Q921 rfp lec2 v1
-
Upload
hossein-alaminia -
Category
Education
-
view
169 -
download
2
Transcript of Q921 rfp lec2 v1
Reservoir Fluid Properties Course (2nd Ed.)
2013H. AlamiNia Reservoir Fluid Properties Course: Petroleum Reservoir Fluids 2
1. Reservoir Fluids
2. Phase Behavior of Hydrocarbons
3. Phase Envelopes
2013H. AlamiNia Reservoir Fluid Properties Course: Petroleum Reservoir Fluids 3
Reservoir Fluid Constituents
Petroleum reservoir fluids are multicomponent mixtures consisting primarily of hydrocarbons.Methane (CH4) is the simplest of all hydrocarbons, and
also the most common component in petroleum reservoir fluids. Because methane contains one carbon atom, it is often referred to as C1.
Hydrocarbons with seven and more carbon atoms are called C7+ components, and the entity of all C7+ components is called the C7+ fraction.
Petroleum reservoir fluids may contain hydrocarbons as heavy as C 200.
2013H. AlamiNia Reservoir Fluid Properties Course: Petroleum Reservoir Fluids 5
C7+ Components
A particular C7+ component will belong to one of the following component classes: Paraffins: A paraffinic compound consists of hydrocarbon segments
of the type C, CH, CH 2, or CH 3. The carbon atoms are connected by single bonds. Paraffins are also sometimes referred to as alkanes.
Naphthenes: These compounds are similar to paraffins in the sense that they are built of the same types of hydrocarbon segments, but they differ from paraffins by containing one or more cyclic structures. Naphthenes are also called cycloalkanes.
Aromatics: Similar to naphthenes, aromatics contain one or more cyclic structures, but the carbon atoms in an aromatic compound are connected by aromatic double bonds.
The percentage contents of paraffinic (P), naphthenic (N), and aromatic (A) components in a reservoir fluid is often referred to as the PNA distribution.
2013H. AlamiNia Reservoir Fluid Properties Course: Petroleum Reservoir Fluids 6
Molecular Structures
Molecular Structures of Some Petroleum Reservoir Fluid
Constituents
2013H. AlamiNia Reservoir Fluid Properties Course: Petroleum Reservoir Fluids 7
Non HC Components
Petroleum reservoir fluids may also contain inorganic compounds, of whichNitrogen (N 2), Carbon dioxide (CO 2), And hydrogen sulfide (H 2 S)
Are the most common.
Water (H 2 O) is another important reservoir fluid constituent. As water has limited miscibility with hydrocarbons, most of the water in a reservoir is usually found in a separate water zone located beneath the gas and oil zones.
2013H. AlamiNia Reservoir Fluid Properties Course: Petroleum Reservoir Fluids 8
Phase Behavior Definition
A "phase" is defined as any homogeneous part of a system that is physically distinct and separated from other parts of the system by definite boundaries. For example, ice, liquid water, and water vapor
constitute three separate phases of the pure substance H20. Whether a substance exists in a solid, liquid, or gas
phase is determined by the temperature and pressure acting on the substance. It is known that ice (solid phase) can be changed to
water (liquid phase) by increasing its temperature and, by further increasing temperature, water changes to steam (vapor phase). This change in phases is termed Phase Behavior.
2013H. AlamiNia Reservoir Fluid Properties Course: Petroleum Reservoir Fluids 10
Properties of Reservoir Fluid ConstituentsThe pure component vapor pressures and the pure
component critical points are essential in calculations of component and mixture properties.
The pure component vapor pressures are experimentally determined by measuring corresponding values of temperature (T) and pressure (P) at which the substance undergoes a transition from liquid to gas.
2013H. AlamiNia Reservoir Fluid Properties Course: Petroleum Reservoir Fluids 11
Single-Component Systems
The simplest type of hydrocarbon system to consider is that containing one component. The word ''component'' refers to the number of molecular or atomic species present in the substance. A single-component system is composed entirely of one kind of atom or molecule. We often use the word "pure'' to describe a single-component system.
2013H. AlamiNia Reservoir Fluid Properties Course: Petroleum Reservoir Fluids 12
Qualitative Understanding
The qualitative understanding of the relationship between temperature T, pressure p, and volume V of pure components can provide an excellent basis for understanding the phase behavior of complex petroleum mixtures.
The foregoing relationship is conveniently introduced in terms of experimental measurements conducted on a pure component as the component is subjected to changes in pressure and volume at constant temperature.
2013H. AlamiNia Reservoir Fluid Properties Course: Petroleum Reservoir Fluids 13
P-V Diagram for a Single Component System
2013H. AlamiNia Reservoir Fluid Properties Course: Petroleum Reservoir Fluids 14
Isothermal Paths
Suppose a fixed quantity of a pure component is placed in a cylinder fitted with a frictionless piston at a fixed temperature T 1. Consider the initial p exerted on the system to be low enough that the entire system is in the vapor state (E).
Step 1. The pressure is increased isothermally (F). On the diagram, where the liquid begins to condense.
The corresponding pressure is known as the dew-point pressure Pd, and is defined as the pressure at which the first droplet of liquid is formed.
2013H. AlamiNia Reservoir Fluid Properties Course: Petroleum Reservoir Fluids 15
Isothermal Paths (Cont.)
Step 2. The piston is moved further into the cylinder as more liquid condenses. This condensation process is characterized by a constant pressure and represented by the horizontal line FG.
At point G, traces of gas remain and the corresponding pressure is called the bubble-point pressure Pb, and defined as the pressure at which the first sign of gas formation is detected.
A characteristic of a single-component system is that at a given temperature, the dew-point pressure and the bubble-point pressure are equal.
Step 3. As the piston is forced slightly into the cylinder, a sharp increase in the pressure (point H) is noted without an appreciable decrease in the liquid volume. That behavior evidently reflects the low compressibility of the liquid phase.
2013H. AlamiNia Reservoir Fluid Properties Course: Petroleum Reservoir Fluids 16
Isothermal Paths (Cont.)
By repeating the above steps at progressively increasing temperatures, a family of curves of equal temperatures (isotherms) is constructed. The dashed curve connecting the dew points is called
the dew-point curve (line FC) and represents the states of the ''saturated gas."
The dashed curve connecting the bubble points is called the bubble-point curve (line GC) and similarly represents the "saturated liquid."
These two curves meet at point C which is known as the critical point. The corresponding pressure and volume are called the critical pressure Pc and critical volume V, respectively.
2013H. AlamiNia Reservoir Fluid Properties Course: Petroleum Reservoir Fluids 17
P-T Diagram for a Pure Component System.
2013H. AlamiNia Reservoir Fluid Properties Course: Petroleum Reservoir Fluids 18
Binary Systems (Two-Component Systems)Methane and benzene, both common constituents
of oil and gas mixtures.
The vapor pressure curve ends in the critical point (CP), above which no liquid- to gas-phase transition can take place.
Vapor pressure curves of methane and benzene (full-drawn line). Phase envelope (dashed line) of a mixture of 25 mol% methane and 75 mol% benzene calculated using the Soave–Redlich–Kwong equation of state.
2013H. AlamiNia Reservoir Fluid Properties Course: Petroleum Reservoir Fluids 19
Vapor Pressure Curves of Methane and Benzene
2013H. AlamiNia Reservoir Fluid Properties Course: Petroleum Reservoir Fluids 20
The Phase Behavior of a Pure ComponentAt a given temperature, T 1, may be studied by placing
a fixed amount of this component in a cell kept at the temperature T 1. The cell volume may be varied by moving the piston up and down. At position A, the cell content is in a gaseous state. If the
piston is moved downwards, the volume will decrease and the pressure increase.
At position B a liquid phase starts to form.
By moving the piston further downwards, the volume will further decrease, but the pressure will remain constant until all gas is converted into liquid. This happens at position C.
A further decrease in the cell volume will result in a rapidly increasing pressure.
2013H. AlamiNia Reservoir Fluid Properties Course: Petroleum Reservoir Fluids 21
Pure Component Phase Behavior in PT and PV Diagrams
Related to previous and next slides.
2013H. AlamiNia Reservoir Fluid Properties Course: Petroleum Reservoir Fluids 22
The Phase Behavior of a Pure Component (Cont.)The left-hand-side curve illustrates the phase changes
when crossing a vapor pressure curve. A pure component can only exist in the form of two phases in equilibrium right at the vapor pressure curve. When the vapor pressure curve is reached, a
conversion from either gas to liquid or liquid to gas will start. This phase transition is associated with volumetric changes at constant T and P. At the point B the component is said to be at its dew point or
in the form of a saturated gas. At position C the component is at its bubble point or in the
form of a saturated liquid. At position A the state is undersaturated gas, and at D it is
undersaturated liquid.
2013H. AlamiNia Reservoir Fluid Properties Course: Petroleum Reservoir Fluids 23
2013H. AlamiNia Reservoir Fluid Properties Course: Petroleum Reservoir Fluids 25
Phase Envelopes
Petroleum reservoir fluids are multicomponent mixtures, and it is therefore of much interest to look for the mixture equivalent of the pure component vapor pressure curve.
With two or more components present, the two-phase region is not restricted to a single line in a PT diagram.
As is illustrated for a mixture of 25 mol% methane and 75 mol% benzene, the two-phase region of a mixture forms a closed area in P and T.
The line surrounding this area is called the phase envelope.
2013H. AlamiNia Reservoir Fluid Properties Course: Petroleum Reservoir Fluids 26
Composition of Natural Gas Mixture
The phase envelope has been calculated using the Soave–Redlich–
Kwong equation of state
2013H. AlamiNia Reservoir Fluid Properties Course: Petroleum Reservoir Fluids 27
Phase Envelopes (Cont.)
Next slide shows the phase envelope of a natural gas mixture of the composition given in previous slide. The phase envelope consists of a dew point branch and
a bubble point branch meeting in the mixture critical point. At the dew point branch the mixture is in gaseous form
in equilibrium with an incipient amount of liquid. At these conditions the gas (or vapor) is said to be saturated. At higher temperatures at the same pressure, there is
no liquid present. On the contrary, the gas may take up liquid
components without liquid precipitation taking place. The gas is therefore said to be undersaturated.
2013H. AlamiNia Reservoir Fluid Properties Course: Petroleum Reservoir Fluids 28
Phase Envelope of Natural Gas
2013H. AlamiNia Reservoir Fluid Properties Course: Petroleum Reservoir Fluids 29
Phase Envelopes (Cont.)
At the bubble point branch the mixture is in liquid form in equilibrium with an incipient amount of gas, and the liquid is said to be saturated. At lower temperatures, at the same pressure the liquid
(or oil) is undersaturated. Right at the critical point, two identical phases are in
equilibrium, both having a composition equal to the overall composition. At temperatures close to the critical one and pressures
above the critical pressure there is only one phase present, but it can be difficult to tell whether it is a gas or a liquid. This term super-critical fluid is often used the super-critical region.
2013H. AlamiNia Reservoir Fluid Properties Course: Petroleum Reservoir Fluids 30
Phase Envelopes (Cont.)
The highest pressure at which two phases can exist is called the cricondenbar and the highest temperature with two phases present is called the cricondentherm. The phenomenon called retrograde condensation is as
a dashed vertical line at T = -30°C. At this temperature, the mixture is in gaseous form at pressures above the upper dew point pressure, i.e., at pressures above approximately 75 bar. At lower pressure, the mixture will split into two
phases, a gas and a liquid. Liquid formation taking place as the result of a falling pressure is called retrograde condensation. If the pressure at a constant temperature is decreased to below the lower dew point pressure of approximately 15 bar, the liquid phase will disappear, and all the mixture will be in gaseous form again.
2013H. AlamiNia Reservoir Fluid Properties Course: Petroleum Reservoir Fluids 31
2013H. AlamiNia Reservoir Fluid Properties Course: Petroleum Reservoir Fluids 32
1. Pedersen, K.S., Christensen, P.L., and Azeem, S.J. (2006). Phase behavior of petroleum reservoir fluids (CRC Press). Ch1.
2. Tarek, A. (1989). Hydrocarbon Phase Behavior (Gulf Publishing Company, Houston). Ch1.
2013H. AlamiNia Reservoir Fluid Properties Course: Petroleum Reservoir Fluids 33