PROPOSED CSIR INNOVATION COMPLEX, MUMBAI Total Sl.No … · 2014-05-27 · DSR Code No_ 2013...
Transcript of PROPOSED CSIR INNOVATION COMPLEX, MUMBAI Total Sl.No … · 2014-05-27 · DSR Code No_ 2013...
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.NoDSR Code
No_ 2013Description
Total
Qty.Unit Rate Rate In Words DSR-Amount
1.0 EARTH WORK
1.1 1.1.2Carriage of good earth by mechanical transport including loading, unloading and
stacking
1.1.2 (upto 1 KM) 2283 cum 101.27
Rupees One Hundred One
and Paise Twenty Seven
Only
231199
1.2 2.8
Earth work in excavation by mechanical means (Hydraulic excavator) / manual
means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm
on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m,
including getting out the excavated soil and disposal of surplus excavated soil as
directed, within a lead of 50 m.
2.8.1 All kinds of soil. 3805 cum 148.25
Rupees One Hundred
Forty Eight and Paise
Twenty Five Only
564091
1.3 2.25
Filling available excavated earth (excluding rock) in trenches, plinth, sides of
foundations etc. in layers not exceeding 20cm in depth, consolidating each
deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.
1522 cum 101.50Rupees One Hundred One
and Paise Fifty Only 154483
1.4 2.26Extra for every additional lift of 1.5 m or part thereof in excavation /banking
excavated or stacked materials.
a) 2.26.1 All kinds of soil 855 cum 41.75Rupees Forty One and
Paise Seventy Five Only 35696
b) 2.26.1 All kinds of soil 855 cum 83.50Rupees Eighty Three and
Paise Fifty Only 71393
c) 2.26.1 All kinds of soil 100 cum 250.50Rupees Two Hundred Fifty
and Paise Fifty Only 25050
1.5 2.32Clearing grass and removal of the rubbish upto a distance of 50 m outside the
periphery of the area cleared.45 100 sqm 296.80
Rupees Two Hundred
Ninety Six and Paise
Eighty Only
13421
1.6 2.34 Supplying chemical emulsion in sealed containers including delivery as specified.
2.34.1 Chlorpyriphos/ Lindane emulsifiable concentrate of 20% 719 litre 185.95
Rupees One Hundred
Eighty Five and Paise
Ninety Five Only
133605
CIVIL WORK
Page 1 of 66
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.NoDSR Code
No_ 2013Description
Total
Qty.Unit Rate Rate In Words DSR-Amount
1.7 2.35Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-
termite treatment (excluding the cost of chemical emulsion) :
2.35.3
Treatment of soil under existing floors using chemical emulsion @ one litre per
hole, 300 mm apart including drilling 12 mm diameter holes and plugging with
cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor :
2.35.3.1 With Chlorpyriphos/Lindane E.C. 20% with 1% concentration. 2874 sqm 107.85
Rupees One Hundred
Seven and Paise Eighty
Five Only
309961
1.8 2.27Supplying and filling in plinth with Jamuna sand under floors including,
watering, ramming consolidating and dressing complete.1724 cum 843.65
Rupees Eight Hundred
Forty Three and Paise
Sixty Five Only
1454790
2.0 CONCRETE WORKS
2.1 4.1Providing and laying in position cement concrete of specified grade excluding the
cost of centering and shuttering - All work up to plinth level :
a ) 4.1.3 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) 79 cum 4921.70
Rupees Four Thousand
Nine Hundred Twenty One
and Paise Seventy Only
388814
2.2 4.19
Providing and laying in position ready mixed plain cement concrete, using fly ash
and cement content as per approved design mix and manufactured in fully
automatic batching plant and transported to site of work in transit mixer for all
leads, having continuous agitated mixer, manufactured as per mix design of
specified grade for plain cement concrete work, including pumping of R.M.C.
from transit mixer to site of laying and curing, excluding the cost of centering,
shuttering and finishing, including cost of curing, admixtures in recommended
proportions as per IS : 9103 to accelerate/ retard setting of concrete, improve
workability without impairing strength and durability as per direction of the
Engineer - in - charge.
Note : 1) Excess/less cement used than specified in this item is payable/
recoverable separately.
2) Fly ash conforming to grade I of IS 3812 (Part-1) only be used as part
replacement of OPC as per IS : 456. Uniform blending with cement is to be
ensured in accordance with clauses 5.2 and 5.2.1 of IS: 456 -2000 in the items
of BMC and RMC.
3) The above item shall be used judiciously where specified quality of Fly Ash is
available for mixing in concrete. Also, the guidelines issued by CDO, CPWD,
vide circular no. CDO/SE(RR)/Fly Ash (Main)/102 dated 9th April 2009 shall be
followed in such cases.
All works upto plinth level.
Page 2 of 66
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.NoDSR Code
No_ 2013Description
Total
Qty.Unit Rate Rate In Words DSR-Amount
2.2.1 4.19.1.2M-10 grade plain cement concrete (cement content considered @ 220 kg/cum ).
131 cum 5262.10
Rupees Five Thousand
Two Hundred Sixty Two
and Paise Ten Only
689019
2.3 4.17
Making plinth protection 50 mm thick of cement concrete 1:3:6 (1 cement:3
coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick
bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and
grouted with fine sand, including finishing the top
158 sqm 378.95
Rupees Three Hundred
Seventy Eight and Paise
Ninety Five Only
59685
3.0 REINFORCED CEMENT CONCRETE WORK
FORM WORK
3.1 5.9Centering and shuttering including strutting, propping etc. and removal of form
for :
a ) 5.9.1 Foundations, footings, bases of columns, etc. for mass concrete 2854 sqm 186.40
Rupees One Hundred
Eighty Six and Paise Forty
Only
531986
b ) 5.9.2Walls (any thickness) including attached pilasters, butteresses, plinth and string
courses etc.1550 sqm 334.50
Rupees Three Hundred
Thirty Four and Paise Fifty
Only
518475
c ) 5.9.3Suspended floors, roofs, landings, balconies and access platform
14174 sqm 371.80
Rupees Three Hundred
Seventy One and Paise
Eighty Only
5269893
d ) 5.9.4 Shelves (Cast in situ) 60 sqm 371.80
Rupees Three Hundred
Seventy One and Paise
Eighty Only
22308
e ) 5.9.5Lintels, beams, plinth beams, girders, bressumers and cantilevers
4113 sqm 309.80
Rupees Three Hundred
Nine and Paise Eighty
Only
1274207
f ) 5.9.6 Columns, Pillars, Piers, Abutments, Posts and Struts 7500 sqm 423.00
Rupees Four Hundred
Twenty Three and Paise
Zero Only
3172500
Page 3 of 66
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.NoDSR Code
No_ 2013Description
Total
Qty.Unit Rate Rate In Words DSR-Amount
g ) 5.9.7 Stairs, (excluding landings) except spiral-staircases 451 sqm 375.65
Rupees Three Hundred
Seventy Five and Paise
Sixty Five Only
169505
h ) 5.9.16 Edges of slabs and breaks in floors and walls.
5.9.16.1 Under 20cms wide 1568 metre 111.70
Rupees One Hundred
Eleven and Paise Seventy
Only
175146
i ) 5.9.19 Weather shade, chajjas, corbels etc. Including edges. 314 sqm 468.20
Rupees Four Hundred
Sixty Eight and Paise
Twenty Only
146828
3.2 5.11
Extra for additional height in centering, shuttering where ever required with
adequate bracing, propping etc. including cost of de-shuttering and decentering
at all levels, over a height of 3.5 m, for every additional height of 1 metre or part
thereof (Plan area to be measured)
5.11.1Suspended floors, roofs, landing, beams and balconies (Plan area to be
measured). 14274 sqm 145.60
Rupees One Hundred
Forty Five and Paise Sixty
Only
2078294
3.3 STEEL REINFORCEMENT
5.22 & 5.22A
Steel reinforcement for R.C.C. work including straightening, cutting, bending,
placing in position and binding all complete upto plinth level and above plinth
level..
5.22.6 Thermo-Mechanically Treated bars 996964 kilogram 66.50Rupees Sixty Six and
Paise Fifty Only 66298076
3.4 5.30Add for plaster drip course/ groove in plastered surface or moulding to R.C.C.
projections.1568 metre 27.85
Rupees Twenty Seven and
Paise Eighty Five Only 43669
3.5 5.33
Providing and laying in position machine batched and machine mixed design mix
M-25 grade cement concrete for reinforced cement concrete work, using cement
content as per approved design mix, including pumping of concrete to site of
laying but excluding the cost of centering, shuttering, finishing and
reinforcement, including admixtures in recommended proportions as per IS:
9103 to accelerate, retard setting of concrete, improve workability without
impairing strength and durability as per direction of Engineer-in-charge.
(Note :- Cement content considered in this item is @ 330 kg/cum. Excess/less
cement used as per design mix is payable/recoverable separately).
Page 4 of 66
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.NoDSR Code
No_ 2013Description
Total
Qty.Unit Rate Rate In Words DSR-Amount
a ) 5.33.1 All works upto plinth level 1164 cum 5704.45
Rupees Five Thousand
Seven Hundred Four and
Paise Forty Five Only
6641976
b ) 5.33.2 All works above plinth level upto floor V level 5056 cum 6353.00
Rupees Six Thousand
Three Hundred Fifty Three
and Paise Zero Only
32120266
3.6 5.34 Extra for providing richer mixes at all floor levels.
Note : Excess/less cement over the specified cement content used is
payable/recoverable separately).
3.6.1 5.34.1Providing M-30 grade concrete instead of M-25 grade BMC/RMC. (Note :
cement content considered in M-30 is @ 340kg/cum).6220 cum 64.15
Rupees Sixty Four and
Paise Fifteen Only 399030
3.6.2 5.34.3Providing M-40 grade concrete instead of M-25 grade BMC/RMC.(Note : Cement
content considered in M-40 is @ 360 kg/cum)1003 cum 192.50
Rupees One Hundred
Ninety Two and Paise Fifty
Only
193158
3.7 5.35
Add for using extra cement in the items of design mix over and above the
specified cement content therein. 0 Quintal 619.65
Rupees Six Hundred
Nineteen and Paise Sixty
Five Only
0
3.8 5.38Extra for R.C.C./B.M.C./R.M.C. work above floor V level for each four floors or
part thereof.3110 cum 174.20
Rupees One Hundred
Seventy Four and Paise
Twenty Only
541786
3.9 5.44
Providing and fixing of expansion joint system related with floor location as per
drawings and direction of Engineer-In-Charge. The joints system will be of
extruded aluminum base members, self aligning / self centering arrangement
and support plates etc. as per ASTM B221-02. The system shall be such that it
provides floor to floor /floor to wall expansion control system for various vertical
localtion in load application areas that accommodates multi directional seismic
movement without stress to it's components. System shall consist of metal
profiles with a universal aluminum base member designed to accommodate
various project conditions and finish floor treatments. The cover plate shall be
designed of width and thickness required to satisfy projects movement and
loading requirements and secured to base members by utilizing manufacturer's
pre-engineered self-centering arrangement that freely rotates / moves in all
directions.
The Self -centering arrangement shall exhibit circular sphere ends that lock and
slide inside the corresponding aluminum extrusion cavity to allow freedom of
movement and flexure in all directions including vertical displacement. Provision
of Moisture Barrier Membrane in the Joint System to have watertight joint is
mandatory requirement all as per the manufactures design and as approved by
Engineer -in-Charge . (Material shall confirm to ASTM 6063.)Page 5 of 66
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.NoDSR Code
No_ 2013Description
Total
Qty.Unit Rate Rate In Words DSR-Amount
3.9.1 5.44.1 Floor Joint of 100 mm gap 342 metre 6334.05
Rupees Six Thousand
Three Hundred Thirty Four
and Paise Five Only
2166245
3.10 5.46.1
Providing and fixing of expansion joint system of approved make and
manufactures for various roof locations as per approved drawings and direction
of Engineer-In-Charge. The joints shall be of extruded aluminum base members
with, self aligning and self centering arangement support plates asper ASTM
B221-02. The system shall be such that it provides watertight roof to roof/roof to
corner joint cover expansion control system that is capable of accommodating
multidirectional seismic movement without stress to its components. System
shall consist of metal profile that incorporates a universal aluminum base
member designed to accommodate various project conditions and roof
treatments. The cover plate shall be designed of width and thickness required to
satisfy movement and loading requirements and secured to base members by
utilizing manufacturer's pre-engineered self-centering arrangement that freely
rotates / moves in all directions.
The Self centering arrangement shall exhibit circular sphere ends that lock and
slide inside the corresponding aluminum extrusion cavity to allow freedom of
movement and flexure in all directions including vertical displacement. The Joint
System shall resists damage or deterioration from the impact of falling ice,
exposure to UV, airborne contaminants and occasional foot traffic from
maintenance personnel. Provision of Moisture Barrier Membrane in the Joint
System to have water tight joint is mandatory requirement. Material shall confirm
to ASTM 6063.
3.10.1 5.46.1 Roof Joint of 100 mm gap 342 metre 6334.05
Rupees Six Thousand
Three Hundred Thirty Four
and Paise Five Only
2166245
4.0 BRICK WORK
4.1 6.34
Brick work with non modular fly ash lime bricks (FALG Bricks) conforming to
IS:12894-2002, class designation 10 average compressive strength in super
structure above plinth level up to floor V level in :
6.34.2 Cement mortar 1:6 (1 cement : 6 Coarse sand) 2286 cum 5124.05
Rupees Five Thousand
One Hundred Twenty Four
and Paise Five Only
11713273
4.2 6.5Extra for brick work / AAC block masonry / Tile brick masonry in superstructure
above floor V level, for each four floors or part thereof by mechanical means.1143 cum 263.30
Rupees Two Hundred
Sixty Three and Paise
Thirty Only
300944
HALF BRICK MASONRY
Page 6 of 66
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.NoDSR Code
No_ 2013Description
Total
Qty.Unit Rate Rate In Words DSR-Amount
4.3 6.45
Half brick masonry with non modular fly ash lime Gypsum bricks (FALG bricks)
class designation 10, conforming to IS : 12894, in super structure above plinth
and upto floor V level.
6.45.1 Cement mortar 1 : 3 (1 cement : 3 coarse sand) 2982 sqm 663.85
Rupees Six Hundred Sixty
Three and Paise Eighty
Five Only
1979376
4.4 6.14Extra for half brick masonry in superstructure, above floor V level for every four
floors or part thereof by mechanical means.1491 sqm 23.35
Rupees Twenty Three and
Paise Thirty Five Only 34811
4.5 6.15Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every
third course of half brick masonry.2982 sqm 69.50
Rupees Sixty Nine and
Paise Fifty Only 207225
5.0 WALL CLADDING
5.1 26.1
Providing and supplying aluminium extruded tubular and other aluminium
sections as per the architectural drawings and approved shop drawings , the
aluminium quality as per grade 6063 T5 or T6 as per BS 1474,including super
durable powder coating of 60-80 microns conforming to AAMA 2604 of required
colour and shade as approved by the Engineer-in-Charge.
21048 kg 338.25
Rupees Three Hundred
Thirty Eight and Paise
Twenty Five Only
7119648
(The item includes cost of material such as cleats, sleeves, screws etc.
necessary for fabrication of extruded aluminium frame work. Nothing extra shall
be paid on this account).
Page 7 of 66
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.NoDSR Code
No_ 2013Description
Total
Qty.Unit Rate Rate In Words DSR-Amount
5.2 26.2
Designing, fabricating, testing, protection, installing and fixing in position semi
(grid) unitized system of structural glazing (with open joints) for linear as well as
curvilinear portions of the building for all heights and all levels, including:
1754 sqm 2466.80
Rupees Two Thousand
Four Hundred Sixty Six
and Paise Eighty Only
4326866
a) Structural analysis & design and preparation of shop drawings for the
specified design loads conforming to IS 875 part III (the system must passed the
proof test at 1.5 times design wind pressure without any failure), including
functional design of the aluminum sections for fixing glazing panels of various
thicknesses, aluminium cleats, sleeves and splice plates etc. gaskets, screws,
toggles, nuts, bolts, clamps etc., structural and weather silicone sealants,
flashings, fire stop (barrier)-cum-smoke seals, microwave cured EPDM gaskets
for water tightness, pressure equalisation & drainage and protection against fire
hazard including:
b) Fabricating and supplying serrated M.S. hot dip galvanised / Aluminium alloy
of 6005 T5 brackets of required sizes, sections and profiles etc. to accommodate
3 Dimentional movement for achieving perfect verticality and fixing structural
glazing system rigidly to the RCC/ masonry/structural steel framework of building
structure using stainless steel anchor fasteners/ bolts, nylon seperator to prevent
bimetallic contacts with nuts and washers etc. of stainless steel grade 316, of the
required capacity and in required numbers.
c) Providing and filling, two part pump filled, structural silicone sealant and one
part weather silicone sealant compatible with the structural silicone sealant of
required bite size in a clean and controlled factory / work shop environment ,
including double sided spacer tape, setting blocks and backer rod, all of
approved grade, brand and manufacture, as per the approved sealant design,
within and all around the perimeter for holding glass.
d) Providing and fixing in position flashings of solid aluminium sheet 1 mm thick
and of sizes, shapes and profiles, as required as per the site conditions, to seal
the gap between the building structure and all its interfaces with curtain glazing
to make it watertight.
Page 8 of 66
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.NoDSR Code
No_ 2013Description
Total
Qty.Unit Rate Rate In Words DSR-Amount
e) Making provision for drainage of moisture/ water that enters the curtain
glazing system to make it watertight, by incorporating principles of pressure
equalization, providing suitable gutter profiles at bottom (if required), making
necessary holes of required sizes and of required numbers etc. complete. This
item includes cost of all inputs of designing, labour for fabricating and installation
of aluminium grid, installation of glazed units, T&P, scaffolding and other
incidental charges including wastages etc., enabling temporary structures and
services, cranes or cradles etc. as described above and as specified. The item
includes the cost of getting all the structural and functional design including shop
drawings checked by a structural designer, dully approved by Engineer-in-
charge. The item also includes the cost of all mock ups at site, cost of all
samples of the individual components for testing in an approved laboratory, field
tests on the assembled working structural glazing as specified, cleaning and
protection till the handing over of the building for occupation. In the end, the
Contractor shall provide a water tight structural glazing having all the
performance characteristics etc. all complete as required, as per the
Architectural drawings, as per item description, as specified, as per the approved
shop drawings and as directed by the Engineerin-Charge.
Note:- 1. The cost of providing extruded aluminium frames, shadow boxes,
extruded aluminium section capping for fixing in the grooves of the curtain
glazing and vermin proof stainless steel wire mesh shall be paid for separately
under relevant items under this subhead. However, for the purpose of payment,
only the actual area of structural glazing (including width of grooves ) on the
external face shall be measured in sqm. up to two decimal places.
Note:-2. The following performance test are to be conducted on structural
glazing system if area of structural glazing exceeds 2500 Sqm from the certified
laboratories accreditated by NABL(National Accreditation Board for Testing and
Calibration Laboratories), Department of Science & Technologies, India. Cost of
testing is payable separately. The NIT approving authority will decide the
necessity of testing on the basis of cost of the work, cost of the test and
importance of the work. Performance Testing of Structural glazing system Tests
to be conducted in the NBL Certified laboratories
1. Performance Laboratory Test for Air Leakage Test (-50pa to – 300pa) &
(+50pa to +300pa) as per ASTM E-283-04 testing method for a range of testing
limit 1 to 200 mVhr”
2. Static Water Penetration Test. (50pa to 1500pa) as per ASTME-331-09
testing method for a range up to 2000 ml.”
3. Dynamic Water Penetration (50pa to 1500pa) as per AAMA 501.01-05 testing
method for a range upto 2000 ml”
4. Structural Performance Deflection and deformation by static air pressure test
(1.5 times desing wind pressure without any failure) as per ASTME-330-10
testing method for a range upto 50 mm”
Page 9 of 66
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.NoDSR Code
No_ 2013Description
Total
Qty.Unit Rate Rate In Words DSR-Amount
5. Seismic Movement Test (upto 30 mm) as per AAMA 501.4-09 testing method
for Qualitative test” Tests to be conducted on site
6. Onsite Test for Water Leakage for a pressure range 50 kpa to 240 kpa (35psi)
upto 2000ml”
5.3 26.3
Providing, assembling and supplying vision glass panels (IGUs) comprising of
hermetically-sealed 6-12-6 mm insulated glass (double glazed) vision panel units
of size and shape as required and specified, comprising of an outer high
performance heat strengthened float glass 6mm thick, of approved colour and
shade with reflective soft coating on surface # 2 of approved colour and shade,
an inner Heat strengthned clear float glass 6mm thick, spacer tube 12mm wide,
dessicants, including primary seal and secondary seal (structural silicone
sealant) etc. all complete for the required performances, as per the Architectural
drawings, as per the approved shop drawings, as specified and as directed by
the Engineer-in-Charge. The IGUs shall be assembled in the factory/ workshop
of the glass processor. (Payment for fixing of IGU Panels in the curtain glazing is
included in cost of item No.1) For payment, only the actual area of glass on face
# 1 of the glass panels (excluding the areas of the grooves and weather silicone
sealant) provided and fixed in position, shall be measured in sqm.
1754 sqm 3948.95
Rupees Three Thousand
Nine Hundred Forty Eight
and Paise Ninety Five Only
6926616
(i) Coloured tinted float glass 6mm thick substrate with reflective soft coating on
face # 2, + 12mm Airgap + 6mm Heat Strengthened clear Glass of approved
make having properties as visible Light transmittance (VLT) of 25 to 35 %, Light
reflection internal 10 to 15%, light reflection external 10 to 20 %, shading
coefficient (0.25-0.28) and U value of 3.0 to 3.3 W/m2 degree K etc.
5.4 26.4
Extra for openable side / top hung vision glass panels (IGUs) including providing
and supplying at site all accessories and hardwares for the openable panels as
specified and of the approved make such as heavy duty stainless steel friction
hinges, min 4 -point cremone locking sets with stainless steel plates, handles,
buffers etc. including necessary stainless steel screws/ fasteners, nuts, bolts,
washers etc. all complete as per the Architectural drawings, as per the approved
shop drawings, as specified and as directed by the Engineerin-Charge.
526 sqm 3032.30
Rupees Three Thousand
Thirty Two and Paise
Thirty Only
1595633
5.5 26.7
Designing, fabricating, testing, installing and fixing in position Curtain Wall with
Aluminium Composite Panel Cladding, with open grooves for linear as well as
curvilinear portions of the building , for all heights and all levels etc. including:
a) Structural analysis & design and preparation of shop drawings for pressure
equalisation or rain screen principle as required, proper drainage of water to
make it watertight including checking of all the structural and functional design.
Page 10 of 66
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.NoDSR Code
No_ 2013Description
Total
Qty.Unit Rate Rate In Words DSR-Amount
b) Providing, fabricating and supplying and fixing panels of aluminium composite
panel cladding in pan shape in metalic colour of approved shades made out of
4mm thick aluminium composite panel material consisting of 3mm thick FR
grade mineral core sandwiched between two Aluminium sheets (each 0.5mm
thick). The aluminium composite panel cladding sheet shall be coil coated, with
Kynar 500 based PVDF / Lumiflon based fluoropolymer resin coating of
approved colour and shade on face # 1 and polymer (Service) coating on face #
2 as specified using stainless steel screws, nuts, bolts, washers, cleats, weather
silicone sealant, backer rods etc.
c) The fastening brackets of Aluminium alloy 6005 T5 / MS with Hot Dip
Galvanised with serrations and serrated washers to arrest the wind load
movement, fasteners, SS 316 Pins and anchor bolts of approved make in SS
316, Nylon separators to prevent bi-metallic contacts all complete required to
perform as per specification and drawing
The item includes cost of all material & labour component, the cost of all mock
ups at site, cost of all samples of the individual components for testing in an
approved laboratory, field tests on the assembled working curtain wall with
aluminium composite panel cladding, cleaning and protection of the curtain wall
with aluminium composite panel cladding till the handing over of the building for
occupation. Base frame work for ACP cladding is payable under the relevant
aluminium item.s The Contractor shall provide curtain wall with aluminium
composite panel cladding, having all the performance characteristics all
complete , as per the Architectural drawings, as per item description, as
specified, as per the approved shop drawings and as directed by the Engineer-in-
Charge. However, for the purpose of payment, only the actual area on the
external face of the curtain wall with Aluminum Composite Panel Cladding
(including width of groove) shall be measured in sqm. up to two decimal places.
1316 sqm 3696.65
Rupees Three Thousand
Six Hundred Ninety Six
and Paise Sixty Five Only
4863054
Page 11 of 66
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.NoDSR Code
No_ 2013Description
Total
Qty.Unit Rate Rate In Words DSR-Amount
6.0 MARBLE & GRANITE WORK
6.1 8.2
Providing and fixing 18mm thick gang saw cut mirror polished premoulded and
prepolished) machine cut for kitchen platforms, vanity counters, window sills ,
facias and similar locations of required size of approved shade, colour and
texture laid over 20mm thick base cement mortar 1:4 (1 cement : 4 coarse sand)
with joints treated with white cement, mixed with matching pigment, epoxy touch
ups, including rubbing, curing, moulding and polishing to edge to give high gloss
finish etc. complete at all levels.
8.2.2 Granite of any colour and shade
a) 8.2.2.1 Area of slab upto 0.50 sqm 450 sqm 3724.70
Rupees Three Thousand
Seven Hundred Twenty
Four and Paise Seventy
Only
1676115
b) 8.2.2.2 Area of Slab over 0.50sqm 550 sqm 3769.70
Rupees Three Thousand
Seven Hundred Sixty Nine
and Paise Seventy Only
2073335
6.2 8.3
Extra for providing edge moulding to 18mm thick marble stone counters,
Vanities etc. including machine polishing to edge to give high gloss finish etc.
complete as per design approved by Engineer-in-Charge.
8.3.2 Granite work. 250 metre 210.65Rupees Two Hundred Ten
and Paise Sixty Five Only 52663
6.3 8.4
Extra for fixing marble /granite stone over and above corresponding basic item,
in facia and drops of width upto 150 mm with epoxy resin based adhesive
including cleaning etc. complete.
250 metre 225.75
Rupees Two Hundred
Twenty Five and Paise
Seventy Five Only
56438
6.4 8.5
Extra for providing opening of required size & shape for wash basins/ kitchen
sink in kitchen platform, vanity counters and similar location in
marble/Granite/stone work including necessary holes for pillar taps etc. including
rubbing and polishing of cut edges etc. complete.
34 each 350.80
Rupees Three Hundred
Fifty and Paise Eighty
Only
11927
6.5 8.6Mirror polishing on marble work / Granite work/ stone work where ever required
to give high gloss finish complete.550 sqm 196.85
Rupees One Hundred
Ninety Six and Paise
Eighty Five Only
108268
Page 12 of 66
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.NoDSR Code
No_ 2013Description
Total
Qty.Unit Rate Rate In Words DSR-Amount
7.0 WOOD AND PVC WORK
7.1 9.1
Providing wood work in frames of doors, windows, clerestory windows and other
frames, wrought framed and fixed in position with hold fast lugs or with dash
fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid
for separately).
7.1.1 9.1.1 Second class teak wood 3.86 cum 90495.80
Rupees Ninety Thousand
Four Hundred Ninety Five
and Paise Eighty Only
349404
7.2 2.35Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-
termite treatment (excluding the cost of chemical emulsion) :
7.2.1 2.35.5
Treatment at points of contact of wood work by chemical emulsion
Chlorpyriphos/ Lindane (in oil or kerosene based solution) @ 0.5 litres per hole
by drilling 6mm dia holes at downward angle of 45 degree at 150 mm centre to
centre and sealing the same.
360 metre 187.65
Rupees One Hundred
Eighty Seven and Paise
Sixty Five Only
67554
7.3 9.21
Providing and fixing ISI marked flush door shutters conforming to IS: 2202 (Part
I) non-decorative type, core of block board construction with frame of 1st class
hard wood and well matched commercial 3 ply veneering with vertical grains or
cross bands and face veneers on both faces of shutters :
7.3.1 9.21.135 mm thick including ISI marked Stainless Steel butt hinges with necessary
screws. 129 sqm 1684.75
Rupees One Thousand Six
Hundred Eighty Four and
Paise Seventy Five Only
217333
7.4 9.23
Extra for providing lipping with 2nd class teak wood battens 25 mm minimum
depth on all edges of shutters (over all area of door shutter to be measured) over
item no. 9.20 and 9.21
129 sqm 348.45
Rupees Three Hundred
Forty Eight and Paise
Forty Five Only
44950
7.5 9.24Extra for providing vision panel not exceeding 0.1 sqm in all type of flush doors
(cost of glass excluded) (overall area of door shutter to be measured) :
7.5.1 9.24.1 Rectangular or square. 129 sqm 133.55
Rupees One Hundred
Thirty Three and Paise
Fifty Five Only
17228
9.24.2 Circular 0 sqm 209.05Rupees Two Hundred
Nine and Paise Five Only 0
7.6 9.40Providing and fixing wooden moulded beading to door and window frames with
iron screws, plugs and priming coat on unexposed surface etc. complete :
9.40.1 2nd class teak wood
7.6.1 9.40.1.2 50 x 20 mm 360 metre 148.10
Rupees One Hundred
Forty Eight and Paise Ten
Only
53316
Supplying and fixing Supplying and fixing
Page 13 of 66
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.NoDSR Code
No_ 2013Description
Total
Qty.Unit Rate Rate In Words DSR-Amount
7.7 9.127
Providing & Fixing decorative high pressure laminated sheet of plain / wood
grain in gloss / matt / suede finish with high density protective surface layer and
reverse side of adhesive bonding quality conforming to IS : 2046 Type S
including cost of adhesive of approved quality
7.7.1 9.127.2 1.0 mm thick. 258 sqm 663.20
Rupees Six Hundred Sixty
Three and Paise Twenty
Only
171106
Providing and fixing hardware's for Door :
7.8 9.100
Providing and fixing aluminum handles ISI marked anodised (anodic coating not
less than grade AC 10 as per IS:1868) transparent or dyed to required colour or
shade or powder coated( minimum thickness 50 micron aluminum)with
necessary screws etc. complete :
a ) 9.100.1 125 mm 86 each 66.95Rupees Sixty Six and
Paise Ninety Five Only 5758
b ) 9.100.2 100 mm 6 each 52.80Rupees Fifty Two and
Paise Eighty Only 317
7.9 9.97
Providing and fixing aluminum tower bolts ISI marked anodised (anodic coating
not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required
colour or shade or powder coated (minimum thickness 50 micron aluminum)with
necessary screws etc. complete :
a ) 9.97.2 250x10 mm 92 each 90.65Rupees Ninety and Paise
Sixty Five Only 8340
b ) 9.97.3 200x10 mm 43 each 76.40Rupees Seventy Six and
Paise Forty Only 3285
c ) 9.97.4 150x10mm 6 each 62.75Rupees Sixty Two and
Paise Seventy Five Only 377
7.10 9.101
Providing and fixing aluminum hanging floor door stopper ISI marked anodised
(anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed
to required colour and shade or powder coated (minimum thickness 50 micron
aluminum) with necessary screws etc. complete.
9.101.1 Single rubber stopper 46 each 33.75Rupees Thirty Three and
Paise Seventy Five Only 1553
7.11 9.96
Providing and fixing aluminum sliding door bolts ISI marked anodised (anodic
coating not less than grade AC 10 as per IS : 1868) transparent or dyed to
required colour or shade or powder coated( minimum thickness 50 micron
aluminum) with nuts and screws etc. complete :
a ) 9.96.1 300x16 mm 43 each 215.30
Rupees Two Hundred
Fifteen and Paise Thirty
Only
9258
Page 14 of 66
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.NoDSR Code
No_ 2013Description
Total
Qty.Unit Rate Rate In Words DSR-Amount
b ) 9.96.2 250x16mm 3 each 180.45
Rupees One Hundred
Eighty and Paise Forty
Five Only
541
7.12 9.84
Providing and fixing aluminum die cast body tubular type universal hydraulic door
closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight
upto 35 kg and door width upto 700 mm) with necessary accessories and screws
etc. complete.
27 each 1027.20
Rupees One Thousand
Twenty Seven and Paise
Twenty Only
27734
7.13 9.102
Providing and fixing Aluminum Casement stays, ISI marked anodised (anodic
coating not less than grade AC 10 as per IS : 1868) transparent or dyed to
required colour or shade or powder coated ( minimum thickness 50 micron
aluminum)with nuts and screws etc. complete :
70 each 68.40Rupees Sixty Eight and
Paise Forty Only 4788
7.14 9.76
Providing and fixing bright finished brass 100 mm mortice latch and lock with 6
levers and a pair of lever handles with necessary screws etc. Complete (best
make of approved quality).
27 each 514.55
Rupees Five Hundred
Fourteen and Paise Fifty
Five Only
13893
7.15 21.18
Providing and fixing 12 mm thick frameless toughened glass door shutter of
approved brand and manufacturer, including providing and fixing top & bottom
pivot & spring type fixing arrangement and making necessary holes etc. for fixing
required door fittings, all complete as per direction of Engineer-in-charge (Door
handle, lock and stopper etc.to be paid separately).
331 sqm 4692.70
Rupees Four Thousand
Six Hundred Ninety Two
and Paise Seventy Only
1554222
Page 15 of 66
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.NoDSR Code
No_ 2013Description
Total
Qty.Unit Rate Rate In Words DSR-Amount
7.17Providing and fixing approved brand and manufacturer SS 304 grade
hardware's for Doors etc.
7.18 9.136
Providing and fixing fire resistant door frame of section 143 x 57 mm having built
in rebate made out of 16 SWG G.I. sheet (zinc coating not less than 120
gm/sqm) duly filled with vermuculite based concrete mix, suitable for mounting
60 minutes fire rated door shutters. The frame is fitted with intumuscent fire seal
strip of size 10x4 mm (minimum) alround the frame and fixing with dash fastener
of approved size and make, including applying a coat of approved brand fire
resistant primer etc. complete as per direction of Engineer-in-charge (Dash
fastener to be paid for separately).
200 metre 1190.65
Rupees One Thousand
One Hundred Ninety and
Paise Sixty Five Only
237654
7.19 9.137
Providing and fixing 50 mm thick glazed fire resistant door shutters of 60 minutes
fire rating conforming to IS:3614 (Part-II), tested and certified as per laboratory
approved by Engineer-in-charge, with suitable mounting on door frame,
consisting of vertical styles, lock rail, top rail 100 mm wide, bottom rail 200 mm
wide, made out of 16 SWG G.I.sheet (zinc coating not less than 120 gm/m2)
duly filled FR insulation material and fixing with necessary stainless steel ball
bearing hinges of approved make, including applying a coat of approved fire
resistant primer etc. all complete as per direction of Engineer-in-charge
(panneling to be paid for separately).
110 sqm 6205.05
Rupees Six Thousand Two
Hundred Five and Paise
Five Only
685038
7.20 9.138
Providing and fixing glazing in fire resistant door shutters, fixed panels,
ventilators and partitions etc., with G.I. beading of appropriate size, made out of
20 SWG G.I.sheet (zinc coating not less than 120 gm/m2), fire resistant sealant,
including applying a coat of approved fire resistant primer on G.I. beading etc.,
complete all as per direction of Engineer-in-charge.
9.138.1With clear fire resistant glass panes 6mm thick of approved brand, having
minimum 60 minutes fire resistance110 sqm 26954.60
Rupees Twenty Six
Thousand Nine Hundred
Fifty Four and Paise Sixty
Only
2975788
7.21 9.139
Providing and fixing panic bar / latch (Double point) fitted with a single body, Trim
Latch & Lock on back side of the Panic Latch of reputed brand and manufacture
to be approved by the Engineer- in- charge, all complete.
32 nos 5892.30
Rupees Five Thousand
Eight Hundred Ninety Two
and Paise Thirty Only
188554
Page 16 of 66
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.NoDSR Code
No_ 2013Description
Total
Qty.Unit Rate Rate In Words DSR-Amount
7.22 9.105
Providing and fixing partition upto ceiling height consisting of G.I. frame and
required board, including providing and fixing of frame work made of special
section power pressed/ roll form G.I. sheet with zinc coating of 120
gms/sqm(both side inclusive), consisting of floor and ceiling channel 50mm wide
having equal flanges of 32 mm and 0.50 mm thick, fixed to the floor and ceiling
at the spacing of 610 mm centre to centre with dash fastener of 12.5 mm dia
meter 50 mm length or suitable anchor fastener or metal screws with nylon plugs
and the studs 48 mm wide having one flange of 34 mm and other flange 36 mm
and 0.50 mm thick fixed vertically within flanges of floor and ceiling channel and
placed at a spacing of 610 mm centre to centre by 6 mm dia bolts and nuts,
including fixing of studs along both ends of partition fixed flush to wall with
suitable anchor fastener or metal screws with nylon plugs at spacing of 450 mm
centre to centre, and fixing of boards to both side of frame
work by 25 mm long dry wall screws on studs, floor and ceiling channels at the
spacing of 300 mm centre to centre. The boards are to be fixed to the frame
work with joints staggered to avoid through cracks, M.S. fixing channel of 99 mm
width (0.9 mm thick having two flanges of 9.5 mm each) to be provided at the
horizontal joints of two boards, fixed to the studs using metal to metal flat head
screws, including jointing and finishing to a flush finish with recommended
jointing compound, jointing tape, angle beads at corners (25 mm x 25 mm x 0.5
mm), joint finisher and two coats of primer suitable for board as per
manufacture's specification and direction of engineer in charge all complete.
7.22.1 9.105.175 mm overall thickness partition with 12.5 mm thick double skin fire rated board
conforming to IS: 2095: part I660 sqm 1253.35
Rupees One Thousand
Two Hundred Fifty Three
and Paise Thirty Five Only
827211
8.0 STEEL WORK
8.1 10.1
Structural steel work in single section, fixed with or without connecting plate,
including cutting, hoisting, fixing in position and applying a priming coat of
approved steel primer all complete.
10000 kg 66.85Rupees Sixty Six and
Paise Eighty Five Only 668500
8.2 10.2
Structural steel work riveted, bolted or welded in built up sections, trusses and
framed work, including cutting, hoisting, fixing in position and applying a priming
coat of approved steel primer all complete:20000 kg 73.65
Rupees Seventy Three
and Paise Sixty Five Only 1473000
Page 17 of 66
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.NoDSR Code
No_ 2013Description
Total
Qty.Unit Rate Rate In Words DSR-Amount
8.3 7.41
Providing and fixing structural steel frame (for dry cladding/ACP/ZINC Cromate
panels with 30 mm thick gang saw cut with machine cut edges sand stone) on
walls at all heights using M.S. square/ rectangular tube in the required pattern as
per architectural drawing, including cost of cutting, bending, welding etc. The
frame work shall be fixed to the wall with the help of M.S. brackets/ lugs of angle
iron/ flats etc. which shall be welded to the frame and embedded in brick wall
with cement concrete block 1:2:4 (1 cement :2 coarse sand :4 graded stone
aggregate 20 mm nominal size) of size 300x230x300 mm, including cost of
necessary centring and shuttering and with approved expansion hold fasteners
on CC/RCC surface, including drilling necessary holes. Approved cramps/ pins
etc. shall be welded to the frame work to support stone cladding, the steel work
will be given a priming coat of Zinc primer as approved by Engineerin-charge
and painted with two or more coats of epoxy paint (Shop drawings shall be
submitted by the contractor to the Engineer-in-charge for approval before
execution). The frame work shall be fixed in true horizontal & vertical
lines/planes. (Only structural steel frame work shall be measured for the purpose
of payment, stainless steel cramps shall be paid for separately and nothing extra
shall be paid).
19733 kg 134.50
Rupees One Hundred
Thirty Four and Paise Fifty
Only
2654082
8.4 10.25
Steel work welded in built up sections/ framed work, including cutting, hoisting,
fixing in position and applying a priming coat of approved steel primer using
structural steel etc. as required.
8.4.1 10.25.2 In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works 8500 kg 86.50Rupees Eighty Six and
Paise Fifty Only 735250
8.5 10.28
Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes,
channels, plates etc., including welding, grinding, buffing, polishing and making
curvature (wherever required) and fitting the same with necessary stainless steel
nuts and bolts complete, i/c fixing the railing with necessary accessories &
stainless steel dash fasteners , stainless steel bolts etc., of required size, on the
top of the floor or the side of waist slab with suitable arrangement as per
approval of Engineer-in-charge, ( for payment purpose only weight of stainless
steel members shall be considered excluding fixing accessories such as nuts,
bolts, fasteners etc.).
5124 kg 611.10
Rupees Six Hundred
Eleven and Paise Ten
Only
3131276
8.7 10.6
Supplying and fixing rolling shutters of approved make, made of required size
M.S. laths, interlocked together through their entire length andjointed together at
the end by end locks, mounted on specially designedpipe shaft with brackets,
side guides and arrangements for inside and outside locking with push and pull
operation complete, including thecost of providing and fixing necessary 27.5 cm
long wire springs manufactured from high tensile steel wire of adequate strength
conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for
rolling shutters.
Page 18 of 66
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.NoDSR Code
No_ 2013Description
Total
Qty.Unit Rate Rate In Words DSR-Amount
8.7.1 10.6.1 80x1.25 mm M.S. laths with 1.25 mm thick top cover 28.80 sqm 2044.15
Rupees Two Thousand
Forty Four and Paise
Fifteen Only
58872
8.8 10.7 Providing and fixing ball bearing for rolling shutters. 8.00 each 436.45
Rupees Four Hundred
Thirty Six and Paise Forty
Five Only
3492
8.9 10.8Extra for providing mechanical device chain and crank operation for
operating rolling shutters.
8.9.1 10.8.1 Exceeding 10.00 sqm and upto 16.80 sqm in the area. 28.80 sqm 665.50Rupees Six Hundred Sixty
Five and Paise Fifty Only 19166
8.10 10.9
Extra for providing grilled rolling shutters manufactured out of 8 mm dia.M.S. bar
instead of laths as per design approved by Engineer-in-charge.(area of grill to be
measured).
12.00 sqm 313.60
Rupees Three Hundred
Thirteen and Paise Sixty
Only
3763
9.0 FLOORING
9.1 11.3
Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone
aggregate) finished with a floating coat of neat cement including cement slurry,
but excluding the cost of nosing of steps etc. complete.
9.1.1 11.3.1 40mm thick with 20mm nominal size stone aggregate. 60 sqm 316.80
Rupees Three Hundred
Sixteen and Paise Eighty
Only
19008
9.2 11.6Cement plaster skirting (up to 30 cm height) with cement mortar 1:3 (1 cement :
3 coarse sand) finished with a floating coat of neat cement.
9.2.1 11.6.1 18 mm thick. 6 sqm 299.20
Rupees Two Hundred
Ninety Nine and Paise
Twenty Only
1795
9.3 11.20
Chequerred precast cement concrete tiles 22 mm thick in footpath & courtyard,
jointed with neat cement slurry mixed with pigment to match the shade of tiles,
including rubbing and cleaning etc. complete, on 20 mm thick bed of cement
mortar 1:4 (1 cement: 4 coarse sand).
9.3.1 11.20.4 Ordinary cement without any pigment 994 sqm 608.25
Rupees Six Hundred Eight
and Paise Twenty Five
Only
604686
9.4 11.26
Kota stone slab flooring over 20 mm (average) thick base laid over and jointed
with grey cement slurry mixed with pigment to match the shade of the slab,
including rubbing and polishing complete with base of cement mortar 1 : 4 (1
cement : 4 coarse sand) :
Page 19 of 66
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.NoDSR Code
No_ 2013Description
Total
Qty.Unit Rate Rate In Words DSR-Amount
9.4.1 11.26.1 25mm thick 546 sqm 1071.70
Rupees One Thousand
Seventy One and Paise
Seventy Only
585405
9.5 11.27
Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on
12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed
with grey cement slurry mixed with pigment to match the shade of the slabs,
including rubbing and polishing complete.
55 sqm 1100.85
Rupees One Thousand
One Hundred and Paise
Eighty Five Only
60133
9.6 11.36
Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622
(thickness to be specified by the manufacturer), of approved make, in all colours,
shades except burgundy, bottle green, black of any size as approved by
Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed
of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement
slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of
matching shade complete.
1106 sqm 793.60
Rupees Seven Hundred
Ninety Three and Paise
Sixty Only
877505
9.7 11.41
Providing and laying vitrified floor tiles in different sizes (thickness to be specified
by the manufacturer) with water absorption less than 0.08% and conforming to IS
: 15622, of approved make, in all colours and shades, laid on 20mm thick
cement mortar 1:4 (1 cement : 4 coarse sand), including grouting the joints with
white cement and matching pigments etc., complete.
a) 11.41.2 Size of Tile 600x600 mm 458 sqm 1402.55
Rupees One Thousand
Four Hundred Two and
Paise Fifty Five Only
642734
b) 11.41.3 Size of Tile 800x800 mm 238 sqm 1644.55
Rupees One Thousand Six
Hundred Forty Four and
Paise Fifty Five Only
390627
9.8 11.46
Providing and laying Vitrified tiles in different sizes (thickness to be specified by
manufacturer), with water absorption less than 0.08 % and conforming to I.S.
15622, of approved make, in all colours & shade, in skirting, riser of steps, over
12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), including
grouting the joint with white cement & matching pigments etc. complete.
a) 11.46.2 Size of Tile 600x600 mm 551 sqm 1411.45
Rupees One Thousand
Four Hundred Eleven and
Paise Forty Five Only
777463
b) 11.46.3 Size of Tile 800x800 mm 24 sqm 1655.50
Rupees One Thousand Six
Hundred Fifty Five and
Paise Fifty Only
39323
Page 20 of 66
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.NoDSR Code
No_ 2013Description
Total
Qty.Unit Rate Rate In Words DSR-Amount
9.9 16.89
Providing and laying matt finished vitrified tile of size 300x300x9.8mm having
with water absorption less than 0.5% and conforming to IS: 15622 of approved
make in all colours and shades in for outdoor floors such as footpath, court yard,
multi modals location etc., laid on 20mm thick base of cement mortar 1:4
(1cement : 4 coarse sand) in all shapes & patterns including grouting the joints
with white cement mixed with matching pigments etc. complete as per direction
of Engineer-in-Charge.
157 sqm 947.25
Rupees Nine Hundred
Forty Seven and Paise
Twenty Five Only
148434
9.14 8.12
Providing and laying flamed finish Granite stone flooring in required design and
patterns, in linear as well as curvilinear portions of the building all complete as
per the architectural drawings with 18 mm thick stone slab over 20 mm
(average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and
jointed with cement slurry and pointing with white cement slurry admixed with
pigment of matching shade including rubbing , curing and polishing etc. all
complete as specified and as directed by the Engineer-in-Charge :
9.14.1
a) Flamed finish granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye
or equivalent. 13 sqm 2782.15
Rupees Two Thousand
Seven Hundred Eighty
Two and Paise Fifteen
Only
35130
10.0 ROOFING
10.1 12.22
Making khurras 45x45 cm with average minimum thickness of 5 cm cement
concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm
nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm
cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement,
rounding the edges and making and finishing the outlet complete.
38 each 167.45
Rupees One Hundred
Sixty Seven and Paise
Forty Five Only
6397
10.2 12.21
Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4
stone aggregate 10 mm and down gauge), including finishing with cement mortar
1:3 (1 cement : 3 fine sand) as per standard design :
10.2.1 12.21.1 In 75 x75 mm deep chase 141 Rmt 127.95
Rupees One Hundred
Twenty Seven and Paise
Ninety Five Only
18041
10.3 12.55
Providing and fixing Heat Resistant Terrace Tiles (300 mm x 300 mm x 20 mm)
with SRI (solar refractive index) > 78, solar reflection >0.70 and initial emittance
>0.75 on waterproof and sloped surface of terrace, laid on 20 mm thick cement
sand mortar in the ratio of 1:4 (1 cement : 4 coarse sand) and grouting the joints
with mix of white cement & marble powder in ratio of 1:1, including rubbing and
polishing of the surface upto 3 cuts complete, including providing skirting upto
150 mm height along the parapet walls in the same manner
764 Sqm 1108.70
Rupees One Thousand
One Hundred Eight and
Paise Seventy Only
847047
Page 21 of 66
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.NoDSR Code
No_ 2013Description
Total
Qty.Unit Rate Rate In Words DSR-Amount
10.4 12.34
Providing fixing thermal insulation of ceiling (under deck insulation) with Resin
Bonded Fibre glass wool conforming to IS : 8183, density 24kg / m3, 50mm
thick, wrapped in 200 G Virgin Polythene bags, fixed to ceiling with metallic
cleats (50x50x3 mm) @ 60 cm and wire mesh of 12.5 mm x 24 gauge wire
mesh, for top most ceiling of building.
764 Sqm 465.10
Rupees Four Hundred
Sixty Five and Paise Ten
Only
355336
10.5 12.45
Providing and fixing at all height false ceiling including providing and fixing of
frame work made of special sections power pressed from M.S. sheet and
galvanised in accordance with zinc coating of grade 350 as per IS : 277 and
consisting of angle cleats of size 25mm wide x 1.6mm thick with flanges of
22mm and 37mm at 1200mm centre to centre one flange fixed to the ceiling with
dash fastener 12.5mm diax40mm long with 6mm dia bolts to the angle hangers
of 25x25x0.55mm of required length, and other end of angle hanger being fixed
with nut and bolts to G.I. channels 45x15x0.9mm running at the rate of 1200mm
centre to centre to which the ceiling section 0.5mm thick button wedge of 80mm
with tapered flanges of 26mm each having clips of 10.5mm at 450mm centre to
centre shall be fixed in a direction perpendicular to G.I. channel with connecting
clips made out of 2.64mm diax230mm long G.I. wire at every junction including
fixing the gypsum board with ceiling section and perimeter channels 0.5mm thick
27mm high having flanges of 20mm and 30mm long, the perimeter of ceiling
fixed to wall/partition with the help of rawl plugs at 450mm centre to centre with
25mm long drive-all screws @ 230mm interval including jointing and fixing to a
flush finish of tapered and square edges of the board with recommended filler,
jointing tapes, finisher and two coats of primer suitable for board as per
manufactures specification and also including the cost of making openings for
light fittings, grills, diffusers, cutouts made with frame of perimeter channels
suitably fixed all complete as per drawing and specification and direction of the
Engineer in Charge but excluding the cost of painting with :
10.5.1 12.45.1 12.5 mm thick tapered edge gypsum board conforming to IS: 2095- Part I. 1853 sqm 804.80
Rupees Eight Hundred
Four and Paise Eighty
Only
1491275
Page 22 of 66
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.NoDSR Code
No_ 2013Description
Total
Qty.Unit Rate Rate In Words DSR-Amount
10.6 12.52.2
Providing and fixing tiled false ceiling of approved materials of size 595x595 mm
in true horizontal level suspended on inter locking metal grid of hot dipped
galvanized steel sections ( galvanized @ 120 gsm/sqm, both side inclusive)
consisting of main "T" runner with suitably spaced joints to get required length
and of size 24x38mm made from 0.30mm thick (minimum) sheet, spaced at
1200mm center to center and cross "T" of size 24x25mm made of 0.30mm thick
(minimum) sheet, 1200mm long spaced between main "T" at 600mm center to
center to form a grid of 1200x600 mm and secondary cross "T" of length 600mm
and size 24x25mm made of 0.30 mm thick (minimum) sheet to be interlocked at
middle of the 1200x600mm panel to form grids of 600x600mm and wall angle of
size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid
including, wherever, required, cutting/making, opening for services like diffusers,
grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be
suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 x mm
fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4mm GI
adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm
spaced at 1200mm center to center along main T, bottom exposed width of 24
mm of all T-sections shall be pre-painted with polyester paint, all complete at all
heights as per specifications drawings and as directed by Engineer-in-charge.
GI Metal Ceiling Lay in perforated Tegular edge global white color tiles of size
595x595 mm and 0.5 mm thick with 8 mm drop; made of GI sheet having
galvanizing of 100 gms/sqm (both sides inclusive) and 20% perforation area with
1.8 mm dia holes and having NRC (Noise Reduction Coefficient ) of 0.5, electro
statically polyester powder coated of thickness 60 microns (minimum), including
factory painted after bending and perforation, and backed with a black Glass
fiber acoustical fleece.
4172 sqm 1637.15
Rupees One Thousand Six
Hundred Thirty Seven and
Paise Fifteen Only
6830110
11.0 FINISHING WORK
11.1 13.1 12mm cement plaster of mix :
11.1.1 13.1.2 1:6 (1 cement : 6 fine sand) 1158 sqm 133.85
Rupees One Hundred
Thirty Three and Paise
Eighty Five Only
154946
11.2 13.11
18 mm cement plaster in two coats under layer 12 mm thick cement plaster 1:5
(1 cement : 5 coarse sand) finished with a top layer 6 mm thick cement plaster
1:6 (1 cement : 6 fine sand).
1158 sqm 215.40
Rupees Two Hundred
Fifteen and Paise Forty
Only
249349
11.3 13.2 15 mm cement plaster on the rough side of single or half brick wall of mix :
11.3.1 13.2.2 1:6 (1 cement : 6 fine sand) 1158 sqm 154.70
Rupees One Hundred Fifty
Four and Paise Seventy
Only
179082
11.4 13.7 12 mm cement plaster finished with a floating coat of neat cement of mix :Page 23 of 66
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.NoDSR Code
No_ 2013Description
Total
Qty.Unit Rate Rate In Words DSR-Amount
11.4.1 13.7.2 1:4 (1 cement: 4 fine sand) 525 sqm 180.60
Rupees One Hundred
Eighty and Paise Sixty
Only
94815
11.5 13.16.1 6 mm cement plaster of mix : 1:3 (1 cement : 3 fine sand) 15159 sqm 120.35
Rupees One Hundred
Twenty and Paise Thirty
Five Only
1824378
11.6 13.26Providing and Applying plaster of Paris putty of 2mm thickness over Plastered
surface to prepare the surface even and smooth complete16317 sqm 100.95
Rupees One Hundred and
Paise Ninety Five Only 1647156
11.7 13.37 White washing with lime to give an even shade:
11.7.1 13.37.1 New work (three or more coats) 719 sqm 14.35Rupees Fourteen and
Paise Thirty Five Only 10319
11.8 13.39 Colour washing such as green, blue or buff to give an even shade
11.8.1 13.39.1 New work (two or more coats) with a base coat of white washing with lime 719 sqm 19.75Rupees Nineteen and
Paise Seventy Five Only 14202
11.9 13.52
Finishing with Epoxy paint (two or more coats) at all locations prepared and
applied as per manufacturer's specifications including appropriate priming coat,
preparation of surface, etc. complete.
a) 13.52.1 On steel work 3000 sqm 109.80
Rupees One Hundred
Nine and Paise Eighty
Only
329400
11.10 13.45 Finishing walls with textured exterior paint of required shade :
13.45.1New work (Two or more coats applied @ 3.28 ltr/10 sqm) over
and including priming coat of exterior primer applied @ 2.20kg/10 sqm.719 sqm 127.10
Rupees One Hundred
Twenty Seven and Paise
Ten Only
91398
11.11 13.50 Applying Prime Coat:
11.11.1 13.50.1With ready mixed pink or grey primer of approved brand and manufacture on
wood work ( hard and soft wood)166 sqm 30.75
Rupees Thirty and Paise
Seventy Five Only 5092
11.12 14.61Painting (one or more coats) with black Japan paint of approved brand and
manufacture to give an even shade.59 sqm 38.50
Rupees Thirty Eight and
Paise Fifty Only 2287
11.13 13.81
Distempering with 1st quality acrylic distemper, having VOC (Volatile Organic
Compound ) content less than 50 grams/ litre, of approved brand and
manufacture, including applying additional coats wherever required, to achieve
even shade and colour.
11.13.1 13.81.2 Two coats 719 sqm 41.75Rupees Forty One and
Paise Seventy Five Only 30022
Page 24 of 66
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.NoDSR Code
No_ 2013Description
Total
Qty.Unit Rate Rate In Words DSR-Amount
11.14 13.83
Wall painting with premium acrylic emulsion paint of interior grade, having VOC
(Volatile Organic Compound ) content less than 50 grams/ litre. Of Approved
brand and manufacture, including applying additional coats wherever required to
achieve even shade and colour.
11.14.1 13.83.2 Two coats. 439 sqm 70.75Rupees Seventy and
Paise Seventy Five Only 31025
11.15 13.84
Painting with synthetic enamel paint, having VOC (Volatile Organic Compound)
content less than 150 grams/ litre, of approved brand and manufacture, including
applying additional coats wherever required to achieve even shade and colour.
11.15.1 13.84.2 Two coats. 908 sqm 67.00Rupees Sixty Seven and
Paise Zero Only 60809
12.0 ALUMINIUM WORK
12.1 21.1
Providing and fixing aluminum work for doors, windows, ventilators and
partitions with extruded built up standard tubular sections/ appropriate Z
sections and other sections of approved make conforming to IS: 733 and IS :
1285, fixed with rawl plugs and screws or with fixing clips, or with expansion
hold fasteners including necessary filling up of gaps at junctions, at top, bottom
and sides with required PVC/neoprene felt etc. Aluminum sections shall be
smooth, rust free, straight, mitred and jointed mechanically wherever required
including cleat angle, Aluminum snap beading for glazing / paneling, C.P. brass /
stainless steel screws, all complete as per architectural drawings and the
directions of Engineer-in-charge. (Glazing and paneling to be paid for
separately) :
112.1 21.1.1 For fixed portion
12.1.1 21.1.1.2 Powder coated aluminum (minimum thickness of powder coating 50 micron) 3537 kg 373.00
Rupees Three Hundred
Seventy Three and Paise
Zero Only
1319301
12.2 21.1.2
For shutters of doors, windows & ventilators including providing and fixing
hinges/ pivots and making provision for fixing of fittings wherever required
including the cost of PVC / neoprene gasket required (Fittings shall be paid for
separately).
12.2.1 21.1.2.2 Powder coated aluminum (minimum thickness of powder coating 50 micron) 707 kg 427.60
Rupees Four Hundred
Twenty Seven and Paise
Sixty Only
302484
12.3 21.3
Providing and fixing glazing in aluminum door, windows, ventilator shutters and
partitions etc. with PVC/ neoprene gasket etc. complete as per the architectural
drawings and the directions of the Engineer-in-Charge. (Cost of aluminum snap
beading shall be paid in basic item).
a) 21.3.1 With float glass panes of 4.0mm thickness 100 sqm 790.00
Rupees Seven Hundred
Ninety and Paise Zero
Only
79000
Page 25 of 66
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.NoDSR Code
No_ 2013Description
Total
Qty.Unit Rate Rate In Words DSR-Amount
b) 21.3.2 With float glass panes of 5.50 mm thickness 50 sqm 1009.00Rupees One Thousand
Nine and Paise Zero Only 50450
12.5 21.8
Filling the gap in between aluminum frame & adjacent RCC/ Brick/ Stone work
by providing weather silicon sealant over backer rod of approved quality as per
architectural drawings and direction of Engineer-in-charge complete.
786 metre 83.05Rupees Eighty Three and
Paise Five Only 65277
12.6 21.14
Providing and fixing anodised aluminum (anodised transparent or dyed to
required shade according to IS: 1868. Minimum anodic coating of grade AC 15)
sub frame work for windows and ventilators with extruded built up standard
tubular sections of approved make conforming to IS: 733 and IS: 1285, fixed with
dash fastener of required dia and size (Dash fastener to be paid for separately).
354 kg 310.85
Rupees Three Hundred
Ten and Paise Eighty Five
Only
109948
Page 26 of 66
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.NoDSR Code
No_ 2013Description
Total
Qty.Unit Rate Rate In Words DSR-Amount
13.0 WATER PROOFING WORK
13.1 22.1
Providing and laying integral cement based treatment for waterproofing on
horizontal surface at all depth below ground level for under ground structures as
directed by Engineer-in-Charge and consisting of : i) Ist layer of 22 mm to 25 mm
thick approved and specified rough stone slab over a 25 mm thick base of
cement mortar 1:3 (1 cement : 3 coarse sand) mixed with water proofing
compound conforming to IS:2645 in the recommended proportion over the
leveling course (leveling course to be paid separately). Joints sealed and
grouted with cement slurry mixed with water proofing compound. ii) 2nd layer of
25 mm thick cement mortar 1:3 (1 cement:3 coarse sand) mixed with water
proofing compound in recommended proportions. iii) Finishing top with stone
aggregate of 10 mm to 12mm nominal size spreading @ 8 cudm/sqm thoroughly
embedded in the 2nd layer.
13.1.1 22.1.1 Using rough kota stone. 150 sqm 844.10
Rupees Eight Hundred
Forty Four and Paise Ten
Only
126615
13.2 22.2
Providing and laying integral cement based treatment for waterproofing on the
vertical surface by fixing specified stone slab 22 mm to 25 mm thick with cement
slurry mixed with water proofing compound conforming to IS:2645 in
recommended proportions with gap of 20 mm (minimum) between stone slabs
and the receiving surfaces and filling the gaps with neat cement slurry mixed with
water proofing compound and finishing the exterior of stone slab with cement
mortar 1:3 (1 cement : 3 coarse sand) 20 mm thick with neat cement punning
mixed with water proofing compound in recommended proportion complete at all
levels and as directed by Engineer-in-charge :
13.2.1 22.2.1 Using rough kota stone. 700 sqm 1036.90
Rupees One Thousand
Thirty Six and Paise Ninety
Only
725830
13.3 22.5
Providing and laying water proofing treatment in sunken portion of WCs,
bathroom etc., by applying cement slurry mixed with water proofing cement
compound consisting of applying : a) First layer of slurry of cement @ 0.488
kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm. This layer
will be allowed to air cure for 4 hours. b) Second layer of slurry of cement @
0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm.
This layer will be allowed to air cure for 4 hours followed with water curing for 48
hours. The rate includes preparation of surface, treatment and sealing of all
joints, corners, junctions of pipes and masonry with polymer mixed slurry.
429 sqm 255.00Rupees Two Hundred Fifty
Five and Paise Zero Only 109497
Page 27 of 66
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.NoDSR Code
No_ 2013Description
Total
Qty.Unit Rate Rate In Words DSR-Amount
13.4 22.7
Providing and laying integral cement based water proofing treatment including
preparation of surface as required for treatment of roofs, balconies, terraces etc
consisting of following operations: a) Applying a slurry coat of neat cement using
2.75 kg/sqm of cement admixed with water proofing compound conforming to IS.
2645 and approved by Engineer-in-charge over the RCC slab including adjoining
walls upto 300 mm height including cleaning the surface before treatment. b)
Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm
size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with
water proofing compound conforming to IS : 2645 and approved by Engineer-in-
charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse
sand ) admixed with water proofing compound conforming to IS : 2645 and
approved by Engineer-in-charge to required slope and treating similarly the
adjoining walls upto 300 mm height including rounding of junctions of walls and
slabs c) After two days of proper curing applying a second coat of cement slurry
using 2.75 kg/ sqm of cement admixed with water proofing compound
conforming to IS : 2645 and approved by Engineer-in-charge. d) Finishing the
surface with 20 mm thick joint less cement mortar of mix 1:4 (1 cement :4 coarse
sand) admixed with water proofing compound conforming to IS : 2645 and
approved by Engineer-in-charge including laying glass fibre cloth of approved
quality in top layer of plaster and finally finishing the surface with trowel with neat
cement slurry and making pattern of 300x300mm square 3 mm deep. e) The
whole terrace so finished shall be flooded with water for a minimum period of two
weeks for curing and for final test. All above operations to be done in order and
as directed and specified by the Engineer-in-Charge :
13.4.1 22.7.1 With average thickness of 120 mm and minimum thickness at khurra as 65 mm. 764 sqm 882.60
Rupees Eight Hundred
Eighty Two and Paise
Sixty Only
674306
13.5 22.14 Grading roof for water proofing treatment with
13.5.1 22.14.1Cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20
mm nominal size) 38 cum 5021.05
Rupees Five Thousand
Twenty One and Paise
Five Only
191804
14.0 MISCELLANEOUS WORK
Page 28 of 66
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.NoDSR Code
No_ 2013Description
Total
Qty.Unit Rate Rate In Words DSR-Amount
14.2 20.2
Boring, providing and installing bored cast-in-situ reinforced cement concrete
piles of grade M-25 of specified diameter and length below the pile cap, to carry
a safe working load not less than specified, excluding the cost of steel
reinforcement but including the cost of boring, with bentonite solution and
temporary casing of appropriate length for setting out and removal of same and
the length of the pile to be embedded in the pile cap etc. all complete, including
removal of excavated earth with all lifts and leads (Length of pile for payment
shall be measured upto bottom of pile cap).
14.2.1 20.2.6 750 mm dia piles 2690 metre 4944.35
Rupees Four Thousand
Nine Hundred Forty Four
and Paise Thirty Five Only
13300302
14.3 20.6
Vertical load testing of piles in accordance with IS 2911 (Part IV) including
installation of loading platform and preparation of pile head or construction of test
cap and dismantling of test cap after test etc. complete as per specification & the
direction of Engineer in-charge.
14.3.1 20.6.2 Single pile above 50 tonne and upto 100 tonne capacity
14.3.1.1 20.6.2.1 Initial test 269 per test 46808.45
Rupees Forty Six
Thousand Eight Hundred
Eight and Paise Forty Five
Only
12591473
15.0 HORTICULTURE & LANDSCAPING
15.1 23.1
Trenching in ordinary soil up to a depth of 60 cm including removal and stacking
of serviceable materials and then disposing of surplus soil, by spreading and
neatly leveling within a lead of 50 m and making up the trenched area to proper
levels by filling with earth or earth mixed with sludge or/and manure before and
after flooding trench with water (excluding cost of imported earth, sludge or
manure).
30 cum 37.10Rupees Thirty Seven and
Paise Ten Only 1113
15.2 23.4
Supplying and stacking at site dump manure from approved source, including
carriage up to 1 km (manure measured in stacks will be reduced by 8% for
payment) :
a) 23.4.1 Screened through sieve of I.S. designation 20 mm 74 cum 167.60
Rupees One Hundred
Sixty Seven and Paise
Sixty Only
12469
b) 23.4.2 Screened through sieve of I.S. designation 16 mm 74 cum 184.85
Rupees One Hundred
Eighty Four and Paise
Eighty Five Only
13753
c) 23.4.3 Screened through sieve of I.S. designation 4.75 mm 74 cum 198.65
Rupees One Hundred
Ninety Eight and Paise
Sixty Five Only
14780
Page 29 of 66
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.NoDSR Code
No_ 2013Description
Total
Qty.Unit Rate Rate In Words DSR-Amount
15.3 23.7 Fine dressing of the ground 15 100sqm 175.30
Rupees One Hundred
Seventy Five and Paise
Thirty Only
2608
15.4 23.8
Spreading of sludge, dump manure and / or good earth in required thickness as
per direction of Officer-in-charge (Cost of sludge, dump manure and / or good
earth to be paid separately).
223 cum 25.15Rupees Twenty Five and
Paise Fifteen Only 5613
15.5 23.9Mixing earth and sludge or manure in the required proportion specified or
directed by the Officer-in-charge..223 cum 17.25
Rupees Seventeen and
Paise Twenty Five Only 3850
15.6 23.10
Grassing with selection No.1 grass including watering and maintenance of the
lawn for 30 days or more till the grass forms a thick lawn, free from weeds and fit
for mowing including supplying good earth, if needed (the good earth if needed
shall be paid for separately).
a) 23.10.1 In rows 5 cm apart in both directions 7.44 100 sqm 841.25
Rupees Eight Hundred
Forty One and Paise
Twenty Five Only
6259
b) 23.10.2 With grass Turf 7.44 100 sqm 634.30
Rupees Six Hundred Thirty
Four and Paise Thirty
Only
4719
15.7 23.13
Preparation of beds for hedging and shrubbery by excavating 60 cm deep and
trenching the excavated base to a further depth of 30 cm, refilling the excavated
earth after breaking clods and mixing with sludge or manure in the ratio of 8:1 (8
parts of stacked volume of earth after reduction by 20% : one part of stacked
volume of sludge or manure after reduction by 8%), flooding with water, filling
with earth if necessary, watering and finally fine dressing, leveling etc. including
stacking and disposal of materials declared unserviceable and surplus earth by
spreading and leveling as directed, within a lead of 50 m, lift up to 1.5 m
complete (cost of sludge, manure or extra earth to be paid for separately).
30 cum 105.20Rupees One Hundred Five
and Paise Twenty Only 3156
15.8 23.14
Digging holes in ordinary soil and refilling the same with the excavated earth
mixed with manure or sludge in the ratio of 2:1 by volume (2 parts of stacked
volume of earth after reduction by 20% : 1 part of stacked volume of manure
after reduction by 8%) flooding with water, dressing including removal of rubbish
and surplus earth, if any, with all leads and lifts (cost of manure, sludge or extra
good earth if needed to be paid for separately) :
a) 23.14.1 Holes 1.2 m dia and 1.2 m deep. 20 each 211.90
Rupees Two Hundred
Eleven and Paise Ninety
Only
4238
b) 23.14.2 Holes 90 cm dia, and 90 cm deep. 30 each 90.90Rupees Ninety and Paise
Ninety Only 2727
Page 30 of 66
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.NoDSR Code
No_ 2013Description
Total
Qty.Unit Rate Rate In Words DSR-Amount
15.9 23.28
Preparation of mounds of various size and shape by available excavated /
supplied earth in layers not exceeding 20 cm in depth, breaking clods, watering
of each layer, dressing etc., lead upto 50 meter and lift upto 1.5 m complete as
per direction of Officer-in-charge.;
112 cum 215.60
Rupees Two Hundred
Fifteen and Paise Sixty
Only
24061
15.10 23.30
Providing Square Cement Concrete pots of specified size, cast with cement
concrete of nominal mix 1:2:4 (1 cement : 2 coarse sand : 4 graded stone
aggregate 60 mm nominal size), reinforced with 7 nos. ( 3 nos horizontal & 4 nos
vertical "U" shape) M.S. wires of 3.5 mm dia as per design, including required
form work, finishing with cement punning on exposed surface, curing for
specified period and stacking in required rows & height , all complete as per
direction of Officer-in-charge.
23.30.1Top inner width 35 cm, outer bottom width 25 cm, total height 35 cm and wall
thickness 25.4 mm 10 each 200.55
Rupees Two Hundred and
Paise Fifty Five Only 1955
15.11 23.16
Providing and fixing M.S. flat iron tree guard 60 cm dia and 2 m high, above
ground consisting 4 nos 25 x 6 mm, 2.25 m long and 8 nos 25 x 3 mm 2 m long
verticals M.S. flats, riveted to 3 nos 25 x 6 mm M.S. flat iron rings in two halves,
fixing together at site with required six numbers of 8 mm dia. and 30 mm long
bolts, including painting two coats with synthetic enamel paint of approved brand
and manufacture over a coat of primer. One name plate of 1 mm thick M.S.
sheet of size 250x100 mm shall be welded to the tree guard near the middle
height and lettered CPWD / PWD/ any other approved name. The tree guard
shall be suitably fixed to the ground by embedding four legs of tree guard in pits
of suitable dia and to a depth of 25 cm, refilling the pits with soil and ramming,
complete in all respect as per satisfaction and direction of Officer-in-charge.
20 each 2884.15
Rupees Two Thousand
Eight Hundred Eighty Four
and Paise Fifteen Only
57683
15.12 23.15
Half brick circular tree guard in bricks, internal diameter 1.25 metre and height
1.2 metre above ground and 0.20 m below ground, bottom two courses laid dry
and top three courses in cement mortar 1:6 (1 cement : 6 fine sand) and the
intermediate courses being in dry honey comb masonry as per design complete :
23.15.1 With common burnt clay F.P.S. (non modular) bricks of class designation 5 30 each 1241.55
Rupees One Thousand
Two Hundred Forty One
and Paise Fifty Five Only
37247
15.13 23.29
Providing Circular Cement Concrete pots of specified size, cast with cement
concrete of nominal mix 1:2:4 (1 cement: 2 coarse sand: 4 graded stone
aggregate 6 mm nominal size), reinforced with 7 nos ( 3 nos horizontal & 4 nos
vertical "U" shape) M.S. wires of 3.5 mm dia as per design, including required
form work, finishing with cement punning on exposed surface, curing for
specified period and stacking in required rows & height, all complete as per
direction of Officer-in-charge.
Page 31 of 66
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.NoDSR Code
No_ 2013Description
Total
Qty.Unit Rate Rate In Words DSR-Amount
23.29.1Top inside dia 35 cm, outer bottom dia 25 cm, total height 35 cm with wall
thickness of 25.4 mm10 each 166.25
Rupees One Hundred
Sixty Six and Paise Twenty
Five Only
1663
16.0 ROAD WORKS :
16.1 16.1
Preparation and consolidation of sub grade with power road roller of 8 to 12
tonne capacity after excavating earth to an average of 22.5 cm depth, dressing
to camber and consolidating with road roller including making good the
undulations etc. and re-rolling the sub grade and disposal of surplus earth with
lead upto 50 metres.
2532 sqm 73.55Rupees Seventy Three
and Paise Fifty Five Only 186232
16.2 16.2Extra for compaction of earth work in embankment under optimum moisture
conditions to give at least 95% of the maximum dry density (proctor density).760 cum 9.30
Rupees Nine and Paise
Thirty Only 7064
16.3 16.3 Supplying and stacking at site
a) 16.3.1 90 mm to 45 mm size stone aggregate 380 cum 1121.90
Rupees One Thousand
One Hundred Twenty One
and Paise Ninety Only
426104
b) 16.3.2 63 mm to 45 mm size stone aggregate 380 cum 1272.90
Rupees One Thousand
Two Hundred Seventy
Two and Paise Ninety
Only
483455
c) 16.3.6 Stone screening 13.2 mm nominal size (type A) 190 cum 1410.20
Rupees One Thousand
Four Hundred Ten and
Paise Twenty Only
267801
d) 16.3.7 Stone screening 11.2 mm nominal size (type A) 190 cum 1453.80
Rupees One Thousand
Four Hundred Fifty Three
and Paise Eighty Only
276081
e) 16.3.10 Moorum 76 cum 646.55
Rupees Six Hundred Forty
Six and Paise Fifty Five
Only
49113
16.4 16.4
Laying spreading and compacting stone aggregate of specified sizes to WBM
specifications including spreading in uniform thickness, hand picking, rolling with
3 wheeled road/vibratory roller 8-10 tonne in stages to proper grade and camber,
applying and brooming requisite type of screening/binding material to fill up
interstics of coarse aggregate watering and compacting to the required density.
380 cum 388.85
Rupees Three Hundred
Eighty Eight and Paise
Eighty Five Only
147688
16.5 16.75
Providing and laying C.C. pavement of mix M-25 with ready mixed concrete from
batching plant. The ready mixed concrete shall be laid and finished with screed
board vibrator , vacuum dewatering process and finally finished by floating,
brooming with wire brush etc. complete as per specifications and directions of
Engineer-in-charge. (The panel shuttering work shall be paid for separately).
982 cum 6248.00
Rupees Six Thousand Two
Hundred Forty Eight and
Paise Zero Only
6137898
Page 32 of 66
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.NoDSR Code
No_ 2013Description
Total
Qty.Unit Rate Rate In Words DSR-Amount
(Note:- Cement content considered in this item is @ 330 kg/cum. Excess/less
cement used as per design mix is payable/ recoverable separately).
16.6 16.44Extra for providing and mixing hardening compound of approved quality as per
manufacturer's specification in cement concrete.491.19 litre 46.45
Rupees Forty Six and
Paise Forty Five Only 22816
16.7 16.45 Providing & Fixing in position premoulded joint filler in expansion joint 3425
per cm
depth per
cm width
per m
length
2.45Rupees Two and Paise
Forty Five Only 8391
16.8 16.46Providing and laying in position bitumen hot sealing compound for expansion
joints etc.
16.9 16.46.1 16.46.1 Using grade 'A' sealing compound. 3425
per cm
depth per
cm width
per m
length
1.90Rupees One and Paise
Ninety Only 6508
PAINTING ROAD / RUNWAY MARKING
16.10 16.47
Painting runway/taxi track/apron marking with adequate no. of coats to give
uniform finish with road marking paint of superior make as approved by the
Engineer-in-charge i/c cleaning the surface of all dirt, scales, oil, grease and
other foreign material etc. and lining out complete
16.10.1 16.47.1 New work (Two or more coats) 548 sqm 104.45
Rupees One Hundred
Four and Paise Forty Five
Only
57239
16.11 16.49
Making bell mouth opening/ entrance of size 100x50x50cm for drainage pipe
under footpath including providing cement concrete 1:3:6 (1 cement : 3 coarse
sand : 6 graded stone aggregate 20mm nominal size) for shape of bell mouth
including plastering providing and fixing precast R.C.C./ S.F.R.C. slab including
plastering with cement mortar 1:3 (1 cement : 3 fine sand) of 6 mm thickness on
exposed surface of the slab & bell mouth including centring, shuttering & neat
cement punning inside the bell mouth etc. all complete.
18 each 1664.85
Rupees One Thousand Six
Hundred Sixty Four and
Paise Eighty Five Only
30411
16.12 16.68
Providing and laying 60mm thick factory made cement concrete interlocking
paver block of M-30 grade made by block making machine with strong vibratory
compaction and of approved size and design/shape laid in required colour and
pattern over and including 50 mm thick compacted of coarse sand, filling the
joints with coarse sand etc. all complete as per direction of engineer-in-charge.
27 sqm 557.45
Rupees Five Hundred Fifty
Seven and Paise Forty
Five Only
15274
Page 33 of 66
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.NoDSR Code
No_ 2013Description
Total
Qty.Unit Rate Rate In Words DSR-Amount
16.13 16.69
Providing and laying at or near ground level factory made kerb stone of M-25
grade cement in position to the required line , level and curvature jointed with
cement mortar 1:3 (1 cement : 3 coarse sand) including making joints with or
without grooves (thickness of joints except sharp curve shall not be more than
5mm) including making drainage opening wherever required complete etc. as
per direction of engineer-in-charge (length of finished kerb edging shall be
measured for payment).(Precast C.C. kerb stone shall be approved by engineer-
in-charge).
31 cum 5236.95
Rupees Five Thousand
Two Hundred Thirty Six
and Paise Ninety Five Only
163114
16.14 19.6
Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with
collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1
cement : 2 fine sand) including testing of joints etc. complete :
16.14.1 19.6.7 600 mm dia. R.C.C. pipe 18 metre 1358.65
Rupees One Thousand
Three Hundred Fifty Eight
and Paise Sixty Five Only
24909
16.16 24.9
Providing and fixing factory made precast RCC perforated drain covers, having
concrete of strength not less than M-25, of size 1000 x 450x50 mm, reinforced
with 8 mm dia four no longitudinal & 9 nos cross sectional T.M.T. hoop bars,
including providing 50 mm dia perforations @ 100 to 125 mm c/c, including
providing edge binding with M.S. flats of size 50 mm x 1.6 mm complete, all as
per direction of Engineer-in-charge.
18 each 958.80
Rupees Nine Hundred
Fifty Eight and Paise
Eighty Only
17578
CIVIL TOTAL 243946180
Page 34 of 66
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.NoDSR Code
No_ 2013Description
Total
Qty.Unit Rate Rate In Words DSR-Amount
A. INTERNAL PLUMBING WORK
SUB HEAD - I - SANITARY FIXTURES
1 17.78
Providing and fixing white vitreous china extended wall mounting water
closet of size 780 x 370 x 690 mm of approved shape including providing &
fixing white vitreous china cistern with dual flush fitting, of flushing capacity
3 litre/6 litre (adjustable to 4 litre/8 litres), including seat cover, and cistern
fittings, nuts, bolts and gasket etc complete.
W.C. pan with ISI marked white solid plastic seat & lid. 32 Each 9965.25
Rupees Nine Thousand
Nine Hundred Sixty Five
and Paise Twenty Five
Only
318888
2 17. 10
Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per
IS 13983 with C.I. brackets and stainless steel plug 40 mm including
painting of fittings and brackets, cutting and making good the walls
wherever required:
2.1 17.10.2.2 Kitchen sink without drain board 610 x 460mm bowl depth 200 mm (Pantry) 6 Each 3936.55
Rupees Three Thousand
Nine Hundred Thirty Six
and Paise Fifty Five Only
23619
3 17.31
Providing and fixing 600 x 450mm beveled edge mirror of superior glass
(of approved quality) complete with 6 mm thick hard board ground fixed to
wooden cleats with C.P. brass screws and washers complete.
64 Each 762.55
Rupees Seven Hundred
Sixty Two and Paise Fifty
Five Only
48803
4 17.71
Providing and fixing PTMT liquid soap container 109 mm wide,
125 mm high and 112 mm distance from wall of standard shape with
bracket of the same materials with snap fittings of approved quality
and colour, weighing not less than 105 gms.
64 Each 181.75
Rupees One Hundred
Eighty One and Paise
Seventy Five Only
11632
5 17.1
Providing & fixing water closet squatting pan (Indian W.C. pan) with 100
mm sand cast iron P or S trap, 10 litre low level white P.V.C. flushing
cistern with manually controlled device (handle lever) conforming to IS:
7231 with all fittings & fixture complete including cutting and making good
the walls & floors wherever required
5.1 17.1.1White vitreous china Orissa pattern W.C. pan of size 580 x 440 mm with
integral type foot restsRO Each 3265.25
Rupees Three Thousand
Two Hundred Sixty Five
and Paise Twenty Five
Only
PLUMBING WORKS
Page 35 of 66
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.NoDSR Code
No_ 2013Description
Total
Qty.Unit Rate Rate In Words DSR-Amount
6 17.34 Providing and fixing toilet paper holder : 32 Each 339.85
Rupees Three Hundred
Thirty Nine and Paise
Eighty Five Only
10875
17.34.1 C.P. brass
SUB HEAD - II - SOIL, WASTE AND VENT PIPES, RAIN WATER PIPES
7 17. 35 Providing and fixing soil, waste and vent pipes.
7.1 17.35.1 100 mm dia.
7.1.1 17.35.1.2 Centrifugally cast (spun) iron socketed pipe as per IS:3989 1081 Metre 952.50
Rupees Nine Hundred
Fifty Two and Paise Fifty
Only
1029653
7.1.2 17.35.2 75 mm dia
7.2.1 17.35.2.2 Centrifugally cast (spun) iron socketed pipe as per IS:3989 135 Metre 787.70
Rupees Seven Hundred
Eighty Seven and Paise
Seventy Only
106340
8 17. 37
Providing and fixing M.S holder-bat clamps of approved design to Sand
Cast iron/ cast iron (spun) pipe embedded in and including cement
concrete blocks 10x10x10 cm of 1:2:4 mix (1 cement : 2 coarse sand : 4
graded stone aggregate 20mm nominal size) including cost of cutting holes
and making good the walls etc.
8.1 17.37.1 for 100 mm dia. pipe 194 Each 140.65
Rupees One Hundred
Forty and Paise Sixty Five
Only
27286
8.2 17.37.2 for 75 mm dia. pipe 28 Each 138.35
Rupees One Hundred
Thirty Eight and Paise
Thirty Five Only
3874
9 17. 38Providing and fixing bend of required degree with access door, insertion
rubber washer 3 mm thick, bolts and nuts complete.
9.1 17.38.1 100 mm
9.1.1 17.38.1.2 Sand cast iron S&S as per IS-3989 32 Each 384.45
Rupees Three Hundred
Eighty Four and Paise
Forty Five Only
12302
9.2 17.38.2 75 mm 6 Each 317.50
Rupees Three Hundred
Seventeen and Paise Fifty
Only
1905
9.2.1 17.38.2.2 Sand cast iron S&S as per IS-3989Page 36 of 66
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.NoDSR Code
No_ 2013Description
Total
Qty.Unit Rate Rate In Words DSR-Amount
10 17. 39 Providing and fixing plain bend of required degree.
10.1 17.39.1 100 mm
10.1.1 17.39.1.2 Sand cast iron S&S as per IS:3989 144 Each 334.50
Rupees Three Hundred
Thirty Four and Paise Fifty
Only
48168
10.2 17.39.2 75 mm
10.2.1 17.39.2.2 Sand cast iron S&S as per IS:3989 24 Each 247.80
Rupees Two Hundred
Forty Seven and Paise
Eighty Only
5947
10 17. 40 Providing and fixing heel rest sanitary bend.
10.3.1 17.40.1 100 mm dia
10.3.1.
117.40.1.2 sand cast iron S&S as per IS-3989 8 Each 370.50
Rupees Three Hundred
Seventy and Paise Fifty
Only
2964
11 17. 43Providing and fixing single equal plain junction of required degree with
access door, insertion rubber washer 3mm thick, bolts and nuts complete.
11.1 17.43.1 100x100x100mm
11.1.1 17.43.1.2 sand cast iron S&S as per IS-3989 32 Each 622.55
Rupees Six Hundred
Twenty Two and Paise
Fifty Five Only
19922
12 17. 44 Providing and fixing single equal plain junction of required degree
12.1 17.44.1 100x100x100mm
12.1.1 17.44.1.2 sand cast iron S&S as per IS-3989 122 Each 574.90
Rupees Five Hundred
Seventy Four and Paise
Ninety Only
70138
13 17. 47Providing and fixing single unequal junction of required degree with access
door, insertion rubber washer 3mm thick, bolts and nuts complete.
13.1 17. 47.1 100x100x75mm
13.1.1 17.47.1.2 sand cast iron S&S as per IS-3989 0 Each 790.55
Rupees Seven Hundred
Ninety and Paise Fifty
Five Only
0
14 17. 56 Providing and fixing terminal guard.
14.1 17.56.1 100 mm
Page 37 of 66
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.NoDSR Code
No_ 2013Description
Total
Qty.Unit Rate Rate In Words DSR-Amount
14.1.1 17.56.1.2 sand cast iron S&S as per IS-3989 8 Each 433.20
Rupees Four Hundred
Thirty Three and Paise
Twenty Only
3466
15 17. 57 Providing and fixing collar
15.1 17.57.1 100 mm
15.1.1 17.57.1.2 Sand cast iron S&S as per IS-3989 8 Each 317.05
Rupees Three Hundred
Seventeen and Paise Five
Only
2536
16 17. 58Providing lead caulked joints to sand cast iron /centrifugally cast (spun) iron
pipes and fittings of diameter:
16.1 17.58.1 100 mm 1079 Each 232.30
Rupees Two Hundred
Thirty Two and Paise
Thirty Only
250652
16.2 17.58.2 75 mm 100 Each 196.20
Rupees One Hundred
Ninety Six and Paise
Twenty Only
19714
16.3Derived Rate
from 17.58150mm 0 Each 311.80
Rupees Three Hundred
Eleven and Paise Eighty
Only
0
17 17. 59Providing and fixing M.S. stays and clamps for sand cast iron / centrifugally
cast (spun) iron pipes of diameter :
17.1 17.59.1 100 mm 8 Each 67.35Rupees Sixty Seven and
Paise Thirty Five Only 539
17.2 17.59.2 75 mm 28 Each 56.15Rupees Fifty Six and Paise
Fifteen Only 1572
Page 38 of 66
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.NoDSR Code
No_ 2013Description
Total
Qty.Unit Rate Rate In Words DSR-Amount
18 17. 60
Providing and fixing trap of self cleansing with screwed down or hinged
grating with or without vent arm complete, including cost of cutting and
making good the walls and floors:
18.1 17.60.1 100 mm inlet and 100 mm outlet
18.1.1 17.60.1.1 Sand cast iron S&S as per IS-3989 72 Each 938.05
Rupees Nine Hundred
Thirty Eight and Paise Five
Only
67540
18.2 17.60.2 100 mm inlet and 75 mm outlet
18.2.1 17.60.2.1 Sand cast iron S&S as per IS-3989 0 Each 976.40
Rupees Nine Hundred
Seventy Six and Paise
Forty Only
0
19 17. 65
Painting sand cast iron / centrifugally cast (spun) iron soil, waste vent
pipes and fittings with paint of any colour such as chocolate, grey, or buff
etc. over a coat of primer (of approved quality) for new work:
19.1 17.65.1 100 mm diameter pipe 1031 Metre 33.85Rupees Thirty Three and
Paise Eighty Five Only 34899
19.2 17.65.2 75 mm diameter pipe 135 Metre 25.90Rupees Twenty Five and
Paise Ninety Only 3497
19.3Derived Rate
from 17.65150 mm diameter pipe 30 Metre 43.10
Rupees Forty Three and
Paise Ten Only 1293
20 12. 44Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15
cm diameter and weighing not less than 440 grams19 Each 37.25
Rupees Thirty Seven and
Paise Twenty Five Only 708
21 12.22
Making 'Khurras' size 450 X 450 mm with average minimum thickness of
50mm cement concrete 1:2:4 (1 cement : 2 Coarse sand : 4 graded stone
aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x 1m x 400
micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand)
and a coat of neat cement rounding the edge sand making and finishing the
outlet complete.
14 Each 167.45
Rupees One Hundred
Sixty Seven and Paise
Forty Five Only
2344
22 12.41
Providing and fixing on wall face unplasticised Rigid PVC rain water
pipes conforming to IS : 13592 Type A, including jointing with seal
ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.
(i) Single socketed pipes.
Page 39 of 66
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.NoDSR Code
No_ 2013Description
Total
Qty.Unit Rate Rate In Words DSR-Amount
22.1 12.41.2 110 mm diameter 5 metre 218.60
Rupees Two Hundred
Eighteen and Paise Sixty
Only
1093
23 12.42
Providing and fixing on wall face unplasticised - PVC moulded fittings/
accessories for unplasticised Rigid PVC rain water pipes conforming
to IS : 13592 Type A, including jointing with seal ring conforming to
IS : 5382, leaving 10 mm gap for thermal expansion.
23.1 12.42.1 Coupler
12.42.1.2 110 mm 2 metre 133.55
Rupees One Hundred
Thirty Three and Paise
Fifty Five Only
267
23.2 12.42.4 Single tee without door
12.42.4.2 110x110x110 mm 2 metre 244.95
Rupees Two Hundred
Forty Four and Paise
Ninety Five Only
490
23.3 12.42.5 Bend 87.5°
12.42.5.2 110 mm bend 2 metre 160.25
Rupees One Hundred
Sixty and Paise Twenty
Five Only
321
23.4 12.42.6 Shoe (Plain)
12.42.6.2 110 mm Shoe 2 metre 290.35
Rupees Two Hundred
Ninety and Paise Thirty
Five Only
581
24 12
Providing and fixing unplasticised -PVC pipe clips of approved design
to unplasticised - PVC rain water pipes by means of 50x50x50 mm
hard wood plugs, screwed with M.S. screws of required length,including
cutting brick work and fixing in cement mortar 1:4 (1 cement
: 4 coarse sand) and making good the wall etc. complete.
24.1 12.43.2 110 mm 20 each 173.75
Rupees One Hundred
Seventy Three and Paise
Seventy Five Only
3475
Page 40 of 66
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.NoDSR Code
No_ 2013Description
Total
Qty.Unit Rate Rate In Words DSR-Amount
SUB HEAD - III - WATER SUPPLY
25 18. 8
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having
thermal stability for hot & cold water supply including all CPVC plain &
brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing.
This includes jointing of pipes & fittings with one step CPVC solvent cement
and the cost of cutting chases and making good the same including testing
of joints complete as per direction of Engineer in Charge.
Concealed work including cutting chases and making good the walls etc.
25.1 18.8.1 15 mm nominal outer dia pipes (SDR-11) 1122 Metre 254.95
Rupees Two Hundred Fifty
Four and Paise Ninety
Five Only
286054
25.2 18.8.2 20 mm nominal outer dia pipes (SDR-11) 434 Metre 281.35
Rupees Two Hundred
Eighty One and Paise
Thirty Five Only
122106
25.3 18.8.3 25 mm nominal outer dia pipes (SDR-11) 298 Metre 336.25
Rupees Three Hundred
Thirty Six and Paise
Twenty Five Only
100203
25.4 18.8.4 32 mm nominal outer dia pipes (SDR-11) 48 Metre 407.40
Rupees Four Hundred
Seven and Paise Forty
Only
19555
26 18.10Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c
cutting and making good the walls etc. (Internal work):
Exposed on Wall
26.1 18.10.1 15 mm dia nominal bore 15 Metre 181.35
Rupees One Hundred
Eighty One and Paise
Thirty Five Only
2720
26.2 18.10.2 20 mm dia nominal bore 40 Metre 221.50
Rupees Two Hundred
Twenty One and Paise
Fifty Only
8860
26.3 18.10.3 25 mm dia nominal bore 125 Metre 282.30
Rupees Two Hundred
Eighty Two and Paise
Thirty Only
35288
Page 41 of 66
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.NoDSR Code
No_ 2013Description
Total
Qty.Unit Rate Rate In Words DSR-Amount
26.4 18.10.4 32mm dia nominal bore 235 Metre 333.50
Rupees Three Hundred
Thirty Three and Paise
Fifty Only
78373
26.5 18.10.5 40 mm dia nominal bore 210 Metre 413.25
Rupees Four Hundred
Thirteen and Paise Twenty
Five Only
86783
26.6 18.10.6 50 mm dia nominal bore 175 Metre 512.10
Rupees Five Hundred
Twelve and Paise Ten
Only
89618
27 18. 17Providing and fixing gun metal gate valve with C.I. wheel of approved
quality (screwed end)
27.1 18.17.1 25 mm nominal bore 14 Each 427.80
Rupees Four Hundred
Twenty Seven and Paise
Eighty Only
5989
27.2 18.17.2 32 mm nominal bore 10 Each 500.35Rupees Five Hundred and
Paise Thirty Five Only 5004
27.3 18.17.3 40 mm nominal bore 11 Each 584.20
Rupees Five Hundred
Eighty Four and Paise
Twenty Only
6426
27.4 18.17.4 50 mm nominal bore 7 Each 749.40
Rupees Seven Hundred
Forty Nine and Paise Forty
Only
5246
28 18. 38Painting G.I. pipes and fittings with synthetic enamel white paint over a
ready mixed priming coat, both of approved quality for new work.
28.1 18.38.1 15 mm nominal outer dia pipes 15 Metre 8.60Rupees Eight and Paise
Sixty Only 129
28.2 18.38.2 20 mm nominal outer dia pipes 40 Metre 10.10Rupees Ten and Paise
Ten Only 404
28.3 18.38.3 25 mm nominal outer dia pipes 125 Metre 13.35Rupees Thirteen and
Paise Thirty Five Only 1669
28.4 18.38.4 32 mm nominal outer dia pipes 235 Metre 15.75Rupees Fifteen and Paise
Seventy Five Only 3701
Page 42 of 66
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.NoDSR Code
No_ 2013Description
Total
Qty.Unit Rate Rate In Words DSR-Amount
28.5 18.38.5 40 mm nominal outer dia pipes 210 Metre 18.70Rupees Eighteen and
Paise Seventy Only 3927
28.6 18.38.6 50 mm nominal outer dia pipes 175 Metre 22.00Rupees Twenty Two and
Paise Zero Only 3850
28.7 D.R. - 18.38.6 65 mm nominal outer dia pipes 80 Metre 23.28Rupees Twenty Three and
Paise Twenty Eight Only 1862
28.8 D.R. - 18.38.6 80 mm nominal outer dia pipes 50 Metre 26.30Rupees Twenty Six and
Paise Thirty Only 1315
28.9 D.R. - 18.38.6 100 mm nominal outer dia pipes 0 Metre 34.04Rupees Thirty Four and
Paise Three Only 0
29 18. 49Providing and fixing C.P brass bib cock of approved quality conforming to
IS:8931.
29.1 18.49.1 15 mm nominal bore 5 Each 458.40
Rupees Four Hundred
Fifty Eight and Paise Forty
Only
2292
30 18. 52Providing and fixing C.P. brass stop cock (concealed) of standard design
and of approved make confirming to IS:8931
30.1 18.52.1 15 mm nominal bore 32 Each 618.70
Rupees Six Hundred
Eighteen and Paise
Seventy Only
19798
31 18. 53Providing and fixing C.P. brass angle valve for basin, cistern and geyser
points of approved quality conforming to IS:8931.
31.1 18.53.1 15 mm nominal bore 96 Each 506.70Rupees Five Hundred Six
and Paise Seventy Only 48643
Page 43 of 66
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.NoDSR Code
No_ 2013Description
Total
Qty.Unit Rate Rate In Words DSR-Amount
Sub Head IV Sewargw & Drainage
32 19. 1
Providing, laying and jointing glazed stoneware pipes class SP-1 with
stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine
sand) including testing of joints etc. complete :
32.1 19.1.2 150 mm diameter 190 Metre 301.90
Rupees Three Hundred
One and Paise Ninety
Only
57361
32.2 19.1.3 200 mm diameter 150 Metre 447.25
Rupees Four Hundred
Forty Seven and Paise
Twenty Five Only
67088
32.3 19.1.4 250 mm diameter 20 Metre 676.75
Rupees Six Hundred
Seventy Six and Paise
Seventy Five Only
13535
33 19.2
Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10
graded stone aggregate 40 mm nominal size) all-round S.W. pipes
including bed concrete as per standard design :
33.1 19.2.2 150 mm diameter 190 Metre 664.80
Rupees Six Hundred Sixty
Four and Paise Eighty
Only
126312
33.2 19.2.3 200 mm diameter 150 Metre 774.95
Rupees Seven Hundred
Seventy Four and Paise
Ninety Five Only
116243
33.3 19.2.4 250 mm diameter 20 Metre 896.15
Rupees Eight Hundred
Ninety Six and Paise
Fifteen Only
17923
34 19. 4
Providing and fixing square-mouth S.W. gully trap grade ‘A’' complete with
C.I. grating, brick masonry chamber with water tight C.I. cover with frame of
300x300 mm size (inside) the weight of cover to be not less than 4.50 kg
and frame to be not less than
34.1 19.4.3 180 x 150mm size P type
34.1.1 19.4.3.1 F.P.S. Bricks class designation 75 2 Each 1635.00
Rupees One Thousand Six
Hundred Thirty Five and
Paise Zero Only
3270
35 19.6
Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with
collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1
cement : 2 fine sand) including testing of joints etc. complete.
35.1 19.6.2 150 mm dia R.C.C pipe 10 Metre 340.35
Rupees Three Hundred
Forty and Paise Thirty
Five Only
3404
Page 44 of 66
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.NoDSR Code
No_ 2013Description
Total
Qty.Unit Rate Rate In Words DSR-Amount
35.2 19.6.3 250 mm dia R.C.C pipe 110 Metre 455.90
Rupees Four Hundred
Fifty Five and Paise Ninety
Only
50149
35.3 19.6.4 300 mm dia R.C.C pipe 60 Metre 494.35
Rupees Four Hundred
Ninety Four and Paise
Thirty Five Only
29661
35.4 19.6.5 400 mm dia R.C.C pipe 30 Metre 688.90
Rupees Six Hundred
Eighty Eight and Paise
Ninety Only
20667
36 19.27
Constructing brick masonry road gully chamber 50x45x60 cm with bricks in
cement mortar 1:4 (1 cement : 4 coarse sand) including 500x450 mm pre-
cast R.C.C. horizontal grating with frame complete
as per standard design :
0 Nos. 3774.95
Rupees Three Thousand
Seven Hundred Seventy
Four and Paise Ninety
Five Only
0
37
Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10
graded stone aggregate 40 mm nominal size) up to haunches of S.W./
R.C.C pipes including bed concrete as per standard design
37.1 19.3.2 150 mm dia 10 RM 418.70
Rupees Four Hundred
Eighteen and Paise
Seventy Only
4187
37.2 19.3.4 250 mm dia 110 RM 572.95
Rupees Five Hundred
Seventy Two and Paise
Ninety Five Only
63025
37.3 19.3.5 300 mm dia 60 RM 661.10Rupees Six Hundred Sixty
One and Paise Ten Only 39666
37.4D.R. from
19.3.5400 mm dia 30 RM 1078.85
Rupees One Thousand
Seventy Eight and Paise
Eighty Five Only
32366
38 19.7
Constructing brick masonry manhole cement mortar 1:4 (1 cement: 4
coarse sand) R.C.C. top slab with 1:2:4 mix (1cement: 2 coarse sand: 4
graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8
mix (1cement: 4 coarse sand: 8 graded stone aggregate 40 mm nominal
size) inside plastering 12mm thick with cement mortar 1:3 (1 cement: 3
coarse sand) finished with floating coat of neat cement and making
necessary channels in cement concrete 1:2:4 (1 cement: 2 coarse sand: 4
graded stone aggregate 20mm nominal size) finished with a floating coat of
neat cement complete as per standard design.
Page 45 of 66
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.NoDSR Code
No_ 2013Description
Total
Qty.Unit Rate Rate In Words DSR-Amount
38.1 19.7.1
Inside size 90 x 80 cm and 45 cm deep including C.I. cover with frame (light
duty) 455 x 610 mm internal dimensions total weight of cover and frame to
be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg)
38.1.1 19.7.1.1 With F.P.S. bricks with class designation 75 19 Each 8062.70
Rupees Eight Thousand
Sixty Two and Paise
Seventy Only
153191
38.2 19.7.2
Inside size 120x90 cm and 90 cm deep including C.I. cover with frame
(medium duty) 500 mm internal diameter, total weight of cover and frame to
be not less than 116 kg (weight of cover 58 kg and weight of frame
58 kg) :
38.2.1 19.7.2.1With common burnt clay F.P.S. (non modular) bricks of class designation
7.514 Each 17592.00
Rupees Seventeen
Thousand Five Hundred
Ninety Two and Paise
Zero Only
246288
39 19.8 Extra depth for manholes
39.1 19.8.1.1 Size 90 x 80 cm (With F.P.S. bricks with class designation 75) 3 Metre 5481.40
Rupees Five Thousand
Four Hundred Eighty One
and Paise Forty Only
16444
19.8.2 Size 120x90 cm
39.2 19.8.2.1With common burnt clay F.P.S. (non modular) bricks of
class designation 7.53 Metre 6563.00
Rupees Six Thousand Five
Hundred Sixty Three and
Paise Zero Only
19689
40 As per DSR
Constructing brick masonary basement drain with bricks of class
designation 7.5 in cement mortar 1:4 (1 cement : 4 coarse sand) , 10cm
thick bed concrete 1:5:10 (1 cement : 5 coarse and : 10 graded stone
aggregate 40 mm nominal size) with a floating coat of neat cement inside
the drain, its top and exposed side and 12mm thick external plaster with
cement mortar 1:6 (1 cement : 6 coarse sand).
40.1 As per DSR 30 cm drain 50cm average depth 600 Metre 763.86
Rupees Seven Hundred
Sixty Three and Paise
Eighty Five Only
458314
41 As per DSRProviding and fixing in position SFRC drain covers including perforation as
required over drains for the following sizes :-
Page 46 of 66
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.NoDSR Code
No_ 2013Description
Total
Qty.Unit Rate Rate In Words DSR-Amount
41.1 As per DSR for 30 cm wide drain sleeve size 75cm x 60cm & 7cm thick 600 Metre 252.07
Rupees Two Hundred Fifty
Two and Paise Seven
Only
151243
42 2.10
Excavating trenches of required width for pipes, cables, etc including
excavation for sockets, and dressing of sides, ramming of bottoms, depth
upto 1.5 m, including getting out the excavated soil, and then returning the
soil as required, in layers not exceeding 20 cm in depth, including
consolidating each deposited layer by ramming, watering, etc. and
disposing of surplus excavated soil as directed, within a lead of 50 m :
42.1 2.10.1 All kinds of soil
12.1.1 2.10.1.2 Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia 570 RM 192.75
Rupees One Hundred
Ninety Two and Paise
Seventy Five Only
109868
43 2.11
Extra for excavating trenches for pipes, cables etc. in all kinds of soil for
depth exceeding 1.5 m, but not exceeding 3 m. (Rate is over orresponding
basic item for depth upto 1.5 metre).
90 RM 260.21
Rupees Two Hundred
Sixty and Paise Twenty
One Only
23419
Page 47 of 66
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.NoDSR Code
No_ 2013Description
Total
Qty.Unit Rate Rate In Words DSR-Amount
E. SUB HEAD - V - WATER SUPPLY, DRAINAGE PUMPS & EQUIPMENT
44
Providing two coats of Synthetic enamel paint of approved shade on
pipes and supports as per pipe colour code over a coat of primer.
Including painting of legends with direction arrow as per the approval of
the Consultants / Project Manager.
44.1 18.38.4 32 mm dia 30 RM 15.75Rupees Fifteen and Paise
Seventy Five Only 473
44.2 18.38.5 40 mm dia 45 RM 18.70Rupees Eighteen and
Paise Seventy Only 842
44.3 18.38.6 50 mm dia 50 RM 22.00Rupees Twenty Two and
Paise Zero Only 1100
Page 48 of 66
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.NoDSR Code
No_ 2013Description
Total
Qty.Unit Rate Rate In Words DSR-Amount
F. SUBHEAD - VI - ELECTRICAL
45
Supplying, laying, connecting, testing & commissiong of following sizes of
1.1 KV grade multicore aluminium conductor on the existing cabel tray /
surface as required PVC sheathed armoured cable as per IS 1554.
45.1 3 Core 4 Sqmm. (Aluminium) 150 Metre 225.00
Rupees Two Hundred
Twenty Five and Paise
Zero Only
33750
45.2 3 Core 6 Sqmm. (Aluminium) 150 Metre 255.00Rupees Two Hundred Fifty
Five and Paise Zero Only 38250
46 5.16Providing and fixing 6 SWG dia GI wire on surface or in recess for loop
earthing alongwith the existing cable as required.60 Metre 98.00
Rupees Ninety Eight and
Paise Zero Only 5880
47Supplying, installation, testing & commissiong of MS perforated & painted
cable tray duly suspended with hangers etc. as required.
47.1 4.1.2 150 x 50 x 1.6 mm 50 Mtr. 225.00
Rupees Two Hundred
Twenty Five and Paise
Zero Only
11250
47.2 4.1.1 100 x 50 x 1.6 mm 150 Mtr. 210.00Rupees Two Hundred Ten
and Paise Zero Only 31500
PLUMBING TOTAL 5023469
Page 49 of 66
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.NoDSR Code
No_ 2013Description
Total
Qty.Unit Rate Rate In Words DSR-Amount
SECTION - I - Point Wiring
1 1.3.3
Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5
sq.mm FR PVC insulated copper conductor single core cable in surface /
recessed steel conduit, with modular switch, modular plate, suitable GI box
and earthing the point with 1.5 sq.mm. FR PVC insulated copper conductor
single core cable etc as required.
1357 Point 1011.00
Rupees One Thousand
Eleven and Paise Zero
Only
1371927
2 1.5
Wiring for light / power plug with 2 x 4 sq. mm FR PVC insulated copper
conductor single core cable in surface / recessed steel conduit along with 1
No. 4 sq. mm FR PVC insulated copper conductor single core cable for
loop earthing as required.
3870 Metre 242.00
Rupees Two Hundred
Forty Two and Paise Zero
Only
936540
3 1.6
Wiring for light / power with 4 x 4 sq. mm FR PVC insulated coppeer
conductor single core cable in surface / recessed steel conduit along with 2
Nos. 4 sq. mm FR PVC insulated copper conductor single core cable for
loop earthing as required.
970 Metre 375.00
Rupees Three Hundred
Seventy Five and Paise
Zero Only
363750
4 1.7
Wiring for circuit / submain alongwith earth wire with the following sizes of
FR PVC insulated copper conductor, single core cable in surface /
recessed steel conduit as required.
4.1 1.7.1 2 x 1.5 sq. mm + 1 x 1.5 sq. mm earth wire 1350 Metre 183.00
Rupees One Hundred
Eighty Three and Paise
Zero Only
247050
4.2 1.7.2 2 x 2.5 sq. mm + 1 x 2.5 sq. mm earth wire 1850 Metre 207.00
Rupees Two Hundred
Seven and Paise Zero
Only
382950
5 1.24
Supplying and fixing following modular switch / socket on the existing
modular plate & switch box including connections but excluding modular
plate etc. as required.
5.1 1.24.6 Telephone socket outlet 93 Each 92.00Rupees Ninety Two and
Paise Zero Only 8556
6 1.27Supplying and fixing following size / modules, GI box along with modular
base & cover plate for modular switches in recess etc as required.
6.1 1.27 1 or 2 Module (75mm X 75mm) 93 Each 159.00Rupees One Hundred Fifty
Nine and Paise Zero Only 14787
ELECTRICAL WORKS
Page 50 of 66
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.NoDSR Code
No_ 2013Description
Total
Qty.Unit Rate Rate In Words DSR-Amount
7 1.28Supplying and fixing following Modular base & cover plate on existing
modular metal boxes etc. as required.
7.1 1.28.1 1 or 2 Module 93 Each 73.00Rupees Seventy Three
and Paise Zero Only 6789
8 1.18
Supplying and drawing following pair, 0.5 sq.mm FR PVC insulated copper
conductor, unarmoured telephone cable in the existing surface / recessed
steel / PVC conduit as required.
8.1 1.18.2 2 Pair 465 Metre 17.00Rupees Seventeen and
Paise Zero Only 7905
9 1.31
Supplying and fixing suitable size GI box with modular plate and cover in
front on surface or in recess, including providing and fixing 3 pin 5/6 amps
modular socket outlet and 5/6 amps modular switch, connection, painting
etc. as required.
236 Each 320.00
Rupees Three Hundred
Twenty and Paise Zero
Only
75520
10 1.32
Supplying and fixing suitable size GI box with modular plate and cover in
front on surface or in recess, including providing and fixing 6 pin 15/16
amps modular socket outlet and 15/16 amps modular switch, connection,
painting etc. as required.
321 Each 411.00
Rupees Four Hundred
Eleven and Paise Zero
Only
131931
11
1.27.4+
1.28.4+
1.24.4+ 1.24.1
Supplying and fixing suitable size GI box with modular plate and cover in
front on surface or in recess, including providing and fixing 2 Nos. 3 pin 5/6
amps modular socket outlet and 5/6 amps modular switch, connection,
painting etc. as required. UPS Point
84 Each 706.00Rupees Seven Hundred
Six and Paise Zero Only 59304
12 1.53
Supplying, laying, terminations, testing & commissioning of 4 pair UTP Cat -
6 PVC insulated ,PVC sheathed tinned copper conductor cable in existing
surface / recessed steel conduit as required.
1725 Metre 31.00Rupees Thirty One and
Paise Zero Only 53475
13 1.20
Supplying and fixing of following sizes of steel conduit along with
accessories in surface / recess including painting in case of surface
conduit, or cutting the wall and making good the same in case of recessed
conduit as required.
13.1 1.20.1 20 mm 550 Metre 131.00
Rupees One Hundred
Thirty One and Paise Zero
Only
72050
13.2 1.20.2 25 mm 900 Metre 152.00Rupees One Hundred Fifty
Two and Paise Zero Only 136800
Page 51 of 66
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.NoDSR Code
No_ 2013Description
Total
Qty.Unit Rate Rate In Words DSR-Amount
13.3 1.20.3 32 mm 100 Metre 203.00Rupees Two Hundred
Three and Paise Zero Only 20300
14 1.45
Installation, testing and commissioning of ceiling fan, including wiring the
down rods of standard length (upto 30 cm) with 1.5 sq. mm FR PVC
insulated, copper conductor, single core cable, including providing and
fixing phenolic laminated sheet cover on the fan box etc. as required.
5 Each 112.00
Rupees One Hundred
Twelve and Paise Zero
Only
560
15 1.25
Supplying and fixing stepped type electronic fan regulator on the existing
modular plate switch box including connections but excluding modular plate
etc. as required.
5 Each 362.00
Rupees Three Hundred
Sixty Two and Paise Zero
Only
1810
16 1.50.1
Installation of exhaust fan upto 450 mm sweep in the existing opening,
including making the hole to suit the size of the abiove fan, making good
the damage, connection, testing, commissioning etc. as required.
5 Each 189.00
Rupees One Hundred
Eighty Nine and Paise
Zero Only
945
17 1.51Extra for fixing the louvers/shutters complete with frame for a exhaust fan of
all sizes.4 Each 81.00
Rupees Eighty One and
Paise Zero Only 324
18 1.26Supplying and fixing modular blanking plate on the existing modular plate &
switch box excluding modular plate as required20 Each 23.00
Rupees Twenty Three and
Paise Zero Only 460
Sub Head - II -Distribution Board
19 2.8
Supplying and fixing following way, three pole and neutral, pre-wired, sheet
steel, MCB distribution board, 415 volts, on surface / recess, complete with
loose wire box, terminal blocks, duly prewired with suitable size FR PVC
insulated copper conductor upto terminal blocks, tinned copper busbar,
neutral link, earth bar , din bar, detachable gland plate, interconnections,
phophatized and powder painted including earthing etc. as required.
(but without MCB/RCCB/Isolator)
19.1 2.8.1 4 way (4+12), Double door 14 Each 6116.00
Rupees Six Thousand One
Hundred Sixteen and
Paise Zero Only
85624
19.2 2.8.2 6 way (4+18), Double door 5 Each 7887.00
Rupees Seven Thousand
Eight Hundred Eighty
Seven and Paise Zero
Only
39435
Page 52 of 66
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.NoDSR Code
No_ 2013Description
Total
Qty.Unit Rate Rate In Words DSR-Amount
19.3 2.8.3 8 way (4+24), Double door 9 Each 9024.00
Rupees Nine Thousand
Twenty Four and Paise
Zero Only
81216
19.4 2.8.4 12 way (4+36), Double door 1 Each 11082.00
Rupees Eleven Thousand
Eighty Two and Paise Zero
Only
11082
20 2.1
Supplying and fixing 5 amps to 32 amps rating, 240 volts, 'C' Series,
miniature circuit breaker suitable for inductive load of following poles in the
existing MCB DB complete with connections, testing and commissioning
etc. as required.
20.1 2.10.1 Single Pole 490 Each 146.00
Rupees One Hundred
Forty Six and Paise Zero
Only
71540
21
Supplying and fixing following rating, four pole, 415 volts, isolator in the
existing MCB DB complete with connections, testing and commissioning
etc. as required.
21.1 2.13.2 40 amps 12 Each 604.00Rupees Six Hundred Four
and Paise Zero Only 7248
21.2 2.13.2 63 amps 4 Each 614.00
Rupees Six Hundred
Fourteen and Paise Zero
Only
2456
22 2.14
Supplying and fixing following rating, double pole, (single phase and neutral
), 240 volts, residual current circuit breaker (RCCB), having a sensitivity
current upto 300 milliamperes in the existing MCB DB complete with
connections, testing and commissioning etc. as required.
22.1 2.14.1 25 amps 36 Each 1427.00
Rupees One Thousand
Four Hundred Twenty
Seven and Paise Zero
Only
51372
22.2 2.14.2 40 amps 36 Each 1510.00
Rupees One Thousand
Five Hundred Ten and
Paise Zero Only
54360
22.3 2.14.3 63 amps 12 Each 1974.00
Rupees One Thousand
Nine Hundred Seventy
Four and Paise Zero Only
23688
Page 53 of 66
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.NoDSR Code
No_ 2013Description
Total
Qty.Unit Rate Rate In Words DSR-Amount
23 2.11Supplying and fixing single pole blanking plate in the existing MCB DB
complete etc. as required.20 Each 6.00
Rupees Six and Paise
Zero Only 120
SUB HEAD - III - FIRE DETECTION WORK
24 1.20
Supplying and fixing of following sizes of steel conduit along with
accessories in surface / recess including painting in case of surface
conduit, or cutting the wall and making good the same in case of recessed
conduit as required.
24.1 1.20.1 20 mm 200 Metre 131.00
Rupees One Hundred
Thirty One and Paise Zero
Only
26200
24.2 1.20.2 25 mm 200 Metre 152.00Rupees One Hundred Fifty
Two and Paise Zero Only 30400
Page 54 of 66
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.NoDSR Code
No_ 2013Description
Total
Qty.Unit Rate Rate In Words DSR-Amount
SUB HEAD - IV - CABLE & CABLE TRAYS
SUPPLY AND LAYING OF CABLES / CABLE TRAYS / CABLE
TERMINATION
25 4.1
Fabricating and installing following size of perforated M.S. cable trays
including horizontal vertical bends,reducers ,tees,cross members and other
accessories as required and duly suspended from the ceiling with M.S.
suspenders and including painting with powder coating etc. as required.
25.1 4.1.8 300mm wide, 50mm high 2mm thick perforated type cable tray. 30 RM 841.00
Rupees Eight Hundred
Forty One and Paise Zero
Only
25230
25.2 4.1.2 150mm wide, 50mm high 2mm thick perforated type cable tray. 100 RM 523.00
Rupees Five Hundred
Twenty Three and Paise
Zero Only
52300
25.3 4.1.1 100mm wide, 50mm high 2mm thick perforated type cable tray. 100 RM 459.00
Rupees Four Hundred
Fifty Nine and Paise Zero
Only
45900
26 9.1
Supply and making end termination with brass compression glands for the
following PVC insulated XLPE / PVC sheathed 1.1KV grade cable including
cost of crimping lugs/ferrules, double compression glands, solder, cable
sockets, insulation tap etc complete as required.
26.1 9.1.23 3.5c x 70 sq. mm cable 8 Sets 324.00
Rupees Three Hundred
Twenty Four and Paise
Zero Only
2592
26.2 9.1.22 3.5c x 50 sq. mm cable 14 Sets 286.00
Rupees Two Hundred
Eighty Six and Paise Zero
Only
4004
26.3 9.1.34 4c x 25 sq. mm cable 18 Sets 211.00
Rupees Two Hundred
Eleven and Paise Zero
Only
3798
26.4 9.1.33 4c x 16 sq. mm cable 20 Sets 208.00Rupees Two Hundred
Eight and Paise Zero Only 4160
26.5 9.1.32 4c x 10 sq. mm cable 36 Sets 163.00
Rupees One Hundred
Sixty Three and Paise
Zero Only
5868
Page 55 of 66
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.NoDSR Code
No_ 2013Description
Total
Qty.Unit Rate Rate In Words DSR-Amount
SUB HEAD - V - CCTV SURVEILLANCE SYSTEM
27
Supplying and fixing of following sizes of steel conduit along with
accessories in surface / recess including painting in case of surface
conduit, or cutting the wall and making good the same in case of recessed
conduit etc. complete as required & approved by the Engineer In charge.
27.1 1.20.1 20 mm 200.00 Metre 131.00
Rupees One Hundred
Thirty One and Paise Zero
Only
26200
27.2 1.20.2 25 mm 250.00 Metre 152.00Rupees One Hundred Fifty
Two and Paise Zero Only 38000
27.3 1.20.3 32 mm 50.00 Metre 203.00Rupees Two Hundred
Three and Paise Zero Only 10150
Page 56 of 66
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.NoDSR Code
No_ 2013Description
Total
Qty.Unit Rate Rate In Words DSR-Amount
Sub Head -VI: Access Control System
A
Supply, installation, testing and commissioning of access control system
complete with all accessories, components, Graphical integrated Access
control management Software along with time & attendance to manage
required number of doors. required to make the system full functional and
consisting of the following equipments all as specified.
28
Supplying and fixing of following sizes of steel conduit along with the
accessories in surface / recess including painting in case of surface
conduit, or cutting the wall and making good the same in case of recessed
conduit as required.
28.1 1.20.2 25mm dia 400 Metre 152.00Rupees One Hundred Fifty
Two and Paise Zero Only 60800
Sub Head -VII: Integrated Building Management and Control System
A.
Supply, installation, testing and commissioning of the following equipment
forming part of the integrated building management system complete with
all accessories and components required for proper functioning of the
system all as specified.
29
Supplying and fixing of following sizes of steel conduit along with the
accessories in surface / recess including painting in case of surface
conduit, or cutting the wall and making good the same in case of recessed
conduit as required.
29.1 1.20.1 20mm dia 8000 Meter 131.00
Rupees One Hundred
Thirty One and Paise Zero
Only
1048000
29.2 1.20.2 25mm dia 2000 Meter 152.00 Rupees One Hundred Fifty
Two and Paise Zero Only 304000
ELECTRICAL INTERNAL TOTAL 6009476.00
Page 57 of 66
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.NoDSR Code
No_ 2013Description
Total
Qty.Unit Rate Rate In Words DSR-Amount
SUB HEAD - I - H.T. PANELS, TRANSFORMERS AND H.T. CABLES
End Termination (HT) :
30.
Supplying and making terminal joints for the following sizes of 11KV
Aluminium conductor XLPE cable including terminal lugs, insulation tape,
heat shrinkable kit complete as required.
30.1. 10.1.3 11KV, 3C x 240 sq. mm. XLPE Aluminium cable, indoor joints. 5 Nos. 3428.00
Rupees Three Thousand
Four Hundred Twenty
Eight and Paise Zero Only
17140
30.2. 10.2.3 11KV, 3C x 240 sq. mm. XLPE Aluminium cable, Outdoor joints. 1 Nos. 8156.00
Rupees Eight Thousand
One Hundred Fifty Six and
Paise Zero Only
8156
EXTERNAL ELECTRICAL
Page 58 of 66
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.NoDSR Code
No_ 2013Description
Total
Qty.Unit Rate Rate In Words DSR-Amount
SUB HEAD II - Cable, End Termination & Cable Trays
31 9.1
Supplying and making end termination with brass compression glands and
aluminium lugs for following size of PVC insulated and PVC sheathed/
XLPE aluminium conductor cable of 1.1 KV grade as required.
31.1 9.1.30 3½ x 300 Sqmm. 30 Set 940.00Rupees Nine Hundred
Forty and Paise Zero Only 28200
31.2 9.1.29 3½ x 240 Sqmm. 2 Set 824.00
Rupees Eight Hundred
Twenty Four and Paise
Zero Only
1648
31.3 9.1.27 3½ x 185 Sqmm. 16 Set 671.00
Rupees Six Hundred
Seventy One and Paise
Zero Only
10736
31.4 9.1.26 3½ x 150 Sqmm. 4 Set 501.00Rupees Five Hundred One
and Paise Zero Only 2004
31.5 9.1.25 3½ x 120 Sqmm. 12 Set 417.00
Rupees Four Hundred
Seventeen and Paise Zero
Only
5004
31.6 9.1.23 3½ x 70 Sqmm. 2 Set 324.00
Rupees Three Hundred
Twenty Four and Paise
Zero Only
648
31.7 9.1.22 3½ x 50 Sqmm. 10 Set 286.00
Rupees Two Hundred
Eighty Six and Paise Zero
Only
2860
31.8 9.1.21 3½ x 35 Sqmm. 2 Set 245.00
Rupees Two Hundred
Forty Five and Paise Zero
Only
490
ELECTRICAL EXTERNAL TOTAL 76886.00
Page 59 of 66
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.NoDSR Code
No_ 2013Description
Total
Qty.Unit Rate Rate In Words DSR-Amount
Sub Head - I (Motor Control Panels)
1
Providing and fixing 6 SWG dia. GI wire on surface or in recess for loop
earthing along with the existing surface / recessed conduits / submain
wiring / cable as required.
100 Mtrs. 22.00Rupees Twenty Two and
Paise Zero Only 2200.00
2Providing and fixing 25 x 5 mm G.I. Strip on surface or in recess for
connections etc. as required.120 Mtrs. 133.00
Rupees One Hundred
Thirty Three and Paise
Zero Only
15960.00
3
Supplying and making end termination with brass compression glands and
Al. lugs for following size of PVC insulated and PVC sheathed / XLPE Al.
conductor cable of 1.1 KV grade as required.
3.1 3 Core 10 Sqmm. 2 SET 136.00
Rupees One Hundred
Thirty Six and Paise Zero
Only
272.00
3.2 3 Core 50 Sqmm. 4 SET 241.00
Rupees Two Hundred
Forty One and Paise Zero
Only
964.00
FIRE FIGHTING TOTAL 19396.00
FIRE FIGHTING WORKS
Page 60 of 66
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.NoDSR Code
No_ 2013Description
Total
Qty.Unit Rate Rate In Words DSR-Amount
SUB HEAD 'I' CHILLED WATER PIPING WORKS
1 INSULATED CHILLED WATER PIPING
Supplying, laying/ fixing, testing and commissioning of following nominal
sizes of chilled water piping inside the building (with necessary clamos,
vibration isolators and fittings but excluding valves, strainers, gauges etc.)
duly insulated with 80 kg/cum density resin bonded fibre glass pipe section
insulation covered with a layer of 120 gm/sqm polythene sheet (vapour
barrier) and finally applying 0.63mm aluminium sheet cladding complete
with type3, grade I roofing felt strip (as per IS: 1322 as amended upto date)
at the joints repairing of damage to building etc. as per specifications and
as required.
The Pipes size 150mm & below shall be M.S. heavy class as per IS : 1239
and pipes size above 150mm shall be welded black steel pipe heavy class
as per IS: 3589, from minimum 6.35 mm thick M.S. Sheet for pipes upto
350 mm dia & from minimum 7mm thick M.S. sheet for pipes of 400 mm dia
& above.
1.1 16.1.6 150mm dia. (50mm insulation) 180.00 RMT 2793.00
Rupees Two Thousand
Seven Hundred Ninety
Three and Paise Zero Only
502740.00
1.2 16.1.7 125mm dia. (40mm insulation) 110.00 RMT 2272.00
Rupees Two Thousand
Two Hundred Seventy
Two and Paise Zero Only
249920.00
1.3 16.1.8 100mm dia. (40mm insulation) 90.00 RMT 1976.00
Rupees One Thousand
Nine Hundred Seventy Six
and Paise Zero Only
177840.00
1.4 16.1.9 80mm dia. (25 mm insulation) 80.00 RMT 1377.00
Rupees One Thousand
Three Hundred Seventy
Seven and Paise Zero
Only
110160.00
1.5 16.1.10 65mm dia. (25 mm insulation) 80.00 RMT 1187.00
Rupees One Thousand
One Hundred Eighty
Seven and Paise Zero
Only
94960.00
HVAC WORKS
Page 61 of 66
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.NoDSR Code
No_ 2013Description
Total
Qty.Unit Rate Rate In Words DSR-Amount
1.6 16.1.11 50mm dia. (25 mm insulation) 120.00 RMT 964.00
Rupees Nine Hundred
Sixty Four and Paise Zero
Only
115680.00
1.7 16.1.12 40mm dia. (25 mm insulation) 150.00 RMT 817.00
Rupees Eight Hundred
Seventeen and Paise Zero
Only
122550.00
1.8 16.1.13 32mm dia. (25 mm insulation) 120.00 RMT 704.00Rupees Seven Hundred
Four and Paise Zero Only 84480.00
1.9 16.1.14 25mm dia. (25mm insulation) 100.00 RMT 628.00
Rupees Six Hundred
Twenty Eight and Paise
Zero Only
62800.00
2BUTTERFLY VALVE (MANUAL) with C I body SS Disc, Nitrile Rubber Seal
& O- Ring PN 16 pressure rating for chilled water circulation as specified.
2.1 16.7.1.2 150mm dia. 4.00 Nos. 5977.00
Rupees Five Thousand
Nine Hundred Seventy
Seven and Paise Zero
Only
23908.00
2.2 16.7.1.3 125mm dia. 11.00 Nos. 5447.00
Rupees Five Thousand
Four Hundred Forty Seven
and Paise Zero Only
59917.00
2.3 16.7.1.4 100mm dia. 2.00 Nos. 4563.00
Rupees Four Thousand
Five Hundred Sixty Three
and Paise Zero Only
9126.00
2.4 16.7.1.5 80mm dia. 4.00 Nos. 3514.00
Rupees Three Thousand
Five Hundred Fourteen
and Paise Zero Only
14056.00
2.5 16.7.1.6 65mm dia. 2.00 Nos. 3151.00
Rupees Three Thousand
One Hundred Fifty One
and Paise Zero Only
6302.00
2.6 16.7.1.7 50mm dia. 16.00 Nos. 2753.00
Rupees Two Thousand
Seven Hundred Fifty Three
and Paise Zero Only
44048.00
Page 62 of 66
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.NoDSR Code
No_ 2013Description
Total
Qty.Unit Rate Rate In Words DSR-Amount
3
BALANCING VALVE WITH BUILT IN MEASURING FACILITY with C I
body flanged construction with EPDM coated disc with long pitch with
protruded out pipe insulation & PN 16 pressure rating for chilled water
circulation as specified.
3.1 16.7.2.3 125mm dia. 4.00 Nos. 18608.00
Rupees Eighteen
Thousand Six Hundred
Eight and Paise Zero Only
74432.00
3.2 16.7.2.4 100mm dia. 1.00 Nos. 13626.00
Rupees Thirteen
Thousand Six Hundred
Twenty Six and Paise Zero
Only
13626.00
3.3 16.7.2.5 80mm dia. 2.00 Nos. 7497.00
Rupees Seven Thousand
Four Hundred Ninety
Seven and Paise Zero
Only
14994.00
3.4 16.7.2.6 65mm dia. 1.00 Nos. 6209.00
Rupees Six Thousand Two
Hundred Nine and Paise
Zero Only
6209.00
3.5 16.7.2.7 50mm dia. 1.00 Nos. 4865.00
Rupees Four Thousand
Eight Hundred Sixty Five
and Paise Zero Only
4865.00
4
NON - RETURN VALVE with duel plate of C I body SS plates vulcanized
NBR seal flanged end & PN 16 pressure rating for chilled water circulation
including insulation as specified.
4.1 16.7.3.2 150mm dia. 2.00 Nos. 7217.00
Rupees Seven Thousand
Two Hundred Seventeen
and Paise Zero Only
14434.00
4.2 16.7.3.3 125mm dia. 3.00 Nos. 5583.00
Rupees Five Thousand
Five Hundred Eighty Three
and Paise Zero Only
16749.00
5Y - STRAINER of Ductile CI Body flanged ends with stainless steel strainer
for chilled water circulation including insulation as specified.
Page 63 of 66
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.NoDSR Code
No_ 2013Description
Total
Qty.Unit Rate Rate In Words DSR-Amount
5.1 16.7.4.2 150mm dia. 2.00 Nos. 14884.00
Rupees Fourteen
Thousand Eight Hundred
Eighty Four and Paise
Zero Only
29768.00
5.2 16.7.4.3 125mm dia. 3.00 Nos. 9880.00
Rupees Nine Thousand
Eight Hundred Eighty and
Paise Zero Only
29640.00
5.3 16.7.4.7 50mm dia. 7.00 Nos. 4373.00
Rupees Four Thousand
Three Hundred Seventy
Three and Paise Zero Only
30611.00
6 16.8 Dial type pressure gauges with gun metal valves etc. as required. 16.00 Nos. 947.00
Rupees Nine Hundred
Forty Seven and Paise
Zero Only
15152.00
7 16.9 Industrial type thermometers. 6.00 Nos. 673.00
Rupees Six Hundred
Seventy Three and Paise
Zero Only
4038.00
SUB HEAD 'II' AIR DISTRIBUTION WORKS
8
Supply, installation, balancing and commissioning of Factory fabricated
GSS sheet metal (conforming to IS:277-1962 (revised)) rectangular
ducting as per BIS (IS : 655) standard complete with neoprene rubber
gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per
approved drawings and specifications of following gauges:-
8.1 16.12.1.1 24 Gauge ( Thickness 0.63mm) 1500.00 Sqm. 637.00
Rupees Six Hundred Thirty
Seven and Paise Zero
Only
955500.00
8.2 16.12.1.2 22 Gauge (Thickness 0.8mm) 350.00 Sqm. 750.00Rupees Seven Hundred
Fifty and Paise Zero Only 262500.00
8.3 16.12.1.3 20 Gauge (Thickness 1.0mm) 30.00 Sqm. 933.00
Rupees Nine Hundred
Thirty Three and Paise
Zero Only
27990.00
8.4 16.12.1.4 18 Gauge (Thickness 1.25mm) 20.00 Sqm. 1069.00
Rupees One Thousand
Sixty Nine and Paise Zero
Only
21380.00
Page 64 of 66
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.NoDSR Code
No_ 2013Description
Total
Qty.Unit Rate Rate In Words DSR-Amount
9
Supply, fixing and commissioning of powder coated extruded aluminum
diffusers complete with black anodized extruded aluminum VCD, nuts,
bolts, screws etc. as per approved drawings and specifications.
9.1 16.17 Supply air diffusers with volume control damper. 13.00 Sqm. 3742.00
Rupees Three Thousand
Seven Hundred Forty Two
and Paise Zero Only
48646.00
9.2 16.18 Return air diffusers without volume control damper 13.50 Sqm. 5621.00
Rupees Five Thousand Six
Hundred Twenty One and
Paise Zero Only
75883.50
10 16.13
Supply, installation, testing and commissioning of GI volume control duct
damper complete with neoprene rubber gaskets, nuts, bolts, screws
linkages, flanges etc, as per specifications.
7.00 Sqm. 4673.00
Rupees Four Thousand
Six Hundred Seventy
Three and Paise Zero Only
32711.00
11 16.14
Supply, installation, testing and commissioning of Motorized (ON-OFF type
) GI volume control dampers with enthalpy sensor & necessary control
wiring complete with neoprene rubber gaskets, nuts, bolts, screws
linkages, flanges & nesessary control wiring etc, as per specifications.
11.1 16.14.1 Damper 3.00 Sqm. 5355.00
Rupees Five Thousand
Three Hundred Fifty Five
and Paise Zero Only
16065.00
11.2 16.14.2 Actuator 15.00 Nos. 5230.00
Rupees Five Thousand
Two Hundred Thirty and
Paise Zero Only
78450.00
12 16.20
Supplying, installation, testing and commissioning of fire dampers, the
blades and frame shall be min. 1.6 mm thick GI sheet and factory fitted in a
sleeve made out of 1.6 mm thick GS Sheet of min. 400 mm long, as &
where required, of required sizes including control wiring. The damper shall
be motorized and spring return so as to close the damper in the event of
power failure automatically and open the same in case of power being
restored. The spring return action shall be inbuilt mechanism and not
externally mounted. The damper shall also be closed in the event of fire
signal. CBRI tested and certified for 60 minute fire rating etc. complete as
required and as per specifications.
12.1 16.20.1 Fire damper 5.00 Sqm. 6864.00
Rupees Six Thousand
Eight Hundred Sixty Four
and Paise Zero Only
34320.00
12.2 16.20.2 Actuator 25.00 Nos. 6517.00
Rupees Six Thousand Five
Hundred Seventeen and
Paise Zero Only
162925.00
Page 65 of 66
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.NoDSR Code
No_ 2013Description
Total
Qty.Unit Rate Rate In Words DSR-Amount
SUB HEAD 'III' - ELECTRICAL WORKS
13
Supplying and making end termination with brass compression glands and
Al. lugs for following size of PVC insulated and PVC sheathed / XLPE Al.
conductor cable of 1.1 KV grade as required.
13.1 9.1.7 3 Core 10 Sqmm. 10.00 Set 136.00
Rupees One Hundred
Thirty Six and Paise Zero
Only
1360.00
13.2 9.1.8 3 Core 16 Sqmm. 2.00 Set 162.00
Rupees One Hundred
Sixty Two and Paise Zero
Only
324.00
13.3 9.1.32 4 Core 10 Sqmm. 4.00 Set 163.00
Rupees One Hundred
Sixty Three and Paise
Zero Only
652.00
13.4 9.1.33 4 Core 16 Sqmm. 4.00 Set 208.00Rupees Two Hundred
Eight and Paise Zero Only 832.00
13.5 9.1.20 3.5 Core 25 Sqmm. 2.00 Set 210.00Rupees Two Hundred Ten
and Paise Zero Only 420.00
13.6 9.1.21 3.5 Core 35 Sqmm. 4.00 Set 245.00
Rupees Two Hundred
Forty Five and Paise Zero
Only
980.00
14 5.4
Earthing with GI earth plate 600 mm x 600 mm x 6 mm thick including
accessories, and providing masonary enclosure with cover plate having
locking arrangement and watering pipe of 2.7 metre long etc. with charcoal
/ coke and salt as required.
4.00 Set 4367.00
Rupees Four Thousand
Three Hundred Sixty
Seven and Paise Zero
Only
17468.00
15 5.18
Providing and fixing 6 SWG dia. GI wire on surface or in recess for loop
earthing along with the existing surface / recessed conduits / submain
wiring / cable as required.
500.00 Mtrs. 22.00Rupees Twenty Two and
Paise Zero Only 11000.00
16 5.15Providing and fixing 25 x 5 mm G.I. Strip on surface or in recess for
connections etc. as required.100.00 Mtrs. 133.00
Rupees One Hundred
Thirty Three and Paise
Zero Only
13300.00
17 5.11
Providing and fixing 25 x 5 mm G.I. Strip in 40 mm dia. G.I. pipe from earth
electrode including connection with G.I. nut, bolt, spring, washer excavation
and re-filling etc. as required.
80.00 Mtrs. 391.00
Rupees Three Hundred
Ninety One and Paise
Zero Only
31280.00
HVAC TOTAL 3726991.50
Page 66 of 66
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.No DescriptionTotal
Qty.Unit Rate Rate In Words MR-Amount
1 Sub Head-I WALL CLADDING
1.1 Providing & fixing of Luxalon aluminium extruded Aerofoil AF - 350 Sun
Louvers. The panels shall be 350 MM wide, 56 MM high in desired length upto a
maximum length of 3500 MM. the panels shall be made out of 1.8 MM thick
aluminium extrusion in Anodized / PVDF/ Mill Finish. The panels shall be
installed horizontally or vertically to the frame in a fixed angle by means of
aluminium sliding U profile, & fixation disc & fin suspension made out of fiber
allowing it to lock at fixed degree in increments of 5 degrees from 0 to 180
degree. The fixation disc is clicked into position by sliding the U-profile section
over the fin suspension. The ends of the panels shall be covered by aluminium
plates having thickness 1.5 MM the panels shall be installed in a module of 335
MM giving an overlap of 15 MM.
1481 metre
1.2 Providing & fixing Zinc Composite panel wall cladding system comprising of top
Layer 4 mm thick Zinc LDPE panels of 990 mm X 3000 mm size made with 0.5
mm QUARTZ Zinc (VM ZINC) & Aluminium skins 0.5 mm each. Alloy type -
3105, Core Material - LDPE. Virgin Core Thickness - 3 mm (to to installed by
agency approved by manufacturer). Galvonized GI Substructure of 25 mm X 50
mm metal frames along with necessary brackets / cleat / screws for fixing of
ZCP panels on the Metal Substructure as per instructions etc and all
precautions to be taken to avoid bimetaalic corrosion complete as per design.
(Basic rate=Rs 400 per sq.ft)
1316 sqm
2 Sub Head II WOOD AND PVC WORK
2.1 Providing and fixing 12 mm thick frameless toughened glass door partitions of
approved brand and manufacturer, including providing and fixing partitions at
top & bottom with aluminum channel etc. all complete as per direction of
Engineer-in-charge
1136 sqm
2.2 Providing and fixing approved brand and manufacturer SS 304 grade
hardware's for Doors etc.
a ) Providing and fixing approved brand and manufacturer SS 304 grade S.S Floor
door spring fixed with SS screws etc. complete in all respects as per
manufacturer's specifications & as directed by Engineer-in-charge.
34 nos
b ) Providing and fixing approved brand and manufacturer SS 304 grade S.S
Handles including lock (1200 mm) fixed with SS screws etc. complete in all
respects as per manufacturers' specifications & as directed by Engineer-in-
charge.
92 nos
CIVIL WORK
Page 1 of 119
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.No DescriptionTotal
Qty.Unit Rate Rate In Words MR-Amount
c ) Providing and fixing approved brand and manufacturer SS 304 grade S.S
Handles (450 mm) fixed with SS screws etc. complete in all respects as per
manufacturers' specifications & as directed by Engineer-in-charge.
224 nos
d ) Providing and fixing approved brand and manufacturer SS 304 grade S.S door
stopper fixed with SS screws etc. complete in all respects as per manufacturer's
specifications & as directed by Engineer-in-charge.
135 nos
e ) Providing and fixing approved brand and manufacturer SS 304 grade S.S dead
lock fixed with SS screws etc. complete in all respects as per manufacturer's
specifications & as directed by Engineer-in-charge.
112 nos
f ) Providing and fixing approved brand and manufacturer SS 304 grade S.S tower
bolt (300mm) fixed with SS screws etc. complete in all respects as per
manufacturer's specifications & as directed by Engineer-in-charge.
135 nos
g ) Providing and fixing approved brand and manufacturer SS 304 grade S.S tower
bolt (150mm) fixed with SS screws etc. complete in all respects as per
manufacturer's specifications & as directed by Engineer-in-charge.
135 nos
h ) Providing and fixing approved brand and manufacturer SS 304 grade patch
fittings L type for frameless doors fixed with SS screws etc. complete in all
respects as per manufacturer's specifications & as directed by Engineer-in-
charge.
270 Sets
3.0 Sub Head III FLOORING
3.1 Providing and laying Laminate wooden flooring (Grade AC4, 8 mm thick
Ambience Premium-AC4 ), having a good backing layer made up of plastic
laminate or melamine as specified by the manufacturer and approved by
Engineer-in-charge.
a) Flooring 156 sqm
b) Skirting 16 sqm
c) Floor strip on edges 180 metre
3.2 Providing & laying Granite stone flooring with 18mm thick granite stone of
approved colour and shade over 20mm(average) thick base of cement mortar
1:4 (1 cement :4 coarse sand) laid with joints treated with colour pigment at all
heights.(sample of granite shall be approved by Engineer – In – Charge; basic
rate of granite stone considered as per DAR-2013)
1970.79 sqm
3.3 Extra for pre finished nosing to treads of steps of Granite stone. 480 metre
3.4 Extra for Granite stone flooring in treads of steps and risers using single length
up to 2.00 metre .144 sqm
3.5 Providing and fixing 18mm thick Granite stone work for wall lining at all height in
cement mortar 1:3 (1cement : 3 coarse sand) including pointing with white
cement mortor with an admixture of pigment to match the granite shade
complete as per direction of Engineer-in-charge.
1500 sqm
Page 2 of 119
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.No DescriptionTotal
Qty.Unit Rate Rate In Words MR-Amount
3.6 Providing and fixing PVC sheet flooring in 2.0mm thickness. It shall be
homogeneous and monolayer in construction, and shall be manufactured by
calendering and presssing, to ensure a dense, smooth surface and non-
directional design. The flooring shall incorporate a specially formulated
polyurethane reinforcement, to significantly reduce maintenance costs.
[Equivalent to Polyfloor Mystique PUR]
1809 sqm
3.7 Providing and applying 1mm thk Vinyl based Anti-microbial wall covering over
smooth surface including fixing with adhesive complete as per drawing & as
directed by Engineer-in-charge.
415 sqm
4 Sub Head IV ROOFING
4.1 Providing & fixing trap door in the false ceiling using 19 mm thk commercial ply
laminated with approved finish 1mm thick laminate with necessary 2nd Class
teak frame work of size 2" x 1.5", Oak wood mouldings as per Architect’s
drawing, brass hinges, latches etc. complete in all respect as directed by
Engineer-in-charge.
371 sqm
4.2 Providing and making 75mm deep suspended feature panel ceiling comprising
of 19mm Thk. Commercial Board layered with 4mm Thk. Italian Veneer ply
including all edge mouldings, melamine polish, suspension system etc.
complete as per drawing & as directed by Engineer-in-charge.
222 sqm
5 Sub Head V ALUMINIUM WORK
5.1 Providing and fixing over glass 1.5mm thick Etching strips (film) of approved
make fixed as per manufacturer's specifications all complete as per direction of
the Engineer-in-charge.
1467 sqm
5.2 Providing, fabricating and fixing 12 mm thick Acrylic based solid stone veneering
of approved make including cost of fabrication, fusion, edges, hole cutting for
fixtures complete in dado over 12mm thick BWP ply fixed on aluminum frame
work a maximum spacing of 600mm in any one direction (including adding
members as required) as approved by Engineer-in-charge/ Architect including
cutting chase in wall where ever required etc complete as per drawings.
(Aluminum frame shall be paid seprately) (Basic rate of stone Rs 9419 per
sq.m.)
49 sqm
Page 3 of 119
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.No DescriptionTotal
Qty.Unit Rate Rate In Words MR-Amount
5.3 Providing & fixing of 75mm thick 2800mm height partition system comprising of
MS Box section Sub frame as horizontol & vertical members of size
50mmx50mmx1.626mm. The module shall not be more than 500mm in height &
1000mm in length and bottom module shall at 85mm from skirting. the frame
shall be connected at the junctions by welding. the sub frame shall be fixed to
wall, floor and ceiling with dash fastners / and extending M.S.frameworkas
required. this includes cost of PVC Gaskets, foam, levellers,trims, cable carrier
for LV & MV cables,and both side 12mm thk. prelaminated particle board of
approved shade fixed to sub frame with MS cleats and SS fixing arrangement as
approved. all metallic parts shall be treated with anti rust treatment & painted
with 2 coats of enamel paint in redoxide primer. Hardware shall be conforming
to BIFMA/ANSI standards as approved by Architect and Engineer.
1540 sqm
5.4 Providing & fixing of 75mm thick 1500mm height dado comprising of MS Box
section Sub frame as horizontol & vertical mambers of size
50mmx50mmx1.626mm. The module shall not be more than 500mm in height &
1000mm in length and bottom module shall at 85mm from skirting. the frame
shall be connected at the junctions by welding. the sub frame shall be fixed to
wall, floor and ceiling with dash fastners as required. this includes cost of PVC
Gaskets, foam, levellers,trims, cable carrier for LV & MV cables,and single side
12mm thk. prelaminated particle board of approved shade fixed to sub frame
with MS cleats and SS fixing arrangement as approved. all metallic parts shall
be treated with anti rust treatment & painted with 2 coats of enamel paint in
redoxide primer. Hardware shall be conforming to BIFMA/ANSI standards as
approved by Architect and Engineer.
250 sqm
Page 4 of 119
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.No DescriptionTotal
Qty.Unit Rate Rate In Words MR-Amount
6 SUB HEAD - VI - WATER PROOFING WORK
6.1 Providing and laying foam concrete filling in sunken portion of W.C. & kitchen
with approved quality of cinder including supply of labour, material, and tools
and plant etc. required for proper completion of the work as per direction of
Engineer-in-charge.
55 cum
6.2 Terrace Garden Water proofing
a ) Supplying and applying a 1.5mm thick non reinforced EPDM membrane
conforming to ASTM D6134-97 on given newly laid cement sand mortar
substrate with the help of appropriate recommended blinded adhesive as per
manufacturer recommendations keep 100mm overlap between two adjacent
membrane and adhere it with appropriate splice adhesive.
764 sqm
b ) Providing and laying protection layer with specify geotextile membrane with
minimum 250gsm weight and application as per manufacturer specification. 764 sqm
c ) Providing and applying average 35mm thick (or as specified) cement sand
mortar in with ratio of 1:3 modified with admixture on geotextile membrane to
provide suitable or as specified slope for easy water disposal
764 sqm
d ) However the further work will followed by laying primer root barrier, insulation,
drainage boards, aeration, water storage and secondary root barrier above this
growing medium and vegetation will be follow.
764 sqm
7 Sub Head VII MISCELLANEOUS WORK
7.1 P/F S.S. Chair rail 250 x 50mm fixed to wall at intermediate distances including
fixing arrangement, finishing with duco paint complete114 metre
Page 5 of 119
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.No DescriptionTotal
Qty.Unit Rate Rate In Words MR-Amount
8 Sub Head VIII HORTICULTURE & LANDSCAPING
8.1 Supply & Planting best quality trees inclusive of cultivation of trees bead
to required depth. All trees / plants to be approved before planting
including watering & maintenance for 180 days.
A Treesi ) Alstonia Scholaris 'Milky pine' (1500-1800mm high) 2 eachii ) Hibiscus Mutabilis-Chaneable Rose'confederate Rose' 2 eachiii ) Grevillea Robusta 'Silky Oak' 2 eachiv ) Bombax Ceiba ' Silky-Cotton Tree' 2 eachv ) Furcraea gigantea ' mauritius hemp' 2 eachvi ) Michelia Champaca 'Golden Champa' 2 eachvii ) Melia azedarach ' Chinaberry' 2 eachviii ) Albizia Procera 2 eachix ) Couroupita Guianensis 2 eachx ) Kagelia Pinnata 2 each
B Shrubs i ) Calliandra Haematocephala ' White Powderpuff' 5 eachii ) Rhapis Excelsa ' Broadleaf Lady Palm Or Bamboo Palm' 5 eachiii ) Gardenia Jasminoides ' Cape-jasmine' 5 eachiv ) Russelia Equisetiformis 'Fire Cracker plant' 5 sqmv ) Ixora Chinensis 'dwarf Rangan' 5 sqmvi ) Putranjiva Roxburghii 'Lucky Bean Tree' 5 sqm
C Ground Coveri ) Wedelia Trilobata 'Yellow Dot' 298 sqmii ) Iresine Herbstii ' Blood Leaf Plant' 298 sqmiii ) Cynodon dactylon ' Calcutta Grass' 298 sqmiv ) paspalum Vaginatum 'paspalum Grass' 298 sqmv ) Jasminum pubescenes 'rubescens' 298 sqm
9 Sub Head IX ROAD WORKS :
9.1 Providing placing & fixing Precast Concrete Grass Grid Pavers of 70 mm
Thickness and appropriate size, laid over compacted earth and over 75 mm
thick layer (average) of Jamuna sand, manufactured by using M-30 grade of
concrete by using vibro compaction process using accurately designed moulds.
The Grass Grid pavers shall be suitably reinforced etc. complete in all respects
as per direction of the Engineer-in-charge.
494 sqm
9.2 Providing & fixing Rubberised corner guard in Stilt to protect from Vehicular
demage 819 sqm
CIVIL TOTAL
Page 6 of 119
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.No DescriptionTotal
Qty.Unit Rate Rate In Words MR-Amount
A. INTERNAL PLUMBING WORK
SUB HEAD - I - SANITARY FIXTURES
1 Providing and fixing, testing & commissioning of CP brass angle valve with
ABS Health Faucet (complete with hook and flexible SS tube min. Length
1.0 m) as required.
32 Each
2 Providing and fixing white vitreous china Oval wash basin with CI/MS
brackets painted white, 15 mm CP brass pillar taps, 32 mm CP brass waste
of standard pattern, including painting of fittings and brackets cutting and
making good the walls wherever required.
2.1 wall mounted wash basin size 560 x 410 mm with centre tap hole, single 15
mm CP brass pillar tap52 Each
3 Providing and fixing white vitreous china rectangular over /below counter
Wash Basin with CI/MS brackets painted white, 15 mm CP brass pillar taps,
32 mm CP brass waste of standard pattern, including painting of fittings and
brackets cutting and making good the walls wherever required.
3.1 below counter wash basin size 750 x 480 mm with centre tap hole, single 15
mm CP brass pillar tap12 Each
4 Providing, fixing, testing and commissioning of Ivory vitreous china large flat
back battery operated urinal with built in automatic sensor based flushing
system. All other details as per item described above. (Hindware, SENSO,
Cat. No.: 60007)
14 Each
5 Providing & Fixing white glazed vitreous china urinal partitions of approved
make including rawl plugs, screws or any other approved device for fixing
arrangements, making holes in walls, floors & making good.(Hindware,
SENSO, Cat. No.: 61005)
7 Each
6 Providing, fixing, testing and commissioning of C.P. brass single hole sink
mixer with CP wall flange, swinging spout complete as required and
making good.
6 Each
7 Providing and fixing adjustable type wash basin for handicap toilet
complete with brackets, tracks (Model R4140), waste pipes and other
accessories complete as required. (Make : Presalit - Commander)5 Each
PLUMBING WORK
Page 7 of 119
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.No DescriptionTotal
Qty.Unit Rate Rate In Words MR-Amount
8 Providing and fixing 2 Nos. support arms and backrest to mounted on the
track (vertically and laterally) Model R3548 & 6533) for handicap toilet
complete as required. (Make : Presalit - Commander)5 Each
9 Providing and fixing raised toilet seat with cover for handicap toilet (Make
: Presalit - Commander, R-35000)5 Each
10 Providing and fixing powder coated steel grab bar. (Make : Commander -
RT100)5 Each
11 Providing and fixing CP brass twin coat hooks fixed on toilet door/wall with
CP brass screws. 32 Each
12 Providing, fixing, testing and commissioning of two way C.P. brass bib
cock with C.P. wall flange of approved quality32 Each
13 Providing, fixing, testing and commissioning of C.P Copper connection
450 mm long including nuts and washers and making connection to fixtures
and fittings complete as required.
96 Each
Page 8 of 119
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.No DescriptionTotal
Qty.Unit Rate Rate In Words MR-Amount
SUB HEAD - II - SOIL, WASTE AND VENT PIPES, RAIN WATER PIPES
14 Providing and fixing soil, waste and vent pipes.
14.1 150 mm dia pipe as per IS:3989 10 Each
15 Providing and fixing heel rest sanitary bend.
15.1 150 mm 0 Each
16 Providing and fixing single unequal plain junction of required degree.
16.1 150 x 150 x 75 mm 0 Each
16.2 150 x 150 x 100 mm 0 Each
17 Providing, fixing and jointing UV stabilized uPVC rain water pipes
conforming to IS:4985 (working pressure 6 kg/sqcm.) including all fittings
such as bends, clamps, tees, cowls, clean out plugs etc including Fixing at
wall / ceiling level supported by steel clamps & hangers etc. including
Cutting, chases/holes in floors / walls / slab and making good the same after
pipe have been duly laid and testing complete in all respects.
17.1 200 mm diameter 0 Metre
17.2 160 mm diameter 510 Metre
17.3 110 mm diameter Metre
18 Providing and fixing on wall face/Concealed unplasticised - PVC moulded
fittings/accessories for unplasticised rigid PVC rain water pipes conforming
to IS:4985 including jointing with seal ring confirming to IS:5382 leaving 10
mm gap for thermal expansion.
18.1 160x160x160 mm 19 Each
18.2 160 mm bend 19 Each
20 Providing and fixing G.I. pipes complete with G.I. fittings including painting,
jointing, testing the cost of cutting the chases and making good the same for
waste water disposal complete as per direction of engineer incharge.
20.1 32 mm dia nominal bore (Wash basin to floor trap/floor drain) 0 Metre
20.2 40 mm dia nominal bore (wash basin to floor trap) 100 Metre
20.3 50 mm dia nominal bore (urinal to Floor Trap) 98 Metre
Page 9 of 119
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.No DescriptionTotal
Qty.Unit Rate Rate In Words MR-Amount
21 Providing and fixing C.P. brass bottle trap including CP waste fittings
complete in all respect of approved quality.
21.1 32mm dia 84 Each
22 Providing and fixing cleaning eye on horizontal CI soil & waste pipes of 300
mm long GI medium class pipe with one plain end lead caulked in to the
collar of CI pipe and the other end with flange which in covered by neoprene
rubber gasket and blank flange, complete with nuts, bolts etc and hot dip
galvanization after fabrication to the satisfaction of Engineer in Charge
22.1 100 mm dia 44 Each
22.2 150 mm dia 0 Each
23 Providing and fixing G.I. EXTENSION PIECE for 75 mm dia floor trap
formed out of main pipe (Type A) with multiple side inlets, suitable for
various dia pipes, side connections, including all fixtures and fittings as per
site conditions and as per standard details and water tight sealing of joints
and area surrounding the grating and as directed.
Each
24 Providing and fixing G.I EXTENSION PIECE for 100 mm dia floor trap
formed out of main pipe (Type A) with multiple side inlets, suitable for
various dia pipes, side connections, including all fixtures and fittings as per
site conditions and as per standard details and water tight sealing of joints
and area surrounding the grating and as directed.
72 Each
25 Providing and fixing cleaning eye on horizontal PVC rain water pipes
comprising of PVC socket caulked to pipe with one plain end solvent
caulked in to the collar of pipe and the other end with flange and pvc plug
with suitable inlet key for opening male threaded joint with PVC pipe &
socket. Including solvent caulked to PVC pipes complete as required.
25.1 For 110 mm dia pipe Each
25.2 For 160 mm dia pipe 0 Each
26 Providing and fixing P.V.C. WC connector (straight or bend type) with
rubber lip ring. Including 110 mm dia PVC pipe / bend of required length
and proper connection with M seal to C.I. pipe complete as required 32 Nos.
Page 10 of 119
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.No DescriptionTotal
Qty.Unit Rate Rate In Words MR-Amount
SUB HEAD - III - WATER SUPPLY
27 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having
thermal stability for hot & cold water supply including all CPVC plain & brass
threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This
includes jointing of pipes & fittings with one step CPVC solvent cement and
the cost of cutting chases and making good the same including testing of
joints complete as per direction of Engineer in Charge.
Concealed work including cutting chases and making good the walls etc.
27.1 40 mm nominal outer dia pipes (SDR-11) 18 Metre
27.2 50 mm nominal outer dia pipes (SDR-11) 0 Metre
28 Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c
cutting and making good the walls etc. (Internal work):
Exposed on Wall
28.1 65 mm dia nominal bore 80 Metre
28.2 80 mm dia nominal bore 50 Metre
28.3 100 mm dia nominal bore 0 Metre
29 Providing and fixing Nitrile Rubber Insulation 9 mm thick on hot water
supply/return pipes without outer mechanical protection
29.1 15 mm dia. 384 Metre
29.2 20 mm dia. 160 Metre
29.3 25 mm dia. 56 Metre
30 Providing and fixing Nitrile Rubber Insulation 9 mm thick on hot water
supply/return pipes with outer mechanical protection
30.1 15 mm dia. 15 Metre
30.2 20 mm dia. 50 Metre
30.3 25 mm dia. 95 Metre
30.4 32 mm dia. 100 Metre
30.5 40 mm dia. 45 Metre
Page 11 of 119
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.No DescriptionTotal
Qty.Unit Rate Rate In Words MR-Amount
31 Providing & fixing full way lever operated forged brass ball valve of brass
body with forged brass hard chrome plated steel ball tested to a pressure
not less than 10 Kg / sqcm with threaded / flanged joints complete with nuts,
bolts, gaskets, washers etc.
31.1 15 mm diameter 6 Each
31.2 20 mm diameter 10 Each
32 Providing and fixing Butter fly valve with nitrile seat and stainless steel stem
with lever operation and cast iron body in powder coated finish, suitable for
test pressure of 10Kg/sq.mm) with flanges, gaskets and necessary pad
locking arrangement complete required.
32.1 65 mm dia. 1 Each
32.2 80 mm dia. 1 Each
32.3 100 mm dia. 1 Each
33 Providing and fixing full way lever operated forged brass ball valve of brass
body with forged brass hard chrome plated steel ball, union / flange, washer,
nuts & bolt. Rated to temperature of 85 deg. C and testing to a pressure not
less than 10 Kg/sq.cm including covering with nitrle rubber insulation 9 mm
thick insulation as per specification.
33.1 15 mm dia. 10 Each
33.2 20 mm dia. 4 Each
33.3 25 mm dia. 6 Each
33.4 32 mm dia. 2 Each
33.5 40 mm dia. 0 Each
33.6 50 mm dia. 1 Each
33.7 65 mm dia. 1 Each
33.8 80 mm dia. 1 Each
Page 12 of 119
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.No DescriptionTotal
Qty.Unit Rate Rate In Words MR-Amount
SUB HEAD - IV - SEWERAGE & DRAINAGE
34 Material & labour for constructing R.C.C. Grease trap of size 2200mm x
1500mm x 2500mm deep with RCC walls with inlet & outlet including
necessary excavation and foundation concrete 100mm thick in 1:5:10 (1
cement : 5 coarse sand : 10 graded stone aggregate of 40mm nominal
size), inside plaster 12mm thick in cement mortar 1:4 (1 cement : 4 coarse
sand) finished with a floating coat of neat cement, RCC base slab, roof slab
& baffle walls including reinforcement, centring & shuttering including 12mm
dia steel bar footrests etc. and SFRC manhole cover and frame of 600mm x
450mm internal dimension conforming to IS: 12592 (total weight of cover
& frame shall not be less than 70 kg)
1 Each
E. SUB HEAD - V - WATER SUPPLY, DRAINAGE PUMPS & EQUIPMENT
35 PUMPS
Supply, assembly, erection, testing and commissioning of pumping system
comprising the following:
Vertical/ Horizontal centrifugal pumps (1 Working + 1 Stand-by) with
mechanical seal, SS Volute casing and SS impeller connected to suitable
capacity TEFC induction motor suitable for 415 ± 10 % volts, 3 phase, 50
cycles A.C. supply with 100 mm dia. pressure gauges including MS skid
and mounting of the pumps on the skid. (Motor to be of the same make as
the pump)35.1 Pump Capacity 135 lpm, at 35 m head (1 Working + 1 Stand-by) FILTER
FEED PUMPS (for Dom. Use)1 Set
35.2 Pump Capacity 200 lpm, at 35 m head (1 Working + 1 Stand-by) (for
Garden Hydrant)1 Set
36 Providing and fixing of package type skid mounted hydropneumatic system
comprising of:
(a) Horizontal / Vertical inline single/multistage centrifugal pumping set with
stainless steel SS stage casing and SS impellers with stainless steel shaft,
cast iron suction & discharge casing, connected to suitable capacity TEFC
ventilated induction motor of 2 pole, 2900rpm, suitable for 415±10% Volts,
3 phase, 50 Hz A.C. supply.
Page 13 of 119
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.No DescriptionTotal
Qty.Unit Rate Rate In Words MR-Amount
(b) Pressure vessel of non corrosive FRP composite construction lined with
NSF and/or FDA listed material, like high density polyethylene with fully
replaceable polyurethane. Air cell burst pressure of minimum of 5 times the
vessel operating pressure and cycle tested for 2,50,000 cycles.
No. and capacity of Pressure Vessel - 01 Nos. x 100 Ltrs.
(c) Electrical Control Panel including provision for cyclic operation of pumps -
Pump working sequence should change after every operation. Control
panel with programmable logic controller (PLC) with inbuilt PID controller ,
digital display with fluorescent screen, one no. 3 ph, 415±10%V, AC
variable speed drive of suitable capacity rating with inbuilt EN55011 class A
RFI filters, having standard function of BI loop, energy saving catching a
spinning load with speed search, auto hunting jog preset speeds, controlled
stop on loss of supply power loss side through, DDC injection breaking fast
stop. Drive should have selectable rated input frequency 50/60 Hz and
output frequency range of 0.5-32 Hz, contactors, overload relays and MCBs
should conform to IEC 898-1995 standards Ammeter, voltmeter. All trip
indications should blink in case of trip and panels should only be
accessible through an access code.
(d) Electronic Pressure switches having maximum pressure and differential
scale should confirming BS-6134 standards and IP55 protection class.
(e) Complete set system to be mounted on a common MS base frame and
shall follow following duty.
(f) The cost will include making necessary flanged suction and delivery
headers in GI (C class)
Page 14 of 119
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.No DescriptionTotal
Qty.Unit Rate Rate In Words MR-Amount
(g) Motor to be of the same make as the pump
(Vendor to submit performance curves and technical catalogue of the
proposed model for review & information)
The pump shall be selected for performance at best efficiency point.
However, the pump selection shall be suitable for performance with set point
@ + 20% of the rated head.
36.1 Domestic Capacity : 150 LPM each Pump (2 Working + 1 Standby) @ 75 M
head.1 Set
36.2 Flushing Capacity : 125 LPM each Pump (2 Working + 1 Standby) @ 75 M
head.1 Set
36.3 Hot Water Supply Capacity : 100 LPM each Pump (1 Working + 1 Standby)
@ 75 M head.1 Set
37 MULTIGRADE SAND FILTER (for Domestic )
Supply, installation, testing & commissioning of vertical self supporting Dual
Media Filter (DMF) fabricated from M.S as per IS : 2825, ASMI code,
complete with pressure gauges at inlet & outlet, sample cock, PVC face
piping with ABS multiport valves and all accessories, with initial charge of
filter media for Dual media filter with multi grade quartz sand & anthracite,
lining inside with PP and FRP wounded outside, testing and commissioning
complete.a) Capacity : 8000 LPH
b) Filtration rate : 18-20 M³/M²/hr
c) Max. operating pressure : 3.5 Kg/Sq.cm
d) Test pressure : 5.5 Kg/Sq.cm
e) Suggested Diameter :750mm 1 Set
Page 15 of 119
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.No DescriptionTotal
Qty.Unit Rate Rate In Words MR-Amount
38 WATER SOFTENER (for Domestic use)
Supply, installation, testing & commissioning of vertical self supporting
Softener fabricated from FRP as per IS : 2825, ASMI code, complete with
pressure gauges at inlet & outlet, sample cock, PVC face piping with ABS
multiport valves and all accessories, with initial charge of filter media for
softener with cation exchange resin, brine tank, lining inside with PP and
FRP wounded outside, testing and commissioning complete.
a) Hardness
i) Inlet : Upto 600 PPM
ii) Outlet : Domestic Zero (60-70 ppm)
b) Capacity : 135 Lpm
c) Regeneration Period : 4.5 hrs.
d) OBR (Out put between regeneration) : 36.5 M³
e) Operating pressure : 3.5 kg/Sq.cm
f) Test pressure : 5.5 Kg/Sq.cm 1 Set
39 Supplying, installing, testing and commissioning of Sodium Hypochloride
dosing system consisting of one HDPE tank of 300 litres capacity with a
positive displacement diaphragm dosing pump having variable flow rate of
0-6LPH. The motor shall be suitable for operation at 240 V / single phase
/50 Hz. Supply. The pump shall be supplied complete with necessary
polypropylene piping, valves, strainers, low level switch and injection
fittings. The pump shall be speed & stroke control Asia LMI / equivalent
make.
1 Set
GI (B class) : All piping after filter feed GI (B class) : All piping after filter feed
Page 16 of 119
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.No DescriptionTotal
Qty.Unit Rate Rate In Words MR-Amount
40 Supply, assembly, erection, testing and commissioning of SS submersible
non-clog pumps, suitable to handle basement drainage having the following
capacities with vortex impeller / grinder type, complete with 3 phase squirrel
cage submersible motor of required HP for 415 ± 10% volts, 3 phase, 50
Hz. A.C. supply cooled by surrounding liquid, submersible cable upto main
panel within the plant room, dry running preventor, G.I. guide pulling chain,
all the necessary piping and accessories, valves, delivery header etc. as
required complete in all respects. The rate will include electrical panel with
cyclic operation as supplied by the manufacturers)
The above installation shall be complete with sump pump lifting assembly,
ready made electro – galvanized MS lifting chain, GI pipe header complete
with discharge manifold, flanges, tee, elbow etc. complete including GI pipe
upto the top of sump and including GI union. Header shall be sized for both
pump working under delivery velocity of 1.5 m/sec.
40.1 Capacity of 250 lpm against a total head of 14 m (solid handling 10-12 mm)
(Pump room Drainage) (1 Working + 1 Stand by) (SS Body and SS Impeller
and shaft)
2 Set
41 Supplying, assembly, erection, testing and commissioning of magnetic level
sensors and controllers, CPVC probe tube, PP actuating float and all other
equipment required for the performance of the system to the satisfaction of
the engineer in charge complete including providing and fixing wiring from
control junction box near the UG tank to probes of required length,
interconnection wiring between level controller and the concerned contactor
in the starter panel as required. The level controller will perform the following
functions.
a) To switch on the pumps (including raw water pumps (Domestic Water
Treatment etc.) when the level of water in the supply water tank is low and
to cut off the pump when the level in the receiving water tank is high and
switch off the pumps when the level of water in the supply water tank is low.
b) To indicate 5 levels of water in all tanks through a control panel with LEDs
c) To start the pumps in a cyclic order.
The system shall be complete to ensure automatic quotation of pump in
accordance to water level in respective tanks.
The Contractor will include all the under ground and over head tanks and all
the pumps as required for level control in this item2 Set
Page 17 of 119
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.No DescriptionTotal
Qty.Unit Rate Rate In Words MR-Amount
42 Providing, fixing, jointing and testing in position the following heavy class
G.I. pipes conforming to IS:1239 cut to required lengths including all
necessary fittings (conforming to IS:1879) and specials such as bends, tees,
unions, reducers, flanges & plugs etc. fixing at wall/ceiling level supported
by clamps, hangers etc, (to be galvanized after fabrication) cutting hole in
wall/floor/slab and making good the same good with cement concrete 1:2:4 /
fire sealant complete as required.
42.1 32 mm dia 30 RM
42.2 40 mm dia 45 RM
42.3 50 mm dia 50 RM
42.4 65 mm dia 20 RM
42.5 80 mm dia 50 RM
42.6 100 mm dia 20 RM
42.7 150 mm dia 20 RM
Page 18 of 119
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.No DescriptionTotal
Qty.Unit Rate Rate In Words MR-Amount
43 Providing two coats of Synthetic enamel paint of approved shade on pipes
and supports as per pipe colour code over a coat of primer. Including
painting of legends with direction arrow as per the approval of the
Consultants / Project Manager.
43.1 65 mm dia 20 RM
43.2 80 mm dia 50 RM
43.3 100 mm dia 20 RM
43.4 150 mm dia 20 RM
44 Supply, installation, testing and commissioning of tanker inlet connection
complete with 80 mm dia GI inlet piping, hose inlet connection, MS cabinet
enclosure (epoxy painted after fabrication), pad locking arrangement, inlet
flexible hose complete with all necessary arrangement.
1 No.
45 Providing and fixing Butter fly valve Rated for PN16 pressure rating
including rubber gasket, flanges, nuts, bolts, washers & painting complete
as required.
45.1 50 mm dia 10 Nos.
45.2 65 mm dia 2 Nos.
45.3 80 mm dia 4 Nos.
45.4 100 mm dia 4 Nos.
45.5 150 mm dia 1 Nos.
Page 19 of 119
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.No DescriptionTotal
Qty.Unit Rate Rate In Words MR-Amount
46 Providing & fixing C.I. dual plate type check valve tested to a pressure of
15Kg/sqcm. Including rubber gasket, flanges, union, nuts, bolts, washers &
painting complete as required.
46.1 50 mm dia 2 Nos.
46.2 65 mm dia 2 Nos.
46.3 80 mm dia 4 Nos.
46.4 100 mm dia 4 Nos.
47 Providing & fixing C.I. 'Y' Strainer (screwed / flanged) with stainless steel
fine wire mesh perforated sheet basket with necessary flanges / union nuts,
bolts & washers complete as required (on pump suction).
47.1 50 mm dia 2 Nos.
47.2 65 mm dia 2 Nos.
47.3 80 mm dia 4 Nos.
47.4 100 mm dia 4 Nos.
48 Providing & fixing in position Vane Type mechanical water flow meter for
following pipe size
48.1 50 mm dia 1 No.
Page 20 of 119
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.No DescriptionTotal
Qty.Unit Rate Rate In Words MR-Amount
49 Supplying, assembling, erection, testing and commissioning of RO Water
treatment system and all its components of required size as per water test
analysis to make the water suitable for drinking, complete including the
following as mentioned below. The cost will include testing of permeate
water sample from a CPCB approved test laboratory, generating and
providing membrane analysis data form the licensed manufacturer's
software etc. Permeate water quantity = 600 lit/hr.
Minimum Recovery = 70%
Raw Water Characteristics - As per Water Test Analysis Report of Test
Laboratory to be got done by the supplier
Treated Water Quality
Turbidity : <1NTU
pH : 6.5-7.0
Total Hardness : < 10 ppm
Chlorides : < 10 ppm
Sulphates : < 5 ppm
TDS : < 50 ppm
SS Vertical centrifugal Raw Water Pump (1 Working + 1 Stand-by)
FRP Dual Media Filter
Antiscalant Dosing System including pump chemical dosing pump, tanks
etc.
Polypropylene Micron/cartridge Filter and SS housing
Stainless steel vertical multistage inline high pressure pump (1 Working)
including dry running protection
Spirally wounded RO Membranes
Composite FRP RO pressure tube/vessel
Automatic RO Module Cleaning System including chemical pump, cartridge
filter, tanks etc.
pH correction system incl. chemical dosing pump, tanks etc.
Instrumentation including flow meters, digital TDS meter, digital pH meter,
pressure gauges, low pressure switch, high pressure switch etc. complete.
uPVC (8 kg/cm2) piping and ABS valves for low pressure and SS-316,
schedule 10 piping and SS-316 valves for high pressure piping in the plant.
Electrical panel including all starters, overload relays, single phase
preventers, voltmeters, ammeters, MCB's, indicating lights, push buttons,
rocker switches, incomers, auto-manual switches etc. complete.
1 Set
Page 21 of 119
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.No DescriptionTotal
Qty.Unit Rate Rate In Words MR-Amount
F. SUBHEAD - VI - ELECTRICAL
50 Supply, assembly, erection, testing & commissioning of Plumbing panel
vermin proof free wall/floor mounting factory built sheet steel enclosed
nondrawout moduler type distribution board, fabricated out of 2.0mm thick
PCRC sheet, hinged doors of 1.6mm thick PCRC sheet, duly painted
complete with earth bar and aluminium bus bar & necessay indications,
mounted with the followings complete etc. as required
Incoming :
a) 100A, TPN MCCB - 1 No.
b) Phase indication lamp - 1 Set
c) (0-100A) Digital Ammeter with selector switch CT's and Control MCB - 1 Set
d) (0-500V) voltmeter with selector switch - 1 No.
e) 160A TPN 415V 50 Hz Aluminium Bus Bar.
Outgoing:
a) 20 A 4P MCB '10KA' - = 2 Nos.
b) 40 A 4P MCB '10KA' - 2 Nos.
c) DOL Starter suitable for 1 H.P motor complete with SPPR, Ammeter
contactor, relay, indication, Push Buttons complete as required. - 2 Sets
d) DOL Starter suitable for 7.5 H.P motor complete with SPPR, Ammeter
contactor, relay, indication, Push Buttons complete as required. - 2 Sets
Plumbing Panel as described above 1 Set
51 Supplying and making end termination with brass compression glands of
following sizes of 1.1 kV grade multicore aluminium conductor PVC
insulated and PVC sheathed cable etc. as required.
51.1 3 Core 4 Sqmm. (Aluminium) 4 Nos.
51.2 3 Core 6 Sqmm. (Aluminium) 4 Nos.
Page 22 of 119
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.No DescriptionTotal
Qty.Unit Rate Rate In Words MR-Amount
SUBHEAD-VII-SOLAR HOT WATER SYSTEM
52 Providing and fixing Solar Hot Water indirect Heating System with capacity-
1000 LPD using approved type of heating liquid medium comprising of flat
plate solar panels, including all interconnecting insulated G.I. piping,
sacrificial magnesium anode with steel core including valves on inlet, outlet,
Y stainer and a water meter on the inlet, air release valve all mounted on
galvanized MS sections complete with connection with the existing piping.
Flat plate solar collector panels of 2 x 1 m size approx. (10 nos.) the panels
enclosed in insulated collector boxes with single piece toughned glass 4 mm
thick and fixed with heat resistant gasket.
1.0 Set
PLUMBING TOTAL
Page 23 of 119
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.No DescriptionTotal
Qty.Unit Rate Rate In Words MR-Amount
SUB HEAD - I - Point Wiring
1 Supplying and fixing modular type Information Outlet RJ -45, CAT 6 Data ,
front plate and suitable size metal box on surface or in recess including
connections etc.complete as required.
86 Each
SUB HEAD - II -Distribution Board
2 Supplying and fixing following rating, four pole, 415 volts, isolator in the
existing MCB DB complete with connections, testing and commissioning etc.
as required.
2.1 32 amps 12 Each
SUB HEAD - III - Installation of Light Fitting
3 Supplying, Installation, connecting, testing and commissioning of the
following light fixtures complete with housing, reflectors, all accessories i.e.
copper wound Electronic ballast, HPF condensers, starters, holders,
hanging/fixing arrangements etc. complete as required
3.1 1x28 W T5 surface mounted Light fixture (TMS122 M 1xTL5-28W EBT)351 Nos.
3.2 2x18 W CFL Mounted (FBS095 2xPLC18W HFL) 98 Nos.
3.3 1x18 W CFL (FBS075 1xPLC/2P18W) 119 Nos.
3.4 1x9 W Foot Light 85 Nos.
3.5 1x9 W Mirror Light 39 Nos.
3.6 1x9 W Bulk Head (FXC 101 1xpl - S.2P 9WAC GR) 60 Nos.
3.7 4X14 watt Clean recessed type (4XTL5 - 14W EBAL FOP GT) 224 Nos.
3.8 1 x15 W LED Downlighter (BBS170 - 1XDLED - 5000 PSU WH) 200 Nos.
3.9 3 X 14 watt recessed type (TBS 4XTL5 - 14W EBPOF - WH) 166 Nos.
ELECTRICAL INTERNAL
Page 24 of 119
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.No DescriptionTotal
Qty.Unit Rate Rate In Words MR-Amount
ALL LIGHT FIXTURES TO BE LED TYPE ALINES OR EQUIVALENT
SUB HEAD - IV - FIRE DETECTION WORK
4 Supply, Installation, Testing and Commissioning of Microprocessor based
10 loop, Networkable analogue addressable type fire alarm control panel
with 640 character LCD display, The panel should be equipped with
sufficient numbers of loop with 20% spare capacity with each loop shall
have a minimum capacity of 159 analog addressable devices in one loop.
Four access levels, capable of taking Flash Scan devices, flash EPROM
sufficient numbers of programmable relay controls for controlling AHUs,
pressurization fans, ventilation fans at fire pump room, monitoring of fire
sprinkler and fire hydrant pump, 240 volts AC power supply, automatic
battery charger, 24 volts sealed lead acid batteries sufficient for 24 hours
normal working and then be capable of operating the system for 2 hours
during an emergency conditions as required. The Panel shall have
BACKNET CARD for integration. (UL 9th Edition Approved and NFPA
compliant)
4.1 8 Loop Panel 1 Nos.
5 Supply, Installation, Testing and Commissioning of Networked Fire Fighters
17 inch Touch screen Graphical Display Mimimc Panel (Incident
Commander) at main entry to inform & guide Fire Fighters for carrying out
Fire fighting operations. (UL 9th Edition Approved and NFPA compliant)
a) The software shall display along with icons representing standard building
objects (stairs, elevators, etc) to be shown on the floor plan
b) The software shall allow icons that represent hazardous materials stored in
a facility. screen that displays preprogrammed building contact information,
building occupancy and other general building information, display all active
fire, supervisory, and security events within an event list. The screen shall
also provide the arial view of entire building via touch screen navigation.
c) The equipment shall allow the importation of externally developed floor
plans in Windows Metafile (WMF), JPEG (JPG), Graphics Interchange
Format (GIF) and Bitmap (BMP) format.
1 Nos.
Page 25 of 119
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.No DescriptionTotal
Qty.Unit Rate Rate In Words MR-Amount
3 Supply, Installation, Testing and Commissioning of Automatic Floating
Sensitivity type Analog addressable Photo thermal smoke detector with
mounting based LED, Address Switch to programme the detectors,
complete as required. (UL 9th Edition Approved and NFPA compliant)
502 Nos.
4 Supply, Installation, Testing and Commissioning of Heat Detector complete
as required. (UL 9th Edition Approved and NFPA compliant)268 Nos.
5 Supplying, assembling, erection, testing & commissioning of Response
Indicator which consists of steady glowing LED. This LED shall be mounted
within a M.S.box and connected in parallel to the built in indicator of the
detector as per specifications. The RI shall come "ON" as soon as the
detector activates complete in all respects as per specification.
33 Nos.
6 Supply, Installation, Testing and Commissioning of Addressable type
manual call (Glass Break) Station complete with all accessories as per
specifications. (UL 9th Edition Approved and NFPA compliant)
24 Nos.
7 Supply, Installation, Testing and Commissioning of Directional Sounders
with 20 hz to 20 khz operating frequecy with minimum 8 distinct sound
patterns to indicate corridors, Exit doors, Move upward, move down ward
etc. to direct Occupants for fast & safe Evacuation as specified in NFPA 72 -
2007 edition. (UL 9th Edition Approved and NFPA compliant)
24 Nos.
8 Supply, Installation, Testing and Commissioning of Strobe Lights with 110
cd. 21 Nos.
9 Supply, Installation, Testing and Commissioning of Integrated 8 channel
Digital Voice Evacuation and 2 way Communication Fire Fighters System
capable to supervision of all circuits, with required suitable amplifiers for
speakers and accessories required to complete the system. The equipment
shall be of same make as panel. (UL 9th Edition Approved and NFPA
compliant)
1 Nos.
10 Supply, Installation, Testing and Commissioning of Fire panel supervised
70db-84db Ceiling Mounted Speakers complete with ceiling arrangements
and all accessories etc. as per specification. (UL 9th Edition Approved and
NFPA compliant)
202 Nos.
11 Supply, Installation, Testing and Commissioning of Fire panel supervised
70db-84db Wall Mounted Speakers complete with wall mounting
arrangement and all accessories etc. as per specification. (UL 9th Edition
Approved and NFPA compliant)
23 Nos.
Page 26 of 119
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.No DescriptionTotal
Qty.Unit Rate Rate In Words MR-Amount
12 Supply, Installation, Testing and Commissioning of 2 way communication
Fire Fighter's Telephone Jack fitted on wall including the cast of breaking
and making good the wall wherever required, complete in all respects as per
specifications. (UL 9th Edition Approved and NFPA compliant)
1 Nos.
13 Supply, Installation, Testing and Commissioning of 2 way communication
Fire Fighter's Handset complete with all accessories as per specifications.
(UL 9th Edition Approved and NFPA compliant)
21 Nos.
14 Supply, Installation, Testing and Commissioning of fault for isolating
shorted, dewired and loose circuits between two successive fault isolators
with automatic resetting arrangement complete in all respects as per
specifications. (UL 9th Edition Approved and NFPA compliant)
33 Nos.
15 Supplying, Installing, Testing and Commissioning of addressable Control
Module for Directional Sounder and Strobe etc complete as required and as
per specifications. (UL 9th Edition Approved and NFPA compliant)24 Nos.
16 Supplying, Installing, Testing and Commissioning of addressable Control
Module for Fire Fighters Telephone circuit with dual input complete as
required and as per specifications. (UL 9th Edition Approved and NFPA
compliant)
21 Nos.
17 Supply and installation of LPCB approved mineral insulated copper
conductor cables, construction as per BSEN 60702-1:2002 suitable for
withstanding 950 deg under fire conditions as per BS 6387 CWZ and 850
deg under fire conditions on one single sample as per BSEN 50200. Cable
should be manufactured with seamless copper tube and should be HFLS
sheathed.17.1 2 x 1.5 sqmm. 4200 Metre
18 Supplying, laying and fixing of following size of unarmoured, twisted copper
flexible FRLS cable in surface / recessed in suitable size of steel conduit
complete with all accessories as required.
18.1 2 C X 1.5 Sq mm 250 Metre
18.2 3 C X 2.5 Sq mm 250 Metre
19 Supplying and fixing of following sizes of GI flexible conduit along with
accessories etc. complete as required & approved by the Engineer In
charge.
20 mm 250 Metre
Page 27 of 119
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.No DescriptionTotal
Qty.Unit Rate Rate In Words MR-Amount
SUB HEAD - V - CABLE & CABLE TRAYS
SUPPLY AND LAYING OF CABLES / CABLE TRAYS / CABLE
TERMINATION
20 LT XLPE CABLES
Supply, laying, connecting, testing, commissioning of following sizes of PVC
sheathed LT XLPE aromoured, aluminium conductor cable 1.1KV grade, on
surface of wall or in existing trenches / hume pipe / cable trays including the
cost of digging and back filling the trenches, sand bricks / on existing cable
trays / walls including the cost of saddles, gutties, clamps etc. as required of
the following sizes.20.1 3.5c x 70 sq. mm cable 50 R.M.
20.2 3.5c x 50 sq. mm cable 90 R.M.
20.3 4c x 25 sq. mm cable 150 R.M.
20.4 4c x 16 sq. mm cable 130 R.M.
20.5 4c x 10 sq. mm cable 220 R.M.
20.6 4c x 6 sq. mm cable 300 R.M.
21 Supply and making end termination with brass compression glands for the
following PVC insulated XLPE / PVC sheathed 1.1KV grade cable including
cost of crimping lugs/ferrules, double compression glands, solder, cable
sockets, insulation tap etc complete as required.
21.1 4c x 6 sq. mm cable 24 Sets
Page 28 of 119
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.No DescriptionTotal
Qty.Unit Rate Rate In Words MR-Amount
SUB HEAD - VI - FLOOR PANELS
22 FLOOR PANEL ( GROUND FLOOR) (NORMAL SUPPLY)
Supplying, Installation, Testing and Commissioning of dust, damp and
vermin proof free floor standing / wall mounted factory built sheet steel
enclosed modular construction extendable panel, suitable for operatrion on
415 + 10% volts, 50 Hz AC 3 phase 4 wire system fabricated out of suitable
sized square tubular section and covered with 2.0mm thick CRCA sheet,
hinged doors of 1.6mm thick CRCA sheet, duly painted complete with
aluminium bus bars, interconnection with solid copper conductor wires /
aluminium strips, neutral links, earth bus etc. necessary metering
protections & indications and mounted with the following as per drawing and
technical specifications attached etc. complete as required.
Incoming:
1 No. of 100 Amp 4P MCCB of 25 kA Breaking capacity with On Indicating
Lamp with 2A SP MCB back-up.
Metering incoming:
1 No. Intelligent multifunction digital panel meters of class 1.0 accuracy with
communication interface port RS 485 for recording V , A , KWHr with
suitable rating CTs, CT shorting links & Control MCB's etc. as required.
R,Y,B & ON/OFF indicating lamp with control MCB's.
Bus Bars:
Electrolytic high conductivity aluminium three phase and neutral busbars
rated at 433V,50 Hz., 160 amps, 25kA, insulated with heat shrinkable
coloured PVC sleeves & clip on shrouds for joints as required.
Outgoing:-
All outgoing feeders shall be provided with On indicating lamp with MCB
protection.
a) 63A 4P MCB with 10kA Breaking Capacity - 2 Nos.
b) 40A 4P MCB with 10kA Breaking Capacity -3 Nos.
c) 32A 4P MCB with 10kA Breaking Capacity - 2 No.
Panel Described as above.& as per SLD 1 Set
Page 29 of 119
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.No DescriptionTotal
Qty.Unit Rate Rate In Words MR-Amount
23 FLOOR PANEL ( FIRST AND SECOND FLOOR) (NORMAL SUPPLY)
Supplying, Installation, Testing and Commissioning of dust, damp and
vermin proof free floor standing / wall mounted factory built sheet steel
enclosed modular construction extendable panel, suitable for operatrion on
415 + 10% volts, 50 Hz AC 3 phase 4 wire system fabricated out of suitable
sized square tubular section and covered with 2.0mm thick CRCA sheet,
hinged doors of 1.6mm thick CRCA sheet, duly painted complete with
aluminium bus bars, interconnection with solid copper conductor wires /
aluminium strips, neutral links, earth bus etc. necessary metering
protections & indications and mounted with the following as per drawing and
technical specifications attached etc. complete as required.
Incoming:
1 No. of 63 Amp 4P MCCB of 25 kA Breaking capacity with On Indicating
Lamp with 2A SP MCB back-up.
Metering incoming:
1 No. Intelligent multifunction digital panel meters of class 1.0 accuracy with
communication interface port RS 485 for recording V , A , KWHr with
suitable rating CTs, CT shorting links & Control MCB's etc. as required.
R,Y,B & ON/OFF indicating lamp with control MCB's.
Page 30 of 119
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.No DescriptionTotal
Qty.Unit Rate Rate In Words MR-Amount
Bus Bars:
Electrolytic high conductivity aluminium three phase and neutral busbars
rated at 433V,50 Hz., 100 amps, 25kA, insulated with heat shrinkable
coloured PVC sleeves & clip on shrouds for joints as required.
Outgoing:-
All outgoing feeders shall be provided with On indicating lamp with MCB
protection.
a) 63A 4P MCB with 10kA Breaking Capacity - 1 Nos.
b) 40A 4P MCB with 10kA Breaking Capacity -2Nos.
c) 32A 4P MCB with 10kA Breaking Capacity - 1 No.
Panel Described as above.& as per SLD 2 Set
24 FLOOR PANEL ( THIRD FLOOR) (NORMAL SUPPLY)
Supplying, Installation, Testing and Commissioning of dust, damp and
vermin proof free floor standing / wall mounted factory built sheet steel
enclosed modular construction extendable panel, suitable for operatrion on
415 + 10% volts, 50 Hz AC 3 phase 4 wire system fabricated out of suitable
sized square tubular section and covered with 2.0mm thick CRCA sheet,
hinged doors of 1.6mm thick CRCA sheet, duly painted complete with
aluminium bus bars, interconnection with solid copper conductor wires /
aluminium strips, neutral links, earth bus etc. necessary metering
protections & indications and mounted with the following as per drawing and
technical specifications attached etc. complete as required.
Incoming:
1 No. of 100 Amp 4P MCCB of 25 kA Breaking capacity with On Indicating
Lamp with 2A SP MCB back-up.
Metering incoming:
1 No. Intelligent multifunction digital panel meters of class 1.0 accuracy with
communication interface port RS 485 for recording V , A , KWHr with
suitable rating CTs, CT shorting links & Control MCB's etc. as required.
R,Y,B & ON/OFF indicating lamp with control MCB's.
Bus Bars:
Electrolytic high conductivity aluminium three phase and neutral busbars
rated at 433V,50 Hz., 100 amps, 25kA, insulated with heat shrinkable
coloured PVC sleeves & clip on shrouds for joints as required.
Page 31 of 119
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.No DescriptionTotal
Qty.Unit Rate Rate In Words MR-Amount
Outgoing:-
All outgoing feeders shall be provided with On indicating lamp with MCB
protection.
a) 63A 4P MCB with 10kA Breaking Capacity - 1 No.
b) 40A 4P MCB with 10kA Breaking Capacity -2Nos.
c) 32A 4P MCB with 10kA Breaking Capacity - 2 Nos..
Panel Described as above.& as per SLD 1 Set
25 FLOOR PANEL (FOURTH, FIFTH,SEVENTH AND EIGHTH FLOOR)
(NORMAL SUPPLY)
Supplying, Installation, Testing and Commissioning of dust, damp and
vermin proof free floor standing / wall mounted factory built sheet steel
enclosed modular construction extendable panel, suitable for operatrion on
415 + 10% volts, 50 Hz AC 3 phase 4 wire system fabricated out of suitable
sized square tubular section and covered with 2.0mm thick CRCA sheet,
hinged doors of 1.6mm thick CRCA sheet, duly painted complete with
aluminium bus bars, interconnection with solid copper conductor wires /
aluminium strips, neutral links, earth bus etc. necessary metering
protections & indications and mounted with the following as per drawing and
technical specifications attached etc. complete as required.
Incoming:
1 No. of 160 Amp 4P MCCB of 25 kA Breaking capacity with On Indicating
Lamp with 2A SP MCB back-up.
Metering incoming:
1 No. Intelligent multifunction digital panel meters of class 1.0 accuracy with
communication interface port RS 485 for recording V , A , KWHr with
suitable rating CTs, CT shorting links & Control MCB's etc. as required.
R,Y,B & ON/OFF indicating lamp with control MCB's.
Bus Bars:
Electrolytic high conductivity aluminium three phase and neutral busbars
rated at 433V,50 Hz., 250 amps, 25kA, insulated with heat shrinkable
coloured PVC sleeves & clip on shrouds for joints as required.
Page 32 of 119
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.No DescriptionTotal
Qty.Unit Rate Rate In Words MR-Amount
Outgoing:-
All outgoing feeders shall be provided with On indicating lamp with MCB
protection.
a) 63A 4P MCB with 10kA Breaking Capacity - 1 Nos.
b) 40A 4P MCB with 10kA Breaking Capacity -4 Nos.
c) 32A 4P MCB with 10kA Breaking Capacity - 2 No.
Panel Described as above.& as per SLD 4 Set
Page 33 of 119
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.No DescriptionTotal
Qty.Unit Rate Rate In Words MR-Amount
26 FLOOR PANEL ( SERVICE FLOOR) (NORMAL SUPPLY)
Supplying, Installation, Testing and Commissioning of dust, damp and
vermin proof free floor standing / wall mounted factory built sheet steel
enclosed modular construction extendable panel, suitable for operatrion on
415 + 10% volts, 50 Hz AC 3 phase 4 wire system fabricated out of suitable
sized square tubular section and covered with 2.0mm thick CRCA sheet,
hinged doors of 1.6mm thick CRCA sheet, duly painted complete with
aluminium bus bars, interconnection with solid copper conductor wires /
aluminium strips, neutral links, earth bus etc. necessary metering
protections & indications and mounted with the following as per drawing and
technical specifications attached etc. complete as required.
Incoming:
1 No. of 63 Amp 4P MCCB of 25 kA Breaking capacity with On Indicating
Lamp with 2A SP MCB back-up.
Metering incoming:
1 No. Intelligent multifunction digital panel meters of class 1.0 accuracy with
communication interface port RS 485 for recording V , A , KWHr with
suitable rating CTs, CT shorting links & Control MCB's etc. as required.
R,Y,B & ON/OFF indicating lamp with control MCB's.
Bus Bars:
Electrolytic high conductivity aluminium three phase and neutral busbars
rated at 433V,50 Hz., 100 amps, 25kA, insulated with heat shrinkable
coloured PVC sleeves & clip on shrouds for joints as required.
Outgoing:-
All outgoing feeders shall be provided with On indicating lamp with MCB
protection.
a) 63A 4P MCB with 10kA Breaking Capacity - 1 Nos.
b) 40A 4P MCB with 10kA Breaking Capacity - 2 Nos.
c) 32A 4P MCB with 10kA Breaking Capacity - 1 No.
Panel Described as above.& as per SLD 1 Set
Page 34 of 119
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.No DescriptionTotal
Qty.Unit Rate Rate In Words MR-Amount
27 FLOOR PANEL ( NINTH FLOOR) (NORMAL SUPPLY)
Supplying, Installation, Testing and Commissioning of dust, damp and
vermin proof free floor standing / wall mounted factory built sheet steel
enclosed modular construction extendable panel, suitable for operatrion on
415 + 10% volts, 50 Hz AC 3 phase 4 wire system fabricated out of suitable
sized square tubular section and covered with 2.0mm thick CRCA sheet,
hinged doors of 1.6mm thick CRCA sheet, duly painted complete with
aluminium bus bars, interconnection with solid copper conductor wires /
aluminium strips, neutral links, earth bus etc. necessary metering
protections & indications and mounted with the following as per drawing and
technical specifications attached etc. complete as required.
Incoming:
1 No. of 63 Amp 4P MCCB of 25 kA Breaking capacity with On Indicating
Lamp with 2A SP MCB back-up.
Metering incoming:
1 No. Intelligent multifunction digital panel meters of class 1.0 accuracy with
communication interface port RS 485 for recording V , A , KWHr with
suitable rating CTs, CT shorting links & Control MCB's etc. as required.
R,Y,B & ON/OFF indicating lamp with control MCB's.
Bus Bars:
Electrolytic high conductivity aluminium three phase and neutral busbars
rated at 433V,50 Hz., 100 amps, 25kA, insulated with heat shrinkable
coloured PVC sleeves & clip on shrouds for joints as required.
Outgoing:-
All outgoing feeders shall be provided with On indicating lamp with MCB
protection.
a) 63A 4P MCB with 10kA Breaking Capacity - 1 Nos.
b) 40A 4P MCB with 10kA Breaking Capacity - 2 Nos.
c) 32A 4P MCB with 10kA Breaking Capacity - 1 No.
Panel Described as above.& as per SLD 1 Set
Page 35 of 119
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.No DescriptionTotal
Qty.Unit Rate Rate In Words MR-Amount
28 FLOOR PANEL ( GROUND FLOOR) ( UPS SUPPLY)
Supplying, Installation, Testing and Commissioning of dust, damp and
vermin proof free floor standing / wall mounted factory built sheet steel
enclosed modular construction extendable panel, suitable for operatrion on
415 + 10% volts, 50 Hz AC 3 phase 4 wire system fabricated out of suitable
sized square tubular section and covered with 2.0mm thick CRCA sheet,
hinged doors of 1.6mm thick CRCA sheet, duly painted complete with
aluminium bus bars, interconnection with solid copper conductor wires /
aluminium strips, neutral links, earth bus etc. necessary metering
protections & indications and mounted with the following as per drawing and
technical specifications attached etc. complete as required.
Incoming:
1 No. of 100 Amp 4P MCCB of 25 kA Breaking capacity with On Indicating
Lamp with 2A SP MCB back-up.
Metering incoming:
1 No. Intelligent multifunction digital panel meters of class 1.0 accuracy with
communication interface port RS 485 for recording V , A , KWHr with
suitable rating CTs, CT shorting links & Control MCB's etc. as required.
R,Y,B & ON/OFF indicating lamp with control MCB's.
Bus Bars:
Electrolytic high conductivity aluminium three phase and neutral busbars
rated at 433V,50 Hz., 160 amps, 25kA, insulated with heat shrinkable
coloured PVC sleeves & clip on shrouds for joints as required.
Outgoing:-
All outgoing feeders shall be provided with On indicating lamp with MCB
protection.
a) 63A 4P MCB with 10kA Breaking Capacity - 3 Nos.
b) 40A 4P MCB with 10kA Breaking Capacity - 2 Nos.
c) 32A 4P MCB with 10kA Breaking Capacity - 1 No.
Panel Described as above.& as per SLD 1 Set
Page 36 of 119
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.No DescriptionTotal
Qty.Unit Rate Rate In Words MR-Amount
29 FLOOR PANEL ( THIRD FLOOR) ( UPS SUPPLY)
Supplying, Installation, Testing and Commissioning of dust, damp and
vermin proof free floor standing / wall mounted factory built sheet steel
enclosed modular construction extendable panel, suitable for operatrion on
415 + 10% volts, 50 Hz AC 3 phase 4 wire system fabricated out of suitable
sized square tubular section and covered with 2.0mm thick CRCA sheet,
hinged doors of 1.6mm thick CRCA sheet, duly painted complete with
aluminium bus bars, interconnection with solid copper conductor wires /
aluminium strips, neutral links, earth bus etc. necessary metering
protections & indications and mounted with the following as per drawing and
technical specifications attached etc. complete as required.
Incoming:
1 No. of 63 Amp 4P MCCB of 25 kA Breaking capacity with On Indicating
Lamp with 2A SP MCB back-up.
Metering incoming:
1 No. Intelligent multifunction digital panel meters of class 1.0 accuracy with
communication interface port RS 485 for recording V , A , KWHr with
suitable rating CTs, CT shorting links & Control MCB's etc. as required.
R,Y,B & ON/OFF indicating lamp with control MCB's.
Bus Bars:
Electrolytic high conductivity aluminium three phase and neutral busbars
rated at 433V,50 Hz., 100 amps, 25kA, insulated with heat shrinkable
coloured PVC sleeves & clip on shrouds for joints as required.
Page 37 of 119
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.No DescriptionTotal
Qty.Unit Rate Rate In Words MR-Amount
Outgoing:-
All outgoing feeders shall be provided with On indicating lamp with MCB
protection.
a) 63A 4P MCB with 10kA Breaking Capacity - 1 Nos.
b) 40A 4P MCB with 10kA Breaking Capacity - 2 Nos.
c) 32A 4P MCB with 10kA Breaking Capacity - 1 No.
Panel Described as above.& as per SLD 1 Set
30 FLOOR PANEL ( FOURTH , FIFTH , SEVENTH AND EIGHTH FLOOR) (
UPS SUPPLY)
Supplying, Installation, Testing and Commissioning of dust, damp and
vermin proof free floor standing / wall mounted factory built sheet steel
enclosed modular construction extendable panel, suitable for operatrion on
415 + 10% volts, 50 Hz AC 3 phase 4 wire system fabricated out of suitable
sized square tubular section and covered with 2.0mm thick CRCA sheet,
hinged doors of 1.6mm thick CRCA sheet, duly painted complete with
aluminium bus bars, interconnection with solid copper conductor wires /
aluminium strips, neutral links, earth bus etc. necessary metering
protections & indications and mounted with the following as per drawing and
technical specifications attached etc. complete as required.
Incoming:
1 No. of 100 Amp 4P MCCB of 25 kA Breaking capacity with On Indicating
Lamp with 2A SP MCB back-up.
Metering incoming:
1 No. Intelligent multifunction digital panel meters of class 1.0 accuracy with
communication interface port RS 485 for recording V , A , KWHr with
suitable rating CTs, CT shorting links & Control MCB's etc. as required.
R,Y,B & ON/OFF indicating lamp with control MCB's.
Bus Bars:
Electrolytic high conductivity aluminium three phase and neutral busbars
rated at 433V,50 Hz., 100 amps, 25kA, insulated with heat shrinkable
coloured PVC sleeves & clip on shrouds for joints as required.
Page 38 of 119
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.No DescriptionTotal
Qty.Unit Rate Rate In Words MR-Amount
Outgoing:-
All outgoing feeders shall be provided with On indicating lamp with MCB
protection.
a) 63A 4P MCB with 10kA Breaking Capacity - 1 Nos.
b) 40A 4P MCB with 10kA Breaking Capacity - 3 Nos.
c) 32A 4P MCB with 10kA Breaking Capacity - 1 No.
Panel Described as above.& as per SLD 4 Set
31 FLOOR PANEL ( SIXTH FLOOR) ( UPS SUPPLY)
Supplying, Installation, Testing and Commissioning of dust, damp and
vermin proof free floor standing / wall mounted factory built sheet steel
enclosed modular construction extendable panel, suitable for operatrion on
415 + 10% volts, 50 Hz AC 3 phase 4 wire system fabricated out of suitable
sized square tubular section and covered with 2.0mm thick CRCA sheet,
hinged doors of 1.6mm thick CRCA sheet, duly painted complete with
aluminium bus bars, interconnection with solid copper conductor wires /
aluminium strips, neutral links, earth bus etc. necessary metering
protections & indications and mounted with the following as per drawing and
technical specifications attached etc. complete as required.
Incoming:
1 No. of 63 Amp 4P MCCB of 25 kA Breaking capacity with On Indicating
Lamp with 2A SP MCB back-up.
Metering incoming:
1 No. Intelligent multifunction digital panel meters of class 1.0 accuracy with
communication interface port RS 485 for recording V , A , KWHr with
suitable rating CTs, CT shorting links & Control MCB's etc. as required.
R,Y,B & ON/OFF indicating lamp with control MCB's.
Page 39 of 119
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.No DescriptionTotal
Qty.Unit Rate Rate In Words MR-Amount
Bus Bars:
Electrolytic high conductivity aluminium three phase and neutral busbars
rated at 433V,50 Hz., 100 amps, 25kA, insulated with heat shrinkable
coloured PVC sleeves & clip on shrouds for joints as required.
Outgoing:-
All outgoing feeders shall be provided with On indicating lamp with MCB
protection.
a) 63A 4P MCB with 10kA Breaking Capacity - 1 Nos.
b) 40A 4P MCB with 10kA Breaking Capacity - 3 Nos.
Panel Described as above.& as per SLD 1 Set
32 FLOOR PANEL ( NINTH FLOOR) ( UPS SUPPLY)
Supplying, Installation, Testing and Commissioning of dust, damp and
vermin proof free floor standing / wall mounted factory built sheet steel
enclosed modular construction extendable panel, suitable for operatrion on
415 + 10% volts, 50 Hz AC 3 phase 4 wire system fabricated out of suitable
sized square tubular section and covered with 2.0mm thick CRCA sheet,
hinged doors of 1.6mm thick CRCA sheet, duly painted complete with
aluminium bus bars, interconnection with solid copper conductor wires /
aluminium strips, neutral links, earth bus etc. necessary metering
protections & indications and mounted with the following as per drawing and
technical specifications attached etc. complete as required.
Incoming:
1 No. of 63 Amp 4P MCCB of 25 kA Breaking capacity with On Indicating
Lamp with 2A SP MCB back-up.
Metering incoming:
1 No. Intelligent multifunction digital panel meters of class 1.0 accuracy with
communication interface port RS 485 for recording V , A , KWHr with
suitable rating CTs, CT shorting links & Control MCB's etc. as required.
Page 40 of 119
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.No DescriptionTotal
Qty.Unit Rate Rate In Words MR-Amount
R,Y,B & ON/OFF indicating lamp with control MCB's.
Bus Bars:
Electrolytic high conductivity aluminium three phase and neutral busbars
rated at 415V,50 Hz., 100 amps, 25kA, insulated with heat shrinkable
coloured PVC sleeves & clip on shrouds for joints etc. as required.
Outgoing:-
All outgoing feeders shall be provided with On indicating lamp with MCB
protection.
a) 63A 4P MCB with 10kA Breaking Capacity - 2 Nos.
b) 40A 4P MCB with 10kA Breaking Capacity - 3 Nos.
Panel Described as above.& as per SLD 1 Set
Page 41 of 119
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.No DescriptionTotal
Qty.Unit Rate Rate In Words MR-Amount
SUB HEAD - VII - CCTV SURVEILLANCE SYSTEM
33 Supply, installation, testing & commissioning of 1/3" CCD High Resolution
580 TVL, coloured fixed dome camera with 2.8-10mm varifocal LENS,
Minimum illumination 0.001 lx,24 V DC operation, having features like wide
dynamic range, True Day Night, Digital Noise Reduction, picture in picture,
Quad View, backlight compensation, line lock and phase adjustment, UL
listed etc. complete as required & approved by the Engineer In charge.
10 Each
34 Supply, installation, testing & commissioning of 1/4" CCD High Resolution
540 TVL, coloured 26x Optical Zoom, 12x Digital Zoom PTZ (360 degree)
camera with 3.5mm~91mm LENS, Weather-proof IP66 Housing, 24 V DC
operation, having features like backlight compensation, wide dynamic
range,128 preset positions,3 self-learning auto tracks UL listed etc.
complete as required & approved by the Engineer In charge.
2 Each
35 Supply, installation, testing & commissioning of 1/3" CCD High Resolution
580 TVL, coloured fixed BOX camera, Minimum illumination 0.001 lx, wide
dynamic range, CS mount 2.7 to 13mm LENS, Outdoor IP66 Weather-Proof
Housing, 24 V DC operation, UL listed etc. complete as required &
approved by the Engineer In charge.
2 Each
36 Supply, installation, testing & commissioning of 400/480fps D1 recording
rate for up to 16 channels, 8 SATA HDD capacity, up to 16TB storage,
Embedded LINUX, H.264 compression, Multi-screen Channel 1,4,9,16,
eSATA port.16 channels D1 resolution playback simultaneously (forward/
reverse, fast playback, slow playback, freeze). UL Listed etc. complete as
required.
1 Each
37 Supply, installation, testing & commissioning of 21" high resolution colour
monitor, UL listed etc. complete as required & approved by the Engineer In
charge.
1 Each
38 Supply, installation, testing & commissioning of 12 V DC power supply unit
etc. complete as required & approved by the Engineer In charge. 14 Each
39 Supplying, laying, terminating, connecting, testing & commissioning of 3
Core x 1.5 sqmm unarmoured copper cable with termination on both ends,
ferrule numbering, with complete accessories etc. complete as required &
approved by the Engineer In charge.
100 Metre
Page 42 of 119
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.No DescriptionTotal
Qty.Unit Rate Rate In Words MR-Amount
40 Supplying and fixing of following sizes of GI flexible conduit along with
accessories etc. complete as required & approved by the Engineer In
charge.
40.1 20 mm 50.00 Metre
40.2 25 mm 50.00 Metre
41 Supply, laying, testing and commissioning of the following co-axial PVC
insulated conductor cable in existing surface / recessed conduit etc. and
including making terminal joints, etc. complete as required & approved by
the Engineer In charge.
41.1 RG - 11 350.00 Metre
41.2 RG - 6 RO Metre
SUB HEAD - VIII - Lightning Protection
Supply & installation of Advance Lightning Protection System including all
necessary fixing accessories & effective connections complying the detailed
technical specifications given therein.
42 Supply, installation, testing & commissioning of ESE Stormaster type
Lightning Protection complete with the Lightning Air Terminal - Configured
as a Spheroid which is comprised of separate electrically isolated 4 panels
surrounding an Earthed Central Finial. The Insulation material used to
electrically isolate the panels shall be comprised of a base polymer which
provides high Ozone & UV resistance with a di-electric strength of 24-38
KV/mm tested as per NFC 17-102 & IEC 60-1:1989. The ESE terminal shall
be tested & certified by CPRI (Central Power Research Institute), Govt of
India for the Impulse current of 45 KA (8/20 micro sec) with 5 positive & 5
negative impulse. The ESE Stormaster terminal shall be approved from
DGMS (Director General of Mines Safety), Govt of India.
42.1 Stormaster 30 SS - 48 mtrs (Level 1 / High Protection) 1 Nos.
Page 43 of 119
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.No DescriptionTotal
Qty.Unit Rate Rate In Words MR-Amount
42.2 Supply & installation of Mast (G.I. pipe of 2 to 5 mtrs height) for mounting
the terminal & adaptor with the Stormaster ESE Air Terminal along with
supporting stray wires, etc.
1 Nos.
42.3 Supply & installation of advance maintenance free Chemical Gel Earthing of
Dual Pipe Technology (GI) of 3mtr long 80mm dia of outer shell (MS) with
the 50mm dia of inner shell (MS) with 80-100 microns galvanized JK
CHEMRODE filled with highly conducting metallic compounds with the
permanent sealings at both the ends with the lead terminal of 50x10mm size
at the top along with 50 Kgs of RESLOW (mixture of Sulphate, Silica,
Alumina, Iron Oxide, Titanium Oxide, Calcium Oxide, Potassium Oxide,
Chloride, Nickel Oxide, Magnesium Oxide, Sodium Oxide, Zinc Oxide, etc)
Resistance Lowering Grounding Minerals. The loss on ignition by mass of
the chemical compound RESLOW shall be less than 20%. The chemical
compound should be tested and certified by any International accredited
and BIS (Bureau of Indian Standards) accredited laboratory. The testing
laboratory should be ISO 9001 & ISO 14001 certified. The JK CHEMRODE
shall be duly tested & certified by CPRI (Central Power Research Institute),
Govt of India for a minimum short circuit current of 30 KA rms. The chemical
earth electrode manufacturer shall be an ISO 9001:2008 & ISO 14001:2004
certified organization.
1 Nos.
42.4 Supply & installation of Lightning Strike Recorder - 6 digits display to record
the lightning current in an IP 67 enclosure with the minimum sensitivity of
1500A & maximum capacity of 220 KA (8/20 micro second waveform)
1 Nos.
42.5 Supply & installation of down conductor of 70 sq.mm single core insulated
flexible copper cable with necessary accessories, etc.100 Mtr.
SUB HEAD -IX - EARTHING SYSTEM
43 Supply, installation and testing of advance maintenance free Chemical Gel
Earthing of Single Pipe Technology (Copper) of 3mtr long 63mm dia
CHEMRODE filled with highly conducting metallic compounds with the
permenant sealings at the both the ends with the lead terminal 32x10mm at
the top along with 50 Kgs of RESLOW (mixture of Sulphate, Silica, Alumina,
Iron Oxide, Titanium Oxide, Calcium Oxide, Potassium Oxide, Chloride,
Nickel Oxide, Magnesium Oxide, Sodium Oxide, Zinc Oxide, etc) Resistance
Lowering Grounding Minerals. The loss on ignition by mass of the chemical
compound RESLOW shall be less than 20%. The chemical compound
should be tested and certified by any International accredited and BIS
(Bureau of Indian Standards) accredited laboratory. The chemical earth
electrode manufacturer shall be an ISO 9001:2008 & ISO 14001:2004
certified organization.
Page 44 of 119
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.No DescriptionTotal
Qty.Unit Rate Rate In Words MR-Amount
The Earth pit should be covered with heavy duty polyplastic weather proof
chamber.10 Sets
Page 45 of 119
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.No DescriptionTotal
Qty.Unit Rate Rate In Words MR-Amount
44 Supply, installation and testing of advance maintenance free Chemical Gel
Earthing of Dual Pipe Technology (GI) of 3mtr long 80mm dia of outer shell
(MS) with the 50mm dia of inner shell (MS) of 80-100 microns galvanized
CHEMRODE filled with highly conducting metallic compounds with the
permenant sealings at both the ends with the lead terminal of 50x10mm size
at the top along with 50 Kgs of RESLOW (mixture of Sulphate, Silica,
Alumina, Iron Oxide, Titanium Oxide, Calcium Oxide, Potassium Oxide,
Chloride, Nickel Oxide, Magnesium Oxide, Sodium Oxide, Zinc Oxide, etc)
Resistance Lowering Grounding Minerals. The loss on ignition by mass of
the chemical compound RESLOW shall be less than 20%. The chemical
compound should be tested and certified by any International accredited
and BIS (Bureau of Indian Standards) accredited laboratory. The testing
laboratory should be ISO 9001 & ISO 14001 certified. The CHEMRODE
shall be be duly tested & certified by CPRI (Central Power Research
Institute), Govt of India for a minimum short circuit current of 30 KA rms.
The chemical earth electrode manufacturer shall be an ISO 9001:2008 &
ISO 14001:2004 certified organization.
The Earth pit should be covered with heavy duty polyplastic weather proof
chamber.4 Nos.
45 Providing and fixing 50 mm X 6 mm Copper strip on surface or in recess for
connections etc, as required100 Mtr.
46 Providing and fixing 50 mm X 6 mm size of copper strip with PVC insulated
sleeves in 80 mm dia 'B' class G.I. pipe from earth electrode as required 80 Mtr.
47 Providing and fixing 50 mm X 6 mm G.I. strip on surface or in recess for
connections etc, as required60 Mtr.
Page 46 of 119
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.No DescriptionTotal
Qty.Unit Rate Rate In Words MR-Amount
48 Providing and fixing 50 mm X 6 mm size of G.I. strip with PVC insulated
sleeves in 80 mm dia 'B' class G.I. pipe from earth electrode as required 30 Mtr.
49 Providing and fixing 40 mm X 6 mm copper strip with PVC insulated sleeves
on surface or in recess for connections etc, as required (For UPS) 180 Mtr.
50 Providing and fixing 25 mm X 6 mm size of copper strip with PVC insulated
sleeves in 40 mm dia 'B' class G.I. pipe from earth electrode as required (
Equipment)
80 Mtr.
51 Providing and fixing 25 mm X 6 mm copper strip with PVC insulated sleeves
on surface or in recess for connections etc, as required (Equipment). 120 Mtr.
52 Providing and fixing 20 mm X 3 mm size of copper strip with PVC insulated
sleeves in 40 mm dia 'B' class G.I. pipe from earth electrode as required (
EPABX, Server Room)
100 Mtr.
53 Providing and fixing 20 mm X 3 mm copper strip with PVC insulated sleeves
on surface or in recess for connections etc, as required. ( EPABX, Server
Room)
200 Mtr.
54 Providing and fixing 6 SWG dia GI wire on surface or in recess for loop
earthing along with the existing surface / recessed conduits / submain wiring
/ cable as required.
800 Mtr.
55 Providing and fixing 8 SWG dia GI wire on surface or in recess for loop
earthing along with the existing surface / recessed conduits / submain wiring
/ cable as required.
400 Mtr.
Page 47 of 119
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.No DescriptionTotal
Qty.Unit Rate Rate In Words MR-Amount
SUB HEAD - X : UPS
56 Supply of online load sharing of UPS system of following ratings with
computer communication possibilities consisting of standard software,
double conversion system suitable for providing power supply to
computers/servers sports lighting, corridor lighting delivery atleast 30
minutes backup, suitable for incoming 415 volts, 3phase +10% -15%, 50Hz
supply and three phase output voltage, including, rectifier/dual converter,
bypass switch, inverter, filter. Bypass & static transfer switch for automatic
switch over, providing static bypass module, high switching frequency
microprocessor based with built-in technical protections like short circuits,
over load, high / low voltage cut off protection of load from source inclusive
of bypass facility without giving any break of power,
1 Set
Microprocessor/ software controlled annunciation, protection (including
against input phase reversal), and menu run diagnostic module, associated
cabling, connections, termination, erection including associated foundation/
masonry or RCC work for mounting on base channels etc. complete as
required and as per specifications. 100 KVA x 3 Sets (Parallel Redundant)
57 Providing & Fixing of VRLA Battery Banks and BCB consisting of 2V, SMF
Type suitable for UPS System for 30 mins backup for individual UPS.1 Set
Page 48 of 119
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.No DescriptionTotal
Qty.Unit Rate Rate In Words MR-Amount
Sub Head -XI: Access Control System
A Supply, installation, testing and commissioning of access control system
complete with all accessories, components, Graphical integrated Access
control management Software along with time & attendance to manage
required number of doors. required to make the system full functional and
consisting of the following equipments all as specified.
58 Supplying, installation, testing and commissioning of Graphical integrated
Access control management as per specification along with 2 client
Licenses complete in all respects as per specifications.
1 Lot
59 Supplying, installation and commissioning of Intelligent 4 Door configuration
works Peer-to-peer direct communication via TCP-IP controller to support
Antipass back feature, Handling capacity of 10,000 (min) Cardholders, 16
(min) time zones, 64 (min) geographical zones and 120 (min) access levels.
2.500 (min) transactions (transits and events) stored on Flash EPROM
removable cartridge and have optional memory expansion for Up to 18000
transactions including power supply control unit with relevant control unit
complete in all respects as per specifications.
1 Set
60 Supply, installation, testing and commissioning of Smart card Readers (2”-
3") complete as per specification.10 Nos.
61 Supply, installation, testing and commissioning of Electromagnetic locks,
suitable for single leaf door with magnetic contacts as per specification. 10 Nos.
62 Supply, installation, testing and commissioning of exit push button, complete
in all respects.10 Nos.
63 Supply of Smart cards, conforming to ISO thickness all as specified. 50 Nos.
64 Thermal printing only of Smart cards (Variable colour data on front sides
and fixed colour data on rear.) layout and colours format approved by Client
complete as per specification.
50 Nos.
65 Supply, drawing, installation, testing and commissioning of PVC insulated
and PVC sheathed 8 core (4 pair) 0.6 sq.mm. twisted pair standard cable in
the existing surface / recessed PVC/steel conduit as required.
300 Metre
66 Supply, drawing, installation, testing and commissioning of following sizes of
PVC insulated and PVC sheathed copper conductor cable in the existing
surface / recessed steel conduit as required.
66.1 3 x 1.5 sq.mm. 300 Metre
Page 49 of 119
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.No DescriptionTotal
Qty.Unit Rate Rate In Words MR-Amount
Sub Head -XII: Integrated Building Management and Control System
A. Supply, installation, testing and commissioning of the following equipment
forming part of the integrated building management system complete with all
accessories and components required for proper functioning of the system
all as specified.
67 Supply, installation, testing and commissioning of Microprocessor UL listed
direct digital controller (DDC), 230 V, comprising of various AI, DI, AO and
DO conforming to input/output data point summary as specified. The
controller to be withinbuilt real time clock and peer to peer communication
capability and with 32 bit processors etc and complete in all respect as
required to make the system complete. The controller housing will be all as
per specifications and of approved makes. Suppliers requiring Supervisory
Control Devices necessary for connecting DDCs to Operator Work Station
shall include the cost of same in DDC controller as per specification. The
points in each DDC will be Analogue/Digital/Universal Inputs/Outputs as
required. Interchangability between one point type to another point type is
allowed with atleast I0% spare points of each set of clubbed points or
minimum one spare point for each clubbed point type over and above the
requirement. All relays etc. required for conversion of point typesm short
circuit current of 30 KA rms. The
i HVAC Plant Room for Chillers, Chilled water Pumps - Primary and
Secondary, Condensor Water Pumps, Hot Water Generators, Energy
Monitoring, BTU Metre (Modular DDCs with at least 105 I/O Points as
described in the I/O summary - AI-15, BI-58, AO-5, BO-27)
1 Set
ii Cooling Towers (Modular DDCs with at least 29 I/O Points as described in
the I/O summary - AI-5, BI-16, AO-0, BO-8) 1 Set
iii AHU (One Modular DDC per AHU with at least 9 I/O Points as described in
the I/O summary - AI-2, BI-3, AO-3, BO-1) 60 Sets
iv Normal and Smoke Ventilation System for Upper and lower Basement for
Centrifugal fans, Axial Fans, CO Level Monitoring, Energy Monitoring
(Modular DDCs with at least 124 I/O Points as described in the I/O summary-
AI-4, BI-80, AO-0, BO-40)
1 Set
Page 50 of 119
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.No DescriptionTotal
Qty.Unit Rate Rate In Words MR-Amount
v Pressurization Fans, Toilet Exhaust Fans and Lifts (Modular DDCs with at
least 22 I/O Points as described in the I/O summary- AI-0, BI-16, AO-0, BO-
6)
5 Sets
vi Fire Fighting System for Main, Sprinkler and Jockey Pumps, Diesel Engine
Driven Pump, Water Level Monitoring, Pressure Monitoring (Modular DDCs
with at least 37 I/O Points as described in the I/O summary- AI-15, BI-22,
AO-0, BO-0)
1 Set
vii DG Sets including Panels (Modular DDCs with at least 15 I/O Points as
described in the I/O summary- AI-3, BI-12, AO-0, BO-0) 1 Set
viii Electrical Sub station with Energy Monitoring (Modular DDCs with at least 5
I/O Points as described in the I/O summary- AI-0, BI-5, AO-0, BO-0) 1 Set
ix System Interface Unit for Integration of for Chillers, VFD in Secondary
Chilled Water pumps and AHUs, Multifuction meters, Automatic Analogue
Addressable Fire Detection and Alarm System.
1 Set
68 Supplying, installation and commissioning of Centrilized Graphical
Seamless integrated Building Management System as per specification with
1 client licences, Software must have Seamless integration with Automatic
Analogue Fire Detection and Alarm System, Chiilers, Multifunction meters,
VFDs, etc as mentioned in the I/O Summary as required.
1 Nos.
Page 51 of 119
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.No DescriptionTotal
Qty.Unit Rate Rate In Words MR-Amount
69 Supply, installation, testing and commissioning of Operator work station
complete as specified including following accessories.1 Sets
a) Operator work station with PC having Intel Core II Duo 2.4 GHz including
Serial ports (RS232) and USB ports and following accessories etc. all as
specified.
b) 2 Gigabyte of RAM memory
c) 160 Gigabytes of hard disk space
d) DVD Combo Drive
e) 21” LCD colour monitor
f) Optical Mouse with 2 Mouse Pads
g) Standard Key Board
h) Latest Windows Operating System (Windows 7)
i) 10/100 MBPS PCI LAN card.
70 Supply, installation, testing and commissioning of A4 size black laser printer
with all cables, software, hardware etc. complete in all respects. 1 No.
71 Supply, installation, testing and commissioning of 1000 VA UPS with a
maintenance free battery of Half hour backup at full load with all cables,
hardware etc. complete in all respects.
1 No.
Page 52 of 119
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.No DescriptionTotal
Qty.Unit Rate Rate In Words MR-Amount
72 Supply, installation, testing and commissioning of various electro
mechanical Field Devices and Sensors complete with all accessories etc. all
as per specifications.
a) Immersion Type Temperature Sensor 13 Nos.
b) Room Temperature Sensor. 60 Nos.
c) Differential Pressure Switch (air) 189 Nos.
d) Out side temp and Humidity sensor 2 Nos.
e) Differential Pressure Switch for water 18 Nos.
f) DC Voltage Transducers 4 Nos.
g) Electro magnetic flow meter
(i) 400 Dia 1 No.
(ii) 200 Dia 1 No.
h) Level switch (float type ) 4 Nos.
i) Flame proof level switch (Oil) 8 Nos.
j) Current Relay 5 Nos.
k) Water Flow Switch 17 Nos.
l) Water Pressure Transducer 8 Nos.
m) Level Transmitter 6 Nos.
n) CO Sensors for Basement 4 Nos.
73 Providing and fixing of G.I. pipes complete with G.I. fittings including
painting the pipes with two coats of anti corrosive bitumastic paint, trenching
and refilling etc. wherever required. (External work)
73.1 50 mm dia. Nominal bore 200 Meter
Page 53 of 119
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.No DescriptionTotal
Qty.Unit Rate Rate In Words MR-Amount
74 Supplying and drawing of following sizes of PVC sheathed copper conductor
cable in the existing surface / recessed steel conduit / PVC casing and
capping as required.
74.1 2 x1.5 sq.mm. 10000 Meter
74.2 3 x 1.5 sq.mm. 800 Meter
75 Supplying and drawing of PVC insulated and PVC sheathed copper
conductor twisted pair Shielded cable in the existing surface / recessed
PVC/steel conduit as required.
75.1 2 x1.5 sq.mm. 2000 Meter
76 Supply, drawing and laying CAT 6 cable in the existing surface / recessed
steel conduit, cable tray / surface as required.
76.1 CAT 6,UTP Cable 500 Meter
Sub Head -XIII: Audio Video System
DELEGATE UNIT
77Supplying ,installation and testing of The Basic Discussion Unit shall enable
participants to speak, register a request-to-speak and listen to the
speaker,Low susceptibility to mobile phone interference; Frequency
response 30 Hz – 20 kHz;Output power 2 x 15 mW/32 ohm
9 Nos
78Supply , fixing ,installation and testing of 18.9" Pluggable long microphone;
The pluggable microphone shall be an innovative, stylish and ergonomically
designed microphone with an adjustable stem, which simply plugs and
fasten directly into any unit;The microphone shall have a unidirectional
response for optimum performance even in noisy conditions, and shall
include an indicator that is red when the microphone is on and green when
the delegate unit is in the request state
9 Nos
Page 54 of 119
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.No DescriptionTotal
Qty.Unit Rate Rate In Words MR-Amount
CONTROL AND POWER SUPPLY UNIT
79Supply , fixing ,installation and testing of control and power supply unit
Include features for controlling delegate microphones,distributing
simultaneous interpretation and conducting,voting sessions, all without an
operator,connect upto 245 wired units
1 Nos
COMMON ITEMS (ACCESSORIES)
80 A rim shall complete the discussion units. A variety of rims with different
finishes shall be are available to allow matching with any interior; Silver
(RAL 9022),high gloss Silver (RAL 9022), Charcoal (PH 10736) ,High gloss
metal, Semi gloss metal (Set of 10 pieces)
1 Nos
81 The buttons for Chairman Discussion Units shall replace the single
microphone button on a Discussion unit when used in chairman mode.
These buttons shall also be useable for the Discussion unit in Auxiliary
control mode (Set of 10 buttons)
1 Nos
SOUND REINFORCEMENT SYSTEM
82 Supply , fixing ,installation and testing of feedback supressor which uses a
powerful DSP with a patented algorithm to suppress acoustic feedback
using an echo-cancellation and de-reverberation algorithm;Frequency
response 125 Hz to 15 kHz;Distortion <0.1 % @ 1 kHz; S/N > 90 dB; Signal
delay <11 ms
1 Nos
83 Audio Mixer amplifier 240W 1 Nos
84 Supply,installation and testing of the ceiling loud speaker with rated power of
6W,with 6w,3w,1.5w tappings,with Effective frequency range 80 to 18000
Hz, Sound pressure level at 6 W / 1 W (1 kHz, 1 m)
97 dB / 89 dB (SPL)
4 Nos
ELECTRICAL INTERNAL TOTAL
Page 55 of 119
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.No DescriptionTotal
Qty.Unit Rate Rate In Words MR-Amount
SUB HEAD - I - H.T. PANELS, TRANSFORMERS AND H.T. CABLES
1 HT PANEL (ONE INCOMING TWO OUTGOING PANEL BOARD)
Supplying, installation, testing & commissioning of indoor type floor mounted
metal clad, 11KV VCB panel with 3 Nos. VCBs, totally enclosed & fully
interlocked, horizontal drawout, horizontal isolation type breaker as per IS
13118, as amended up to date and additional specifications, having
capacities as mentioned below, single break, trip free mechanism,
motorised charged and auto/ manually closing breaker suitable for use on
11 KV, 3 Phase, 50Hz A.C. supply with short circuit fault level of 350 MVA,
complete with self contained fully interlocked, rack in and rack out
mechanism, air insulated but encapsulated copper bus bars of 630 Amps
capacity, breaker featured with mechanical ON/ OFF indicator with hand trip
device, spring release coil, shunt trip coil and auxiliary switch of 6 NO + 6
NC with computer compatible and equipped with following switchgears and
accessories i/c one earth truck, connections suitable for 3C x 240 sq.mm.
XLPE cable of 11KV grade (cable entry from bottom), power pack with 220
volt AC suitable for closing/ tripping/ indication of 3 nos. HT panel boards
with 2 nos. 12 volts each maintenance free batteries of suitable AH capacity
each (minimum 15minutes backup), charging unit, potential free contacts for
BMS compatability etc. complete as required.
A. Incoming - 1 No. 630Amp. VCB having following accessories.
1 set - 11KV/ 110 Volts PT Class 0.5 accuracy and 100 VA burden with 1
No. Voltmeter (0-15KV) digital type, selector switch for voltmeter and
protection Fuse / MCB for HT metering upto 12 KV on incomer.
1 set - Digital flush type class-0.5 accuracy multifunction meter with RS485
showing V, A, PF, KVA , KW, KWH etc.
1 set -Microprocessor based numerical relay with O/L , E/F and S/C
protection .
1 set - set of dual core dual ratio 3 CTs 100/ 50/5-5 A of 15VA burden and
accuracy Class- 0.5 for metering and class 5P10 for protection .LED indication lamps for R,Y,B, Breaker ON,OFF,TRIP, Trip circuit healthy,
spring charged, DC supply healthy, etc. as required.
B. Outgoing - 2 Nos. 630 A VCB each having following accessories.
i) Digital flush type class-0.5 accuracy multifunction meter with RS485
showing V, A, PF, KVA , KW, KWH etc. as required.
ii) Microprocessor based numerical relays with O/L, E/F & S/C protections .
iii) Set of dual core dual ratio 3 CTs 60/ 30/ 5/ 5 A of 15VA burden and
accuracy Class-0.5 for metering and class 5P10 for protection.
EXTERNAL ELECTRICAL
Page 56 of 119
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.No DescriptionTotal
Qty.Unit Rate Rate In Words MR-Amount
iv) LED indication lamps for R,Y,B, Breaker ON,OFF,TRIP, Trip circuit healthy,
spring charged, DC supply healthy, etc. as required.
v) Transformer protection release with 8 window annunciation each etc. as
required.
HT Panel (3 VCB) as above 1 Set
Page 57 of 119
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.No DescriptionTotal
Qty.Unit Rate Rate In Words MR-Amount
2 TRANSFORMER
2.1 Supplying of 750 KVA 11KV / 0.433KV, 3phase 50Hz, Dyn11, Indoor cast
resin dry type step down transformer having delta connection on primary
side and star connection on secondary side complete, including the cost of
making foundation and holding channels etc. as required at site.
2 Set
2.2 Installation, Testing and Commissioning of 750 KVA 11KV / 0.433KV,
3phase 50Hz, Dyn11, Indoor cast resin dry type step down transformer
having delta connection on primary side and star connection on secondary
side complete, including the cost of making foundation and holding
channels etc. as required at site.
2 Set
HT CABLING:
11 KV CABLE LAYING
3. Supply, laying, effecting proper connections, testing and commissioning of
the following sizes of 11 KV XLPE cable in RCC pipe or in trenches/cable
tray over a bed of sand and covering with bricks and as per specifications
including excavation of trenches and back filling complete as required.
3.1. 11 KV, 3C x 240 Sq. mm XLPE Aluminium cable 50 Meter
4. Hume Pipe:
Supply and installation of following sizes of hume pipes for road crossings,
paved areas, laying of HT cable etc, including collars, and misc jointing
accessories, digging the trench, back filling etc, making good the damages.
Complete in all respect as required (Pipe to be laid 1200 mm below ground).
4.1 200 mm dia 50 Meter
4.2 250 mm dia R.O. Meter
Page 58 of 119
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.No DescriptionTotal
Qty.Unit Rate Rate In Words MR-Amount
SUB HEAD - II - LT PANEL
5 1250 A, 415V, 50kA (Ics=Icu=Icw=50 KA for 1 second), TPN, EDO type,
Micro-processor based release (for over current and Earth fault protections)
FIX A.C.B. with all indications, metering, protections, push buttons etc.
complete in all respects and as required. (For 750KVA DG) with OUTDOOR
HOUSING
1 Set
6 1600 A, 415V, 50kA (Ics=Icu=Icw=50 KA for 1 second), TPN, EDO type,
Micro-processor based release (for over current and Earth fault protections)
FIX A.C.B. with all indications, metering, protections, push buttons etc.
complete in all respects and as required. (For 1010 KVA DG) with
OUTDOOR HOUSING
1 Set
7 MAIN LT PANEL (PLC based with Auto load sharing, auto
sharing,auto sharing, Load management system)
Design,fabrication,supplying,assembling, erecting, connecting, testing and
commissioning of dust,damp and vermin proof free floor standing sheet
steel enclosed non-drawout moduler type LT Main Panel, fabricated out of
suitable sized angle iron and flats, base channel and covered with 2.0mm
thick CRCA sheet, duly painted complete with earth bus, aluminium bus bar,
numbering & sign writing, interconnection & including the cost of connection
through bus bar / copper conductor flexible connection with necessary
interlocking with existing panel as shown in drawing as per specification and
mounted with the followings. Trafo and DG incomers alongwith buscoupler
shall be colour coded compartment.The Panel shall have IP-54 rating of
form-4.
Page 59 of 119
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.No DescriptionTotal
Qty.Unit Rate Rate In Words MR-Amount
INCOMER
a)
2 Nos.1250 A, 415V, 50 KA (Ics=Icu=Icw =50 KA for 1 second),4 Pole,
Electrical draw out type, Micro-processor based release (for over current,
Short circuit and Earth fault protections) A.C.B. with all indications,
metering, protections, push buttons etc. complete in all respects as
mentioned in specifications and as required. (For 2 Nos.Transformer 750
KVA)
Digital flush type class -I accuracy multifunction meter showing V, A, PF,
KVAR , KWH etc. with 3 Nos. current transformers of 1250/5 ratio, 15 VA
Class 1.0 metering.(each)
1 Set of three phase R,Y,B indicating lamps along with 2A SP MCB backup
protection.(each)
Control 2A MCB, control terminals & wiring as required.(each)
27-Undervoltage with definite time relay - 1 No(each)
b)
1No.1600 A, 415V, 50 KA (Ics=Icu=Icw =50 KA for 1 second),4 Pole,
Electrical draw out type, Micro-processor based release (for over current,
Short circuit and Earth fault protections) A.C.B. with all indications,
metering, protections, push buttons etc. complete in all respects as
mentioned in specifications and as required. (For 1 No.DG 1010 KVA)
Digital flush type class -I accuracy multifunction meter showing V, A, PF,
KVAR , KWH etc. with 3 Nos. current transformers of 1600/5 ratio, 15 VA
Class 1.0 metering.(each)
1 Set of three phase R,Y,B indicating lamps along with 2A SP MCB backup
protection.(each)
Control 2A MCB, control terminals & wiring as required.(each)
27-Undervoltage with definite time relay - 1 No(each)
Page 60 of 119
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.No DescriptionTotal
Qty.Unit Rate Rate In Words MR-Amount
1No.1250 A, 415V, 50 KA (Ics=Icu=Icw =50 KA for 1 second),4 Pole,
Electrical draw out type, Micro-processor based release (for over current,
Short circuit and Earth fault protections) A.C.B. with all indications,
metering, protections, push buttons etc. complete in all respects as
mentioned in specifications and as required. (For 1 No.DG 750 KVA)
Digital flush type class -I accuracy multifunction meter showing V, A, PF,
KVAR , KWH etc. with 3 Nos. current transformers of 1250/5 ratio, 15 VA
Class 1.0 metering.(each)
1 Set of three phase R,Y,B indicating lamps along with 2A SP MCB backup
protection.(each)
Control 2A MCB, control terminals & wiring as required.(each)
27-Undervoltage with definite time relay - 1 No(each)
Bus Coupler
1600 A, 415V (Ics=Icu=Icw 50 KA for 1 second), 4 Pole, EDO ACB
Electrically interlocked, with all indications, push buttons etc. complete in all
respects as mentioned in specifications and as required:-
1 Set of ON/Trip indicating lamps .
Bus Bar-1
2000A, TPN Aluminium Bus bar with extendable arrangment - 1 Set
Bus Bar-2
2000A, TPN Aluminium Bus bar for section-2 with extendable arrangment -
1 Set
INTERLOCKING
All Incoming ACB's/MCCB shall be electrically interlocked to achieve the
sequence of operation, in case of manual override mode.
OUTGOINGS:
Following rated 415V, MCCB's with overcurrent and short circuit releases,
all indication, front operating handle & door interlock with Multi Meter with
Volt, Amp and KWH etc. complete in all respects as mentioned in
specifications and as required For each outgoing:
OUTGOINGS:
1000A 35 KA 4P , MDO ACB - 2 Nos.
630A 35 KA 4P MCCB -6 Nos.
400A 35 KA 4P MCCB -5 Nos.
250A 35 KA 4P MCCB -4 Nos.
100A 35 KA 4P MCCB -8 Nos.
63A 35 KA 4P MCCB -4 Nos.
All ACB/MCCB should be IBMS compatible
MAIN LT PANEL as mentioned above 1 Set
Page 61 of 119
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.No DescriptionTotal
Qty.Unit Rate Rate In Words MR-Amount
8 CAPACITOR PANEL (275 KVAR)
Design, manufacture and supply of the following extensible cubicle type
indoor mounting Powder coated, modular compartmentalized IP 42, dust
and vermin proof, floor mounting 2 mm thick sheet steel clad switchboard
suitable for use at 415 volts 3 phase 4 wire 50 cycle system and to
withstand a symmetrical fault level of 35 MVA at 415 volts. (35 kA).
NOTE : The following provisions shall be required to be made in the
switchboard detailed below :-
The Switchboard shall have provision for entry of all XLPE/PVC AL
Armoured cables/bus duct from the top/bottom as required.
All live accessible parts shall be shrouded and all equipment shall be finger
touch proof. The busbar insulation shall be with heat shrinkable sleeves.
SMC/DMC shrouds and busbar supports shall be used.
Suitable tinned copper extension links for incoming/outgoing cables shall be
provided wherever required.
Control circuits includes breaker control switch, auto manual selector switch,
anti pumping relay, spring charging trip indication, TIMER, control wiring,
Auxiliary contactors MCB’s as required at site.
All the incomer breakers shall be interlocked with micro PLC’s to avoid
parallel operation. Stabilized separate power supply to be provided for micro
PLC.
All incomers having microprocessors breakers shall have neutral CT.
All fault level breaking capacity indicates shall be Ics value at 415 volts.
All MCCB shall have variable overload settings.
Space Heater/ light/ air filter shall be provided for each vertical
compartment.
Padlocking facility shall be provided on all outgoing feeders.
All ACB’s shall have all standard accessories such as CT’s, Arc Chute,
Safety Shutters etc.
All inter Panel wiring from PLC to DG / Transformer / Bus Couplers as
required.
Link and drops from ACB/MCCB shall be designed for full rated current of
ACB/MCCB ratings at same current density as of Main Bus Bar.
The ACB shall have LED indications to indicate type of fault.
Page 62 of 119
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.No DescriptionTotal
Qty.Unit Rate Rate In Words MR-Amount
CAPACITOR SWITCHBOARD (275 KVAR)
INCOMING
1NO 630 A 4P MCCB 35 KA with Microprosessor based release
3 Nos. Cast resin 630/5 Amp. Class 1.0, 15VA Burden C.T's for metering.
Square flush mounted 0-630 Amp Digial ammeter with 3 way & off selection
switch.
Three phase Iindicating Lamp.
Terminal to receive XLPE insulated cable.
11 Step automatic P.F. connection relay (microprocessor) to sense and
monitor the system power factor & provide impulses for operation of 12
sequential capacitor circuits.
Power Factor meter (Digital)
BUSBARS
Electrolytic high conductivity aluminium three phase busbars rated at
800Amp having a maximum current density of 1 amp per sq mm suitable to
with stand symmetrical fault level of 35 kA at 415 volts.
Page 63 of 119
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.No DescriptionTotal
Qty.Unit Rate Rate In Words MR-Amount
OUTGOING
4 Sets 125 A TP MCCB 35 KA Capacitor duty complete with followings
3 pole contactor 125 amp Capacitor duty suitable for automatic switching of
50 kVAR capacitor bank.
Indicating lamp to give status of the circuit.
Manual/auto switch.
50 kVAr hermetically sealed metallized polypropylene capacitor units (MPP-
S) complete with fuse protection, discharge resistors, interconnections etc
complete as required.
Set of push button stations red and green for manual operation of capacitor
unit with auto/manual selector switch.
1 Set 63 A TP MCCB 35 KA complete with followings
3 pole contactor 70 Amp Capacitor dutysuitable for automatic switching of
25 kVAR capacitor bank.
Indicating lamp to give status of the circuit.
Manual/auto switch.
25 kVAr hermetically sealed metallized polypropylene capacitor units (MPP-
S) complete with fuse protection, discharge resistors, interconnections etc
complete as required.
Push button stations red and green for manual operation of capacitor unit
with auto/manual selector switch.
1 Set 63 A TP MCCB 35 KA complete with followings
3 pole contactor 70 Amp Capacitor dutysuitable for automatic switching of
20 kVAR capacitor bank.
Indicating lamp to give status of the circuit.
Manual/auto switch.
20 kVAr hermetically sealed metallized polypropylene capacitor units (MPP-
S) complete with fuse protection, discharge resistors, interconnections etc
complete as required.
Push button stations red and green for manual operation of capacitor unit
with auto/manual selector switch.
2 Sets 32 A TP MCCB 35 KA Capacitor duty complete with followings
3 pole contactor 32 Amp Capacitor duty suitable for automatic switching of
10 kVAR capacitor bank.
Indicating lamp to give status of the circuit.
Manual/auto switch.
10 kVAr hermetically sealed metallized polypropylene capacitor units (MPP-
S) complete with fuse protection, discharge resistors, interconnections etc
complete as required.
Page 64 of 119
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.No DescriptionTotal
Qty.Unit Rate Rate In Words MR-Amount
Push button stations red and green for manual operation of capacitor unit
with auto/manual selector switch.
2 Set 32 A TP MCCB 35 KA Capacitor duty complete with followings
3 pole contactor 32 Amp Capacitor duty suitable for automatic switching of
5 kVAR capacitor bank.
Indicating lamp to give status of the circuit.
Manual/auto switch.
5 kVAr hermetically sealed metallized polypropylene capacitor units (MPP-
S) complete with fuse protection, discharge resistors, interconnections etc
complete as required.
Push button stations red and green for manual operation of capacitor unit
with auto/manual selector switch.
The switchboard shall be complete with all interconnections, risers, internal
wiring, labels etc complete as required.
Capacitor Panel Described as above 2 Sets
Page 65 of 119
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.No DescriptionTotal
Qty.Unit Rate Rate In Words MR-Amount
SUB HEAD III - Cable, End Termination & Cable Trays
9 Supply & laying testing and commissioning of following sizes of XLPE
insulated PVC sheathed aluminium conductor armoured cable of 1.1 KV
grade on existing cable tray / surface including saddle, clamps etc. complete
as required.
9.1 3½ x 300 Sqmm. 450 Mtr.
9.2 3½ x 240 Sqmm. 50 Mtr.
9.3 3½ x 185 Sqmm. 225 Mtr.
9.4 3½ x 150 Sqmm. 150 Mtr.
9.5 3½ x 120 Sqmm. 400 Mtr.
9.6 3½ x 70 Sqmm. 100 Mtr.
9.7 3½ x 50 Sqmm. 160 Mtr.
9.8 3½ x 35 Sqmm. 30 Mtr.
10 Fabricating and installing follwoing size of ladder type M.S. cable trays
including horizontal and vertical bends, reducers, tees, cross members and
other accessories as required and duly suspended from the ceiling with M.S.
suspenderes and icnluding painting with powder coating etc. as required:
10.1 150 mm. Width x 50mm Depth x 1.6 mm Thickness 60 Mtr.
10.2 300 mm. Width x 50mm Depth x 1.6 mm Thickness 60 Mtr.
10.3 450 mm. Width x 75mm Depth x 2.0 mm Thickness 40 Mtr.
10.4 600 mm. Width x 75mm Depth x 2.0 mm Thickness 50 Mtr.
Page 66 of 119
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.No DescriptionTotal
Qty.Unit Rate Rate In Words MR-Amount
SUB HEAD - IV - EARTHING
11. Supply and Installing earthing stations at locations as called for with 600 x
600 x 6.3 mm. thick G.I Plate electrode 20 'mm. dia medium class GI pipe
(Indian Tube Company make or approved equal), GI funnel with 20 gauge
GI wire mesh masonry chamber with concrete base, CI manhole cover with
frame (300 mm. x 300 mm.) and bitumastic paint and packing the mixture of
Charcoal and salt around plate electrode complete as per IS: 3043). - (For
Body Earthing of HT Meter, HT Panel, Transformers, LT Panel & DG Sets)
14 Nos
12. Supply and Installing earthing stations at locations as called for with 600 x
600 x 3.15 mm. thick Copper Plate electrode 20 'mm dia medium class GI
pipe (Indian Tube Company make or approved equal), GI funnel with 20
gauge GI wire mesh masonry chamber with concrete base, CI manhole
cover with frame (300 mm. x 300 mm.) and bitumastic paint and packing the
mixture of Charcoal and salt around plate electrode complete as per IS:
3043). - (For Neutral Point Earthing of Transformers & D.G. Sets.)
8 Nos
13. Supply and fixing in position the following G.I./Copper tape/wires including
providing all fixing accessories and effecting proper connections.
13.1. 50 mm. x 6 mm. Cu. tape (for Trafo. & DG Neutral) 120 RM
13.2. 50 mm. x 6 mm. G.I. Tape (for Trafo & DG body) 120 RM
13.3. 25 mm. x 6 mm. G.I. tape 200 RM
13.4. 32 mm. x 6 mm. G.I. tape 100 RM
14 Providing and fixing 8 SWG dia GI wire on surface or in recess for loop
earthing along with the existing surface / recessed conduits / submain wiring
/ cable as required.
400 RM
Page 67 of 119
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.No DescriptionTotal
Qty.Unit Rate Rate In Words MR-Amount
SUB HEAD V - DG SETS
15 DG SETS 1010KVA
Supply, installation, testing and commissioning of Silent Type Diesel
Generating Set of 1010 KVA, 3 phase & neutral, 50 c/s. 415 A.C. rating,
comprising of following Diesel Engine, Alternator, Sound Attenuated
Acoustic Enclosure, necessary RCC foundation as per manufacturers
standards for erection as required and with all other associated accessories
as per specifications & as required:
A. DIESEL ENGINE:
Type: Multi-cylinder water cooled with direct radiator, Turbo charged with
charged air cooling.
No. of strokes : 4
Fuelinjection :Direct / Electronic
Maximum speed : 1500 RPM
Rated power : 1180 BHP (minimum)
Cooling system : Water cooled Cylinders with Radiator
Starting system : Battery starting.
Govering system: Electronic/ digital governer
B. ALTERNATOR;
Type : Brushless.
Actual Power 1010 KVA at 50 deg C.
Rated power : as per standards (at 40 deg C)
Frequency : 50 Cycles/sec.
Supply system :3 phases & neutral
Connection : Star.
Rated voltage: 415 Volts.
Rated rpm. : 1500 rpm. max.
Casing : As per IP-23 protection
Insulation : Class `H'.
Voltage : Automatic/Digital voltage regulator
Power factor : 0.8.
Controller : PCC 3.3 / WOODWARD / DEIF or equivalent
Page 68 of 119
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.No DescriptionTotal
Qty.Unit Rate Rate In Words MR-Amount
C. ACCESSORIES:
The Diesel Engine shall be equipped with minimum following/ as indicated
in the specifications, devices/ accessories built-in type including all
standard fittings.
Fuel supply pump with manual venting pump.
Engine driven or electric motor driven Radiator
Turbo charger with air filter (dry/ oil bath type) and damper.
Charge air cooler.
Suction fuel filter
Lube oil filter.
Hourmeter and RPM indicator.
Battery Starting Mechanism.
Instrument/Indication panel complete with all accessories as per
specifications
Control devices for safety and monitoring alongwith indicators.
D.OTHER ACCESSORIES/EQUIPMENT
MS fabricated Common base/ foundation frame.
spring type vibration isolators
Fly wheel and flexible coupling.
Automatic/Digital voltage regulator
Day storage tank for 990 ltr capacity fabricated with 3 mm thick MS sheet,
high & low level indicator and alarm contacts etc. as required.
Residential type silencer & catalytic converter , SS braided rubber
expansion bellows/ joints, etc. as required.
Necessary batteries ( minimum 2 of 180 AH capacity) with leads and battery
stand etc.
initial charge of lubricants, coolant etc
All the above (except Day Oil tank) housed in a suitable CPCB Approved
Accoustic enclosure for noise limits of thickness not less than 16SWG
CRCA sheet steel etc. complete as required.
Page 69 of 119
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.No DescriptionTotal
Qty.Unit Rate Rate In Words MR-Amount
MR Diesel Generating set (1010 KVA) as described above. 1 Set
16 Providing and fixing in position exhaust pipe of following dia welded black
MS pipe conforming to IS: 3589 cut to required lengths and installed with
necessary bends, supports and clamps, anti-vibration mounting, SS braided
Rubber expansion bellows, insulation of exhaust system with 50 mm thick
mineral wool/ Rockwool of density not less than 120 kg/ cu.m, covered with
0.6mm thick Aluminium cladding, necessary supporting structure (angles &
channels), foundation for supporting structure etc. as required.
16.1 350 mm dia (5.2mm thick) 40 mtrs.
17 Providing and fixing in position following size of heavy duty stainless steel
flanged expension bellows for DG exhaust piping complete with GI nut bolt
washers etc. as required.
17.1 350 mm dia 1 nos.
18 Providing & fixing for MS support structure for exhaust fume pipes from DG
Sets (Exhaust pipe to be measured and paid for separately) along horizontal
and vertical runs upto the height (as per CPCB norms) including cutting,
welding etc and applying two coats of red oxide and two coats of synthetic
enamelled paint of colour and shade as directed by consultant. The design
of the support structure shall be done by the contractor and shall be as per
CPCB norms approved , also to get the approval from the client/ consultant
before execution etc. as required.
2500 Kg
Page 70 of 119
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.No DescriptionTotal
Qty.Unit Rate Rate In Words MR-Amount
SUB HEAD VI - RISING MAINS
19 RISING MAINS FOR LIGHT / POWER
Supplying, Installation on wall, Testing & Commissioning of pre fabricated
sandwiched/conventional type insulated Rising Main with Tap off unit facility
with metal clad enclosure of minimum 1.6 mm thick Aluminum of following
capacities, as per IS 8623, TEC 439 suitable for 415/500 Volt 3 Phase 4
wire (with 100 % Neutral +E+E) 50Hz AC supply system of aluminium bus
bars complete with flange end, elbow, expansion joints, fire barriers, copper
flexible end connections at both ends. i/c necessary supports including
suitable Reducer joint as required etc. as per specifications attached as
required.19.1 630 Amps (SC rating for 1sec. - 35kA) 30 Mtrs.
19.2 400 Amps (SC rating for 1sec. - 35kA) 30 Mtrs.
20 END FEED UNIT (ADOPTER BOX)
Supply, installation, testing & commissioning of factory fabricated "Adopter
Box" of 2.0 mm thick CRCA Sheet including supply and fixing following
switch gears complete with stands, incomming cable / bus trunking end box,
brass compression gland, interconnection, eathing etc. complete as per
specification and as required.
20.1 630 Amps with TP MCCB with Breaking capacity 35kA 1 No.
20.2 400 Amps with TP MCCB with Breaking capacity 35kA 1 No.
21 TAP-OFF BOXES
Supply, installation, testing & commissioning of factory fabricated, TP Tap
off unit box of 1.6mm thick CRCA/Aluminum sheet of following capacity on
the existing sandwitch type insulated rising mains and supplying and fixing
following switchgears and accessories complete with, interconnections,
earthing etc. as required.
21.1 63Amps, TP MCCB 35 kA 7 Nos.
21.2 100Amps, TP MCCB 35 kA 8 Nos.
21.3 160Amps, TP MCCB 35 kA 4 Nos.
Page 71 of 119
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.No DescriptionTotal
Qty.Unit Rate Rate In Words MR-Amount
SUB HEAD VII - EXTERNAL LIGHTING
22 External Lighting Feeder Pillars:
Supply, assembly, erection, connecting, testing & commissioning of LT
weather proof dust and vermin proof, outdoor feeder pillar, fabricated out of
suitable sized angle iron and flats and covered with 3mm thick CRCA sheet
steel including canopy, duly stove enamel painted, both sides (front and
rear) openable with locking arrangement, rubber gasket cable glands, etc.
Bakelite phase separators and bus bar supports including RCC 1:2:4 (1
cement: 2 coarse sand : 4 graded stone aggregate 20mm nominal size)
foundation, 450 mm deep and 150 mm above the ground. The feeder pillars
shall be complete with 3 phase and neutral bus bars of capacities as
described below and moulded case circuit breakers (MCCBs) with
adjustable overload relay (including ON indication for MCCB to be
provided), copper FRLS control wiring with 1.5sq.mm, complete in all
respects as per specifications as required.
INCOMING:-
63A 4P MCCB (25ka) with thermal magnetic release & rotary handle - 1no.
3 Phase and neutral (100%N) aluminium bus bars of 100/ 150 amps.
Capacity.
OUTGOING:-
70 AMP. TP CONTACTOR WITH NO/ NC CONTACTS -1 set.
24 HOUR TIMER - 1 set.
20A 4P MCB (10ka) - 2 nos.
a) 16A DP MCB (10ka) - 5nos.
63A 4P MCB (10ka) - 1nos.
b) 16 AMP. SWITCH & SOCKET - 1 no. with in the feeder pillar.
External Lighting Feeder Pillar as above 1 Set
Page 72 of 119
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.No DescriptionTotal
Qty.Unit Rate Rate In Words MR-Amount
23 Supply of standard 7.5 metre high (above ground) hot dip galvanized
(grading of galvenisation average 70 micron or better as per IS2629 or
equivalent) octagonal pole, as per IS 875 Part-3, with stiffener, chain, allen
bolt, single arm bracket, foundation bolt, anchor plate, template, nut and
washers galvanized, factory finish base plate of size 220 x 220 x 12 mm etc
complete as required. The pole shall be made of 3 mm thickness sheet with
tolerance of +/- 5%. The column shall also be provided with flush door at the
bottom with proper strengthening to the cutout of the door opening, a
junction/ looping box with Heavy duty 3 phase, 32 Amp connector with 16A
DP MCB including all accessories complete as required. (make & model will
be selected by the client).
10 Nos.
24 Supply of solar power Street Lighting Fixture complete with 7.5 meter long
Octaganol GI poles as per approved makes and as per standard design.
The luminaire shall be of aluminium die cast construction with minimum
IP65 protection with inter-connection copper cable from solar panel to
battery, to controller and to luminaire etc as required.
The storage capacity of the battery should be sufficient to run the full load
for 18 hours on rainy/ heavy cloudy days.The unit should also have an
additional AC charging arrangement to charge the batteries in case of very
long heavy cloudy days
A junction chamber of size 300mm/ 100mm with cable termination
arrangement connector block and 1 No. 10 Amp SPMCB shall be provided.
The street light fixture shall be 1 x 70 watt capacity with LED bulbs of white
colour of 1 watt each. the fixture shall be complete with control gear for auto
switching ON, switching OFF supplementary power charging in case of non
availability of solar power on very long heavy cloudy days etc. as required.
The solar panel shall be of sufficient capacity to charge the sealed
maintenance free battery of minimum 160 AH capacity. The RCC pedestral
shall be made of 1:2:4 ratio as required.
The column shall be smooth surface finished degreased, derusted, primary
coated, cavity sealed and painted with PU based self curing polyurethane
based automotive paint. Complete item will be finalised by the client/
consultant.
4 Nos.
Page 73 of 119
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.No DescriptionTotal
Qty.Unit Rate Rate In Words MR-Amount
25 Receiving, Assembly, Erection, Testing & Commissioning of Street
Lighting Fixture complete with 7.5 meter long octagonal GI pole with single
arm bracket, base plate, including RCC foundation as per standard design &
approved by the consultant/ client etc. as required.
10 Nos.
26 Receiving, Assembly, Erection, Testing & Commissioning of Solar
Street Lighting Fixture complete with 7.5 meter long octagonal GI pole
single arm bracket, base plate, bttery box, including RCC foundation as per
standard design & approved by the consultant/ client etc. as required.
4 Nos.
27 Supply of following luminaries (IP-65) with housing made of single piece
high pressure die cast alluminium alloy/ as per standards, energy efficient
copper ballast, heat resistant toughened flat glass / cover glare free, pole
mounting mechanism etc. (make & model will be approved by the client).
27.1 150 watt Street light fixture 10 Nos.
27.2 Bollard, Floor Mounted with Fixed light distribution suitable for CFL Lamp24 Nos.
28 Supply, laying, testing and commissioning of 1.1 kv grade XLPE insulated
PVC sheathed steel armoured alluminium stranded conductor LT Cables
including both end termination with lugs & brass glands in trenches/ ducts/
through RCC pipes under roads of following sizes, complete all as specified
(as per CPWD specifications for External Electrical works) including the cost
of digging and back filling the trenches, sand filling, brick covering for
protection etc complete as required & approved by Engineer's Incharge.
(Tagging to be provided with aluminium strips on both the ends as
approved).28.1 4 core X 10 Sq.mm (For external Lights) 250 Meter
28.2 4 core X 6 Sq.mm (For external Lights) 100 Meter
29 Providing, laying, fixing, connecting and testing of undernoted sizes of
copper strip/ GI strip/ wire from earth electrode to equipment loop and
earthing system, in trenches, on surfaces, along pole or along M.S. support,
etc. including excavation where required for laying the copper strip/ GI strip
and filling back complete, conforming to relevant IS and all as specified.
29.1 G.I. wire 6 SWG on surface or in recess 80 Meter
29.2 GI strip 25mmx 5mm on surface or in recess 10 Meter
ELECTRICAL EXTERNAL TOTAL
Page 74 of 119
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.No DescriptionTotal
Qty.Unit Rate Rate In Words MR-Amount
Sub Head - I - (Wet Riser System - Pumping Equipments )
1 Supply, Installation, Testing and Commissioning of Electric Driven Main
Fire Pump suitable for auto operation & consisting of following: complete in
all respect as required.
a) Horizontal Split casing type, centrifugal, multistage, pump of cast iron body
and bronze impeller with stainless steel shaft, mechanical seal to ensure a
minimum pressure of 3.5 kg/sq. cm. at highest and farthest outlet at
specified flow of 2850 lpm at 95 Mtr. head confirming to IS 1520.
b) Suitable HP (Minimum 85 hp) squirrel cage induction motor, TEFC
synchronous speed 1500 RPM (with permissible slip), suitable for operation
on 415 volts, 3 phase 50 Hz. AC with IP 55 protection for enclosure,
horizontal foot mounted type with Class-' F' insulation, confirming to IS-325.
c) Common base frame fabricated out of M.S channel of suitable size, flexible
coupling, coupling guard, foundation bolts and pressure gauge with valve
etc. Suitable cement concrete foundation duly plastered, with anti vibration
pads etc. complete as per manufacturer's design & standards and as per
detailed specifications.
2 Set
2 Supply, Installation, Testing and Commissioning of Diesel Engine Driven
Main Fire Pump suitable for auto operation and consisting of following:
complete in all respect as required.
a) Horizontal Split casing type, centrifugal, multistage pump of cast iron body
and bronze impeller with stainless steel shaft, mechanical seal to ensure a
minimum pressure of 3.5 kg/sq.cm. at highest and farthest outlet at
specified flow of 2850lpm at 95 Mtr. head confirming to IS 1520.
FIRE FIGHTING
Page 75 of 119
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.No DescriptionTotal
Qty.Unit Rate Rate In Words MR-Amount
b) Suitable HP(Minimum 85 BHP) 1500 RPM, 4 stroke, cold starting type
Diesel Engine with Heat Exchanger confirming to relevant BIS & IS
Standards, complete with all required accessories / system, fuel oil filter,
lubricant oil pump with filter, 2 Nos. starting batteries of 180 AH capacity
each with suitable angle iron stand, engine starting panel having all the
controls meters, gauges, tachometer, hour meters, starting switch with keys
for manual starting, auto starting mechanism, 24 Volts electric starting
equipment, Diesel Tank for 8 hrs continuous running of diesel engine,
having minimum capacity of 200 Ltrs. (tank made out of 3mm thick M.S.
Sheet with filling Cap, drain Cock, diesel indicator duly mounted on M.S.
angle) exhaust pipe of minimum 30 Metre length, duly insulated with 50
mm. thick glass wool with 1.0 mm. thick aluminium sheet cladding, exhaust
residential silencer, stop solenoid for auto stop in the event of fault with
audio indications, painted with post office red colour etc. as required.
c) M.S. fabricated Common base frame, flexible coupling, coupling guard,
foundation bolts and pressure gauge with valve etc. Suitable cement
concrete foundation duly plastered, with anti vibration pads etc. complete as
per manufacturer's design & standards and as per detailed specifications.
1 Set
3 Supplying, Installation, Testing and Commissioning of Electric Driven
Pressurization Pump (Jockey Pump) suitable for auto operation and
consisting of following: complete in all respects as required.
a) Horizontal type, centrifugal end suction type pump of cast iron body and
bronze impeller with stainless steel shaft, mechanical seal, gland packing
and flow of 180 Ipm at 95 Mtr. head confirming to IS:1520.
b) Suitable HP (Minimum 10 HP) squirrel cage induction motor TEFC type
2900 RPM suitable for operation on 415 volts, 3 phase 50 Hz. AC with IP 55
class of protection for enclosure, horizontal foot mounted type with Class -'F'
insulation, confirming to IS:325.
Page 76 of 119
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.No DescriptionTotal
Qty.Unit Rate Rate In Words MR-Amount
c) Common base frame fabricated out of M.S channel of suitable size, flexible
coupling, coupling guard, foundation bolts and pressure gauge with valve
etc. Suitable cement concrete foundation duly plastered, with anti vibration
pads etc. complete as per manufacturer's design & standards and as per
detailed specifications.
1 Set
4 Fabricating, Supplying, Installation, Testing and Commissioning Air Vessel
of continuous welded construction with flanged discharge header on the top
of each riser fabricated out of 10 mm thick dished ends and 8 mm thick MS
sheet, Air Release Valve complete with suitable drain arrangement with 25
mm dia gun metal wheel valve complete with all accessories etc. as
required of the following sizes
4.1 1.2 Meter high and 250 mm dia 0 Each
5 Fabricating, Supplying, Installation, Testing and Commissioning Air Vessel
of continuous welded construction with flanged discharge header in pump
house fabricated out of 10 mm thick dished ends and 8 mm thick MS sheet,
Air Release Valve, complete with drain arrangement with 25 mm dia gun
metal wheel valve complete with all accessories etc. as required of the
following sizes 5.1 2 Meter high and 450 mm dia suitable to operate Jockey Pump, Main Fire
Pump & Diesel Engine Driven Fire Pump1 Each
6 Supply, Installation, testing and commissioning of pressure switches for
Hydrant / Diesel Engine Driven Pump / Jockey Pumps, diaphragm type,
adjustable range from 0-9 bar and a regulation range of 0.1 1.5 bar direct
mounted SNAP acting type made from die cast aluminium with epoxy
powder coated finish and SS316 diaphragm and other wetted parts,
including necessary wiring upto control panel & other materials as required
as per specifications.
4 Each
Page 77 of 119
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.No DescriptionTotal
Qty.Unit Rate Rate In Words MR-Amount
Sub Head - II - (Hydrants System)
7 Supplying and fixing Single Headed Internal Hydrant Valve oblique pattern
with instantaneous Stainless Steel coupling of 63 mm dia with cast iron
wheel ISI marked, conforming to IS : 5290 (Type A), with 80 mm dia flanged
inlet, with ABS cap and chain complete with all accessories etc. as required.
22 Each
8 Supply, Installation, Testing and Commissioning 100% synthetic flax
canvas Non-percolating FIRE hose (Type A), I.S.I marked 63mm dia x
15m long with stainless steel male & female couplings (ISI marked) bound
& riveted to hose pipes with copper rivets and copper wire as required.
44 Each
9 Supplying and fixing Stainless Steel branch pipe with 20mm dia nozzle
conforming to IS:903. suitable for installation connections to hose coupling
etc. as required.
27 Each
10 Supplying and Fixing First Aid Hose Reel, wall mounting swinging type
complete with drum & bracket of MS construction, spray painted in Post
office Red, confirming to IS 884/1995 with upto date amendments, complete
with the following as required.
(a) 36 Meter long 20 mm dia water hose Thermoplastic (Textile reinforced)
Type - 2 as per IS : 12585
(b) 25 mm dia gun metal ball valve & nozzle.
(c) Drum and brackets for fixing the equipments on wall.
(d) Connection from riser with stop valve (gun metal) & M.S. Pipe 22 Each
Page 78 of 119
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.No DescriptionTotal
Qty.Unit Rate Rate In Words MR-Amount
11 SITC weather proof M.S cabinet size 1200 mm x 2100 mm x 800mm
Supplying, installation, testing and commissioning of weather proof M.S
cabinet size 900 mm x 2100 mm x 600mm deep fabricated from 1.6mm
thick M.S. sheets and M.S angle 40mmx40mmx6mm complete with glass,
locking arrangements to accommodate the following: -
a) Gunmetal single headed Hydrant valve - 1 No.
b) Fire Hoses 63mm, 15 M long with accessories - 2 Nos.
c) Short branch - 1 No.
d) First Aid hose Reel - 1 No.
e) Fire Extinguisher - 2 Nos.
f) Fireman's Axe - 1 No.
g) Pressure Gauge - 1 No.
The cabinet shall be painted with one coat of primer and 2 coats of
synthetic enamel paint of approved shade.22 Each
12 Providing and fixing single gunmetal suction collecting head as per IS:
904-1983, hose coupling (draw out connection) with female outlet as per
903 complete with 150 mm dia. G.I. Suction pipe (with puddle flange) with a
foot valve with strainer complete as per drawings.
2 Each
13 Providing and Fixing 15 mm dia gunmetal / brass quartzoid type Sprinkler
Head with quartz bulb and set to operate at specified temperature.
13.1 Upright, 68° C, Chrome plated 1555 Each
13.2 Pendent, 68° C, Chrome plated 607 Each
13.3 Side wall type, 68° C, Chrome plated 21 Each
SITC of sprinkler installation valve
14 Supplying, Installation, Testing and Commissioning of Sprinkler installation
valve with water gong, pressure gauge, drain valve etc as required 200 mm
dia size etc. complete as required.
1 Each
15 Supplying and fixing vane type water flow switch suitable for installation on
50 mm to 150 mm dia line for a service pressure upto 20 kg/sq. cm. of
Potter / System sensor /Angus
19 Each
16 Supplying and fixing 4 way 63 mm instantaneous Fire Brigade Inlet
Connection (FBIC) comprising of gunmetal body and gunmetal
instantaneous male inlet coupling confirming to IS:904 with plug and cap
with chain as required with nuts & bolts and high pressure rubber gasket,
suitable for 150 mm dia MS pipe connection etc. complete as required.
1 Each
Page 79 of 119
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.No DescriptionTotal
Qty.Unit Rate Rate In Words MR-Amount
Page 80 of 119
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.No DescriptionTotal
Qty.Unit Rate Rate In Words MR-Amount
Sub Head - III - (Piping, Valves and Accessories)
SLTC of M.S pipe on surface
17 Supplying, laying, fixing, testing and commissioning of following sizes (NB)
of ISI marked heavy class M.S. pipes including cutting, threading, welding
etc. and providing all fittings e.g. elbows, reducers, clamps, hangers,
flanges, gaskets, nuts, bolts and washers etc. including painting of pipes
and fittings with red paint over a coat of ready mixed primer, both of
approved quality and shade including cutting holes and chases in brick or
RCC walls/slabs and making good the same etc. complete in all respect as
required.17.1 200 mm dia (6mm thick) 20 Metre
17.2 150 mm dia 579 Metre
17.3 100 mm dia 1046 Metre
17.4 80 mm dia 262 Metre
17.5 65 mm dia 631 Metre
17.6 50 mm dia 810 Metre
17.7 40 mm dia 374 Metre
17.8 32 mm dia 605 Metre
17.9 25 mm dia 4097 Metre
18 Providing & fixing of heavy class class M.S . pipes conforming to IS: 1239
complete with fittings including trenching and refilling etc. (external work)
including all fittings and accessories like tees, elbows, flanged joints, rubber
insertion, nuts, bolts or cutting and welding joints. Cost shall be inclusive of
excavation, dewatering, backfilling, ramming surrounding the pipe alround
with minimum 150 mm thick compacted silver sand and providing thrust
block at distance specified as per specifications. (Pipe shall be provided with
anti crossive protective treatment confirming to IS: 10221 standard complete
as per specification). All work complete as per specification and as directed
by Engineer-In-Charge. (All the fitting i.e. tee /elbow etc. for Valve
connections etc. will be flanged joints)
18.1 150 mm dia 650 Meter
18.2 80 mm dia 12 Meter
Page 81 of 119
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.No DescriptionTotal
Qty.Unit Rate Rate In Words MR-Amount
19 Supplying, Installation, Testing and Commissioning of Butterfly valves of
PN 1.6 rating of following sizes with nitrile Bronze / G.M. seat duly ISI
marked and stainless steel stem with lever/gear operation and cast iron
body in powder coated finish for fire fighting application complete in all
respects confirming to IS: 13095 as required.
19.1 150 mm dia 15 Each
19.2 100 mm dia 8 Each
19.3 80 mm dia 5 Each
19.4 65 mm dia 1 Each
20 Providing, Installation, Testing and Commissioning of double flanged cast
iron Non-Return Valve, PN 1.6 of following sizes confirming to IS : 5312
complete with rubber gasket, Gl bolts, nuts, washers etc. as required.
20.1 150 mm dia 11 Each
20.2 50 mm dia 1 Each
21 Providing, Installation, Testing and Commissioning of Gun Metal Ball
Valves with brass body chrome plated of following sizes as required.
21.1 40 mm dia 19 Each
21.2 50 mm dia 0 Each
Page 82 of 119
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.No DescriptionTotal
Qty.Unit Rate Rate In Words MR-Amount
22 Supplying and Fixing Orifice Plate made of 6 mm thick, upto 200 mm outer
dia. stainless steel with orifice (internal dia.) of required size in between
flange & landing valve of external and internal hydrant to reduce pressure to
working pressure of 3.5 Kg / cm2
complete as per specifications as required.
41 Each
23 Supply, Installation, Testing and Commissioning of 150 mm dia Bourden
type, Stainless Steel dial type Pressure Gauge including brass isolation
valve and siphon pipe having calibration of 0 - 16 Kg / cm2 . 26 Each
24 Supplying, Installation, Testing and Commissioning of CI body flanged (both
ends) type serviceable suction / Y strainer with (stainless steel / brass
mesh) conforming to relevant IS specifications amended upto date complete
including providing and fixing nuts, bolts, washers, gaskets etc. complete as
required.24.1 150 mm dia 3 Each
24.2 65 mm dia 1 Each
25 Supplying and Fixing of Fire Man's axe with heavy insulated rubber as per
standard conforming to IS 92622 Each
26 Providing and fixing of Cast Iron Rising Spindle Gate Sluice valve PN 16
(Flanged) rating hand wheel operated, stain less steel stem with gun metal
parts, Nut, bolts & washers etc.complete as required as per specification.
26.1 65 mm dia 2 Each
26.2 150 mm dia 9 Each
26.3 200 mm dia 1 Each
Page 83 of 119
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.No DescriptionTotal
Qty.Unit Rate Rate In Words MR-Amount
27 Providing & fixing double flanged Metallic expansion with M.S. fixed flanges
(PN-1.6) joint (suitable for system test pressure) of standard length as per
manufacturers specs including rubber gaskets, flanges, nuts, bolts and
washers complete as required as per specifications.
27.1 65 mm dia 2 Each
27.2 150 mm dia 8 Each
28 Providing & fixing controlled percolation fire hose pipe (as per IS:8423) of 63
mm dia and 15 meter length rated for brust pressure of 3.5 Kg/sqcm. The
hose shall be tested for flame resistance test in accordance to IS:8423.
Hose shall be complete with ISI marked SS male & female coupling (IS:903)
bound & riveted to hose pipe with copper rivets & 1.5 mm copper wire as
required as per specifications. (Location : External fire hydrant)
10 Each
29 Providing and fixing weather proof lockable cabinet of size not less than
0.9 x 0.6 x 0.5 mtr made out of MS sheet 2mm thick having central opening
and 6 mm thick glazed glass doors (Two nos.) suitably marked on the
outside with the letters "FIRE HOSE" including necessary locking
arrangement and shall be painted with one coat of primer and two coats of
synthetic enamel paint of approved shade as required as per specifications.
5 Each
30 Supply, Installation, Testing and Commissioning External Yard Hydrant
Stand Post comprising of MS pipe 80 mm dia (heavy duty C class) from
existing ringmain to about 1 meter above ground level and Single Headed
Yard Hydrant Valve with 80 mm dia flanged inlet, intantanneous SS
coupling of 63 mm dia with cast iron wheel ISI marked, conforming to IS :
5290 (Type A), with ABS cap and chain etc.complete with all accessroies as
required.
5 Each
Page 84 of 119
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.No DescriptionTotal
Qty.Unit Rate Rate In Words MR-Amount
Sub Head - IV - (Fire Extinguishers)
31 Supply, installation, testing and commissioning of ISI marked (IS:15638)
portable chemical fire extinguisher, water (gas pressure) type capacity 9
litres with gun metal cap and nozzle and complete in all respects including
initial fill and wall suspension brackets as required as per specifications.
22 Each
32 Providing and fixing fire extinguisher of carbon dioxide type consisting of
brand new high pressure steel cylinder bearing IS: 7285 mark and having
the approval of controller of explosives Nagpur, wheel type valve bearing
IS:3224 mark internal discharge tube, 1 meter long high pressure discharge
hose, non conducting horn, suspension bracket, fully charged bearing IS:
making fixed to wall as directed.
32.1 4.5kg capacity cylinder 22 Each
Page 85 of 119
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.No DescriptionTotal
Qty.Unit Rate Rate In Words MR-Amount
Sub Head - V (Motor Control Panels)
33.0 Fire Fighting Panel
Supplying, assembling, erecting, connecting, testing and commissioning of
dust, damp and vermin proof free floor standing factory built sheet steel
enclosed non-draw out modular type Fire fighting Panel fabricated out of 2.0
mm thick CRCA sheet hinged doors of 1.6mm thick CRCA sheet, duly
painted complete with earth bus, aluminium bus bar, numbering & sign
writing, interconnection & including the cost of connection through bus bar /
copper conductor flexible connection with necessary interlocking with
existing panel as shown in drawing as per specification and mounted with
the followings.
including control wiring with 1.5sqmm. & 2.5sqmm. PVC insulated FRLS
copper conductor S/C cable for voltage & current respectively, cable alleys,
cable gland plates in two half, etc. necessary metering protections &
indications etc. complete as required. ( Each starter should have remote
control and interlocking facilities including auto manual switch, NO/NC
contacts for automatic operation of fan in case of fire).
Incoming:
1 No. of 315 Amp TPN MCCB of 25 kA (Ics=Icu) Breaking capacity Micro-
processor based release with On Indicating Lamp with 2A SP MCB back-up.
Digital flush type class-1.0 accuracy multifunction meter showing V, A, PF,
KVAH, KWH etc. with 3 Nos. current transformers of 400/5A ratio, 15 VA
Class-1.0 metering.
1 Set of phase indicating lamp with 2Amps SP MCB back-up.
Bus Bar
400 Amp. 25 kA, TPN Al. Bus Bar
Page 86 of 119
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.No DescriptionTotal
Qty.Unit Rate Rate In Words MR-Amount
Outgoings:
250Amp TP,25 kA MCCB - 3 Nos.(2 for 100 HP pump+1 Spare)
32Amp TP,16 kA MCCB -2 Nos( 1No.for 10 HP jockey pump,1 spare)
Fully automatic Star Delta starter suitable for operating 75kw motors/fan
capacity, complete with contactors,Timer, overload protection relay, current
sensing type single phase preventer, ON indications, push buttons, auto /
manual / off selector switch,other accessories. complete as required. - 2 set.
Fully automatic Star Delta starter suitable for operating 7.5 kw motors/fan
capacity, complete with contactors,Timer, overload protection relay, current
sensing type single phase preventer, ON indications, push buttons, auto /
manual / off selector switch,other accessories. complete as required. - 1 set.
1 Set
34 CABLES
Supply, laying testing and commissioning of following sizes of XLPE
insulated PVC sheathed armoured aluminium conductor cable of 1.1 KV
grade on existing cable tray / surface including clamps, ties etc. as required.
34.1 3 Core 10 Sqmm. 60 Mtrs.
34.2 3 Core 120 Sqmm. 120 Mtrs.
35 Providing & fixing of control wiring/power cabling with following sizes of
copper conductor armoured cable between indoor and outdoor units directly
on surface of wall/ existing channel i/c making connection etc. as reqd.
35.1 3 x 1.5 sq.mm 200 Mtrs.
36 Fabricating and installation following size of perforated G.I. cable trays
including horizontal and vertical bends, reducers, tees, cross members and
other accessories as required and duly suspended from the ceiling with M.S.
suspenders and including painting with powder coating etc. as required:-
36.1 300 mm. Width x 50mm. Depth x 1.6mm. Thickness. 50 Mtrs.
36.2 450 mm. Width x 50mm. Depth x 2.0 mm. thickness. 70 Mtrs.
FIRE FIGHTING TOTAL
Page 87 of 119
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.No DescriptionTotal
Qty.Unit Rate Rate In Words MR-Amount
HVAC WORK
SUB HEAD 'A' - MACHINERY
1 Air Cooled Screw Chiller
Supply, installation, testing & commissioning of Aircooled Water Chilling
machine of 125 TR actual capacity minimum at operating conditions given
below with multiple nos. screw compressor (hermetic/ semi hermatic type)
operating on refrigerant R-134A, driven by suitable KW hermetic motor
complete having Star delta Starter with air-cooled condensers, insulated
shell and tube chiller, flow switch at chiller outlet, refrigerant piping,
refrigerant & oil (First Charge), microprocessor based control panel, spring
isolators of suitable capacity, incoming switchgear mounted in the starter
panel and accessories etc. all mounted on M.S. frame. The motors shall be
suitable for 415 volts ±10%, 50Hz± 5 %, three phase AC supply. The cost
of chilling machine shall include the transportation & insurance from works
to site.
Site Operating Parameters
Air Entering Temp. to the Condenser - 94 ºF
Chiller :- CHW in at 54ºF & CHW Out at 44ºF.
Chiller Foulning Factor - 0.0001 FPS
Chilled Water Flow Rate - 1135 LPM
Max. Chiller Pressure Drop - 10.0 Meter of WG.
Chiller Capacity - 125 TR (Actual)
The minimum COP and minimum IPLV at AHRI conditions should
compliance with ECBC code. AHRI certified performance sheet shall
be submitted with the offer .
Set 3
2 PUMPS
2.1 Supplying, erection, testing and commissioning of Centrifugal Vertical
Split Casing Primary Chilled Water pump set capable of delivering 1135
LPM of water against a head 15 Mtr. each pump shall comprise the
following as required as per specifications. (2 Working + 1 Stand by)
a) 1 No. - Vertical Split Casing type pump with bronze impeller, S.S Shaft, C.I
body and mechanical seal.
b) Lot - Duly insulated with 80 kg/cum density resin bonded fiber glass duly
cladded between aluminium sheets of 0.5mm thickness and properly
clamped to pump in two semicircular sections as per specifications.
c) 2 Nos. - 150 mm dia dial type pressure gauges. With stainless steel binders
& vibration dampers.
Page 88 of 119
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.No DescriptionTotal
Qty.Unit Rate Rate In Words MR-Amount
d) 1 No.- Suitable HP, TEFC squirrel cage induction motor with class 'F'
insulation, 1500 RPM synchronous speed, operating on 415 volts + 10%, 3
phase, 50 Hz A.C. supply.
e) Lot-Pump set shall be complete with necessary anti vibration pads,MS base
plate, coupling guard, foundation bolts and all other accessories. Set 3
2.2 Supplying, erection, testing and commissioning of package type
Centrifugal Vertical Split Casing Secondary chilled water pumping
system with VFD and all pump system controller, comprising of:
a) Pumping set with Cast Iron casing, Bronze impellers with stainless steel
shaft, connected to suitable capacity TEFC ventilated induction motor with
class' F' insulation of 3 Phase, 1450 RPM, suitable for 415 volts +10%, 3
phase, 50 Hz A.C. supply.
Lot - Duly insulated with 80 kg/cum density resin bonded fiber glass duly
cladded between aluminium sheets of 0.5mm thickness and properly
clamped to pump in two semicircular sections as per specifications.
b) Electrical Control Panel capable of cyclic operation of pumps - Pump
working sequence should change after every operation. Control panel
with programmable logic controller (PLC) with inbuilt PID controller, digital
display with fluorescent screen with two lines of min. 20 character each and
equipped with function keys and service keys. 3 ph, 415±10%V, AC
variable speed drive for each pump of suitable capacity rating having
standard function of BI loop, energy saving catching a spinning load with
speed search, auto hunting jog preset speeds, controlled stop on loss of
supply power loss side through, DDC injection breaking fast stop. Drive
should have rated input frequency 50 Hz and output frequency range of 0.5
to 132 Hz. Microprocessor based control panel shall have suitable hardware & software
so that it can be integrated directly with standard communication open
protocol using backnet / Modbus as well as open IP
(All the Pump set will have their control panel with respect to the motor
rating).
All pumps to be provided with separate variable frequency drives. Control
panel should also consist of cooling fan.
One panel for each job will be provided (for a set of two pumps) and the
panels should be installed adjacent to each other.
The pumps should be suitable for heating as well as chilled water
circulation.
c) Electronic Differential Pressure Transmitters as required.
Page 89 of 119
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.No DescriptionTotal
Qty.Unit Rate Rate In Words MR-Amount
Page 90 of 119
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.No DescriptionTotal
Qty.Unit Rate Rate In Words MR-Amount
d) suitable flanged suction and delivery headers in C-Class MS
e) Lot-Pump set shall be complete with necessary anti vibration pads,MS base
plate, coupling guard, foundation bolts and all other accessories. Complete
set system to be mounted on a common MS base frame
f) 2 Nos. - 150 mm dia dial type pressure gauges. With stainless steel binders
& vibration dampers.
Secondary chilled water pump sets
(1 Working + 1 Stand By)
Flow Rate : 2270 LPM
Head : 32 Metre WC Set 1
3 AIR HANDLING UNITS
3.1 Supplying, installing, testing and commissioning of factory built Floor
mounted double skin type horizontal air handling units made of 43 mm
thick panels consisting of pre plasticized G.I. casing of thickness 0.8 mm
outside layer and plane aluminum sheet of 0.8 mm inside layer with
polyurethene foam (PUF) insulation of density 32 kg/m3 factory injected
between them by injection moulding machine, complete with blower section
with blower DIDW backward curved centrifugal fan suitable for 115 mm WC
static pressure, 6 row deep cooling coil section with aluminium finned
copper tubes (tube thickness not less than 0.5mm), filter sections with 50
mm thick washable synthetic type Pre filters having efficiency 90% down to
10 micron and Fine filters having efficiency 99% down to 5 micron, belt drive
package with TEFC drive motor (Eff-1 ) suitable for VFD operation at 415 ±
10% volts, 50 Hz, 3 phase, A.C supply, complete with mixing box with
provision of fresh& return air (Fresh & Return air damper not in Scope),
drain connections with drain valve, 18 G stainless steel drain pan with PUF
insulation, thermometers and pressure gauge at the inlet and outlet of
cooling coil, necessary vibration isolation arrangement etc, complete as per
specifications of following capacities:
3.1.1 3200 CFM/ 17.0 TR Set 1
Page 91 of 119
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.No DescriptionTotal
Qty.Unit Rate Rate In Words MR-Amount
3.2 Supplying, installing, testing and commissioning of factory built Floor
mounted double skin type horizontal air handling units made of 43 mm
thick panels consisting of pre plasticized G.I. casing of thickness 0.8 mm
outside layer and plane aluminum sheet of 0.8 mm inside layer with
polyurethene foam (PUF) insulation of density 32 kg/m3 factory injected
between them by injection moulding machine, complete with blower section
with blower DIDW backward curved centrifugal fan suitable for 115 mm
static pressure, 4 row deep cooling coil section with aluminium finned
copper tubes (tube thickness not less than 0.5mm), filter sections with 50
mm thick washable synthetic type Pre filters having efficiency 90% down to
10 micron and Fine filters having efficiency 99% down to 5 micron, belt drive
package with TEFC drive motor (Eff-1 ) suitable for VFD operation at 415 ±
10% volts, 50 Hz, 3 phase, A.C supply, complete with mixing box with fresh
& return air provision (fresh & return air damper not in scope), drain
connections with drain valve, 18 G stainless steel drain pan with PUF
insulation, thermometers and pressure gauge at the inlet and outlet of
cooling coil, necessary vibration isolation arrangement etc, complete as per
specifications of following capacities:
3.2.1 1800 CFM/ 8.0 TR Set 3
3.2.2 2000 CFM/ 8.5 TR Set 1
3.2.3 2200 CFM/ 7.5 TR Set 3
3.2.4 2400 CFM/ 8.0 TR Set 1
3.2.5 4000 CFM/ 13.5 TR Set 4
Page 92 of 119
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.No DescriptionTotal
Qty.Unit Rate Rate In Words MR-Amount
3.3 AHU UNITS (WITH HEAT RECOVERY WHEEL)
Supply, Installation, Testing and commissioning of factory built floor
mounted double skin type horizontal air handling units made of 43mm thick
panels consisting of pre plasticized G.I. casing of 0.8mm outside layer and
plane GI sheet of 0.8 mm inside layer with polyurethane foam (PUF) thermal
break profile insulation of 38 kg/cum density injected between them,
complete with DIDW backward curve SA and RA blower section with blower
suitable for 50 mm static pressure for supply air fan & 30 mm for return air
fan, 4 row deep cooling coil section with aluminium finned copper tubes
(tubes thickness not less than 0.5mm), filter section with 50mm thick
washable synthetic type air prefilters belt drive package with TEFC drive
motor (EFF-1) suitable for VFD operation at 415 ± 10% volts, 50Hz, 3
Phase AC supply, heat recovery section with Heat Recovery Wheel as
described below, drain connections stainless steel (18G) drain pan with PUF
insulation, 150mm dia dial type pressure gauges and industrial type
thermometers at the inlet and outlet of coil, necessary vibration isolation
arrangement etc. complete as per specification and of following capacities.
Heat recovery wheel shall be designed for ambient temperature of DBT 88
°F & WBT 81.5 °F. The return air temperature of air stream will be DBT 77
°F & RH 55%. The Heat Recovery wheel should have equal efficiencies
both sensible & Latent greater than 75%. The desiccant of the wheel should
be Molecular Sieve 3 Angstrom to avoid any sort of cross contamination
between the two air streams. The Pressure drop across the HRW shall not
be more than 20mm. The Unit shall be supplied with weather proof cnopy i.e suitable for outdoor
installation.
3000 CFM/ 11.5 TR Sets 1
Fresh / Exhaust Air : 2150 CFM , Return Air : 850 CFM
2500 CFM/ 9.0 TR Sets 1
Fresh/ Exhaust Air : 1500 CFM , Return Air : 1000 CFM
1400 CFM/ 4.5 TR Sets 1
Fresh/ Exhaust Air : 640 CFM , Return Air : 760 CFM
3.3.1
3.3.2
3.3.3
Page 93 of 119
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.No DescriptionTotal
Qty.Unit Rate Rate In Words MR-Amount
3.4 Supplying, installing, testing and commissioning of Factory built Celing
suspended double skin type air handling units made of 25 mm thick panels
consisting of pre plasticized G.I. casing of thickness 0.6 mm outside layer
and plane GI sheet of 0.6mm inside layer with polyurethene foam (PUF)
insulation factory injected between them by injection moulding
machine,complete with blower section with blower DIDW forward curved
centrifugal fan of suitable static pressure as detailed below, 4 row deep
cooling coil section with aluminum finned copper tubes(tube thickness not
less than 0.5mm), filter sections with 50 mm thick washable synthetic type
air pre-filters having efficiency 90% down to 10 micron and Fine filters
having efficiency 99% down to 5 micron, belt drive package with TEFC
drive motor (Eff-1 ) suitable for 415+/-, 10% volts, 50 Hz, 3 phase, A.C.
supply, drain connections with drain valve, 18 G stainless steel drain pan
with PUF insulation , Descaling valve, auto air purge valve , necessary
vibration isolation arrangement along with suitable size of girder / pipes for
suport etc, complete as per specifications and of followings capacities.
3.4.1 1000 CFM / 3.0 TR - 50mm static Set 1
Page 94 of 119
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.No DescriptionTotal
Qty.Unit Rate Rate In Words MR-Amount
3.5 Supplying, installing, testing and commissioning of Factory built Celing
suspended double skin type air handling units made of 25 mm thick panels
consisting of pre plasticized G.I. casing of thickness 0.6 mm outside layer
and plane GI sheet of 0.6mm inside layer with polyurethene foam (PUF)
insulation factory injected between them by injection moulding
machine,complete with blower section with blower DIDW forward curved
centrifugal fan of suitable static pressure as detailed below, 4 row deep
cooling coil section with aluminum finned copper tubes(tube thickness not
less than 0.5mm), filter sections with 50 mm thick washable synthetic type
air pre-filters having efficiency 90% down to 10 micron, belt drive package
with TEFC drive motor (Eff-1 ) suitable for 415+/-, 10% volts, 50 Hz, 3
phase, A.C. supply, drain connections with drain valve, 18 G stainless steel
drain pan with PUF insulation , Descaling valve, auto air purge valve ,
necessary vibration isolation arrangement along with suitable size of girder /
pipes for suport etc, complete as per specifications and of followings
capacities.
3.5.1 4500 CFM / 12.5 TR - 30 mm static Set 1
3.6 Supplying, installing, testing and commissioning of factory built Ceiling
Suspended double skin type air handling units made of 25 mm thick panels
consisting of casing made of preplasticized GI sheet of thickness 0.6 mm
outside layer and GI plane 0.6mm inside layer with with polyurethene foam
(PUF) insulation of density 32 kg/m3 factory injected between them by
injection moulding machine, complete with blower section with blower DIDW
forward curved centrifugal fan of 25mm WC static pressure, 4 row deep
cooling coil section with aluminium finned copper tubes (tube thickness not
less than 0.5mm), filter sections with 50 mm thick washable synthetic type
Pre Filters having efficiency 90% down to 10 micron , direct drive package
with TEFC drive motor suitable for 220 ± 10% volts, 50 Hz, 1 phase, A.C
supply, complete with drain connections with drain valve, 18 G stainless
steel drain pan, necessary vibration isolation arrangement etc, complete as
per specifications of following capacities:
3.6.1 1000 CFM / 3.0 TR Set 1
3.6.2 1500 CFM / 5.0 TR Set 2
3.6.3 1600 CFM / 4.0 TR Set 4
3.6.4 1800 CFM / 5.5 TR Set 1
3.6.5 2200 CFM / 5.5 TR Set 1
Page 95 of 119
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.No DescriptionTotal
Qty.Unit Rate Rate In Words MR-Amount
4 FAN COIL UNITS
4.1 Supply, installation, testing and commissioning of Ceiling suspended Fan
coil units made of 0.8 mm thick pre plasticized G.I casing each complete
with 3 row deep cooling coil of copper tubes aluminium fins construction,
centrifugal fan, 3 speed motor, filter, insulated drain pan sandwiched type
having 0.8 mm thick stainless steel pan at the inner & 0.8 mm thick GI drain
pain as outer skin with an insulation of 13 mm thick closed cell nitrile rubber
between them , coil piping connections, condensate drain connection,
complete as required complete with bronze ball valve with and without
strainer, PID valves, thermostats and electrical wiring, manual air vent valve
etc. as required as per specification & drawings with the following
capacities:-
4.1.1 1.0 TR Set 5
4.1.2 1.5 TR Set 2
4.2 Supply, installation, testing and commissioning of Ceiling mount chilled
water cassette units made of powder coated galvanized steel housing
complete with fan section , chilled water coil section, 3 speed moter, drain
pump, bronze ball valve with and without strainer, PID valves , thermostat
and elctrical wiring etc. complete in all respect as per specification.
4.2.1 2.0 TR Set 2
4.2.2 1.5 TR Set 14
5 PHI CELL (PHOTO HYDRO IONIZATION CELL)
5.1 Supply,installation ,testing and commissioning of Photo hydro ionization cell
based on advanced oxidation technology with broad spectrum UV tube duly
enclosed in hydrated catalytic matrix cell with the capability to produce
friendly oxidizers like hydro peroxides, super oxide ions, ozonide ions &
hydroxide ions. The tube should be duly encased in poly tube to prevent
glass or mercury leakage into the atmosphere. The cell will have built in
fiber optic device as remote indication of this operation.
For R & D Space
5.1.1 1800-2400 CFM Nos. 8
5.1.2 4000 CFM Nos. 4
For Animal Holding Area
5.1.3 1400 CFM Nos. 1
5.1.4 2500 -3000 CFM Nos. 2
Page 96 of 119
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.No DescriptionTotal
Qty.Unit Rate Rate In Words MR-Amount
6.0 HEAT RECOVERY VENTILATOR
Supply, Installation, Testing and commissioning of Factory built Floor
mounted double skin horizontal type Heat recovery ventilation units
made of 43 mm thick panels consisting of pre plasticized G.I. casing of 0.8
mm outside layer and 0.8 mm Plane GI inside layer with polyurethane foam
(PUF) thermal break profile insulation of 38 kg/cum density injected
between them, complete with DIDW backward curve SA and EA blower
section with blower having suitable static pressure i.e 50 mm for supply air
Fan & 30 mm for exhaust air fan as given below, filter section at supply end
of 50mm thick washable synthetic type air prefilters belt drive package with
TEFC drive motor (EFF-1) suitable for 415 ± 10% volts, 50Hz, 3 Phase AC
supply, heat recovery section with Heat Recovery Wheel as described with
necessary vibration isolation arrangement etc. complete as per specification
and of following capacities. (The unit shall be provided with weather proof
cnopy.)
Heat recovery wheel shall be designed for ambient temperature of DBT 88
°F & WBT 81.5 °F. The exhaust air temperature of air stream will be 85.6 °F
DBT 55 % RH . The Heat Recovery wheel should have equal efficiencies
both sensible & Latent greater than 75%. The desiccant of the wheel should
be Molecular Sieve 3 Angstrom to avoid any sort of cross contamination
between the two air streams. The Pressure drop across the HRW shall not
be more than 20mm.
6.1 Supply Air : 6500 CFM , Exhaust Air : 4800 CFM Set 1
Page 97 of 119
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.No DescriptionTotal
Qty.Unit Rate Rate In Words MR-Amount
7.0 VARIABLE FREQUENCY DRIVES
Supply, Installation, testing & commissioning of HVAC dedicated VFDs
suitable for the following AHU fan motor capacity (The integration of the
VFD with AHU is included in this item) with IP 55 enclosures with Mains
disconnect, complying with the tender specifications and having:
Built-in dual 5% impedance DC link reactor (harmonic filters) on the positive
and negative rails of the DC bus of the VFD.
Built-in EMC Filters (electromagnetic compatibility filters) for VFDs for
restriction of conducted emissions to comply with IEC61800: 3 (unrestricted
distribution): 2004 Category C 1, for required length of cable between motor
& VFD.
Three-feedback PID (Propotional integrated derivative) controller having
capability to simultaneously accept 3 feedback signals from temperature
sensors for process optimization and accordingly regulate the speed of the
AHUs.
Automatic Energy Optimization for maximum energy savings.
The VFD shall be compatible with BMS.
7.1 4.0 KW Set 4
7.2 3.0 KW Set 1
7.3 2.2 KW Set 8
7.4 1.5 KW Set 1
7.5 1.1 KW Set 1
7.6 0.75 KW Set 2
7.7 0.55 KW Set 1
7.8 0.37 KW Set 1
Page 98 of 119
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.No DescriptionTotal
Qty.Unit Rate Rate In Words MR-Amount
SUB HEAD 'B' - VENTILATION
8.0 PRESSURIZATION FANS
8.1 Supplying, installation, testing and commissioning of Axial flow fan for
Pressurization of Lift Lobby, Lift Well & Stairwell of following capacity with
powder coated M.S. casing and aluminium alloy impellers with high
efficiency aero-foil sections, blades, the impeller directly driven by TEFC
induction motor (efficiency 1) suitable for 3 Phase 50 Hz 415 V ± 10 %,1400
RPM of class 'F' insulation etc. complete as required and as per
specifications . Fan shall be provided with suitable capacity of TPN isolator
with MS enclosure box.
8.1.1 15000 CFM /25 mm SP Nos. 2
8.1.2 13000 CFM /25 mm SP Nos. 1
8.1.3 5000 CFM /25 mm SP Nos. 2
8.1.4 3000 CFM /20 mm SP Nos. 1
8.1.5 2500 CFM /20 mm SP Nos. 2
9.0 CORRIDOOR SMOKE EXTRACTION VENTILATION FANS
9.1 Supplying, installation, testing and commissioning of Axial flow fan for
supply air of following capacity with powder coated M.S. casing and
aluminium alloy impellers with high efficiency aero-foil sections, blades, the
impeller directly driven by TEFC induction motor (efficiency 1) suitable for 3
Phase 50 Hz 415 V ± 10 %,1400 RPM of class 'F' insulation etc. complete
as required and as per specifications . Fan shall be provided with suitable
capacity of TPN isolator with MS enclosure box.
9.1.1 5000 CFM /15 mm SP Nos. 1
9.1.2 4000 CFM /15 mm SP Nos. 1
9.1.3 2000 CFM /15 mm SP Nos. 4
9.1.4 1000 CFM /15 mm SP Nos. 8
Page 99 of 119
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.No DescriptionTotal
Qty.Unit Rate Rate In Words MR-Amount
10.0 Supplying, installation, testing and commissioning of exhaust air Axial flow
fan of following capacity with powder coated M.S. casing and aluminium
alloy impellers with aero-foil sections, blades, the impeller directly driven by
TEFC induction motor (efficiency 2) suitable for 3 Phase 50 Hz 415 V ± 10
%,1400 RPM of class 'H' insulation etc. complete as required and as per
specifications .Fan and Motor shall be suitable for operation at minimum
250 deg C for 2 hrs. Fan shall be provided with suitable capacity of TPN
isolator with MS enclosure box.
10.1 4000 CFM /15 mm SP Nos. 1
10.2 2500 CFM /15 mm SP Nos. 2
10.3 2000 CFM /15 mm SP Nos. 8
11.0 Supplying, installting, testing and commissioning of Inline fan (Rectangular
Type ) for exhaust air with centrifugal blower and motor encased in sheet
metal casing, as per specifications. The motor shall be suitable for 220
voltage, 1 phase, 50 cycle AC cycle.11.1 1250 CFM /20 mm SP Nos. 4
11.2 850 CFM /20 mm SP Nos. 4
11.3 750 CFM /20 mm SP Nos. 4
11.4 550 CFM /20 mm SP Nos. 4
11.5 500 CFM /20 mm SP Nos. 4
11.6 450 CFM /15 mm SP Nos. 4
11.7 450 CFM /20 mm SP Nos. 4
11.8 350 CFM /20 mm SP Nos. 4
11.9 300 CFM /20 mm SP Nos. 4
11.10 300 CFM /15 mm SP Nos. 1
Page 100 of 119
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.No DescriptionTotal
Qty.Unit Rate Rate In Words MR-Amount
12.0 Supplying, installation, testing & commissioning of Propeller type exhaust
air fans suitable for following capacities complete with electric motor
suitable for operation on 220 V+ 10%,50 Hz, 1 phase AC supply fitted with
moumtings frames, louvers and bird screen etc. of the following capacities.
12.1 300 mm dia Nos. 6
13 Supply,installation ,testing and commissioning of ventilation Fan Sections
of Single Skin Construction, belt driven centrifugal forward curve DIDW
fan with vibration isolators and canvass connection , squirrel cage induction
motor, mounted within the housing and all other details as called for in the
drawings , specifications. Fan section shall be suitable for ceiling mounted
application, supplied with with 50 mm thick washable synthetic type air
filters having efficiency 90% down to 10 micron with extruded aluminum
frame (only for Fresh air ) as detailed in the drawings.The fan motor shall
be suitable for operation on Single speed , 220 ± 15 Volts, 50Hz, single
phase AC power.
13.1 5000 CFM /20 mm SP for Supply air Nos. 2
13.2 5000 CFM /15 mm SP for Exhaust Air Nos. 2
SUB HEAD 'C' CHILLED WATER PIPING WORKS
14 Supplying, fixing, testing and commissioning of following valves, strainers,
gauges in the chilled water plumbing duly insulated to the same
specifications as the connected piping and adequately supported as per
specifications.
14.1 BUTTERFLY VALVE WITH ON/OFF TYPE MOTORIZED ACTUATOR
Single phase 220V with limit switches, C I body & PN 16 pressure rating SS
Disc & shaft of Feedback, BMS Compatible for chilled water circulation as
specified duly insulatated of following sizes as per specification and
drawings. Cost should include necessary control wire (minimum size 1.5
sq.mm) 14.1.1 125mm dia. Nos. 3
Page 101 of 119
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.No DescriptionTotal
Qty.Unit Rate Rate In Words MR-Amount
15 BALL VALVE set with and without Y strainer with bronze body SS Disc,
Nitrile Rubber Seal & O- Ring PN 16 pressure rating for chilled water
circulation as specified.15.1 40mm dia. Set 9
15.2 32mm dia. Set 9
15.3 25mm dia. Set 5
16.0 PRESSURE INDEPENDENT CUM BALANCING CUM CONTROL VALVE
(PIBCV)
Pressure independent balancing and control valve (PIBCV) which shall be 2
way combined valve of PN 16 rating for flow limitation, controlling flow &
controlling Delta P. Valve body upto 32mm shall be brass and cast iron
above 32mm.Valve should be equipped with electronic modulating actuator
for AHU which can accept either "4(0)-20 mA / 2(0)-10 V DC signals.
Operating voltage for actuator shall be 24 V AC. The actuator should be
connected to propotionate thermostat. Delta p controller should ensure
100% control valve authority always at all load conditions (part load and full
load).Stepless balancing adjustments shall be in valve and control
adjustments in actuator. The differential pressure function shall be a
diaphragm and shall be out of the main flow to avoid valve blockages and
other services issue. Valve alongwith actuator shall offer logarithmic control
characterstics complete as per specification. The flow rates of chilled water
are as below :
16.1 19 - 34.0 LPM Nos. 5
16.2 34.1 - 64.2 LPM Nos. 9
16.3 64.6 - 102 LPM Nos. 9
16.4 102.4 - 189 LPM Nos. 7
17Supply, Installation, testing and commissioning of thermostat for various air
handling Units.Nos. 30
18 FLOW SWITCH SG Iron Body flow switch as per drawing & requirement. Nos. 3
Page 102 of 119
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.No DescriptionTotal
Qty.Unit Rate Rate In Words MR-Amount
19 Flexible connector for following Dia. Pipe, suitable pressure rating to be
installed at pump and chiller suction and discharge .
19.1 150 mm dia. Nos. 4
19.2 125 mm dia. Nos. 12
20 Supplying, fixing, testing and commissioning of G.I. medium class water
pipes of following size along with necessary clamps, fittings such as bends,
tees etc. adequately supported and duly insulated with closedcell XLPE
insulation material of 15mm thick as per specifications and as required.
20.1 80mm dia. RMT 50
20.2 65mm dia. RMT 80
20.3 50mm dia. RMT 100
20.4 40mm dia. RMT 50
20.5 32mm dia. RMT 50
20.6 25mm dia. RMT 30
21 CHILLED WATER EXPANSION TANK
Supplying, installation, testing and commissioning of M.S. expansion tank of
size 1.0mtr x 1.0 mtr x 1.0 mtr height made of 3mm thick mild steel sheet
complete with duly insulated with 50mm thick T.F quality expended
polystyrene of 24 kg/cum density covered with a layer of 120 gm/sqm
polythene sheet (vapour barrier) and finally cement plastered over chicken
wire netting of 24 gauge and complete with vent and drain connections with
float valve, quick fill and control valves etc. as required.
Set 1
22 Ball Valve of the following sizes as per specifications and drawings. (for
Drain)
22.1 40mm dia. Nos. 4
22.2 25mm dia. Nos. 11
Page 103 of 119
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.No DescriptionTotal
Qty.Unit Rate Rate In Words MR-Amount
23 Auto Air - purge valve of 15mm dia (Air Vent will be fitted with an isolating
ball valve)Nos. 6
SUB HEAD 'D' AIR DISTRIBUTION WORKS
24 Supply, installation, balancing and commissioning of Factory fabricated
Aluminium sheet metal (conforming to IS:737-1955 )rectangular ducting as
per BIS (IS : 655 ) standard, silicon sealed complete with neoprene rubber
gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per
approved drawings and specifications of following gauges:-
24.1 24 Gauge ( Thickness 0.63mm) Sqm. 150
24.2 22 Gauge (Thickness 0.8mm) Sqm. 1150
24.3 20 Gauge (Thickness 1.0mm) Sqm. 100
25 Supply, installation, balancing and commissioning of factory fabricated
corrosion proof Stainless steel sheet metal circular ducts , accordance with
the approved shop floor drawings and specifications.
25.1 20 Gauge (Thickness 1.0mm) Sqm. 100
26 Supply, installation, balancing and commissioning of Un-insulated flexible
duct of 100 mm dia, complete as required as per specifications. Mtr. 40
27 Supply, fixing and commissioning of powder coated extruded aluminum
exhaust air grilles complete with black anodized extruded aluminum VCD,
nuts, bolts, screws etc. as per approved drawings and specifications. Sqm. 2.5
28 Supply, fixing and commissioning of powder coated extruded aluminum
Supply/ return air grilles complete with nuts, bolts, screws etc. as per
approved drawings and specifications.
Sqm. 5.0
Page 104 of 119
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.No DescriptionTotal
Qty.Unit Rate Rate In Words MR-Amount
29 Supply, installation, testing and commissioning of black anodized extruded
aluminum Collar damper for supply air terminal , complete with neoprene
rubber gaskets, nuts, bolts, screws linkages, flanges etc, as per
specifications.
Sqm. 7.5
30 Supply, installation, testing and commissioning of Motorized GI volume
control damper with modulating actuator complete with neoprene rubber
gaskets, nuts, bolts, screws linkages, flanges & neesessary control wiring
etc, as per specifications.
30.1 Damper Sqm. 3.0
30.2 Actuator Nos. 12
31 Supply, installation, testing and commissioning of anodised aluminium fresh
air louvers with bird screen, filter and volume control damper with lever
mounting arrangement etc. as per specifications and drawings. Sqm. 6.0
32 Supply, installation, testing and commissioning of anodised aluminium
exhaust air louvers with bird screen, as per specifications and drawings. Sqm. 8.0
33 Supply,installation,testing and commissioning of factory fabricated, insulated
(with self adhesive XLPE / Nitrile rubber foam) square laminar air flow
plenum with diffusion plates , volume control device and openable
perforated sheet with 50% free area,suitable to be mounted in the standard
grid ceiling all duly fabricated in aluminum and powder coated, as per
specifications,
Sqm. 43.0
34 Supply, Installation, testing and commissioning of HEPA filter of 610 x
610mm x 155 thick having efficiency of 99.97% down to 0.3 micron partical
size complete with all respects and suitable to handle up to 550 CFM as
required.
Nos. 30
35 Air Differential Pressure Switch
Supply,installation,testing and commissioning of air differential pressure
switches complete with sensor probe , etc. integrated with Light and visual
alarm signal, as per general details and specifications to be installed across
HEPA filter bank sections & Labs rooms with necessary control and power
wiring.
Set 24
Page 105 of 119
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.No DescriptionTotal
Qty.Unit Rate Rate In Words MR-Amount
36 Temperature and RH sensor and adjuster package.
Supply,installation, testing and commissioning of micro-processor based
Room temperature , humidity sensor and remote adjuster package within a
MS housing on wall having a stainless steel cover plate.This package shall
have a temperature and humidity display - red 2" high LED character for lab
area .
Sensor, adjuster (Snap acting humidistat/Proportional thermostat-
Microprocessor based) and displayer package, as described above. Set 12
37 Duct mount type air flow sensor and adjuster package
Supply, installation, testing and commission of duct mount air flow sensor &
adjuster package for modulating the actuaors to maintain the desirable
positive / negative pressure relationship in the lab area with respect to the
adjascent areas.
Set 15
38 OIL DUCT HEATERS
Supply, installation , testing & commissioning of Flange Type Oil Duct
Heaters for labs & Animal holding area of following capacity, Oil Tank made
from S.S 316 L / 304 L Sheet with S.S Pipe 18mm Dia, with Heating
Elements (indirect Type) Porclin Heaters cartridge type with Electrical Panel
controls such as: Mater . Thermostat (Digital) and Step Thermostats. Panel
shall be wall mounted. The duct heater shall be suitable for following
capacity.38.1 1.5 KW Set 4
38.2 1.0 KW Set 11
Page 106 of 119
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.No DescriptionTotal
Qty.Unit Rate Rate In Words MR-Amount
SUB HEAD 'E' -INSULATION
39 Supplying, installation, testing of thermal insulation of supply air duct with
resin bonded glass wool insulation 50 mm thick with minimum density of 24
kg/m3.The entire insulation shall adhere with CR based adhesive 22-24%
solid grade having low VOC content and cladded/reinforced with canvas
cloth dipped and finished with thermal insulation protective coating ,
confirming to UL 723 or ASTM E-84. The coating method shall strictly
followed as per specifications.
SQM. 1600
40 Supplying, installation, testing of thermal insulation of return air duct with
resin bonded glass wool insulation 25 mm thick with minimum density of 24
kg/m3.The entire insulation shall adhere with CR based adhesive 22-24%
solid grade having low VOC content and cladded/reinforced with canvas
cloth dipped and finished with thermal insulation protective coating,
confirming to UL 723 or ASTM E-84. The coating method shall be as per
specifications.
SQM. 950
41 Supply and fixing of acoustic lining of supply air duct and plenum with
50mm thick resin bonded glass wool having density of 32 kg/m³, with 25mm
X 25 mm GI section of 1.25 mm thick, at 600 mm centre to centre covered
with Reinforced Plastic tissue paper and 0.5 mm thick perforated
aluminum sheet fixed to inside surface of ducts with cadmium plated nuts,
bolts, stick pins, CR based adhesive 22-24% solid grade having low VOC
content etc. complete as required and as per specifications.
SQM. 350
42 Supplying & fixing of acoustic lining on wall and ceiling of AHU rooms with
50mm thick, density 32 kg/m³ resin bonded glass fiber insulation friction
fixed in 610mm X 610 mm frame work made of 25X50X50X50X25 mm
made out of 0.6mm thick GI sheet U shaped channel and covered with
reinforced fiber glass tissue and finished with 0.80 mm perforated aluminium
sheet etc. complete as required and as per specifications.
SQM. 55
43 EXPOSED DUCT LINE THERMAL INSULATION
Supply and Application of 50mm thick insulation of Expanded
polysterene with a density of 20 Kg/Cum and finished with a vapour barrier
of 120 gsm polythene sheet & chicken mess sheet & a Layer of sand
cement plaster (ratio 1 : 4) 20 mm thick over it as per specification.
SQM. 300
Page 107 of 119
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.No DescriptionTotal
Qty.Unit Rate Rate In Words MR-Amount
SUB HEAD 'F' - ELECTRICAL WORKS
44 HVAC Panel (Plant Room)
Supplying, installation, testing and commissioning of dust, damp and vermin
proof free floor, indoor type standing factory built sheet steel enclosed
modular construction extendable panel, suitable for operation on 415±10%
volts, 50 Hz AC 3 phase 4 wire system fabricated out of suitable sized
square tubular section and covered with CRCA sheet steel of 1.6mm thick
for frame work and covers, 3mm thick for gland plates i/c cleaning &
finishing complete with 7 tank process for powder coating in approved
shade, complete with Aluminium bus bars, inter-connection with solid
copper conductor wires / aluminium strips, neutral links, earth bus etc.
necessary metering protections & indications and mounted with the following
as per drawing and technical specifications attached etc.
Complete as required. Control wiring with 1.5 sq.mm. PVC insulated FRLS
copper conductor Single Core cable. Each starter should have remote
control and interlocking facilities including auto manual switch, NO/NC
contacts for BMS control etc. complete as required.
The Panel should be IBMS compatible.
Incoming:
Air Circuit Breaker Horizontal drawout type of fault breaking capacity 50kA
(Ics=lcu =Icw) upto 433V Electrically Draw Out, fitted with interlocked door,
automatic safety shutters, mechanical ON/OFF and service/ test/ isolated
position indicators and frame earthing contact, conforming to IS-13947-2
1993 as amended up-to-date complete with following accessories for each
ACB.
Independent Electrical / manual spring closing mechanism - 1 Nos.
Microprocessor release (EMI & EMC certified) for over current, earth fault &
short circuit protection - 1 sets.
3 Nos. Phase indication LED lamps for each with 2Amp back up MCB,
breaker 'ON/OFF' indicating light with 2A MCB, test terminal block set,
circuits as per standard practice, auxiliary contacts for positive interlocking
of the breakers as required.
1 Nos. Intelligent multi-function digital panel meters of class 1.0 accuracy
with communication interface port R 485 for recording V (Between Phases
and between each phase and neutral, A (In each phase and neutral), KWHr
with suitable rating CTs, CT shorting links, R, Y, B LED indicating lamp and
2 A control SP MCB's.
i) Shunt trip coil 220V A.C.
1000 Amp FP EDO ACB - 2 sets.
Page 108 of 119
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.No DescriptionTotal
Qty.Unit Rate Rate In Words MR-Amount
Outgoings:
i) MCCB / ACB of following capacity 50KA(Ics=Icu upto 433 V) with
caliberated Intelligent multifunction digital panel meters of class 1.0
accuracy for recording V (Between Phases and between each phase and
neutral), A (In each Phase and neutral) with suitable rating CTs complete
with wiring connections etc.ii) 400 Amp. TP MCCB, 35 kA - 4 Nos.
iii) 100 Amp. TP MCCB, 35 kA -2 No.
iv) 63 Amp. TP MCCB, 35 kA - 3 No.
iv) 40 Amp. TP MCCB, 35 kA - 4 No.
Fully automatic DOL starter suitable for operating upto 4.5 kw motors/fan
capacity, complete with contactors, overload protection relay, current
sensing type single phase preventer, ON indications, push buttons, auto /
manual / off selector switch,other accessories. complete as required. - 3
Sets.
HVAC PANEL AS ABOVE Set 1
45 Pressurization Panels ( Loc. Plant room)
Supplying, assembling, erecting, connecting, testing and commissioning of
dust, damp and vermin proof free floor standing factory built sheet steel
enclosed non-drawout modular type Pressurization Panel fabricated out of
2.0 mm thick CRCA sheet hinged doors of 1.6mm thick CRCA sheet, duly
painted complete with earth bus, aluminium bus bar, numbering & sign
writing, interconnection & including the cost of connection through bus bar /
copper conductor flexible connection with necessary interlocking with
existing panel as shown in drawing as per specification and mounted with
the followings.
The Panel should be IBMS compatible.
Incoming:
100 Amp TP, 35 kA MCCB - 1 No.
3 Nos. Phase indication LED lamps with 2 Amps back up MCB, breaker '
ON/OFF' indicating light with 2A MCB
1 No. Intelligent multi-function digital panel meters of class 0.5 accuracy
with communication interface port R 485 for recording V (Between Phases
and between each phase and neutral, A (In each phase and neutral), KWHr
with suitable rating CTs, CT shorting links, R,Y, B LED indicating lamp and 2
A control SP MCB's.
Bus Bar
160 Amp. 35 kA, TP Al. Bus Bar
Outgoings:
40Amp TP, MCB - 4 Nos.
32Amp TP, MCB - 6 Nos. Set 1
Page 109 of 119
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.No DescriptionTotal
Qty.Unit Rate Rate In Words MR-Amount
46 AHU PANEL (8th & 9th Floor) (Loc-Plant room)
Supplying, assembling, erecting, connecting, testing and commissioning of
dust, damp and vermin proof free floor standing factory built sheet steel
enclosed non-drawout modular type AHU Panel fabricated out of 2.0 mm
thick CRCA sheet hinged doors of 1.6mm thick CRCA sheet, duly painted
complete with earth bus, aluminium bus bar, numbering & sign writing,
interconnection & including the cost of connection through bus bar / copper
conductor flexible connection with necessary interlocking with existing panel
as shown in drawing as per specification and mounted with the followings.
The Panel should be IBMS compatible.
Incoming:
100 Amp TP, 35 kA MCCB - 1No.
3 Nos. Phase indication LED lamps with 2 Amps back up MCB, breaker '
ON/OFF' indicating light with 2A MCB
1 No. Intelligent multi-function digital panel meters of class 0.5 accuracy
with communication interface port R 485 for recording V (Between Phases
and between each phase and neutral, A (In each phase and neutral), KWHr
with suitable rating CTs, CT shorting links, R,Y, B LED indicating lamp and 2
A control SP MCB's.
Bus Bar
160 Amp. 35 kA, FP Al. Bus Bar
Outgoings:
32Amp TP, MCB - 17 Nos.
32Amp DP, MCB - 8 Nos.
20Amp DP, MCB - 10 Nos.
Fully automatic DOL starter suitable for operating upto 3.0 kw motors/fan
capacity, complete with contactors, overload protection relay, current
sensing type single phase preventer, ON indications, push buttons, auto /
manual / off selector switch,other accessories. complete as required. - 6
Sets.
Set 1
Page 110 of 119
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.No DescriptionTotal
Qty.Unit Rate Rate In Words MR-Amount
47 AHU FLOOR PANEL (Loc- Service Floor)
Supplying, assembling, erecting, connecting, testing and commissioning of
dust, damp and vermin proof free floor standing factory built sheet steel
enclosed non-drawout modular type AHU Panel fabricated out of 2.0 mm
thick CRCA sheet hinged doors of 1.6mm thick CRCA sheet, duly painted
complete with earth bus, aluminium bus bar, numbering & sign writing,
interconnection & including the cost of connection through bus bar / copper
conductor flexible connection with necessary interlocking with existing panel
as shown in drawing as per specification and mounted with the followings.
The Panel should be IBMS compatible.
Incoming:
200 Amp FP, 35 kA MCCB - 1No.
3 Nos. Phase indication LED lamps with 2 Amps back up MCB, breaker '
ON/OFF' indicating light with 2A MCB
1 No. Intelligent multi-function digital panel meters of class 0.5 accuracy
with communication interface port R 485 for recording V (Between Phases
and between each phase and neutral, A (In each phase and neutral), KWHr
with suitable rating CTs, CT shorting links, R,Y, B LED indicating lamp and 2
A control SP MCB's.
Bus Bar
300 Amp. 35 kA, FP Al. Bus Bar
Outgoings:
32Amp TP, MCB - 18 Nos.
32Amp DP, MCB - 10 Nos.
20Amp DP, MCB - 20 Nos.
Fully automatic DOL starter suitable for operating upto 1.5 kw motors/fan
capacity, complete with contactors, overload protection relay, current
sensing type single phase preventer, ON indications, push buttons, auto /
manual / off selector switch,other accessories. complete as required. - 5
Sets.
Set 1
48 Corridor Smoke Panel (Loc- Service Floor)
Supplying, assembling, erecting, connecting, testing and commissioning of
dust, damp and vermin proof free floor standing factory built sheet steel
enclosed non-drawout modular type Corridor Smoke Panel fabricated out of
2.0 mm thick CRCA sheet hinged doors of 1.6mm thick CRCA sheet, duly
painted complete with earth bus, aluminium bus bar, numbering & sign
writing, interconnection & including the cost of connection through bus bar /
copper conductor flexible connection with necessary interlocking with
existing panel as shown in drawing as per specification and mounted with
the followings.
Page 111 of 119
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.No DescriptionTotal
Qty.Unit Rate Rate In Words MR-Amount
The Panel should be IBMS compatible.
Page 112 of 119
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.No DescriptionTotal
Qty.Unit Rate Rate In Words MR-Amount
Incoming:
100 Amp FP, 35 kA MCCB - 1No.
3 Nos. Phase indication LED lamps with 2 Amps back up MCB, breaker '
ON/OFF' indicating light with 2A MCB
1 No. Intelligent multi-function digital panel meters of class 0.5 accuracy
with communication interface port R 485 for recording V (Between Phases
and between each phase and neutral, A (In each phase and neutral), KWHr
with suitable rating CTs, CT shorting links, R,Y, B LED indicating lamp and 2
A control SP MCB's.
Bus Bar
160 Amp. 35 kA, FP Al. Bus Bar
Outgoings:
25Amp TP, MCB - 28 Nos. Set 1
49 DOL Panel
49.1 Fully automatic DOL starter suitable for operating upto 3 kw motors/fan
capacity, complete with contactors, overload protection relay, current
sensing type single phase preventer, ON indications, push buttons, auto /
manual / off selector switch,other accessories. complete as required.
Set 31
Page 113 of 119
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.No DescriptionTotal
Qty.Unit Rate Rate In Words MR-Amount
50 Supply, laying testing and commissioning of following sizes of XLPE
insulated PVC sheathed armoured aluminium conductor cable of 1.1 KV
grade on existing cable tray / surface including clamps, ties etc. as required.
50.1 3 Core 4 Sqmm. Mtrs. 250
50.2 3 Core 6 Sqmm. Mtrs. 300
50.3 3 Core 10 Sqmm. Mtrs. 100
50.4 3 Core 16 Sqmm. Mtrs. 50
50.5 4 Core 10 Sqmm. Mtrs. 30
50.6 4 Core 16 Sqmm. Mtrs. 30
50.7 3.5 Core 25 Sqmm. Mtrs. 20
50.8 3.5 Core 35 Sqmm. Mtrs. 50
50.9 3.5 Core 50 Sqmm. Mtrs. 20
50.10 3.5 Core 300 Sqmm. Mtrs. 75
51 Supplying and making end termination with brass compression glands and
Al. lugs for following size of PVC insulated and PVC sheathed / XLPE Al.
conductor cable of 1.1 KV grade as required.
51.1 3 Core 4 Sqmm. Set 50
51.2 3 Core 6 Sqmm. Set 30
52 Providing & fixing of control wiring/power cabling with following sizes of
copper conductor armoured cable between indoor and outdoor units directly
on surface of wall/ existing channel i/c making connection etc. as reqd.
52.1 2 x 1.5 sq.mm Mtrs. 1000
53 Fabricating and installation following size of perforated G.I. cable trays
including horizontal and vertical bends, reducers, tees, cross members and
other accessories as required and duly suspended from the ceiling with M.S.
suspenders and including painting with powder coating etc. as required:-
53.1 300 mm. Width x 50mm. Depth x 1.6mm. Thickness. Mtrs. 50
53.2 450 mm. Width x 50mm. Depth x 2.0 mm. thickness. Mtrs. 50
53.3 600 mm. Width x 75mm. Depth x 2.0 mm. thickness. Mtrs. 50
FIRE FIGHTING TOTAL
Page 114 of 119
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.No DescriptionTotal
Qty.Unit Rate Rate In Words MR-Amount
SUBHEAD-I: EFFLUENT TREATMENT PLANT
Design, Supplying, installing, testing & commissioning of Effluent
Treatment Plant (excluding excavation, back filling & disposal of
surplus earth Civil construction work) for the following duty:
Nature of effluent - The effluent waste generated from the
Laboratories shall be discharged into the ETP. Design to take
consideration of same.
Daily average flow:
ETP - 10 Cum / Day
INLET EFFLUENT CHARACTERSTICS
PROCESS EFFLUENT
pH - 6.5 - 9.2
Appearance: Colourless
Odour: Nil
TSS : 200 mg/litre
COD : 600 mg/litre
BOD :300 mg/litre
TDS : 1500 mg/litre
Oil & Grease : 50 mg/lIter
DISCHARGE EFFLUENT CHARACTERSTICS AFTER TREATMENT
pH - 6.5 – 7.5
BOD - Less than 30 Mg/L
S. Solids - Less than 100 Mg/L
COD - Less than 250 Mg/L
Oil & Grease - Less than 10 Mg / L
Turbidity - Less than 10 NTU
Appearance- Clear
Odour- Odourless.
Effluent treatment plant shall include the following items:
Screen Chamber
Oil & Grease Chamber
Effluent equalization tank/sump
Oil & Grease Removal Skimmer
Flocculation chamber
Tube settler tank
Filter feed water tank
ETP WORK
Page 115 of 119
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.No DescriptionTotal
Qty.Unit Rate Rate In Words MR-Amount
Sludge Holding Tank
Treated water tank
Air Blowers, Pumps & equipment
Piping, valves etc
Electrical Panel & Cabling
Note:
Contractor shall ensure submission of detailed GA drawings (Plan &
Section), P&I diagram, schematic diagram for the above said
component and additional component if so required for the complete
working of the ETP.
1 Supply, installation, testing & commissioning of 1 Nos Stainless Steel
Perforated, Corrugated Bar Screen with suitable lifting arrangement
(size 300 mm wide x 300 mm high approx).
1 Set
2 Supply, installation, testing & commissioning of belt type oil skimmer
complete with drive assembly and belt of required length.1 Set
Supply, installation, testing & commissioning of non clogging type
pumps with CI casing & C.I. impeller complete with all accessories,
motor of required capacity. Delivery header with isolation valve,
pressure gauge on delivery line with isolation cock, level controller (with
wiring) to control the level of sump automatically. Pumps shall have
following duty:
3 Pumps for transfer of Effluent (1 working & 1 standby) :-
Flow rate (each) = 1.0 m3/hr
Head = 8-10 Mtr 1 Set
Type of Pump- C.I. Non Clog type
4 Sludge disposal pump-Sludge Centrifuge Pump (2 Nos - 1 working + 1
Standby)
Flow rate (each) = 1.0 m3/hr
Head = 10-12 Mtr 1 Set
Type of Pump- C.I. Non Clog type
Page 116 of 119
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.No DescriptionTotal
Qty.Unit Rate Rate In Words MR-Amount
5 Twin type rotary air blowers capable of delivering required amount of
free air at required pressure driven through “V” belt or directly coupled
through flexible coupling to a TEFCmotor of suitable HP Suitable for 415
± 10% volts, 3 phase, 50 cycles A/C supply. The air blowers shall be of
following capacities :
Capacity : 25 cum/hr each (1 working + 1 standby)
Head : 0.4 Kg/ sq.cm 1 Set
6 Air grids for Equiliation Tank & Aeration systems shall comprise of pipes
droppers/ laterals , Header complete with all fittings such as tees,
crosses, plugs, sockets, elbows, reducers, supports & clamps, flanges
etc & making good. Contactor to submit detailed P & I indicating their
proposal.
1 Lot
Note :
Air dispersion system shall be provided for Effluent Collection & Dosing
Tanks.
7 Providing and fixing all piping (as described below) and isolation control
valves for making the system complete.
MS Epoxy : Air Blower Header Air piping , Interconnecting between
Pumps & Treatment module of etp1 Job
8 Supply, installation, testing and commissioning of Flocculation Tank
(MSFRP construction) consisting of flocculator & dosing systems for
Coagulant & Lime & polymer
1 Set
9Supply, installation, testing and commissioning of Aeration cum Settling
System in (MSFRP Construction) with suitable settling media. 1 Set
10 Supplying, installing, testing & commissioning of horizontal centrifugal
non clog water pumps with CI Head & Base, SS Impeller along with
motor, pressure gauge with isolation cock, Isolation valve, NRV on
delivery line. Isolation valve, stainer (with by-pass) at suction.
Mechanical seal, etc. The pump shall be suitable for 415±10% volts 3
phase AC supply. (1 Working + 1 Standby)
10.1 Capacity : 1.0 cum/hr
Head : 25 M
RPM : 2900 1 Set
Qty :- (1 working + 1 standby) - set
(Filter Feed Pump)
Page 117 of 119
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.No DescriptionTotal
Qty.Unit Rate Rate In Words MR-Amount
10.2 Treated Water Pumps
Capacity : 1.0 m3/hr
Head : 20-25 M
RPM : 2900 1 Set
Qty :- (1 working + 1 standby) - set
11 Providing, fixing, testing & commissioning of vertical MSRL filter with
manual operation with adequate dirt holding capacity (suitable for
3 Kg/Sqcm working pressure). The filter shall be as per
manufacturer's specifications complete with intitial charge filter media .
The filter shall also be provided with set of internals for raw water inlet
and bottom collecting system. Complete with frontal piping &
accessories.
1 Set
12 Providing, fixing, testing & commissioning of vertical MSRL activated
carbon filter with manual operation with adequate dirt holding
capacity (suitable for 3 Kg/Sqcm working pressure). The filter shall
be as per manufacturer's specifications complete with intitial charge filter
media . The filter shall also be provided with set of internals for raw
water inlet and bottom collecting system. Complete with frontal piping &
accessories.
1 Set
13 Top discharge type MS Basket centrifuge with SS basket suitable for 2
batches per day complete with all other accessories etc. The minimum
size of the basket should be 18"
1 Set
Page 118 of 119
PROPOSED CSIR INNOVATION
COMPLEX, MUMBAI
Sl.No DescriptionTotal
Qty.Unit Rate Rate In Words MR-Amount
14ELECTRICAL INSTALLATION FOR EFFLUENT TREATMENT PLANT
Design, fabrication, assembling, wiring, supply, installation, testing and
commissioning of motor control centre fabricated out of 14 gauge CRCA
sheet steel. Cable gland plates shall be provided on top as well as at the
bottom of the panels. Panels shall be treated with all anticorrosive
process before painting as per specifications with 2 coats of red oxide
primer and final approved shade of powder coated paint. 2 Nos.
earthing terminals shall be provided for 3 phase, 4 wire, 50 Hz supply
system. Lifting hooks shall also be provided in case of large panels.
Approval shall be taken for each panel before fabrication. Quoted rates
shall be inclusive of cables (in accordance to specification) with earthing
from panel to each motor / equipment.
1 Set
15 Additional : Civil and Electrical works LS
TOTAL
SUBHEAD-II: SEWAGE TREATMETN PLANT
1 Supply of packaged sewage treatment plant
complete with MS fabricated module, internal
and all equipments as mentioned in our scope
suitable for 40 m3/day. Excluding civil work
plumbing work and electrification 1 Set
2 Erection of packaged sewage treatment plant
complete with MS fabricated module, internal
and all equipments as mentioned in our scope
suitable for 40 m3/day. Excluding civil work,
plumbing work and electrification 1 Set
3 Additional : Civil and Electrical works LS
Total
Grand Total for ETP & STP
Page 119 of 119
Sl.No. Description Amount
1 CIVIL 243946180
2 PLUMBING 5023469
3 ELECRICAL INTERNAL 6009476
4 ELECRICAL EXTERNAL 76886
5 FIRE FIGHTING 19396
6 HVAC 3726992
A TOTAL 258802399
Sl.No. Description Amount
1 CIVIL
2 PLUMBING
3 ELECRICAL INTERNAL
4 ELECRICAL EXTERNAL
5 FIRE FIGHTING
6 HVAC
7 STP & ETP
B TOTAL
C GRAND TOTAL (A+B)
SUMMARY OF COST
CIVIL / INTERIOR WORK FOR PROPOSED CSIR INNOVATION COMPLEX, MUMBAI
(Schedule Rates)
TENDER DOCUMENT
SUMMARY OF COST
(Non Schedule Rates)