Pspice Report New
-
Upload
amalina-ismail -
Category
Documents
-
view
410 -
download
7
Transcript of Pspice Report New
Title : Electrical Circuit Simulation using PSpice
Objectives :
1. To analyse DC circuit using PSpice software
2. To analyse AC circuit using PSpice software
Equipments :
1. PSpice software
2. Computer
Procedures :
A. DC circuit analysis
a. Series Circuit
Figure 1
1. The circuit is shown in Figure 1 is chosen.
2. The voltages for R1, R2 and R3 are calculated.
3. Analysis the circuit by PSpice software and verify the calculation voltages.
4. Discuss the observation.
b. Parallel Circuit
Figure 2
1. The circuit is shown in Figure 2 is chosen
2. The currents through R1, R2 and R3 are calculated
3. Analysis the circuit by PSpice software and verify the calculation currents
4. Disscuss the observation.
c. Two Sources Circuit
Figure 3
1. The circuit in Figure 3 is chosen.
2. The current through R2 is calculated.
3. Analysis the circuit by PSpice software and verify the calculation current.
4. Discuss the observation.
B. AC circuit analysis
a.
Results :
A. DC circuit analysis
a. Series Circuit
i. Calculation Voltages
V 1=(R1RT )VS=( 100Ω1000Ω )10V=1V
V 2=(R2RT )VS=( 220Ω1000Ω )10V=2.2V
V 3=( R3RT )VS=( 680Ω1000Ω )10V=6.8V
ii. PSpice analysis
V 1=10V−9V=1V
V 2=9V−6.8V=2.2V
V 3=6.8V−0V=6.8V
b. Parallel Circuit
i. Calculation Currents
I 1=( VsR1 )=( 20V1.0 kΩ )=20mA
I 2=( VsR2 )=( 20V2.2kΩ )=9.09mA
I 3=( VsR3 )=( 20V560kΩ )=35.7mAii. PSpice analysis
I 1=2×10−2=20mA
I 2=9.091×10−3=9.09mA
I 3=3.571×10−2=35.7mA
c. Two Sources Circuit
i. Calculation current through R2
Step 1 : Consider 10 V alone
RT ( s1 )=R1+R32
=100Ω+50Ω=150Ω
¿ ( s1 )= Vs1RT (s1 )
= 10V150V
=66.7mA
I 2 ( s1 )=( R3R2+R3 )(s1 )=( 100Ω200Ω )66.7mA=33.3mA
Step 2 : Consider 5 V alone
RT ( s2 )=R3+ R12
=100Ω+50Ω=150Ω
¿ ( s2 )= Vs2RT (s 2 )
= 5V150V
=33.3mA
I 2 ( s2 )=( R1R1+R2 )( s2 )=( 100Ω200Ω )33.3mA=16.7mA
Step 3 : Add the values obtain from the both above steps
I 2=I 2 (s1 )+ I 2 ( s2 )=33.3mA+16.7mA=50mA
ii. PSpice analysis
I 2=5×10−2=50mA
B. AC circuit analysis
Discussion :
Suggestions for further work in the future:
1. Give the lab manual for convenience in learning.
2. Do not use red maker while writing on the whiteboard because it is unclear.
3. Use LCD projector to show how to do the experiment.
4. Use microphone to give the explanation.
Conclusion :
1. The DC circuit analysis is verified by PSpice Software.
2. The AC circuit analysis is verified by PSpice Software.
3. The PSpice Software can be used in both DC and AC circuit analysis.