTPEP) which requires retesting every 3 years. Products are considered to be qualified only through the indicated expiration date.
Expiration Date:RecyclexAmerican Excelsior Company 1/1/2017
P550North American Green 1/1/2018
Issue 2016-01Page 28 of 30
Qualified Products List
O. ITEM 645.46 - PERMANENT CHANNEL STABILIZATION TYPE B
Manufacturer: Product:
Note: Products must be tested by the AASHTO National Transportation Product Evaluation Program (NTPEP) which requires retesting every 3 years. Products are considered to be qualified only through the indicated expiration date.
These products may also be used for Item 645.45
Expiration Date:ECP-3East Coast Erosion Blankets, LLC 1/1/2018
P550North American Green 1/1/2018
LandLok 300Propex, Inc. 1/1/2017
Landlok TRM 450Propex, Inc. 1/1/2017
PyramatPropex, Inc. 1/1/2017
SECTION 718 - RETROREFLECTIVE SHEETING
A. Not currently used
B. Not currently used
C. RETROREFLECTIVE SHEETING - TYPE IV
Manufacturer: Product:High Intensity Prismatic Reflective Sheeting 39303M
T-6500Avery Dennison
D. RETROREFLECTIVE SHEETING - TYPE VIII
Manufacturer: Product:
Unless otherwise specified, Type VIII, and Type IX can be used interchangeably.
3M Prismatic Reflective Sheeting Series 39403M
T-7500Avery Dennison
Nikkalite Crystal Grade Reflective Sheeting 92000 SeriesNippon Carbide Industries
Issue 2016-01Page 29 of 30
Qualified Products List
E. RETROREFLECTIVE SHEETING - TYPE IX
Manufacturer: Product:
Unless otherwise specified, Type VIII and Type IX can be used interchangeably.
Diamond Grade VIP Reflective Sheeting Series 39903M
OmniCube (T-11500) SeriesAvery Dennison
T-9500Avery Dennison
F. Not currently used
G. OVERLAY FILM
Manufacturer: Product:Electrocut 1170 Series - Yellow, Blue, Green, Red3M
OL-2000 Series - Yellow, Blue, Green, Red, BrownAvery Dennison
H. RETROREFLECTIVE SHEETING - TYPE XI
Manufacturer: Product:3M Diamond Grade DG3 Reflective Sheeting Series 40003M
OmniCube (T-11500) SeriesAvery Dennison
Issue 2016-01Page 30 of 30