PW50Y PW50 Owners Manual - Yamaha
-
Upload
nguyentram -
Category
Documents
-
view
227 -
download
0
Transcript of PW50Y PW50 Owners Manual - Yamaha
5PG-28199-18
PW50Y
OWNER’S MANUAL
Read this manual carefully before operating this vehicle.
LIT-11626-22-24
EAU10042
Read this manual carefully before operating this vehicle. This manual should stay with this vehicle if it is sold.
Q
INTRODUCTION
EAU41062
Congratulations on your purchase of the Yamaha PW50(Y). This model is the result of Yamaha’s vast experience in the pro-duction of fine sporting, touring, and pacesetting racing machines. It represents the high degree of craftsmanship and reli-ability that have made Yamaha a leader in these fields.This manual will give you an understanding of the operation, inspection, and basic maintenance of this motorcycle. If youhave any questions concerning the operation or maintenance of your motorcycle, please consult a Yamaha dealer.The design and manufacture of this Yamaha motorcycle fully comply with the emissions standards for clean air applicableat the date of manufacture. Yamaha has met these standards without reducing the performance or economy of operation ofthe motorcycle. To maintain these high standards, it is important that you and your Yamaha dealer pay close attention to therecommended maintenance schedules and operating instructions contained within this manual.Yamaha continually seeks advancements in product design and quality. Therefore, while this manual contains the most cur-rent product information available at the time of printing, there may be minor discrepancies between your motorcycle and thismanual. If there is any question concerning this manual, please consult a Yamaha dealer.
WARNING
EWA14461
Please read this manual, the “TIPS AND PRACTICE GUIDE FOR THE OFF HIGHWAY MOTORCYCLIST” and the“PARENTS, YOUNGSTERS AND OFF-HIGHWAY MOTORCYCLES” booklets carefully and completely before oper-ating or allowing your child to operate this motorcycle. Do not attempt to operate this motorcycle until you haveattained adequate knowledge of its controls and operating features and until you have been trained in safe andproper riding techniques. Regular inspections and careful maintenance, along with good riding skills, will ensure
that you safely enjoy the capabilities and the reliability of this motorcycle.
WARNING
EWA14351
This motorcycle is designed and manufactured for off-road use only. It is illegal to operate this motorcycle on anypublic street, road or highway. Such use is prohibited by law. This motorcycle complies with almost all stateoff-highway noise level and spark arrester laws and regulations. Please check your local riding laws and regulations
before operating this motorcycle.
INTRODUCTION
AN IMPORTANT SAFETY MESSAGE:
�
Read this manual, the “PARENTS, YOUNGSTERS AND OFF-HIGHWAY MOTORCYCLES” booklet, and the “TIPSAND PRACTICE GUIDE FOR THE OFF HIGHWAY MOTORCYCLIST” booklet carefully and completely before oper-ating this motorcycle. Make sure you understand all instructions.
�
Pay close attention to the warning and notice labels on the motorcycle.
�
Never operate a motorcycle without proper training or instruction.
�
Weight of the rider should not exceed 25 kg (55 lb).
AN IMPORTANT NOTE TO PARENTS:
This motorcycle is not a toy. Before you let your child ride this motorcycle, you should understand the instructions and warn-ings in this Owner’s Manual. Then be sure your child understands and will follow them. Also read the “PARENTS, YOUNG-STERS AND OFF-HIGHWAY MOTORCYCLES” and the “TIPS AND PRACTICE GUIDE FOR THE OFF HIGHWAYMOTORCYCLIST” booklets supplied with this motorcycle when new or available from your Yamaha dealer. Children differin skills, physical abilities, and judgment. Some children may not be able to operate a motorcycle safely. Parents should su-pervise their child’s use of the motorcycle at all times. Parents should permit continued use only if they determine that thechild has the ability to operate the motorcycle safely.Your motorcycle was delivered with an adjustable speed limiter and power reduction plate. Yamaha recommends that allbeginners start off with the speed limiter adjusting screw turned in and the power reduction plate installed in the exhaust man-ifold to limit the power available while they learn. The limiter screw may be gradually turned out to increase maximum speedas the beginner becomes more familiar with operating the motorcycle. Parents should decide when to adjust the motorcyclefor more power as their youngster’s riding skills improve. Once the rider can operate with skill at the top speed permitted byadjusting the speed limiter alone, the power reduction plate can be removed. Since removal of this plate will result in a sig-nificant increase in power, turn the speed limiter back in again; adjust it out in stages as you did before.
Motorcycles are single track vehicles. Their safe use and operation are dependent upon the use of proper ridingtechniques as well as the expertise of the operator. Every operator should know the following requirements beforeriding this motorcycle.
He or she should:
�
Obtain thorough instructions from a competent source on all aspects of motorcycle operation.
�
Observe the warnings and maintenance requirements in this Owner’s Manual.
INTRODUCTION
�
Obtain qualified training in safe and proper riding techniques.
�
Obtain professional technical service as indicated in this Owner’s Manual and/or when made necessary by mechanicalconditions.
IMPORTANT MANUAL INFORMATION
EAU10132
Particularly important information is distinguished in this manual by the following notations:
This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death.
A WARNING indicates a hazardous situation which, if not avoided, could result in death or serious injury.
A NOTICE indicates special precautions that must be taken to avoid damage to the vehicle or other property.
A TIP provides key information to make procedures easier or clearer.
WARNING
NOTICE
TIP
IMPORTANT MANUAL INFORMATION
EAU10193
PW50(Y)OWNER’S MANUAL
©2008 by Yamaha Motor Corporation, U.S.A.1st edition, March 2008
All rights reserved.Any reprinting or unauthorized use without the written permission of Yamaha Motor Corporation, U.S.A.
is expressly prohibited.Printed in Japan.
P/N LIT-11626-22-24
TABLE OF CONTENTS
LOCATION OF IMPORTANT LABELS
..............................................1-1
SAFETY INFORMATION
...................2-1
DESCRIPTION
...................................3-1Left view ...........................................3-1Right view .........................................3-2Controls and instruments..................3-3
INSTRUMENT AND CONTROL FUNCTIONS
........................................4-1Handlebar switch .............................4-1Speed limiter and power reduction
plate .............................................4-1Front brake lever .............................4-2Rear brake lever ..............................4-3Fuel tank cap ...................................4-3Fuel ..................................................4-3Fuel tank breather hose ...................4-52-stroke engine oil ...........................4-5Fuel cock .........................................4-5Starter (choke) lever “
1
” .................4-6Kickstarter ........................................4-6Seat .................................................4-7
FOR YOUR SAFETY – PRE-OPERATION CHECKS
...............5-1Pre-operation check list ...................5-2
OPERATION AND IMPORTANT RIDING POINTS
.................................. 6-1Starting and warming up a cold
engine .......................................... 6-1Starting a warm engine ................... 6-1Starting off ....................................... 6-2Acceleration and deceleration ......... 6-2Braking ............................................ 6-2Engine break-in ............................... 6-3Parking ............................................ 6-4
PERIODIC MAINTENANCE AND ADJUSTMENT
.................................... 7-1Owner’s tool kit ................................ 7-2Periodic maintenance chart for the
emission control system .............. 7-3General maintenance and lubrication
chart ............................................. 7-4Checking the spark plug .................. 7-6Removing the power reduction
plate ............................................. 7-7Transmission oil .............................. 7-8Middle and final gear cases ............ 7-9Cleaning the air filter element ......... 7-9Cleaning the spark arrester ........... 7-10Adjusting the carburetor ................ 7-11Adjusting the engine idling
speed ......................................... 7-11Checking the throttle cable free
play ............................................ 7-12Tires .............................................. 7-12
Panel wheels ................................. 7-14Adjusting the front and rear brake
lever free play ............................ 7-15Checking the front and rear brake
shoes ......................................... 7-16Checking and lubricating the
cables ........................................ 7-16Checking and lubricating the throttle
grip and cable ............................ 7-17Adjusting the Autolube pump ........ 7-17Lubricating the front and rear brake
levers ......................................... 7-17Checking and lubricating the
centerstand ................................ 7-18Checking the front fork .................. 7-18Checking the steering ................... 7-19Checking the wheel bearings ........ 7-19Front wheel ................................... 7-19Rear wheel .................................... 7-21Troubleshooting ............................ 7-24Troubleshooting chart ................... 7-25
MOTORCYCLE CARE AND STORAGE
........................................... 8-1Matte color caution .......................... 8-1Care ................................................ 8-1Storage ........................................... 8-3
SPECIFICATIONS
............................. 9-1
TABLE OF CONTENTS
CONSUMER INFORMATION
............10-1Identification numbers ...................10-1Motorcycle noise regulation ...........10-2YAMAHA MOTOR CORPORATION,
U.S.A. OFF-ROAD MOTORCYCLE LIMITED WARRANTY ...............10-3
YAMAHA EXTENDED SERVICE (Y.E.S.) ......................................10-5
1-1
1
LOCATION OF IMPORTANT LABELS
EAU41371
Read and understand all of the labels on your vehicle. They contain important information for safe and proper operation ofyour vehicle. Never remove any labels from your vehicle. If a label becomes difficult to read or comes off, a replacement labelis available from your Yamaha dealer.
2
1
LOCATION OF IMPORTANT LABELS
1-2
1
2
3
4
5
6
7
8
9
1
WARNINGBEFORE YOU OPERATE THIS VEHICLE, READ THE OWNER’SMANUAL AND ALL LABELS.NEVER CARRY A PASSENGER. You increase your risk of losingcontrol if you carry a passenger.NEVER OPERATE THIS VEHICLE ON PUBLIC ROADS. You cancollide with another vehicle if you operate this vehicle on a public road.ALWAYS WEAR AN APPROVED MOTORCYCLE HELMET,eye protection, and protective clothing.
3PT-2118K-A0
follows.FRONT :
:REAR3RV-21668-A0
Cold tire normal pressure should be set as
100 kPa,{1.00 kgf/cm2}, 15 psi100 kPa,{1.00 kgf/cm2}, 15 psi
2
2-1
1
2
SAFETY INFORMATION
EAU40933
Be a Responsible Owner
As the vehicle’s owner, you are respon-sible for the safe and proper operationof your motorcycle.Motorcycles are single-track vehicles.Their safe use and operation are de-pendent upon the use of proper ridingtechniques as well as the expertise ofthe operator. Every operator shouldknow the following requirements beforeriding this motorcycle.He or she should:
�
Obtain thorough instructions froma competent source on all aspectsof motorcycle operation.
�
Observe the warnings and mainte-nance requirements in this Own-er’s Manual.
�
Obtain qualified training in safeand proper riding techniques.
�
Obtain professional technical ser-vice as indicated in this Owner’sManual and/or when made neces-sary by mechanical conditions.
Safe Riding
Perform the pre-operation checks each
time you use the vehicle to make sure itis in safe operating condition. Failure toinspect or maintain the vehicle properlyincreases the possibility of an accidentor equipment damage. See page 5-1for a list of pre-operation checks.
�
This motorcycle is designed foroff-road use only, therefore, it is il-legal to operate it on public streets,roads, or highways, even a dirt orgravel one. Off-road use on publiclands may be illegal. Please checklocal regulations before riding.
�
This motorcycle is designed to car-ry the operator only. No passen-gers.
�
The failure of motorists to detectand recognize motorcycles in traf-fic is the predominating cause ofautomobile/motorcycle accidents.Many accidents have been causedby an automobile driver who didnot see the motorcycle. Makingyourself conspicuous appears tobe very effective in reducing thechance of this type of accident.
Therefore:
�
Wear a brightly colored jacket.
�
Use extra caution when you areapproaching and passingthrough intersections, since in-tersections are the most likelyplaces for motorcycle accidentsto occur.
�
Ride where other motorists cansee you. Avoid riding in anothermotorist’s blind spot.
�
Many accidents involve inexperi-enced operators.
�
Make sure that you are qualifiedand that you only lend your mo-torcycle to other qualified opera-tors.
�
Know your skills and limits.Staying within your limits mayhelp you to avoid an accident.
�
We recommend that you prac-tice riding your motorcycle untilyou have become thoroughly fa-miliar with the motorcycle and allof its controls.
�
Many accidents have been causedby error of the motorcycle opera-tor. A typical error made by the op-erator is veering wide on a turndue to excessive speed or under-
SAFETY INFORMATION
2-2
1
2
cornering (insufficient lean anglefor the speed). Never travel fasterthan warranted by conditions.
�
Ride cautiously in unfamiliar ar-eas. You may encounter hiddenobstacles that could cause an ac-cident.
�
The posture of the operator is im-portant for proper control. The op-erator should keep both hands onthe handlebar and both feet on theoperator footrests during operationto maintain control of the motorcy-cle.
�
Never ride under the influence ofalcohol or other drugs.
Protective apparel
The majority of fatalities from motorcy-cle accidents are the result of head in-juries. The use of a safety helmet is thesingle most critical factor in the preven-tion or reduction of head injuries.
�
Always wear an approved helmet.
�
Wear a face shield or goggles.Wind in your unprotected eyescould contribute to an impairmentof vision that could delay seeing a
hazard.
�
The use of a jacket, heavy boots,trousers, gloves, etc., is effective inpreventing or reducing abrasionsor lacerations.
�
Never wear loose-fitting clothes,otherwise they could catch on thecontrol levers, footrests, or wheelsand cause injury or an accident.
�
Always wear protective clothingthat covers your legs, ankles, andfeet. The engine or exhaust sys-tem become very hot during or af-ter operation and can cause burns.
Avoid Carbon Monoxide Poisoning
All engine exhaust contains carbonmonoxide, a deadly gas. Breathing car-bon monoxide can cause headaches,dizziness, drowsiness, nausea, confu-sion, and eventually death.Carbon Monoxide is a colorless, odor-less, tasteless gas which may bepresent even if you do not see or smellany engine exhaust. Deadly levels ofcarbon monoxide can collect rapidlyand you can quickly be overcome andunable to save yourself. Also, deadly
levels of carbon monoxide can lingerfor hours or days in enclosed or poorlyventilated areas. If you experience anysymptoms of carbon monoxide poison-ing, leave the area immediately, getfresh air, and SEEK MEDICAL TREAT-MENT.
�
Do not run engine indoors. Even ifyou try to ventilate engine exhaustwith fans or open windows anddoors, carbon monoxide can rap-idly reach dangerous levels.
�
Do not run engine in poorly venti-lated or partially enclosed areassuch as barns, garages, or car-ports.
�
Do not run engine outdoors whereengine exhaust can be drawn intoa building through openings suchas windows and doors.
Loading
Adding accessories to your motorcyclecan adversely affect stability and han-dling if the weight distribution of the mo-torcycle is changed. To avoid thepossibility of an accident, use extremecaution when adding accessories to
SAFETY INFORMATION
2-3
1
2
your motorcycle. Use extra care whenriding a motorcycle that has added ac-cessories. Here are some generalguidelines to follow if adding accesso-ries to your motorcycle:
Operation of an overloaded vehiclecould cause an accident.
�
The weight of the operator mustnot exceed 25 kg (55 lb).
�
Accessory weight should be keptas low and close to the motorcycleas possible. Securely pack yourheaviest items as close to the cen-ter of the vehicle as possible andmake sure to distribute the weightas evenly as possible on bothsides of the motorcycle to mini-mize imbalance or instability.
�
Shifting weights can create a sud-den imbalance. Make sure that ac-cessories are securely attached tothe motorcycle before riding.Check accessory mounts fre-quently.
�
Properly adjust the suspensionfor your load, and check the con-dition and pressure of your tires.
�
Never attach any large or heavyitems to the handlebar, frontfork, or front fender.
Genuine Yamaha Accessories
Choosing accessories for your vehicleis an important decision. GenuineYamaha accessories, which are avail-able only from a Yamaha dealer, havebeen designed, tested, and approvedby Yamaha for use on your vehicle.Many companies with no connection toYamaha manufacture parts and acces-sories or offer other modifications forYamaha vehicles. Yamaha is not in aposition to test the products that theseaftermarket companies produce.Therefore, Yamaha can neither en-dorse nor recommend the use of ac-cessories not sold by Yamaha ormodifications not specifically recom-mended by Yamaha, even if sold andinstalled by a Yamaha dealer.
Aftermarket Parts, Accessories, and Modifications
While you may find aftermarket prod-ucts similar in design and quality to
genuine Yamaha accessories, recog-nize that some aftermarket accessoriesor modifications are not suitable be-cause of potential safety hazards to youor others. Installing aftermarket prod-ucts or having other modifications per-formed to your vehicle that change anyof the vehicle’s design or operationcharacteristics can put you and othersat greater risk of serious injury or death.You are responsible for injuries relatedto changes in the vehicle.Keep the following guidelines in mind,as well as those provided under “Load-ing” when mounting accessories.
�
Never install accessories thatwould impair the performance ofyour motorcycle. Carefully inspectthe accessory before using it tomake sure that it does not in anyway reduce ground clearance orcornering clearance, limit suspen-sion travel, steering travel or con-trol operation.
�
Accessories fitted to the handle-bar or the front fork area cancreate instability due to improperweight distribution. If accesso-
SAFETY INFORMATION
2-4
1
2
ries are added to the handlebaror front fork area, they must beas lightweight as possible andshould be kept to a minimum.
�
Bulky or large accessories mayseriously affect the stability ofthe motorcycle. Wind may at-tempt to lift the motorcycle, orthe motorcycle may become un-stable in cross winds.
�
Certain accessories can dis-place the operator from his orher normal riding position. Thisimproper position limits the free-dom of movement of the opera-tor and may limit control ability,therefore, such accessories arenot recommended.
�
Use caution when adding electri-cal accessories. If electrical acces-sories exceed the capacity of themotorcycle’s electrical system, anelectric failure could result, whichcould cause a dangerous loss oflights or engine power.
Aftermarket Tires and Rims
The tires and rims that came with your
motorcycle were designed to match theperformance capabilities and to providethe best combination of handling, brak-ing, and comfort. Other tires, rims, siz-es, and combinations may not beappropriate. Refer to page 7-12 for tirespecifications and more information onreplacing your tires.
3-1
1
2
3
4
5
6
7
8
9
DESCRIPTION
EAU10410
Left view
1 2 3
45
1. Fuel cock (page 4-5)2. Throttle stop screw (page 7-11)3. Air filter element (page 7-9)4. Kickstarter (page 4-6)5. Centerstand (page 7-18)
DESCRIPTION
3-2
2
3
4
5
6
7
8
9
EAU10420
Right view
31 2 4
1. Spark arrester (page 7-10)2. Seat (page 4-7)3. Transmission oil filler cap (page 7-8)4. 2-stroke engine oil tank (page 4-5)
DESCRIPTION
3-3
1
2
3
4
5
6
7
8
9
EAU10430
Controls and instruments
1 2
7
3 4 5
6
1. Rear brake lever (page 4-3)2. Starter (choke) lever (page 4-6)3. 2-stroke engine oil tank cap (page 4-5)4. Right handlebar switch (page 4-1)5. Front brake lever (page 4-2)6. Throttle grip (page 7-12)7. Fuel tank cap (page 4-3)
4-1
2
3
4
5
6
7
8
9
INSTRUMENT AND CONTROL FUNCTIONS
EAU40660
Handlebar switch
EAU40674
Engine stop switch “OFF/RUN/START”
Set this switch to “START” before start-ing the engine. Set this switch to “RUN”after warming up the engine or beforestarting off. Set this switch to “OFF” tostop the engine.
TIP
�
The engine cannot be started withthis switch set to the “RUN” posi-tion.
�
The engine speed is limited whilethis switch is set to the “START”position, therefore the motorcycle
cannot be ridden in that switch po-
sition.
EAU41041
Speed limiter and power reduction plate
Your motorcycle was delivered with anadjustable speed limiter and a powerreduction plate. The speed limiterkeeps the throttle from fully opening,even when the throttle grip is turned tothe maximum. The power reductionplate is installed in the exhaust mani-fold to limit the amount of power avail-able while they learn.
Speed limiter
1. Loosen the locknut.2. To increase the maximum engine
power available and the maximumspeed of the motorcycle, turn theadjusting screw in direction (a). Todecrease the maximum enginepower available and the maximumspeed of the motorcycle, turn theadjusting screw in direction (b).
1. Engine stop switch “OFF/RUN/START”
1
INSTRUMENT AND CONTROL FUNCTIONS
4-2
1
2
3
4
5
6
7
8
9
3. Tighten the locknut.
TIP
The adjusting range of the speed limiterscrew is from the fully turned-in positionto 7 mm (0.28 in) turned out. When the
screw is turned out to 7 mm (0.28 in),the throttle grip can only be opened ap-proximately halfway. If more power isrequired, please consult a Yamaha
dealer.
WARNING
EWA14630
Improper adjustment of the speedlimiter could cause improper throttleoperation. You could lose control,have an accident or be injured. Donot turn the adjusting screw outmore than 7 mm (0.28 in) before con-sulting a Yamaha dealer. Alwaysmake sure the throttle cable freeplay is adjusted to 1.5–3.5 mm
(0.06–0.14 in). (See page 7-12.)
Power reduction plate
Once the rider can operate with skill atthe top speed permitted by adjustingthe speed limiter alone, the power re-duction plate can be removed. (Seepage 7-7.)
EAU12900
Front brake lever
The front brake lever is located on theright handlebar grip. To apply the frontbrake, pull this lever toward the handle-bar grip.
1. Locknut2. Adjusting screw
1. No more than 7 mm (0.28 in)
1
(a)
(b)
2
1
1. Front brake lever
1
INSTRUMENT AND CONTROL FUNCTIONS
4-3
2
3
4
5
6
7
8
9
EAU12950
Rear brake lever
The rear brake lever is located on theleft handlebar grip. To apply the rearbrake, pull this lever toward the handle-bar grip.
EAU13182
Fuel tank cap
To remove the fuel tank cap, turn itcounterclockwise, and then pull it off.To install the fuel tank cap, insert it intothe tank opening, and then turn it clock-wise.
WARNING
EWA11091
Make sure that the fuel tank cap isproperly closed after filling fuel.
Leaking fuel is a fire hazard.
EAU13221
Fuel
Make sure there is sufficient gasoline inthe tank.
WARNING
EWA10881
Gasoline and gasoline vapors areextremely flammable. To avoid firesand explosions and to reduce therisk of injury when refueling, follow
these instructions.
1. Before refueling, turn off the en-gine and be sure that no one is sit-ting on the vehicle. Never refuelwhile smoking, or while in the vi-cinity of sparks, open flames, orother sources of ignition such asthe pilot lights of water heaters andclothes dryers.
2. Do not overfill the fuel tank. Whenrefueling, be sure to insert thepump nozzle into the fuel tank fillerhole. Stop filling when the fuelreaches the bottom of the fillertube. Because fuel expands whenit heats up, heat from the engine orthe sun can cause fuel to spill outof the fuel tank.
1. Rear brake lever
1
1. Fuel tank cap
1
INSTRUMENT AND CONTROL FUNCTIONS
4-4
1
2
3
4
5
6
7
8
9
3. Wipe up any spilled fuel immedi-ately.
NOTICE:
Immediately wipeoff spilled fuel with a clean, dry,soft cloth, since fuel may deteri-orate painted surfaces or plasticparts.
[ECA10071]
4. Be sure to securely close the fuel
tank cap.
WARNING
EWA15151
Gasoline is poisonous and cancause injury or death. Handle gaso-line with care. Never siphon gaso-line by mouth. If you should swallowsome gasoline or inhale a lot of gas-oline vapor, or get some gasoline in
your eyes, see your doctor immedi-ately. If gasoline spills on your skin,wash with soap and water. If gaso-line spills on your clothing, change
your clothes.
EAU40681
Your Yamaha engine has been de-signed to use regular unleaded gaso-line with a pump octane number[(R+M)/2] of 86 or higher, or a researchoctane number of 91 or higher. Ifknocking (or pinging) occurs, use agasoline of a different brand or premi-um unleaded fuel. Use of unleaded fuelwill extend spark plug life and reducemaintenance costs.
Gasohol
There are two types of gasohol: gaso-hol containing ethanol and that contain-ing methanol. Gasohol containingethanol can be used if the ethanol con-
tent does not exceed 10% (E10). Gas-ohol containing methanol is notrecommended by Yamaha because itcan cause damage to the fuel systemor vehicle performance problems.
1. Fuel tank filler tube2. Fuel level
21
Recommended fuel:
UNLEADED GASOLINE ONLY
Fuel tank capacity:
2.0 L (0.53 US gal, 0.44 Imp.gal)
INSTRUMENT AND CONTROL FUNCTIONS
4-5
2
3
4
5
6
7
8
9
EAU13412
Fuel tank breather hose
Before operating the motorcycle:
�
Check the fuel tank breather hoseconnection.
�
Check the fuel tank breather hosefor cracks or damage, and replaceit if damaged.
�
Make sure that the fuel tankbreather hose is not blocked, andclean it if necessary.
EAU13452
2-stroke engine oil
Make sure that there is sufficient2-stroke engine oil in the oil tank. Addthe recommended 2-stroke engine oilas necessary.
TIP
Make sure that the 2-stroke engine oil
tank cap is properly installed.
EAU40701
Fuel cock
The fuel cock supplies fuel from thetank to the carburetor while filtering it al-so.The fuel cock has two positions:
S (stop)
With the lever in this position, fuel willnot flow. Always return the lever to thisposition when the engine is not running.
1. Fuel tank breather hose
1
1. 2-stroke engine oil tank cap2. Minimum level mark
Recommended oil:
See page 9-1.
Oil quantity:
0.30 L (0.32 US qt, 0.26 Imp.qt)
2
1
1. Arrow mark pointing to “S” (stop)
1
INSTRUMENT AND CONTROL FUNCTIONS
4-6
1
2
3
4
5
6
7
8
9
O (on)
With the lever in this position, fuel flowsto the carburetor. Normal riding is donewith the lever in this position.
EAU13590
Starter (choke) lever “ ”
Starting a cold engine requires a richerair-fuel mixture, which is supplied bythe starter (choke).Move the lever in direction (a) to turn onthe starter (choke).Move the lever in direction (b) to turn offthe starter (choke).
EAU13680
Kickstarter
To start the engine, fold out the kick-starter lever, move it down lightly withyour foot until the gears engage, andthen push it down smoothly but force-fully.
1. Arrow mark pointing to “O” (on)
1
1. Starter (choke) lever “ ”
1
(a)
(b)
1. Kickstarter
1
INSTRUMENT AND CONTROL FUNCTIONS
4-7
2
3
4
5
6
7
8
9
EAU40920
Seat
To remove the seat
1. Remove the mudguard by remov-ing the bolts and washers.
2. Pull the seat off.
To install the seat
1. Insert the projection on the front ofthe seat into the seat holder asshown.
2. Place the seat in the original posi-tion.
3. Install the mudguard by installingthe washers and bolts.
TIP
Make sure that the seat is properly se-
cured before riding.
1. Bolt2. Mudguard
12
1. Seat holder2. Projection
1 2
5-1
1
2
3
4
5
6
7
8
9
FOR YOUR SAFETY – PRE-OPERATION CHECKS
EAU15595
Inspect your vehicle each time you use it to make sure the vehicle is in safe operating condition. Always follow the inspectionand maintenance procedures and schedules described in the Owner’s Manual.
WARNING
EWA11151
Failure to inspect or maintain the vehicle properly increases the possibility of an accident or equipment damage.Do not operate the vehicle if you find any problem. If a problem cannot be corrected by the procedures provided in
this manual, have the vehicle inspected by a Yamaha dealer.
Before using this vehicle, check the following points:
FOR YOUR SAFETY – PRE-OPERATION CHECKS
5-2
2
3
4
5
6
7
8
9
EAU15605
Pre-operation check list
ITEM CHECKS PAGE
Fuel
�
Check fuel level in fuel tank.
�
Refuel if necessary.
�
Check fuel line for leakage.4-3
2-stroke engine oil
�
Check oil level in oil tank.
�
If necessary, add recommended oil to specified level.
�
Check vehicle for oil leakage.4-5
Transmission oil
�
Check oil level in transmission case.
�
If necessary, add recommended oil to specified level.7-8
Middle and final gear cases
�
Check vehicle for grease leakage. 7-9
Front brake
�
Check operation.
�
Lubricate cable if necessary.
�
Check lever free play.
�
Adjust if necessary.
7-15, 7-16
Rear brake
�
Check operation.
�
Lubricate cable if necessary.
�
Check lever free play.
�
Adjust if necessary.
7-15, 7-16
Throttle grip
�
Make sure that operation is smooth.
�
Check cable free play.
�
If necessary, have Yamaha dealer adjust cable free play and lubricate cable and grip housing.
7-12, 7-17
Control cables
�
Make sure that operation is smooth.
�
Lubricate if necessary.7-16
Wheels and tires
�
Check for damage.
�
Check tire condition and tread depth.
�
Check air pressure.
�
Correct if necessary.
7-12, 7-14
Brake levers
�
Make sure that operation is smooth.
�
Lubricate lever pivoting points if necessary.7-17
FOR YOUR SAFETY – PRE-OPERATION CHECKS
5-3
1
2
3
4
5
6
7
8
9
Centerstand
�
Make sure that operation is smooth.
�
Lubricate pivot if necessary.7-18
Chassis fasteners
�
Make sure that all nuts, bolts and screws are properly tightened.
�
Tighten if necessary.—
Engine stop switch
�
Check operation. 4-1
ITEM CHECKS PAGE
6-1
2
3
4
5
6
7
8
9
OPERATION AND IMPORTANT RIDING POINTS
EAU40771
WARNING
EWA14531
�
This model is designed foroff-road use only. Become thor-oughly familiar with all operat-ing controls and their functionsbefore riding. Consult a Yamahadealer regarding any control orfunction that you do not thor-oughly understand.
�
Never start the engine or oper-ate it in a closed area for anylength of time. Exhaust fumesare poisonous, and inhalingthem can cause loss of con-sciousness and death within ashort time. Always make surethat there is adequate ventila-
tion.
EAU40886
Starting and warming up a cold engine
1. Turn the fuel cock lever to “O” (on).2. Set the engine stop switch to
“START”.3. Turn the starter (choke) on and
completely close the throttle. (Seepage 4-6.)
4. While applying the front or rearbrake, start the engine by pushingthe kickstarter lever down.
5. After starting the engine, move thestarter (choke) back halfway.
NOTICE:
For maximum enginelife, always warm the engine upbefore starting off. Never accel-erate hard when the engine iscold!
[ECA11131]
6. When the engine is warm, turn the
starter (choke) off and set the en-gine stop switch to “RUN”.
TIP
The engine is warm when it respondsnormally to the throttle with the starter
(choke) turned off.
EAU16660
Starting a warm engine
Follow the same procedure as for start-ing a cold engine with the exceptionthat the starter (choke) is not requiredwhen the engine is warm. Instead, startthe engine with the throttle slightlyopen.
TIP
If the engine does not start after sever-al kicks, try again with the throttle 1/4
to 1/2 open.
OPERATION AND IMPORTANT RIDING POINTS
6-2
1
2
3
4
5
6
7
8
9
EAU41001
Starting off TIP
Before starting off, allow the engine to
warm up.
1. While applying the rear brake le-ver, push the motorcycle off thecenterstand.
2. Completely close the throttle.3. Set the engine stop switch to
“RUN”.4. Check for oncoming off-road vehi-
cles, and then slowly turn the throt-tle grip in order to take off.
EAU16780
Acceleration and deceleration
The speed can be adjusted by openingand closing the throttle. To increase thespeed, turn the throttle grip in direction(a). To reduce the speed, turn the throt-tle grip in direction (b).
EAU41012
Braking
WARNING
EWA14571
�
Avoid braking hard or suddenly(especially when leaning over toone side), otherwise the motor-cycle may skid or overturn.
�
Keep in mind that braking onwet surfaces is much more diffi-cult.
�
Ride slowly down a hill, as brak-ing downhill can be very diffi-
cult.
1. Close the throttle completely.2. Apply both front and rear brakes
simultaneously while gradually in-creasing the pressure.
(a)
(b)
OPERATION AND IMPORTANT RIDING POINTS
6-3
2
3
4
5
6
7
8
9
Front
Rear
EAU42030
Engine break-in
There is never a more important periodin the life of your engine than the first 5hours of riding. It is also important to ac-custom the rider to the motorcycle dur-ing this time. Please read the followinginformation carefully.Since the engine is brand new, do notput an excessive load on it for the first 5hours of operation. The various parts inthe engine wear and polish themselvesto the correct operating clearances.During this period, prolonged full-throt-tle operation or any condition that mightresult in engine overheating must beavoided. However, momentaryfull-throttle operation under load (i.e.,two to three seconds maximum) doesnot harm the engine. Each full-throttleacceleration should be followed with asubstantial rest period for the engine.To allow the engine to cool down fromthe temporary buildup of heat, cruise ata lower engine speed.After the first 5 hours of operation, thor-oughly check the motorcycle for looseparts, oil leakage and any other prob-lems. Be sure to inspect and make ad-
justments thoroughly, especiallycables. In addition, check all fittings andfasteners for looseness, and tighten ifnecessary.
NOTICE
ECA10270
If any engine trouble should occurduring the engine break-in period,immediately have a Yamaha dealer
check the vehicle.
OPERATION AND IMPORTANT RIDING POINTS
6-4
1
2
3
4
5
6
7
8
9
EAU40722
Parking
When parking, stop the engine, andthen turn the fuel cock lever to “S”(stop).
WARNING
EWA10311
�
Since the engine and exhaustsystem can become very hot,park in a place where pedestri-ans or children are not likely totouch them and be burned.
�
Do not park on a slope or on softground, otherwise the vehiclemay overturn, increasing therisk of a fuel leak and fire.
�
Do not park near grass or otherflammable materials which
might catch fire.
7-1
2
3
4
5
6
7
8
9
PERIODIC MAINTENANCE AND ADJUSTMENT
EAU41951
Periodic inspection, adjustment, and lu-brication will keep your vehicle in thesafest and most efficient condition pos-sible. Safety is an obligation of the vehi-cle owner/operator. The most importantpoints of vehicle inspection, adjust-ment, and lubrication are explained onthe following pages.
WARNING
EWA10321
Failure to properly maintain the ve-hicle or performing maintenance ac-tivities incorrectly may increaseyour risk of injury or death duringservice or while using the vehicle. Ifyou are not familiar with vehicle ser-vice, have a Yamaha dealer perform
service.
WARNING
EWA15121
Turn off the engine when performingmaintenance unless otherwisespecified.
�
A running engine has movingparts that can catch on bodyparts or clothing and electrical
parts that can cause shocks orfires.
�
Running the engine while ser-vicing can lead to eye injury,burns, fire, or carbon monoxidepoisoning – possibly leading todeath. See page 2-1 for more in-formation about carbon monox-
ide.
EAU17302
Emission controls not only function toensure cleaner air, but are also vital toproper engine operation and maximumperformance. In the following periodicmaintenance charts, the services relat-ed to emissions control are groupedseparately. These services requirespecialized data, knowledge, andequipment. Maintenance, replacement,or repair of the emission control devic-es and systems may be performed byany repair establishment or individualthat is certified (if applicable). Yamahadealers are trained and equipped toperform these particular services.
PERIODIC MAINTENANCE AND ADJUSTMENT
7-2
1
2
3
4
5
6
7
8
9
EAU17311
Owner’s tool kit
The service information included in thismanual and the tools provided in theowner’s tool kit are intended to assistyou in the performance of preventivemaintenance and minor repairs. How-ever, additional tools such as a torquewrench may be necessary to performcertain maintenance work correctly.
TIP
If you do not have the tools or experi-ence required for a particular job, have
a Yamaha dealer perform it for you.
PERIODIC MAINTENANCE AND ADJUSTMENT
7-3
2
3
4
5
6
7
8
9
EAU41741
Periodic maintenance chart for the emission control system TIP
�
From 18 months, repeat the maintenance intervals starting from 6 months.
�
Items marked with an asterisk should be performed by a Yamaha dealer as they require special tools, data and technical
skills.
NO. ITEM CHECK OR MAINTENANCE JOB
INITIALTHEREAFTER
EVERY
1month
3 months
6 months
6 months
12 months
1 * Fuel lineCheck fuel hoses for cracks or damage.Replace if necessary.
2 Spark plugCheck condition.Adjust gap and clean.Replace if necessary.
3 Air filter elementClean with solvent.Replace if necessary.
4 * CarburetorCheck engine idling speed and starter operation.Adjust if necessary.Clean.
5 *Cylinder head and exhaust system
Check for leakage.Tighten if necessary.Decarbonize if necessary.
6 * Spark arrester Clean.
PERIODIC MAINTENANCE AND ADJUSTMENT
7-4
1
2
3
4
5
6
7
8
9
EAU41753
General maintenance and lubrication chart
NO. ITEM CHECK OR MAINTENANCE JOB
INITIALTHEREAFTER
EVERY
1month
3months
6months
6months
12 months
1 * Front brakeCheck operation.Adjust brake lever free play.Replace brake shoes. Whenever worn to the limit
2 * Rear brakeCheck operation.Adjust brake lever free play.Replace brake shoes. Whenever worn to the limit
3 * WheelsCheck runout and for damage.Replace if necessary.
4 * Tires
Check tread depth and for damage.Replace if necessary.Check air pressure.Correct if necessary.
5 * Wheel bearingsCheck bearings for smooth operation.Replace if necessary.
6 * Steering bearingsCheck bearing assemblies for looseness.Moderately repack with lithium-soap-based grease every 2 years.
7 *Middle and final gear cases
Check for grease leakage.Check gears for damage and wear.Lubricate gears with lithium-soap-based grease.
Every 2 years
8 * Chassis fastenersCheck all chassis fitting and fasteners.Correct if necessary.
9 * Autolube pumpCheck operation.Correct if necessary.Bleed.
PERIODIC MAINTENANCE AND ADJUSTMENT
7-5
2
3
4
5
6
7
8
9
TIP
The air filter needs more frequent service if you are riding in unusually wet or dusty areas.
10 * Transmission oilCheck for oil leakage.Correct if necessary.Change.
11 *Front and rear brake lever pivot
Apply lithium-soap-based grease lightly.
12 * Centerstand pivotCheck operation.Apply lithium-soap-based grease lightly.
13 *Shock absorber assemblies
Check operation and for oil leakage.Replace if necessary.
14 * Control cableApply Yamaha chain and cable lube or engine oil 10W-30 lightly.
15 *Throttle grip housing and cable
Check operation and free play.Apply Yamaha chain and cable lube or engine oil 10W-30 lightly.
NO. ITEM CHECK OR MAINTENANCE JOB
INITIALTHEREAFTER
EVERY
1month
3months
6months
6months
12 months
PERIODIC MAINTENANCE AND ADJUSTMENT
7-6
1
2
3
4
5
6
7
8
9
EAU19603
Checking the spark plug
The spark plug is an important enginecomponent, which is easy to check.Since heat and deposits will cause anyspark plug to slowly erode, the sparkplug should be removed and checkedin accordance with the periodic mainte-nance and lubrication chart. In addition,the condition of the spark plug can re-veal the condition of the engine.
To remove the spark plug
1. Remove the spark plug cap.
2. Remove the spark plug as shown,with the spark plug wrench includ-ed in the owner’s tool kit.
To check the spark plug
1. Check that the porcelain insulatoraround the center electrode of thespark plug is a medium-to-light tan(the ideal color when the vehicle isridden normally).
TIP
If the spark plug shows a distinctly dif-ferent color, the engine could be oper-ating improperly. Do not attempt todiagnose such problems yourself. In-stead, have a Yamaha dealer check
the vehicle.
2. Check the spark plug for electrodeerosion and excessive carbon or
other deposits, and replace it ifnecessary.
To install the spark plug
1. Measure the spark plug gap with awire thickness gauge and, if nec-essary, adjust the gap to specifica-tion.
2. Clean the surface of the spark pluggasket and its mating surface, and
1. Spark plug cap
1
1. Spark plug wrench
1
Specified spark plug:
NGK/BP4HSDENSO/W14FPL
1. Spark plug gap
Spark plug gap:
0.6–0.7 mm (0.024–0.028 in)
1
PERIODIC MAINTENANCE AND ADJUSTMENT
7-7
2
3
4
5
6
7
8
9
then wipe off any grime from thespark plug threads.
3. Install the spark plug with thespark plug wrench, and then tight-en it to the specified torque.
TIP
If a torque wrench is not available wheninstalling a spark plug, a good estimateof the correct torque is 1/4–1/2 turnpast finger tight. However, the sparkplug should be tightened to the speci-
fied torque as soon as possible.
4. Install the spark plug cap.
EAU41102
Removing the power reduction plate
To obtain full engine performance ca-pability, removing the power reductionplate is required.
1. Remove the exhaust manifold byremoving the bolts.
WARNING!Always let the exhaust systemcool prior to touching exhaustcomponents.
[EWA14581]
2. Remove the gasket.3. Remove the power reduction
plate.
TIP
Store the power reduction plate with theOwner’s Manual so that it is readilyavailable whenever you want to reduce
the engine power.
4. Install the exhaust manifold by in-stalling the bolts.
Tightening torque:
Spark plug:20 Nm (2.0 m·kgf, 14.5 ft·lbf)
1. Exhaust manifold bolt
1
1. Exhaust manifold2. Gasket3. Power reduction plate
Tightening torque:
Exhaust manifold bolt:8.5 Nm (0.9 m·kgf, 6.1 ft·lbf)
1
2
3
PERIODIC MAINTENANCE AND ADJUSTMENT
7-8
1
2
3
4
5
6
7
8
9
EAU40892
Transmission oil
The transmission oil must be checkedfor oil leakage before each ride. If anyleakage is found, have a Yamaha deal-er check and repair the motorcycle. Inaddition, the transmission oil must bechanged at the intervals specified in theperiodic maintenance and lubricationchart.
1. Place the motorcycle on the cen-terstand.
2. Place an oil pan under the trans-mission to collect the used oil.
3. Remove the oil filler cap and drainbolt to drain the oil from the trans-mission.
4. Install the transmission oil drainbolt, and then tighten it to the spec-ified torque.
5. Refill with the specified amount ofthe recommended transmissionoil, and then install and tighten theoil filler cap.
NOTICE
ECA10452
�
In order to prevent clutch slip-page (since the transmission oilalso lubricates the clutch), donot mix any chemical additives.Do not use oils with a dieselspecification of “CD” or oils of ahigher quality than specified. Inaddition, do not use oils labeled“ENERGY CONSERVING II” orhigher.
�
Make sure that no foreign mate-
rial enters the transmission.
6. Start the engine, and then let it idlefor several minutes while checkingthe transmission for oil leakage. Ifoil is leaking, immediately turn theengine off and check for the cause.
1. Transmission oil filler cap
1
1. Transmission oil drain bolt
Tightening torque:
Transmission oil drain bolt:14 Nm (1.4 m·kgf, 10.1 ft·lbf)
Recommended transmission oil:
See page 9-1.
Oil change quantity:
0.30 L (0.32 US qt, 0.26 Imp.qt)
1
PERIODIC MAINTENANCE AND ADJUSTMENT
7-9
2
3
4
5
6
7
8
9
EAU41711
Middle and final gear cases
The middle and final gear cases mustbe checked for grease leakage beforeeach ride. If any leakage is found, havea Yamaha dealer check and repair themotorcycle. In addition, have aYamaha dealer check and lubricate themiddle and final gears at the intervalsspecified in the periodic maintenanceand lubrication chart.
EAU40902
Cleaning the air filter element
The air filter element should be cleanedat the intervals specified in the periodicmaintenance and lubrication chart.Clean the air filter element more fre-quently if you are riding in unusuallywet or dusty areas.
1. Remove the seat. (See page 4-7.)2. Remove the air filter case cover by
removing the screw.
3. Pull the sponge material out, cleanit with solvent, and then squeezethe remaining solvent out.
4. Apply oil of the recommended typeto the entire surface of the spongematerial, and then squeeze the ex-cess oil out.
TIP
The sponge material should be wet but
1. Air filter case cover2. Screw
2
1
1. Sponge material
1
PERIODIC MAINTENANCE AND ADJUSTMENT
7-10
1
2
3
4
5
6
7
8
9
not dripping.
5. Insert the sponge material into theair filter case.
NOTICE:
Make surethat the sponge material is prop-erly seated in the air filter case.The engine should never be op-erated without the sponge mate-rial installed, otherwise thepiston(s) and/or cylinder(s) maybecome excessively worn.
[ECA15621]
6. Install the air filter case cover by in-
stalling the screw.7. Install the seat.
EAU41220
Cleaning the spark arrester
The spark arrester should be cleanedat the intervals specified in the periodicmaintenance and lubrication chart.
WARNING
EWA10980
�
Always let the exhaust systemcool prior to touching exhaustcomponents.
�
Do not start the engine when
cleaning the exhaust system.
TIP
Make sure to select a well-ventilatedarea free of combustible materials to
clean the spark arrester.
1. Remove the tailpipe by removingthe screw, and then pulling it out ofthe muffler.
2. Tap the tailpipe lightly, and thenuse a wire brush to remove anycarbon deposits from the spark ar-rester portion of the tailpipe and in-side of the tailpipe housing.
Recommended oil:
Yamaha foam air filter oil or other quality foam air filter oil
1. Tailpipe2. Screw3. Muffler
12
3
PERIODIC MAINTENANCE AND ADJUSTMENT
7-11
2
3
4
5
6
7
8
9
3. Insert the tailpipe into the muffler,and then install and tighten thescrew.
TIP
Make sure to align the screw hole when
inserting the tailpipe.
EAU39930
Adjusting the carburetor
The carburetor is an important part ofthe engine and requires very sophisti-cated adjustment. Therefore, most car-buretor adjustments should be left to aYamaha dealer, who has the neces-sary professional knowledge and expe-rience. The adjustment described in thefollowing section, however, may be ser-viced by the owner as part of routinemaintenance.
NOTICE
ECA10550
The carburetor has been set and ex-tensively tested at the Yamaha fac-tory. Changing these settingswithout sufficient technical knowl-edge may result in poor perfor-
mance of or damage to the engine.
EAU21362
Adjusting the engine idling speed
The engine idling speed must bechecked and, if necessary, adjusted asfollows at the intervals specified in theperiodic maintenance and lubricationchart.
TIP
A diagnostic tachometer is needed to
make this adjustment.
1. Attach the tachometer to the sparkplug lead.
2. Start the engine and warm it up forseveral minutes at 1000–2000 r/min while occasionally revving it to4000–5000 r/min.
TIP
The engine is warm when it quickly re-
sponds to the throttle.
3. Check the engine idling speedand, if necessary, adjust it to spec-ification by turning the throttle stopscrew. To increase the engineidling speed, turn the screw in di-rection (a). To decrease the en-gine idling speed, turn the screw in
1. Spark arrester
1
PERIODIC MAINTENANCE AND ADJUSTMENT
7-12
1
2
3
4
5
6
7
8
9
direction (b).
TIP
If the specified idling speed cannot beobtained as described above, have a
Yamaha dealer make the adjustment.
EAU21382
Checking the throttle cable free play
The throttle cable free play should mea-sure 1.5–3.5 mm (0.06–0.14 in) at thethrottle grip. Periodically check thethrottle cable free play and, if neces-sary, have a Yamaha dealer adjust it.
EAU40911
Tires
To maximize the performance, durabil-ity, and safe operation of your motorcy-cle, note the following points regardingthe specified tires.
Tire air pressure
The tire air pressure should be checkedand, if necessary, adjusted before eachride.
WARNING
EWA14381
Operation of this vehicle with im-proper tire pressure may cause se-vere injury or death from loss ofcontrol.
�
The tire air pressure must bechecked and adjusted on coldtires (i.e., when the temperatureof the tires equals the ambienttemperature).
�
The tire air pressure must be ad-justed in accordance with theweight of the rider, the ridingspeed, and the riding condi-
tions.
1. Throttle stop screw
Engine idling speed:
1650–1750 r/min
1
(a)(b)
1. Throttle cable free play
1
PERIODIC MAINTENANCE AND ADJUSTMENT
7-13
2
3
4
5
6
7
8
9
Tire inspection
The tires must be checked before eachride. If the center tread depth reachesthe specified limit, if the tire has a nail orglass fragments in it, or if the sidewall iscracked, have a Yamaha dealer re-place the tire immediately.
Tire information
This motorcycle is equipped with panelwheels and tube tires.
WARNING
EWA10461
The front and rear tires should be ofthe same make and design, other-wise the handling characteristics ofthe vehicle may be different, which
could lead to an accident.
After extensive tests, only the tires list-ed below have been approved for thismodel by Yamaha Motor Co., Ltd.
WARNING
EWA14390
�
Have a Yamaha dealer replaceexcessively worn tires. Operat-ing the motorcycle with exces-sively worn tires decreasesriding stability and can lead toloss of control.
�
The replacement of allwheel-and brake-related parts,including the tires, should beleft to a Yamaha dealer, who hasthe necessary professionalknowledge and experience.
�
It is not recommended to patcha punctured tube. If unavoid-able, however, patch the tube
Standard tire air pressure:
Front:100 kPa (1.00 kgf/cm
2
, 15 psi)Rear:
100 kPa (1.00 kgf/cm
2
, 15 psi)
1. Tire sidewall2. Tire tread depth
1
2
Minimum tire tread depth (front and rear):
4.0 mm (0.16 in)
Front tire:
Size:2.50-10 4PR
Manufacturer/model:BRIDGESTONE/KNOBBYIRC/KNOBBY
Rear tire:
Size:2.50-10 4PR
Manufacturer/model:BRIDGESTONE/KNOBBYIRC/KNOBBY
PERIODIC MAINTENANCE AND ADJUSTMENT
7-14
1
2
3
4
5
6
7
8
9
very carefully and replace it assoon as possible with a
high-quality product.
EAU40780
Panel wheels
WARNING
EWA10610
The wheels on this model are not de-signed for use with tubeless tires.Do not attempt to use tubeless tires
on this model.
To maximize the performance, durabil-ity, and safe operation of your motorcy-cle, note the following points regardingthe specified wheels.
�
The wheel rims should be checkedfor cracks, bends, warpage ordamage before each ride. If anydamage is found, have a Yamahadealer replace the wheel. Do notattempt even the smallest repair tothe wheel. A deformed or crackedwheel must be replaced.
�
The wheel should be balancedwhenever either the tire or wheelhas been changed or replaced. Anunbalanced wheel can result inpoor performance, adverse han-dling characteristics, and a short-ened tire life.
�
Ride conservatively after changing
a tire since the tire must seat itselfon the rim properly. Failure to al-low proper seating may cause tirefailure, which may result in dam-age to the motorcycle and injury tothe rider.
PERIODIC MAINTENANCE AND ADJUSTMENT
7-15
2
3
4
5
6
7
8
9
EAU22151
Adjusting the front and rear brake lever free play
Front
Rear
The front and rear brake lever free playshould be measured at the positions asshown.
Periodically check the front and rearbrake lever free play and, if necessary,adjust them as follows.To increase the brake lever free play,turn the adjusting nut at the brake shoeplate in direction (a). To decrease thebrake lever free play, turn the adjustingnut in direction (b).
Front
Rear
WARNING
EWA10650
If proper adjustment cannot be ob-tained as described, have a Yamaha
dealer make this adjustment.
1. Front brake lever free play
1. Rear brake lever free play
1
1
Front brake lever free play:
10.0–20.0 mm (0.39–0.79 in)
Rear brake lever free play:
10.0–20.0 mm (0.39–0.79 in)
1. Brake lever free play adjusting nut
1
(a)
(b)
1. Brake lever free play adjusting nut
1
(a)
(b)
PERIODIC MAINTENANCE AND ADJUSTMENT
7-16
1
2
3
4
5
6
7
8
9
EAU41052
Checking the front and rear brake shoes
The front and rear brake shoes must bechecked for wear at the intervals spec-ified in the periodic maintenance andlubrication chart.
TIP
The wheels must be removed to checkbrake shoe lining thickness.
�
To remove the front wheel: Seepage 7-19.
�
To remove the rear wheel: See
page 7-21.
Front
Rear
If the lining thickness of a brake shoe isless than 1.5 mm (0.06 in), have aYamaha dealer replace the brakeshoes as a set.
TIP
Be sure to measure the brake lining at
the thinnest portion.
EAU41842
Checking and lubricating the cables
The operation of all control cables andthe condition of the cables should bechecked before each ride, and the ca-bles and cable ends should be lubricat-ed if necessary. If a cable is damagedor does not move smoothly, have aYamaha dealer check or replace it.
WARNING! Damage to the outerhousing of cables may result in in-ternal rusting and cause interfer-ence with cable movement. Replacedamaged cables as soon as possi-ble to prevent unsafe condi-tions.
[EWA10711]
Recommended lubricant:
Yamaha Chain and Cable Lube or 4-stroke engine oil
PERIODIC MAINTENANCE AND ADJUSTMENT
7-17
2
3
4
5
6
7
8
9
EAU23111
Checking and lubricating the throttle grip and cable
The operation of the throttle grip shouldbe checked before each ride. In addi-tion, the cable should be lubricated atthe intervals specified in the periodicmaintenance chart.
EAU23120
Adjusting the Autolube pump
The Autolube pump is a vital and so-phisticated component of the engine,which must be adjusted by a Yamahadealer at the intervals specified in theperiodic maintenance and lubricationchart.
EAU43631
Lubricating the front and rear brake levers
The pivoting points of the front and rearbrake levers must be lubricated at theintervals specified in the periodic main-tenance and lubrication chart.
Recommended lubricant:
Lithium-soap-based grease
PERIODIC MAINTENANCE AND ADJUSTMENT
7-18
1
2
3
4
5
6
7
8
9
EAU23192
Checking and lubricating the centerstand
The operation of the centerstandshould be checked before each ride,and the pivots and metal-to-metal con-tact surfaces should be lubricated ifnecessary.
WARNING
EWA11301
If the centerstand does not move upand down smoothly, have a Yamahadealer check or repair it. Otherwise,the centerstand could contact theground and distract the operator, re-
sulting in a possible loss of control.
EAU42081
Checking the front fork
The condition and operation of the frontfork must be checked as follows at theintervals specified in the periodic main-tenance and lubrication chart.
To check the condition
Check the inner tubes for scratchesand damage.
To check the operation
1. Place the vehicle on a level sur-face and hold it in an upright posi-tion.
WARNING! To avoid injury,securely support the vehicle sothere is no danger of it fallingover.
[EWA10751]
2. While applying the front brake,
push down hard on the handlebarsseveral times to check if the frontfork compresses and reboundssmoothly.
NOTICE
ECA10590
If any damage is found or the frontfork does not operate smoothly,have a Yamaha dealer check or re-
pair it.
Recommended lubricant:
Lithium-soap-based grease
PERIODIC MAINTENANCE AND ADJUSTMENT
7-19
2
3
4
5
6
7
8
9
EAU45511
Checking the steering
Worn or loose steering bearings maycause danger. Therefore, the operationof the steering must be checked as fol-lows at the intervals specified in the pe-riodic maintenance and lubricationchart.
1. Place the vehicle on the center-stand.
WARNING! To avoid inju-ry, securely support the vehicleso there is no danger of it fallingover.
[EWA10751]
2. Hold the lower ends of the front
fork legs and try to move them for-ward and backward. If any freeplay can be felt, have a Yamahadealer check or repair the steering.
EAU23290
Checking the wheel bearings
The front and rear wheel bearings mustbe checked at the intervals specified inthe periodic maintenance and lubrica-tion chart. If there is play in the wheelhub or if the wheel does not turnsmoothly, have a Yamaha dealer checkthe wheel bearings.
EAU24360
Front wheel
EAU41022
To remove the front wheel
WARNING
EWA10821
To avoid injury, securely support thevehicle so there is no danger of it
falling over.
1. Place the motorcycle on the cen-terstand.
2. Disconnect the brake cable at thewheel by removing the brake leverfree play adjusting nut, then re-moving the cable from the brakecamshaft lever and brake shoeplate.
PERIODIC MAINTENANCE AND ADJUSTMENT
7-20
1
2
3
4
5
6
7
8
9
3. Remove the axle nut and washer.4. Pull the wheel axle out, and then
remove the wheel.
EAU41031
To install the front wheel
1. Install the brake shoe plate into thewheel hub as shown.
2. Lift the wheel up between the forklegs.
TIP
Make sure that the slot in the brakeshoe plate fits over the retainer on the
fork leg.
3. Insert the wheel axle from the rightside.
4. Install the washer and axle nut,and then tighten the axle nut to thespecified torque.
5. Connect the brake cable at thewheel hub, and then install thebrake cable free play adjusting nut.
6. Adjust the brake lever free play.(See page 7-15.)
7. Take the motorcycle off the center-stand so that the front wheel is onthe ground.
1. Brake lever free play adjusting nut2. Brake camshaft lever3. Washer4. Axle nut5. Brake cable
1. Wheel axle
5
1
2
3 4
1
1. Retainer
Tightening torque:
Axle nut:40 Nm (4.0 m·kgf, 28.9 ft·lbf)
1
PERIODIC MAINTENANCE AND ADJUSTMENT
7-21
2
3
4
5
6
7
8
9
8. Push down hard on the handlebarseveral times to check for properfork operation.
EAU25080
Rear wheel
EAU41082
To remove the rear wheel
WARNING
EWA10821
To avoid injury, securely support thevehicle so there is no danger of it
falling over.
1. Place the motorcycle on the cen-terstand.
2. Remove the seat. (See page 4-7.)3. Remove the muffler bolt and
washers.
WARNING! Always letthe exhaust system cool prior totouching exhaust compo-nents.
[EWA14581]
4. Slide the spring clamp down, andthen remove the muffler.
1. Muffler2. Washer3. Muffler bolt4. Spring clamp
1. Exhaust chamber2. Exhaust chamber bolt3. Washer
31 2
4
2
1
3
PERIODIC MAINTENANCE AND ADJUSTMENT
7-22
1
2
3
4
5
6
7
8
9
5. Remove the exhaust chamber boltand washers.
6. Remove the exhaust manifoldbolts, and then remove the ex-haust chamber.
7. Remove the right-side rear shockabsorber mounting bolt and thentilt the rear shock absorber upwardas shown.
8. Remove the axle nut while apply-ing the rear brake.
9. Remove the rear arm by removingthe nuts and washers.
10. Pull the wheel to the right to sepa-rate it from the final gear case, andthen remove the wheel.
EAU41521
To install the rear wheel
1. Apply a light coating of lithi-um-soap-based grease to thesplines of the final gear case andwheel hub.
2. Install the wheel by inserting it intothe wheel hub.
3. Install the rear arm by installing thewashers and nuts.
4. Install the axle nut.5. Install the right-side rear shock ab-
1. Exhaust manifold bolt
1
1. Rear shock absorber mounting bolt
1. Axle nut
1
1
1. Rear arm2. Washer3. Rear arm nut
1 23
PERIODIC MAINTENANCE AND ADJUSTMENT
7-23
2
3
4
5
6
7
8
9
sorber by installing the mountingbolt.
6. While applying the rear brake,tighten the axle nut to the specifiedtorque.
7. Tighten the rear arm nuts and rearshock absorber mounting bolt tothe specified torques.
8. Install the exhaust chamber andthen install the exhaust manifoldbolts.
9. Install the washers and exhaustchamber bolt.
10. Tighten the exhaust manifold boltsand exhaust chamber bolt to thespecified torques.
11. Install the muffler by sliding thespring clamp up to its original posi-tion, and then installing the wash-ers and muffler bolt.
TIP
Make sure that the spring clamp is po-sitioned with the projection side facing
inward.
12. Tighten the muffler bolt to thespecified torque.
13. Adjust the brake lever free play.(See page 7-15.)
14. Install the seat.
Tightening torques:
Axle nut:60 Nm (6.0 m·kgf, 43.4 ft·lbf)
Rear arm nut:28.5 Nm (2.9 m·kgf, 20.6 ft·lbf)
Rear shock absorber mounting bolt:22.5 Nm (2.3 m·kgf, 16.3 ft·lbf)
Tightening torques:
Exhaust manifold bolt:8.5 Nm (0.9 m·kgf, 6.1 ft·lbf)
Exhaust chamber bolt:17.5 Nm (1.8 m·kgf, 12.7 ft·lbf)
1. Exhaust chamber2. Spring clamp3. Muffler
Tightening torque:
Muffler bolt:17.5 Nm (1.8 m·kgf, 12.7 ft·lbf)
1
2
3
PERIODIC MAINTENANCE AND ADJUSTMENT
7-24
1
2
3
4
5
6
7
8
9
EAU25851
Troubleshooting
Although Yamaha motorcycles receivea thorough inspection before shipmentfrom the factory, trouble may occur dur-ing operation. Any problem in the fuel,compression, or ignition systems, forexample, can cause poor starting andloss of power.The following troubleshooting chartrepresents a quick and easy procedurefor checking these vital systems your-self. However, should your motorcyclerequire any repair, take it to a Yamahadealer, whose skilled technicians havethe necessary tools, experience, andknow-how to service the motorcycleproperly.Use only genuine Yamaha replace-ment parts. Imitation parts may look likeYamaha parts, but they are often inferi-or, have a shorter service life and canlead to expensive repair bills.
WARNING
EWA15141
When checking the fuel system, donot smoke, and make sure there areno open flames or sparks in the ar-ea, including pilot lights from water
heaters or furnaces. Gasoline orgasoline vapors can ignite or ex-plode, causing severe injury or
property damage.
PERIODIC MAINTENANCE AND ADJUSTMENT
7-25
2
3
4
5
6
7
8
9
EAU25972
Troubleshooting chart
Check the fuel level inthe fuel tank.
1. FuelThere is enough fuel.
There is no fuel.
Supply fuel.
Operate the kickstarter.
2. CompressionThere is compression.
There is no compression.
Check the ignition.
Have a Yamaha dealercheck the vehicle.
Remove the spark plugand check the electrodes.
3. IgnitionWet
Dry
Wipe off with a dry cloth and correct thespark plug gap, or replace the spark plug.
Have a Yamaha dealer check the vehicle.The engine does not start.Have a Yamaha dealer check the vehicle.
Open the throttle halfway and operatethe kickstarter.
Check the compression.
The engine does not start. Check the compression.
8-1
1
2
3
4
5
6
7
8
9
MOTORCYCLE CARE AND STORAGE
EAU37833
Matte color caution
NOTICE
ECA15192
Some models are equipped withmatte colored finished parts. Besure to consult a Yamaha dealer foradvice on what products to use be-fore cleaning the vehicle. Using abrush, harsh chemical products orcleaning compounds when cleaningthese parts will scratch or damagetheir surface. Wax also should notbe applied to any matte colored fin-
ished parts.
EAU40633
Care
While the open design of a motorcyclereveals the attractiveness of the tech-nology, it also makes it more vulnera-ble. Rust and corrosion can developeven if high-quality components areused. A rusty exhaust pipe may go un-noticed on a car, however, it detractsfrom the overall appearance of a motor-cycle. Frequent and proper care doesnot only comply with the terms of thewarranty, but it will also keep your mo-torcycle looking good, extend its lifeand optimize its performance.
Before cleaning
1. Cover the muffler outlet with aplastic bag after the engine hascooled down.
2. Make sure that all caps and coversas well as all electrical couplersand connectors, including thespark plug cap, are tightly in-stalled.
3. Remove extremely stubborn dirt,like oil burnt onto the crankcase,with a degreasing agent and abrush, but never apply such prod-
ucts onto seals, gaskets and wheelaxles. Always rinse the dirt and de-greaser off with water.
Cleaning
NOTICE
ECA10771
�
Avoid using strong acidic wheelcleaners, especially on spokedwheels. If such products areused on hard-to-remove dirt, donot leave the cleaner on the af-fected area any longer than in-structed. Also, thoroughly rinsethe area off with water, immedi-ately dry it, and then apply a cor-rosion protection spray.
�
Improper cleaning can damageplastic parts such as cowlings,panels, windshields, headlightlenses, meter lenses, etc. Useonly a soft, clean cloth orsponge with mild detergent andwater to clean plastic.
�
Do not use any harsh chemicalproducts on plastic parts. Besure to avoid using cloths orsponges which have been incontact with strong or abrasive
MOTORCYCLE CARE AND STORAGE
8-2
2
3
4
5
6
7
8
9
cleaning products, solvent orthinner, fuel (gasoline), rust re-movers or inhibitors, brake flu-id, antifreeze or electrolyte.
�
Do not use high-pressure wash-ers or steam-jet cleaners sincethey cause water seepage anddeterioration in the following ar-eas: seals (of wheel and swing-arm bearings, fork and brakes),electric components (couplers,connectors, instruments,switches and lights), breatherhoses and vents.
�
For motorcycles equipped witha windshield: Do not use strongcleaners or hard sponges asthey will cause dulling orscratching. Some cleaning com-pounds for plastic may leavescratches on the windshield.Test the product on a small hid-den part of the windshield tomake sure that it does not leaveany marks. If the windshield isscratched, use a quality plasticpolishing compound after
washing.
After normal useRemove dirt with warm water, a milddetergent, and a soft, clean sponge,and then rinse thoroughly with cleanwater. Use a toothbrush or bottlebrushfor hard-to-reach areas. Stubborn dirtand insects will come off more easily ifthe area is covered with a wet cloth fora few minutes before cleaning.
After riding in the rain or near the seaSince sea salt is extremely corrosive,carry out the following steps after eachride in the rain or near the sea.
1. Clean the motorcycle with cold wa-ter and a mild detergent, after theengine has cooled down.
NOTICE:
Do not use warm watersince it increases the corrosiveaction of the salt.
[ECA10791]
2. Apply a corrosion protection spray
on all metal, including chrome- andnickel-plated, surfaces to preventcorrosion.
After cleaning
1. Dry the motorcycle with a chamoisor an absorbing cloth.
2. Use a chrome polish to shinechrome, aluminum and stain-less-steel parts, including the ex-haust system. (Even the thermallyinduced discoloring of stain-less-steel exhaust systems can beremoved through polishing.)
3. To prevent corrosion, it is recom-mended to apply a corrosion pro-tection spray on all metal,including chrome- and nickel-plat-ed, surfaces.
4. Use spray oil as a universal clean-er to remove any remaining dirt.
5. Touch up minor paint damagecaused by stones, etc.
6. Wax all painted surfaces.7. Let the motorcycle dry completely
before storing or covering it.
WARNING
EWA14501
Contaminants on the brakes or tirescan cause loss of control.
�
Make sure that there is no oil orwax on the tires.
�
If necessary, wash the tires withwarm water and a mild deter-gent. Before riding at higherspeeds, test the motorcycle’s
MOTORCYCLE CARE AND STORAGE
8-3
1
2
3
4
5
6
7
8
9
braking performance and cor-
nering behavior.
NOTICE
ECA10800
�
Apply spray oil and wax spar-ingly and make sure to wipe offany excess.
�
Never apply oil or wax to anyrubber and plastic parts, buttreat them with a suitable careproduct.
�
Avoid using abrasive polishingcompounds as they will wear
away the paint.
TIP
Consult a Yamaha dealer for advice on
what products to use.
EAU40643
Storage
Short-term
Always store your motorcycle in a cool,dry place and, if necessary, protect itagainst dust with a porous cover.
NOTICE
ECA10810
�
Storing the motorcycle in apoorly ventilated room or cover-ing it with a tarp, while it is stillwet, will allow water and humid-ity to seep in and cause rust.
�
To prevent corrosion, avoiddamp cellars, stables (becauseof the presence of ammonia)and areas where strong chemi-
cals are stored.
Long-term
Before storing your motorcycle for sev-eral months:
1. Follow all the instructions in the“Care” section of this chapter.
2. For motorcycles equipped with afuel cock that has an “S” (stop) po-sition: Turn the fuel cock lever to
“S”.3. Drain the carburetor float chamber
by loosening the drain bolt; this willprevent fuel deposits from buildingup. Pour the drained fuel into thefuel tank.
4. Fill up the fuel tank and add fuelstabilizer (if available) to preventthe fuel tank from rusting and thefuel from deteriorating.
5. Perform the following steps to pro-tect the cylinder, piston rings, etc.from corrosion.a. Remove the spark plug cap
and spark plug.b. Pour a teaspoonful of engine oil
into the spark plug bore.c. Install the spark plug cap onto
the spark plug, and then placethe spark plug on the cylinderhead so that the electrodes aregrounded. (This will limit spark-ing during the next step.)
d. Turn the engine over severaltimes with the starter. (This willcoat the cylinder wall with oil.)
e. Remove the spark plug capfrom the spark plug, and then
MOTORCYCLE CARE AND STORAGE
8-4
2
3
4
5
6
7
8
9
install the spark plug and thespark plug cap.
WARNING! Toprevent damage or injuryfrom sparking, make sure toground the spark plug elec-trodes while turning the en-gine over.
[EWA10951]
6. Lubricate all control cables and the
pivoting points of all levers andpedals as well as of the center-stand.
7. Check and, if necessary, correctthe tire air pressure, and then liftthe motorcycle so that both of itswheels are off the ground. Alterna-tively, turn the wheels a little everymonth in order to prevent the tiresfrom becoming degraded in onespot.
8. Cover the muffler outlet with aplastic bag to prevent moisturefrom entering it.
TIP
Make any necessary repairs before
storing the motorcycle.
9-1
1
2
3
4
5
6
7
8
9
SPECIFICATIONS
EAU2633N
Dimensions:
Overall length: 1245 mm (49.0 in)
Overall width: 575 mm (22.6 in)
Overall height: 715 mm (28.1 in)
Seat height: 485 mm (19.1 in)
Wheelbase: 855 mm (33.7 in)
Ground clearance: 105 mm (4.13 in)
Minimum turning radius: 1300 mm (51.2 in)
Weight:
With oil and fuel: 39.0 kg (86 lb)
Engine:
Engine type: Air cooled 2-stroke
Cylinder arrangement: Forward-inclined single cylinder
Displacement: 49.0 cm
3
Bore
×
stroke: 40.0
×
39.2 mm (1.57
×
1.54 in)Compression ratio:
6.00 :1Starting system:
Kickstarter
Lubrication system: Separate lubrication (Yamaha autolube)
Engine oil:
Type: YAMALUBE 2 or 2-stroke engine oil (JASOFC grade) or (ISO EG-C or EG-D grade)
Engine oil quantity:
Quantity: 0.30 L (0.32 US qt, 0.26 Imp.qt)
Transmission oil:
Type: YAMALUBE 4 (10W-40) or SAE 10W-40
Oil change quantity: 0.30 L (0.32 US qt, 0.26 Imp.qt)
Air filter:
Air filter element: Wet element
Fuel:
Recommended fuel: Unleaded gasoline only
Fuel tank capacity: 2.0 L (0.53 US gal, 0.44 Imp.gal)
Carburetor:
Manufacturer: MIKUNI
Type
×
quantity: VM12SC x 1
Spark plug (s):
Manufacturer/model: NGK/BP4HS
Manufacturer/model: DENSO/W14FPL
Spark plug gap: 0.6–0.7 mm (0.024–0.028 in)
Clutch:
Clutch type: Wet, centrifugal automatic
Transmission:
Primary reduction system: Spur gear
Primary reduction ratio: 63/33 (1.909)
Secondary reduction system: Shaft drive
Secondary reduction ratio: 19/15
×
54/11 (6.218)
Chassis:
Frame type: Steel tube backbone
Caster angle: 25.50 °
Trail: 50.0 mm (1.97 in)
Front tire:
Type: With tube
Size: 2.50-10 4PR
Manufacturer/model: BRIDGESTONE/KNOBBY
Manufacturer/model: IRC/KNOBBY
Rear tire:
Type: With tube
SPECIFICATIONS
9-2
2
3
4
5
6
7
8
9
Size: 2.50-10 4PR
Manufacturer/model: BRIDGESTONE/KNOBBY
Manufacturer/model: IRC/KNOBBY
Loading:
Maximum rider weight: 25.0 kg (55 lb)
* (Total weight of rider, cargo and accessories)
Tire air pressure (measured on coldtires):
Front: 100 kPa (1.00 kgf/cm
2
, 15 psi)Rear:
100 kPa (1.00 kgf/cm
2
, 15 psi)
Front wheel:
Wheel type: Panel wheel
Rim size: 10x1.50
Rear wheel:
Wheel type: Panel wheel
Rim size: 10x1.50
Front brake:
Type: Drum brake
Operation: Right hand operation
Rear brake:
Type: Drum brake
Operation: Left hand operation
Front suspension:
Type: Telescopic fork
Spring/shock absorber type: Coil spring/oil damper
Wheel travel: 60.0 mm (2.36 in)
Rear suspension:
Type: Unit swing
Spring/shock absorber type: Coil spring/oil damper
Wheel travel: 50.0 mm (1.97 in)
Electrical system:
Ignition system: CDI
10-1
1
2
3
4
5
6
7
8
9
10
CONSUMER INFORMATION
EAU40790
Identification numbers
Record the vehicle identification num-ber and model label information in thespaces provided below for assistancewhen ordering spare parts from aYamaha dealer or for reference in casethe vehicle is stolen.VEHICLE IDENTIFICATION NUMBER:
MODEL LABEL INFORMATION:
EAU26400
Vehicle identification number
The vehicle identification number isstamped into the steering head pipe.Record this number in the space pro-vided.
TIP
The vehicle identification number isused to identify your motorcycle andmay be used to register your motorcy-cle with the licensing authority in your
area.
EAU26480
Model label
The model label is affixed to the frameunder the seat. (See page 4-7.) Recordthe information on this label in thespace provided. This information will beneeded when ordering spare parts froma Yamaha dealer.
1. Vehicle identification number
1
1. Model label
1
CONSUMER INFORMATION
10-2
2
3
4
5
6
7
8
9
10
EAU26560
Motorcycle noise regulation
TAMPERING WITH NOISE CONTROL SYSTEM PROHIBITED:
Federal law prohibits the following acts or the causing thereof: (1) The removal or rendering inoperative by any person otherthan for purposes of maintenance, repair, or replacement of any device or element of design incorporated into any new ve-hicle for the purpose of noise control prior to its sale or delivery to the ultimate purchaser or while it is in use or (2) the use ofthe vehicle after such device or element of design has been removed or rendered inoperative by any person.“AMONG THOSE ACTS PRESUMED TO CONSTITUTE TAMPERING ARE THE ACTS LISTED BELOW”.These acts include tampering with the following systems; i.e., modification, removal, etc.
Exhaust system
�
Muffler
�
Exhaust pipe
�
Silencer
Intake system
�
Air cleaner case
�
Air cleaner element
�
Intake duct
CONSUMER INFORMATION
10-3
1
2
3
4
5
6
7
8
9
10
EAU38051
YAMAHA MOTOR CORPORATION, U.S.A. OFF-ROAD MOTORCYCLE LIMITED WARRANTY Yamaha Motor Corporation, USA hereby warrantsthat new Yamaha off-road motorcycles purchasedfrom an authorized Yamaha motorcycle dealer inthe continental United States will be free fromdefects in material and workmanship for the peri-od of time stated herein, subject to certain statedlimitations. Covered off-road motorcycles arethose units certified by Yamaha to EPA noise reg-ulations and come equipped from the factory withUSDA-FS approved spark arresters.
THE PERIOD OF WARRANTY for Yamaha off-road motorcycles shall be ninety (90) days fromthe date of purchase, with no mileage limitation.
PRODUCT EXCLUDED FROM WARRANTYinclude those used for non-Yamaha-authorizedrenting, leasing, or other commercial purposes.
DURING THE PERIOD OF WARRANTY anyauthorized Yamaha motorcycle dealer will free ofcharge, repair or replace, at Yamaha's option, anypart adjudged defective by Yamaha due to faultyworkmanship or material from the factory. Partsused in warranty repairs will be warranted for thebalance of the product's warranty period. All partsreplaced under warranty become property ofYamaha Motor Corporation, USA.
GENERAL EXCLUSIONS from this warrantyshall include any failures caused by:a. Competition or racing use.b. Installation of parts or accessories that are
not qualitatively equivalent to genuineYamaha parts.
c. Abnormal strain, neglect, or abuse.d. Lack of proper maintenance.e. Accident or collision damage.f. Modification to original parts.g. Damage due to improper transportation.
SPECIFIC EXCLUSIONS from this warranty shallinclude parts replaced due to normal wear or rou-tine maintenance.
THE CUSTOMER'S RESPONSIBILITY underthis warranty shall be to:1. Operate and maintain the motorcycle as
specified in the appropriate Owner's Manual,and
2. Give notice to an authorized Yamaha motor-cycle dealer of any and all apparent defectswithin ten (10) days after discovery, and makethe motorcycle available at that time forinspection and repairs at such dealer's placeof business.
WARRANTY TRANSFER: To transfer the warran-ty from the original purchaser to any subsequentpurchaser(s), it is imperative that the motorcyclebe inspected and registered for warranty by anauthorized Yamaha motorcycle dealer. In order forthis warranty to remain in effect, this inspectionand registration must take place within ten (10)days after transfer of ownership to the subse-quent purchaser. A reasonable dealer imposedfee may be charged for this inspection.
EMISSION CONTROL SYSTEM WARRANTYYamaha Motor Corporation, USA also warrants tothe ultimate purchaser and each subsequent pur-chaser of each 2006 and later model Yamahamotorcycle covered by this warranty that the vehi-cle is designed, built, and equipped so as to con-form at the time of sale with all U.S. emissionsstandards applicable at the time of manufactureand that it is free from defects in materials andworkmanship which would cause it not to meetthese standards within the period listed immedi-ately below. Failures other than those resultingfrom defects in material or workmanship which
arise solely as a result of owner abuse and/or lackof proper maintenance are not covered by thiswarranty.
All Off-Road ModelsThirty (30) months from the original purchasedate
YAMAHA MOTOR CORPORATION, USAMAKES NO OTHER WARRANTY OF ANYKIND, EXPRESSED OR IMPLIED. ALL IMPLIEDWARRANTIES OF MERCHANTABILITY ANDFITNESS FOR A PARTICULAR PURPOSEWHICH EXCEED THE OBLIGATIONS ANDTIME LIMITS STATED IN THIS WARRANTYARE HEREBY DISCLAIMED BY YAMAHAMOTOR CORPORATION, USA AND EXCLUD-ED FROM THIS WARRANTY.
SOME STATES DO NOT ALLOW LIMITATIONSON HOW LONG AN IMPLIED WARRANTYLASTS, SO THE ABOVE LIMITATION MAY NOTAPPLY TO YOU. ALSO EXCLUDED FROM THISWARRANTY ARE ANY INCIDENTAL OR CON-SEQUENTIAL DAMAGES INCLUDING LOSSOF USE. SOME STATES DO NOT ALLOW THEEXCLUSION OR LIMITATION OF INCIDENTALOR CONSEQUENTIAL DAMAGES, SO THEABOVE EXCLUSION MAY NOT APPLY TO YOU.
THIS WARRANTY GIVES YOU SPECIFICLEGAL RIGHTS, AND YOU MAY ALSO HAVEOTHER RIGHTS WHICH VARY FROM STATE TOSTATE.
YAMAHA MOTOR CORPORATION, USAPost Office Box 6555
Cypress, California 90630
CONSUMER INFORMATION
10-4
2
3
4
5
6
7
8
9
10
CONSUMER INFORMATION
10-5
1
2
3
4
5
6
7
8
9
10
EAU26750
YAMAHA EXTENDED SERVICE (Y.E.S.) Keep your Yamaha protected even after your warranty expires with genuine Yamaha Extended Service (Y.E.S.).
Y.E.S. is designed and administered by Yamaha Motor Corporation to provide maximum owner satisfaction. You get uninterrupted factory-backed coverage for extra peace of mind.
Y.E.S. is flexible. You choose the plan that’s right foryou: 12 months, 24 months, 36 months or, on certain models, even 48 months beyond your warranty period.
Y.E.S. is designed and administered by the same Yamaha people who handle your warranty – and itshows in the comprehensive coverage benefits. There are no mileage limitations. Coverage isn’t limited to “moving parts” or the “drive train” like many other plans. And Y.E.S. covers manufacturing defects just like the warranty. See the sample contract at your Yamahadealer to see how comforting uninterrupted factory-backed protection can be.
You don’t have to pay anything for covered repairs. There’s no deductible to pay, and repairs aren’t“pro-rated.” You don’t have any “out-of-pocket” expenses for covered repairs.
In addition, Travel and Recreation Interruption Protection (TRIP) is included at no extra cost. TRIP gives you up to $150 reimbursement per occurrence for any reasonable expenses you incur because your Yamaha needs covered service: replacement vehicle rental, emergency towing, phone calls, even food and lodging when you are away from home. This superb coverage goes into effect when you purchase Y.E.S., so it applies to any warranty repairs as well as covered repairs during your entire Y.E.S. plan period.
Y.E.S. coverage is honored at any authorized Yamaha dealer nationwide.
Y.E.S. coverage is transferable to a new owner if yousell or trade-in. That can make your Yamaha much more valuable!
This excellent Y.E.S. plan coverage is only available to Yamaha owners like you, and only while your Yamaha is still within the Yamaha Limited Warranty period. So visit your authorized Yamaha dealer to get all the facts. He can show you how easy it is to protect your investment with Yamaha Extended Service.
CONSUMER INFORMATION
10-6
2
3
4
5
6
7
8
9
10
We urge you to act now. You’ll get the excellent benefits of TRIP coverage right away, and you’ll rest easy knowing you’ll have strong factory-backed protection even after your Yamaha Limited Warranty expires.
A special note:If visiting your dealer isn’t convenient, contact Yamaha with your Primary ID number (your frame number). We’ll be happy to help you get the Y.E.S. coverage you need.
Yamaha Service MarketingP.O. Box 6555Cypress, CA 906301-(866)-YES-EXTD (1-866-937-3983)
INDEX
A
Acceleration and deceleration................... 6-2Air filter element, cleaning......................... 7-9Autolube pump, adjusting ....................... 7-17
B
Brake lever, front....................................... 4-2Brake lever, rear ....................................... 4-3Brake levers, lubricating.......................... 7-17Brake shoes, checking............................ 7-16Braking...................................................... 6-2
C
Cables, checking and lubricating ............ 7-16Carburetor, adjusting .............................. 7-11Care .......................................................... 8-1Centerstand, checking and lubricating.... 7-18
E
Engine break-in......................................... 6-3Engine idling speed................................. 7-11Engine oil .................................................. 4-5Engine, starting a warm ............................ 6-1Engine stop switch .................................... 4-1
F
Front and rear brake lever free play, adjusting ............................................... 7-15
Front fork, checking ................................ 7-18Fuel ........................................................... 4-3Fuel cock................................................... 4-5Fuel tank breather hose ............................ 4-5Fuel tank cap ............................................ 4-3
H
Handlebar switch ...................................... 4-1
I
Identification numbers............................. 10-1
K
Kickstarter..................................................4-6
L
Location of important labels.......................1-1
M
Maintenance and lubrication, periodic .......7-4Maintenance, emission control system......7-3Matte color, caution ...................................8-1Middle and final gear cases.......................7-9Model label ..............................................10-1
N
Noise regulation.......................................10-2
P
Parking.......................................................6-4Part locations.............................................3-1Power reduction plate, removing ...............7-7Pre-operation check list .............................5-2
S
Safety information......................................2-1Seat ...........................................................4-7Spark arrester, cleaning...........................7-10Spark plug, checking .................................7-6Specifications.............................................9-1Speed limiter and power reduction plate ...4-1Starter (choke) lever ..................................4-6Starting and warming up a cold engine .....6-1Starting off .................................................6-2Steering, checking ...................................7-19Storage ......................................................8-3
T
Throttle cable free play, checking............7-12Throttle grip and cable, checking and
lubricating ..............................................7-17Tires.........................................................7-12
Tool kit .......................................................7-2Transmission oil ........................................7-8Troubleshooting.......................................7-24Troubleshooting chart..............................7-25
V
Vehicle identification number ..................10-1
W
Warranty, extended .................................10-5Warranty, limited .....................................10-3Wheel bearings, checking .......................7-19Wheel (front)............................................7-19Wheel (rear) ............................................7-21Wheels ....................................................7-14
PRINTED ON RECYCLED PAPERYAMAHA MOTOR CO., LTD.
PRINTED IN JAPAN2008.4–0.7×1 !
(E)