PT-1800Book - Brother Industriesdownload.brother.com/pub/com/ptouch-pdf/UM_PT1800.pdf ·...
Transcript of PT-1800Book - Brother Industriesdownload.brother.com/pub/com/ptouch-pdf/UM_PT1800.pdf ·...
USER’S GUIDE• Read this User’s Guide before you start using your P-touch.• Keep this User’s Guide in a handy place for future reference.
1800/1810
INTRODUCTION
Thank you for purchasing the P-touch 1800/1810!
Your new P-touch will allow you to create labels and stamps for any need. Its versatilityenables you to design custom labels by choosing from a variety of frame designs and frommany characters sizes and styles. In addition, the four tape widths (1/4” (6 mm), 3/8” (9mm), 1/2” (12 mm), and 3/4” (18 mm)) and variety of tape colors allow you to print per-sonalized labels, useful for color-coded filing. With the
Stamp
function, you can quicklyand easily make stamps for reusable pre-inked stamp holders.
You no longer have to worry about urgent tasks that require professional printing. In theoffice, the factory, the lab and the home, the quality and performance of the P-touch1800/1810 makes it an extremely practical machine.
Finally, as you may want to refer to this User’s Guide occasionally, we suggest that youkeep it in a handy place.
(The PT-1800 and the PT-1810 models are equipped with the same functions; however,only the PT-1810 is available with a carrying case.)
FCC NOTICEThis equipment has been tested and found to comply with the limits for a Class B dig-ital device, pursuant to Part 15 of the FCC Rules. These limits are designed to providereasonable protection against harmful interference in a residential installation. Thisequipment generates, uses, and can radiate radio frequency energy and, if not in-stalled and used in accordance with the instructions, may cause harmful interferenceto radio communications. However, there is no guarantee that interference will notoccur in a particular installation. If this equipment does cause harmful interferenceto radio or television reception, which can be determined by turning the equipmentoff and on, the user is encouraged to try to correct the interference by one or moreof the following measures:-Reorient or relocate the receiving antenna-Increase the separation between the equipment and receiver.-Connect the equipment into an outlet on a circuit different from that to which thereceiver is connected.-Consult the dealer or an experienced radio/television technician for help.
Patent numbers and patent publication numbers which are related to this productare as below:USP4839742 USP4983058 USP5120147USP4927278 USP5009530USP4976558 USP5069557
i
CONTENTS
Getting Started
GENERAL DESCRIPTION..................................................................................... 2
GENERAL PRECAUTIONS ................................................................................... 4
BATTERIES........................................................................................................... 5
OPTIONAL AC ADAPTOR .................................................................................. 6
TAPE CASSETTE................................................................................................... 7
ATTACHING LABELS........................................................................................... 8
PRINT HEAD & ROLLERS .................................................................................... 9
Learning the Ropes
DOOR LABEL EXAMPLE.................................................................................... 12
ADDRESS LABEL EXAMPLE ............................................................................... 16
For Your Information
POWER KEY ...................................................................................................... 24
CURSOR KEYS................................................................................................... 25
CODE, ALT & SHIFT KEYS................................................................................. 27
SPACE KEY ........................................................................................................ 30
RETURN KEY..................................................................................................... 31
TAB FUNCTION................................................................................................ 32
DELETE KEY....................................................................................................... 34
LINE OUT FUNCTION ...................................................................................... 35
CLEAR FUNCTION............................................................................................ 36
ACCENT FUNCTION......................................................................................... 39
SYMBOL FUNCTION ........................................................................................ 41
AUTO FORMAT FUNCTION............................................................................. 43
STAMP FUNCTION........................................................................................... 45
SIZE & WIDTH FUNCTIONS............................................................................. 49
STYLE FUNCTION............................................................................................. 53
UNDERLINE FUNCTION................................................................................... 56
FONT FUNCTION............................................................................................. 57
FRAME FUNCTION........................................................................................... 59
ii
TAPE MARGIN FUNCTION............................................................................... 61
HORIZONTAL ALIGNMENT FUNCTION.......................................................... 63
MIRROR PRINTING FUNCTION....................................................................... 64
LENGTH FUNCTION ........................................................................................ 65
PRINT KEY & FEED FUNCTION ........................................................................ 67
NUMBERING FUNCTION................................................................................. 68
REPEAT PRINTING FUNCTION......................................................................... 70
MEMORY FUNCTIONS..................................................................................... 72
TROUBLESHOOTING....................................................................................... 76
ERROR MESSAGE LIST ...................................................................................... 77
SPECIFICATIONS............................................................................................... 81
ACCESSORIES.................................................................................................... 82
2
GENERAL DESCRIPTION
TOP VIEW
BOTTOM VIEW
Tape compartmentcover
LCD displayKeyboard
Tape cutter lever
AC adaptorconnector
Tape exit slot
Battery compartment cover
3
KEYBOARD & LCD DISPLAY
FrameUnderline
Length
Auto
Font 1 Font 2
¡
¿ é ú "
Ç ç Ñ ñ - '
ü í ó á
Alt
Feed
Tab
Caps
Mirror
Font Size Width Style Underline Frame
Memory
Line out Clear
Symbol Accent
Tab Length Tape Align Length A.Format Stamp Repeat Number
Home
End
Store Recall M.Del
Off
Space
A S D F G H J K L :;
Z X C V B N MShift /,
?.
Q W E R T Y U I O P
!1 2
@ # $ % ¢3 4 5 6
& * ( ) 7 8 9 0 Del
PrintOn
Code
Power key
Return key
Cursor keys
Delete key
4
GENERAL PRECAUTIONS
• Use only Brother TZ tapes with this machine. Do not use tapes that do not have the mark.
• Do not pull on the tape being fed from the P-Touch. This may damage the tape cas-sette.
• Do not use the machine in dusty places, and keep it out of both direct sunlight andrain.
• Do not expose the machine to high temperatures or high humidity. Never leave it onthe dashboard or in the back of your car.
• Do not leave any rubber or vinyl on the machine for an extended period of time.Doing so may cause staining.
• Do not clean the machine with alcohol or other organic solvents. Use a soft, drycloth only.
• Do not put any foreign objects into or anything on the machine.
• To avoid injuries, do not touch the cutter’s edge.
• Use only the AC adaptor (model AD-60) designed exclusively for this machine. Useof any other adaptor will void the warranty.
• Do not try to disassemble the AC adaptor.
• When the machine is not being used for a long period of time and it is not necessaryto keep the text files stored in the memory, disconnect the AC adaptor, and removethe batteries to prevent them from leaking and damaging the machine.
• When the AC adaptor is connected, unplugging the adaptor from the electrical outletbefore unplugging it from the machine can delete all text files in the memory, even ifbatteries are installed.
• Use six AA alkaline batteries in this machine.
5
BATTERIES
This lightweight and portable machine can be used anywhere by installing six (6)
AAalkaline batteries
. When you change the batteries, always replace all six at the sametime.
To change the batteries:
1
Remove the battery compartment cover on the back of the machine.
2
If batteries are already installed, remove them.
3
Insert six new AA alkaline batteries, making sure that they face the correct direction.
4
Attach the battery compartment cover.
☞
Be sure to insert the new batteries within five minutes of removing the oldones, otherwise the text shown in the display and any text files stored in thememory will be lost (unless the machine is plugged into an AC outlet withthe AC adaptor).Remove the batteries and disconnect the AC adaptor if you do not intend touse this machine for an extended period of time. When the power is discon-nected, all text shown in the display and stored in the memory will be lost.If alkaline batteries are not used, large fonts cannot be printed.
6
OPTIONAL AC ADAPTOR
The AC adaptor (model AD-60) allows you to use this machine wherever there is an elec-trical outlet.
To connect the optional AC adaptor:
1
Insert the plug on the adaptor cord into the connector marked DC IN 9.5V on theright side of the machine.
2
Insert the plug on the adaptor into the nearest standard electrical outlet.
☞
Only use the AC adaptor designed exclusively for this machine.Remove the batteries and disconnect the AC adaptor if you do not intend touse this machine for an extended period of time. When the power is discon-nected, all text shown in the display and stored in the memory will be lost.When the AC adaptor is connected, unplugging the adaptor from the electri-cal outlet before unplugging it from the machine can delete all text files inthe memory, even if batteries are installed.It is recommended that you use the AC adaptor when printing large fonts on 3/4
″
(18-mm)-wide tape since this operation can quickly drain the batteries.
7
TAPE CASSETTE
A single TZ tape cassette is supplied with this unit. However, since TZ tape cassettes areavailable for this machine in a wide variety of colors and sizes, it is possible to make dis-tinctive color-coded and stylized labels.
In addition, this machine has been designed to allow you to change the tape cassettesquickly and easily.
To change the tape cassette:
1
Lift open the tape compartment cover. The installed cassette is also released.
2
If a tape cassette is already installed, remove it by pulling it straight up.
3
If the ink ribbon in the other tape cassette is loose, use your finger to wind thetoothed wheel in the direction of the arrow on the cassette until there is no slack inthe ribbon. Also, make sure that the end of the tape feeds under the tape guides.
☞
If you are using a new tape cassette provided with a stopper, be sure toremove the stopper.
4
Insert the tape cassette firmly into the tape compartment, making sure that the entireback of the cassette touches the bottom of the compartment.
☞
When inserting the tape cassette, make sure that the inner ribbon does notcatch on the corner of the metal guide.
5
Close the compartment cover, then turn on the machine if it is off.
6
Hold down and press once to advance the tape and remove any
slack.
7
Push down on the tape cutter lever to cut off any excess tape.
Feed
8
ATTACHING LABELS
LAMINATED TAPE
The enclosed stick enables you to easily remove the backing from labels printed on lami-nated tapes.
1
Hold the tape in your left hand, with the printed surface facing up, and hold thestick in your right hand.
2
Pass the tape halfway through the long narrow hole in the stick.
3
Turn the stick three-quarters of a turn towards you and pull the stick away from youas shown below.
4
Peel off the label backing.
FABRIC TAPE
Fabric tape is used to attach a piece of fabric printed with your text onto garments usingan iron. After printing the text onto fabric tape and cutting off the label using scissors,place the label on an ironed garment at the location where you wish to attach it in such away that the printed text can be read correctly. Cover the label with another piece ofcloth and use an iron set to a medium-high temperature (320 to 356 ˚F (160 to 180 ˚C)) topress down firmly for 10 to 15 seconds. For more details, refer to the instructionsincluded with the fabric tape cassette.
STAMP TAPE
Refer to pages 45 through 48 for a detailed explanation on using the stamp tape to makestamps.
GH
ABCDEF
ABCDEF
9
PRINT HEAD & ROLLERS
Occasionally, specks of dust or dirt become attached to the machine’s print head androllers. This is particularly likely when you are using the unit outdoors or in a very dustyenvironment. If a section of the print head is covered with dust, a blank horizontal streakmay appear through the label text. Therefore, as with a tape recorder, the machine’s headmay need to be cleaned from time to time.
To clean the print head and rollers:1 Turn off the machine.
2 Open the tape compartment cover, then remove the tape cassette if one is installed.The print head and rollers are located in the tape compartment.
3 Print head: Use a dry cotton swab to gently wipe the print head with an up-and-down motion.Rollers: Use a dry cotton swab to wipe each roller with an up-and-down motionwhile rotating them with your finger.
4 Install a tape cassette, close the tape compartment cover, and then try printingagain.
5 If dust still remains, repeat steps 3 and 4 using a cotton swab dipped in isopropyl(rubbing) alcohol.
If none of the above works, contact your service representative.
Print headPrint head
Rollers Cotton swab
12
DOOR LABEL EXAMPLE
After you have inserted the batteries and the enclosed tape cassette as explained in theGetting Started chapter, let’s practice using some of the basic functions of your P-touch.We must first begin by turning on the power to the machine.
The underline in the LCD display is called the “cursor”. It is like a pointer which showsyour current position and lets you select characters in your text.
The text you create may sometimes be longer than the 11 characters that the LCD displaycan show at one time. Therefore, the cursor can be moved to show other parts of the text.
Pressing the left cursor key ( ) moves the cursor to the left so that the left side of the
text can be seen and pressing the right cursor key ( ) moves the cursor to the right
so that the right side of the text can be seen.
Some format settings are shown by the triangular and square indicators around the edgeof the display. The default settings (the selected settings when the power is turned on forthe very first time) have been pre-programmed into the machine and represent the mostcommon settings for labels. However, you can design your own label to have any formatthat you wish. Detailed explanations of the formats can be found on pages 64 through 66.
Now, let’s enter the text for our first example, the simple door label shown below.
☞ The label in this example was made using the enclosed 1/2″ (12-mm)-wide tape.
To turn on the machine:
1 Press in the top right-
hand corner of the keyboard.
1: _A B C D E F G H I J K LAlt
Caps FrameUnderline
Length
Auto
Font 1 Font 2
13
ENTERING THE TEXTSince all of the text will be in capital letters, we will use the Caps mode, which allows us
to type capital letters continuously without holding down .
Then, let’s type in the text in the same way that you would type on a typewriter or a com-puter keyboard.
Also like on a typewriter or computer keyboard, the Space key ( ) allows you toadd blank spaces to the text.
☞ The Space key ( ) is different from the right cursor key ( ), which
moves the cursor through the entered text without adding blank spaces.
To enter Caps mode:
2 Hold down and press
once. The Caps indicator
on the left side of the displaylights up.
To type in “MEETING”:
3 Press once and
twice, then press , ,
and once each.
☞ All letters are automaticallyentered as capital letters.
Caps
1: _A B C D E F G H I J K LAlt
Caps FrameUnderline
Length
Auto
Font 1 Font 2
Caps
Tape
Length Repeat
1: M E E T I N G _A B C D E F G H I J K LAlt
Caps FrameUnderline
Length
Auto
Font 1 Font 2
Feed
Feed
14
Type the second word, “ROOM”, to finish the text.
Now that we are finished entering capital letters, we can exit Caps mode.
Once you have entered the text, you can easily edit it by correcting mistakes or simply adjust-ing it or its format. For detailed explanations of text editing methods, see pages 34 to 38.
To add a space:
4 Press .
To type in “ROOM”:
5 Press once, twice,
then once.
☞ Since the text is longer than theLCD display, “ME” moves off thedisplay to the left.
To exit Caps mode:
6 Hold down and press
once. The Caps indicator
goes off.
1: M E E T I N G _A B C D E F G H I J K LAlt
Caps FrameUnderline
Length
Auto
Font 1 Font 2
Feed
1: E T I N G R O O M _A B C D E F G H I J K LAlt
Caps FrameUnderline
Length
Auto
Font 1 Font 2
Align Number
Caps
1: E T I N G R O O M _A B C D E F G H I J K LAlt
Caps FrameUnderline
Length
Auto
Font 1 Font 2
15
PRINTING THE TEXTSeveral format settings are available, however, in this example we will use the default set-tings pre-programmed into the machine and print out our label.
To print the door label:
7 Press once. The message
“COPIES 1/1” appears while thelabel is being printed.
To cut off the door label:
8 Push down on the tape cutterlever.
1 / 1C O P I E SAlt
Caps FrameUnderline
Length
Auto
Font 1 Font 2
Mirror
16
ADDRESS LABEL EXAMPLE
While making the multi-line address label in this example, we will learn how to createmore decorative labels using the various format settings.
☞ Three-line labels, such as this address label, can only be printed on either 1/2”(12-mm)- or 3/4” (18-mm)-wide tape.
Before entering the new text, we must first erase the text shown in the display from theprevious time that the machine was used. When clearing the display, we can choosewhether to erase all of the text and return all format functions (Font, Size, Width, Style,Underline, Frame, Tape margin, Alignment, and Length) to their default settings or just toerase the text.
To erase all of the text and reset the format functions:
1 Hold down and press
once.
2 Press or until
TEXT&FORMATS is selected,
and then press .
Alt
Caps FrameUnderline
Length
Auto
Font 1 Font 2
T E X T & F O R M A T ST E X T O N L Y
Clear
1: _A B C D E F G H I J K LAlt
Caps FrameUnderline
Length
Auto
Font 1 Font 2
HomeEnd
17
ENTERING THE TEXTLet’s begin by typing in the first row of text, the name “Bill Reynolds”.
In a multi-line label, the return key ( ) is used to end one line and start the next
one. The return mark ( ) indicates the end of the line.
To type in “Bill Reynolds”:
3 Hold down and press
once, then release . Press
once, then twice.
4 Press .
5 Type in “Reynolds”.☞ Again, the text is longer than the
LCD display. So “Bil” moves offthe display to the left.
To end the first line and begin another one:
6 Press .
1: B i l l _O K T OAlt
Caps FrameUnderline
Length
Auto
Font 1 Font 2
Caps
Caps
Repeat
1: B i l l _O K T OAlt
Caps FrameUnderline
Length
Auto
Font 1 Font 2
Feed
1: 1 R e y n o l d s _O K T OAlt
Caps FrameUnderline
Length
Auto
Font 1 Font 2
2: _1: B i l l R e y n o lAlt
Caps FrameUnderline
Length
Auto
Font 1 Font 2
18
Now, we can enter the address: 29 South Main St.; Los Angeles, CA 88888.
FORMATTING THE TEXTNow the text has been entered entered as we wish. If it were printed, the standard defaultsettings would be used. The text would be aligned on the left side with 1″ (25 mm) mar-gins and would not be framed or underlined. In addition, the characters would be auto-sized (Auto) and printed using the HELSINKI font (Font1) and NORMAL style settings. Formore details concerning format settings, please see pages 56 and 73.
For this label, though, let’s assume we want a different style of text: BRUSSELS font(Font2), framed, and printed with NARROW (1/6” (4 mm)) tape margins. Therefore, wemust change the format.
To type in the address:
7 Type “29 South Main St.”, then
press .
8 Type “Los Angeles, CA 88888”.
To select the BRUSSELS font setting:
9 While holding down ,
press once, and keep
held down to display the
current font setting.
3: _2: 2 9 S o u t h M aAlt
Caps FrameUnderline
Length
Auto
Font 1 Font 2
3: , C A 8 8 8 8 82: i n S t .Alt
Caps FrameUnderline
Length
Auto
Font 1 Font 2
H E L S I N K IF O N TAlt
Caps FrameUnderline
Length
Auto
Font 1 Font 2
Font
19
0 While still holding down
, continue pressing
until BRUSSELS is dis-
played, and then release
.
To select the ROUND frame setting:
A While holding down ,
press once, and keep
held down to display the
current frame setting.
B While still holding down ,
continue pressing until
ROUND is displayed, and then
release .
To select the NARROW tape margin setting:
C While holding down ,
press once, and keep
held down to display the
current tape margin setting.
D While still holding down
, continue pressing
until NARROW is displayed, and
then release .
B R U S S E L SF O N TAlt
Caps FrameUnderline
Length
Auto
Font 1 Font 2
Font
O F FF R A M EAlt
Caps FrameUnderline
Length
Auto
Font 1 Font 2
Frame
R O U N DF R A M EAlt
Caps FrameUnderline
Length
Auto
Font 1 Font 2
Frame
F E E DF U L L
Alt
Caps FrameUnderline
Length
Auto
Font 1 Font 2
Tape
F E E DN A R R O W
Alt
Caps FrameUnderline
Length
Auto
Font 1 Font 2
Tape
20
Different format settings can be chosen either before or after the text is entered. The pro-cedure shown above can be used to change the other format settings.
PRINTING THE TEXTIf we want only one copy of the text, we could just press to print it. However,let’s assume that we have three letters onto which we wish to attach address labels.Therefore, we need to print three copies of the same text.
To print three copies of the label:
E Hold down and press
once.
F Press .
G Press . The number of each copy is displayed while it is being
printed.
Mirror
U N T I L 1 – 9 ?C O P I E SAlt
Caps FrameUnderline
Length
Auto
Font 1 Font 2
Repeat
U N T I L 3C O P I E SAlt
Caps FrameUnderline
Length
Auto
Font 1 Font 2
Width
1 / 3C O P I E S
2 / 3C O P I E S
3 / 3C O P I E SAlt
Caps FrameUnderline
Length
Auto
Font 1 Font 2
Alt
Caps FrameUnderline
Length
Auto
Font 1 Font 2
Alt
Caps FrameUnderline
Length
Auto
Font 1 Font 2
21
With these examples, we have covered many of the basic features of your P-touch so thatyou can begin creating your own customized labels. If you have any questions about anyof the functions or keys, refer to the appropriate explanation in the following section.
H Push down on the tape cutter lever to cut the tape, then use scissors to cutalong the cutting guide to separate the labels.
✂ ✂
24
POWER KEY
The power key ( ) is located in the top right-hand corner of the keyboard. If bat-
teries have been installed or the machine has been plugged in using the optional ACadaptor, the previous session’s information is displayed when the machine is turned on.This feature allows you to stop work on a label, turn off the machine, and return to it laterwithout having to re-enter the text.
The machine will automatically turn off if no key is pressed within 5 minutes. Themachine’s internal memory stores the current session’s information and displays it whenyou turn on the machine again.
To turn on the machine:
● Press . The previous session’s information appears in the LCD display.
To turn off the machine:
● Press . The current session’s information is stored in the internal memory.
25
CURSOR KEYS
The machine’s LCD display shows two rows of 11 characters; however, the text that youcreate can be up to 99 characters long. You can review and edit your text by using thecursor keys to move the cursor so that different parts are shown in the display.
LEFT CURSOR KEY
To move the cursor one character to the left:
● Press once.
To move the cursor several characters to the left:
● Hold down until the cursor moves to the desired position.
To move the cursor to the beginning of the current line:
● Hold down and press .
RIGHT CURSOR KEY
To move the cursor one character to the right:● Press once.
To move the cursor several characters to the right:● Hold down until the cursor moves to the desired position.
To move the cursor to the end of the current line:
● Hold down and press .
26
UP CURSOR KEY
To move the cursor up to the previous line:
● Press once.
☞ If the cursor is in the first line of text, it will move to the beginning of the line.To move the cursor up several lines:
● Hold down until the cursor moves to the desired position.
To move the cursor to the beginning of the entire text:
● Hold down and press .
DOWN CURSOR KEY
To move the cursor down to the following line:
● Press once.
☞ If the cursor is in the last line of text, it will move to the end of the line.To move the cursor down several lines:
● Hold down until the cursor moves to the desired position.
To move the cursor to the end of the entire text:
● Hold down and press .
Home
Home
Home
End
End
End
27
CODE, ALT & SHIFT KEYS
Most characters can be entered simply by pressing their keys. However, to use specialfunctions or to enter capital letters, accented characters and some symbols, the followingspecial keys are necessary.
CODE KEY
To use a function printed above a key:
● Hold down and press the key immediately below the desired function.
EXAMPLE
To start the Symbol function:
● Hold down and press
once.
1: A B C _A B C D E F G H I J K LAlt
Caps FrameUnderline
Length
Auto
Font 1 Font 2
1: A B C _Ü Æ æ Ã ã Ë ë Õ õ ° ™Alt
Caps FrameUnderline
Length
Auto
Font 1 Font 2
Symbol
28
ALT KEY
To type in characters printed in color on the right-hand side of the keys:
● Hold down and press the key of the desired character written in color. The Alt
indicator on the left side of the display lights up while is held down.
EXAMPLE
To type in “–”:
● Hold down and press once. The Alt indicator lights up while
is held down.
Symbol
Symbol
Symbol
Symbol
1: 0 1 2 _L E N G T H i n c h
1: 0 1 2 - _L E N G T H i n c hAlt
Caps FrameUnderline
Length
Auto
Font 1 Font 2
Alt
Caps FrameUnderline
Length
Auto
Font 1 Font 2
29
SHIFT KEY
To type in a capital letter or a symbol printed in the top left-hand corner of a key:
● Hold down and press the key of the desired letter or symbol.
EXAMPLE
The Caps mode is similar to holding down . It allows you to type capital letters con-tinuously.
To type in many capital letters:
1 Hold down and press . The Caps indicator on the left side of the dis-
play lights up.
2 Press the keys of the desired letters or symbols.
3 To exit Caps mode, hold down and press . The Caps indicator goes off.
To type in “%”:
● Hold down and press .
Caps
1: 5 _A B C D E F G H I J K LAlt
Caps FrameUnderline
Length
Auto
Font 1 Font 2
1: 5 % _A B C D E F G H I J K LAlt
Caps FrameUnderline
Length
Auto
Font 1 Font 2
Caps Underline
Caps
Caps
1: _A B C D E F G H I J K LAlt
Caps FrameUnderline
Length
Auto
Font 1 Font 2
Caps
30
SPACE KEY
The Space key ( ) lets you add blank spaces between characters in your text. It is
different from the right cursor key ( ), which just moves the cursor without adding
blank spaces.
To add a space:
● Press .
EXAMPLE
To add a space:
● Press .
Feed
Feed
1: J . _A B C D E F G H I J K LAlt
Caps FrameUnderline
Length
Auto
Font 1 Font 2
1: J . _A B C D E F G H I J K LAlt
Caps FrameUnderline
Length
Auto
Font 1 Font 2
Feed
31
RETURN KEY
Like on a typewriter or word processor, this machine’s return key ( ) is used to
end a line of text and start another one. When you have finished entering one line, pressthe return key to make a new line and move the cursor to it.
☞ A single block can only contain a maximum of three text lines. If you press
when the cursor is located in the third line, the error message “3 LINE
LIMIT!” will appear.
The return key can also be used to select an item from a list (e.g., add a symbol oraccented character to the text) or to apply a selected setting.
Some questions asking you to confirm a command may appear on the LCD display, espe-cially when the function that you have chosen will delete or affect files. In these cases,
pressing is like answering “yes”.
☞ To answer “no”, press . Refer to DELETE KEY on page 34.
To add a new line:
● Press . The return mark ( ) appears to indicate the end of the line.
To select an item from a list:
● Press .
To answer “yes”:
● Press .
Tape widthsMaximum number of
lines that can be printed
1/4” (6 mm) 1
3/8” (9 mm) 2
1/2” (12 mm) 3
3/4” (18 mm) 3
Clear
32
TAB FUNCTION
This function allows you to separate sections of a line of text by adding tabs. This enablesyou to create perfectly aligned columns without having to type in several spaces. All tabshave the same length and are measured from either the beginning of the line or the previ-ous tab if there is more than one. The tab length can be set between 0.0” and 11.8” (0.0and 30.0 cm).
☞ The text can contain no more than 50 tabs. If 50 tabs have already been added to
the text when is pressed, the error message “TAB LIMIT!” appears.
To set the tab length:
1 Hold down and press once. The current tab length is displayed.
2 Press or until the desired length is displayed or use the number keys to
type in the length.
☞ To change the units (inches or centimeters) used to display the tab lengths,
press until the desired units are displayed.
3 Press .
To add a tab:
● Hold down and press once. The tab mark ( ) appears in the text to
indicate the position of the tab.
☞ If the text in front of a tab extends past the point where the next section oftext should start, the text will instead start at the following tab position.For example, if the tab length is set to 2” and the following text is typed in:
Tab
Tab Length
HomeEnd
Tab
2: J K L M N O P Q R S T U1: A B C D E F G H I
33
the label shown below will be printed
EXAMPLE
To set the tab length to 1”:
1 Hold down and press
once.
2 Press until 1.0 is displayed.
3 Press .
To add a tab:
● Hold down and press
once.
J K L M N O P Q R S T UA B C D E F G H I
Margin Tab (2 inch) Tab (2 inch) Margin
Alt
Caps FrameUnderline
Length
Auto
Font 1 Font 2
T A B L E N G T H 2 . 0 i n c h
Tab Length
Alt
Caps FrameUnderline
Length
Auto
Font 1 Font 2
T A B L E N G T H 1 . 0 i n c h
End
Alt
Caps FrameUnderline
Length
Auto
Font 1 Font 2
1: P a r t N o .A B C D E F G H I J K L
Tab
34
DELETE KEY
The delete key ( ) allows you to remove characters to the left of the cursor’s current
position. It differs from the left cursor key ( ), which only moves the cursor without
deleting any characters.
The delete key can also be used to quit most functions and return to the previous displaywithout changing the text.
Some questions asking you to confirm a command may appear on the LCD display, espe-cially when the function that you have chosen will delete or affect files. In these cases,
pressing is like answering “no”.
☞ To answer “yes”, press . Refer to RETURN KEY on page 31.
To delete one character:
1 Press , , or to position the cursor below the character
immediately to the right of the character that you wish to delete.
2 Press once.
To delete a sequence of characters:
1 Press , , or to position the cursor below the character
immediately to the right of the last character that you wish to delete.
2 Hold down until all of the characters that you wish to delete are deleted.
To quit a function without changing your text:
● Press to return to your text.
To answer “no”:
● Press .
Clear
Clear
HomeEnd
Clear
HomeEnd
Clear
Clear
Clear
35
LINE OUT FUNCTION
With the Line Out function, you can easily remove an entire line of text.
To delete a line of text:
1 Press , , or to position the cursor within the line of text that
you wish to delete.
2 Hold down and press once.
☞ Each time is pressed while is held down, one line of text is
deleted.
EXAMPLE
To delete “012-345-6789”:
● Hold down and press
once.
HomeEnd
Line Out
Line Out
Alt
Caps FrameUnderline
Length
Auto
Font 1 Font 2
2: 2 - 3 4 5 - 6 7 8 9 _1: S G a r d e n
Line Out
2: _1: K ´ s G a r d e nAlt
Caps FrameUnderline
Length
Auto
Font 1 Font 2
36
CLEAR FUNCTION
When clearing the display before entering new text, the Clear function can be used tochoose whether all of the text is erased and all format functions (Font, Size, Width, Style,Underline, Frame, Tape margin, Alignment, Tab length, Mirror printing, and Length) arereturned to their default settings, or whether just the text is erased.
To delete all of the text and return all formats to their default settings:
1 Hold down and press .
2 Press or until TEXT&FORMATS is selected (flashing).
☞ To return to the text without erasing anything, press .
3 Press .
EXAMPLE
To clear the text and formats:
1 Hold down and press
.
2 Press until TEXT&FOR-MATS is flashing.
Clear
HomeEnd
Clear
Alt
Caps FrameUnderline
Length
Auto
Font 1 Font 2
2: 2 - 3 4 5 - 6 7 8 9 _1: S G a r d e n
Clear
Alt
Caps FrameUnderline
Length
Auto
Font 1 Font 2
T E X T & F O R M A T ST E X T O N L Y
Home
Alt
Caps FrameUnderline
Length
Auto
Font 1 Font 2
T E X T & F O R M A T ST E X T O N L Y
37
To delete just the text:
1 Hold down and press .
2 Press or until TEXT ONLY is selected (flashing).
☞ To return to the text without erasing anything, press .
3 Press .
EXAMPLE
3 Press .
To clear just the text:
1 Hold down and press
.
Alt
Caps FrameUnderline
Length
Auto
Font 1 Font 2
1: _
Clear
HomeEnd
Clear
Alt
Caps FrameUnderline
Length
Auto
Font 1 Font 2
2: 2 - 3 4 5 - 6 7 8 9 _1: S G a r d e n
Clear
Alt
Caps FrameUnderline
Length
Auto
Font 1 Font 2
T E X T & F O R M A T ST E X T O N L Y
38
2 Press until TEXT ONLY isflashing.
3 Press .
End
Alt
Caps FrameUnderline
Length
Auto
Font 1 Font 2
T E X T & F O R M A T ST E X T O N L Y
Alt
Caps FrameUnderline
Length
Auto
Font 1 Font 2
1: _
39
ACCENT FUNCTION
The Accent function can also be used to add accented characters to your text. Many ofthese characters can also be typed in using the Symbol function.
The accented characters are grouped according to the capital or small letter that they arecombined with. The following accented characters are available:
To type in an accented character:
1 Hold down and press . The message “a – u / A – U?” appears on the
display.
2 Press the key of the letter in the desired accented character.
☞ To type a capital letter, hold down (or hold down and press
to turn on Caps mode) before pressing the letter key.
3 Press or until the desired accented character flashes.
4 Press . The letter and the accent flash alternately in the text.
☞ To type in a series of accented characters, hold down before pressing
. Then, continue adding accented characters by selecting them as
explained in steps 2 and 3, and holding down while pressing
. Press just after selecting the last character in the series.
Letters Accented characters Letters Accented characters
a à á ä â ã å æ I Í Ï Î
A À Á Ä Â Ã Å Æ n ñ
c ç N Ñ
C Ç o ó ö ô õ
e è é ë ê e O Ó Ö Ô Õ
E È É Ë Ê E u ù ú ü û
i í ï î U Ù Ú Ü Û
˜
Accent
Caps
Caps
40
EXAMPLE
To add the accented character “É”:
1 Hold down and press
.
2 Hold down and press
.
3 Press until É flashes.
4 Press .
Accent
1: R E S U M _a - u / A - U ?Alt
Caps FrameUnderline
Length
Auto
Font 1 Font 2
Caps
Tape
1: R E S U M _È É Ë ÊAlt
Caps FrameUnderline
Length
Auto
Font 1 Font 2
1: R E S U M _È É Ë ÊAlt
Caps FrameUnderline
Length
Auto
Font 1 Font 2
1: R E S U M É _
Alt
Caps FrameUnderline
Length
Auto
Font 1 Font 2
41
SYMBOL FUNCTION
In addition to the letters, symbols and numerals on the key tops, there are 53 additionalmarks available with the Symbol function.
The following symbols are available:
To type in a symbol:
1 Hold down and press . A row of symbols appear in the display.
2 Press or to display different rows of symbols and press or
until the desired symbol flashes.
3 Press . The symbol appears in the text.
☞ To type in a series of symbols, hold down before pressing .
Then, continue adding symbols by selecting them as explained in steps 2
and 3, and holding down while pressing . Press just
after selecting the last symbol in the series.
Group Symbol
1 Ü Æ æ Ã ã e Õ õ °
2 + × ÷ = § 2 32 3 4 [ ]
3
4
5
E TM
☞ ☞ R C
♥ ★
Symbol
HomeEnd
42
EXAMPLE
To add the symbol “ ”:
1 Hold down and press
.
2 Press or until the
row containing “ ” appears,
then press or until
“ ” flashes.
3 Press .
Symbol
Alt
Caps FrameUnderline
Length
Auto
Font 1 Font 2
1: D A N G E R _ü Æ æ Ã ã Õ õ • °
HomeEnd
Alt
Caps FrameUnderline
Length
Auto
Font 1 Font 2
1: D A N G E R _R C
Alt
Caps FrameUnderline
Length
Auto
Font 1 Font 2
1: D A N G E R _R C
43
AUTO FORMAT FUNCTION
With the Auto Format function, you can select from a variety of preset formats perfect foryour specific need. This function automatically adjusts the label length, tape margins andholizontal alignment without changing the text or any other formats, allowing you to cre-ate labels faster and easier.
The following preset formats are available:
To select a preset format:
1 Hold down and press once. The currently selected setting appears in
the display.
2 Press or to select the desired setting.
☞ To return to default settings, press .
Auto Format settingLabel length
settingTape margin
settingHorizontal
alignment setting
DEFAULT OFF FULL LEFT
3.5”FLOPPY 2.8” (7.0 cm) NARROW CENTER
5”FLOPPY 4.8” (12.2 cm) NARROW CENTER
VHS SPINE 5.5” (14.0 cm) NARROW CENTER
VHS 3.0” (7.7 cm) NARROW CENTER
VCR8mm CASE 3.6” (9.2 cm) NARROW CENTER
VCR8mm 2.9” (7.3 cm) NARROW CENTER
VHS-C SPINE 1.8” (4.5 cm) NARROW CENTER
VHS-C 2.3” (5.8 cm) NARROW CENTER
AUDIO 3.5” (8.9 cm) NARROW CENTER
DAT CASSETTE 2.2” (5.6 cm) NARROW CENTER
MINI DISK 2.0” (5.2 cm) NARROW CENTER
ORGANIZER L 3.2” (8.2 cm) NARROW CENTER
ORGANIZER S 2.6” (6.5 cm) NARROW CENTER
FILE LONG 7.2” (18.3 cm) NARROW CENTER
FILE SHORT 3.7” (9.4 cm) NARROW CENTER
A.Format
HomeEnd
Feed
44
3 Press to apply the selected setting.
☞ The Length indicator lights up if any setting other than DEFAULT is selected.
EXAMPLE
To select the AUDIO setting:
1 Hold down and press
.
2 Press or until theAUDIO setting is displayed.
3 Press .
A.Format
Alt
Caps FrameUnderline
Length
Auto
Font 1 Font 2
F O R M A T T Y P E ?D E F A U L T
HomeEnd
Alt
Caps FrameUnderline
Length
Auto
Font 1 Font 2
F O R M A T T Y P E ?A U D I O
45
STAMP FUNCTION
The Stamp function allows you to quickly and easily create your own stamp stencil filmsfor customized stamps. Select this function to automatically center the text and adjust thetape length and margins to a perfect format for the pre-inked stamp film holders. Since thestamp holder is reusable, just make a new stamp stencil film and replace the one in theholder.
To make a stamp:1 Type in the text, and then insert a Medium (3/4” (18-mm)-wide) stamp film cassette.
2 Hold down and press once. The message “STAMP FORMAT?”
appears in the display.
3 Press . The text is formatted for a stamp: centered within the preset message
area with the tape length and margins automatically adjusted.
4 Press to cut the text out of the stamp stencil film.
5 Push down on the tape cutter lever, remove the backing paper from the stamp sten-cil film and affix it to the ink pad of a stamp film holder.
EXAMPLE
To cut a stamp:
1 Enter the text and insert a stamp film cassette in the tape compartment.
2 Hold down and press
.
Stamp
Mirror
Stamp
F O R M A T ?S T A M PAlt
Caps FrameUnderline
Length
Auto
Font 1 Font 2
46
3 Press .
4 Press .
5 Push down on the tape cutter lever to cut the stamp stencil film.
To affix a stamp:
6 Remove the stamp frame from around the stamp film holder ink pad, oneside at a time, then remove the protective seal covering the ink pad and thebacking paper from the stamp stencil film.
7 With the glossy side of the stamp stencil film upward, align one of its endswith the slit on the side of the stamp film holder.
2: 1 2 3 4 M a i n S _1: J . S m i t hAlt
Caps FrameUnderline
Length
Auto
Font 1 Font 2
1 / 1C O P I E SAlt
Caps FrameUnderline
Length
Auto
Font 1 Font 2
Mirror
Tape end
Glossy side
Slit
47
8 Hold the end of the stamp stencil film in place with your thumb, then passthe tape through the guides while pulling it tight.
9 Fold the other end of the stamp stencil film over the other side of the stampfilm holder and hold it in place with your finger.
0 Fit the stamp frame over the stamp stencil film and push it into place.
Guides
Fold over
48
A Insert the stamp film holder straight into its cap.
☞ Be sure that the stamp is correctly covered in order to prevent ink spills.
49
SIZE & WIDTH FUNCTIONS
The character size can be adjusted using both the Size and Width functions. Since thecharacter size that can be used depends on the width of the tape, the following tableshows the character sizes that can be used with each tape width.
The default size setting is AUTO and the default width setting is OFF. The currentlyselected size setting is always shown by the indicator above the display.
With the AUTO size setting, the machine compares your text with the width of theinstalled tape and automatically adjusts the characters to the largest possible size. How-ever, six other point sizes are also available and each can be printed in wide characters.
Tape widths Sizes (in points)
1/4” (6 mm) 6, 9, 12
3/8” (9 mm) 6, 9, 12, 18
1/2” (12 mm) 6, 9, 12, 18, 24
3/4” (18 mm) 6, 9, 12, 18, 24, 36
Size setting (in
points)Width function OFF Width function ON
6
9
12
18
50
To change the size setting:
1 While holding down , press once, and keep held down to dis-
play the current size setting.
2 While still holding down , continue pressing until the desired size set-
ting is displayed and is shown by the size indicator.
☞ The current character size setting is also shown by the size indicator abovethe display.
3 Release to apply the selected size setting to the entire text.
☞ With the AUTO setting selected and 3/4” (18-mm)-wide tape installed, textconsisting of just one line of only capital letters will be printed with a charac-ter size of 48 points.
24
36
Size setting (in
points)Width function OFF Width function ON
Size
Size
51
EXAMPLE
To turn on or off the Width function:
1 While holding down , press once, and keep held down to dis-
play the current width setting.
2 While still holding down , continue pressing until the desired width
setting is displayed.
3 Release to apply the selected width setting to the entire text.
To select the 24 point size setting:
1 While holding down ,
press once, and keep
held down.
2 While still holding down ,
continue pressing until 24 is
displayed.
3 Release .
Size
A U T OS I Z EAlt
Caps FrameUnderline
Length
Auto
Font 1 Font 2
Size
2 4S I Z EAlt
Caps FrameUnderline
Length
Auto
Font 1 Font 2
Width
Width
52
EXAMPLE
To turn on the Width function:
1 While holding down ,
press once, and keep
held down.
2 While still holding down ,
continue pressing until ON is
displayed.
3 Release .
Width
O F FW I D EAlt
Caps FrameUnderline
Length
Auto
Font 1 Font 2
Width
O NW I D EAlt
Caps FrameUnderline
Length
Auto
Font 1 Font 2
53
STYLE FUNCTION
You can choose from nine different character styles to apply to your text.
☞ Characters printed using the smaller sizes may be difficult to read if certain stylesettings (e.g., I+SHADOW) are selected.
The following style settings are available:
NORMAL I+BOLD (italic & bold)
BOLD I+OUTLINE (italic & outline)
OUTLINE I+SHADOW (italic & shadow)
SHADOW VERTICAL
ITALIC
The default style setting is NORMAL. The style indicator at the bottom right of the displayshows the current style setting when any setting other than NORMAL is selected.
Refer to Reference at the end of this section for samples of the available settings.
To change the style setting:
1 While holding down , press once, and keep held down to dis-
play the current style setting.
2 While still holding down , continue pressing until the desired style set-
ting is displayed.
☞ The current style setting is shown by the style indicator at the bottom right ofthe display.
3 Release to apply the selected style setting to the entire text.
EXAMPLE
To select the I+SHADOW style setting:
1 While holding down ,
press once, and keep
held down.
Style
Style
Style
N O R M A LS T Y L EAlt
Caps FrameUnderline
Length
Auto
Font 1 Font 2
54
2 While still holding down ,
continue pressing until
I+SHADOW is displayed.
3 Release .
I + S H A D O WS T Y L EAlt
Caps FrameUnderline
Length
Auto
Font 1 Font 2
Style
55
REFERENCE
Fontsetting
Style setting
NORMAL BOLD OUTLINE
HELSINKI
BRUSSELS
Fontsetting
Style setting
SHADOW ITALIC I+BOLD
HELSINKI
BRUSSELS
Fontsetting
Style setting
I+OUTLINE I+SHADOW VERTICAL
HELSINKI
BRUSSELS
56
UNDERLINE FUNCTION
You can emphasize your text by underlining it.
The default underline setting is OFF. When the Underline function is set to ON, theUnderline indicator on the right side of the display lights up.
To turn on or off the Underline function:
1 While holding down , press once, and keep held down to dis-
play the current underline setting.
2 While still holding down , continue pressing until the desired under-
line setting is displayed.
☞ The Underline indicator lights up when the ON setting is selected.
3 Release to apply the selected underline setting to the entire text.
EXAMPLE
ON
To select the ON underline setting:
1 While holding down ,
press once, and keep
held down.
2 While still holding down ,
continue pressing until ON is
displayed.
3 Release .
Underline
Underline
O F FU N D E R L I N EAlt
Caps FrameUnderline
Length
Auto
Font 1 Font 2
Underline
O NU N D E R L I N EAlt
Caps FrameUnderline
Length
Auto
Font 1 Font 2
Underline
57
FONT FUNCTION
With the Font function, you can choose one of two fonts for your text.
The following font settings are available:HELSINKI and BRUSSELS
The default font setting is HELSINKI. The currently selected font setting is always shownby the Font indicators below the display.
Refer to Reference at the end of this section for samples of the available settings.
To change the font setting:
1 While holding down , press once, and keep held down to dis-
play the current font setting.
2 While still holding down , continue pressing until the desired font set-
ting is displayed and is shown by the font indicator.
☞ The current font setting is also shown by the font indicator at the bottom leftof the display.
3 Release to apply the selected font setting to the entire text.
EXAMPLE
To select the BRUSSELS font setting:
1 While holding down ,
press once, and keep
held down.
2 While still holding down ,
continue pressing until
BRUSSELS is displayed.
3 Release .
Font
Font
H E L S I N K IF O N TAlt
Caps FrameUnderline
Length
Auto
Font 1 Font 2
Font
B R U S S E L SF O N TAlt
Caps FrameUnderline
Length
Auto
Font 1 Font 2
Font
59
FRAME FUNCTION
With the Frame function, you can choose from various frames and highlights to design amore decorative or emphasized label.
The following Frame settings are available:OFF, ROUND, CANDY, POINTING, NAMEPLATE, DOT
The default frame setting is OFF; however, other settings are also available. When anysetting other than OFF is selected, the Frame indicator on the right side of the displaylights up.
Refer to Reference at the end of this section for samples of the available settings.
To change the frame setting:
1 While holding down , press once, and keep held down to dis-
play the current frame setting.
2 While still holding down , continue pressing until the desired frame
setting is displayed.
☞ The Frame indicator lights up when any setting other than OFF is selected.
3 Release to apply the selected frame setting to the entire text.
EXAMPLE
To select the CANDY frame setting:
1 While holding down ,
press once, and keep
held down.
2 While still holding down ,
continue pressing until
CANDY is displayed.
3 Release .
Frame
Frame
O F FF R A M EAlt
Caps FrameUnderline
Length
Auto
Font 1 Font 2
Frame
C A N D YF R A M EAlt
Caps FrameUnderline
Length
Auto
Font 1 Font 2
Frame
60
REFERENCEREFERENCE
Frame setting
Frame sampleFrame setting
Frame sample
OFFPOINT-
ING
ROUNDNAME-PLATE
CANDY DOT
61
TAPE MARGIN FUNCTION
The Tape margin function allows you to adjust the size of the margins on the left and rightsides of your text.
The default tape margin setting is FULL; however, three other settings are also available.
☞ After printing a label using the NONE tape margin setting, hold down and
press once to feed the tape before pushing down on the tape cutter lever
to cut it. Otherwise some of the printed characters may be cut off.After printing using the NARROW and HALF tape margin settings, push down onthe tape cutter lever to cut off the label, then use scissors to cut along the printeddots (:) to center the text within the label.
To change the tape margin setting:
1 While holding down , press once, and keep held down to dis-
play the current tape margin setting.
2 While still holding down , continue pressing until the desired tape
margin setting is displayed.
3 Release to apply the selected tape margin setting to the entire text.
FULL(1” (25 mm margins))
NONE(no margins)
NARROW(1/6” (4 mmmargins))
HALF(1/2” (12 mmmargins))
Feed
Tape
Tape
62
EXAMPLE
To select the HALF tape margin setting:
1 While holding down ,
press once, and keep
held down.
2 While still holding down ,
continue pressing until HALF
is displayed.
3 Release .
F E E DAlt
Caps F U L L FrameUnderline
Length
Auto
Font 1 Font 2
Tape
F E E DAlt
Caps H A L F FrameUnderline
Length
Auto
Font 1 Font 2
Tape
63
HORIZONTAL ALIGNMENT FUNCTION
You can choose to align the text in one of three ways. In addition, if the Length functionwas used to set the length of the label, the text will align within the label according to theselected horizontal alignment setting.
Three settings exist, as follws. The default setting is LEFT.
To change the horizontal alignment setting:
1 While holding down , press once, and keep held down to dis-
play the current horizontal alignment setting.
2 While still holding down , continue pressing until the desired horizon-
tal alignment setting is displayed.
3 Release to apply the selected horizontal alignment setting to the entire text.
EXAMPLE
LEFT CENTER RIGHT
To select the RIGHT horizontal alignment setting:
1 While holding down ,
press once, and keep
held down.
2 While still holding down ,
continue pressing until
RIGHT is displayed.
3 Release .
Align
Align
L E F TH . A L I G N M E N TAlt
Caps FrameUnderline
Length
Auto
Font 1 Font 2
Align
R I G H TH . A L I G N M E N TAlt
Caps FrameUnderline
Length
Auto
Font 1 Font 2
Align
64
MIRROR PRINTING FUNCTION
With this function, you can print your text so that the characters can be read from thetape side of the tape. If mirror-printed labels are attached to glass or some other clearmaterial, they can be read correctly from the opposite side.
☞ When using the Mirror printing function, the text should be printed on clear tape.The default mirror printing setting is OFF.
To turn on or off the mirror printing setting:
1 While holding down , press once, and keep held down to
display the current mirror printing setting.
2 While still holding down , continue pressing until the desired mirror
printing setting is displayed.
3 Release to apply the selected mirror printing setting to the entire text.
EXAMPLE
ON
To select the ON mirror printing setting:
1 While holding down ,
press once, and keep
held down.
2 While still holding down ,
continue pressing until
ON is displayed.
3 Release .
Mirror
Mirror
O F FM I R R O RAlt
Caps FrameUnderline
Length
Auto
Font 1 Font 2
Mirror
O NM I R R O RAlt
Caps FrameUnderline
Length
Auto
Font 1 Font 2
Mirror
65
LENGTH FUNCTION
Although the length of the printed label automatically adjusts to fit the length of theentered text, there may be times when you will want to make a label with a specificlength. The Length function allows you to set the label length between 1.6” and 11.8”(4.0 cm and 30.0 cm).
The default length setting is OFF. When the Length function is set to ON, the Length indi-cator on the right side of the display lights up.
☞ Turning off the machine and turning it on again changes the length setting back toOFF.
To turn on or off the Length function:
1 While holding down , press once, and keep held down to dis-
play the current length of the label (the text and both margins) briefly, then displaythe current label length setting (ON or OFF).
2 While still holding down , continue pressing until the desired label
length setting is displayed.
☞ The Length indicator lights up when ON is selected.
3 Release . If ON was selected, the current label length setting is displayed.
4 Press or to select the desired length or use the number keys to enter thelength.
☞ To change the units (inches or centimeters) used to display the label length,
press until the desired units are displayed.
To change the length in 1” (1.0-cm)-steps, hold down either or ,and then release the key when the desired setting is displayed.
5 Press .
Length
Length
HomeEnd
HomeEnd
66
EXAMPLE
To select a label length of 5”:
1 While holding down , press once, and keep held
down.
2 While still holding down ,
continue pressing until ON is
displayed.
3 Release .
4 Press until 5.0 is displayed.
5 Press .
Length
2 . 1L E N G T H i n c h
O F FL E N G T H i n c hAlt
Caps FrameUnderline
Length
Auto
Font 1 Font 2
Alt
Caps FrameUnderline
Length
Auto
Font 1 Font 2
Alt
Caps FrameUnderline
Length
Auto
Font 1 Font 2
L E N G T H i n c h O N
Length
Alt
Caps FrameUnderline
Length
Auto
Font 1 Font 2
L E N G T H i n c h 3 . 9
Alt
Caps FrameUnderline
Length
Auto
Font 1 Font 2
L E N G T H i n c h 5 . 0
Home
67
PRINT KEY & FEED FUNCTION
After you have entered your text and chosen the desired format settings, you are ready toprint.
To print a label:
● Press once. The message “COPIES” followed by the number of the label
being printed is displayed.
☞ If NONE tape setting is selected and the tape is immediately, some printed
characters will be cut off. To feed the tape after printing, hold down
and once.
To feed the tape:● Hold down and press once. 1” (25 mm) of tape is fed out.
To cut the tape:● Push down on the tape cutter lever.
☞ In order to prevent damaging the tape, do not try to cut it while printing orfeeding. Pushing down on the tape cutter lever too far may break it.
EXAMPLE
To make a label using the NONE tape margin setting:
1 Press once.
2 Hold down and press once.
3 Push down on the tape cutter lever.
Mirror
Feed
Feed
1 / 1C O P I E SAlt
Caps FrameUnderline
Length
Auto
Font 1 Font 2
Mirror
Feed
68
NUMBERING FUNCTION
This function can be used to print many copies of the same text while increasing a certainnumber in the text by 1 after each label is printed.
To use the Numbering function:
1 Press , , or to position the cursor below the number that
you wish to increase.
2 Hold down and press . The message “NUMBER UNTIL 1–9?” appears
in the display.
3 Press the number key ( to ) of the last number that is to be printed.
☞ To cancel the Numbering, hold down and press (or press just
).
4 Press (or ) to begin printing the labels. The number of each copy is
displayed while it is being printed.
☞ After printing using the NONE tape magin setting, hold down and
press once to feed the tape before cutting it, otherwise some of the
printed characters may be cut off.
5 Press down on the tape cutter lever to cut the tape, and then use scissors to cutalong the printed dots to separate the labels.
EXAMPLE
To print three labels with numbers 1, 2 and 3:
1 Position the cursor below “1”.
HomeEnd
Number
Font M.Del
Number
Clear
Mirror
Feed
Alt
Caps FrameUnderline
Length
Auto
Font 1 Font 2
1: S T U D I O 1 _
69
2 Hold down and press
.
3 Press .
4 Press (or ).
5 Press in the tape cutter lever to cut the tape, then use scissors to cut alongthe cutting guide to separate the labels.
Alt
Caps FrameUnderline
Length
Auto
Font 1 Font 2
U N T I L 1 – 9 ?N U M B E R
Number
Alt
Caps FrameUnderline
Length
Auto
Font 1 Font 2
U N T I L 3N U M B E R
Width
Mirror
2 / 3C O P I E S
3 / 3C O P I E S
1 / 3C O P I E SAlt
Caps FrameUnderline
Length
Auto
Font 1 Font 2
Alt
Caps FrameUnderline
Length
Auto
Font 1 Font 2
Alt
Caps FrameUnderline
Length
Auto
Font 1 Font 2
✂ ✂✂
70
REPEAT PRINTING FUNCTION
This function allows you to print up to 9 copies of the same text.
To use the Repeat printing function:
1 Hold down and press . The message “COPIES UNTIL 1–9?” appears in
the display.
2 Press the number key ( to ) of the number of labels that you want.
☞ To cancel the Repeat printing, hold down and press (or press
just ).
3 Press (or ) to begin printing the labels. The number of each copy is
displayed while it is being printed.
☞ If NONE tape setting is selected and the tape is immediately, some printed
characters will be cut off. To feed the tape after printing, hold down
and once.
4 Press down on the tape cutter lever to cut the tape, and then use scissors to cutalong the printed dots to separate the labels.
EXAMPLE
To print three copies of a label:
1 Hold down and press
.
Repeat
Font M.Del
Repeat
Clear
Mirror
Feed
Alt
Caps FrameUnderline
Length
Auto
Font 1 Font 2
U N T I L 1 – 9 ?C O P I E S
Repeat
71
2 Press .
3 Press (or ).
4 Press down on the tape cutter lever to cut the tape, and then use scissors tocut along the cutting guide to separate the labels.
Alt
Caps FrameUnderline
Length
Auto
Font 1 Font 2
U N T I L 3C O P I E S
Width
Mirror
2 / 3C O P I E S
3 / 3C O P I E S
1 / 3C O P I E SAlt
Caps FrameUnderline
Length
Auto
Font 1 Font 2
Alt
Caps FrameUnderline
Length
Auto
Font 1 Font 2
Alt
Caps FrameUnderline
Length
Auto
Font 1 Font 2
✂ ✂
72
MEMORY FUNCTIONS
You can use the memory to store your most frequently used text files. The text remains inthe memory, even after all characters are removed from the display using the Clear func-
tion (holding down and pressing ).
When each file is stored, it is given a number to make recalling it easier. Up to 9 text filesor about 300 characters can be stored in the memory. Each stored text file can have amaximum of 99 characters.
Since a copy of the stored text file is recalled when the Recall function is used, the textcan be edited or printed without changing the originally stored file. When a file is nolonger needed or more space is necessary, the Memory delete function can be used todelete it.
☞ When inserting new batteries, be sure to insert the new ones within five minutes ofremoving the old ones, otherwise any text files stored in the memory will be lost(unless the machine is plugged into an electrical outlet with the AC adaptor).
STORING TEXTTo store a text file:
1 Hold down and press . The message “STORE SELECT 1–9?” appears
on the display.
☞ If 300 characters have already been stored, the error message “MEMORYFULL!” appears in the display. If this occurs, an existing text file must bedeleted before the new one can be stored.
2 Press the key ( to ) of the file number where you wish to store the text.
The text is stored under the selected file number and the text previously shown inthe display reappears.
☞ If a file is already stored under the selected file number, the message “OVER-WRITE?” appears in the display and you must decide whether or not to over-write it (delete it from the memory and store the new one).
To quit the Store function without storing the text, hold down and
press (or press just ).
Clear
Store
Font M.Del
Store Clear
73
To overwrite the stored file with the new one:
● Press to delete the previously stored file and store the new one under the
selected number.
☞ To go back and choose another file number without overwriting the text file,
press , and then press the key of a different file number.
RECALLING TEXTTo recall a text file:
1 Hold down and press . The message “RECALL SELECT 1–9?” appears
on the display.
2 Press the key ( to ) of the file number containing the text that you wish to
recall. The text stored under the selected file number is shown.
☞ To see other parts of the selected text file, press or .
To display the text stored under other file numbers, press or , orthe key of a different file number.
To quit the Recall function without recalling text, hold down and
press (or press just ).
3 Press . Any text previously entered in the display is erased and the text stored
under the selected file number is recalled into the display.
DELETING A FILETo delete a text file:
1 Hold down and press . The message “CLEAR SELECT 1–9?” appears on
the display.
Clear
Recall
Font M.Del
HomeEnd
Recall Clear
M.Del
74
2 Press the key ( to ) of the file number containing the text that you wish to
delete. The text stored under the selected file number is shown.
☞ To see other parts of the selected text file, press or .
To display the text stored under other file numbers, press or , orthe key of a different file number.To cancel the Memory delete function without deleting the text file, hold
down and press (or press just ).
3 Press to delete the text file that was selected.
EXAMPLE
To store text under file number 4:
1 Hold down and press
.
2 Press .
To recall the text from file number 4:
1 Hold down and press
.
Font M.Del
HomeEnd
M.Del Clear
Alt
Caps FrameUnderline
Length
Auto
Font 1 Font 2
S E L E C T 1 – 9 ?S T O R E
Store
Alt
Caps FrameUnderline
Length
Auto
Font 1 Font 2
4: J o h n S m i t h
Style
Alt
Caps FrameUnderline
Length
Auto
Font 1 Font 2
S E L E C T 1 – 9 ?R E C A L L
Recall
75
2 Press .
3 Press .
To delete the text stored under file number 4:
1 Hold down and press
.
2 Press .
3 Press .
Alt
Caps FrameUnderline
Length
Auto
Font 1 Font 2
[ 4 ] J o h n S m i tR E C A L L
Style
Alt
Caps FrameUnderline
Length
Auto
Font 1 Font 2
1: J o h n S m i t h _
Alt
Caps FrameUnderline
Length
Auto
Font 1 Font 2
S E L E C T 1 – 9 ?C L E A R
M.Del
Alt
Caps FrameUnderline
Length
Auto
Font 1 Font 2
[ 4 ] J o h n S m i tC L E A R
Style
Alt
Caps FrameUnderline
Length
Auto
Font 1 Font 2
1: J o h n S m i t h _
76
TROUBLESHOOTING
Problem Remedy
1. The display stays blank after youhave turned on the machine.
• Check that the AC adaptor is con-nected correctly.
• If you are using alkaline batteries,check that they are correctly inserted.
• If the batteries are low, replace themwith new ones.
2. The machine does not print or theprinted characters are blurred.
• Check that the tape cassette has beeninserted properly.
• If the tape cassette is empty, replace itwith a new one.
• Make sure that the tape compartmentcover has been closed.
3. The text files that you stored in thememory are no longer there.
• If the batteries are low, replace themwith new ones.
4. The printed characters are notformed properly.
• If you are using alkaline batteries,they may be low. Try using the ACadaptor or replace the batteries withnew ones.
5. A blank horizontal line appearsthrough the printed label.
• Clean the print head as explained onpage 9.
6. Striped tape appears. • You have reached the end of thetape. Replace the tape cassette with anew one.
7. The machine has “locked up” (i.e.,nothing happens when a key ispressed).
• Turn off the machine, and then while
holding down and ,
turn the machine back on. The textand formats in the display and all textfiles stored in the memory are erased.
Align
77
ERROR MESSAGE LIST
Error Message Cause Remedy
3 LINELIMIT!
• This message appears ifthree lines already exist
when you press .
• Limit the number of linesto three.
BATTERIESWEAK!
• This message appearswhen the installed alkalinebatteries become weak.
• Replace the batteries oruse the AC adaptor.
BUFFEREMPTY!
• This message appears if
you hold down
and press , but no
text has been entered inthe display.
• Enter some text beforestarting the function.
• This message appears ifyou try to print, but notext has been entered.
• Enter text before printing.
• This message appears ifyou try to store a text filein the memory, but notext has been entered inthe display.
• Enter text before storing.
BUFFERFULL!
• This message appears ifyou try to enter a charac-ter, symbol, bar code,return or space after 99characters have alreadybeen entered.
• Delete some existing textso that more text can beentered.
Length
78
CAN’THERE!
• This message appears ifthe cursor is at the end ofthe text when you hold
down and press
.
• Move the cursor below anumber before holding
down and press-
ing .
CHANGEADAPTOR
• This message appears if ahigh-voltage adaptor isbeing used.
• Remove the high-voltageadaptor and connect theadaptor designed exclu-sively for this machine.
CUTTERERROR!
• This message appears ifthe tape cutter lever ispressed down while alabel is being printed.
• Release the tape cutterlever.
INVAL.CHRS!
• This message appears ifthe cursor is not below anumber when you hold
down and press
.
• Move the cursor below anumber before holding
down and press
.
LENGTHLIMIT!
• This message appears if thetext is longer than 1 meterwhen you try to print.
• Shorten the text to lessthan 1 meter before tryingto print.
• This message appears ifthe Length function isused to set a label lengththat is less than 1.6” (4.0cm) or more than 11.8”(30.0 cm).
• Set the label length between 1.6” (4.0 cm) and 11.8” (30.0 cm).
• This message appears ifthe Tab Length function isused to set a tab lengththat is more than 11.8”(30.0 cm).
• Set the tab length so thatit is less than 11.8” (30.0cm).
Error Message Cause Remedy
Number
Number
Number
Number
79
LINELIMIT!
• This message appears ifthe number of lines in thetext is greater than themaximum number oflines possible for theinstalled tape.
• Reduce the number oflines or install a tape ofgreater width.
MEMORYFULL!
• This message appears ifyou try to store a text fileafter 300 characters havealready been stored in thememory.
• Delete an unwanted fileto make room for the newone.
NOFILES!
• This message appears ifyou try to recall or deletea text file from the mem-ory when none are stored.
• Store a text file first.
NUMBERTOO SMALL!
• This message appears ifthe number that is set tobe printed using theNumbering function isless than the numberabove the cursor.
• Press the key of a numberthat is greater than thenumber in the text.
ROMPROBLEM!
• This message appears ifthere is a problem withthe machine’s read onlymemory.
• Contact your service rep-resentative.
REPLACE BATTERIES!
• This message appears ifthe installed alkaline bat-teries are about to runout.
• Replace the batteries oruse the AC adaptor.
SYSTEMERROR!
• This message appears ifthere is a problem withthe machine’s software.
• Contact your service rep-resentative.
Error Message Cause Remedy
80
NOTAPE!
• This message appears ifyou try to print a label orfeed the tape when no tapecassette is installed.
• Install a tape cassette andtry again.
TABLIMIT!
• This message appears if50 tabs have already beenadded to the text when
you press .
• Limit the number of tabsin the text to 50.
TEXTTOO HIGH!
• This message appears ifthe size of the text islarger than the width ofthe installed tape.
• Reduce the size of thecharacters or install awider tape.
TEXTTOO LONG!
• This message appears ifthe length of the text islonger than the labellength that has been setusing the Length func-tion.
• Delete some of the text,reduce the characterwidth or increase the setlabel length.
Error Message Cause Remedy
Tab
81
SPECIFICATIONS
HARDWARE
SOFTWARE
Input Device: Keyboard - 51 keys
LCD: 7 × 5 dots12 characters × 2 lines17 indicators
Print Tape: Pressure-sensitive, Adhesive-based26’ 3” (8 m) longFour widths available:
1/4” (6 mm)3/8” (9 mm)1/2” (12 mm)3/4” (18 mm)
Power Supply: Six AA alkaline batteries (AM3, LR6) or optional AC adaptor Auto power-off if no key is pressed for 5 minutes
Print Head: 128 dot / 180 dpi
Dimensions: 7” (W) × 8 1/16” (D) × 2 23/63” (H)(178 × 205 × 60 mm)
Weight: 1.5 lbs (700 g) (without a tape cassette and batteries installed)
Buffer Size: Maximum 99 charactersMaximum three lines
Memory Size: 300 characters
Character Size: Six sizes (6, 9, 12, 18, 24 and 36 points) + 48 point (Capital letters only)All are available in normal and wide
Print Styles: Normal, Outline, Bold, Shadow(each can be combined with Italic), and Vertical
82
ACCESSORIES
●
Supplies
Obtain tape cassettes from your nearest authorized dealer. Use only Brother TZ tapes with this machine. Brother cannot be held responsible fortrouble caused by the use of unauthorized supplies. Do not use tapes that do nothave the mark.
Stock No. DescriptionQTY/
PACKAGEPRICE
3/4” (18mm)-wide laminated tapes
TZ-141 Black characters on clear tape 1 $20.99TZ-145 White characters on clear tape 1 $20.99TZ-241 Black characters on white tape 1 $20.99TZ-242 Red characters on white tape 1 $20.99TZ-243 Blue characters on white tape 1 $20.99TZ-344 Gold characters on black tape 1 $24.99TZ-345 White characters on black tape 1 $23.99TZ-441 Black characters on red tape 1 $20.99TZ-541 Black characters on blue tape 1 $20.99TZ-545 White characters on blue tape 1 $23.99TZ-641 Black characters on yellow tape 1 $20.99TZ-741 Black characters on green tape 1 $20.99TZ-B41 Black characters on fluorescent orange tape 1 $24.99TZ-M41 Black characters on clear (matte) tape 1 $20.99
TZ-WB41 Black characters on Bugs Bunny tape 1 $23.99TZ-WT41 Black characters on Taz tape 1 $23.99TZ-WS41 Black characters on Tweety & Sylvester tape 1 $23.99
1/2” (12mm)-wide laminated tapes
TZ-131 Black characters on clear tape 1 $16.99TZ-231 Black characters on white tape 1 $17.99TZ-232 Red characters on white tape 1 $17.99TZ-335 White characters on black tape 1 $20.99
3/8” (9mm)-wide laminated tapes
TZ-121 Black characters on clear tape 1 $14.99TZ-221 Black characters on white tape 1 $16.99TZ-325 White characters on black tape 1 $18.99TZ-421 Black characters on red tape 1 $16.99
83
Special tapes
Stamp kit
Options
1/4” (6mm)-wide laminated tapes
TZ-111 Black characters on clear tape 1 $12.99TZ-211 Black characters on white tape 1 $14.99TZ-315 White characters on black tape 1 $17.99
Stock No. DescriptionQTY/
PACKAGEPRICE
TZ-SE4 Black characters on 3/4” (18 mm) security tape 1 $29.99TZ-FA3 Blue characters on 1/2” (12 mm) fabric tape 1 $24.99
Stock No. DescriptionQTY/
PACKAGEPRICE
SK-MBStamp-making kit for Medium stamp with blackink
1 $37.99
SH-MBAdditional stamper for Medium stamp withblack ink
1 $24.99
Stock No. DescriptionQTY/
PACKAGEPRICE
AD-60 AC Adapter 1 $24.99
Stock No. DescriptionQTY/
PACKAGEPRICE
P-TOUCH ACCESSORY ORDER FORM
Dear Customer:This order form is provided for your convenience should your retailer not stock theitem(s) needed. To order by mail, send this completed form along with proper payment tothe address below OR credit card holders: Call toll-free 1-888-879-3232, fax completedorder form to 1-800-947-1445, or visit our web site at http://www.brothermall.com.Please refer to the Accessories listing in your User's Guide for stock no. and price.
* Prices subject to change without notice.
Stock No. Description Price Quantity Total
Subtotal
Name:
Accessory Subtotal:
$
Address: AZ, CA, CO, CT, FL, GA, IL, LA, MA,MD, MI, MN, MO, NC, NJ, NV, NY,OH, PA, TN, TX, VA, WAresidentsadd applicable sales tax
City:
State/Zip: $
Daytime Phone:
Shipping/Handing Options
SEND ORDER FORM TO:
Please choose one:
Brother International Corp.Attn: Consumer Accessory Div.P.O. Box 341332Bartlett, TN38184-1332
• Standard ($5.00)
• 2nd day air freight ($8.75) Mandatory for alldeliveries outside of the continental U.S.(Alaska, Hawaii, Puerto Rico, Virgin Islands& Canada)
• All other overseas orders ($25.00) $
TOTAL DUE (US dollars)
$
Method of payment (Check one)
( ) Visa ( ) MasterCard ( ) Discover ( ) American Express ( ) Check/Money Order
Account Number
Expiration Date
Signature
✂
P-TOUCH ACCESSORY ORDER FORM
Dear Customer:This order form is provided for your convenience should your retailer not stock theitem(s) needed. To order by mail, send this completed form along with proper payment tothe address below OR credit card holders: Call toll-free 1-888-879-3232, fax completedorder form to 1-800-947-1445, or visit our web site at http://www.brothermall.com.Please refer to the Accessories listing in your User's Guide for stock no. and price.
* Prices subject to change without notice.
Stock No. Description Price Quantity Total
Subtotal
Name:
Accessory Subtotal:
$
Address: AZ, CA, CO, CT, FL, GA, IL, LA, MA,MD, MI, MN, MO, NC, NJ, NV, NY,OH, PA, TN, TX, VA, WAresidentsadd applicable sales tax
City:
State/Zip: $
Daytime Phone:
Shipping/Handing Options
SEND ORDER FORM TO:
Please choose one:
Brother International Corp.Attn: Consumer Accessory Div.P.O. Box 341332Bartlett, TN38184-1332
• Standard ($5.00)
• 2nd day air freight ($8.75) Mandatory for alldeliveries outside of the continental U.S.(Alaska, Hawaii, Puerto Rico, Virgin Islands& Canada)
• All other overseas orders ($25.00) $
TOTAL DUE (US dollars)
$
Method of payment (Check one)
( ) Visa ( ) MasterCard ( ) Discover ( ) American Express ( ) Check/Money Order
Account Number
Expiration Date
Signature
✂
INTRODUCCIÓN
Gracias por adquirir una P-Touch 1800.
Su nueva P-Touch le permitirá diseñar y crear etiquetas y membretes para cualquier tipode aplicación. Su versatilidad le permitirá crear etiquetas personales seleccionando dis-tintos diseños de marcos y muchos tamaños y estilos de caracteres. Además, los cuatrodiferentes anchos de cinta (1/4
″
(6 mm), 3/8
″
(9 mm), 1/2
″
(12 mm), 3/4
″
(18 mm) y1
″
(24 mm)) y la variedad de los colores de la cintas le hará posible imprimir etiquetaspersonales, útiles para relleno con código de colores. Con la función de membretes,podrá hacer membretes con facilidad y rapidez para soportes de membretes entintadosreutilizables.
Ya no hay por qué preocuparse por tareas urgentes que requieren impresión profesional.En la oficina, la fábrica, el laboratorio, o en casa, la calidad y el rendimiento de la P-Touch 330/350 la convierten en una máquina muy práctica.
Para terminar, puesto que esta guía del usuario le será de gran utilidad, le aconsejamosque la guarde en un lugar accesible para poder consultar en cualquier momento.
(Los modelos PT-1800 y PT-1810 disponen de las mismas funciones. Sin embargo, sola-mente el modelo PT-1810 dispone de estuche de transporte.)
AVISO DE LA FCC
Este equipo ha sido probado y cumple con los límites de un aparato digital de la ClaseB, siguiendo el apartado 15 de las normas de la FCC. Estos límites están pensados paraproporcionar una protección razonable contra interferencias nocivas dentro de unainstalación residencial. Este equipo podría interferir de forma nociva con comunica-ciones por radio si no se instala y utiliza siguiendo las instrucciones. No obstante, noexiste ninguna garantía de que no vayan a suceder interferencias en una instalaciónconcreta. Si este equipo causara interferencias nocivas con la recepción de radio otelevisión, lo cual puede determinarse poniendo el equipo en ON u OFF, se recomien-da que el usuario intente corregir dichas interferencias mediante una de las siguientesmedidas:
- Reoriente o ponga la antena receptora en otro lugar.- Aumente la separación entre el equipo y el receptor.- Conecte el equipo en una toma de un circuito diferente de la que esté conectadael receptor.
- Consulte a su distribuidor o a un técnico experimentado de radio/televisión.
A continuación se indican los números de patente y de publicación de patente rela-cionados con este producto:
USP4839742 USP4983058 USP5120147USP4927278 USP5009530USP4976558 USP5069557
i
ÍNDICE
PRECAUCIONES GENERALES ............................................................................. 1
PILAS ................................................................................................................... 2
ADAPTADOR DE CA OPCIONAL ....................................................................... 3
CASETES DE CINTA............................................................................................. 4
CABEZAL DE IMPRESIÓN Y RODILLOS.............................................................. 5
COLOCACIÓN DE ETIQUETAS........................................................................... 6
TECLA DEL CURSOR........................................................................................... 7
TECLAS CODE, ALT Y SHIFT ............................................................................... 9
TECLA DE RETORNO........................................................................................ 10
TABULACIÓN ................................................................................................... 11
TECLA DE BORRADO (DEL).............................................................................. 13
FUNCIÓN DE BORRADO DE LÍNEA (LINE OUT) ............................................. 14
FUNCIÓN DE REPOSICIÓN (CLEAR) ................................................................ 14
FUNCIÓN DE ACENTOS................................................................................... 15
FUNCIÓN DE SÍMBOLOS................................................................................. 16
FUNCIÓN DE FORMATO AUTOMÁTICO........................................................ 17
FUNCIÓN DE MEMBRETE................................................................................. 19
FUNCIONES DE TAMAÑO Y DE ANCHURA.................................................... 20
FUNCIÓN DE ESTILO ....................................................................................... 21
FUNCIÓN DE SUBRAYADO............................................................................. 22
FUNCIÓN DEL TIPO DE CARACTERES ............................................................. 23
FUNCIÓN DE MARCOS.................................................................................... 24
FUNCIÓN DE CINTA ........................................................................................ 25
FUNCIÓN DE LA ALINEACIÓN HORIZONTAL................................................ 26
FUNCIÓN DE IMPRESIÓN DE ESPEJO.............................................................. 27
LENGTH FUNCTIÓN ........................................................................................ 28
FUNCIÓN DE LA TECLA DE IMPRESIÓN Y AVANCE ....................................... 29
FUNCIÓN DE NUMERACIÓN .......................................................................... 30
FUNCIÓN DE IMPRESIÓN REPETIDA............................................................... 31
FUNCIONES DE LA MEMORIA ......................................................................... 32
SOLUCIÓN DE PROBLEMAS ............................................................................ 35
LISTA DE MENSAJES DE ERROR........................................................................ 36
ESPECIFICACIONES........................................................................................... 40
ACCESORIOS .................................................................................................... 41
1
PRECAUCIONES GENERALES
• Con esta máquina emplee sólo cintas TZ Brother. No emplee cintas que no tengan lamarca .
• No tire de la cinta que se alimenta desde la P-Touch. Podría dañar el casete de cinta.
• No utilice la máquina en lugares polvorientos, y manténgala alejada de la luz solardirecta y la lluvvia.
• No exponga la máquina a altas temperaturas ni humedad. No la deje nunca en eltablero de instrumentos ni en la parte trasera de su automóvil.
• No deje nada que sea de goma o vinilo encima de la máquina durante períodos pro-longados. Podría producir manchas.
• No limpie la máquina con alcohol ni con otros solventes orgánicos. Emplee sola-mente un paño suave y seco.
• No ponga ningún objeto encima ni dentro de la máquina.
• Para evitar daños, no toque el borde de la cuchilla.
• Cuando inserte pilas nuevas, asegúrese de hacerlo antes de que transcurran cincominutos desde el momento en que extrae las pilas gastadas, porque de lo contrario seperderían todos los archivos de texto (a menos que la máquina esté enchufada a unatoma de CA con el adaptador de CA).
• Emplee sólo el adaptador de CA (modelo AD-60) exclusivamente diseñado para estamáquina. El empleo de otro cancelaría la garantía.
• No intente desmontar el adaptador de CA.
• Cuando la máquina no se utilice durante períodos prolongados de tiempo y no seanecesario conservar los archivos de texto en la memoria, desenchufe el adaptador deCA, y saque las pilas para evitar fugas de las mismas que podrían ser causa de dañosen la máquina.
• Cuando el adaptador de CA esté enchufado en la máquina, si se desenchufa el adap-tador de la toma de CA se correrá el riesgo de perder todos los archivos de texto de lamemoria, aunque las pilas estén insertadas.
• En esta máquina, emplee seis pilas alcalinas del tamaño AA.
2
PILAS
Esta máquina ligera y portátil puede utilizarse en cualquier lugar instalando seis (6)
pilasalcalinas AA
. Cuando cambie las pilas, reemplace siempre las seis pilas al mismo tiempo.
Para cambiar las pilas:
1
Extraiga la cubierta del compartimiento de las pilas de la parte posterior de lamáquina.
2
Si ya hay pilas instaladas, extráigalas.
3
Inserte seis pilas alcalinas AA nuevas, asegurándose de que quedan orientadas en ladirección correcta.
4
Coloque la cubierta del compartimiento de las pilas.
☞
Asegúrese de insertar las pilas nuevas antes de que transcurran cinco minu-tos desde que se extraen las pilas gastadas, porque de lo contrario el textoque se visualiza en la pantalla y los archivos de texto almacenados en lamemoria se perderían (a menos que la máquina esté enchufada a una tomade CA con el adaptador de CA).
Extraiga las pilas y desconecte el adaptador de CA si no se propone utilizar lamáquina durante períodos de tiempo prolongados. Cuando se desconecta laalimentación, se pierden el texto que se muestra en la pantalla y el que estáalmacenado en la memoria.
Si no se emplean pilas alcalinas, no podrán imprimirse tipos de caracteresgrandes.
3
ADAPTADOR DE CA OPCIONAL
El adaptador de CA (modelo AD-60) le permite emplear esta máquina siempre que dis-ponga de una toma de corriente eléctrica.
Para conectar el adaptador de CA opcional:
1
Inserte la clavija del adaptador en el conector que tiene la marca DC IN 9.5V allado derecho de la máquina.
2
Inserte la clavija del adaptador de CA en la toma de corriente más cercana.
☞
Emplee sólo el adaptador de CA diseñado exclusivamente para estamáquina.
Extraiga las pilas y desconecte el adaptador de CA si no se propone utilizar lamáquina durante períodos de tiempo prolongados. Cuando se desconecta laalimentación, se pierden el texto que se muestra en la pantalla y el que estáalmacenado en la memoria.
Cuando el adaptador de CA esté enchufado en la máquina, si se desenchufael adaptador de la toma de CA se correrá el riesgo de perder todos los archi-vos de texto de la memoria, aunque las pilas estén insertadas.
Se recomienda emplear el adaptador de CA para imprimir tipos de caracteresgrandes y códigos de barras con cintas de 18 mm (3/4”) porque esta opera-ciónes pueden gastar las pilas con rapidez.
4
CASETES DE CINTA
Un casete de TZ se suministra con la unidad. Sin embargo, para esta máquina hay dispo-nibles una amplia gama de casetes de cinta TZ de distintos colores y tamaños, es posiblecrear etiquetas diferentes codificadas por colores o tamaños.
Para cambiar el casete de cinta:
1
Levante la cubierta del compartimiento de la cinta para abrirla. Se libera tambiénentonces el casete instalado.
2
Si ya hay un casete instalado, extráigalo tirando del mismo recto hacia arriba.
3
Si la cinta entintadora del otro casete se afloja, utilice un dedo para bobinar la ruedadentada en el sentido de la flecha de dicho casete hasta tensar la cinta. Además,cerciórese de que el extremo de la cinta esté debajo de las guías de la misma.
☞
Si está utilizando un casete de cinta nuevo provisto de retén, cerciórese deextraer éste.
4
Inserte firmemente el casete de cinta en el compartimiento de la cinta asegurándosede que toda la parte posterior del casete está en contacto con la inferior del compar-timiento.
☞
Cuando inserte el casete de cinta, asegúrese de que la cinta interior no estéenganchada en la esquina de la guía metálica.
5
Cierre la cubierta del compartimiento y conecte la alimentación de la máquina siestaba desconectada.
6
Mantenga pulsada y presione una vez para que la cinta avance y
así quede con la tensión óptima.
7
Presione la palanca de la cuchilla de la cinta para cortar la cinta sobrante.
Feed
5
CABEZAL DE IMPRESIÓN Y RODILLOS
De vez en cuando, motas de polvo o suciedad se adhieren al cabezal de impresión y alos rodillos de la máquina. Suele suceder cuando se emplea la unidad en exteriores o enlugares con mucho polvo. Si alguna parte del cabezal de impresión está cubierta depolvo, es posible que aparezca una franja horizontal blanca por el texto de la etiqueta.
Por lo tanto, al igual que con las grabadoras de cintas, el cabezal de la máquina deberálimpiarse de vez en cuando.
Para limpiar el cabezal de impresión y los rodillos:
1
Desconecte la alimentación de la máquina.
2
Abra la cubierta del compartimiento de la cinta, extraiga el casete, si está dentro. Elcabezal de impresión y los rodillos están situados dentro del compartimiento de lacinta.
3
Cabezal de impresión: Emplee un palillo con punta de algodón seco para frotar concuidado el cabezal de impresión con movimiento hacia arriba y abajo.Rodillos: Emplee un palillo con punta de algodón seco para frotar cada rodillo conmovimiento hacia arriba y abajo mientras los gira con el dedo.
4
Pruebe de nuevo la impresión.
Si todavía queda polvo:
5
Repita el paso
3
empleando un palillo con cabeza de algodón humedecido enalcohol isopropílico (limpieza).
Si no funciona nada de lo de arriba, póngase en contacto con el representante de servi-cio.
Cabezal de impresión
Cabezal de impresión
Rodillos Palillo de cabeza de algodón
6
COLOCACIÓN DE ETIQUETAS
CINTA LAMINADA
La varilla suministrada permite que, en las cintas laminadas, usted pueda extraer facil-mente el papel del dorso de la etiqueta.
1
Tome la cinta con la mano izquierda, con la superficie impresa arriba, y tome lavarilla con la mano derecha.
2 Pase la mitad de la cinta por el orificio estrecho largo de la varilla.
3 Gire tres cuartos de vuelta la varilla hacia usted y separe la varilla de usted como semuestra abajo.
4 Pele el papel del dorso de la etiqueta.
CINTAS DE TELA
La cinta de tela se emplea para adherir un trozo de tela impresa con el texto en prendarde vestir empleando una plancha. Después de imprimir el texto en la cinta de tela y dehaber cortado la etiqueta empleando unas tijeras, coloque la etiqueta sobre una prendaplanchada en la posición el la que desee ponerla de modo que el texto impreso puedaleerse correctamente. Cubra la etiqueta con otra tela y emplee un ajuste de la plancha detemperatura medio-alta (320 a 356˚F (160 a 180 ˚C)) para presionar con firmeza durante10 a 15 segundos. Para más detalles, consulte las instrucciones suministradas con elcasete de cinta de tela.
CINTAS DE MEMBRETES
Consulte las páginas 19 para encontrar la explicación detallada sobre el empleo de cintasde membretes para hacer membretes.
GH
ABCDEF
ABCDEF
7
TECLA DEL CURSOR
El visualizador de LCD de esta máquina muestra dos filas de 11 caracteres; sin embargo,el texto que usted cree puede tener hasta 99 caracteres de longitud. Podrá revisar y editarel texto empleando las teclas del cursor para moverlo y que muestre las distintas partesen el visualizador.
TECLA DEL CURSOR IZQUIERDA Para mover el cursor un carácter hacia la izquierda:
● Presione una vez.
Para mover el cursor varios caracteres hacia la izquierda:
● Mantenga presionado hasta que el cursor se mueva a la posición deseada.
Para mover el cursor al principio de la línea actual:
● Mantenga presionado y presione .
TECLA DEL CURSOR DERECHAPara mover el cursor un carácter hacia la derecha:
● Presione una vez.
Para mover el cursor varios caracteres hacia la derecha:
● Mantenga presionado hasta que el cursor se mueva a la posición deseada.
Para mover el cursor al final de la línea actual:
● Mantenga presionado y presione .
TECLA DEL CURSOR HACIA ARRIBAPara mover el cursor a la línea anterior:
● Presione una vez.
☞ Si el cursor está en la primera línea del texto, se moverá al principio de lalínea.
Para mover el cursor varias líneas hacia arriba:
● Mantenga presionado hasta que el cursor se mueva a la posición deseada.
Para mover el cursor al principio de todo el texto:
● Mantenga presionado y presione .
Home
Home
Home
8
TECLA DEL CURSOR HACIA ABAJOPara mover el cursor a la línea siguiente:
● Presione una vez.
☞ Si el cursor está en la última línea del texto, se moverá al final de la línea.Para mover el cursor varias líneas hacia abajo:
● Mantenga presionado hasta que el cursor se mueva a la posición deseada.
Para mover el cursor al final de todo el texto:
● Mantenga presionado y presione .
End
End
End
9
TECLAS CODE, ALT Y SHIFT
La mayoría de los caracteres pueden introducirse simplemente presionando sus teclas.Sin embargo, para emplear funciones especiales o para introducir letras en mayúsculas,caracteres acentuados y algunos símbolos, se requieren las siguientes teclas especiales.
TECLA CODEPara emplear una función impresa encima de la tecla:
● Mantenga presionado y presione la tecla que está inmediatamente debajo de la función deseada.
TECLA ALTPara escribir los caracteres impresos en color del lado derecho de las teclas:
● Mantenga presionado y presione la tecla del carácter deseado escrita en color.
El indicador Alt, de la izquierda del visualizador, se encenderá mientras se tiene
presionado .
TECLA SHIFTPara escribir una letra mayúscula o un símbolo impreso en la esquina superior izquierdade la tecla:
● Mantenga presionado y presione la tecla de la letra o símbolo deseado.
El modo Caps (mayúsculas) es similar a mantener presionada . Le permite escribir
letras mayúsculas continuamente.
Para escribir muchas letras mayúsculas:
1 Mantenga presionado y presione . El indicador de Caps, de laizquierda del visualizador, se encenderá.
2 Presione las teclas de las letras o símbolos deseados.
3 Para salir del modo Caps, mantenga presionado y presione . Se apa-gará el indicador de Caps.
Symbol
Symbol
Caps
Caps
Caps
Caps
10
TECLA DE RETORNO
Al igual que en una máquina de escribir o procesador de texto, la tecla de retorno
( ) de esta máquina se emplea para poner fin a una línea de texto y empezar otra.
Cuando haya terminado de introducir una línea, presione la tecla de retorno para haceruna línea nueva y mover al cursor a la misma.
☞ Un bloque sólo puede contener un máximo de tres líneas de texto. Si presiona
cuando el cursor está situado en la tercero línea, aparecerá el mensaje de
error “3 LINE LIMIT!”.
La tecla de retorno también podrá utilizarse para seleccionar un ítem de una lista (p. ej.,añadir un símbolo o un carácter acentuado al texto) o para aplicar un ajuste seleccio-nado.
Es posible que aparezcan en el visualizador de LCD algunas preguntas para que confirmeun comando, especialmente cuando la función que usted ha seleccionado es para borrar
o afectar archivos. En estos casos, si presiona es como si respondiera “sí”.
☞ Para contestar “no”, presione . Consulte la descripción de la TECLA DE
BORRADO (DEL) de la página 13.
Anchuras de cintaNúmero máximo de líneas que pueden
imprimirse
1/4” (6 mm) 1
3/8” (9 mm) 2
1/2” (12 mm) 3
3/4” (18 mm) 3
Clear
11
TABULACIÓN
Esta función le permitirá separar secciones de una línea de texto añadiendo tabulaciones.Esto le permitirá crear columnas perfectamente alineadas sin tener que introducir variosespacios. Todas las tabulaciones tendrán la misma longitud y se medirán desde elcomienzo de la línea, o de la tabulación anterior, si es que existe. La longitud de lastabulaciones podrá ajustarse entre 0,0” y 11,8” (0,0 y 30,0 cm).
☞ El texto no podrá contener más de 50 tabulaciones. Si ya ha añadido 50 tabula-
ciones al texto, cuando presione , aparecerá el mensaje de error “TAB
LIMIT”.
Para ajustar la longitud de las tabulaciones:
1 Mantenga pulsada y presione una vez. Se visualizará la longitud de
tabulación actual.
2 Presione o hasta que se visualice la longitud deseada, o utilice las
teclas numéricas para introducir la longitud.
☞ Para cambiar las unidades (pulgadas o centímetros) utilizadas para la indicación
de la longitud de las tabulaciones, presione hasta que se visualicen las uni-
dades deseadas.
3 Presione .
Para añadir una tabulación:
● Mantenga pulsada y presione una vez . La marca de tabulación ( )
aparecerá en el texto para indicar la posición de la tabulación.
☞ Si el texto delante de una tabulación sobrepasa el punto en el que tiene quecomenzar la sección siguiente de texto, tal texto comenzará en la siguienteposición de tabulación.Por ejemplo, si la longitud está ajustada a 2” y escribe el texto siguiente:
Tab
Tab Length
HomeEnd
Tab
2: J K L M N O P Q R S T U1: A B C D E F G H I
12
Se imprimirá la etiqueta mostrada a continuación.
J K L M N O P Q R S T UA B C D E F G H I
Margen Tabulación (2 inch) Tabulación (2 inch) Margen
13
TECLA DE BORRADO (DEL)
La tecla de borrado ( ) le permite eliminar caracteres situados a la izquierda de la
posición actual del cursor. Se diferencia de la tecla del cursor izquierda ( ) quesólo mueve el cursor sin borrar ningún carácter.
La tecla de borrado también puede utilizarse para abandonar la mayor parte de funcionesy volver a la visualización anterior sin cambiar el texto.
Es posible que aparezcan en el visualizador de LCD algunas preguntas para que confirmeun comando, especialmente cuando la función que usted ha seleccionado es para borrar
o afectar archivos. En estos casos, si presiona es como si respondiera “sí”.
☞ Para contestar “no”, presione . Consulte la descripción de la TECLA DE
RETORNO de la página 10.Para borrar un carácter:
1 Presione , , , o para situar el cursor debajo del carácter queestá inmediatamente a la derecha del carácter que usted desea borrar.
2 Presione una vez.
Para borrar una secuencia de caracteres:
1 Presione , , , o para situar el cursor debajo del carácter queestá inmediatamente a la derecha del último carácter que usted desea borrar.
2 Mantenga presionado hasta que se hayan borrado todos los caracteres que
usted deseaba borrar.
Clear
Clear
HomeEnd
Clear
HomeEnd
Clear
14
FUNCIÓN DE BORRADO DE LÍNEA (LINE OUT)
Con la función de borrado de línea, podrá sacar con facilidad una línea entera de texto.
Para borrar una línea de texto:
1 Presione , , , o para situar el cursor dentro de la línea deltexto que usted desee borrar.
2 Mantenga presionado y presione una vez.
☞ Cada vez que se presione mientras se tiene presionado , se
borrará una línea de texto.
FUNCIÓN DE REPOSICIÓN (CLEAR)
Si borra la visualización antes de introducir nuevo texto, la función Reposición podrá uti-lizarse para elegir si se desea borrar todo el texto, y todas las funciones de formato (Tipode caracteres, Tamaño, Ancho, Estilo, Subrayado, Marco, Margen de la cinta, Alinea-ción, Longitud de la tabulación, Impresión de espejo y Longitud) volverán a sus ajustesiniciales, o borrar solamente texto.
Para borrar todo el texto y reponer todos los formatos a sus ajustes iniciales:
1 Mantenga presionado y presione .
2 Presione o hasta que se seleccione TEXT&FORMAT (parpadeando).
☞ Para volver al texto sin borrar nada, presione .
3 Presione .
HomeEnd
Line Out
Line Out
Clear
HomeEnd
Clear
15
FUNCIÓN DE ACENTOS
La función de acentos también podrá utilizarse para añadir caracteres acentuados al
texto. Muchos de estos caracteres podrán introducirse empleando .
Los caracteres acentuados se agrupan de acuerdo con la letra mayúscula o minúsculacon la que se combinan. Hay disponibles los siguientes caracteres acentuados:
Para escribir un carácter acentuado:
1 Mantenga presionado y presione . Aparecerá el mensaje “a-u/A-U?”en el visualizador.
2 Presione la tecla de la letra acentuada deseada.
☞ Para escribir una letra mayúscula, mantenga pulsada (o mantenga pul-
sada y presione para pasar al modo de mayúsculas) antes de
pulsar la tecla de la letra.
3 Presione o hasta que parpadee el carácter acentuado.
4 Presione . La letra y el acento parpadearán alternadamente en el texto.
☞ Para escribir una secuencia de caracteres acentuados, mantenga presionada
antes de pulsar . Después continúe añadiendo caracteres
acentuados seleccionándolos como se ha explicado en los pasos 2 y 3,
manteniendo pulsada y presionando . Después de haber
seleccionado el último carácter de la serie, presione simplemente .
LetrasCaracteres acentuados
LetrasCaracteres acentuados
a à á ä â ã å æ I Í Ï Î
A À Á Ä Â Ã Å Æ n ñ
c ç N Ñ
C Ç o ó ö ô õ
e è é ë ê e O Ó Ö Ô Õ
E È É Ë Ê E u ù ú ü û
i í ï î U Ù Ú Ü Û
Symbol
˜
Accent
Caps
Caps
16
FUNCIÓN DE SÍMBOLOS
Además de letras, de los símbolos y los números de las teclas, hay 126 marcas adiciona-les con la función de símbolos.
Los siguientes símbolos están disponibles:
Para escribir un símbolo:
1 Mantenga presionado y presione . Aparecerá una fila símbolos en elvisualizador.
2 Presione o para visualizar distintas filas de símbolos y presione
o hasta que parpadee el símbolo deseado.
3 Presione . El símbolo aparecerá en el texto.
☞ Para escribir una secuencia de símbolos, mantenga presionada antes
de pulsar . Después continúe añadiendo símbolos seleccionándolos
como se ha explicado en los pasos 2 y 3, manteniendo pulsada y
presionando . Después de haber seleccionado el último símbolo de
la serie, presione simplemente .
Symbol
HomeEnd
17
FUNCIÓN DE FORMATO AUTOMÁTICO
Con la función de formato automático, podrá seleccionar gran variedad de formatos pre-ajustados adecuados para su necesidad específica. Esta función ajustará automática-mente la longitud de la etiqueta y los márgenes de la cinta sin cambiar el texto ni ningúnotro formato, permitiéndole crear etiquetas con mayor rapidez y facilidad.
Los formatos preajustados son los siguientes:
Ajuste de formato automático
Ajuste de longi-tud de la eti-
queta
Aajuste del margen de la
cinta
Aajuste de la ali-neación horizontal
DEFAULT OFF FULL LEFT
3.5"FLOPPY 2.8” (7.0 cm) NARROW CENTER
5"FLOPPY 4.8” (12.2 cm) NARROW CENTER
VHS SPINE 5.5” (14.0 cm) NARROW CENTER
VHS 3.0” (7.7 cm) NARROW CENTER
VCR8mm CASE 3.6” (9.2 cm) NARROW CENTER
VCR8mm 2.9” (7.3 cm) NARROW CENTER
VHS-C SPINE 1.8” (4.5 cm) NARROW CENTER
VHS-C 2.3” (5.8 cm) NARROW CENTER
AUDIO 3.5” (8.9 cm) NARROW CENTER
DAT CASSETTE 2.2” (5.6 cm) NARROW CENTER
MINI DISK 2.0” (5.2 cm) NARROW CENTER
ORGANIZER L 3.2” (8.2 cm) NARROW CENTER
ORGANIZER S 2.6” (6.5 cm) NARROW CENTER
FILE LONG 7.2” (18.3 cm) NARROW CENTER
FILE SHORT 3.7” (9.4 cm) NARROW CENTER
18
Para seleccionar un formato preajustado:
1 Mantenga pulsada y presione una vez . El ajuste actualmente selec-
cionado parecerá en el visualizador.
2 Pulse o para seleccionar el ajuste deseado.
☞ El ajuste predeterminado (DEFAULT) podrá seleccionarse presionando
.
3 Presione para aplicar el ajuste seleccionado.
☞ El indicador de longitud se encenderá cuando seleccione un ajuste que nosea DEFAULT.
A.Format
HomeEnd
Feed
19
FUNCIÓN DE MEMBRETE
La función de membrete le permite crear con rapidez y facilidad sus propios clichés paramembretes personalizados. Seleccione esta función para centrar automáticamente el texto yajustar la longitud de la cinta y los márgenes a un formato perfecto para los soportes de pelí-culas de membrete entintados. Puesto que el soporte del membrete es reutilizable, haga unnuevo cliché de membrete y reemplácelo por el que hay en el soporte de películas.
Para hacer un membrete:
1 Escriba el texto, y después inserte un casete de película de membretes de tamañomedio (3/4” (18 mm)).
2 Mantenga presionado y presione una vez. Aparecerá el mensaje“STAMP FORMAT” en el visualizador.
3 Presione . Se hará el formato del texto para un membrete: centrado dentro
del área preajustada del mensaje con la longitud y los márgenes de la cinta automá-ticamente ajustados.
4 Presione para separar el texto del cliché de membrete.
5 Presione la palanca de la cuchilla de la cinta, extraiga el papel del dorso del clichédel membrete y adhiéralo al tampón de tinta o soporte de películas.
Para adherir un membrete:
1 Extraiga el marco del membrete de entorno al lado al tampón de tinta delsoporte de películas de una vez, y saque entonces el sello protector quecubre el tampón de tinta y el papel del dorso del cliché del membrete.
2 Con el lado brillante del cliché del membrete encarado hacia arriba, alineeuno de sus extremos con la ranura del lado del soporte de películas demembrete.
3 Retenga el extremo del cliché del membrete en su lugar con el dedo pul-gar, y pase la cinta por las guías mientras la tensa bien.
4 Pliegue el otro extremo del cliché del membrete por en otro lado del sopo-rte de películas de membrete y reténgalo en su lugar con el dedo.
5 Adapte el marco del membrete encima del cliché del membrete ypresiónelo a su lugar.
6 Inserte el soporte de películas de membrete recto en su tapa.☞ Asegúrese de que el membrete quede correctamente cubierto para evitar derrames de
tinta.
Stamp
Mirror
20
FUNCIONES DE TAMAÑO Y DE ANCHURA
El tamaño de los caracteres puede ajustarse empleando las funciones de tamaño (Size) yde ancho (Wide). Puesto que el tamaño de los caracteres que puede utilizarse dependedel ancho de la cinta, la tabla siguiente indica los tamaños de caracteres que pueden uti-lizarse con cada ancho de cinta.
El ajuste del tamaño de ajuste inicial es AUTO y el ajuste inicial para el ancho es OFF. Eltamaño y el ancho actualmente seleccionados siempre se indican con los indicadores deencima del visualizador.
Con el ajuste de tamaño AUTO, la máquina compara su texto con el ancho de la cintainstalada y ajusta automáticamente los caracteres al tamaño más grande posible. Sinembargo, hay también otros seis tamaños de puntos disponibles y cada uno puede impri-mirse con caracteres anchos.
Para cambiar el ajuste del tamaño:
1 Manteniendo presionada , pulse una vez , y mantenga presionada
para hacer que se visualice el tamaño actualmente ajustado.
2 Siguiendo manteniendo presionada , continúe presionando hasta que se
visualice el tamaño actualmente ajustado mediante el indicador del mismo.
☞ El ajuste del tamaño actual también se mostrará en el indicador de tamañosituado sobre el visualizador.
3 Para aplicar el ajuste de tamaño seleccionado a todo el texto, suelte .
Para activar o desactivar la función de anchura:
1 Manteniendo presionada , pulse una vez , y mantenga presionada
para hacer que se visualice el ancho actualmente ajustado.
2 Siguiendo manteniendo presionada , continúe presionando hasta que se
visualice el ancho actualmente ajustado mediante el indicador del mismo.
3 Para aplicar el ajuste de ancho seleccionado a todo el texto, suelte .
Cuando haya seleccionado el ajuste AUTO y haya instalado una cinta de 18 mm (3/4”)de anchura, el texto se imprimirá en mayúsculas y en una sola línea con un tamaño decaracteres de 48 puntos.
Anchos de cinta Tamaños (en puntos)
1/4” (6 mm) 6, 9, 12
3/8” (9 mm) 6, 9, 12, 18
1/2” (12 mm) 6, 9, 12, 18, 24
3/4” (18 mm) 6, 9, 12, 18, 24, 36
Size
Size
Width
Width
21
FUNCIÓN DE ESTILO
Podrá seleccionar entre doce estilos de caracteres distintos que podrá aplicar a su texto.
☞ Los caracteres que se imprimen utilizando los tamaños más pequeños puedenresultar difíciles de leer si se seleccionan ciertos ajustes de estilos (por ejemplo,(I+SHADOW).
Hay disponibles los siguientes ajustes de estilos:
NORMAL
BOLD (negrilla) I+BOLD (cursiva y negrilla)
OUTLINE (perfilado) I+OUTLINE (cursiva y perfilado)
SHADOW (sombreado) I+SHADOW (cursiva y sombreado)
ITALIC (cursiva) VERTICAL
El ajuste de estilo predeterminado es NORMAL. El indicador de estilo de la parte inferiorderecha del visualizador mostrará el ajuste de estilo actual cuando seleccione un estiloque no sea NORMAL.
Consulte el apartado de Referencia, al final de esta sección, para ver muestras de los ajus-tes disponibles.
Para cambiar el ajuste del estilo:
1 Manteniendo presionada , pulse una vez , y mantenga presionada
para hacer que se visualice el estilo actualmente ajustado.
2 Siguiendo manteniendo presionada , continúe presionando hasta que se
visualice el estilo actualmente ajustado mediante el indicador del mismo.
☞ El ajuste de estilo actual se mostrará en el indicador de estilo de la esquinainferior derecha del visualizador.
3 Para aplicar el ajuste de estilo seleccionado a todo el texto, suelte .
Style
Style
22
FUNCIÓN DE SUBRAYADO
Podrá acentuar el texto subrayándolo.El ajuste de subrayado predeterminado es OFF. Cuando haya ajustado la función desubrayado a ON, el indicador de subrayado de la parte derecha del visualizador seencenderá.
Para cambiar el ajuste del subrayado:
1 Manteniendo presionada , pulse una vez , y mantenga presionada
para hacer que se visualice el subrayado actualmente ajustado.
2 Siguiendo manteniendo presionada , continúe presionando hasta que se
visualice el subrayado actualmente ajustado mediante el indicador del mismo.
☞ Cuando seleccione el ajuste ON, el indicador de subrayado se en encenderá.3 Para aplicar el ajuste de subrayado seleccionado a todo el texto, suelte .
ACTIVADO
Underline
Underline
23
FUNCIÓN DEL TIPO DE CARACTERES
Con la función del tipo de caracteres podrá seleccionar una amplia variedad de tipos decaracteres para su texto.Los ajustes de tipos de caracteres siguientes están disponibles en la PT-1800/1810:
HELSINKI, BRUSSELSEl ajuste inicial del tipo de caracteres es HELSINKI. El ajuste actualmente seleccionadodel tipo de caracteres siempre se muestra con los indicadores del tipo de caracteres dedebajo del visualizador.Consulte el apartado de Referencia, al final de esta sección, para ver muestras de los ajus-tes disponibles.Para cambiar el ajuste del tipo de caracteres:
1 Manteniendo presionada , pulse una vez , y mantenga presionada
para hacer que se visualice el tipo de caracteres actualmente ajustado.
2 Siguiendo manteniendo presionada , continúe presionando hasta que se
visualice el tipo de caracteres actualmente ajustado mediante el indicador del mismo.
☞ El ajuste actual de fuente también se mostrará mediante el indicador defuente de la parte inferior izquierda del visualizador.
3 Para aplicar el ajuste de tipo de caracteres seleccionado a todo el texto, suelte
.
REFERENCIA
Ajustes del tipo de
caractersMuestras de tipos de caracters Indicadores del
visualizador
HELSINKI Font 1
BRUSSELS Font 2
Font
Font
24
FUNCIÓN DE MARCOS
Con la función de marcos, podrá seleccionar diversos marcos y funciones destacadaspara hacer un diseño más decorativo o una etiqueta con más énfasis.Los ajustes de marcos siguientes están disponibles:
OFF, ROUND, CANDY, POINTING, NAMEPLATE, DOTEl ajuste inicial de marco es OFF, aunque hay también otros ajustes. Si se seleccionacualquier ajuste que no sea OFF, se encenderá el indicador de marco, situado a la dere-cha del visualizador.Consulte el apartado de Referencia, al final de esta sección, para ver muestras de los ajus-tes disponibles.Para cambiar el ajuste del marco:
1 Manteniendo presionada , pulse una vez , y mantenga presionada
para hacer que se visualice el marco actualmente ajustado.
2 Siguiendo manteniendo presionada , continúe presionando hasta que se
visualice el marco actualmente ajustado mediante el indicador del mismo.
☞ El indicator de marco se enciende si se selectiona un ajuste que no sea OFF.
3 Para aplicar el ajuste de marco seleccionado a todo el texto, suelte .
REFERENCIA
Ajustes del marco Muestras de marco Ajustes
del marco Muestras de marco
OFF POIN-TING
ROUND NAME-PLATE
CANDY DOT
Frame
Frame
25
FUNCIÓN DE CINTA
La función de margen cinta le permite ajustar el tamaño de los márgenes de los ladosizquierdo y derecho del texto.El ajuste inicial de margen cinta es FULL, aunque hay también disponibles otros tres ajustes.
☞ Después de imprimir una etiqueta usando el ajuste NONE de margen cinta, man-
tenga presionado y presione una vez para que la cinta avance
antes de presionar la palanca de la cuchilla de la cinta para cortarla, porque de locontrario podrían cortarse algunos de los caracteres impresos.Después de imprimir empleando los ajustes de margen cinta NARROW, y HALF,presione la palanca de la cuchilla de la cinta para cortar la etiqueta, y empleeentonces unas tijeras para cortar a lo largo de los puntos (:) impresos para centrarel texto dentro de la etiqueta.
Para cambiar el ajuste de la cinta:
1 Manteniendo presionada , pulse una vez , y mantenga presionada
para hacer que se visualice la cinta actualmente ajustado.
2 Siguiendo manteniendo presionada , continúe presionando hasta que se
visualice la cinta actualmente ajustado mediante el indicador del mismo.
3 Para aplicar el ajuste de la cinta seleccionado a todo el texto, suelte .
FULL(márgenes de 25 mm (1”))
NONE(sin márgenes)
NARROW(márgenes de 4 mm (1/6”))
HALF(márgenes de 12 mm (1/2”))
Feed
Tape
Tape
26
FUNCIÓN DE LA ALINEACIÓN HORIZONTAL
Podrá elegir alinear texto en una de las tres formas disponibles. Además, si utilizó la fun-ción de longitud para ajustar la longitud de la etiqueta, los texto se alinearán dentro de laetiqueta de acuerdo con el ajuste de alineación horizontal seleccionado.El ajuste inicial de la alineación horizontal es LEFT (izquierda), aunque también están dis-ponibles otros dos ajustes.
Para cambiar el ajuste de la alineación horizontal:
1 Manteniendo presionada , pulse una vez , y mantenga presionada
para hacer que se visualice la alineación horizontal actualmente ajustado.
2 Siguiendo manteniendo presionada , continúe presionando hasta que se
visualice la alineación horizontal actualmente ajustado mediante el indicador delmismo.
3 Para aplicar el ajuste de la alineación seleccionado a todo el texto, suelte .
LEFT RIGHT
CENTER
Align
Align
27
FUNCIÓN DE IMPRESIÓN DE ESPEJO
Con esta función, podrá imprimir el texto de modo que los caracteres puedan leersedesde el lado del adhesivo de la cinta. Si se adhieren etiquetas con impresión de espejo aun vidrio, o en otro material transparente, podrán leerse correctamente desde el ladoopuesto.
☞ Cuando emplee la función de impresión de espejo, el texto se imprimirá en cintatransparente.
El ajuste inicial para la impresión de espejo es OFF.
Para activar o desactivar la impresión de espejo:
1 Manteniendo presionada , pulse una vez , y mantenga presio-
nada para hacer que se visualice la impresión de espejo actualmente
ajustado.
2 Siguiendo manteniendo presionada , continúe presionando hasta que
se visualice la impresión de espejo actualmente ajustado mediante el indicador delmismo.
3 Para aplicar el ajuste de la impresión de espejo seleccionado a todo el texto, suelte
.
ON
Mirror
Mirror
28
LENGTH FUNCTIÓN
Aunque la longitud de la etiqueta impresa ajusta automáticamente dicha longitud deacuerdo con el texto introducido, es posible que usted desee hacer una etiqueta conuna longitud específica. La función de longitud le permitirá ajustar la longitud de la eti-queta entre 1,6” y 11,8” (4,0 cm y 30,0 cm).El ajuste predeterminado de longitud es OFF. Cuando ponga la función de longitud enON, se encenderá el indicador de longitud de la parte derecha del visualizador.☞ Si desconecta y vuelve a conectar la alimentación de la máquina, el ajuste de lon-
gitud volverá a OFF.Para activar y desactivar la función de longitud:
1 Manteniendo presionada , presione una vez , y mantenga presio-
nada hasta que se visualice brevemente la longitud actual de la etiqueta
(texto y ambos márgenes), y después haga que se visualice el ajuste de longitudde etiqueta actual (ON u OFF).
2 Manteniendo presionada , continúe presionando hasta que se
visualice el ajuste de longitud de etiqueta deseado.
☞ Cuando seleccione ON, se encenderá el indicador de longitud.
3 Suelte . Si había seleccionado ON, se visualizará la longitud actual de la
etiqueta.
4 Presione o para seleccionar la longitud deseada, o utilice las teclasnuméricas para introducir la longitud.
☞ Para cambiar las unidades (pulgadas o centímetros), presione hasta que
aparezcan las unidades deseadas.
Para cambiar la longitud en pasos de 1” (1,0 cm), mantenga pulsada o
, y después presione la tecla cuando se visualice el ajuste deseado.
5 Presione .
Length
Length
HomeEnd
Home
End
29
FUNCIÓN DE LA TECLA DE IMPRESIÓN Y AVANCE
Después de haber introducido el texto y de haber seleccionado los ajustes del formatodeseado, estará preparado para la impresión. Para imprimir una etiqueta:
● Presione una vez . Se visualizará “COPIES” y a continuación el número
de etiquetas que van a imprimirse.
☞ Después de haber impreso utilizando el ajuste de margen de cinta NONE, man-
tenga pulsada y después presione una vez para hacer que la cinta
avance antes de cortarla, ya que de lo contrario algunos caracteres no seimprimirían.
Para hacer avanzar la cinta:
● Mantenga presionado y presione una vez. La cinta avanzará
25 mm (1”) hacia afuera.
Para cortar la cinta:● Presione la cinta sobre la palanca de la cuchilla.
☞ Para evitar daños en la cinta, no trate de cortarla durante la impresión ni elavance. Si presiona demasiado la palanca de la cuchilla, puede romperse.
Mirror
Feed
Feed
30
FUNCIÓN DE NUMERACIÓN
Esta función podrá utilizarse para imprimir muchas copias del mismo texto aumen-tando en 1 cierto número en el texto después de haber impreso cada etiqueta.Para utilizar la función de numeración:1 Presione , , , o para colocar el cursor debajo del número
que desee aumentar.
2 Mantenga pulsada y presione . En el visualizador aparecerá el
mensaje “NUMBER UNTIL 1-9?”.
3 Presione una tecla numérica ( a ) correspondiente all último número
que desee imprimir.
☞ Para abandonar la función de numeración sin imprimir, mantenga pulsada
y después presione (o presione simplemente ).
4 Para comenzar la impresión de etiquetas, presione (o ). El
número de cada copia se visualizará mientras esté copiándose.
☞ Después de haber impreso utilizando el ajuste de margen NONE, mantenga
pulsada y presione una vez para hacer que la cinta avance
antes de cortarla, ya que de lo contrario algunos caracteres no se imprimi-rían.
5 Para cortar la cinta, presione la palanca del cortador de la misma, y después uti-lice unas tijeras para cortar a lo largo de los puntos a fin de separar las etiquetas.
HomeEnd
Number
Font M.Del
Number Clear
Mirror
Feed
31
FUNCIÓN DE IMPRESIÓN REPETIDA
Esta función le permite imprimir hasta 9 copias del mismo texto. Para emplear la función de impresión repetida:
1 Mantenga presionado y presione . Aparecerá el mensaje “COPIES
UNTIL 1-9?” en el visualizador.
2 Presione la tecla numérica ( a ) correspondiente al número de etiquetas
que desee.
☞ Para abandonar la función de impresión repetida sin imprimir, mantenga pul-
sada y después presione (o presione simplemente ).
3 Presione (o ) para empezar a imprimir las etiquetas. Se visualizará
el número de cada copia mientras se imprime.
☞ Después de imprimir empleando el ajuste NONE de margen cinta, mantenga
presionado y presione una vez para que avance la cinta
antes de cortarla, porque de no hacerlo así algunos caracteres impresospodrían quedar cortados.
4 Presione la palanca de la cuchilla de la cinta para cortar la cinta, y emplee luegounas tijeras para cortar a lo largo de los puntos impresos para separar las etiquetas.
Repeat
Font M.Del
Repeat Clear
Mirror
Feed
32
FUNCIONES DE LA MEMORIA
Usted podrá utilizar la memoria para almacenar sus archivos de texto más frecuente-mente utilizados. El texto permanecerá en la memoria, incluso después de haberlo elimi-
nado del visualizador utilizando la función de borrado (manteniendo presionada
y presionando ).
Cuando almacena cada archivo, a éste se le asignará un número para poder invocarlofácilmente. En la memoria podrá almacenar hasta 9 archivos de texto, o aproximada-mente 300 caracteres. Cada archivo de texto almacenado podrá tener un máximo de 99caracteres.Como, cuando se invoque un archivo de texto con la función de invocación, se invocaráuna copia del archivo almacenado, el texto podrá editar o imprimirse sin cambiar elarchivo originalmente almacenado. Cuando ya no necesite un archivo o cuando ya no lonecesite, podrá utilizar la función de borrado de la memoria. ☞ Cuando tenga que insertar nuevas pilas, hágalo antes de cinco minutos de haber
extraído las viejas, ya que de lo contrario los archivos de texto almacenados en lamemoria se perderían (a menos que la máquina esté enchufada en un tomacorri-ente de la red con el adaptador de alimentación de CA).
ALMACENAMIENTO DE TEXTOPara almacenar un archivo de texto:
1 Mantenga pulsada y presione . En el visualizador aparecerá el men-
saje “STORE SELECT 1-9?”.
☞ Si ya están almacenados 300 caracteres, en el visualizador aparecerá el men-saje de error “MEMORY FULL!”. Cuando ocurra esto, tendrá que borrar unmensaje existente antes de podere almacenar otro nuevo.
2 Presione la tecla ( a ) correspondiente al número de archivo en el que
desee almacenar texto. El texto se almacenará en el número de archivo seleccio-nado y el texto previamente mostrado en el visualizador desaparecerá.
☞ Si ya hay un archivo almacenado con el número de archivo seleccionado, enel visualizador aparecerá el mensaje “OVERWRITE?”, y usted tendrá quedecidir entre reescribir o borrar tal archivo.Para abandonar la función de almacenamiento del texto, mantenga pulsada
y presione (o simplemente presione ).
Clear
Store
Font M.Del
Store Clear
33
Par reescribir un archivo almacenado con otro nuevo:
● Presione para borrar el archivo previamente almacenado y almacenar el
nuevo con el número seleccionado.
☞ Para retroceder y elegir otro número de archivo sin reescribir el archivo de
texto, presione , y después presione una tecla numérica correspon-
diente a un número de archivo diferente.
INVOCACIÓN DE TEXTOPara invocar un archivo de texto:
1 Mantenga pulsada y presione , En el visualizador aparecerá el men-
saje “RECALL SELECT 1-9?”.
2 Presione la tecla ( a ) correspondiente al número de archivo que desee
invocar. Aparecerá el texto almacenado con el número de archivo seleccionado.
☞ Para ver otras partes del archivo de texto seleccionado, presione o
.
Para hacer que se visualice el texto almacenado en otros números de archi-
vos, presione o , o la tecla correspondiente a otro número dearchivo.Para abandonar la función de invocación sin invocar texto, mantenga pul-
sada y presione (o presione simplemente ).
3 Presione . Cualquier texto previamente introducido en el visualizador se
borrará y el texto introducido en el número de archivo seleccionado se invocará enel visualizador.
BORRADO DE UN ARCHIVOPara borrar un archivo de texto:
1 Mantenga pulsada y presione . En el visualizador aparecerá el men-
saje “CLEAR SELECT 1-9?”.
Clear
Recall
Font M.Del
HomeEnd
Recall Clear
M.Del
34
2 Presione la tecla ( a ) correspondiente al número de archivo que desee
borrar. En el visualizador aparecerá el texto almacenado con el número de archivoseleccionado.
☞ Para ver otras partes del archivo de texto seleccionado, presione o
.
Para hacer que se visualice el texto almacenado en otros números de archi-
vos, presione o , o la tecla correspondiente a otro número dearchivo.Para abandonar la función borra de la memoria sin borrar el archivo de
texto, mantenga pulsada y presione (o presione simplemente
).
3 Para borrar el archivo de texto seleccionado, presione .
Font M.Del
HomeEnd
M.Del
Clear
35
SOLUCIÓN DE PROBLEMAS
Problema Remedio
1. El visualizador se queda en blanco des-pués de haber conectado la alimenta-ción de la máquina.
• Compruebe que el adaptador de CAesté correctamente enchufado.
• Si está empleando pilas alcalinas, com-pruebe que estén correctamente inser-tadas.
• Si las pilas están gastadas, reemplácelaspor otro nuevo.
2. La máquina no imprime o los caracte-res impresos quedan borrosos.
• Compruebe que el casete de cinta sehaya insertado correctamente.
• Si el casete de cinta está vacío, reem-plácelo por otro nuevo.
• Asegúrese de que la cubierta del casetede cinta se haya cerrado.
3. Los archivos de texto almacenados enla memoria ya no están ella.
• Si las pilas están gastadas, reemplácelaspor otro nuevo.
4. Los caracteres impresos no se formancorrectamente.
• Si está empleando pilas alcalinas, qui-zás estén gastadas. Pruebe utilizando eladaptador de CA o reemplace las pilaspor otras nuevas.
5. Aparece una línea horizontal en blancoa través de la etiqueta impresa.
• Limpie el cabezal de impresión comose ha explicado en la página 12.
6. Aparecen franjas. • Se ha terminado la cinta. Reemplace elcasete de cinta por otro nuevo.
7. La máquina se ha “bloqueado” (esdecir, no responde cuando se presionauna tecla).
• Desconecte la alimentación de lamáquina, y entonces, mientras man-
tiene presionado y ,
vuelva a conectar la alimentación. Eltexto y los formatos del visualizador ytodos los archivos de texto almacena-dos en la memoria quedan borrados.
Align
36
LISTA DE MENSAJES DE ERROR
Mensaje de error Causa Remedio
3 LINE LIMIT!
• Este mensaje aparece si ya existen cuatro líneas tres pre-
siona .
• Límite el número de líneas a tres.
BATTERIES WEAK!
• Este mensaje aparece cuando las pilas alcalinas instaladas están gastadas.
• Reemplace las pilas o emplee el adaptador de CA.
BUFFER EMPTY!
• Este mensaje aparece si man-
tiene pulsada y pre-
siona , pero sin haber
introducido texto en el visua-lizador.
• Introduzca algo de texto antes de iniciar la función.
• Este mensaje aparece si intenta imprimir, pero sin haber introducido texto.
• Introduzca texto antes de la impresión.
• Este mensaje aparece si intenta almacenar archivo de texto en la memoria, pero sin haber introducido texto en el visualizador.
• Introduzca texto antes del almacenamiento.
BUFFER FULL!
• Este mensaje aparece si intenta introducir un carácter, símbolo, código de barras, retorno, o un espacio cuando ya se han introducido 99 caracteres.
• Borre algo del texto existente para poder introducir más texto.
CAN’T HERE!
• Este mensaje aparecerá si el cursor está al final del texto cuando mantenga pulsada
y presione .
• Mueva el cursor hasta debajo del número manteniendo
pulsada y presio-
nando .
Length
Number
Number
37
CHANGE ADAPTOR
• Este mensaje aparece si se está empleando un adaptador de alta tensión.
• Extraiga el adaptador de alta tensión y conecte el adapta-dor de 9,0V CA 1,2 A.
CUTTERERROR!
• Este mensaje aparecerá si presiona la palanca del corta-dor de cinta mientras esté imprimiéndose una etiqueta.
• Suelte la palanca del corta-dor de cinta.
INVAL. CHRS!
• Este mensaje aparecerá si el cursor está al final del texto cuando mantenga pulsada
y presione .
• Mueva el cursor hasta debajo del número manteniendo
pulsada y presio-
nando .
LENGTH LIMIT!
• Este mensaje aparece si el texto es más largo de 1 metro cuando trate de imprimirlo.
• Acorte el texto a menos de 1 metro antes de tratar impri-mir.
• Este mensaje aparecerá si uti-lizó la función de longitud para ajustar una longitud inferior a 1,6” (4,0 cm) o más de 11,8” (30,0 cm).
• Ajuste la longitud de la eti-queta entre 1,6” (4,0 cm) y 11,8” (30,0 cm).
• Este mensaje aparecerá si uti-lizó la función de longitud de tabulaciones para ajustar una longitud superior a 11,8” (30,0 cm).
• Ajuste la longitud de las tabu-laciones de forma que sea inferior a 11,8” (30,0 cm).
LINE LIMIT!
• Este mensaje aparece si el número de líneas del texto es mayor que el número máximo de líneas posible para la cinta instalada.
• Reduzca el número de líneas o instale una cinta más ancha.
MEMORY FULL!
• Este mensaje aparecerá si intenta almacenar un archivo de texto después de haber almacenado ya 300 caracteres en la memoria.
• Borre un archivo que no desee para dejar espacio para el nuevo.
Mensaje de error Causa Remedio
Number
Number
38
NO FILES!
• Este mensaje aparece si intenta llamar o borrar un archivo de texto de la memo-ria cuando realmente no hay ninguno almacenado.
• Almacene primero un archivo de texto.
NUMBERTOO SMALL!
• Este mensaje aparecerá si el número ajustado para impri-mirse utilizando la función de numeración es inferior al situado sobre el cursor.
• Presione la tecla correspon-diente a un número superior al del texto.
RAMPROBLEM!
• Este mensaje aparece si hay algún problema con la memoria de acceso aleatorio de la máquina.
• Póngase en contacto con su representante de servicio.
REPLACE BATTERIES!
• Este mensaje aparece cuando las pilas alcalinas instaladas están casi gastadas.
• Reemplace las pilas o emplee el adaptador de CA.
ROMPROBLEM!
• Este mensaje aparece si hay algún problema con la memoria de acceso aleatorio de la máquina.
• Póngase en contacto con su representante de servicio.
SYSTEMERROR!
• Este mensaje aparece si hay algún problema con el soft-ware de la máquina.
• Póngase en contacto con su representante de servicio.
NOTAPE!
• Este mensaje aparecerá si intenta imprimir una etiqueta o alimentar cinta cuando haya casete de cinta instalado.
• Instale un casete de cinta y pruebe de nuevo.
TABLIMIT!
• Este mensaje aparecerá si ya ha ajustado 50 tabulaciones en el texto cuando presione
.
• Limite el número de tabula-ciones del texto a 50.
TEXTTOO HIGH!
• Este mensaje aparece si el tamaño del texto es más grande que el ancho de la cinta instalada.
• Reduzca el tamaño de los caracteres o instale una cinta más ancha.
Mensaje de error Causa Remedio
Tab
39
TEXTTOO LONG!
• Este mensaje aparece si la longitud del texto es mayor que la longitud que se ha ajustado para la etiqueta utili-zando la función de longitud.
• Borre algo de texto, reduzca el ancho de los caracteres o incremente la longitud ajus-tada de la etiqueta.
Mensaje de error Causa Remedio
40
ESPECIFICACIONES
HARDWARE
SOFTWARE
Dispositivo de entrada: Teclado de 52 teclas
LCD: 7 × 5 puntos12 caracteres × 2 líneas17 indicadores
Cinta de impresión: Sensible a la presión, base adhesiva, 8 m (26´3”) de longitudCuatro anchos disponibles:
6 mm (1/4”)9 mm (3/8”)
12 mm (1/2”)18 mm (3/4”)
Alimentación: Seis pilas alcalinas AA (AM3, LR6) o adaptador de CA opcionalDesconexión automática de la alimentación si no se pulsa ninguna tecla durante 5 minutos
Cabezal de impresión: 128 puntos / 180 dpi
Dimensiones: 178 (An) × 205 (Prf) × 60 (Al) mm(7” × 8 1/6” × 2 23/63”)
Peso: 700 g (1.5 lbs) (sin casete de cinta ni pilas instalados)
Tamaño de la memoria intermedia:
Máximo de 99 caracteresUna línea – 1 mMáximo de tres líneas
Tamaño de la memoria: 300 caracteres
Tamaño de caracteres: Seis tamaños (6, 9, 12, 18, 24 y 36 puntos) + 48 puntos (Mayúsculas solamente)Todos disponibles en el modo normal y ancho (wide)
Estilos de impresión: Normal, perfilado, negrilla, sombreado (todos pueden combi-narse con cursiva), y Vertical
41
ACCESORIOS
● Accesorios de consumoAdquiera los casetes de cinta en el distribuidor autorizado que le quede más cerca. Emplee sólo cintas Brother TZ con esta máquina. Brother no puede hacerse respon-sable por los problemas causados por el empleo de accesorios de consumo no auto-rizados. No emplee cintas que no tengan la marca .
N.º de producto Descripción CANT./
PAQUETE PRECIO
Cintas laminadas de 18 mm (3/4”)
TZ-141 Caracteres negros sobre adhesivo transparente 1 $20.99TZ-145 Caracteres blancos sobre adhesivo transparente 1 $20.99TZ-241 Caracteres negros sobre adhesivo blanco 1 $20.99TZ-242 Caracteres rojos sobre adhesivo blanco 1 $20.99TZ-243 Caracteres azules sobre adhesivo blanco 1 $20.99TZ-344 Caracteres dorados sobre adhesivo negro 1 $24.99TZ-345 Caracteres blancos sobre adhesivo negro 1 $23.99TZ-441 Caracteres negros sobre adhesivo rojo 1 $20.99TZ-541 Caracteres negros sobre adhesivo azul 1 $20.99TZ-545 Caracteres blancos sobre adhesivo azul 1 $23.99TZ-641 Caracteres negros sobre adhesivo amarillo 1 $20.99TZ-741 Caracteres negros sobre adhesivo verde 1 $20.99
TZ-B41Caracteres negros sobre adhesivo naranja fluores-cente
1 $24.99
TZ-M41 Caracteres negros sobre adhesivo claro (MATE) 1 $20.99TZ-WB41 Caracteres negros sobre adhesivo Bugs Bunny 1 $23.99TZ-WT41 Caracteres negros sobre adhesivo Taz 1 $23.99TZ-WS41 Caracteres negros sobre adhesivo Tweety & Sylvester 1 $23.99
Cintas laminadas de 12 mm (1/2”)
TZ-131 Caracteres negros sobre adhesivo transparente 1 $16.99TZ-231 Caracteres negros sobre adhesivo blanco 1 $17.99TZ-232 Caracteres rojos sobre adhesivo blanco 1 $17.99TZ-335 Caracteres blancos sobre adhesivo negro 1 $20.99
Cintas laminadas de 9 mm (3/8”)
TZ-121 Caracteres negros sobre adhesivo transparente 1 $14.99TZ-221 Caracteres negros sobre adhesivo blanco 1 $16.99TZ-325 Caracteres blancos sobre adhesivo negro 1 $18.99
42
Cintas especiales
JUEGO DE MEMBRETES
TZ-421 Caracteres negros sobre adhesivo rojo 1 $16.99
Cintas laminadas de 6 mm (1/4”)
TZ-111 Caracteres negros sobre adhesivo transparente 1 $12.99TZ-211 Caracteres negros sobre adhesivo blanco 1 $14.99TZ-315 Caracteres blancos sobre adhesivo negro 1 $17.99
N.º de producto
DescripciónCANT./
PAQUETEPRECIO
TZ-SE4Caracteres negros sobre cinta de seguridad de 18 mm (3/4”)
1 $29.99
TZ-FA3Caracteres azulese sobre cinta de tela de 12 mm (1/2”)
1 $24.99
N.º de producto
DescripciónCANT./
PAQUETEPRECIO
SK-LBJuego para hacer sellos para sello con tinta negragrande
1 $39.99
SK-MBJuego para hacer sellos para sello con tinta negramedio
1 $37.99
SH-LBEstampador adicional para sello con tinta negragrande
1 $27.99
SH-MBEstampador adicional para sello con tinta negramedio
1 $24.99
N.º de producto Descripción CANT./
PAQUETE PRECIO