Purchase and Commissioning of Various Lab Equipment of ...
-
Upload
phungquynh -
Category
Documents
-
view
214 -
download
0
Transcript of Purchase and Commissioning of Various Lab Equipment of ...
KAMLA NEHRU INSTITUTE OF TECHNOLOGY, SULTANPUR (U.P.) 228118
Tender No: 02/MKR/2014-15
Tender Notice
Director, KNIT Sultanpur invites sealed Tenders from eligible bidders for supply and commissioning of Lab Equipments for different departments of Manyawar Kanshi Ram Engineering College of Information Technology Ambedkar Nagar. Separate tenders must be submitted at KNIT Sultanpur for each package of following Departments: 1. Civil Engg. 2. Electrical Engg. 3. Information Technology 4. Workshop /Physics / Chemistry
The tender documents can be downloaded from the Institute website www.knit.ac.in and may be
submitted by 25.03.2015 upto 02:00 PM. Tenders will be opened on the same day at 03:00 PM in the committee room of KNIT Sultanpur. Cost of tender document and EMD as mentioned in the tender document should be in the form of separate bank draft in favour of Director, K.N.I.T. Sultanpur payable at Sultanpur (U.P.). Director reserves all rights to reject any or all tenders without assigning any reason thereof. For Tender Cost, EMD, Specifications and other details please visit our website: www.knit.ac.in
REGISTRAR
KAMLA NEHRU INSTITUTE OF TECHNOLOGY SULTNAPUR (U.P) -228118
TENDER DOCUMENT
(FOR MANYAWAR KASHI RAM ENGINEERING COLLEGE OF INFORMATION TECHNOLOGY AMBEDKARNAGAR)
No: MKR/Tender-01/2/2015 Date: 09.03.2015
Opening Date: 25.03.2015 Opening Time: 03.00 PM Opening Place: Committee Room
KNIT Sultanpur
Sealed and separate tenders in duplicate in two parts i.e. tender bid-I and tender bid-II are herewith
invited for Supply & Commissioning of Laboratory Equipments at MKRECIT
Ambedkarnagar along with earnest money amounting to Rs…. (Mentioned with package/unit) in
the shape of Demand Draft of Nationalized/Scheduled Bank in favour of Director KNIT Sultanpur
Avadh (UP). Both envelopes should be kept in one big envelope. The tenders should reach to
undersigned latest by 25.03.2015 at 2.00 PM.
Tenders are being invited to purchase and commissioning of equipments to establish various laboratories. Each laboratory will be treated as one package /unit. It is expected that a firm selected for the establishment of a laboratory shall supply all equipments of that laboratory. The firm will also complete the work of installation/ mounting and commissioning of these equipments. This include concrete foundation work (in case of heavy machines), electrical safety, electricity wiring in the laboratory to make these equipments functional.
Terms & Conditions:
1. Details of equipments/ materials are as per bill of quantity attached. 2. Tenders should be submitted either in person or by post in sealed envelopes on which name
of package/unit, tender number and date along with name and address of the firm will be written.
3. TENDER BID-I (Technical) shall contain (i) Tender cost (non refundable) (ii) Earnest Money (iii) Proof of PAN and TIN registration document (iv) Standing of the firm (v) Major supplies executed in recent past (vi) Authorized dealer certificate from OEM & Commercial terms and conditions. TENDER BID-II (Financial) shall contain rate schedule only. The rates must be quoted in both figures and words. Any overwriting and/or cutting must be duly attested failing which tenders are likely to be rejected.
4. All tenders received after due date and time will not be considered. 5. Price quoted should be F.O.R. Manyawar Kanshi Ram Engineering College of
Information Technology Ambedkarnagar (UP). 6. The detailed specifications and make of the equipments /material must be given. 7. The quoted items should strictly be in order of merit with serial number and metric unit
otherwise the tenders are liable to be ignored.
2
8. Conditions regarding validity of tenders, delivery period, payment discount, warrantee and Guarantee Period, Trade Tax, Excise & Custom Duty and insurance etc. should be mentioned clearly. Net prices should be quoted.
9. No sales tax form “C” or “D” etc. for concessional rates shall be provided by the Institute. 10. The quoted rates should be valid for at least six months from the date of opening. 11. Tenders without sample wherever required may not be accepted. 12. In case of imported equipment, commission allowed to agents must be specifically mentioned. 13. Free demonstration shall be done in the Institute premises if required. 14. Insurance shall be done by the suppliers at their own cost. 15. Tenders without mentioned earnest money deposit will not be entertained. 16. Standing of the firm and major supplies in recent past with proof must be attached. 17. In case of dealers, authorized distributors, dealer’s certificate from OEM is required. 18. Document through bank and advance payment on proforma invoice may not be accepted. 19. The quantity mentioned in bill of quantity against each items will be treated as provisional and
it may be changed depending on actual requirement. 20. Payment will be made only after successful installation and operation in the concerned
department after verification from the departments. 21. If the supply is not made within prescribe period the firm shall be liable to pay a penalty equal
to 0.10% of value of purchase order per day. However this can be waved off by the Director under special circumstances. If the firm fails to supply the equipments earnest money deposit will be forfeited.
22. Deduction of TDS as per Govt. Rules. 23. Tenders will be opened in the presence of those who choose to be present on the opening
date and time. 24. Any dispute will be subjected to Sultanpur (UP) Jurisdiction only. 25. Conditional tenders will not be accepted. 26. The Director reserves the right to accept or reject any or all tenders without assigning any
reason.
Officer In Charge Purchase KNIT Sultanpur
KAMLA NEHRU INSTITUTE OF TECHNOLOGY SULTNAPUR (U.P) -228118
TENDER DOCUMENT
(FOR MANYAWAR KASHI RAM ENGINEERING COLLEGE OF INFORMATION TECHNOLOGY AMBEDKARNAGAR)
Bidders Proforma
Tender Purchase and Commissioning of Equipments for Electrical Engg. lab of Electrical Engg Department
Name of the firm with full address and contact number
FOR Manyawar Kanshi Ram Engineering College of Information Technology Ambedkarnagar (Located on Akbarpur-Tanda Road at 700 mt from collectrate Ambedkarnagar)
Cost of Tender Document DD No: Amount: Bank: Date: Drawn on favour of Director KNIT payable at Sultanpur
Earnest Money Deposit DD No: Amount: Bank: Date: Drawn on favour of Director KNIT payable at Sultanpur
PAN/TIN/TAN No PAN: TIN: TAN: (Attach proof)
Original Equipment Manufacturers /Authorization Letter from O.E.M.
Attach proof
Turnover in the last three years
Attach proof
Details of Similar Work Executed during last Three years
Attach proof
Signature and Seal of Bidders
Department of Electrical Engineering
Package –MKR/EE/01 -Electrical Engineering Laboratory
Tender Cost: Rs. 200.00 EMD- Rs. 7280.00
Bill of Quantity for Electrical Engineering Lab:
Sr.
No.
Name of Equipment with specifications Qty. Unit Cost Total Cost Remarks
1. Complete Setup For performing :- Verification of Kirchhoff’s laws (KVL/KCL)
02
2. Complete Setup For performing :- Verification of (i) Superposition theorem (ii)
Thevenin’s Theorem (iii) Maximum Power
Transfer Theorem.
02
3. Complete Setup For performing :- Measurement of power and power factor in a
single phase ac series inductive circuit and
study improvement of power factor using
capacitor
02
4. Complete Setup For performing :- Study of phenomenon of resonance in RLC
series circuit and obtain resonant frequency.
02
5. Complete Setup For performing :- Measurement of power in 3- phase circuit by
two wattmeter method and determination of its
power factor.
02
6. Complete Setup For performing :- Determination of parameters of ac single phase
series RLC circuit
02
7. Complete Setup For performing :- Determination of (i) Voltage ratio (ii) polarity
and (iii) efficiency by load test of a single
phase transformer
02
8. Complete Setup For performing :- To measure energy by a single phase energy
meter and determine error.
02
9. Complete Setup For performing :- To study P-N diode characteristics
02
10. Complete Setup For performing :- To study full wave and half wave rectifier
circuits with and without capacitor and
determine ripple factors.
02
11. Complete Setup For performing :- To study various logic gates (TTL)
02
12. Complete Setup For performing :- To study Operational Amplifier as Adder and
Sub tractor
02
13. Complete Setup For performing :- To study transistor as a switch.
02
14. Rheostat up to 2000 Ohm,10Amp 10
15. DC Regulated Power Supply 0-30 Volt,
5Amp.
05
16. Bread Board With Power Supply ± 0-15 Volt
in Box
05
17. Digital Multi-meter 05
18. C.R.O. up to 30 MHz 05
Total
KAMLA NEHRU INSTITUTE OF TECHNOLOGY SULTNAPUR (U.P) -228118
TENDER DOCUMENT
(FOR MANYAWAR KASHI RAM ENGINEERING COLLEGE OF INFORMATION TECHNOLOGY AMBEDKARNAGAR)
Bidders Proforma
Tender Purchase and Commissioning of Equipments for DC Supply for Electrical Engg Department
Name of the firm with full address and contact number
FOR Manyawar Kanshi Ram Engineering College of Information Technology Ambedkarnagar (Located on Akbarpur-Tanda Road at 700 mt from collectrate Ambedkarnagar)
Cost of Tender Document DD No: Amount: Bank: Date: Drawn on favour of Director KNIT payable at Sultanpur
Earnest Money Deposit DD No: Amount: Bank: Date: Drawn on favour of Director KNIT payable at Sultanpur
PAN/TIN/TAN No PAN: TIN: TAN: (Attach proof)
Original Equipment Manufacturers /Authorization Letter from O.E.M.
Attach proof
Turnover in the last three years
Attach proof
Details of Similar Work Executed during last Three years
Attach proof
Signature and Seal of Bidders
Department of Electrical Engineering
Package –MKR/EE/02 -Electrical Engineering Laboratory
Tender Cost: Rs. 200.00 EMD- Rs. 5680.00
1. DC Supply (250V-50A)
SINGLE PHASE RECTIFIER UNIT (WITH TRANSFORMER) VARIAC CONTROLLED Consisting of :-
1. MC Voltmeter 0-300 V 1 No.
2. MC Ammeter 0-25 A 1 No.
3. MI Voltmeter 0-300 V 1 No.
4. MI Ammeter 0-20 A 1 No.
5. Indicating Light for DC supply 1 No.
6. Indicating Light for 1 Phase AC supply 1 No.
7. MCB for AC supply
8. HRC Fuse for DC output
9. Rotary Switch for DC supply ON/OFF
10. Rotary Switch for AC input supply variation in steps.
11. Insulated terminals for AC supply and DC supply.
SPECIFICATIONS Input Voltage: Single Phase AC, 230V, 50 Hz, variable in steps through rotary switch.
Output Voltage: DC continuously variable by varying auto transformer.
Diodes: RUTTANSHAH/USHA make. All the diodes are duly matched current
sharing-wise during testing for long life operation of the equipment.
Transformer: This will be torroidal type transformer. The transformer will have
tappings for varying the input voltage to desired value by means of
rotary switch.
Variac: It is a continuously variable voltage auto transformer having a movable
carbon tip, fixed to brush arm sliding on a silver plated commutator.
Rotation of the brush arm by manual rotation delivers an output
voltage from 0 to or above line voltage by about 5%.
Capacity: 20 Amp.
RATINGS
1. Single Phase Rectifier Unit (with Transformer) (Variac Controlled) 20 Amp
2. Price for type 250/50 suitable for D.C. Output of 250V, 50 A
Alternatively
3. Price for type 250/60 suitable for D.C. Output of 250V, 60 A
Alternatively
4. Price for type 250/80 suitable for D.C. Output of 250V, 80 A
KAMLA NEHRU INSTITUTE OF TECHNOLOGY
SULTNAPUR (U.P) -228118
TENDER DOCUMENT
(FOR MANYAWAR KASHI RAM ENGINEERING COLLEGE OF INFORMATION TECHNOLOGY AMBEDKARNAGAR)
Bidders Proforma
Tender Purchase and Commissioning of Equipments for Electromechanical Energy Conversion lab I of Electrical Engg Department
Name of the firm with full address and contact number
FOR Manyawar Kanshi Ram Engineering College of Information Technology Ambedkarnagar (Located on Akbarpur-Tanda Road at 700 mt from collectrate Ambedkarnagar)
Cost of Tender Document DD No: Amount: Bank: Date: Drawn on favour of Director KNIT payable at Sultanpur
Earnest Money Deposit DD No: Amount: Bank: Date: Drawn on favour of Director KNIT payable at Sultanpur
PAN/TIN/TAN No PAN: TIN: TAN: (Attach proof)
Original Equipment Manufacturers /Authorization Letter from O.E.M.
Attach proof
Turnover in the last three years
Attach proof
Details of Similar Work Executed during last Three years
Attach proof
Signature and Seal of Bidders
Department of Electrical Engineering
Package –MKR/EE/03 - ELECTROMECHANICAL ENERGY CONVERSION LAB – I
Tender Cost: Rs. 200.00 EMD- Rs. 13160.00
BILL OF QUANTITY FOR ELECTROMECHANICAL ENERGY CONVERSION LAB – I:
Sr.
No.
Name of Equipment with Specifications Qty. Unit Cost Total Cost Remarks
1. Complete Setup For performing :-
To obtain magnetization characteristics of a DC
Shunt Generator
MACHINES REQUIRED
D.C. Shunt Motor, 2 HP, 230 V, 1500 RPM, (Prime
Mover) flexibly coupled to Shunt Generator 1.0 KW
(self-excited). Both the machines flexibly coupled
and mounted on M S channel base.
D.C. SHUNT MOTOR :
Type: DC Motor, shunt wound, self-excited, screen
protected, horizontal foot mounted, fan cooled,
provided with inter poles with DC starter face plate
type.
Capacity : 2 HP
Winding : Shunt wound.
R.P.M. : 1500
Volts. : 230
Insulation : Class ‘B’
Connections: All the terminals of armature and shunt
field shall be brought over to a Bakelite sheet, fixed
to C.I. terminal box, fitted on top of Motor.
D.C. SHUNT GENERATOR :
Type: DC Generator, Shunt wound, self-excited,
screen protected, horizontal foot mounted, and fan
cooled, provided with inter poles.
Capacity : 1.0 KW,
R.P.M. : 1500
Volts. : 230
Insulation : Class ‘B’
Connections: All the terminals of armature and shunt
field shall be brought over to a Bakelite sheet, fixed
to C.I. terminal box, fitted on top of Motor.
Both the machines are flexibly coupled and mounted
on sturdy m.s. channel base. The terminals of
armature, shunt and series field windings of both the
machines shall be brought over to Bakelite plate
fixed on C.I. terminal box fitted on top of machine.
CONTROL PANEL FOR MG SET : DC SHUNT
MOTOR & DC SHUNT GENERATOR
With
All Measuring instruments required as per
Experiment (Fitted on Engraved Bakelite sheet
enclosed in almirah type M S box with lock &
handle arrangement suitable for table mounting.)
1
2. Complete Setup For performing :-
To obtain load characteristics of a D.C.. shunt
generator and compound generator
(a)Cumulatively compounded (b)
1
Differentially compounded
D.C. Power supply
Fixed : 200 V
Variable : 0-200 V
DC Machine
Type : DC Shunt
Rating : 1 HP
RPM : 1500 (No Load)
Tachometer :20,000 RPM
With
All Measuring instruments required as per
Experiment
(Fitted on Engraved Bakelite sheet enclosed in
almirah type M S box with lock & handle
arrangement suitable for table mounting.)
3. Complete Setup For performing :-
To obtain efficiency of a dc shunt machine using
Swinburne’s test
Swinburne test of DC Machine:-
Input Supply : 200 V Fixed DC
: 0-200 V Variable
DC
DC Machine specification
Type : DC Shunt
Rating : 1 HP
Voltage Rating : 200 Volt
RPM : 1500 (No Load)
With
All Measuring instruments required as per
Experiment
(Fitted on Engraved Bakelite sheet enclosed in
almirah type M S box with lock & handle
arrangement suitable for table mounting.)
1
4. Complete Setup For performing :-
To perform Hopkinson’s test and determine losses
and efficiency of DC machine. Hopkinson
test of DC Machine:-
Input Supply : 200 V Fixed DC
: 0-200 V Variable
DC
DC Machine specification (2 Nos)
Both the Machines are flexibly coupled and mounted
on a M.S. channel base act as a Motor Generator set.
Type : DC Shunt
Rating : 1 HP
Voltage Rating : 200 Volt
RPM : 1500 (No Load)
Insulation : Class B
With
All Measuring instruments required as per
Experiment
(Fitted on Engraved Bakelite sheet enclosed in
almirah type M S box with lock & handle
arrangement suitable for table mounting.)
1
5. Complete Setup For performing :-
1.To obtain speed control of dc shunt motor using (a)
armature resistance control (b) field
control
2. To obtain speed-torque characteristics of a dc
1
shunt motor. D.C.
Power supply
Fixed : 200 V
Variable : 0-200 V
DC Machine
Type : DC Shunt
Rating : 1 HP
RPM : 1500 (No Load)
Tachometer :20,000 RPM
With
All Measuring instruments required as per
Experiment
(Fitted on Engraved Bakelite sheet enclosed in
almirah type M S box with lock & handle
arrangement suitable for table mounting.)
6. Complete Setup For performing :-
To obtain speed control of dc separately excited
motor using Conventional Ward-Leonard/ Static
Ward –Leonard method. Ward
Leonard Method of DC Machine:- Main Supply : Three Phase ,415
Volt
Machine Specification (2 Nos.)
Both the Machine are flexibly coupled and
mounted on a M.S. channel base act as a Motor
Generator set.
AC Three phase Squirrel Cage Induction Motor
acts as a Prime Mover
Rating :1 HP
Voltage Rating :415 Volt
RPM :1440 (No Load)
Insulation :Class B
DC Shunt Motor
Rating :1 HP
Voltage Rating :200 Volt
RPM :1500 (No Load)
Insulation :Class B
Extra DC Shunt Motor 200 Volt for which the
speed can be controlled using Motor Generator
set.
Rating :1/2 HP
Voltage Rating :200 Volt
RPM :1500 (No Load)
Insulation :Class B
With
All Measuring instruments required as per
Experiment
(Fitted on Engraved Bakelite sheet enclosed in
almirah type M S box with lock & handle
arrangement suitable for table mounting.)
1
7. Complete Setup For performing :-
1. To study polarity and ratio test of single phase and
3-phase transformers.
2. To obtain equivalent circuit, efficiency and voltage
regulation of a Single phase transformer using O.C.
and S.C. tests.
3. To obtain efficiency and voltage regulation of a
single phase transformer by Sumpner’s test.
POLARITY, VOLTAGE RATIO AND O.C. &
1
S.C. TEST ON 3 PHASE TRANSFORMER
Transformer Three Phase,3 KVA, 400/230V, 50 Hz,
air cooled, copper double wound with tapings at 50%
on primary & secondary side housed in M S box
with rubber footings. All the connections of primary
& secondary winding with tapings shell be brought
over to insulated Bakelite sheet fixed on top of
transformer. The transformer can be CORE type.
CONTROL PANEL
Fitted on ENGRAVED Bakelite sheet enclosed in
almirah type M S box with lock & handle
Arrangement suitable for table mounting.
1. MI Ammeter 96 x 96 mm 0-2A 1 No.
2. MI Ammeter 96 x 96 mm 0-10A 2 Nos.
3. MI Voltmeter 96 x 96 mm 0- 300 V 2 Nos.
4. MI Voltmeter 96 x 96 mm 0- 600 V 2 Nos.
5. Educational type Insulating Terminals
6. Indicating Light
7. TP MCB
8. LPF Wattmeter 2.5/5 Amp 150/300/600V
2 Nos.
Additional Accessories
3 Phase Variac 0-470V 1 No.
OPEN CIRCUIT AND SHORT CIRCUIT
TESTS ON SINGLE PHASE TRANSFORMER
MACHINE REQUIRED
Single Phase Transformer 2 KVA, 230/230V with
Tapings at 50% & 86.6% Naturally Air Cooled
Copper Double wound, Shell type. The transformer
will be housed in MS sheet box enclosure with
rubber footings. All the terminals of primary &
secondary shall be brought over to Bakelite sheet
fitted on top of the box through insulated terminals.
CONTROL PANEL FOR EXPERIMENT
Fitted on Bakelite sheet enclosed in almirah type M
S box with lock & handle arrangement suitable for
table mounting.
1. MI Voltmeter 96 x 96 mm Sq 0-300V 1 No.
2. MI Voltmeter 96 x 96 mm Sq 0-30V 1 No.
3. MI Ammeter 96 x 96 mm Sq 0-10A 1 No.
4. MI Ammeter 96 x 96 mm Sq 0-1A 1 No.
5. Single Phase Single Element Dynamo type
Wattmeter 1 No.
2.5/5 Amp, 75/150/300V Portable UPF type
6. Single Phase Single Element Dynamo type
Wattmeter 1 No.
1/2 Amp, 75/150/300V Portable LPF type
7. Single Phase Variac Air Cooled 0-270V, 1No.
TO OBTAIN EFFICIENCY & REGULATION
OF A SINGLE PHASE TRANSFORMER BY
SUMPNER’S (BACK TO BACK) TEST
MACHINE REQUIRED FOR EXPERIMENT
2 Nos Single Phase Transformer2 KVA, 230/230V
with Tapings at 50% & 86.6% Naturally Air Cooled
Copper Double wound, Shell type. The transformer
will be housed in MS sheet box enclosure with
rubber footings. All the terminals of primary &
secondary shall be brought over to Bakelite sheet
fitted on top of the box through insulated terminals.
CONTROL PANEL FOR EXPERIMENT
Fitted on Engraved Bakelite sheet enclosed in
almirah type M S box with lock & handle
arrangement
Suitable for table mounting.
1. MI Voltmeter 96 x 96 mm 0-300V 1 No.
2. MI Voltmeter 96 x 96 mm 0-600V 1 No.
3. MI Voltmeter 96 x 96 mm 0-30V 1 No.
4. MI Ammeter 96 x 96 mm 0-5A 2 No.
5. Single Phase Single Element Dynamo type 1 No.
Wattmeter 2.5/5A, 75/150/300V
6. Single Phase Variac Air Cooled 0-270V, 1No.
8. Complete Setup For performing :-
To obtain 3-phase to 2-phase conversion by Scott
connection.
TO STUDY THREE PHASE TO TWO PHASE
CONVERSION OF 3 PHASE
TRANSFORMER BY SCOTT CONNECTION
MACHINE REQUIRED FOR EXPERIMENT
2 Nos Single Phase Transformer 2 KVA,230/230V
with Tapings at 50% & 86.6% Naturally Air Cooled
Copper Double wound, Shell type. The transformer
will be housed in MS sheet box enclosure with
rubber footings. All the terminals of primary &
secondary shall be brought over to Bakelite sheet
fitted on top of the box through insulated terminals.
CONTROL PANEL FOR EXPERIMENT
Fitted on Engraved Bakelite sheet enclosed in
almirah type M S box with lock & handle
arrangement suitable for table mounting.
1. MI Voltmeter 96 x 96 mm 0-300V 1 No.
2. MI Voltmeter 96 x 96 mm 0-600V 1 No.
3. MI Ammeter 96 x 96 mm 0-5A 5 No.
4. Three Phase Variac Air Cooled 0-270V, 1No
5. Electrical Load 5 KW, 230V with dual output
1 No.
portable trolley mounted with castor wheels
1
Total
KAMLA NEHRU INSTITUTE OF TECHNOLOGY
SULTNAPUR (U.P) -228118
TENDER DOCUMENT
(FOR MANYAWAR KASHI RAM ENGINEERING COLLEGE OF INFORMATION TECHNOLOGY AMBEDKARNAGAR)
Bidders Proforma
Tender Purchase and Commissioning of Equipments for Electrical Measurement lab of Electrical Engg Department
Name of the firm with full address and contact number
FOR Manyawar Kanshi Ram Engineering College of Information Technology Ambedkarnagar (Located on Akbarpur-Tanda Road at 700 mt from collectrate Ambedkarnagar)
Cost of Tender Document DD No: Amount: Bank: Date: Drawn on favour of Director KNIT payable at Sultanpur
Earnest Money Deposit DD No: Amount: Bank: Date: Drawn on favour of Director KNIT payable at Sultanpur
PAN/TIN/TAN No PAN: TIN: TAN: (Attach proof)
Original Equipment Manufacturers /Authorization Letter from O.E.M.
Attach proof
Turnover in the last three years
Attach proof
Details of Similar Work Executed during last Three years
Attach proof
Signature and Seal of Bidders
Department of Electrical Engineering
Package –MKR/EE/04 – Electrical Measurement LAB
Tender Cost: Rs. 200.00 EMD- Rs. 5300.00
Bill of Quantity for Electrical Measurement Lab:
Sr.
No.
Name of Equipment with Specifications Qty. Unit Cost Total Cost Remarks
1. Complete Setup For performing :-
Calibration of ac voltmeter and ac ammeter
Apparatus required :- 1. Portable M.I. Voltmeter (for calibration) 0-
250 V - 1 No.
2. Portable M.I. Voltmeter (Standard) 0-300 V
- 1 No.
3. Single Phase Variac 0-6 A - 1 No.
4. M.I. Ammeter (for calibration) 0-2.5 A - 1
No.
5. Portable M.I. Ammeter (Standard) 0-10 A -
1 No.
6. Lamp Bank Load
02
2. Complete Setup For performing :-
Measurement of form factor of a rectified sine wave
and determine source of error if r.m.s. value is
measured by a multi-meter
02
3. Complete Setup For performing :-
Measurement of phase difference and frequency of a
sinusoidal ac voltage using C.R.O.
02
4. Complete Setup For performing :-
Measurement of power and power factor of a single
phase inductive load and to study effect of
capacitance connected across the load on the power
factor
Apparatus required :- 1. M.I. Voltmeter 0-300 V - 1 No.
2. M.I. Ammeter 0-5 A - 2 Nos.
3. M.I. Ammeter 0-10 A - 1 No.
4. Single Phase Inductive Load (Choke Coil)
0-6A - 1 No
5. Single Phase Variac 0-8 A - 1 No.
6. Wire wound Rheostat 5 A, 45 Ohms - 1 No.
02
5. Complete Setup For performing :-
Measurement of low resistance by Kelvin’s double
bridge
02
6. Complete Setup For performing :-
Measurement of voltage, current and resistance using
dc potentiometer
02
7. Complete Setup For performing :-
Measurement of inductance by Maxwell’s bridge
02
8. Complete Setup For performing :-
Measurement of inductance by Hay’s bridge 02
9. Complete Setup For performing :-
Measurement of inductance by Anderson’s bridge
02
10. Complete Setup For performing :-
Measurement of capacitance by Owen’s bridge
02
11. Complete Setup For performing :-
Measurement of capacitance by De Sauty bridge
02
12. Complete Setup For performing :-
Measurement of capacitance by Schering bridge
02
13. Complete Setup For performing :-
Study of Frequency and differential time counter 02
14. C.R.O. up to 30 Mhz 02
Total
KAMLA NEHRU INSTITUTE OF TECHNOLOGY SULTNAPUR (U.P) -228118
TENDER DOCUMENT
(FOR MANYAWAR KASHI RAM ENGINEERING COLLEGE OF INFORMATION TECHNOLOGY AMBEDKARNAGAR)
Bidders Proforma
Tender Purchase and Commissioning of Equipments for Electromechanical Energy Conversion lab-II of Electrical Engg Department
Name of the firm with full address and contact number
FOR Manyawar Kanshi Ram Engineering College of Information Technology Ambedkarnagar (Located on Akbarpur-Tanda Road at 700 mt from collectrate Ambedkarnagar)
Cost of Tender Document DD No: Amount: Bank: Date: Drawn on favour of Director KNIT payable at Sultanpur
Earnest Money Deposit DD No: Amount: Bank: Date: Drawn on favour of Director KNIT payable at Sultanpur
PAN/TIN/TAN No PAN: TIN: TAN: (Attach proof)
Original Equipment Manufacturers /Authorization Letter from O.E.M.
Attach proof
Turnover in the last three years
Attach proof
Details of Similar Work Executed during last Three years
Attach proof
Signature and Seal of Bidders
Department of Electrical Engineering
Package –MKR/EE/05 - ELECTROMECHANICAL ENERGY CONVERSION LAB – II
Tender Cost: Rs. 200.00 EMD- Rs. 8500.00
Bill of Quantity for Electromechanical Energy Conversion Lab-II:
Sr.
No.
Name of Equipment with Specifications Qty. Unit Cost Total Cost Remarks
1. Complete Setup For performing :-
1. To perform no load and blocked rotor tests on a
three phase squirrel cage induction motor and
determine equivalent circuit.
2. To perform load test on a three phase induction
motor and draw.
3. Torque -speed characteristics.
4. Power factor-line current characteristics.
5. To study speed control of three phase induction
motor by Keeping V/f ratio constant
Three Phase Induction Motor Trainer :-
Main Supply :Three Phase
415 V ±10%,50Hz
Motor´s Specification
Type : Squirrel Cage
Rating : 1HP
RPM :1440 (No Load)
Tachometer :20,000 RPM
With
All Measuring instruments required as per
Experiment
(Fitted on Engraved Bakelite sheet enclosed in
almirah type M S box with lock & handle
arrangement suitable for table mounting.)
1
2. Complete Setup For performing: - To perform no
load and blocked rotor tests on a single phase
induction motor and determine equivalent circuit.
Single Phase Induction Motor Trainer :-
Induction Motor
Type :Capacitor
Phase : Single
Current Type : AC
Rating :1 HP
Voltage rating : 230 V ±10%,50Hz
MCB :10A
Tachometer :20,000 RPM
Mains Supply : 230 V ±10%,50Hz
With
All Measuring instruments required as per
Experiment
(Fitted on Engraved Bakelite sheet enclosed in
almirah type ms box with lock & handle arrangement
suitable for table mounting.)
1
3. Complete Setup For performing :-
To study speed control of three phase induction motor
by varying supply voltage
Three Phase Variac (0-440 V ±10%,50Hz)
With Voltmeter and Ammeter
1
Motor´s Specification Type : 3-ΦSquirrel Cage
Rating : 1HP
RPM :1440 (No Load)
Tachometer :20,000 RPM
With
All Measuring instruments required as per
Experiment
(Fitted on Engraved Bakelite sheet enclosed in
almirah type M S box with lock & handle
arrangement suitable for table mounting.)
4. Complete Setup For performing :- To perform open circuit and short circuit tests on a
three phase alternator and determine voltage
regulation at full load and at unity, 0.8 lagging and
leading power factors by (i) EMF method (ii) MMF
method.
Three Phase Synchronous Generator Trainer :-
Input Supply :200 V Fixed DC
0-200 V Variable DC
Machine Specification (2 Nos.)
Both the Machine are flexibly coupled and
mounted on a M.S. channel base
DC Machine acts as a Prime Mover
Type : DC Shunt
Rating : 2 HP
Voltage Rating : 200 Volt
RPM : 1500 (No Load)
Insulation : Class B
Three Phase Synchronous Motor act as Generator
Type :Salient Pole Motor
Current type :AC
Rating :3 HP
Excitation Voltage :120 V
Voltage rating : 415 V ±10%
With
All Measuring instruments required as per
Experiment
(Fitted on Engraved Bakelite sheet enclosed in
almirah type M S box with lock & handle
arrangement suitable for table mounting.)
1
5. Complete Setup For performing :- To determine V-curves and inverted V-curves of a
three phase synchronous motor.
Three Phase Synchronous Generator Trainer :-
Input Supply : Three
Phase 415 ±10%,50 Hz
Machine Specification (2 Nos.)
Both the Machine are flexibly coupled and
mounted on a M.S. channel base
Three Phase Synchronous Motor
Type :Salient Pole Motor
Current type :AC
Rating :3 HP
Excitation Voltage :120 V
Voltage rating : 415 V ±10%
DC Machine
1
Type : DC Shunt
Rating : 2 HP
Voltage Rating : 200 Volt
RPM : 1500 (No Load)
Insulation : Class B
With
All Measuring instruments required as per
Experiment
(Fitted on Engraved Bakelite sheet enclosed in
almirah type M S box with lock & handle
arrangement suitable for table mounting.)
6. Complete Setup For performing :- To determine Xd and Xq of a three phase salient pole
synchronous machine using the slip test and draw the
power-angle curve.
Three Phase Synchronous Machine
Type :Salient Pole Motor
Current type :AC
Rating :3 HP
Voltage rating : 415 V ±10%
With
All Measuring instruments required as per
Experiment
(Fitted on Engraved Bakelite sheet enclosed in
almirah type M S box with lock & handle
arrangement suitable for table mounting.)
1
Total
KAMLA NEHRU INSTITUTE OF TECHNOLOGY SULTNAPUR (U.P) -228118
TENDER DOCUMENT
(FOR MANYAWAR KASHI RAM ENGINEERING COLLEGE OF INFORMATION TECHNOLOGY AMBEDKARNAGAR)
Bidders Proforma
Tender Purchase and Commissioning of Equipments for Network lab of Electrical Engg Department
Name of the firm with full address and contact number
FOR Manyawar Kanshi Ram Engineering College of Information Technology Ambedkarnagar (Located on Akbarpur-Tanda Road at 700 mt from collectrate Ambedkarnagar)
Cost of Tender Document DD No: Amount: Bank: Date: Drawn on favour of Director KNIT payable at Sultanpur
Earnest Money Deposit DD No: Amount: Bank: Date: Drawn on favour of Director KNIT payable at Sultanpur
PAN/TIN/TAN No PAN: TIN: TAN: (Attach proof)
Original Equipment Manufacturers /Authorization Letter from O.E.M.
Attach proof
Turnover in the last three years
Attach proof
Details of Similar Work Executed during last Three years
Attach proof
Signature and Seal of Bidders
Department of Electrical Engineering
Package –MKR/EE/06 - Network LAB
Tender Cost: Rs. 200.00 EMD- Rs. 2920.00
Bill of Quantity for Network Lab:
Sr.
No.
Name of Equipment with Specifications Qty. Unit Cost Total Cost Remarks
1. Complete Setup For performing :- Verification of principle of superposition with dc
and ac sources.
1. Experimental kit fitted with :-
(a) Bread Board – 01
(b) Voltage Source – 02
(c) Current Source – 01
2. Instrument Module OR Multimeters
3. Carbon Resistances :-
(a) 1 K – 05
(b) 2 K – 05
(c) 5 K – 05
(d) 10 K – 05
4. Patch Cords
02
2. Complete Setup For performing :- Verification of Thevenin, Norton and Maximum
power transfer theorems in ac circuits
(i) Variable AC Voltage Source – 2 Nos.
(ii) Variable AC Current Source – 1 No.
(iii) Inductors – 2 Nos.
(iv) Capacitors – 6 Nos.
(v) Fixed Resistances – 8 Nos.
(vi) Variable Resistance – 2 Nos.
(vii) Digital Multimeters
02
3. Complete Setup For performing :- Verification of Tellegin’s theorem for two networks
of the same topology
02
4. Complete Setup For performing :- Determination of transient response of current in
RL and RC circuits with step voltage input
(i) DC Voltage Source
(ii) Resistances – 5 Nos.
(iii) Capacitances – 3 Nos.
(iv) Inductors – 2 Nos.
02
5. Complete Setup For performing :- Determination of transient response of current in
RLC circuit with step voltage input for underdamp,
critically damp and overdamp cases
(i) DC Voltage Source
(ii) Resistances – 5 Nos.
(iii) Capacitances – 3 Nos.
(iv) Inductors – 2 Nos.
02
6. Complete Setup For performing :- Determination of frequency response of current in
RLC circuit with sinusoidal ac input
(i) DC Voltage Source
(ii) Resistances – 5 Nos.
(iii) Capacitances – 3 Nos.
(iv) Inductors – 2 Nos.
(v) AF Oscillator 1 KHz
02
7. Complete Setup For performing :- Determination of z and h parameters (dc only) for a
network and computation of Y and ABCD
parameters
02
8. Complete Setup For performing :- Determination of driving point and transfer
functions of a two port ladder network and verify
with
theoretical values
02
9. Complete Setup For performing :- Determination of image impedance and
characteristic impedance of T and Π networks,
using O.C. and S.C. tests Write Demo for the
following (in MS-Power point)
02
10. Complete Setup For performing :- Verification of parameter properties in inter-
connected two port networks: series, parallel and
cascade also study loading effect in cascade.
02
11. Complete Setup For performing :- Determination of frequency response of a Twin – T
notch filter. (i) AF Signal Generator 1 KHz
(ii) Resistances - 10 Nos
(iii) Capacitances – 10 Nos.
02
12. Complete Setup For performing :- To determine attenuation characteristics of a low
pass / high pass active filters.
02
Total
KAMLA NEHRU INSTITUTE OF TECHNOLOGY SULTNAPUR (U.P) -228118
TENDER DOCUMENT
(FOR MANYAWAR KASHI RAM ENGINEERING COLLEGE OF INFORMATION TECHNOLOGY AMBEDKARNAGAR)
Bidders Proforma
Tender Purchase and Commissioning of Equipments for Electrical Instrumentation lab of Electrical Engg Department
Name of the firm with full address and contact number
FOR Manyawar Kanshi Ram Engineering College of Information Technology Ambedkarnagar (Located on Akbarpur-Tanda Road at 700 mt from collectrate Ambedkarnagar)
Cost of Tender Document DD No: Amount: Bank: Date: Drawn on favour of Director KNIT payable at Sultanpur
Earnest Money Deposit DD No: Amount: Bank: Date: Drawn on favour of Director KNIT payable at Sultanpur
PAN/TIN/TAN No PAN: TIN: TAN: (Attach proof)
Original Equipment Manufacturers /Authorization Letter from O.E.M.
Attach proof
Turnover in the last three years
Attach proof
Details of Similar Work Executed during last Three years
Attach proof
Signature and Seal of Bidders
Department of Electrical Engineering
Package –MKR/EE/07 – Electrical Instrumentation Lab
Tender Cost: Rs. 200.00 EMD- Rs. 5620.00
Bill of Quantity for Electrical Instrumentation Lab
Sr.
No.
Name of Equipment with Specifications Qty. Unit Cost Total Cost Remarks
1. Complete Setup For performing :- Measurement of displacement using LVDT.
02
2. Complete Setup For performing :- Measurement of displacement using strain gauge
based displacement transducer.
02
3. Complete Setup For performing :- Measurement of displacement using magnetic
pickup.
02
4. Complete Setup For performing :- Measurement of load using strain gauge based load
cell.
02
5. Complete Setup For performing :- Measurement of water level using strain gauge
based water level transducer
02
6. Complete Setup For performing :- Measurement of flow rate by anemometer
02
7. Complete Setup For performing :- Measurement of temperature by RTD.
02
8. Complete Setup For performing :- Measurement of temperature by thermocouple
02
9. Complete Setup For performing :- Study of P,PI and PID controllers
02
10. Complete Setup For performing :- Study of storage oscilloscope and determination of
transient response of RLC circuit.
02
11. Complete Setup For performing :- Determination of characteristics of a solid state
sensor/fiber-optic sensor
02
12. Complete Setup For performing :- Design and test a signal conditioning circuit for any
transducer
02
Total
KAMLA NEHRU INSTITUTE OF TECHNOLOGY SULTNAPUR (U.P) -228118
TENDER DOCUMENT
(FOR MANYAWAR KASHI RAM ENGINEERING COLLEGE OF INFORMATION TECHNOLOGY AMBEDKARNAGAR)
Bidders Proforma
Tender Purchase and Commissioning of Equipments for Electronics Lab of Electrical Engg Department
Name of the firm with full address and contact number
FOR Manyawar Kanshi Ram Engineering College of Information Technology Ambedkarnagar (Located on Akbarpur-Tanda Road at 700 mt from collectrate Ambedkarnagar)
Cost of Tender Document DD No: Amount: Bank: Date: Drawn on favour of Director KNIT payable at Sultanpur
Earnest Money Deposit DD No: Amount: Bank: Date: Drawn on favour of Director KNIT payable at Sultanpur
PAN/TIN/TAN No PAN: TIN: TAN: (Attach proof)
Original Equipment Manufacturers /Authorization Letter from O.E.M.
Attach proof
Turnover in the last three years
Attach proof
Details of Similar Work Executed during last Three years
Attach proof
Signature and Seal of Bidders
Department of Electrical Engineering
Package –MKR/EE/08 – Electronics Lab
Tender Cost: Rs. 200.00 EMD- Rs. 2240.00
Bill of Quantity for Electronics Lab
Sr.
No.
Name of Equipment
(Experiment Setup/Kit)
Qty. Unit Cost Total Cost Remarks
1. Complete Setup For performing :-
To Plot V-I characteristics of junction diode and
zener diode.
02
2. Complete Setup For performing :-
To draw wave shape of the electrical signal at
input and output points of the half wave, full wave
and bridge rectifiers.
02
3. Complete Setup For performing :-
To Plot input / output characteristics for common
base transistor.
02
4. Complete Setup For performing :-
To Plot input /output characteristics of FET and
determine FET parameters at a given operating
point
02
5. Complete Setup For performing :-
To determine voltage gain, current gain, input
impedance and output impedance of common
emitter amplifier
02
6. Complete Setup For performing :-
To determine voltage gain, current gain, input
impedance and output impedance and frequency
response of R-C coupled common emitter
amplifier.
02
7. Complete Setup For performing :-
To design R-C Phase shift / Wein Bridge
oscillator and verify experimentally the frequency
of oscillation.
02
8. Complete Setup For performing :-
To study transistor as a switch and determine
load voltage and load current when the transistor
is ON.
02
Total
KAMLA NEHRU INSTITUTE OF TECHNOLOGY
SULTNAPUR (U.P) -228118
TENDER DOCUMENT
(FOR MANYAWAR KASHI RAM ENGINEERING COLLEGE OF INFORMATION TECHNOLOGY AMBEDKARNAGAR)
Bidders Proforma
Tender Purchase and Commissioning of Equipments for Power Electronics Lab of Electrical Engg Department
Name of the firm with full address and contact number
FOR Manyawar Kanshi Ram Engineering College of Information Technology Ambedkarnagar (Located on Akbarpur-Tanda Road at 700 mt from collectrate Ambedkarnagar)
Cost of Tender Document DD No: Amount: Bank: Date: Drawn on favour of Director KNIT payable at Sultanpur
Earnest Money Deposit DD No: Amount: Bank: Date: Drawn on favour of Director KNIT payable at Sultanpur
PAN/TIN/TAN No PAN: TIN: TAN: (Attach proof)
Original Equipment Manufacturers /Authorization Letter from O.E.M.
Attach proof
Turnover in the last three years
Attach proof
Details of Similar Work Executed during last Three years
Attach proof
Signature and Seal of Bidders
Department of Electrical Engineering
Package –MKR/EE/09 – Power Electronics Lab
Tender Cost: Rs. 200.00 EMD- Rs. 5360.00
Bill of Quantity for Power Electronics Lab
Sr.
No.
Name of Equipment Qty. Unit Cost Total Cost Remarks
1. Complete Setup For performing :- To study V-I characteristics of SCR and
measure latching and holding currents. Complete setup with digital measuring
instruments.
Demonstration board with following
facilities :-
(a) Isolated 0-230 V DC variable source –
1 Set
(b) Isolated 0-600 V DC variable source –
1 Set
(c) Isolated 0-12 V DC variable source –
2 Sets
(d) External Load – 3 Nos.
(e) SCR
Multimeter
Lamp 15 Watt 230 V – 2 Nos.
Patch Cords.
Demonstration Board Cover.
To conduct SCR Shorted gate
experiment
To conduct biased (Forward &
Reverse) gate SCR firing experiments
Set of Patch Chords & Manual.
02
2. Complete Setup For performing :- To study UJT trigger circuit for half wave and
full wave control.
Setup will consists of :-
Demonstration Board with following
facilities :-
(a) Isolated AC 230 V & 14 V Supply
(b) 10:1 Resistive Attenuator for
observation on CRO.
(c) Fuse for short circuit protection.
25 Watt 250 V Lamp.
Demonstration Board Cover
02
Triggering circuits
Set of Patch Chords & Manual
3. Complete Setup For performing :- To study single-phase half wave controlled
rectified with (i) resistive load (ii) inductive load
with and without freewheeling diode.
The setup is provided with isolation
transformer for C.R.O. protections and
lamp bank.
1. Demonstration Board with following
facilities :-
(a) Single Phase Half Controlled Bridge
(b) Firing Pulse Generator
(c) Resistive Load (Lamp)
(d) Inductive Load (Choke)
(e) Voltmeter 0-300V
(f) Ammeter 0-5A
(g) 1:10 Attenuator for CRO
(h) Isolated 220 V AC for CRO
2. DC Motor 1 HP
3. Connecting Leads
4. Lamp Holder
5. Lamp 250 Volts
Complete experimental setup with DC Motor & Engraved Panel board with Banana Sockets for ease of connections by students
01
4. Complete Setup For performing :- To study single phase (i) fully controlled (ii) half
controlled bridge rectifiers with resistive and
Inductive loads.
Features :-
230V, AC Isolated Transformer,
Power 50 Watt
9V DC at 100 mA Zener Regulated
Power Supply
Two UJT.
Two Pulse Transformer1:1:1.
Two Potentiometers for controlling
UJT firing angle.
Bulb 40W, 230 AC
Adequate no of others Electronics
Components.
02
5. Complete Setup For performing :- To study three-phase fully/half controlled bridge
rectifier with resistive and inductive loads.
Features :-
01
Three Phase line commuted fully-
controlled thyristorized bridge converter.
Miniature Circuit Breaker (MCB).
Three cards consisting of Zero
Crossing Detector, Integrator, Comparator
and Pulse Generator one for each phase,
for controlling thyristors. Another card in
conjunction with above three cards for
controlling the triggering angles of the
negative group of three thyristors.
Firing angle control potentiometer.
415:50V transformer for rectification
and low voltage AC supply for triggering.
12V at 500mA, power supply for
triggering circuit.
Six nos. Driver Circuits with Pulse
Transformer.
R & L load with Load voltage divider.
Panel meter for measurement of
voltage & current.
One freewheel diode.
Unearthed mains sockets for CRO.
6. Complete Setup For performing :- To study single-phase ac voltage regulator with
resistive and inductive loads.
Complete setup with fraction Horse
Power Motor.
AC Phase Control training unit with
following facilities :-
(a) Isolated 230 V or 50 V supply
(b) Fuse for Short Circuit protection
(c) AC Phase control by RC Triggering
(d) AC Phase Control by UJT Triggering
(e) 10:1 Potential Divider for CRO
Protection Cover - 1 No.
Lamp 25 Watt, 230 V - 1 No.
Set of Patch Chords & Manual.
Complete setup with Motor
02
7. Complete Setup For performing :- To study single phase cyclo-converter
The experimental setup consists of :-
(i) Power Circuit consisting of two fully
controlled Bridge Converter connected in
anti parallel (Bridges P & N). Bridge P
01
supplies load current in the positive half
of output cycle and bridge N provides
load current in the negative half of output
cycle.
(ii) Firing Circuit consists of Micro
Controller Based Firing Unit which
provides Isolated Gate pulses through
pulse transformers separately for P & N
Bridges. Toggle switch is provided to
select the output frequency (1/1f, 1/2f,
1/3f, 1/4f, 1/5f). Firing angle can be
changed either :-
a) through toggle switches for increasing
and decreasing of firing angle. Firing
angle during all half cycles of AC input
supply remains same in this mode of
control.
b) through serial port of computer by
connector provided on the experimental
kit to the serial port of computer and then
entering the firing angle to the key board.
In this mode of control the firing angle of
each half cycle of input supply can be
independently controlled.
(iii) Patch Cord.
(iv) Instruction Manual 8. Complete Setup For performing :-
To study triggering of (i) IGBT (ii) MOSFET
(iii) power transistor
1. Complete experimental setup
consisting demonstration Board with
following facilities :-
(a) 110 V DC Supply
(b) Different testing points
(c) 1:10 Attenuator for CRO
(d) Triggering Generator
(e) IGBT, Mosfet & Power Transistor
2. Lamp 15 Watt 250V
3. Connecting Leads
02
9. Complete Setup For performing :- To study operation of IGBT/MOSFET chopper
circuit
This is DC chopper circuit for getting a
variable DC voltage by using on time
control and frequency control to feed DC
(Universal Motor). Circuit demonstrate
the use of smooth speed variation with the
help of chopper circuit and test points are
provided.
1. Demonstration Board with following
facilities :-
(a) 110 V DC Supply
01
(b) Different testing points
(c) 1:10 Attenuator for CRO
(d) DC Voltmeter
(e) DC Amp Meter
2. Lamp 60 Watt 250V
3. Connecting Leads
10. Complete Setup For performing :- To study MOSFET/IGBT based single-phase
series-resonant inverter.
Complete experimental setup consisting
of :-
1. Demonstration Board with following
facilities :-
(a) Isolated DC 110 V
(b) Isolated Gate Frequency
(c) External Load
(d) 200 W Lamp for Short Circuit
Protection
(e) 1:10 Resistive Attenuator
(f) 1A Fuse for short circuit protection.
2. Demonstration Board Cover
3. Patch Cords
All the circuit diagram and necessary test
point are clearly marked on Engraved
front panel for education study purpose.
01
11. Complete Setup For performing :- To study MOSFET/IGBT based single-phase
bridge inverter.
Consisting of :-
1. Demonstration Board with following
facilities :-
(a) Isolated DC 110 V.
(b) Isolated Gate Frequency
(c) External Load
(d) 200 W Lamp for Short Circuit
Protection
(e) 1:10 Resistive Attenuator
(f) 1A Fuse for short circuit protection.
2. Demonstration Board Cover
3. Patch Cords
All the circuit diagram and necessary test
point are clearly marked on Engraved
front panel for education study purpose.
Supplied
01
Total
KAMLA NEHRU INSTITUTE OF TECHNOLOGY SULTNAPUR (U.P) -228118
TENDER DOCUMENT
(FOR MANYAWAR KASHI RAM ENGINEERING COLLEGE OF INFORMATION TECHNOLOGY AMBEDKARNAGAR)
Bidders Proforma
Tender Purchase and Commissioning of Equipments for Control System Lab of Electrical Engg Department
Name of the firm with full address and contact number
FOR Manyawar Kanshi Ram Engineering College of Information Technology Ambedkarnagar (Located on Akbarpur-Tanda Road at 700 mt from collectrate Ambedkarnagar)
Cost of Tender Document DD No: Amount: Bank: Date: Drawn on favour of Director KNIT payable at Sultanpur
Earnest Money Deposit DD No: Amount: Bank: Date: Drawn on favour of Director KNIT payable at Sultanpur
PAN/TIN/TAN No PAN: TIN: TAN: (Attach proof)
Original Equipment Manufacturers /Authorization Letter from O.E.M.
Attach proof
Turnover in the last three years
Attach proof
Details of Similar Work Executed during last Three years
Attach proof
Signature and Seal of Bidders
Department of Electrical Engineering
Package –MKR/EE/10 – Control System Lab
Tender Cost: Rs. 200.00 EMD- Rs. 6280.00
Bill of Quantity for Control System Lab:
Sr.
No.
Name of Equipment Qty. Unit Cost Total Cost Remarks
1. Complete Setup For performing :- To determine response of first order and
second order systems for step input for
various values of constant ’K’ using linear
simulator unit and compare theoretical and
practical results.
Simulated blocks – configurable
as 1st
, 2nd
and 3rd
order systems with
negative feedback.
Forward gain adjustable
through a calibrated 10 turn
potentiometer (Resolution 1 in
1000)
Three built-in signal sources
Square wave : 1 V p-p (min)
Triangular wave : + 0.5 V p-p
(min)
Trigger pulses : + 10 V (min)
Frequency adjustable : 40 Hz
– 90 Hz
Provision for disturbance
inputs at input and load
I.C. regulation in all internal
power supplies.
Power requirement less than
10W at 220 V, 50 Hz operation
Supporting literature and
patch cords included.
Except a CRO no other
equipment is required.
02
2. Complete Setup For performing :- To study P, PI and PID temperature
controller for an oven and compare their
performance.
Temperature controller with
facilities for P, I, D and relay
control blocks.
Operating temperature:
ambient to 90O
C.
02
Separate controls for P.I.D
channel gains.
Two settings for relay
hysterisis.
Fast 25 W oven fitted with IC
temperature sensor.
Digital display of set and
measured temperature on a 3½
digit built in DVM.
Buffered output for recorder
IC regulation in controller
circuit power supplies.
220V, 50 Hz mains operated.
Supporting literature and
patch cords included.
No accessories are required.
3. Complete Setup For performing :- To study and calibrate temperature using
resistance temperature detector (RTD)
Using Temperature sensor : RTD PT
100
1. Range: 0 to 200 degree centigrade.
2. Mode of control: on/off.
3. Relay: O/E/N make 5 Amp rating.
4. Optional : Recorder.
5. Set up comes with digital temp.
indication, set point indication,
set point control and
calibration check up for 0
degree and 100 degree
centigrade.
Model size: 192 x 96 x 300
mm with powder coated M.S.
box having neatly labeled
anodised plate.
6. Accuracy of induction: +/- 1% of
the full range.
Complete set up with model process heated with comptalux bulbs. A detailed manual.
02
4. Complete Setup For performing :- To design Lag, Lead and Lag-Lead
compensators using Bode plot.
Simulated uncompensated system
having adjustable damping
peak percent overshoot Mp
variable from 20% to 50% and
steady state error variable from
02
50% to 0.5%.
• Compensation network
implementation through built-in
variable gain amplifier. Gain is
adjustable from 1 to 11.
• Built-in square and sine wave
generators for transient and
frequency response studies.
Frequency adjustable from
25Hz – 800Hz (approx.)
• 220V + 10% 50 Hz mains
operation.
5. Complete Setup For performing :- To study DC position control system
1. 5k ohm +/- 1% linearity, Precision
servo Potentiometers having
bearing used as error detector.
2. Output potentiometer, similar as
input potentiometer to convert
output position into a voltage
signal.
3. Summing Amplifier with adjustable
gain.
4. Armature controlled D.C.
servomotor with suitable
coupling required for (i)
output position indicator and
load. (ii) Tachogenerator.
5. D.C. tachogenerator coupled to
D.C. motor, for derivative
feedback.
6. Preamplifier and power amplifier to
drive the D.C. motor on the
basis of the error signal. D.C.
motor is 12 volt, lamp,
permanent, magnet a with gear
train.
7. Power supply for, armature winding
and electronic amplifier.
Suitable test points brought on
the side panel.
8. A detailed instruction manual will
be supplied.
02
6. Complete Setup For performing :- To study synchro-transmitter and receiver
and obtain output V/S input characteristics
02
7. Complete Setup For performing :- To determine speed-torque characteristics
of an ac servomotor.
1. Two phase servomotor.
02
2. The speed measuring device which
will not load the motor. A
photoelectric pick up using disc
with 20 holds and a phototransistor
are used for speed sensing.
Calibration source at 100 Hz is
used for RPM indicator.
3. Loading arrangement for
servomotor.
4. Torque measuring device.
5. A detailed manual.
6. RPM indicator and ammeter
measuring load current.
7. Unit will be covered by an acrylic
sheet to facilitate clear view of the
entire system 8. Complete Setup For performing :-
To study performance of servo voltage
stabilizer at various loads using load bank.
1. Demonstration unit with
following facilities :-
(a) Variable Input AC Supply
(b) AC Servo Motor
(c) Servo Amplifier &
Controller (d) 0-300 Voltmeter
(e) Auto and Non-auto
provision
(f) Manual Up & Down
2. 100 Watt 250 V Lamp: Qty – 05.
3. Capacity of stabilizer 1 KVA.
02
9. Complete Setup For performing :- To study behavior of separately excited dc
motor in open loop and closed loop
conditions at various loads.
1. Potentiometer as input
transducer for converting
reference voltage. It will
be suitably marked.
2. A DC Tacho-generator/speed
sensor will be also used to
indicate the motor speed in
RPM.
3. Summing amplifier to receive
inputs, reference signal
and tachgenerator output.
This amplifier will have an
adjustable again.
4. Separately excited DC Motor
rated for 1500 RPM 1 HP
at 220 volts with loading
arrangement.
02
5. Thyristor converter using single
phase half controlled
converter to control DC
motor through armature
and power supply for field
winding and electronic
amplifier.
6. The unit will be supplied
alongwith instruction
manual.
7. The entire system will, for the
range 300 RPM to 1000
RPM work as a closed
loop control system.
8. Suitable protection for the
electronic circuits and
motor.
10. Complete Setup For performing :- To study PID Controller for simulation
proves like transportation lag.
Simulated block-dead time
(transportation leg), integrator,
Time constants, error detector
and gain.
PID Controller (configurable as P,
PI, PD or PID)
Proportional Band : 5% to 50%
(Gain 2-20)
Integral Time : 10 ms – 100 ms
Derivative time : 2-20 ms
Built in IC regulated power
supply.
Built in 3½ digit DVM
Built in signal sources.
Set value : -1V to + 1V
Square wave 1 V p-p (min) at 40
Hz (typical)
Triangular wave : 1 V p-p (min)
at 40 Hz (typical)
Detailed literature and patch
chords included
220 V, 50 Hz mains operations
Essential accessory : a CRO
02
Total
KAMLA NEHRU INSTITUTE OF TECHNOLOGY SULTNAPUR (U.P) -228118
TENDER DOCUMENT
(FOR MANYAWAR KASHI RAM ENGINEERING COLLEGE OF INFORMATION TECHNOLOGY AMBEDKARNAGAR)
Bidders Proforma
Tender Purchase and Commissioning of Equipments for Microprocessor lab of Electrical Engg Department
Name of the firm with full address and contact number
FOR Manyawar Kanshi Ram Engineering College of Information Technology Ambedkarnagar (Located on Akbarpur-Tanda Road at 700 mt from collectrate Ambedkarnagar)
Cost of Tender Document DD No: Amount: Bank: Date: Drawn on favour of Director KNIT payable at Sultanpur
Earnest Money Deposit DD No: Amount: Bank: Date: Drawn on favour of Director KNIT payable at Sultanpur
PAN/TIN/TAN No PAN: TIN: TAN: (Attach proof)
Original Equipment Manufacturers /Authorization Letter from O.E.M.
Attach proof
Turnover in the last three years
Attach proof
Details of Similar Work Executed during last Three years
Attach proof
Signature and Seal of Bidders
Department of Electrical Engineering
Package –MKR/EE/11 – Microprocessor Lab
Tender Cost: Rs. 200.00 EMD- Rs. 3420.00
Bill of Quantity for Microprocessor Laboratory:
Sr.
No.
Name of Equipment Qty. Unit Cost Total Cost Remarks
1. Complete Setup For performing :- To study 8085 based microprocessor system
03
2. Complete Setup For performing :- To study 8086 and 8086A based
microprocessor system
03
3. Complete Setup For performing :- To study Pentium Processor
03
4. Interfacing kit of RAM
for interfacing based Experiment - To obtain
chip to 8085/8086 based system
03
5. Interfacing kit of keyboard controller
For interfacing based Experiment - To obtain
interfacing of keyboard controller
03
6. Interfacing kit of DMA controller
For interfacing based Experiment - To obtain
interfacing of DMA controller
03
7. Interfacing kit of PPI
For interfacing based Experiment - To obtain
interfacing of PPI
03
8. Interfacing kit of UART/USART
For interfacing based Experiment - To obtain
interfacing of UART/USART
02
9. Complete Setup For performing :- To perform microprocessor based stepper
motor operation through 8085 kit
02
10. Complete Setup For performing :- To perform microprocessor based traffic light
control
02
11. Complete Setup For performing :- To perform microprocessor based temperature
control of hot water.
02
Total
KAMLA NEHRU INSTITUTE OF TECHNOLOGY
SULTNAPUR (U.P) -228118
TENDER DOCUMENT
(FOR MANYAWAR KASHI RAM ENGINEERING COLLEGE OF INFORMATION TECHNOLOGY AMBEDKARNAGAR)
Bidders Proforma
Tender Purchase and Commissioning of Equipments for Communication Engg. lab of Electrical Engg Department
Name of the firm with full address and contact number
FOR Manyawar Kanshi Ram Engineering College of Information Technology Ambedkarnagar (Located on Akbarpur-Tanda Road at 700 mt from collectrate Ambedkarnagar)
Cost of Tender Document DD No: Amount: Bank: Date: Drawn on favour of Director KNIT payable at Sultanpur
Earnest Money Deposit DD No: Amount: Bank: Date: Drawn on favour of Director KNIT payable at Sultanpur
PAN/TIN/TAN No PAN: TIN: TAN: (Attach proof)
Original Equipment Manufacturers /Authorization Letter from O.E.M.
Attach proof
Turnover in the last three years
Attach proof
Details of Similar Work Executed during last Three years
Attach proof
Signature and Seal of Bidders
Department of Electrical Engineering
Package –MKR/EE/12 – Communication Engineering Lab
Tender Cost: Rs. 200.00 EMD- Rs. 9640.00
Bill of Quantity for Communication Engineering Laboratory:
Sr.
No.
Name of Equipment Qty. Unit Cost Total Cost Remarks
1. Complete Setup For performing :- To study amplitude modulation using a
transistor and determine depth of modulation.
02
2. Complete Setup For performing :- To study generation of DSB-SC signal using
balanced modulator.
02
3. Complete Setup For performing :- To study generation of SSB signal
02
4. Complete Setup For performing :- To study envelop detector for demodulation of
AM signal and observe diagonal peak clipping
effect.
02
5. Complete Setup For performing :- To study super heterodyne AM receiver and
measurement of sensitivity, selectivity and
Fidelity.
02
6. Complete Setup For performing :- To study frequency modulation using voltage
controlled oscillator.
02
7. Complete Setup For performing :- To detect FM signal using Phase Locked Loop.
02
8. Complete Setup For performing :- To measure noise figure using a noise
generator.
02
9. Complete Setup For performing :- To study PAM, PWM and PPM.
02
10. Complete Setup For performing :- To study Delta Modulation and Adaptive Delta
Modulation.
02
11. Digital Storage Oscilloscope (DSO, Make
Scientech)
1-60Mhz
10
Total
KAMLA NEHRU INSTITUTE OF TECHNOLOGY SULTNAPUR (U.P) -228118
TENDER DOCUMENT
(FOR MANYAWAR KASHI RAM ENGINEERING COLLEGE OF INFORMATION TECHNOLOGY AMBEDKARNAGAR)
Bidders Proforma
Tender Purchase and Commissioning of Equipments for Power System lab of Electrical Engg Department
Name of the firm with full address and contact number
FOR Manyawar Kanshi Ram Engineering College of Information Technology Ambedkarnagar (Located on Akbarpur-Tanda Road at 700 mt from collectrate Ambedkarnagar)
Cost of Tender Document DD No: Amount: Bank: Date: Drawn on favour of Director KNIT payable at Sultanpur
Earnest Money Deposit DD No: Amount: Bank: Date: Drawn on favour of Director KNIT payable at Sultanpur
PAN/TIN/TAN No PAN: TIN: TAN: (Attach proof)
Original Equipment Manufacturers /Authorization Letter from O.E.M.
Attach proof
Turnover in the last three years
Attach proof
Details of Similar Work Executed during last Three years
Attach proof
Signature and Seal of Bidders
Department of Electrical Engineering
Package –MKR/EE/13 – Power System Lab
Tender Cost: Rs. 200.00 EMD- Rs. 13300.00
Bill of Quantity Power System Lab:
Sr.
No.
Name of Equipment Qty. Unit Cost Total Cost Remarks
1. Complete Setup For performing :- To determine negative and zero sequence
reactance of an alternator.
MACHINES REOUIRED
M G Set: DC SHUNT MOTOR/3 PHASE
ALTERNATOR SALIENT POLE TYPE
(ROTATING FIELD)
DC Motor
Type. DC Shunt wound, screen protected.
Horizontal foot mounted, with interpoles and
3 points DC Starter, having No volt and
overload release coils.
Capacity: 3HP
RPM : 1500 (controlled variation)
Volts : 230
Insulation : Class ‘B’
Cooling : Fan cooled
Connections: Shunt, all the terminals of
Armature and x field winding shall be brought
over to a Bakelite sheet fixed to C I terminal
fix fitted on top of Motor.
Alternator :
Type : Salient pole type (Rotating Field
type), 3 phase 4 wire screen protected,
horizontal foot mounted, fan cooled,
separately excited
Capacity : 2 KVA
RPM : 1500 for max output and frequency of
50 Hz
Volts : 415V
Insulation : Class ‘B’
Frequency : 50 Hz
Power factor : 0.8 p.f. lagging
Exciter
Type : Static type through Rectifier
With
All Measuring instruments required as per
Experiments
(Fitted on Engraved Bakelite sheet enclosed
in almirah type M S box with lock & handle
arrangement suitable for table mounting.)
01.
2. Complete Setup For performing :- To determine direct axis reactance (xd) and
quadrature axis reactance (xq) of a salient
pole alternator.
MACHINES REOUIRED
M G Set: DC SHUNT MOTOR/3 PHASE
ALTERNATOR SALIENT POLE TYPE
01.
(ROTATING FIELD)
DC Motor
Type. DC Shunt wound, screen protected.
Horizontal foot mounted, with interpoles and
3 points DC Starter, having No volt and
overload release coils.
Capacity : 3HP
RPM : 1500 (controlled variation)
Volts : 230
Insulation : Class ‘B’
Cooling : Fan cooled
Connections: Shunt, all the terminals of
Armature and x field winding shall be brought
over to a Bakelite sheet fixed to C I terminal
fix fitted on top of Motor.
Alternator :
Type : Salient pole type (Rotating Field
type), 3 ph 4 wire screen protected, horizontal
foot mounted, fan cooled, separately excited
Capacity : 2 KVA
RPM : 1500 for max output and
frequency of 50 Hz
Volts : 415V
Insulation : Class ‘B’
Frequency : 50 Hz
Power factor : 0.8 p.f. lagging
Connections : 3 phase 4 wire
Exciter
Type : D.C Shunt Generator or Rectifier,
220V, DC through slip rings.
With
All Measuring instruments required as per
Experiment
(Fitted on Engraved Bakelite sheet enclosed
in almirah type M S box with lock & handle
arrangement suitable for table mounting.)
Additional Accessories Required
3 Phase Variac, 0-470V,
3. Complete Setup For performing :- To determine sub transient direct axis
reactance (xd) and sub transient quadrature
axis reactance (xq) of an alternator
MACHINES REOUIRED
M G Set: DC SHUNT MOTOR/3 PHASE
ALTERNATOR SALIENT POLE TYPE
(ROTATING FIELD)
DC Motor
Type. DC Shunt wound, screen protected.
Horizontal foot mounted, with interpoles and
3 points DC Starter, having No volt and
overload release coils.
Capacity : 3HP
RPM : 1500 (controlled variation)
Volts : 230
Insulation : Class ‘B’
01.
Cooling : Fan cooled
Connections: Shunt, all the terminals of
Armature and x field winding shall be brought
over to a Bakelite sheet fixed to C I terminal
fix fitted on top of Motor.
Alternator :
Type : Salient pole type (Rotating Field type),
3 ph 4 wire screen protected, horizontal foot
mounted, fan cooled, separately excited with
connection brought out top of terminal plate
for each measurement of sub transient
reactance
Capacity : 2 KVA
RPM : 1500 for max output and
frequency of 50 Hz
Volts : 415V
Insulation : Class ‘B’
Frequency : 50 Hz
Power factor : 0.8 p.f. lagging
Exciter
Type: D.C Shunt Generator or Rectifier,
220V, DC through slip rings.
With
All Measuring instruments required as per
Experiment
(Fitted on Engraved Bakelite sheet enclosed
in almirah type M S box with lock & handle
arrangement suitable for table mounting.)
4. Complete Setup For performing :- To determine fault current for L-G, L-L, L-L-
G and L-L-L faults at the terminals of an
alternator at very low excitation
MACHINES REQUIRED :
M G Set : D C SHUNT MOTOR/3 PHASE
ALTERNATOR SALIENT POLE TYPE
(ROTATING FIELD)
DC Motor
Type. DC Shunt wound, screen protected.
Horizontal foot mounted, with interpoles and
3 points DC Starter, having No volt and
overload release coils.
Capacity : 3HP
RPM : 1500 (controlled variation)
Volts : 230
Insulation : Class ‘B’
Cooling : Fan cooled
Connections: Shunt, all the terminals of
Armature and x field winding shall be brought
over to a Bakelite sheet fixed to C I terminal
fix fitted on top of Motor.
Alternator :
01.
Type : Salient pole type (Rotating Field type),
3 ph 4 wire screen protected, horizontal foot
mounted, fan cooled, separately excited
Capacity : 2 KVA
RPM : 1500 for max output and
frequency of 50 Hz
Volts : 415V
Insulation : Class ‘B’
Frequency : 50 Hz
Power factor : 0.8 p.f. lagging
Connections : 3 phase 4 wire
Exciter Type : Static type through Rectifier
With
All Measuring instruments required as per
Experiment
(Fitted on Engraved Bakelite sheet enclosed
in almirah type M S box with lock & handle
arrangement suitable for table mounting.)
5. Complete Setup For performing :- To study the IDMT over current relay and
determine the time current characteristics
APPARATUS REQUIRED
1. Digital AC Voltmeter 0-300 V,
-1 No.
2. Digital AC Ammeter 0-10 A
-1 No.
3. Digital Time Totalizer
-1 No.
4. IDMT Relay ‘ALSTOM (AREVA)’/ABB
make -1No.
Type CDG-11 Electro Mechanical Type
(INVERSE)
5. 1 Ph Variac
- 1 No.
6. Loading CT
- 1 No.
7. Diode Type Rectifier Supply
-1 No.
8. Multipoint Relay
-1 No.
9. Push Button
- 2 No.
10. Indicating Light -
11. DP Isolator
12. Rotary Switch
All the accessories and Relays will be fitted
on sheet fixed to M.S. box cabinet almirah
type suitable for table mounting with
provision for lock and key arrangement.
01.
6. Complete Setup For performing :- To study percentage differential relay
APPARATUS REQUIRED
1. Percentage Differential Relays Static type
01.
‘ALSTOM (AREVA) make
-1.No.
2. Digital AC Ammeter 0-10 A
-2 No.
3. Digital Time Totalizer
-1 No.
4. DP Isolator
5. Push Button
- 2 No. 6. Loading CT
- 1 No.
7. Multipoint Relay with Transformer
-1No. & Rectifier
Supply
8. Rotary Switch
9. Isolation Transformer
-1No.
10. Tubular Rheostat for Differential Current
& Through Current
All the accessories and Relays will be fitted
on sheet fixed to M.S. box cabinet almirah
type suitable for table mounting with
provision of lock and key arrangement.
7. Complete Setup For performing :- To determine location of fault in a cable using
cable fault locator
APPARATUS REQUIRED
CABLE FAULT LOCATOR
Complete experimental setup consisting of
Rheostat, Galvanometer, Measuring Tape, 3
Core Cable, DC Power Source, Digital
Measuring Instrument
01.
8. Complete Setup For performing :- To study ferranty effect and voltage
distribution in H.V. long transmission line
using transmission line model.
APPARATUS REQUIRED
Complete Experimental setup as per
requirement of the Experiment, fitted in M S
sheet box complete with patch cords for inter
connection & Manual.
01.
9. Complete Setup For performing :- To study operation of oil testing set.
APPARATUS REQUIRED
Complete Experimental setup as per
requirement of the Experiment, with testing
kit and sample of oil.
01.
10. Complete Setup For performing :- To study Impedance, MHO and Reactance
type distance relays
APPARATUS REQUIRED
Complete Experimental setup as per
requirement of the Experiment, fitted in M S
sheet box complete with patch cords for inter
connection & Manual.
01.
Total
KAMLA NEHRU INSTITUTE OF TECHNOLOGY SULTNAPUR (U.P) -228118
TENDER DOCUMENT
(FOR MANYAWAR KASHI RAM ENGINEERING COLLEGE OF INFORMATION TECHNOLOGY AMBEDKARNAGAR)
Bidders Proforma
Tender Purchase and Commissioning of Equipments for Electric Drive lab of Electrical Engg Department
Name of the firm with full address and contact number
FOR Manyawar Kanshi Ram Engineering College of Information Technology Ambedkarnagar (Located on Akbarpur-Tanda Road at 700 mt from collectrate Ambedkarnagar)
Cost of Tender Document DD No: Amount: Bank: Date: Drawn on favour of Director KNIT payable at Sultanpur
Earnest Money Deposit DD No: Amount: Bank: Date: Drawn on favour of Director KNIT payable at Sultanpur
PAN/TIN/TAN No PAN: TIN: TAN: (Attach proof)
Original Equipment Manufacturers /Authorization Letter from O.E.M.
Attach proof
Turnover in the last three years
Attach proof
Details of Similar Work Executed during last Three years
Attach proof
Signature and Seal of Bidders
Department of Electrical Engineering
Package –MKR/EE/14 – Electric Drive Lab
Tender Cost: Rs. 200.00 EMD- Rs. 10780.00
Bill of Quantity for Electric Drives Lab:
Sr.
No.
Name of Equipment Qty. Unit Cost Total Cost Remarks
1. Complete Setup For performing :- To study speed control of separately
excited dc motor by varying armature
voltage using single-phase fully controlled
bridge converter.
1. Engraved Demonstration Board with
following facilities :-
(a) Single Phase Fully Controlled Bridge
(b) Firing Pulse Generator Digital type
(c) Resistive Load (Lamp) With & without
free wheeling Diode
(d) Inductive Load (Choke)
(e) Voltmeter 0-300V
(f) Ammeter 0-5A
(g) 1:10 Attenuator for CRO
(h) Isolated 220 V AC for CRO
2. DC Motor 1 HP
3. Connecting Leads
4. Lamp Holder
5. Lamp 250 Volts
Complete experimental setup with DC Motor Engraved Panel board with Banana Sockets for ease of connections by students
01
2. Complete Setup For performing :- To study speed control of separately
excited dc motor by varying armature
voltage using single phase half controlled
bridge converter.
Demonstration Board with following
facilities :-
(a) Single Phase Half Controlled Bridge
(b) Firing Pulse Generator
(c) Resistive Load (Lamp)
(d) Inductive Load (Choke)
(e) Voltmeter 0-300V
(f) Ammeter 0-5A
(g) 1:10 Attenuator for CRO
(h) Isolated 220 V AC for CRO
2. DC Motor 1 HP
3. Connecting Leads
4. Lamp Holder
5. Lamp 250 Volts
01
3. Complete Setup For performing :- To study speed control of separately
excited dc motor using single phase dual
converter (Static Ward-Leonard Control)
(i) Power Circuit consisting of two single
phase fully controlled Bridge Converter
01
connected in anti parallel.
(ii) Centre Tap Inductor required for
circulating mode operation of dual
converter.
(iii) Micro controlled based firing circuit
which generates firing pulses for both P
and N converters.
(iv) MCB, Voltmeter, Ammeter and Lamp
load
(v) Patch Cord & Instruction Manual
(vi) DC Motor 1 HP, 230V
4. Complete Setup For performing :- To study speed control of separately
excited dc motor using MOSFET/IGBT
chopper
1. Demonstration Board with following
facilities :-
(a) 110 V DC Supply
(b) Different testing points
(c) 1:10 Attenuator for CRO
(d) DC Voltmeter
(e) DC Amp Meter
2. Lamp 60 Watt 250V
3. Connecting Leads
01
5. Complete Setup For performing :- To study closed loop control of separately
excited dc motor
01
6. Complete Setup For performing :- To study speed control of single phase
induction motor using single phase ac
voltage controller
The experimental setup consisting of :-
(i) Micro Controller Kit with firing circuit.
(ii) Single Phase Induction Motor
Capacitor Run with Loading arrangement
(iii) Patch Cord.
(iv) Instruction Manual
With AC Motor 0.5 HP FHP Single Phase with loading arrangement
01
7. Complete Setup For performing :- To study speed control of three phase
induction motor using three phase ac
voltage controller 3 phase, 415 volt 1.0 HP
squirrel cage induction motor drive by
Micro Control Based firing angle
alongwith motor-generating set. Consisting
of AC Induction Motor 1 HP 415 V, 1440
RPM coupled to DC Shunt Generator
230V with lamp bank load.
DESCRIPTION 1. This unit consists of two parts :-
(a) Power Circuit :- It consist of 6
Thyristors connected in anti-parallel
(2SCRs in each phase). By controlling the
firing angle of the thyristors connected in
anti-parallel in each phase, the rms value
of the stator voltage can be regulated. As a
consequence, motor torque and thus speed
of the drive is controlled.
01
(b) Control Circuit:- FCR-100 (8051)
microcontroller based SCR Bridge
controller is used for controlling the firing
circuit.
2. Soft push buttons provided for
increasing or decreasing the firing angle.
3. 3-phase MCB
4. LCD display of the firing angle.
5. 10:1 Attenuator with Isolation
Transformer for observation of wave form
on CRO.
With AC Induction Motor 1 HP 415 V,
1440 RPM coupled to DC Shunt Generator
230V with lamp bank load.
8. Complete Setup For performing :- To study speed control of three phase
induction motor using three phase current
source inverter
01
9. Complete Setup For performing :- To study speed control of three phase
induction motor using three phase voltage
source inverter
01
10. Complete Setup For performing :- To study speed control of three phase slip
ring induction motor using static rotor
resistance control using rectifier and
chopper
(a) Power Circuit: This part consists of a
3-phase bridge rectifier to convert 3-phase
rotor supply to DC supply. An indicator is
connected in series with the DC supply for
smoothning of a DC. A Glass fuse is
connected in series with the DC supply. An
IGBT is provided for chopper control
MOSFET is mounted on a proper heat
sink. Snubber circuit is connected across
MOSFET for dv/dt. A fuse is also provided
for protection. All the points are brought
out on the front panel for interconnection.
(b) Control Circuit: The control circuit
generates driver output for driving the
MOSFET in chopper mode. The duty cycle
can be varied from 0% to 90%. The
frequency can be varied.
Soft start and soft stop is provided for
driver output
01
11. Complete Setup For performing :- To study speed control of three phase slip
ring induction motor using static scherbius
slip power recovery control scheme
1 HP Induction Motor Slipring Type for
demonstration of speed variation of
induction motor. Ammeter/Voltmeter
provided alongwith the set up. Electronic
Controller includes Power Supply, Firing,
Circuit, Contactor, SCR Bridge Inverter
and 6 diode bridge converter for rotor side.
DV/DT protection for Thyristors included.
01
ss Total