Pumps and Systems - Zoeller Engineered Products · Pumps and Systems Commercial Duty Pumps ... From...

Trusted. Tested. Tough.™

Pumps and Systems

Commercial Duty Pumps

Heavy Duty Solids Handling Pumps

Hazardous Duty Pumps

Grinder Pumps and systems

Engineered Lift Stations

2© All rights reserved. ZOELLER CO. | 502-778-2731 | 800-928-7867 | zoellerengprod.com

WHAT SETS ZOELLER PUMPS APART?

Since 1939, Zoeller Company has been manufacturing water pumps of many types. From pedestal pumps in the beginning to large HP, submersible, non-clog pumps in recent years, we have gained invaluable manufacturing experience from our humble beginning in August Zoeller’s basement workshop.

Over the years, one of our most important mottos has been, ‘We excel at 1,000 little things’. From start to finish, we take pride in our products. When you have residential or commercial wastewater issues, you can count on Zoeller to deliver the very best solutions. Our commitment to unsurpassed quality offers years of service and durability with a responsive and knowledgeable product support team just a phone call away.

• MANUFACTURING IS IN OUR BLOOD…Rather than using a ‘puzzle piece’ mentality and simply buying components from other sources and assembling them, we manufacture most of our products from start to finish, continually checking the quality throughout the entire process.

Quality is always the most important element at Zoeller. Above all, quality is what has made us successful and continues to drive the decisions we make. A quality product cannot be manufactured with low-grade components. By bringing in high-quality raw castings as well as machining and powder coating the pieces in house, we are able to control the quality of each part and identify any defect throughout the manufacturing process. Each piece is subjected to numerous quality checkpoints along the way to guarantee that it is the best of the best.

• FACTORY TESTING IS NOT JUST A BUZZWORD…Instead of running ‘audits’ on a calculated number of pumps, all submersible Zoeller pumps are 100% factory tested underwater prior to shipment. Each pump is subjected to a leak test to ensure that all gaskets, seals and mating surfaces will hold under pressure. After the pressurized leak test, the pump is powered up and run underwater to ensure that it is capable of the published head capacity and flow rate listed in our catalog and specification sheets. This testing allows us to guarantee the pump will operate out of the box every time, and you can rest assured that YOUR Zoeller pump was tested underwater for both electrical and hydraulic performance.

• FULL BREADTH OF PRODUCT LINE…Zoeller is your ‘one stop shop’ when dealing with dewatering and wastewater systems. We offer everything from a small fractional sump pump to a large, 100 HP, non-clog pump. From battery back-ups, check valves, sewage grinder systems, small prepackaged residential units or large prepackaged municipal systems, Zoeller can offer it all. Next time you are looking for a water or wastewater system, reach for the only catalog you will ever need… Zoeller Company!


* 200V/1Ph Models and Model 6186 are not UL Listed.Products may not be exactly as pictured.

COMMERCIAL EFFLUENT 6100 SERIESFEATURES:• Submersible motor - 1/2 HP thru 2 HP, 60 Hz, 3450 RPM, 1 Ph or 3 Ph, oil-filled,

hermetically sealed, automatic reset thermal overload protected (1 Ph)• Bearings - Upper and lower ball• Dual shaft seals - Silicon carbide/carbon lower, carbon/ceramic upper• Square rings and gasket - Viton• Bronze, non-clogging vortex impeller design• Durable cast iron cover, base, motor and pump housing• 25' (8 m) UL listed, 3-wire neoprene cord and plug• Maximum temperature for effluent or dewatering: 130 °F (54 °C)• No screens to clog• Stainless steel screws, bolts, handle, seal assembly and shaft• Passes 3/4" (19 mm) spherical solids• 1-1/2" NPT discharge with 2" or 3" flange available• Corrosion-resistant, powder coated epoxy finish• 100% computer tested

COMMERCIAL SEWAGE 6200 & 6400 SERIESFEATURES:• Submersible motor - Oil-filled, hermetically sealed, automatic reset thermal

overload protected (1 Ph) - 6280 Series: 1/2 or 1 HP, 60 Hz, 1750 RPM, 1 Ph or 3 Ph - 6290 Series: 1/2 thru 2 HP, 60 Hz, 3450 RPM, 1 Ph or 3 Ph - 6400 Series: 2 HP & 3 HP, 60 Hz, 1750 RPM, 1 Ph or 3 Ph• Square rings and gasket - Viton• Bearings - Upper and lower ball• Dual shaft seals - silicon carbide/carbon lower, carbon/ceramic upper• Non-clogging cast iron vortex impeller • Durable cast iron cover, base, motor and pump housing• 25' (8 m) UL listed, 3-wire neoprene cord and plug• Stainless steel screws, bolts, handle, seal assembly and shaft• 6200 Series passes 2" (50 mm) spherical solids. 6400 Series passes 3" (76 mm)

spherical solids• 6200 models are available in 2" and 3" discharge. 6400 models are 4" discharge• Corrosion-resistant, powder coated epoxy finish• 100% computer tested

AVAILABLE OPTIONS: • Cord lengths of 35' (11 m) or 50' (15 m)• Silicon carbide seal upgrade• Moisture sensors for early warning of seal failure• FM and CSA Listed, Class I, Division 1, Group C & D motors• Certified performance tests

ACCESSORIES:• Rail systems and disconnects for standard installations• UL Listed simplex and duplex control panels with NEMA 1 and 4X enclosures

and float switches. Intrinsically safe relays for hazardous locations• Fiberglass basins, steel or aluminum access covers with hatches• Stainless steel and galvanized steel lifting cables• Cast iron check valves

6200 & 6400 Sewage Series

6100 Effluent Series

6160/6180

Explosion ProofX6100-X6200-X6400 Series

X6160/X6180 X6280/X6290

Standard 3600 & 3615

*

Tested to UL Standard UL778.

R LU

*


R LU

R

Certified to CSAStandard C22.2 No.108.

R


R


Commercial Effluent & Sewage Ejectors

6280/6290 6404/6405


009904

009922

LITERSGALLONS

FLOW PER MINUTE

6185

6188

PUMP PERFORMANCE CURVELARGER EFFLUENT MODELS

1/2" & 3/4" SOLID PASSING CAPACITY

TOTA

L DY

NAM

IC H

EAD

6163

6161

6165

6186

6189

4

0

25

10

6

8

15

20

25

30

0

10

80 160

20 30 40

240

50 60 70

400320

80 90 100

480

120110 130

560

150140

28

26

30

32

90

85

95

105

100

34

36

115

110

120

16

14

18

20

22

60

50

45

55

65

75

70

2480

10

12

35

40M

ETER

S

FEETPump Performance

CurvesWARNING: Model 6185 should not be subjected to less than 30' (9.1 m) TDH.

FA M I LY O W N E D

PROUDAMERICAN

®

960

35

800

4

10

LITERSGALLONS

03020

52

10

15

206

6282

30

258

10

880800560 640 720480400320240160FLOW PER MINUTE

6292

906040 50 8070 120100 110 140130 200

6284

160150 170 180 190

6295

230220210 250240

TOTA

L DY

NAM

IC H

EAD

4514

4012

50

55

16

20

22

6018

65

70

75

24

MET

ERS

FEET

80

6293

1360120011201040 1280

310280270260 300290

6404

340330320 350 360

6405

370

6294

PUMP PERFORMANCE CURVE SEWAGE MODELS2" SOLID PASSING CAPACITY

WARNING: Model 6293 should not be subjected to less than 15' (4.6 m) TDH.


3" NPT Discharge61 HD Series

1-10 BHP

Flanged Discharge61 HD & 62 HD Series

3", 1-10 BHP 4", 1-20 BHP 6", 5.0-20 BHP

Flanged Discharge64 HD Series

4" & 6", 25-60 BHP

3" NPT DischargeX61 HD Series

1-10 BHP

Flanged DischargeX61 HD & X62 HD

3", 1-10 BHP 4", 1-20 BHP 6", 5-20 BHP

ZEPA0465C

ZEPA0558

FEATURES:• Pump motor housing and volute - ASTM A-48 Class 30 cast iron• Stainless steel hardware• Corrosion-resistant, powder coated epoxy finish• Ductile iron impeller• Carbon/ceramic tandem mechanical seals protect the motor• Balanced concentric pump housing and impeller• Lifting lugs integral to the cast housing• 61 HD, 62 HD & 64 HD Series with oil-filled motors. Moisture probes

and temperature sensor with lead wires (optional on 61 HD Series). Single phase starting components are shipped loose or in optional enclosure

• X61 HD and X62 HD Series with FM and CSA Listed explosion proof motors (Class I, Division 1, Group C & D). Moisture probes and thermal sensors with lead wires are standard

• All models have a Class F insulation system with a maximum internal operating temperature of 294 °F (146 °C)

• All pumps pass 3" (76 mm) spherical solids. Standard on 62 HD, X62 HD and 64 HD Series. Optional on 61 HD & X61 HD 4" discharge units

• Two vane semi-open impellers with top pump-out vanes, enclosed impeller with top pump-out vanes, and vortex impellers with top pump-out vanes are available on selected models

• 25' (8 m) standard Type SO 4 conductor cords. Assembly engineered for water tightness

AVAILABLE OPTIONS:• Vortex impeller (1 BHP thru 15 BHP)• 3450 RPM motors (61 HD & X 61 HD - 5, 7-1/2 & 10 BHP only)• Additional cord lengths• Trimmed impellers• Silicon carbide seals• Viton Elastomers• Seal leak probes and thermal sensors (61 HD Series)• Bronze impellers• Dry pit configuration (61 HD and 62 HD Series only)• High temperature design (61 HD and 62 HD Series only)• Inverter duty motor• Certified performance tests

ACCESSORIES:• Rail systems (cast iron/stainless steel) fitted for standard installations

and non-sparking for Class I, Division 1, Group C and Group D installations

• UL Listed simplex and duplex control panels with NEMA 4X enclosures • Intrinsically safe relays for Explosion-proof Series• Fiberglass basins, steel or aluminum access covers with hatches• Cast iron check valves• Cast iron plug valves• Dry pit base elbow• Stainless steel and galvanized steel lifting cables• Rail system adapters for using Zoeller pumps on competitors’ rail

systems

Standard Solids Handling Solids Handling with Explosion Proof Motors

ZEPA0462B

ZEPA0233B

ZEPA0556

R

Certified to CSAStandard C22.2 No. 108


R


R


R


R


R



X62 HD

R

Heavy Duty Solids Handling and Hazardous Duty Series

ZEPA0273A

Flanged DischargeX64 HD Series

4" & 6", 25-60 BHP


Standard Oil-Filled Motors 1-20 BHP

SEMI-OPEN IMPELLER

TOTA

L DY

NAM

IC H

EAD

GALLONSLITERS

FLOW PER MINUTE

MET

ERS

FEET

PUMP PERFORMANCE CURVES FOR SEWAGE/WASTE SUBMERSIBLE PUMPS

MODELS 6111-6113 & 6222 HH - 6224 HH W/ SEMI-OPEN IMPELLERS

013936

0

50 100 150 200 250 300 350 400 450 500 550 600 650 700 750 800 8500

5

10

15

20

25

30

35

40

45

50

55

60

65

70

75

200 400 600 800 1000 1200 1400 1600 1800 2000 2200 2400 2600 2800 3000 3200

2

4

6

8

10

12

14

16

18

20

22

LITERSGALLONS

MET

ERS

FEET

PUMP PERFORMANCE CURVES FOR SEWAGE/WASTE SUBMERSIBLE MODELS 6111-6113, 6120-6125 & 6220-6223

W/VORTEX IMPELLERS

6220

6221 6222

6223

FLOW PER MINUTE

TOTA

L DY

NAM

IC H

EAD

612461216120 6122 6123 6125

8024

6111

6112

6113

VORTEX IMPELLER

SEMI-OPEN IMPELLER

PUMP PERFORMANCE CURVES FOR SEWAGE/WASTE SUBMERSIBLE MODELS 6120 - 6125 & 6220 - 6224

W/ SEMI-OPEN IMPELLERSM

ETE

RS

FEE

T

GALLONSLITERS

FLOW PER MINUTE

TOTA

L D

YN

AM

IC H

EA

D

014486

013937

Pump Performance Curves


PUMP PERFORMANCE CURVES FOR SEWAGE/WASTE SUBMERSIBLE PUMPSMODELS 6424-6428 W/ENCLOSED IMPELLERS, 6424HH-6428HH W/SEMI-OPEN IMPELLERS

70

TOTA

L DY

NAM

IC H

EAD

8

GALLONS

LITERS

0

0

100

20

104

300

800

200

1600

400

40

30

12

60

5016

20

FLOW PER MINUTE

800

2400

500 600 700 1000

3200

900

4000

1100

5600

15001300

4800

1200 1400 1600

6400

1700 1800

6424

28 90

8024

110

100

32

130

12036

MET

ERS

FEET

6426

9600

250022002000

7200

1900

8000

2100

8800

2300 2400

6425

27002600

64286427

200

150

140

170

160

190

180

44

40

48

52

56

60

6424HH

6426HH

6427HH

6428HH

6425HH

012996

* 3450 RPM motors ** 3" (76 mm) spherical solids capacity also available on 4" discharge units. *** High Head Models 6222, 6223 and 6224 available in 4" discharge only. Consult Factory for other voltages and frequencies.

Standard Oil-Filled Motors 25-60 BHP

PREFIX VOLTAGE/CYCLE CODE: E = 230 V, 1 Ph, 60 Hz F = 230 V, 3 Ph, 60 Hz G = 460 V, 3 Ph, 60 Hz J = 200 V, 3 Ph, 60 Hz BA = 575 V, 3 Ph, 60 Hz

DISCHARGES: 3" NPT vertical discharge 3" flanged horizontal discharge 4" flanged horizontal discharge 6" flanged horizontal discharge


PREFIXCODE

MODEL NUMBER BHP DISCHARGES SOLIDS

CAPACITY

E-F-G-J-BA 6111 5.0* 3" 2-1/2" (63 mm)F-G-J-BA 6112 7.5* 3" 2-1/2" (63 mm)F-G-J-BA 6113 10.0* 3" 2-1/2" (63 mm)E-F-G-J-BA 6120 1.0 3", 4" 2-1/2" (63 mm)**E-F-G-J-BA 6121 1.5 3", 4” 2-1/2" (63 mm)**E-F-G-J-BA 6122 2.0 3", 4" 2-1/2" (63 mm)**E-F-G-J-BA 6123 3.0 3", 4" 2-1/2" (63 mm)**E-F-G-J-BA 6124 5.0 3", 4" 2-1/2" (63 mm)**E-G-J-BA 6125 7.5 3", 4" 2-1/2" (63 mm)**E-F-G-J-BA 6220 5.0 4", 6" 3" (76 mm)E-F-G-J-BA 6221 7.5 4", 6" 3" (76 mm)F-G-J-BA 6222 10.0 4", 6" *** 3" (76 mm)F-G-J-BA 6223 15.0 4", 6" *** 3" (76 mm)F-G-J-BA 6224 20.0 4", 6" *** 3" (76 mm)F-G 6424 HH 25.0 4" 3-1/8" (79 mm)F-G 6425 HH 30.0 4" 3-1/8" (79 mm)G 6426 HH 40.0 4" 3-1/8" (79 mm)G 6427 HH 50.0 4" 3-1/8" (79 mm)G 6428 HH 60.0 4" 3-1/8" (79 mm)F-G 6424 HF 25.0 6" 4" (101 mm)F-G 6425 HF 30.0 6" 4" (101 mm)G 6426 HF 40.0 6" 4" (101 mm)G 6427 HF 50.0 6" 4" (101 mm)G 6428 HF 60.0 6" 4" (101 mm)


016748

SEMI-OPEN IMPELLER

PUMP PERFORMANCE SURVES FOR EXPLOSION PROOFMODELS X6120 - X6125 & X6220 - X6224

W/ SEMI-OPEN IMPELLERSM

ETE

RS

FEE

T

GALLONSLITERS

FLOW PER MINUTE

TOTA

L D

YN

AM

IC H

EA

D

0

50 100 150 200 250 300 350 400 450 500 550 600 650 700 750 800 8500

5

10

15

20

25

30

35

40

45

50

55

60

65

70

75

200 400 600 800 1000 1200 1400 1600 1800 2000 2200 2400 2600 2800 3000 3200

2

4

6

8

10

12

14

16

18

20

22

LITERSGALLONS

MET

ERS

FEET PUMP PERFORMANCE CURVES FOR EXPLOSION PROOF

MODELS X6111-X6113, X6120-X6125 & X6220-X6223W/VORTEX IMPELLERS

X6220

X6221 X6222

X6223

FLOW PER MINUTE

TOTA

L DY

NAM

IC H

EAD

X6124X6121X6120 X6122 X6123 X6125

75

X6111

X6112

X6113

VORTEX IMPELLER

016749

0

50 100 150 200 250 300 350 400 450 500 550 6000

10

20

30

40

50

60

70

80

90

120

GALLONSLITERS

MET

ERS

FEET

200 400 600 800 1000 1200 1400 1600 1800 2000 2200

2

4

6

8

10

12

14

16

18

20

22

24

26

28

PUMP PERFORMANCE CURVES FOR EXPLOSION PROOF MODELSX6111-X6113 & X6222HH-X6224HH

W/SEMI-OPEN IMPELLERS

FLOW PER MINUTE

TOTA

L DY

NAM

IC H

EAD

30

32

34

36

100

110

650

2400 2600

X6111

X6112

X6113

X6222HH

X6223HH X6224HH

SEMI-OPEN IMPELLERS

016747

Explosion Proof Motors 1-20 BHP



PUMP PERFORMANCE CURVES FOR SEWAGE/WASTE SUBMERSIBLE PUMPS

MODELS X6424 - X6428 WITH ENCLOSED IMPELLERS

PUMP PERFORMANCE CURVES FOR SEWAGE/WASTE SUBMERSIBLE PUMPSMODELS X6424-X6428 W/ENCLOSED IMPELLERS, X6424HH-X6428HH W/SEMI-OPEN IMPELLERS

70

TOTA

L DY

NA

MIC

HEA

D

8

GALLONS

LITERS

0

0

100

20

104

300

800

200

1600

400

40

30

12

60

5016

20

FLOW PER MINUTE

800

2400

500 600 700 1000

3200

900

4000

1100

5600

15001300

4800

1200 1400 1600

6400

1700 1800

X6424

2890

8024

110

100

32

130

12036

MET

ERS

FEET

X6426

9600

250022002000

7200

1900

8000

2100

8800

2300 2400

X6425

27002600

X6428X6427

200

150

140

170

160

190

180

44

40

48

52

56

60

X6424HH

X6426HH

X6427HH

X6428HH

X6425HH

012996X

* 3" (76 mm) spherical solids capacity also available on 4" discharge units. ** High Head Models X6222 - X6224 available in 4" discharge only. Consult factory for other voltages and frequencies.

PREFIX VOLTAGE/CYCLE CODE: E= 230 V, 1 Ph, 60 Hz F= 230 V, 3 Ph, 60 Hz G= 460 V, 3 Ph, 60 Hz J = 200 V, 3 Ph, 60 Hz BA = 575 V, 3 Ph, 60 Hz

DISCHARGES: 3" NPT vertical discharge 3" flanged horizontal discharge 4" flanged horizontal discharge 6" flanged horizontal discharge

Air-Filled, Explosion Proof Motors 25-60 BHP


PREFIXCODE


CAPACITY

E-F-G-J-BA X6111 5.0 3" 2-1/2" (63 mm)E-F-G-J-BA X6112 7.5 3" 2-1/2" (63 mm)E-F-G-J-BA X6113 10.0 3" 2-1/2" (63 mm)E-F-G-J-BA X6120 1.0 3", 4" 2-1/2" (63 mm)*E-F-G-J-BA X6121 1.5 3", 4" 2-1/2" (63 mm)*E-F-G-J-BA X6122 2.0 3", 4" 2-1/2" (63 mm)*E-F-G-J-BA X6123 3.0 3", 4" 2-1/2" (63 mm)*E-F-G-J-BA X6124 5.0 3", 4" 2-1/2" (63 mm)*F-G-J-BA X6125 7.5 3", 4" 2-1/2" (63 mm)*E-F-G-J-BA X6220 5.0 4", 6" 3" (76 mm)F-G-J-BA X6221 7.5 4", 6" 3" (76 mm)F-G-J-BA X6222 10.0 4", 6" ** 3" (76 mm)F-G-J-BA X6223 15.0 4", 6" ** 3" (76 mm)F-G-J-BA X6224 20.0 4", 6" ** 3" (76 mm)F-G-BA X6424 HH 25.0 4" 3-1/8" (79 mm)F-G-BA X6425 HH 30.0 4" 3-1/8" (79 mm)G-BA X6426 HH 40.0 4" 3-1/8" (79 mm)G-BA X6427 HH 50.0 4" 3-1/8" (79 mm)G-BA X6428 HH 60.0 4" 3-1/8" (79 mm)F-G-BA X6424 HF 25.0 6" 4" (101 mm)F-G-BA X6425 HF 30.0 6" 4" (101 mm)G-BA X6426 HF 40.0 6" 4" (101 mm)G-BA X6427 HF 50.0 6" 4" (101 mm)G-BA X6428 HF 60.0 6" 4" (101 mm)


Models: 6920 - 692820 - 100 BHP

Standard Air-Filled and Explosion Proof Motors

OIL LEVEL

SK2479

FEATURES:PUMP:• Solids capacity - 3" (76 mm) spherical• Discharge size - 4" & 6" horizontal flanged• Seals - SC/SC lower, SC/C upper, Viton elastomers• Seal leak probes• Construction - Cast Iron ASTM A-48, Class 30, 30,000# tensile strength• Attaching hardware - 304 stainless steel• O-ring elastomers - Buna-N• Cast iron impeller - Dual vane enclosed design• Polyurethane pump housing wear ring (20-40 BHP units)• Optional: □ Trimmed Impeller □ Rail Systems □ Additional cord length ____ 4" x 4" (10 x 10 cm) □ SS Pump Housing Wear Ring 4" x 6" (10 x 15 cm) □ SS Impeller Wear Ring 6" x 6" (15 x 15 cm) 6" x 8" (15 x 20 cm) 6" x 10" (15 x 25 cm)MOTOR:• 3 Phase - 1750 RPM• Stator - Class H insulation and lead wires• Nema design• Thermal sensor protection• Housing - Finned cast iron, air-filled• Ball bearings - Dual high carbon chromium steel• Power cable length - 30' (9 m)• Optional: □ FM Listed Explosion Proof Motor □ Inverter Duty Motor

Pump Performance Curves4" Discharge

PUMP PERFORMANCE CURVEMODELS 6920, 6921, 6923, 6924

(4" DISCHARGE)

0 800

15009008007006005004003002001000

5 15

180

105

90

75

60

45

30

FLOW PER MINUTE

GALLONSLITERS

TOTA

L DY

NAM

IC H

EAD

120

135

MET

ERS

FEET

150

165

1000 1100 1200 1300 1400

10

15

20

25

30

35

40

45

50

L

L60

%65%67

%

68%67

%

68%

65%

50%

60%

6920

6921

6923

6924

11"

12"

10"

L

10-1/2"

11-1/2"

20 GPM(75.6 LPM)

3 FT.(0.9 m)

1600 2400 3200 4000 4800 5600

B00611 B00612


(4" DISCHARGE)

14009008007006005004003002001000

25

300

175

150

125

100

75

50

TOTA

L DY

NAM

IC H

EAD

200

225

MET

ERS

FEET

250

275

1000 1100 1200 1300

0 800

FLOW PER MINUTE

U.S. GALLONSLITERS

10

20

30

40

50

60

70

80

90

68%

68%

L

L

67%65

%64%61

%58%52

%

6928

6925

6926

6927

12-3/8"

14"

15"

12"

13-1/4"

1600 2400 3200 4000 4800

20 GPM(75.6 LPM)

5 FT.(1.5 m)

69 HD Series


Pump Performance Curves6" Discharge

B00613

PUMP PERFORMANCE CURVEMODELS 6921, 6923, 6924

(6" DISCHARGE)

3200180016001400120010008006004002000

TOTA

L DY

NAM

IC H

EAD

MET

ERS

FEET

2000 2200 2400 2600 2800 3000

0 1600

FLOW PER MINUTE

U.S. GALLONSLITERS

6924

6921

72%

69%

72%

69%

66%

64%

60%

55%

50%

6923

L

L

66%

11"

10

20

30

40

50

60

70

80

90

100

110

120

130

140

10

20

30

40

5

15

25

35

10-1/2"

9-1/8"

9-3/4"

3200 4800 6400 8000 9600 11200

64%

40 GPM(151 LPM)

2 FT.(0.6 m)

B00614


(6" DISCHARGE)

35002250200017501500125010007505002500

1025

275

175

150

125

100

75

50TO

TAL

DYNA

MIC

HEA

D

200

225

MET

ERS

FEET

2500 2750 3000 3250

250

0

FLOW PER MINUTE

U.S. GALLONSLITERS 1500

20

30

40

50

60

70

80

60%

65%

70%

73%

75%

75%

73%

70%65

%60%

692869276926

6925

14"

L

L

12-1/8"

12-3/4"

13-1/2"

14-7/8"

3000 4500 6000 7500 9000 10500 12000

50 GPM(189 LPM)

5 FT.(1.5 m)

PREFIX VOLTAGE/CYCLE CODE: F= 230 V, 3 Ph, 60 Hz G= 460 V, 3 Ph, 60 Hz J = 200 V, 3 Ph, 60 Hz BA = 575 V, 3 Ph, 60 Hz

DISCHARGES: 4" flanged horizontal discharge 6" flanged horizontal discharge

69 HD Series

PREFIXCODE


CAPACITY

F-G-J-BA 6920 20 4" 3" (76 mm)F-G-J-BA 6921 25 4", 6" 3" (76 mm)F-G-J-BA 6923 30 4", 6" 3" (76 mm)F-G-J-BA 6924 40 4", 6" 3" (76 mm)F-G-J-BA 6925 50 4", 6" 3" (76 mm)F-G-J-BA 6926 60 4", 6" 3" (76 mm)F-G-J-BA 6927 75 4", 6" 3" (76 mm)F-G-J-BA 6928 100 4", 6" 3" (76 mm)


Models 7008, 7009, 70101, 1.5, 2 HP Grinder Pumps

STANDARD FEATURES:• 1-1/4" NPT vertical discharge• Silicon carbide/carbon mechanical seal• Thermal overload protection (1 Ph)• Engineered plastic, glass-filled impeller• Stainless steel cutter plate/cutter, shaft and hardware• Viton square rings and gasket• 20' (6 m) power cord• Submersible motor, 60 Hz, 3450 RPM• Corrosion-resistant, powder coated epoxy finish

OPTIONS:• Silicon carbide/silicon carbide mechanical seal• Additional cord lengths• Automatic model with integral control• Bronze impeller• Trimmed impeller (requires bronze impeller)

20

30

40

50

60

10 15 20 25 30 35 40 45 50 555

20 40 60 80 100 120 140 160 180 200

0

MET

ERS

FEET

PUMP PERFORMANCE CURVE MODELS 7008/7009/7010

0

TOTA

L DY

NAM

IC H

EAD

FLOW PER MINUTE

GALLONSLITERS

70

10

80

90

100

110

4

8

12

16

20

24

28

32 7010

7009

7008

154108

Models 7020 & 70211 & 2 HP - Progressing CavitySTANDARD FEATURES:

• 1-1/4" NPT horizontal discharge• Construction - Motor housing, cover, adapter and pump housing

cast iron ASTM A-48, Class 30, 30,000# tensile strength, corrosion-resistant, powder coated epoxy finish

• Viton square rings and gasket• Stainless steel cutter and plate hardened to Rockwell C 55-60• Pressure relief valve• Stainless steel legs provide for free-standing installation• Stainless steel helix hydraulic rotor• Buna-N hydraulic stator• 230 V / 1 Ph, 1750 RPM, 1 & 2 HP• Housing - Finned cast iron, oil-filled

0

2 4 6 8 10 12 14 160

20

40

60

80

100

120

140

160

180

200

260

8

16

24

32

40

48

56

64

GALLONSLITERS

MET

ERS

FEET

TOTA

L DY

NA

MIC

HEA

D

FLOW PER MINUTE

220

24072

20 40 60

10

20

30

40

50

60

70

80

90

100

110

0

PSIG

TOTA

L DY

NA

MIC

HEA

DPUMP PERFORMANCE CURVE

MODEL 7020/7021

2 HP

1 HP

LOW PRESSURE SEWER

TYPICALOPERATING

RANGE

DESIGN PRESSURE (150 FT OR LESS)

018330

Model 7011 - 2 HP Bidirectional Dual Seal Grinder PumpModel 7012 - 2 HP Single Directional High HeadModel 7013 - 2 HP Single Directional High FlowSTANDARD FEATURES:• 1-1/4" NPT vertical discharge• Tandem seals - Silicon carbide/carbon lower, carbon/ceramic upper• Class F insulated motor• Thermal sensors (O.L. on 1 Ph)• Moisture probes• Vortex impeller: Ductile iron (7011), Bronze (7012 & 7013)• Stainless steel (R-C 55-60) cutter, plate and shaft seal• Viton square rings• Corrosion-resistant, powder coated epoxy finish• 20' (6 m) power and sensor cord• Submersible motor, 3450 RPM

OPTIONS:• Silicon carbide/silicon carbide seal(s)• Additional cord lengths• Bronze Impeller (7011 only)• Trimmed impeller• FM & CSA Listed Class I, Division 1, Group C & D

Hazardous Location Series016532

HEAD CAPACITY CURVE MODEL 7011/7012/7013

0 40 80 120 160 200 240

706050403020100

104

8

12

16

20

130

70

60

50

40

30

20

FLOW PER MINUTE

GALLONSLITERS

TOTA

L DY

NA

MIC

HEA

D

80

9028

24

MET

ERS

FEET

100

110

120

32

36

7011 70137012

70 Series Grinder Pumps

*


R LU

R


R


R



TO CONTROL

30”(76.2 cm)

36”(91.4 cm)

PUMPS ROTATED 90° TO SHOW FEATURES

OFF

ON

ALARMOVERRIDE

INDOOR BASIN, COVER, AND HARDWARE - PREPACKAGED STANDARD EQUIPMENT

• Fiberglass basin• Simplex and Duplex configurations• Rust-resistant steel cover (epoxy coated only)• Inspection plate• Individual pump covers• 3" (DN80) Adaptaflex vent seal• 1-1/4" (DN32) Adaptaflex discharge pipe seal(s)• Cord seal(s) for 3 & 4 float systems• 1 - 4" Cast iron hub• Pump support hardware• 1-1/4" Check valve(s)• Ball valve(s)

All Grinder system components are available individually.

PUMPS NOTINCLUDED

OUTDOOR BASIN, COVER, AND RAIL SYSTEM ASSEMBLIES - STANDARD EQUIPMENT

• Fiberglass basin with anti-flotation ring• Simplex and Duplex configurations with a variety of depths• Z-Rail® disconnect system• 2" (DN50) PVC discharge pipe from disconnect• 2" (DN50) Adaptaflex discharge pipe seal• 2" (DN50) PVC or optional metallic pipe• Stainless steel or galvanized rail(s)• Stainless steel lifting cable• 2" (DN50) PVC ball valve(s)• 2" Cast iron check valve(s)• 1 - 4" inlet fitting • Solid or hatched cover• Special sizes and configurations available by request

SK2990

SK1326

TYPICAL DUPLEX INSTALLATION

6932-0018 REPLACEMENT ASSEMBLY FORPOSITIVE DISPLACEMENT GRINDER PUMP

• Readily adapts to existing progressing cavity grinder pump systems• Quick disconnect coupling• Model 7020 pump is cCSAus listed• Dual-action Y-splice float control• Corrosion-resistant, powder coated epoxy finish• Discharge size - 1-1/4" NPT• 230 V / 1 Ph, 60 Hz, 1 HP, 1750 RPM• 20' ( 6 m) electrical cords with quick disconnect

receptacle fitting• Hardened stainless steel cutter and disc, Rockwell C55-60• Stainless steel hydraulic pump rotor• Pressure relief valve• Check valve• Anti-siphon device

PUMP CONTROL"ON-OFF" FLOAT

1-1/4" BRASS CHECK VALVE

1-1/4" GAVALVANIZEDDISCHARGE PIPING

1-1/4" BRASSANTI-SIPHON VALVE

ALARM FLOAT

CAST IRON ADAPTERS

SINGLE PHASE, 1HPPROGRESSING CAVITY

GRINDER PUMP

CORD SEAL

1-1/4" GROMMET SEAL

(12) Ø13/32 THRU HOLESEQUALLY SPACED ON

15-1/16 BOLT CIRCLE

�15-3/4

1/8" STAINLESS STEELLIFTING CHOKER

90°

1-1/4" STAINLESS STEELDISCHARGE FITTING

SEALING NUT

BASIN(SUPPLIED BY OTHERS)

DISCHARGE ASSEMBLY(BY OTHERS)

ELECTRICAL QUICKDISCONNECT

10-1/2

12-3/8”

SK3077

Grinder Pump Package Systems

TYPICAL SIMPLEX INSTALLATION

PUMPS NOTINCLUDED

PUMP CONTROL"ON-OFF" FLOAT

1-1/4" BRASS CHECK VALVE

1-1/4" GAVALVANIZEDDISCHARGE PIPING

1-1/4" BRASSANTI-SIPHON VALVE

ALARM FLOAT

CAST IRON ADAPTERS

SINGLE PHASE, 1HPPROGRESSING CAVITY

GRINDER PUMP

CORD SEAL

1-1/4" GROMMET SEAL

(12) Ø13/32 THRU HOLESEQUALLY SPACED ON

15-1/16 BOLT CIRCLE

�15-3/4

1/8" STAINLESS STEELLIFTING CHOKER

90°

1-1/4" STAINLESS STEELDISCHARGE FITTING

SEALING NUT

BASIN(SUPPLIED BY OTHERS)

DISCHARGE ASSEMBLY(BY OTHERS)

ELECTRICAL QUICKDISCONNECT

10-1/2

12-3/8”


71 & X71 Series Grinder PumpsModels: 7110 (3 HP), 7111 (5 HP) & 7112 (7-1/2 HP)

Models: X7110 (3 HP), X7111 (5 HP) & X7112 (7-1/2 HP)

71 & X71 HH SERIES GRINDER PUMPS3, 5 & 7-1/2 HP

FLANGED DISCHARGE

2 GPM(7.6 LPM)

3 FT.(0.9 m)

ME

TER

S

FEE

T

GALLONS

LITERS

TOTA

L D

YN

AM

IC H

EA

D

FLOW PER MINUTE

7-1/8” DIA.

6-1/4” DIA.6” DIA.

5-1/4” DIA.

7-1/2 HP 3ø

5 HP 1ø

3 HP

5 HP 3ø

A00523

400

104

50

72

GALLONS

LITERS

0

0

12

8

5

10

15

20

24

36

48

60TOTA

L DY

NAM

IC H

EAD

25

30

35

84

96

108

120

MET

ERS

40

45

FEET

144

132

FLOW PER MINUTE

100

2416 32

150 200

4840 56

250 300

64 72 80

350

88 96

3, 5, AND 7-1/2 HP71 & X71 REVERSING SERIES GRINDER PUMPS

112

3 HP 3Ø4-3/8" DIA

6-1/8" DIA 7-1/2 HP 3Ø

5 HP 3Ø5-1/8" DIA

3 PHASE - FLANGED DISCHARGE

2 GPM(7.6 LPM)

3 FT.(0.9 m)

STANDARD FEATURES:PUMP:• 3 configurations - High Head - High Flow - Reversible

• 440 Stainless steel cutter & plate hardened to Rockwell C55-60

• Discharge size - 2-1/2" flanged horizontal adaptable to 3" flange

• Seals - dual mechanical carbon/rotary ceramic/stationary, Buna-N elastomers

• Seal leak probes and lead wires

• Construction - cast iron ASTM A-48, Class 30, 30,000# tensile strength, protected with a corrosion-resistant, baked-on epoxy powder coating

• Balanced concentric pump housing and impeller

• Impeller - Ductile iron vortex design

MOTOR:• 1 Phase - 230 Volts

(3 & 5 HP High Head & High Flow models only)

• 3 Phase - 200/230/460/575 Volts, 3450 RPM

• Stator - Class F insulation and lead wires Nema B design

• Thermal sensor with leads

• Housing - Class 30 cast iron, oil-filled

A00549

5 GPM(19 LPM)

5 FT.(1.5 m)

7-1/2 HP

5 HP

3 HP

MET

ERS

FEET

TOTA

L DY

NAM

IC H

EAD

FLOW PER MINUTE

GALLONSLITERS

71 & X71 HIGH FLOW SERIES GRINDER PUMPS3, 5 & 7-1/2 HP

FLANGED DISCHARGE

6” DIA.

5-1/4” DIA.

4-1/4” DIA.

A00550

R

Tested to UL Standard UL778

& Certified to CSA Standard C22.2 No. 108

3, 5 & 7-1/2 HP Grinder Pump Series

• Ball bearings - Upper and lower high carbon chromium steel

• Power & sensor cable length - 25' (8 m)

OPTIONS:• 2" NPT Vertical Discharge (HH & HF models only)

• Trimmed impeller

• Silicon carbide seal(s)

• Viton Elastomers

• Bronze impeller

• Additional cord lengths

• FM and CSA Listed Class I, Division 1, Group C & D Hazardous Location models (X71 Series)


Refer to pages 17 & 18 regarding pump electrical data.Custom panel designs available by request

CONTROL PANEL STANDARDFeatures:• Simplex and Duplex configurations

• NEMA 4X outdoor rating

• Lockable hasp

• Pump disconnect

• Motor contactor

• 115 Volt control circuit

• Pilot lights and selection switches

• High water alarm circuits with dry contacts

• Seal leak indication

• Thermal cut-out circuit

• Reversing circuits for 7011 and 71 Series

Reversing Grinder pumps

C R LU US LISTED

2" - 8" CAST IRON PLUG VALVESThreaded Connection - 2" and 3"Flanged Connection - 2"- 8"

1-1/4" - 3" Threaded “Full-Flow” Unichecks

• Vertical or horizontal installation

• Full flow design - no restrictions

• Standard, 1-1/4", 1-1/2", 2", 3" female NPT pipe

• Neoprene polyester reinforced flapper - smooth edge design, with cast iron and noncorrosive metal backing plates and stainless steel fastener

• Rated at 50 psi (115' [35 m] of head) at 130 °F (54 °C)

• Cast iron body and stainless steel bolts

• Corrosion-resistant, powder coated epoxy finish

2" - 8" Flanged Check Valvesfor Sewage or Dewatering Applications• Heavy duty cast iron construction

• Angled seal for non-slam closure

• Non-clog design

• Reinforced disc

• Drip tight seating

• Rated up to 200 psig

• Designed for both horizontal and vertical use

FEATURES:• Designed to handle solids-bearing flows

• Cast iron housing - rated 175 psi

• 99% pure nickel welded seat

• 1/4 turn Buna plug

• Upper and lower ball bearings

• Provided with hand lever

Lift Station AccessoriesSTANDARD OPTIONS:• Inner door

• Elapsed time meter(s)

• Event counter(s)

• Alarm flasher

• Lightning arrestor/surge suppressor

• Anti-condensation heater

• Instrinsically safe relays for Class I and Division 1 location

• Redundant off circuit

3", 4" & 6" FLYGT GUIDE RAILSYSTEM ADAPTERSAdapter plates for retrofitting 3", 4" & 6" horizontal discharge pumps to existing Flygt dual-pipe rail systems.

ZEPA0392

FLYGT GUIDE RAIL SYSTEM ADAPTER PLATE

EXISTING FLYGT RAIL FITTING

CHOKER CABLE *

*Not Included

DESIGN FEATURES:• Cast iron construction

• Flange conforms to ANSI B16.10 fully flat/MSS SP-6

• For use with all pumps with 3", 4" or 6" horizontal discharges and 2" NPT rail pipe

• Flange gasket and stainless steel bolts included

4" X 6" FLANGED DRY PIT MOUNTING STAND WITH CLEAN OUT

DESIGN FEATURES:• Class 30 epoxy coated cast iron construction

• 6" inlet / 4" outlet

• Flanges conform to ANSI B16.10 fully flat/MSS SP-6

• For use on Dry-Pit pumps with 4" discharge

• 3" clean out plug

ZEPA0474


GUIDE RAIL SYSTEMS FOR FLANGED DISCHARGE PUMPS (4" & 6" DISCHARGE)• Automatic engagement and easy disengagement

• Class 30 cast iron fittings (4" & 6" flanged) discharge

• Epoxy coated casting discharge

• Supports pump

• 2" IPS guide rails, brass, stainless steel or galvanized steel pipes recommended (not furnished)

• Intermediate stabilizers for pits over 15' (4.6 m) deep

• Bronze fitted rail system available for non-sparking requirements for Class I, Division 1, Group C & D installations

ELECTRICAL CONDUIT

LAG PUMP "ON" FLOAT

ALARM FLOAT

LEAD PUMP "ON" FLOAT

" CAST IRON INLET HUB

STEEL ALUMINUM GAS TIGHT

JUNCTION BOX (OPTIONAL)

HATCH COVER

DISCHARGE PIPE

SIZE TYPE

RAIL SYSTEM

GUIDE RAILS

FIBERGLASS BASIN

SHUT-OFF VALVE

LIFTING CABLE SS GALVANIZED

ACCESS OPENING

" X "

" VENT (OPTIONAL)

HATCH COVER

LEAD PUMP "OFF" FLOAT

CAST IRON CHECK VALVE

SS CABLE BRACKET

" DISCHARGE PIPE

N

R

T A

O T

I O

N

R

T A

O T

I O

ANTIFLOATATION RING: FIBERGLASS ENCAPSULATED STEEL

NONE FIBERGLASS SK2723

ENGINEERED LIFT STATIONS• Factory assembled for job ready installation

• Built to specification and/or job requirements

• Fiberglass basins up to 96" (2.4 m) diameter and 240" (6.1 m) depth

• Steel and aluminum hatched access covers

• 3" through 6" rail systems and discharge piping

• PVC, galvanized and stainless steel discharge piping

• Check valves and ball or plug valves

• Optional attached valve box

Guide Rail Systems

Products may not be exactly as pictured 4" & 6" Systems 2-1/2" & 3" Horizontal Flanged

Z-RAIL® DISCONNECT SYSTEM FOR THREADED DISCHARGE PUMPS(1-1/4" - 1-1/2" - 2" - 3")• Ductile iron construction, epoxy powder coated for corrosion protection• Robust construction, designed to support a 300 lb. (136 kg) pump• Tested to seat at heads up to 160 PSI ( 370’ [113 m] TDH) • Provides for an easy pump install or removal operation with no need for personnel to

enter basin• Compact design for easy installation• Adaptable to most 1-1/4”, 1-1/2”, 2" and 3” pumps with a vertical NPT discharge• 1-1/4" horizontal NPT discharge available for progressing cavity grinder pumps• Grooved machined fit for a positive seated rail plate• O-ring seals prevents leakage• Uses 3/4" IPS guide rails• Intermediate stabilizer for pits over 12' (3.7 m) deep SK2976

DISCONNECT ELBOW

ELBOW

THREADED MALECONNECTION

GUIDE RAIL PLATE

(NOT INCLUDED)GUIDE RAIL

UPPER RAIL SUPPORT


Electrical Data(Control Panels Available Upon Request)

Pump Model # Voltage Phase HP FLA

6100 & X6100 SeriesN6161 115 1 1/2 15.5E6161 230 1 1/2 7.5I6161 200 1 1/2 8.8J6161 200 3 1/2 6.4F6161 230 3 1/2 5.2G6161 460 3 1/2 2.9

BA6161 575 3 1/2 2.4N6163 115 1 1/2 15.0E6163 230 1 1/2 7.5I6163 200 1 1/2 8.5J6163 200 3 1/2 6.0F6163 230 3 1/2 4.8G6163 460 3 1/2 2.9

BA6163 575 3 1/2 2.4E6165 230 1 1 10.2I6165 200 1 1 12.6J6165 200 3 1 7.5F6165 230 3 1 7.4G6165 460 3 1 3.7

BA6165 575 3 1 3.0E6185 230 1 1 9.8I6185 200 1 1 11.5J6185 200 3 1 7.5F6185 230 3 1 7.4G6185 460 3 1 3.7

BA6185 575 3 1 3.3E6186 230 1 1-1/2 13.7J6186 200 3 1-1/2 10.3F6186 230 3 1-1/2 9.2G6186 460 3 1-1/2 4.6E6188 230 1 1-1/2 14.0I6188 200 1 1-1/2 16.8J6188 200 3 1-1/2 10.3F6188 230 3 1-1/2 8.9G6188 460 3 1-1/2 4.6

BA6188 575 3 1-1/2 3.5E & WD6189 230 1 2 17.1

I6189 200 1 2 20.5J6189 200 3 2 13.2F6189 230 3 2 11.2G6189 460 3 2 6.0

BA6189 575 3 2 5.8

6200 & X6200, 6400 & X6400 SeriesN6282 115 1 1/2 10.3E6282 230 1 1/2 5.0I6282 200 1 1/2 6.1J6282 200 3 1/2 3.6F6282 230 3 1/2 3.0G6282 460 3 1/2 1.7

BA6282 575 3 1/2 1.4E6284 230 1 1 8.9I6284 200 1 1 9.3J6284 200 3 1 5.5F6284 230 3 1 5.0G6284 460 3 1 2.6

BA6284 575 3 1 2.2N6292 115 1 1/2 15.0E6292 230 1 1/2 7.5I6292 200 1 1/2 8.8J6292 200 3 1/2 6.4F6292 230 3 1/2 5.2G6292 460 3 1/2 2.9

BA6292 575 3 1/2 2.4E6293 230 1 1 10.2I6293 200 1 1 12.0J6293 200 3 1 8.2F6293 230 3 1 7.6G6293 460 3 1 4.0

BA6293 575 3 1 3.3E6294 230 1 1-1/2 13.7


6200 & X6200, 6400 & X6400 Series, continued

I6294 200 1 1-1/2 17.8J6294 200 3 1-1/2 10.8F6294 230 3 1-1/2 9.5G6294 460 3 1-1/2 4.8

BA6294 575 3 1-1/2 3.8 E & WD6295 230 1 2 17.1

I6295 200 1 2 20.5J6295 200 3 2 14.3F6295 230 3 2 12.2G6295 460 3 2 6.1

BA6295 575 3 2 4.9E & WD6404 230 1 2 12.9

I6404 200 1 2 14.4J6404 200 3 2 13.8F6404 230 3 2 10.5G6404 460 3 2 5.2

BA6404 575 3 2 4.1E & WD6405 230 1 3 19.0

I6405 200 1 3 20.2J6405 200 3 3 14.8F6405 230 3 3 12.2G6405 460 3 3 6.1

BA6405 575 3 3 4.8

61 HD & X61 HD SeriesPump

Model # Voltage Phase HP FLA

E6111 230 1 5.0 28.0J6111 200 3 5.0 17.5F6111 230 3 5.0 15.2G6111 460 3 5.0 7.6

BA6111 575 3 5.0 6.1J6112 200 3 7.5 25.3F6112 230 3 7.5 22.0G6112 460 3 7.5 11.0

BA6112 575 3 7.5 9.0J6113 200 3 10.0 32.2F6113 230 3 10.0 28.0G6113 460 3 10.0 14.0

BA6113 575 3 10.0 11.0E6120 230 1 1 6.9J6120 200 3 1 4.8F6120 230 3 1 4.2G6120 460 3 1 2.1

BA6120 575 3 1 1.7E6121 230 1 1.5 8.9J6121 200 3 1.5 5.9F6121 230 3 1.5 5.1G6121 460 3 1.5 2.6

BA6121 575 3 1.5 2.0E6122 230 1 2 14.5J6122 200 3 2 7.8F6122 230 3 2 6.8G6122 460 3 2 3.4

BA6122 575 3 2 2.7E6123 230 1 3 17.0J6123 200 3 3 11.0F6123 230 3 3 9.6G6123 460 3 3 4.8

BA6123 575 3 3 3.9E6124 230 1 5 28.0J6124 200 3 5 17.5F6124 230 3 5 15.2G6124 460 3 5 7.6

BA6124 575 3 5 6.1J6125 200 3 7.5 25.3F6125 230 3 7.5 22.0G6125 400 3 7.5 11.0

BA6125 575 3 7.5 9.0


CAUTION: All installation of controls, protection devices and wiring should be done by a qualified licensed electrician. All electrical and safety codes should be followed including the most recent National Electrical Code (NEC) and the Occupational Safety and Health Act (OSHA).


62 HD & X62 HD SeriesE6220 230 1 5.0 27.5J6220 200 3 5.0 17.5F6220 230 3 5.0 15.2G6220 460 3 5.0 7.6

BA6220 575 3 5.0 6.1E6221 230 1 7.5 36.7J6221 200 3 7.5 25.0F6221 230 3 7.5 22.0G6221 460 3 7.5 11.0

BA6221 575 3 7.5 9.0J6222 200 3 10.0 32.0F6222 230 3 10.0 28.0G6222 460 3 10.0 14.0

BA6222 575 3 10.0 11.0J6223 200 3 15.0 48.3F6223 230 3 15.0 41.7G6223 460 3 15.0 20.9

BA6223 575 3 15.0 16.4J6224 200 3 20 59.4F6224 230 3 20 54.0G6224 460 3 20 27.0

BA6224 575 3 20 22.0

64 HD SeriesF6424 230 3 25 68.0G6424 460 3 25 34.0

BA6424 575 3 25 27.0F6425 230 3 30 80.0G6425 460 3 30 40.0

BA6425 575 3 30 32.0G6426 460 3 40 52.0

BA6426 575 3 40 41.0G6427 460 3 50 62.0

BA6427 575 3 50 52.0G6428 460 3 60 75.0

BA6428 575 3 60 62.0

X64 HD SeriesFX6424 230 3 25 64.2GX6424 460 3 25 32.1

BAX6424 575 3 25 25.6FX6425 230 3 30 79.8GX6425 460 3 30 39.9

BAX6425 575 3 30 31.9FX6426 230 3 40 103.0GX6426 460 3 40 51.7

BAX6426 575 3 40 41.4GX6427 460 3 50 64.3

BAX6427 575 3 50 51.4GX6428 460 3 60 74.9

BAX6428 575 3 60 59.9


70 & X70 Grinder SeriesE7020 230 1 1 7.0E7021 230 1 2 10.5

WM7008 115 1 1 13.6N7008 115 1 1 13.6

WD7008 230 1 1 8.5E7008 230 1 1 8.5

WH7008 200 1 1 7.7I7008 200 1 1 7.7J7008 200 3 1 7.5F7008 230 3 1 6.9G7008 460 3 1 3.7

BA7008 575 3 1 2.7WD7009 230 1 1.5 10.8

E7009 230 1 1.5 10.8WH7009 200 1 1.5 12.0

I7009 200 1 1.5 12.0J7009 200 3 1.5 9.2F7009 230 3 1.5 8.2G7009 460 3 1.5 4.2

BA7009 575 3 1.5 3.2WD7010 230 1 2 13.7

E7010 230 1 2 13.7WH7010 200 1 2 15.0

I7010 200 1 2 15.0J7010 200 3 2 11.0F7010 230 3 2 9.9G7010 460 3 2 5.0

BA7010 575 3 2 3.9E7011 230 1 2 17.2I7011 200 1 2 20.0J7011 200 3 2 12.3F7011 230 3 2 10.8G7011 460 3 2 5.5

BA7011 575 3 2 4.5E7012 230 1 2 17.2I7012 200 1 2 20.0J7012 200 3 2 12.3F7012 230 3 2 10.8G7012 460 3 2 5.5

BA7012 575 3 2 4.5E7013 230 1 2 17.2I7013 200 1 2 20.0J7013 200 3 2 12.3F7013 230 3 2 10.8G7013 460 3 2 5.5

BA7013 575 3 2 4.5

71 & X71 Grinder SeriesE7110 230 1 3 23.6J7110 200 3 3 17.3F7110 230 3 3 15.1G7110 460 3 3 7.5

BA7110 575 3 3 6.0E7111 230 1 5 28.0J7111 200 3 5 20.7F7111 230 3 5 18.0G7111 460 3 5 9.0

BA7111 575 3 5 7.2J7112 200 3 7.5 25.3F7112 230 3 7.5 22.0G7112 460 3 7.5 11.0

BA7112 575 3 7.5 9.0

69 HD SeriesF6920 230 3 20 52.6G6920 460 3 20 26.3F6921 230 3 25 62.8G6921 460 3 25 31.4F6923 230 3 30 74.6G6923 460 3 30 37.3F6924 230 3 40 99.2G6924 460 3 40 49.6F6925 230 3 50 128.0G6925 460 3 50 64.0F6926 230 3 60 142.0G6926 460 3 60 71.0F6927 230 3 75 174.0G6927 460 3 75 87.0F6928 230 3 100 232.0G6928 460 3 100 116.0

Electrical Data(Control Panels Available Upon Request)

®

About the Zoeller FAmily oF WAter SolutionS

Founded in 1939, Zoeller Company is one of the oldest independently-owned professional pump manufacturers in North America. Headquartered in Louisville, Kentucky USA, Zoeller has over 800 employees worldwide and close to 600,000 sq. ft. of manufacturing facilities from our seven operations in North America and Asia.Zoeller Company has established itself as an innovative leader in pumping equipment and water treatment systems by continuous research and development. The quality of our products is demonstrated by UL, CSA, CE, and NSF listings as well as continued growth throughout the United States, Canada, Mexico, and over 40 other countries around the globe. The company has also expanded to include five brands, which have become the foundation of Zoeller.

The original Zoeller product line now resides in Zoeller Pump Company, which offers a broad range of submersible pumps from fractional to 7-1/2 HP for residential and commercial sump, effluent, dewatering and grinding applications.Flint & Walling, founded in 1866 in Kendallville, Indiana USA, is the only pump company in the U. S. to manufacture its own motor for jet and centrifugal pumps. This product line specializes in deep well pumps that range from 5 GPM to 1,000

GPM, as well as centrifugal, jet, booster, and submersible pumps up to 7-1/2 HP.Founded in 1952, Wolf Pump is a manufacturer of submersible turbine pumps located in Abernathy, Texas. Wolf currently produces 4” to 8” pumps with capacities ranging from 35 to 1000 GPM. These pumps are known for their efficiency and

durability in demanding water applications including irrigation, municipal water supplies, dewatering applications, dairy production, mining, the oil and gas industries, aquaculture, and more.

Zoeller Engineered Products provides products for storm water removal, sewage pumping stations and

hazardous environment applications for residential, commercial and municipal markets. Available from 1/2 BHP to 100 BHP, each pump is customized by design, manufacture and installation according to exact application needs.

Clarus Environmental offers sustainable environmental products, solutions, and

services for the collection, treatment, and dispersal of residential and community wastewater. This line specializes in onsite pumps, pressure sewers, biological and mechanical treatment processes, disinfection, and discharge of safe water.

SECTION: Z0.00.050ZM11910218Supersedes1117

3649 Cane Run Road • Louisville, KY 40211 • 502-778-2731 • 1-800-928-7867 • zoellerengprod.com

Pumps and Systems - Zoeller Engineered Products · Pumps and Systems Commercial Duty Pumps ... From...

Documents

Transcript of Pumps and Systems - Zoeller Engineered Products · Pumps and Systems Commercial Duty Pumps ... From...