Production of High Quality Dry Ice Pellets - mycoldjet.com sheet-EN-rev7.pdf · | Dry Ice...
Transcript of Production of High Quality Dry Ice Pellets - mycoldjet.com sheet-EN-rev7.pdf · | Dry Ice...
ww
w.icetech
world
.com | D
ry Ice Techn
ology | R
ev7 2017.08.22 | EN
Technical Data
Dimensions mm/in:Length: 1500 / 59Width: 1500 / 59Height: 1800 / 71Height: 1870 / 74 (incl. ext. legs) Weight: kg: 1925 / lbs: 4244 Rated Output:kg/h: up to 750lbs/h: up to 1653of high-quality dry ice pellets, depending on the extruder plate applied Pellet Size Diameter:mm: 3 - 10 or 16in: 0.11 - 0.39 or 0.62
Inlet Liquid CO2 Pressure:bar: 16 - 22psi: 232 - 319
Back Pressure on Revert Gas:bar: 0 - 1psi: 0 - 14.5 CE Power Supply:3 x 400 V AC + PE, 50Hz, Imax. 32 A
UL Power Supply:3 x 480 V AC + PE, 60Hz, Imax. 32 A
Rated Power: kW: 11 Hp: 15
Noise Level Below 75 dB(A)
PR750HProduction of High Quality Dry Ice Pellets
3 mm Pellets 10 mm Pellets 16 mm Pellets
The IceMaker PR750H can produce two sizes of pellets at the same time.
3 mm Pellets 16 mm Pellets
powered by
Americas + 1800 337 9423 EMEA +32 (0) 13 53 95 47 Germany +49 (0) 6551 9606-0 Asia-Pacific +81 3 6869 2665www.coldjet.com www.icetechworld.com
ww
w.icetech
world
.com | D
ry Ice Techn
ology | R
ev7 2017.08.22 | EN
PR750HProduction of High Quality Dry Ice Pellets
Height: mm: 1870in: 74 (incl. ext. legs)
mm: 1500 in: 59
1030 mm max. 40.5 in max.
Height: mm: 1870in: 74 (incl. ext. legs)
1100 mm max.43 in max.
1500 mm / 59 in
1500 mm / 59 in
If the IceMaker PR750H is connected to your LAN or Internet, the entire display can be transferred to the computer desktop of your choice– anywhere in the world.
This allows online support by using diagnostic software on the industrial PC.
Height: mm: 1150in: 45 (incl. ext. legs)
Height: mm: 1150in: 45 (incl. ext. legs)
795 mm / 31 in
511 mm / 20 in
Floor Characteristics and Minimum Clearance Distanceso The pelletizer must be placed on a horizontal concrete floor with an adequate load-carrying capacity. The pelletizer will be anchored to the floor, which must be free of cracks and structural deficiencies.o The minimum clearance distances must be observed to provide sufficient space for opening the cabinet doors and servicing the pelletizer.
InstallationThe installation of the pelletizer must be carried out by one of Cold Jet’s service technicians, or bya technician approved by Cold Jet.
Americas + 1800 337 9423 EMEA +32 (0) 13 53 95 47 Germany +49 (0) 6551 9606-0 Asia-Pacific +81 3 6869 2665www.coldjet.com www.icetechworld.com
powered by