ProMinent gamma/ XL Solenoid Diaphragm Metering...
Transcript of ProMinent gamma/ XL Solenoid Diaphragm Metering...
4710/23/2019 - gamma/ XL
polymer blending &
dry feed solutionsProMinen t ® gamma/ XL So leno id D iaphragm Mete r ing PumpsOverv iew: gamma/ X
The new gamma/ XL is a solenoid metering pump with predictive intelligence. Thanks to its controlled solenoid drive with sensor-free pressure measurement, it detects hydraulic faults even in the case of minimal deviations – immediately and optimally matching its output to the pressure conditions and properties of the medium while protecting the pump and piping systems from overload situations. The gamma/ XL covers a capacity range of .006 GPD at 363 PSIG to 21.1 GPH at 29 PSIG (depending on pump version).
Electronic stroke length adjustment via click wheel Volume adjustment in GPH or LPH Manual, Analog, Contact and Batch modes optional Integrated system pressure measurement BUS interfaces such as Profibus, CANbus, PROFINET and Modbus High visibility of LED-indicator lights Large illuminated display Analog output for stroke length and stroke rate transmission Auto compensates programmed feed rates during back pressure fluctuations As low as 1 mL/hr continuous feed rate with regulated solenoid drive Turn down ratio up to 40,000:1 Integrated pressure measurement and display Available diaphragm rupture indicator Integrated 7-day timer Detects Overpressure/ No Pressure (broken discharge line) and gas in the liquid end Automatically sets optimal speed and stroke based on GPH settings (when set to automatic) New configurable input/output gamma/ XL and delta® footprints are identical
DU
LCO
TEST®
sensorsD
ULC
OM
ETER®
instrumentation
pump spare parts &accessories
motor-driven
metering pum
pssolenoid-drivenm
etering pumps
productoverview
48 10/23/2019 - gamma/ XL
poly
mer
ble
ndin
g &
dry
feed
sol
utio
nsProMinen t ® gamma/ XL So leno id D iaphragm Mete r ing PumpsCapac i ty Da ta
PSIG (bar) GPH* (L/H) ml/stroke Strokes/min in ft (m) NPE/NPB/PVT SS
2508 363 (25) 1.98 (7.5) 0.67 200 3/8" x 1/4" (1/2" MNPT dis. Only) 16.4 (5) 22.0 24.51608 232 (16) 2.06 (7.8) 0.67 200 3/8" x 1/4" 16.4 (5) 22.0 24.51612 232 (16) 3.17 (12) 1.00 200 3/8" x 1/4" 19.6 (6) 22.0 24.51020 145 (10) 5.18 (19.6) 1.70 200 1/2 x 3/8 16.4 (5) 22.0 24.50730 102 (7) 7.76 (29.4) 2.50 200 1/2 x 3/8 16.4 (5) 22.0 24.50450 58 (4) 12.95 (49) 4.20 200 5/8" ID hose barb standard*** 9.8 (3) 22.0 24.50280 29 (2) 20.74 (78.5) 6.70 200 5/8" ID hose barb standard*** 6.5 (2) 22.0 24.5
1608 232 (16) 1.85 (7) 0.60 200 1/2" x 3/8" 6.9 (2.1) 22.0 ~1612 232 (16) 2.64 (10) 0.80 200 1/2" x 3/8" 8.8 (2.7) 22.0 ~1020 145 (10) 3.96 (15) 1.25 200 1/2" x 3/8" 6.5 (2) 22.0 ~0730 102 (7) 7.26 (27.5) 2.30 200 1/2" x 3/8" 6.5 (2) 22.0 ~
*** (1/2” MNPT optional)
gamma/ XL metering pumps with high viscosity liquid ends (PVT 4) have a 10 – 20 % lower capacity rating and are not self-priming.
Permissible ambient temperature: 14 °F to 113 °F | Average power consumption: 78 W | Degree of protection: IP 66
Positive suction is recommended on pumps with 1/2” MNPT connections.
Repeatability ± 2% when utilized and installed per operating instructions
gamma/ XL with standard liquid ends
gamma/ X with auto-degassing liquid ends, without bypass PVT7
* Capacity data represents minimum values, tested using water at 68 ºF (room temperature)
** Suction lift with pre-primed suction line and liquid end
Capacity data: gamma/ XLPump Version
Capacity at Maximum Backpressure Max. Stroking Rate
Tubing Connectors O.D. x l.D SuctionLift ** Shipping Weight lbs
Version Liquid End Suction/discharge valve Ball seat Seals BallsNPT Acrylic PVC PVDF PTFE CeramicPVT PVDF PVDF PVDF PTFE CeramicNPE Acrylic PVC PVDF EPDM CeramicNPB Acrylic PVC PVDF FKM CeramicSST 316 SST 316 SST Ceramic PTFE CeramicSST (DN10) 316SST 316 SST PTFE with carbon PTFE CeramicNote: PVT7 versions have PVDF / PTFE wetted parts. Diaphragm with a PTFE face
FKM = fluorine rubber
Liquid end materials in contact with media
Mate r i a l s In Contac t Wi th C hem ica ls
Cont ro l E lements
12 14 151310 11
3
1
5 4
2
987
6
1 LCD screen2 [Menu] key3 Clickwheel 4 [Priming] key5 [STOP/START] key6 [Back] key7 Fault indicator (red)8 Warning indicator (yellow)9 Operating indicator (green)10 "Config I/O” terminal11 "Diaphragm rupture indicator" terminal12 "External control" terminal13 "Metering monitor" terminal14 "Level switch" terminal15 Slot for relays and optional modules
sole
noid
-driv
enm
eter
ing
pum
psm
otor
-driv
enm
eter
ing
pum
pspu
mp
spar
e pa
rts &
acce
ssor
ies
DU
LCO
MET
ER®
inst
rum
enta
tion
DU
LCO
TEST
®
sens
ors
prod
uct
over
view
4910/23/2019 - gamma/ XL
polymer blending &
dry feed solutions
Spec i f i ca t ions
P roMinen t ® gamma/ XL So leno id D iaphragm Mete r ing Pumps
Maximum stroke length: 110 mm solenoid approx. 2mm
Materials of construction:Housing Fiberglass reinforced PPE (Polyphenylene Ether)Diaphragm PTFE faced EPDM with plastic coreLiquid end options Acrylic/PVC, PVDF, Stainless SteelEnclosure rating IP 66Power supply 100 – 230 VAC 1 Phase 50 / 60 Hz ± 10%Power consumption 2508/ 1608/ 1612/ 1020/ 0730/ 0450/ 0280 78 WCheck valves Double ball suction / discharge (PVT4 with spring loaded single ball)Power cord 6ftRelay cable (optional) 6ftRelay Options:Identcode Option 1 Fault indicating relay, N/C 230 V - 6 A Max.Identcode Option 4 Fault indicating relay, N/C 24 V - 1 A Max. Pacing relay, normally open 24 V - 100 mA Max.Identcode Option C 4 – 20 mA current output Fault indicating relay 24 V - 100 mA Max.Ambient temperature range:In operation 14 °F to 113 °FStorage & Transport 14 °F to 122 °FMax. fluid operating temp Material Constant Short Term* Acrylic/PVC 104 °F 140 °F PVDF 122 °F 248 °F SS 122 °F 248 °F 15 minutes at 29 psi maximumClimate: 95% Relative humidity – non-condensingSound pressure level: LpA < 70 dB according to EN ISO 20361Warranty: 2 years on pump drive, 1 year on liquid endValve threads: NP / PVT M20 x 1.5 (provided with adapters for tubing)Standard production test: All pumps are tested for capacity at maximum pressure prior to shipmentContact input:Minimum pulse duration 10 msMaximum pulse input 50 pulses / secondAnalog Input Impedance 120 OhmsRecommended Viscosity Max. 0-50 cPs for standard liquid end Max. 50-200 cPs for valve with springs Max. 20-500 cPs for auto-degassing liquid ends Max. 500-1000 cPs for high-viscosity liquid ends
DU
LCO
TEST®
sensorsD
ULC
OM
ETER®
instrumentation
pump spare parts &accessories
motor-driven
metering pum
pssolenoid-drivenm
etering pumps
productoverview
50 10/23/2019 - gamma/ XL
poly
mer
ble
ndin
g &
dry
feed
sol
utio
ns
I den tcode Order ing Sys tem
ProMinen t ® gamma/ XL So leno id D iaphragm Mete r ing Pumps
GXLaRegional Version
US
Version Version2508 07301608 04501612 02801020
PVNPSS
BEFT
2347
67MNQ
01
0
0
U
ADVW
014C
01
03CDEMPR
Communication:0
ENGXLa US 1608 PV T 2 6 0 0 0 U A 0 0 0 0 EN
Diaphragm rupture indicator:
without connection
Hydraulic connections:
Liquid end version:
Without relayRelay, pre-set to:
100-240 V, ±10 %, 50/60 HzElectrical Connection:Standard, with logo
Without
Standard
CANopenManual + external with pulse control + analogue 0/4 - 20 mA
Control Variants:
Language:
Connection 1/2" x 3/8" USAConnection 3/8" x 1/4" USA
Standard Diaphragm/ EPDM seal
Version for highly viscous media
Standard connection for SST and PVT4 ONLY
Connection 1/4" x 3/16" USA
Standard Diaphragm/ PTFE seal
Bleed function, no valve springsBleed function, with valve springs
Auto degassing without bypass
Logo:Standard
Version:With diaphragm rupture indicator, optical sensorWithout diaphragm rupture indicator
Manual + external 1:1 with pulse control
CANopen DulcomarinPROFINET®
PROFIBUS® M12 plug
PROFINET® without certificateModbus RTU
With foot and injection valve
Cable and plug:European plug, 6 ft
N. American plug, 115 V, 32 ft
N. American plug, 115 V, 6 ftN. American plug, 115 V, 16 ft
Without accessoriesAccessories:1 x N/O 24 V – 100 mA, such as 1 + 4 – 20 mA output2 x N/O 24 V – 100 mA, such as 1 + pacing relay1 x changeover contact 230 V – 2 A, fault indicating relay N/C
Liquid end material:
Product Range
North America
Capacity1.98 gph (7.5 l/h), 362.6 psi (25 bar)2.06 gph (7.8 l/h), 232 psi (16 bar)3.17 gph (12 l/h), 232 psi (16 bar)5.18 gph (19.6 l/h), 145 psi (10 bar)
Capacity7.76 gph (29.4 l/h), 102 psi (7 bar)12.95 gph (49 l/h), 58 psi (4 bar)20.74 gph (78.5 l/h), 29 psi (2 bar)
PVDF/PVDF, not for pump type 2508Clear acrylic /PVC, only for pump types 2508, 1608, 1612, 1020 and 0730Stainless Steel
Standard Diaphragm/ Viton-B seal
FDA-Compliant
O-rings:
sole
noid
-driv
enm
eter
ing
pum
psm
otor
-driv
enm
eter
ing
pum
pspu
mp
spar
e pa
rts &
acce
ssor
ies
DU
LCO
MET
ER®
inst
rum
enta
tion
DU
LCO
TEST
®
sens
ors
prod
uct
over
view
5110/23/2019 - gamma/ XL
polymer blending &
dry feed solutionsProMinen t ® gamma/ XL So leno id D iaphragm Mete r ing PumpsDimens iona l D raw in gs
ØA
B
0.98
C
2.24
5.438.15
9.17
4.72
5.51
0.25
D
E
1.04
5.90
1608 1612 1020 0703⌀A 3.54 3.54 3.54 3.54B 4.25 4.33 4.33 4.40C (with bleed valve) ~ 5.12 5.12 5.20C (SER) 5.03 5.12 5.12 5.20D 2.50 2.50 2.50 2.50E 9.45 9.45 9.45 9.45Note: The above drawing represents the PV liquid end version (see O&M for all other) All measurements are in inches
DU
LCO
TEST®
sensorsD
ULC
OM
ETER®
instrumentation
pump spare parts &accessories
motor-driven
metering pum
pssolenoid-drivenm
etering pumps
productoverview