Pump Controller - Teledyne ISCO · 2019. 6. 28. · Pump Controller For D-Series Syringe Pumps...
2
Pump Controller For D-Series Syringe Pumps Operating Modes: • Constant flow or pressure with up to four pumps • Gradient LC programming • Flow or pressure programming with a single pump • Dispense Mode Standard Features: • Easy operation with “Smart Key” programming • Remote installation up to 50 feet away • 4 Pump operation Computer Control Pump operation by computer control is available to access Start/Stop and set point for pressure or flow. Standard control interfaces include: • USB/RS232 Serial • 0–10Vdc, 0–5Vdc & -5 to +5Vdc Inputs • RS485/Ethernet—Modbus RTU Optional interfaces include: • 0–10Vdc, 0–5Vdc & -5 to +5Vdc Outputs • 4–20 mA inputs and outputs Precision control that you demand! EASY TO USE Most D-Series pumps, regardless of configuration or operating mode, utilize the same controller, which can be operated up to 50 feet from the pump modules with optional extension cables. “Smart key” programming makes setting up and running your pump system easy and can be learned in just a few minutes. Multiple pumps can be controlled with a single program, a configured program, or independently with varied programs. With complete front panel function and front panel accessability, status, flow rate, and pressure parameters are continuously displayed. ONE CONTROLLER OPERATION Up to four pumps can be operated with one “Smart key” controller. The possible configurations, as displayed below, are: single, dual, three, or four pump. Single pump—constant flow, constant pressure, or dispensing mode Dual pump—continuous constant flow oar pressure or two pump independent modes Three pump—independent constant flow or pressure or one dual pump mode Four pump—independent constant flow or pressure with two dual pump systems or four pump independent modes One controller can operate up to four pumps.
Transcript of Pump Controller - Teledyne ISCO · 2019. 6. 28. · Pump Controller For D-Series Syringe Pumps...
-
Pump Controller For D-Series Syringe Pumps
Operating Modes:• Constant flow or pressure with up
to four pumps• Gradient LC programming• Flow or pressure programming
with a single pump• Dispense Mode
Standard Features:• Easy operation with “Smart Key”
programming
• Remote installation up to 50 feet away
• 4 Pump operation
Computer ControlPump operation by computer control is available to access Start/Stop and set point for pressure or flow.
Standard control interfaces include:
• USB/RS232 Serial
• 0–10Vdc, 0–5Vdc & -5 to +5Vdc Inputs
• RS485/Ethernet—Modbus RTU
Optional interfaces include:
• 0–10Vdc, 0–5Vdc & -5 to +5Vdc Outputs
• 4–20 mA inputs and outputs
Precision control that you demand!EASY TO USEMost D-Series pumps, regardless of configuration or operating mode, utilize the same controller, which can be operated up to 50 feet from the pump modules with optional extension cables. “Smart key” programming makes setting up and running your pump system easy and can be learned in just a few minutes. Multiple pumps can be controlled with a single program, a configured program, orindependently with varied programs. With complete front panel function and front panel accessability, status, flow rate, and pressure parameters are continuously displayed.
ONE CONTROLLER OPERATIONUp to four pumps can be operated with one “Smart key” controller.The possible configurations, as displayed below, are: single, dual,three, or four pump.
Single pump—constant flow, constant pressure, or dispensing mode
Dual pump—continuous constant flow oar pressure or two pump independent modes
Three pump—independent constant flow or pressure or one dual pump mode
Four pump—independent constant flow or pressure with two dual pump systems or four pump independent modes
One controller can operate up to four pumps.
-
L-7137 Rev 3.0 06/19
Teledyne ISCOP.O. Box 82531, Lincoln, Nebraska, 68501 USAToll-free: (800) 228-4373 • Phone: (402) 464-0231 • Fax: (402) 465-3091 teledyneisco.comTeledyne ISCO is continually improving its products and reserves the right to change product specifications, replacement parts, schematics, and instructions without notice.
ORDERING INFORMATIONDESCRIPTION PART NO.
Syringe Pump Controller ................................................. 68-1240-026
RS-232 Cable (9-pin sub D to 25-pin sub D extension) .... 480-7996-00
10 ft. Extension Cable ...................................................... 68-1020-210
50 ft. Extension Cable ...................................................... 68-1020-214
USB Cable (USB Type A to 25 pin Sub D plug ................. 68-1247-504
Ethernet Cale (Ethernet RJ45 to 25 pin Sub D plug ......... 68-1247-505
CONTROLLER SPECIFICATIONSSize (H x W x D): 5.4 x 10.7 x 12 inches (13.59 x 27.18 x 30.48 cm)
Weight: 6.5 lbs (2.96 kg)
KEY CONTROLLER FUNCTIONS
Program Gradient: Puts pump in gradient mode and accesses gradient programming.
Constant Pressure: Puts pump in constant pressure mode.
Constant Flow: Puts pump in constant flow rate mode.
Rapid Pressure: Allows rapid pressurization to the stable pressure point.
Accessory Control: Manually operates accessories such as valves.
Stop: Stops the drive motor.
Dispense Mode: Activates Dispense Mode.
Refill: Pump drive motor moves piston downward at a programmed rate.
Hold: Freezes the program clock. The unit will continue at the current gradient parameters.
Recall: Replaces current gradient program with one recalled from nonvolatile memory.
Clear Entry: Clear the last digit entered from the numeric key.
Store: Stores current gradient program in nonvolatile memory.
Zero Pressure: Sets pressure display to zero. Active only from -750 to +750 psi.
Run: Turns on pump driver motor to move piston upward.
Menu: Provides access to operational modes, units and optional parameters.
Limits: Enables changes to maximum and minimum pressure and flow limits.
A, B, C, D: Soft keys used to select display options
CPa 0.0000mL/MIN 255$$PSI 000.00mLSTOPPED 00:00:1665000PSIPRESSURE
1. Connection for Pump A 2. Connection for Pump B 3. Connection for Pump C 4. Connection for Pump D 5. Chassis Ground 6. Serial Number Tag 7. Digital I/O (optional) 8. 4-20 mA Outputs (optional) 9. USB/Ethernet 10. RS 232/485 Connections 11. Accessory I/O Connections
1
2
3
4567
8
9
10
11
CONTROLLER CONNECTIONS
