Prospekte remko smart-wp_2013_en

Intelligent and

highly efficient

REMKO Smart-WP The Heat Pump Generation of the Future

Quality with systems

Cosy heat in the winter A pleasant climate in the summer

1-20

13

2

REMKO – THE CUSTOMER-ORIENTATED SYSTEM PROVIDER FOR THE WHOLE YEAR

AIR CONDITIONING

Air conditionersMobile air conditioners Comfort air conditioners Chilled water systemsChillers DehumidifiersMobile dehumidifiers Pool dehumidifiers

HEATING

Hot-air heating systemsMobile hot-air heating systems Stationary hot-air heating systems

NEW ENERGIES Heat pumpsInverter heat pumps Heat pump packages

Quality with systems

3

Product overview

Page Series

4-17 Heat pumps

4-11 Function WKF

12-13 The intelligent control Smart-Control

14-15 Technical data of Smart-WP WKF-compact

16-17 Technical data of Smart-WP WKF

18-35 Heat pump packages

18-29 Heat pump packages WKF

30-31 Solar collectors RSK

32-35 Heat pump solar packages WKF

36-37 Tank systems

38-41 Accessories

TÜV-inspected heat pumps with EHPA quality seal of approval

The Smart-WP intelligent heat pumps are listed by the European Heat Pump Association (EHPA – for-merly D-A-CH) in its seal of approval list! REMKO's inverter heat pumps thus fulfil high international standards and guarantee performance numbers you can count on!

4

Electrical drive energy

*

* Heating25%

75% free

solar energy from the air

Use energy from the air all year round

INDEPENDENT FROM OIL AND GAS

In contrast to other heating systems, the acquisition costs for a heat pump in new or old buildings pays off relatively quickly.

■ Considerably lower consumption and operating costs

■ Hardly any maintenance costs

■ No costs for chimney and chimney sweep

■ No costs for a tank

■ No costs for a tank room

■ Simple installation

The advantages of a heat pump are clear

New dimensions in terms of independence

The solar energy stored in the air is an inexhaustible source of emission-free power. Heat pumps draw the majority of the energy from the surrounding air.

75%* of the heat comes from the air, free of charge

* The ratio can vary depending on outdoor temperature and operating conditions.

Precise data for the COP value can be found in the technical data.

This works even in winter with outside temperatures below zero. Only the drive energy has to be provided by electrical power.

5

Highly efficient and energy-saving

1/3

Minimal temperature fluctuations mean energy savings

Time

Tem

pera

ture

The inverter requires only one-third of the time of conventional systems to start up

Conventional Inverter

The REMKO inverter technology saves money.

The REMKO Smart-WP represents a decision for a state-of-the-art solu-tion. Modern inverter technology makes this possible.

This pioneering technology automati-cally adapts the condenser speed vari-ably to the precise cooling or heating requirement. This exact and gentle regulation enables a particularly energy saving, efficient operation with a high seasonal performance factor in comparison to non-inverter systems.

In summary:

In the event of increased demand, the heat pump works more inten-sively, in the event of reduced de-mand the heat pump switches over to energy-saving mode.

This saves money.

MODERN INVERTER TECHNOLOGY

6

FUNCTION

Heat pump technology

The technology of the heat pump is similar to that of a refrigerator - only the principle is reversed. The heat extracted from the air is brought up to a higher temperature level in a refrigerant circuit and is then trans-ferred to the indoor unit.

Function of outdoor unit

The outdoor unit extracts heat from the air. This heat is brought up to a higher tem-perature level in a refrigerant circuit and is then transferred to the heating water in the indoor unit. The condenser speed and fan speed adapt to the precise cooling or heating requirement.

Function of indoor unit

The indoor unit transfers the heat con-tained in the refrigerant to the floor heat-ing elements or radiators installed in the building. In order to cool, the function of the heat pump is simply reversed.

Evaporation Condensation

Condensing

Decompression

Functional diagram for heating

Heat pump outdoor unit

Outdoor area

Heat pump indoor unit

Indoor area

REMKO Smart-WP

7

Heat pumps in new buildings. Independent from oil and gas.

Heat pumps for modernisation of existing buildings. Com-bination with existing heat generators.

Heat pumps in industry. The factory floor is heated and cooled through concrete core activation.

Heat pumps for the workshop office. The ideal space-saving solution.

WKF-compact series

With additional integrated 300-litre domestic water tank. All in one unit.

VERSATILE

WKF series

It couldn't be simpler. Everything is com-pletely installed in a single enclosure. Highly efficient, regulated heating circuit pump, heat exchanger, various fittings, and the regulation Smart-Control.

8

Effective domestic water preparation

An integrated 300-litre domestic water tank with a large-dimension heat exchanger is built into the unit in the WKF-compact series. For the WKF series, external storage systems are available.

Combination with floor heating, modern radiators, and wall-mounted heaters

Heat pumps are able to achieve their highest level of efficiency when combined with floor heating. With conventional modern radiators, the operat-ing costs are lower than for oil or gas heating ap-pliances. This means that cosy heating is guaran-teed even at lower outside temperatures.

Solar station

Circ

ulat

ion

Chi

lled

wat

er

Out

door

sen

sor

Inverted rectifier Photovoltaic plant

Hot water

Outdoor unit

REMKO Smart-WP indoor unit

Combination with storage systems. The interface and collection point for various energy systems

Tanks are offered in various designs and capaci-ties. With connection options for heat pump, solar plants, and domestic water preparation, the stor-age system is the interface and collection point.

Average temperatures in Germany

50

40

30

20

10

010 5 0 -5 -10 -15

Outdoor temperature °C

Ann

ual h

eati

ng p

erfo

rman

ce %

REMKO Smart-WP HEAT PUMPS THAT ADAPT TO THE SYSTEM

20 15

29%

7%1% 1%

39%

18%

5%

9

Floor heating

Pleasant climate in the summer

In hot weather the heat pump can be used for cooling. In order to so, the function of the heat pump is simply reversed. You will find air-conditioning units in the range of accessories. The air-conditioning units work on the convection principle. The technical principle of the air-con-ditioning units is simple: Air flows past the interior heat exchanger and is ei-ther heated up or cooled.

Ceiling cassettes REMKO KWD-S series

Wall-mounted units REMKO WLT-S series

Wall-mounted chests REMKO KWK series

Air-conditioning unitSolar plant

Photovoltaic plant

Combination with heat generator in bivalent operation

The heat pump can be combined with a heat generator in order to cover peak loads. This appli-ance, for example, can be a gas or oil condensing boiler that can be directly connected to the WKF indoor unit.

Combination with a REMKO RSK solar plant for economic domestic water preparation and heating support

An ideal combination for a maximum of economic efficiency and environmental protection. Direct solar energy delivers a high percentage of hot water preparation in annual average.

Optimized use of photovoltaic current

The REMKO Smart-WP can preferably be oper-ated using self-generated photovoltaic current. Less expensive current must be obtained from the mains. This saves money and decreases the dependency on current increases.

REMKO Smart-WP HEAT PUMPS THAT ADAPT TO THE SYSTEM

10

The compact class saves space and installation effort

The REMKO Smart-WP is perfectly suited for new buildings in combi-nation with floor heating. The WKF-compact does not require much space due to its compact construction. This saves space. The costs for installation are reduced by the high proportion of premounted components.

REMKO Smart-WP WKF-compact SERIES The heat pump with integrated 300-litre domestic water tank for high hot-water comfort

Profit from these advantages

■ Heating and cooling

■ Low investment costs

■ Power-modulated opera-tion due to modern inverter mode

■ Low operating costs due to high COP value (see technical data)

■ Ready for connection of solar system to domestic water supply

■ Mounting-friendly instal-lation. All connections are located at the top

■ High hot-water comfort through integrated, enamelled domestic water tank with a volume of 300 litres (BEVB 1.46 kWh/ day)

■ Intelligent Smart-Control control system. Use in intelligent Smart Grid power mains possible

■ Integrated heating circuit pump for the supply of the heating system

■ Integrated electronic bypass valve for guaranteeing the minimum medium flow rate

■ Intelligent defrost logic circuit

Housing solution with EPP

Through the consistent use of EPP moulded parts, insulation is increased and the loss of energy is minimized. In addition, considerable weight advantages result. The front consists of a lacquered design front panel.

11

WKF outdoor modules

Cosy heat in the winter, a pleasant climate in the summer

Winters are getting warmer and summers hotter. Tem-peratures of over +30°C are no longer uncommon in summer. This means that in addition to heating, cooling is taking on an ever more important role. One more rea-son to install a REMKO heat pump. In winter, the heat pump operates as an efficient heating system, whilst, in summer, the water-bearing system ensures for comfort-able air conditioning.

WKF-compact series with integrated 300-litre domestic water tank Output between 1.1 and 17.7 kW

Free choice when installing the outdoor units

You save a lot of space when installing the outdoor units externally. You can use the base-ment space for other purposes such as a party room or sauna. Outdoor installation is ideal for buildings without a basement.

12

REMKO Smart-ControlThe intelligent control system combines comfort and energy efficiency

Flexible operation

The colour display shows the respective operating status. This lets the user recognise the individual operating situ-ations more easily. The multi-talented Smart-Control can be positioned anywhere in the building, even as a remote control. The Smart-Control software with plain-text menu and CheckServ wizard supports the service personnel dur-ing commissioning and maintenance.

The multi-talented Smart-Control with its endless advantages

Integration of photovoltaic current into the system

Solar connection Integration of air-conditioning function into the system

Connection to several heat generators

The multi-talented device assumes the complete energy management

The Smart-Control system is an efficient overall system. Connection to all regenerative energies is possible. Whether heat pumps, solar energy, or photo-voltaics, anything can be integrated. Use in the Smart-Grid intel-ligent power mains is also possible.

13

Easy-to-survey, intuitive menu guidance

■ Constant function monitoring of all relevant parameters

■ Remote intervention via inter-face possible

■ Basic screen for the fast check of all frequently used functions

■ The volume flow rate auto-matically adapts to the heating requirement and optimises efficiency

■ Energy balance sheet, dia-grams, and animations via the colour display

Innovative operating concept

Software with plain-text menu and installation wizard

External data memoryOperating status via a central information button

Easy operation via softkeys and rotary knob

The multi-talented Smart-Control is designed for use in the intelligent Smart-Grid power mains.

14

REMKO Smart-WP WKF-compact series

European uality Labelfor Heat Pumps

EHPA / D-A-CH

The compact class saves space and installation effort

WKF-compact series does not require much space due to its compact construction and integrated components. In connection with floor heating, this unit is perfectly suited for new buildings. This construction saves space in the mounting area. The costs for installation are reduced by the high proportion of premounted components.

Scope of delivery

■ REMKO Smart-Control – the intelligent control system

■ Indoor unit with highly-ef-ficient, enamelled, 300-litre domestic water tank

■ Outdoor unit with inverter technology

■ Highly efficient controlled heating circuit pump

■ Industrial water set, includ-ing 3-way changeover valve

■ Dirt filter 1"

■ 2 shut-off valves 1" and thermometer

■ Safety group with SIV, automatic bleeding valve and pressure gauge

■ Outdoor sensor/immersion probe

■ Electrically controlled bypass mixer

■ Prepared for solar domestic water heating



■ Power-modulated opera-tion due to modern inverter mode


■ Ready for connection of solar system to domestic water supply

■ Mounting-friendly instal-lation. All connections are located at the top.


■ High hot-water comfort through integrated, enam-elled domestic water tank with a volume of 300 litres

■ Extremely low radiation losses of the domestic water tank BEVB 1.46 kWh/day

■ Intelligent regulation Smart-Control. Use in intelligent Smart Grid power mains is possible

■ Integrated heating circuit pump for the supply of the heating system

■ Integrated electronic bypass valve for guaranteeing the minimum medium flow rate

■ Intelligent defrost logic circuit

■ Monoenergetic operation possible through REMKO Smart-Serv or bivalent operation possible through REMKO Smart-BVT

15

Technical data

Area of use: heating 4-7 kW 8-11 kW 12-18 kW

Series WKF 85 compact WKF 120 compact WKF 180 compactDesign Single split Single split Single splitOperating mode Heating / cooling Heating / cooling Heating / coolingTesting EHPA EHPA EHPAInverter technology Series Series SeriesSystem Air / water Air / water Air / waterDomestic water preparation Series Series SeriesIntegrated domestic water tank 300 l 300 l 300 lHeating capacity min / max kW 1.1 - 9.3 2.5 - 12.5 3.1 - 17.7Heating capacity / COP for A7/W35 kW / -1) 7.97 / 4.4 9.86 / 4.4 14.02 / 4.5Heating capacity / COP for A2/W35 kW / - 1) 4.87 / 3.3 6.95 / 3.6 9.32 / 3.5Heating capacity / COP for A-7/W35 kW / -1) 4.31 / 2.8 6.14 / 2.9 8.20 / 2.9Cooling capacity min / max kW 1.6 - 9.5 3.3 - 11.9 5.5 - 14.0Cooling capacity / EER for A35/W7 kW / - 2) 5.60 / 3.0 6.79 / 2.3 12.20 / 2.6Cooling capacity / EER for A35/W18 kW / - 2) 7.47 / 3.9 5.30 / 3.7 12.77 / 3.8Cooling capacity / EER for A27/W18 kW / -2) 6.90 / 4.4 9.46 / 3.6 18.20 / 4.1External pressure loss max. (heating system) kPa 80 80 80Heat exchanger area, domestic water tank m² 3.5 3.5 3.5Service limits, heating °C -20 to +45 -20 to +45 -20 to +45Service limits, cooling °C +15 to +45 +15 to +45 +15 to +45Supply-temperature, heating water °C + 50 + 55 + 55Refrigerant R 410A R 410A R 410ARefrigerant, basic capacity kg 1.9 2.0 2.85Refrigerant connections Inch 3/8 / 5/8 3/8 / 5/8 3/8 / 5/8Max. refrigerant line length m 50 50 75Max. refrigerant line height m 30 30 30Voltage supply V/Hz 230/1~/50 230/1~/50 400/3~/50Rated power consumption for A7/W35 kW 1.85 2.26 3.18Rated current consumption for A7/W35 A 7.0 9.8 4.6Customer's fuse protection (outdoor module) A slow-acting 16 20 3x16Nominal flow rate of water at ∆t 5 K m³/h 1.38 1.7 2.4Max. operating pressure, water bar 3.0 3.0 3.0Hydraulic connection, supply/return line Inch 1“ AG 1“ AG 1“ AGSound power level LwA (outdoor module) dB(A) 64.0 67.9 68.3Sound-pressure level, LpA 1m (outdoor module) open air dB(A) 50/38/32 3) 53/42/36 3) 54/43/36 3)

Outdoor module, standard colour Grey-white Grey-white Grey-whiteDimensions indoor module Height / width / depth mm 1928/800/790 1928/800/790 1928/800/790Dimensions outdoor module Height / width / depth mm 800/880/310 1010/940/330 1430/940/330Weight indoor module / outdoor module kg 236/57 238/74 240/100Series WKF 85 compact WKF 120 compact WKF 180 compact

Ref.no. 255010 255020 255030 Serial colour of outdoor module: silver

Ref.no. 255015 255025 2550351) COP = coefficient of performance (heating capacity coefficient) according to EN 14511, TÜV-tested 2) EER = Energy efficiency ratio (cooling capacity coefficient) according to

EN 14511 3) Specification per outdoor module: distance1m/5m/10m

AccessoriesSeries WKF 85 compact WKF 120 compact WKF 180 compactREMKO Smart-Count Factory-installed calorimeter

259010

259010

259010

REMKO Smart-BVT BVT pipe assembly, 3-way changeover valve for the integra-tion of a second heat generator (max. 20 kW) without a circulation pump, bivalently alternating operation Note: No combination with REMKO Smart-Serv possible. Only in combination with buffer tank.

259011

259012

259013

REMKO Smart-Serv Intelligent provision, installed heating rod 9kW for monoenergetic operation incl. Emergency-heat operation Note: No combination with REMKO Smart-BVT possible.

259021

259022

259023

For additional accessories, see page 38

16

REMKO Smart-WP WKF series

European uality Labelfor Heat Pumps

EHPA / D-A-CH



■ Smart-Inverter power-modulated mode This saves money



■ Mounting-friendly installation, all connections are located at the top.

■ Intelligent Smart-Control control system. Use in intelligent Smart Grid power mains possible

■ Monoenergetic operation possible through REMKO Smart-Serv or bivalent operation possible through REMKO Smart-BVT

It couldn't be simpler. Everything complete in an indoor unit

Everything is installed in a single housing: Highly efficient circulation pump, heat exchanger, various fittings, and the Smart-Control system. In connection with existing storage systems, the WKF is perfect for new buildings and renovations.

Scope of delivery

■ REMKO Smart-Control – the intelligent control system

■ Indoor unit

■ Outdoor unit with inverter technology

■ Highly efficient, controlled heating circuit pump

■ Dirt filter 1"

■ 2 shut-off valves 1" and thermometer

■ Safety group with SIV, automatic bleeding valve and pressure gauge

■ Outdoor sensor/immer-sion probe

■ Electrically controlled bypass mixer

■ Prepared for solar domestic water heating

17

Technical dataArea of use: heating 4-7 kW 8-11 kW 12-18 kW 18-30 kW

Series WKF 85 WKF 120 WKF 180 WKF 180 DUODesign Single split Single split Single split Duo SplitOperating mode Heating/cooling Heating/cooling Heating/cooling Heating/coolingTesting EHPA EHPA EHPA EHPAInverter technology Series Series Series SeriesSystem Air / water Air / water Air / water Air / waterBuffer tank for hydraulic decoupling of volumetric flows optional optional optional optional3-way valve for external domestic water tank optional optional optional optionalHeating capacity min / max kW 1.1 - 9.3 2.5 - 12.5 3.1 - 17.7 6.2 - 35.4Heating capacity / COP for A7/W35 kW / -1) 7.97 / 4.4 9.86 / 4.4 14.02 / 4.5 28.04 / 4.5Heating capacity / COP for A2/W35 kW / -1) 4.87 / 3.3 6.95 / 3.6 9.32 / 3.5 18.64 / 3.5Heating capacity / COP for A-7/W35 kW / -1) 4.31 / 2.8 6.14 / 2.9 8.20 / 2.9 16.40 / 2.9Cooling capacity min / max kW 1.6 - 9.5 3.3 - 11.9 5.5 - 14.0 11.0 - 28.0Cooling capacity / EER for A35/W7 kW / - 2) 5.60 / 3.0 6.79 / 2.3 12.20 / 2.6 24.40 / 2.6Cooling capacity / EER for A35/W18 kW / - 2) 7.47 / 3.9 5.30 / 3.7 12.77 / 3.8 25.54 / 3.8Cooling capacity / EER for A27/W18 kW / -2) 6.90 / 4.4 9.46 / 3.6 18.20 / 4.1 36.40 / 4.1External pressure loss max. (heating system) kPa 80 80 80 80

Service limits, heating °C -20 to +45 -20 to +45 -20 to +45 -20 to +45Service limits, cooling °C +15 to +45 +15 to +45 +15 to +45 +15 to +45Max. supply line temperature, heating water °C + 50 + 55 + 55 + 55Refrigerant R 410A R 410A R 410A R 410ARefrigerant, basic capacity kg 1.9 2.0 2.85 2x2.85Refrigerant connections Inch 3/8 / 5/8 3/8 / 5/8 3/8 / 5/8 2 x 3/8 / 5/8Max. refrigerant line length m 50 50 75 75Max. refrigerant line height m 30 30 30 30Voltage supply V/Hz 230/1~/50 230/1~/50 400/3~/50 230/3~/50Rated power consumption for A7/W35 kW 1.82 2.22 3.09 2x3.09Rated current consumption for A7/W35 A 8.58 10.44 5.02 2x5.02Customer's fuse protection (outdoor module) A slow-acting 16 20 3x16 6x16Nominal flow rate of water at ∆t 5 K m³/h 1.38 1.7 2.4 2x2.4Max. operating pressure, water bar 3.0 3.0 3.0 3.0Hydraulic connection, supply/return line Inch 1" AG 1" AG 1" AG 1/4" AGSound power level LwA (outdoor module) dB(A) 64.0 67.9 68.3 68.3Sound pressure level LpA (outdoor module) in open air3) dB(A) 50/38/32 53/42/36 54/43/36 54/43/36 Outdoor module, standard colour Grey-white Grey-white Grey-white Grey-whiteDimensions indoor module Height / width / depth mm 500/800/500 500/800/500 500/800/500 500/800/500Dimensions outdoor module Height / width / depth mm 800/880/310 1010/940/330 1430/940/330 1430/940/330Weight indoor module / outdoor module kg 41/57 43/74 45/100 80/2 x 100Series WKF 85 WKF 120 WKF 180 WKF 180 DUO

Available from Nov. 2013Ref.no. 255040 255050 255060 255070

Serial colour of outdoor module: silver Available from Nov. 2013Ref.no. 255045 255055 255065 2550751) COP = coefficient of performance (heating capacity coefficient) according to EN 14511, TÜV-tested

2) EER = Energy efficiency ratio (cooling capacity coefficient) according to EN 14511 3) Specification per outdoor module: distance 1m/5m/10m

AccessoriesSeries WKF 85 WKF 120 WKF 180 WKF 180 DUO

REMKO Smart-Count Factory-installed calorimeter 259010 259010 259010 259010

REMKO Smart-BVT BVT pipe assembly, 3-way changeover valve for the integra-tion of a second heat generator (max. 20 kW) without a circulation pump, bivalently alternating operation Note: No combination with REMKO Smart-Serv possible. Only in combination with buffer tank.

259014 259015 259016 259017

REMKO Smart-Serv Intelligent provision, installed heating rod 9kW for monoenergetic operation, incl. Emergency-heat operation Note: No combination with REMKO Smart-BVT possible.

259024 259025 259026 259027


18

Package comprising:

HEAT PUMP PACKAGESType: Stuttgart

Heat pump package type Stuttgart for WKF 85-180 compact appliance series

If the heat pump is intended to serve as a sole heat generator, this heat pump package is the ideal solution. In connection with underfloor heating, this unit is perfectly suited for new buildings. In addition to the heating function, a cooling function can be provided when necessary. In this package, the domestic water preparation takes place in an enamelled, 300-litre domestic water tank integrat-ed into the indoor module. Due to the compact construction, the installation effort is extremely low. The highly efficiently controlled heating circuit pump in the indoor module can supply the heating circuits directly with water.

Information about government subsidies can be found under: www.bafa.de www.kfw.de www.foerderdata.de

Condensate catch pan for outdoor module with oil separator

Package comprising:

■ Indoor module with integrated 300-litre domestic water tank (BEVB 1.46 kWh/day) and outdoor module For scope of supply, see p.14

■ Condensation catch pan, including oil separator for outdoor module

19

Cooling

Hydraulic diagram for Stuttgart (example for monoenergetic operation)

Heating

Indoor module

Outdoor module

Cold water Circulation Hot water Cooling circuit Floor heating circuit

Technical data

Heat pump package, Type Stuttgart WKF 85 compact WKF 120 compact WKF 180 compactHeating capacity min / max kW 1.1 - 9.3 2.5 - 12.5 3.1 - 17.7

Cooling capacity min / max kW 1.6 - 9.5 3.3 - 11.9 5.5 - 14.0External pressure loss kPa 80 80 80Series WKF 85 compact WKF 120 compact WKF 180 compact

Ref.no. 256010 256015 256020

AccessoriesSeries WKF 85 compact WKF 120 compact WKF 180 compactREMKO Smart-Count Factory-installed calorimeter 259010 259010 259010

REMKO Smart-Serv Intelligent provision for malfunctions, installed heating rod 9kW for monoenergetic operation

259020 259020 259020

For additional accessories, see pageon page 38

Hot water Surface cooling / surface heating

20

Package comprising:

HEAT PUMP PACKAGESType: Mannheim

Heat pump package type Mannheim for WKF 85-180 compact appliance series

This heat pump package is designed for users who would like to operate the heat pump in combination with a conventional heat generator (bivalently alternating). The additional KPS 300 storage is used for the hydraulic decoupling of large medium flow rates. A cooling function for the summer can also be activated, if necessary. In this package, the domestic water preparation takes place in the 300-litre domestic water tank integrated into the indoor module. Through the compact design, installation expenses are extremely

low. The separate pump assemblies (can be ordered separately) for the HGU/HGM heating circuits are equipped with a high-efficiency pump (0-10 V) regulated in a needs-based manner.


Package comprising:

■ Indoor module with integrated 300-litre domestic water tank (BEVB 1.46 kWh/day) and outdoor module For scope of supply, see p.14


■ Buffer tank for cooling and heating water KPS 300 (300 litres)

Buffer tank for cooling and heating water KPS 300 (300 l)


21

Cooling

Hydraulic diagram for Mannheim (example for monoenergetic operation)

Heating

Indoor module

Outdoor module

Cold water Circulation Hot waterCooling circuit

Heating circuit

Floor heating circuitSecond heat generator

max. 20 kW

Technical data

Heat pump package, Type Mannheim WKF 85 compact WKF 120 compact WKF 180 compactHeating capacity min / max kW 1.1 - 9.3 2.5 - 12.5 3.1 - 17.7


Ref.no. 256025 256030 256035


REMKO Smart-BVT BVT pipe assembly, 3-way changeover valve for the integration of a second heat generator (max. 20 kW) without a circulation pump, bivalently alternating operation Note: No combination with REMKO Smart-Serv possible. Only in combination with buffer tank.

259011 259012 259013

Heating circuit pump set HGU Speed-controlled heating circuit pump group (0-10 V)/unmixed 259025 259025 259025

Heating circuit pump set HGM Speed-controlled heating circuit pump group (0-10 V)/mixed 259026 259026 259026


BivalentHot water Surface cooling / surface heating

22

Package comprising:

Buffer tank for cooling and heating water KPS 300 (300 l)

HEAT PUMP PACKAGESType: Cologne

Heat pump package type Cologne for WKF 85-180 appliance series

This heat pump package is designed for users who want heating first and foremost. The additional KPS 300 buffer tank is used for the hydraulic decoupling of large medium flow rates. A cool-ing function for the summer can also be activated, if necessary. Ddomestic water preparation takes place separately. With this heat pump package, both monoenergetic and bivalently alternating sys-tems can be accommodated. A second heat generator (oil/gas boiler without pump) can be connected directly to the indoor module.

The separate pump assemblies HGU/HGM (can be ordered separately) for the heating circuits are equipped with a high-efficiency pump (0-10 V) regulated in a needs-based manner. Information about government subsidies can be found under: www.bafa.de www.kfw.de www.foerderdata.de

Package comprising:

■ Indoor module and outdoor module For scope of supply, see p.16


■ Buffer tank for cooling and heating water KPS 300 (300 litres)


23

Indoor module

Outdoor module

Cooling circuit

Buffer tank

Heating element heating circuit

Floor heating circuit

Technical data

Heat pump package, Type Cologne WKF 85 WKF 120 WKF 180Heating capacity min. / max kW 1.1 - 9.3 2.5 - 12.5 3.1 - 17.7Cooling capacity min / max kW 1.6 - 9.5 3.3 - 11.9 5.5 - 14.0External pressure loss kPa 80 80 80Series WKF 85 WKF 120 WKF 180

Ref.no. 256040 256045 256050

AccessoriesSeries WKF 85 WKF 120 WKF 180REMKO Smart-Count Factory-installed calorimeter 259010 259010 259010


259014 259015 259016

REMKO Smart-Serv Intelligent provision for malfunctions, installed heating rod 9kW for monoenergetic operation Note: No combination with REMKO Smart-BVT possible.

259024 259025 259026

Heating circuit pump set HGU Speed-controlled heating circuit pump group (0-10 V)/unmixed 259025 259025 259025



Cooling BivalentHeating

Hydraulic diagram for Cologne (example for monoenergetic operation)

Second heat generator max. 20 kW

Surface cooling / surface heating

24

HEAT PUMP PACKAGESType: Dortmund

Heat pump package type Dortmund for WKF 85-180 appliance series

This heat pump package is for users who, in addition to the heat-ing function, also want domestic water preparation from their heat pump system. A cooling function for the summer can also be activated, if necessary. In this package, the domestic water preparation takes place in an enamelled 300-litre domestic water tank. The high-efficiency pump in the indoor module can supply

Package comprising:

3-way changeover valve, 5/4"

Tank for domestic water heating, enamelled EWS 300 (300 litres)

the heating circuits directly with water.


Package comprising:


■ Buffer tank for domestic water, enamelled EWS 300 (300 litres)

■ 3-way changeover valve

■ Condensate catch pan, including oil separator for outdoor module

■ Smart-Control control system installed at the factoryCondensate catch pan for out-

door module with oil separator

25

Hydraulic diagram for Dortmund (example for monoenergetic operation)

Heating Hot water Cooling

Indoor module

Outdoor module

Hot water

Cold water

Domestic water tank

Cooling circuitFloor heating

circuit

Technical data

Heat pump package, Type Dortmund WKF 85 WKF 120 WKF 180Heating capacity min / max kW 1.1 - 9.3 2.5 - 12.5 3.1 - 17.7Cooling capacity min / max kW 1.6 - 9.5 3.3 - 11.9 5.5 - 14.0External pressure loss kPa 80 80 80Series WKF 85 WKF 120 WKF 180

Ref.no. 256055 256060 256065



259024 259025 259026



26

Heat pump package type Düsseldorf for WKF 85-180 appliance series

This heat pump package is the ideal solution for users who, in addi-tion to the heating function, also want domestic water preparation from their heat pump system. A cooling function for the summer can also be activated, if necessary. The domestic water preparation takes place very efficiently with a 500 litre buffer tank and electroni-cally regulated fresh water station using the hygienic flow method.

Package comprising:

Buffer tank for domestic water HPS 500 (500 litres)

Fresh water station, complete with pump and flow switch

HEAT PUMP PACKAGESType: Düsseldorf

Condensate catch pan for out-door module with oil separator

The high-efficiency pump in the indoor module can supply the heat-ing circuits directly with water.

Information about government subsidies can be found under: www.bafa.de / www.kfw.de / www.foerderdata.de

Package comprising:


■ Buffer tank for domestic water HPS 500 (500 litres)

■ Electrically regulated fresh water station EFS 25 (for connection sets, see p.39)

■ 3-way changeover valve



For connection sets, see p.39

27

Hydraulic diagram for Düssedorf (example for monoenergetic operation)

Heating Hot water Cooling

Indoor module

Outdoor module

Hot waterCold water

Buffer tank

Cooling circuitFloor heating

circuit

Technical data

Heat pump package, Type Düsseldorf WKF 85 WKF 120 WKF 180Heating capacity min. / max kW 1.1 - 9.3 2.5 - 12.5 3.1 - 17.7Cooling capacity min / max kW 1.6 - 9.5 3.3 - 11.9 5.5 - 14.0External pressure loss kPa 80 80 80Series WKF 85 WKF 120 WKF 180

Ref.no. 256070 256075 256080



259024 259025 259026



28

Heat pump package type Frankfurt for WKF 85-180 appliance series

The energy-saving package is prepared for the integration of solar thermal plants or combustible solid fuel burner. With the fin-tube heat exchanger (special accessory) RWT31, collector surfaces from approx. 8 to 15 m² can be connected. The domestic water preparation takes place with a 800 litre or 1000 litre buffer tank and electronically regulated fresh water station using the hygienic flow method.

Package comprising:

Immersion probe and solar sensor

Multifunction buffer tank MPS 800 (800 litres) or MPS 1000 (1000 litres)


2 x 3-way changeover valve, 5/4"

HEAT PUMP PACKAGESType: Frankfurt


With this heat pump package, both bivalent and single energy source systems can be accommodated. The separate pump assemblies HGM (can be ordered separately) for the heating circuits are equipped with a high-efficiency pump (0-10 V) regulated in a needs-based manner.

Package comprising:


■ Multifunctional buffer tank MPS 800 (800 litres) or MPS 1000 (1000 litres)


■ 2 x 3-way changeover valve

■ Immersion probe and collec-tor sensor



29

Technical data

Heat pump package, Type Frankfurt WKF 85 WKF 120 WKF 180Heating capacity min. / max kW 1.1 - 9.3 2.5 - 12.5 3.1 - 17.7Cooling capacity min / max kW 1.6 - 9.5 3.3 - 11.9 5.5 - 14.0External pressure loss kPa 80 80 80Series WKF 85 WKF 120 WKF 180 with MPS 800Ref.no. 256085 256090 256095 with MPS 1000Ref.no. 256086 256091 256096



259014 259015 259016

REMKO Smart-Serv Intelligent provision for malfunctions, installed heating rod 9kW for monoenergetic operation Note: No combination with REMKO Smart-BVT possible.

259024 259025 259026



Hydraulic diagram for Frankfurt (example for monoenergetic operation for on-site integration into a solar plant)

Indoor module

Outdoor module

Cold water

(optional)

Floor heating circuitHot water

Hot water Heating or surface heating


Solar connection Bivalent

30

Technical data

Series RSK 25Domestic water heating/heating support YesRooftop installation YesFlat roof installation YesAwning/façade installation no

Installation typevertical, side-by-sidehorizontal, stacked (upon request)

Piping meanderingAbsorber coating highly selectiveMax. number of collectors in series 4Nominal heat capacity kW 1.9Efficiency % 79.7Total collector surface area m² 2.53Absorber surface area m² 2.35Aperture surface area m² 2.35Heat carrier content l 1.7Permissible operating pressure bar 10Max. corrugated pipe length m 25Dimensions - height/width/depth mm 2102/1202/80Weight kg 44

HEAT PUMP SOLAR PACKAGESSolar collector RSK 25

Solar collector RSK 25

With the thermal high-performance solar collectors Type RSK 25, you can operate your heating system with even greater efficiency in combination with the inverter heat pump from REMKO. With the refined workmanship and specially devel-oped heat conducting technology, a maximum amount of solar energy is utilised. The RSK 25-5 solar set with two solar collectors utilises solar en-ergy for hot-water preparation. The RSK 25-10 solar set with four solar collectors utilises solar energy for hot-water preparation and heating support. The REMKO solar sets provide unsurpassed performance in a perfectly attuned system configuration with the well-known inverter heat pump.

Cross-section of solar collector RSK 25

Depending on the solar set, the heat pump can be used for air conditioning during the summer, whereas the thermal solar system assumes the hot water preparation. The complete system is con-trolled via the REMKO Smart-Control intelligent control system. Almost every desire can be fulfilled by the REMKO heat pump solar packages.

Highly selective absorber layer

4mm glass

Absorber sheet, aluminium

Absorber tube

Mineral wool

Bronze-coloured, anodised aluminium frame

Assembly system

11 2

3

45

67

2

3

4

5

6

7

KEYMARK DIN-tested REMKO 011-7S1695 F

31

Solar set RSK 25-5

The solar set consisting of two solar collectors type RSK 25 is an efficient supplement to hot-water preparation.

Solar set RSK 25-10

The solar set consisting of four solar collectors type RSK 25 is an efficient supplement to hot-water preparation and heating support.

Solar station

Basic mounting set

Diaphragm expansion vessel

Fin-tube heat exchanger

Glycol, premixed

Immersion probe and collector sensor

Solar set consisting of:

■ 2x collectors type REMKO RSK 25 (5.06 m²)

■ Straight collector connector

■ Solar station

■ MAG 18, expansion vessel

■ Wall mount for MAG

■ Connecting hose for MAG

Solar set consisting of:

■ 4x collectors type REMKO RSK 25 (10.12 m²)

■ Straight collector connector

■ Solar station

■ MAG 25, expansion vessel

■ Wall mount for MAG

■ Connecting hose for MAG

■ Premixed glycol, 20 l

Accessories included in the solar set: (additional accessories can be found on page 31)

■ Basic mounting set

■ Expanded mounting set

■ Fin-tube heat exchanger RWT 31

■ Immersion probe and collector sensor

■ Premixed glycol, 10 l

■ Basic mounting set

■ Fin-tube heat exchang-er RWT 18

■ Immersion probe and collector sensor

32

Heat pump package type Frankfurt Solar for WKF 85-180 appliance series

The energy-savings package is prepared for the integration of the solar-thermal plant REMKO RSK 25-10 to the fin-tube heat exchanger RWT 31. The domestic water preparation takes place with a 800 litre or 1000 litre multifunction buffer tank and fresh water station using the hygienic flow method. With this heat pump package, both bivalent and single energy source systems can be accommodated. The solar set included in this package, type RSK 25-10, with a col-

Package comprising:

2 x 3-way changeover valve, 5/4"Solar set RSK 25-10

HEAT PUMP SOLAR PACKAGESType Frankfurt Solar

lector surface of 10.12 m² provides household water and heating sup-port. The separate pump assemblies HGM (can be ordered separately) for the heating circuits are equipped with a high-efficiency pump (0-10 V) regulated in a needs-based manner. Information about government subsidies can be found under: www.bafa.de / www.kfw.de www.foerderdata.de


Package comprising:


■ Solar set RSK 25-10

■ Multifunctional buffer tank MPS 800 (800 litres) or MPS 1000 (1000 litres)


■ 2 x 3-way changeover valve

■ Condensate catch pan, including oil separator for outdoor moduleMultifunction buffer tank MPS

800 (800 litres) or MPS 1000 (1000 litres)



33

Heating or surface heating

Hot water Solar connection

Indoor module

Outdoor module

Cold waterFloor heating

circuitHot water

Hydraulic diagram for Frankfurt Solar (example for monoenergetic operation with integration of the REMKO solar set RSK 25-10)

Technical data

Heat pump package, Type Frankfurt Solar WKF 85 WKF 120 WKF 180Heating capacity min. / max kW 1.1 - 9.3 2.5 - 12.5 3.1 - 17.7Cooling capacity min / max kW 1.6 - 9.5 3.3 - 11.9 5.5 - 14.0External pressure loss kPa 80 80 80Series WKF 85 WKF 120 WKF 180with MPS 800Ref.no. 256210 256215 256220with MPS 1000Ref.no. 256211 256216 256221



259014 259015 259016

REMKO Smart-Serv Intelligent provision for malfunctions, installed heating rod 9kW for monoenergetic operation Note: No combination with REMKO BVT possible.

259024 259025 259026




(optional)

Bivalent

34

Heat pump package type Stuttgart Solar for WKF 85-180 appliance series

If the heat pump is intended to serve as a sole heat generator, this heat pump package is the ideal solution. In addition to the heating function, a cooling function can be provided when nec-essary. In this package, the domestic water preparation takes place in an enamelled, 300-litre domestic water tank integrated into the indoor module. In addition, a cooling function can be provided as necessary while the thermal solar plant heats the domestic water. Through the compact design, installation expenses are extremely low. The solar set included in this pack-age, type RSK 25-5, with a collector surface of 5.06 m², is ideal for effective domestic water preparation.

Package comprising:

Type: Stuttgart Solar

HEAT PUMP SOLAR PACKAGES


Solar set RSK 25-5

Package comprising:

■ Indoor module with integrated 300-litre domestic water tank (BEVB 1.46 kWh/day) For scope of supply, see p.14

■ Solar set RSK 25-5


■ Smart-Control control system installed at the factory

35

Hot waterHeating Solar connection

Indoor module

Outdoor module

Cold water Circulation Hot waterCooling circuit

Floor heating circuit

Technical data

Heat pump package, Type Stuttgart Solar WKF 85 compact WKF 120 compact WKF 180 compactHeating capacity min. / max kW 1.1 - 9.3 2.5 - 12.5 3.1 - 17.7


Ref.no. 256225 256230 256235



259021 259022 259023


Hydraulic diagram for Stuttgart Solar (example for monoenergetic operation with integration of the REMKO solar set RSK 25-5)


Cooling

36

Unit type HPS 500 MPS 800 MPS 1000

Storage type Buffer tank Stratified storage

Height with insulation mm 1725 1785 2135

Diameter with insulation mm 850 990 990

Diameter without insulation mm 650 790 790

Tilt height without insulation mm 1670 1750 2090

Weight kg 113 157 176

Ref.no. 270300 270380 270400

Unit type KPS 300

Height with insulation mm 1797

Diameter mm 600

Tilt height without insulation mm 1835

Weight kg 125

Ref.no. 270250

TANK SYSTEMS

Heating water buffer tank

■ Universally usable as parallel buffer (hydraulic switch) or series-connected buffer

■ With dummy flange cover D240 for retrofitting a fin-tube heat exchanger RWT 31

■ Electrical immersion heating element, screw-in 6/4"

■ Max. operating temperature 95°C

■ Max. operating pressure 3 bar

■ Test pressure 4.5 bar

■ External anti-rust coating

■ 9 connecting thread (11 for MPS800/MPS1000) 6/4" IG with inflow restrictors

■ 4 socket screw threads 1/2" for sensor/thermometer immersion sleeves

■ From quality steel S235 according to DIN EN 10 025/10 111

■ High-efficiency, double-shell heat insulation, 100 mm, silver grey

Hot / cold water storage tanks

■ Universally usable as parallel buffer (hydraulic switch) or serial buffer

■ With cleaning flange lid D180 for retrofitting

■ Fin-tube heat exchanger RWT 18, can be retrofitted

■ Electrical immersion heating element, screw-in 6/4"

■ Operating temperature: min. 0°C, max. 95°C


■ Steel sheet inner boiler S235 according to DIN EN 10 025/10 111

■ 4 connecting threads AG 5/4"

■ Powder-coated steel sheet outer casing in silver-grey

■ Outer casing reinforced by beading

■ High-quality PUR insulation 50 mm (CFC, HCFC and HFC-free), water vapour diffusion tight

■ Sensor conduct for variable sensor positioning

37

Fin-tube heat exchanger

For additional indirect heating, e.g. with a solar thermal system

Unit type RWT 18 RWT 31

Suitable for buffer tanks

Type EWS 300 KPS 300

HPS 500 MPS 800 MPS 1000

Heat exchanger surface m² 1.40 3.10

Installation length in mm 440 530

Connection G Inch 3/4 1

Volume l 1.50 2.50

Flange Ø 180 / 8-hole 240 / 12-hole Ref.no. 260200 260210

Unit type EWS 300Height mm 1435Diameter mm 680Tilt height mm 1595Weight kg 170 Ref.no. 270100

NEW INSULATION

UP TO 21%

ENERGY SAVINGS

Electrical booster heating 6 kW for KPS/MPS/HPS storage tank

Electrical auxiliary heater 6/4" for installation in a buffer tank. Including temperature regulator and safety temperature limiter. 2, 4 or 6 kW can be optionally connected.

Ref.no. 260063

Built-in flange heating for EWS 300

Consisting of a high-quality tubular heating element fitted onto an insulated flange plate. A protective current discharge resistor, thermal sen-sor, and safety temperature limiter are included. Max. operating pressure 10 bar. Heating capacity 6 kW. Note: Not suited for buffer tanks of the HPS/MPS/KPS series.

Ref.no. 260160

Tank systems

■ Built-in flange heating (legionella protection) or fin-tube heat exchanger RWT 18 can be retrofitted

■ Enamelled with double-coiled smooth-tube heat exchanger and particularly large heat exchanger surface of 3.5 m²

■ Inner container with mag-nesium protection anodes according to DIN 4753

■ PUR insulation 50 mm (CFC, HCFC and HFC-free)


■ Max. operating temperature 95°C

Storage tank for domestic water heating

■ Connection possibilities for circulation 3/4" AG

■ Cold water supply and hot water outlet 1" IG

■ With cleaning flange cover D180

STORAGE TANK SYSTEM - ACCESSORIES

38

REMKO Smart-Control remote control

With the cabled remote control, all functions of the heat pump and heating circuits can be set. A room temperature controlled regulation of the heating circuits (FBH or radiators) can be realised. In addition, dew point control is integrated.

Ref.no. 248105

Indoor module

Electrical condensation drainage - heating

Electrical condensate drainage heating, temperature-regulated for the safe discharge of defrost water with outside temperatures below the freezing point.Ref.no. 260045

Outdoor module

Floor bracket

Floor bracket with vibration damper for outdoor module, length 1 m WKF 85-180, WKF 180 Duo (2x)

Ref.no. 260020

THE FINELY-MATCHED ACCESSORY RANGE FOR INVERTER HEAT PUMPS

Connecting line between outdoor and indoor module for WKF 85-180, 180 Duo

38 5

8 " Ø

Ref.no. 260010 /m

Condenswater drip tray including oil separator

Condensate catch pan made of stainless steel for outdoor module, including temperature-controlled electronic condensate catch pan heating, leaf guard grating, and oil separator.

Ref.no. 260125

Wall bracket set for the wall mounting of the outdoor module

For model Type Ref.no. WKF85, WKF85 WKM560 260085WKF120, WKT120 WKM560 260085WKF180, WKT180 WKM560+ 260078CMF180 Duo (2x) WKM560+ 260078Sound insulation set 1613900

39

Fresh water systems

Pulse generator

Pulse generator for the realisation of a pulse-controlled circulation pump via REMKO Smart-Control.

Ref.no. 259045

Tank connection set for buffer tanks

For the direct connection of the fresh water station EFS 25 to the buffer tank.

For buffer tank Ref.no. HPS 500 259040MPS 800 259041MPS 1000 259042

Electronically regulated fresh water station EFS 25For hygienic domestic water preparation in combination with buffer tanks. Complete with electronic control, speed-controlled high-efficiency pump, flow switch, and plate heat exchanger. Heat exchanger for high flow rate of 25 l/min., ready for mounting with EPP housing. Suited for mounting to the buffer tank or wall.

Ref.no. 260155 EFS 25

Return layering set RES for EFS 25 for connection to the buffer tankRES including tank connection pipes and 3-way changeover valve for temperature-dependent layering in the buffer tank.

For buffer tank Ref.no. HPS 500 259030MPS 800 259031MPS 1000 259032

Pump with tube assembly

Adjustable high-efficiency circulation pump including tube assembly for direct connec-tion to the EFS 25.

Ref.no. 259052

40

THE FINELY-MATCHED ACCESSORY RANGE FOR INVERTER HEAT PUMPS

Hydraulics

Overflow protection valve

Overflow protection valve 1" for ensur-ing that the minimum medium flow rate is maintained.

Ref.no. 260080

Contact probe

Contact probe for the integration of the following: - a temperature-controlled circulation pump via Smart-Control - a heating circuit with mixer (2 pcs. required)

Ref.no. 259060

Immersion probe

Immersion probe for integrating the following: - solar reference sensor for buffer tank - domestic water tank EWS 300 - general buffer sensor

Ref.no. 259062

Collector sensor

Immersion probe for the integration of solar thermal plants

Ref.no. 260102


Electrical changeover valve/3-way valve 5/4" for domestic water preparation and separate cooling circuit (four-tube system).

Ref.no. 260072


Electrical changeover valve/3-way valve 6/4" for domestic water preparation and separate cooling circuit (four-tube system) for WKF 180 DUO

Ref.no. 259055

Heating circuit pump set HGU

Consisting of a speed-controlled (0-10 V) heating circuit pump without mixer, ball valves with thermometer

Ref.no. 259035

Heating circuit pump set HGM

Consisting of a speed-controlled (0-10 V) heating circuit pump with mixer, ball valves with thermometer, 2x contact sensors

Ref.no. 259036

41

RANGE OF ACCESSORIES FOR SOLAR COLLECTORS

Solar

3-way changeover valve Solar, 1"

Electrical changeover valve/3-way valve 1" for thermal solar plants (included in the heat pump solar package)

Ref.no. 260800

Collector connector, straight

For the connection of the solar collectors RSK 25 (included in the REMKO solar set)

Ref.no. 260810

Glycol

Heat transfer medium with corrosion protection for solar plants (included in the REMKO solar set)

Ref.no. 260805 10 LRef.no. 260806 20 L

Installation coupling for the collector line

For the connection of the corrugated solar pipe to the RSK 25 solar collectors (included in the corrugated pipe mounting set)

Ref.no. 260865

Flat roof installation set for solar collectors

RSK 25-5, consisting of: 3x flat roof brackets, 1x safety supportRef.no. 260842

RSK 25-10, consisting of: 5x flat roof brackets, 1x safety supportRef.no. 260843

Corrugated pipe for solar collectors with Aerogel insulation for RSK 25-5 and RSK 25-10Design Ref.no.10 m roll, incl. installation set 26086615 m roll, incl. installation set 26086720 m roll, incl. installation set 260868Corrugated pipe, m (max. 25 m) 260869Installation set, loose 260870

Complete rooftop anchor set for solar collectors

For solar package For tile type Ref.no.RSK 25-5 Frankfurter tile 260850RSK 25-10 Frankfurter tile 260855RSK 25-5 Crown tile 260851RSK 25-10 Crown tile 260856RSK 25-5 Slate 260852RSK 25-10 Slate 260857RSK 25-5 Rafter-independent 260853RSK 25-10 Rafter-independent 260858 Slate tileCrown tileFrankfurter tile

42

THE NEW ONLINE HYDRAULICS SYSTEM CONFIGURATORThe planning of REMKO heat pumps made easy

The hydraulics configurator, a simple and free tool for generating an indi-vidual hydraulic diagram for heat pumps in only five steps, is available on www.REMKO.de.

Test it...

www.remko.de/hydraulikkonfigurator

43

General terms and conditions of business and delivery

All deliveries are subject to our general terms and conditions of business and delivery. We cannot recognise regulations of the customer that deviate from these conditions, even if we do not reject them outright.

Price

All of the s given in this list are subject to the statutory value added tax. The listed s are non-binding guideline s. We reserve the right to make changes to our product range as well as the design, construction and s of our products. All previous lists are invalidated by this list.

Copyright

To be reproduced only with written permission.

For orders under 50.00, there is an additional processing surcharge of 5.00.

Please understand that we must calculate a processing surcharge of 5.00 for an order value under 50.00.

NOTESPackaging

We use environmentally friendly packaging. This package can be returned without a problem to all waste disposal companies connected to INTERSEROH. We can inform you of a waste disposal company near you.

Disposal costs are not included in our s. These costs must be borne by the purchaser.

Payment

Payment within 8 days of the invoicing date with 2% discount or net within 30 days.

Payment for initial delivery (for new customers) is subject to a 3% discount upon delivery.

Pickup

Im Seelenkamp 12, 32791 Lage

Monday through Thursday 8:00 am to 12:00 pm and 1:00 pm to 5:00 pm

Friday 8:00 am to 3:30 pm

Orders

Telephone orders +49-5232-606-0

One of our employees will be pleased to take your order. After business hours, you can leave or-ders on our answering machine.

Fax orders +49-5232-606-260

E-mail: [email protected] URL: www.remko.de

Please do not forget your address and customer number.

Returns / exchange

Exchanges and returns are not possible.

Delivery

The delivery takes place ex works or freight collect, includ-ing packaging. We reserve the right to make a partial delivery, insofar as it seems advanta-geous for fast settlement.

REMKO INTERNATIONAL...and right in your own location too!Take advantage of our experience and advice

Hotline

Within Germany 05232-606-0

International +49-5232-606-130

REMKO GmbH & Co. KG Air Conditioning and Heating Technology

Im Seelenkamp 12 · 32791 LagePO Box 1827 · 32777 LageTelephone +49-5232-606-0Fax +49-5232-606-260E-mail [email protected] www.remko.de

Your REMKO dealer

GS/

RI/2

/3.1

3 W

e re

serv

e th

e rig

ht to

tech

nica

l mod

ifica

tions

. Inf

orm

atio

n pr

ovid

ed w

ithou

t gua

rant

ee!

Prospekte remko smart-wp_2013_en

Business

Transcript of Prospekte remko smart-wp_2013_en