Product Overview.doc
Transcript of Product Overview.doc
User Manual
Mobile Digital Video Recorder
NOTICE
The information in this manual was current when published. The manufacturer reserves the right to revise and improve its products. All specifications are therefore subject to change without any notice.
The purpose of this manual is to kindly aid the user in the installation of the CMS software. The user should have a basic understanding of computer operation and basic knowledge of how to connect peripherals and make some settings.
This manual is not intended to train the operation for CMS, Please refer to the Users Manual for CMS operation (B1-CMS-GUI-0-08-A) for the CMS operation information
Copyright
Under copyright laws, the content of this manual may not be copied, photocopied, reproduced, translated or reduced to any electronic medium or machine- readable form, in whole or in part, without prior written consent of SecuMaster Technology Co., Ltd Copyright 2005-2008, SecuMaster Technology, Co., Ltd
Environmental Conditions
Have a MDVR from SecuMaster working fine with CMS softwareHave a PC with Windows XP (We strongly recommend XP) and make sure that the PC can go online by WAN.SQL Server. Please install SQL server before install CMS programCMS installation programCorrect MDVR setting to make sure CMS can work fine.
Page 2, total 45
Table of Contents
1. Product Overview....................................................................................................................41.1 Product Views..............................................................................................................41.2 Product Features..........................................................................................................4 1)Recording…………………………………………………………………………………………4 2) Metadata…………………………………………………………………………………………..4 3) Wireless network function……………………………………………………………………….41.3 Specification.................................................................................................................4
2. Installation Guideline............................................................................................................62.1 Front Panel...................................................................................................................62.2 Rear Panel...................................................................................................................72.3 Remote controller…………………………………………………………………………….8
3. System Start-up and login..............................................................................................113.1 System Start-up.........................................................................................................113.2 System Login.............................................................................................................11
4. MDVR System Layout.........................................................................................................124.1 System Management.................................................................................................12
4.1.1 File operation……………………………………………………………………………...124.1.2 Shortcut……………………………………………………………………………………144.1.3 Format……………………………………………………………………………………..15
4.2 Setup..........................................................................................................................164.2.1 GENERAL…………………………………………………………………………………16 1) Date/Time………………………………………………………………………………….16 2) General…………………………………………………………………………………….18 3) System ID………………………………………………………………………………….19 4) Security…………………………………………………………………………………….21 5) Default……………………………………………………………………………………...22 6) Update……………………………………………………………………………………..234.2.2 Record setup………………………………………………………………………………23 1) Record setup………………………………………………………………………………23 2) Channel setup……………………………………………………………………………..25 3) Alarm setup………………………………………………………………………………..264.2.3 Network setup……………………………………………………………………………..304.2.4 ALARM…………………………………………………………………………………….31 1) Sensor……………………………………………………………………………………..31 2) Speed………………………………………………………………………………………33
4.3 Playback.....................................................................................................................344.4 Event Search..............................................................................................................364.5 System Information....................................................................................................38
5. MDVR Basic Working Parameter..................................................................................396. MDVR Appreance and Interface...................................................................................407. Unit Wiring......................................................................................................................42
Page 3, total 45
1. Product Overview
1.1 Product Views
The mobile DVR is a device which special designed for vehicle surveillance with CIF/HD1
resolution. It adopt to the high speed processor and embedded operation system, intergreated
with the latest H.264 video compression/ decompression technology in IT field, network
technology and GPS navigation technology. It can do Center monitoring with alarm、 remote
monitoring and playback analysis based on center database. The appearance is very
concision、anti high temperature, vibration absorber, flexible installation, strong function, and the
system runs very stable.
1.2 Product features
1) Recording
Support 1 channel live view H.264 record and 1 channel audio record;
Movable HDD storage to read data,
The recording definition is CIF/HD1,
Automatic adjust the recording data according to the sensor info to save HDD space.
The playback function supports sensor searching playback,
2) Metadata
Support 6 sensors input interface, 2 RS485 interface, 3 RS232 interface,
Collect most sensors data of the vehicle, including temperature, speed, brake, back a car
etc, and can adjust recording data size.
User can search the recording files easily according to metadata.
3) Wireless network function
Supports broadband or narrowband application, and can upload the live view,
Upload single channel and more channels video’s corresponding frame according to
bandwidth limitation,
Support CDMA/EDGE/GPRS wirless network application.
1.3 Specification
Item Description Parameter
SystemOS language Chinese/English
Operation interface OSD GUI
Page 4, total 45
Password control User password, admin password
Video
Video Iput 1 channel composite input 1.0Vp-p,75Ω BNC
Video Otput1 channel. Composite video output 1.0Vp-p,75Ω BNC
Video display Single video display
Video standardPAL system 25F/S CCIR625 Lines 50 Hz
NTSC system 30F/S CCIR525 Lines 60 Hz
Audio
Audio input Single audio input 600Ω BNC
Audio output Single audio output 600Ω BNC
BaBasic output power level 1V – 2V
Recording type Audio and video synchronized
Audio compress ADPCM
Video process and storage
Video compress H.264 VBR/ CBR
Video format CIF/HD1
Video streaming standard
ISO14496-10
Audio streaming standard
ADPCM
Video streaming(kbps)
CIF: 256Kbps ~ 1.5Mbps 8 grade video quality optional 1grade is the best.
HD1: 600Kbps ~ 2.5Mbps 8 grade video quality optional 1 grade is the best
Audio streaming 4Kbytes/s
Storage SATA HDD up to 500GB
Alarm
Motion detectionEach channel up to 192 detection zone, sensitivity adjustable
Alarm input Can config 4~6 power level input
Alarm output Can config 2~4 power level output
Corresponding interface
Serial interface Supports 3 RS232 interface
Serial interface Supports 2 RS485 interface
Network interface RJ45 10M/100M auto adapt network interface
Wireless
correspond
CDMA Built-in CDMA module optional
EDGE Built-in EDGE module optional
GPRS Built-in GPRS module optional
GPSBuilt-in GPS navigation module, GPS info were encoded streaming, it can
be wireless upload.
Matchable PC playback analysis Playback video files and analysis the vehicle
Page 5, total 45
software
info
CMS
Live view video by wireless network,
GPS information upload,
alarm upload and center command sending,
parameter configuration etc.
Upgrade USB upgrade, HDD upgrade
The others
Power input +8V ~ +36V
Power output +12V@2A;+5V@2A
Working temperature -25----60℃
Working humidity
Weight
2 Installation Guideline
2.1 Front panel
1. LED indicator lights and status index:
【POWER】Power input status: LED ON confirms that unit is power supplied.
【U DISK】U driver indicator LED: LED ON—U driver in device,
LED OFF —means no U driver.
【REC】Video recording status LED: LED ON indicates recording is on.
【VIDEO】Video loss LED: LED ON indicates video input well.
LED OFF indicates video loss.
【ERR】Disk faults LED: LED is on-HDD is working wrong; LED is off-HDD is working
well.
Page 6, total 45
【SD】For future use, No action now.
2. IR : Remote control IR receiver.
3. DEBUG: Serial port debugging.
4. MCU: MCU upgrading interface
5. USB: U driver and data transfer interface.
6. AUDIO OUT: Audio output
7. VEDIO OUT: Vedio output.
2.2 Rear Panel
1. RJ45: Network card interface
2. RS232: Expand serial
3. RS485 I/O: Expand serial
4. A/V : Audio/video input and output interface
5. POWER: External 12V power supply(Red cable connect with + , the black cable
connect with —, the yellow cable connect with signal cable, three cables must be
connected)
6. GPS: GPS antenna port
7. CDMA: CDMA antenna port
Page 7, total 45
2.3 Remote Controller
Each MDVR includes a handheld Infra-Red(IR) controller that allows the user to transmit
commands to recording module and display on screen control menu on a composite monitor.
Page 8, total 45
Number keys: Use the numbers to input values in the system setup.
Navigation Arrows: Use the ARROW to move between selections, input fields and icons. Press Enter to select and EXIT to return.
Remote control key and function introduction:
1. Number keys:
【0-9】keys:During setup, number keys are used to input values.
For viewing channels 1,2,3 and 4, use 1,2,3 and 4 on numeric keypad respectively.
【+】、【-】keys:During setup, plus and minus are used to select next or previous values.
2. Setup menu navigation:
▲, : Up, Down directional keys: Move selection up and down in setup menu.
, : Left, Right directional keys: Move cusor left or right in setup menu.
【Enter】key: During setup, select and save entry
During Playback and preview, displays the channel name, text number, driver
name, event sensor item and time, year/month/date, time, GPRS/GPS info.
on the screen.
3. PTZ(Lens)function control keys
【ZOOM+】、【ZOOM-】:Zoom in/out
【APERTURE+】、【APERTURE-】:IRIS control
【FOCUS +】、【FOCUS-】:Focus in/out
【AUTO】:Auto run with the PTZ pattern
【RECALL】:Recall the set program
【PRESET】:Preset default position
【SWITCH】:To control the brush、lamplight and so on assistant relays.
4. Play function keys
【PLAY】:Starts/Resumes playback from any other mode (FF, RR, Frame by Frame etc)
【SLOW】:Reduces playback speed to 1/2X、1/4X、1/8X、1/16X mode. Press PLAY to
return to normal playback speed.
【PAUSE/STEP】:Freezes playback to single frame and can advance one frame at a time.
To advance the frame press Pause/Step to move frame by frame. Press
EXIT to return to normal playback speed.
【FWD】: Fast forward the video while playback.X1, X2, X3, X4 modes available. PressFWD
Page 9, total 45
to switch, press 【PLAY】to return to normal speed;
【REV】: Reverse the video while playback, 1X,2X,3X,4X four modes are available. Press
REW to switch, press【PLAY】 to return to normal speed;
5. The other function keys:
【POWER ON】: Reset the MDVR to Power on and Power off mode. (standby and start up);
【LOGIN/LOCK】: If the security is enabled in the setup, use LOGIN/LOCK key to enter the
user setup. It is important to remember the password due to without
restoration function. Log in( to enter into “User ID select” and “Password”
input interface)and lock functions(To exit setup and operation);
【QUAD】: Switch between preview and playback;
【PARAMETER】:No function;
【ANALOG】:To adjust the brightness、contrast、chroma、the sensitive of motion detection
when at single channel live view,cooperate with 【+】、【-】 to adjust the
parameters;
【EXIT】: Exit to the preview or return to the last menu;
【CF】:To operate CF card when the system with CF card;
【LANGUAGE】:When set the channel name uder the record setting interfac,press this key switch input language of Chinese or English;
【RECORD】:Start manual record;
【STOP】: Stop manual record;
【SETUP】:Enter into setup interface and setup the system parameters;
【F1】:Choose time play of record video;
【F2】:PTZ control,press this key to enter into PTZ control interface when at single live
view;
【F3】, 【F4】, 【CHECK】, 【NET】:no use at preset.
Page 10, total 45
3. System Start-up and login
3.1 System Start-up
MDVR is in standby status after connecting the MDVR power cable to vehicle DC 12V power
supply, MDVR start up is subject to the setup of user. (Please see the details in the GERNERAL
and RECORD of Setup). Normally the vehicle can supply power to MDVR when Ignition is ON or
vehicle with laden, the following is the sign of MDVR is power on.
When Video out display customer’s LOGO or Setup interface. If vehicle’s power is not off,
MDVR record signal is continue, if vehicle power is off, MDVR still can keep working.
3.2 System Login
1) When Password is set disable, press 【Login/Lock】key, then will appear the following
interface, input Unit ID and User Name to enter system main menu.
2) When Password is set enable, Press 【Login/Lock】key, then will appear the following
interface, input Unit ID, User name and Password to enter system main menu.
Page 11, total 45
Unit ID:The default is 20008
User Name:User can check the record file、sensor menu data only;Admin has the all
authorities to operate the all functions;(The default is Admin, press【Enter】 to switch
from general user and admin)
Password:Default admin password is 000000,Default user password is 888888
4. MDVR System Layout
Press 【Login】on the IR controller, then login to the system the on-screen menu will be
displayed:
Navigate through the option using the ARROW keys.
Select the desired option using 【Enter】key(The system will continue record when
users enter into selected item, only when users select playback or modify relevant
record parameters, then the system will stop record);
To turn to the previous menu from any screen use 【Exit】key
Page 12, total 45
4.1 System Management
To use the direction key to select and press【Enter】key,to enter into the management menu which including the system parameter setup.
4.1.1 File Operation
The main function is to copy and delete the recording files.
The search File search menu display the current month record information, the date with white color
means this day with recording file.
To search the recording files by the number keys and direction keys on the remote control:
Type:Press【Enter】 to select the searching way:All/Alarm/Motion detection/Power
on/Manual/Timer。
Page 13, total 45
“(Year)”: The range is 2000~2099,to press number keys to enter.
“(Month)”: The range is 01~12,to input the relevant month to search.
“(Date)”: The range is 01~31,to input the relevant date to search.
“(Hour)”: The range is 00~23,to input the relevant hour to search.
“(Minute)”: The range is 00-59,to input the exact time to search.
After inputting the exact start time, move the cursor to “search” button and press 【Enter】to
enter into the recording file lists interface:
Page 14, total 45
To select the recording file by direction keys or 【+】、【-】, and press【Enter】means
selected OK( There is a blue dot at the front of the selected recording files ) and press
【Enter】again the blue dot will disappear that means cancel the select, we can export and
delete the recording files after selecting, and press【Exit】to return to the last menu.
4.1.2 Shortcut
To be used to copy different types of files.
To move the cursor to the relevant option and press 【Enter】, the selected option will show a
blue dot at the front, then “Apply”, the selected files will be copy to the USB storage.
Page 15, total 45
4.1.3 Format:
External device:To select an external device by press【Enter】to switch , after selecting
“External device”, press 【Enter】 to confirm, then will pop up a dialog for selecting “Apply” or
“Cancel” to Format.
Page 16, total 45
4.2 Setup
To press direction keys to select and press 【Enter】, when you enter into setup menu
and revise the relevant recording parameters, the system will stop all record, and the setup menu
including the system parameter setup.
4.2.1 GENERAL
Press【Enter】to change system setup inforamtion.
To move the cursor to the GENERAL setup and the left column is the GENERAL setup
sub-menu.
To move down direction key to sub-menu.
To move the cursor by pressing the up and down direction keys and select the relevant
sub-menu, cursor rightward to enter into the sub-menu and select the options to do
settings.
Move cursor to APPLY and press【Enter】key will save the settings, press 【Exit】will
back to submenu of GENERAL.
If not press【Enter】key and exit, then the modified setting will not been saved.
The GENERAL menu consists of six tabs. Each tab is designed to facilitate the performance
adjustments preferred by the user.
1) Date/Time:
Page 17, total 45
a) Date format:MM/DD/YYYY Press【Enter】to input.
b) Current date:MM/DD/YYYY To input by number keys
c) Current time:H/M/S To input by numberic keys.
d) Sync mode:Manual/Auto Press【Enter】to switch.
e) Sync type:NTP/GPS Press【Enter】to switch.
Page 18, total 45
f) NTP sync IP:Network service IP address.
g) Sync time:H/M/S Number keys input
h) Current time zone:GMT+Number Press【Enter】to input.
The behind four options get grey when sync mode is manual.
2) General:
a) Time Mode: ignition/(Time&ignition)/(Time︱ Ignition)/Timer, press 【Enter】 key to
switch each mode
When MDVR in standby status, user setting Time Mode as following:
Page 19, total 45
Ignition: MDVR will be startup/shutdown according to ignition signal.
Timer: MDVR will be startup/shut down at a specific time.
Time&Ignition: MDVR will be startup when ignition on time is same as Startup
Time setting, and MDVR will shutdown when ignition off time is same as
Shutdown Time setting.
Time︱Ignition MDVR will start up at Startup Time setting or ignition is on, and
MDVR will shutdown at Shutdown Time setting or ignition is off.
b) Startup Time: H/M/S Enter with number keys
c) Shutdown Time: H/M/S Enter with number keys
While use Timer to start up/shutdown MDVR, the time setting rules as following:
When Startup Time is less than Shutdown Time, device start up time is between
Startup Time and Shutdown Time.
When Shutdown Time less than Startup Time, device shutdown time is between
Shutdown Time and Startup Time. (MDVR startup time is at first day, then
shutdown time will be at second day.)
d) Shutdown Delay: range is 5~300 minutes, enter with number keys. Allow the system
continous running when vehicle turn off (ignition signal OFF), after Delay off time, it will
shutdown automatically.
e) Idle Time: Range is 30~1800 seconds, enter with number keys. when user enter GUI
interface, it will be back to preview screen when no operation during this time.
f) System Maintenance: On/Off press 【Enter】 to switch
3) System ID
Page 20, total 45
a) Unit ID: Use the Numberic keypad to enter the unit ID between 00000-99999,
this ID is used when logging in to the unit (if security is enabled).
b) The Company Name, Vehicle No. and Driver Name, press 【Enter】 , enter into
keypad interface to input corresponding names.
Page 21, total 45
1. Input: Use ARROW key to select the option to input.
2. Type: Chinese, English, Number, press 【Language】 key to switch
Page 22, total 45
4) Security: Press 【Enter】 to select On or Off, import password with number keys.
Password
ON: need to input password to login.
Off: Input Unit ID and user name only to access Menu interface, no need to input
password.
User Password Correct indicates permission is limited to video, sensor menu.
Admin Password correct indicates full access to all Menu of MDVR.
No password or simply password will effect not convenient to manage MDVR.
Page 23, total 45
5) Default operation
Default Setting: Press 【Enter】 to switch between”cancel” and “Apply”, Selecting”Apply”
will restore the default factory settings.
Export setting: Press 【Enter】 key will export device configuration file” config.dvr” to U
disk root of directory.
Import setting: Press 【Enter】 will import configuration file” config.dvr” from U disk or
HDD, and effected.
Page 24, total 45
6) Update: Copy update file to U disk, and insert U disk to USB interface, Press 【Enter】key when cursor move to “system upgrade”, then system will be upgraded automatically, then device will be reboot automatically after MDVR updating success.
4.2.2 RECORD setup
Press 【Enter】key access to system setup menu.
Left column will shows submenu of RECORD when move cursor to Record setup.
Press Right ARROW key to enter record menu.
Press Down ARROW key to enter submenu of Record.
Press Right Arrow key to switch to the data entry area.
Press the Up or Down Arrow key to scroll through the entry fields
Press the Enter key to change the value or use the numeric keypad on the handheld
controller for data entry areas where the numeric values are used.
To save the changes, scroll to APPLY at the bottom screen and press ENTER.
Press Exit to quit without saving changes.
The RECORD menu consists of four tabs.
1)Record setup
Page 25, total 45
Page 26, total 45
a) Time insert: On/Off, press 【Enter】 key to input
b) File record size: 15/30/45/60 minutes, press 【Enter】 to input.
c) Storage overwrite: On/Off, press 【Enter】key to inport
d) Record mode: Ignition/Con/Manual/Alarm, press 【Enter】 to input.
e) Startup detection: On/Off, press 【Enter】key to import
Function: while at Record Mode, chosen” ON”, device will be at “standby” status, when at
specific time for recording(set at schedule), then device will be record, and will be shutdown
automatically after finishing record task.
f) Priority Record: On/Off, press 【Enter】key to input.
g) Pre-recording: On/Off, press 【Enter】 to input.
h) Duration: range is 1~60 minutes, enter with numberic keys
i) Record delay: 30~3600 second, enter with number keys.
j) Video System: PAL/NTSC, press 【Enter】to input
k) Lock save mode: user setup /Manual, Press 【Enter】to input
l) Lock save time: range is 2~60 days, enter with numberic keys
2)Channel setup
Page 27, total 45
Name: Press 【Enter】 key to enter keypad, same as System ID setting.
Qua. : Press 【Enter】key to select quality of record image, range is 1~8 level, “1” is for
the highest quality record image, and 8 for normal quality image.
Res: select between HD1 and CIF:
HD1: Resolution at 720x240(NTSC), 704x288(PAL).
CIF: Resolution at 360x240(NTSC), 352x288(PAL).
Fra: Press【Enter】to select frame rate ( frame per second)
Frame per second: 1~30 fps
Aud.: Press 【Enter】 to choice if each channel need to record audio
On: Need to record audio, Off: No need to record audio.
Rec: On/Off press 【Enter】to input.
Liveview
On: The camera allowed to liveview on screen.
OFF. The camera not allowed to liveview on screen, only show currect interface, or
back to login in screen when press”EXIT”.
Dual Encode:
ON: Allow to view monitoring screen at remote network monitor terminal
OFF: Not allow to view mornitoring screen at remote network monitor terminal.
Resolution for transmission: network transmission format, select between CIF and
QCIF, press 【Enter】key to input.
3)Alarm setup
Page 28, total 45
Parameter setup is same as channel settings.
Function: when occur alarm event, MDVR will record according this setting.
4)Schedule
Page 29, total 45
When Record mode is setup as “Con”, need to setup schedule, user can setup the
record time schedule as you wish, max can setup SIX periods per day.
Type: Con, Event,Alarm, MD,BD Press 【Enter】 to input
Con. Record is subject to time period and Startup/Shutdown Time setting, it is
belong to normal record.
Event subject to time period and Startup/Shutdown Time, when event triggerred,
the event log will be recorded.
Alarm record won’t subject to Time period and Startup/Shutdown Time, when
alarm is triggered, will record alarm video, when Pre-recording and Duration is
setting, will create record log.
MD and BD are subject to Time period and Startup/Shutdown Time setting, when
detect motion and block, will trigger video record.
Schedule has 9 items, each item for one day, and each item support two periods
Each item can be set as two unrepeatable period of time.
Every day: with effect to one week (seven days), and cannot be repeated with
other 8 items of time period settings.
Workday: with effect to working days schedule, cannot repeat with other working
days schedule setting.
Setup Workday start and end day as you wish, and press 【Enter】 to input.
Each period time enter with numberic keys, move cursor to specified time period, and
Page 30, total 45
then enter with number keys,
Period1 setting for first period of anyday of video record,
Period2 setting for second period of anyday of video record.
When setup as 00:00---23:59, it means 24 hours video record.
4.2.3 NETWORK setup
To move the cursor to the NETWORK setup and the left column is the NETWORK sub-
menu.
To move the cursor by pressing the up and down direction keys and select the relevant
sub-menu, cursor rightward to enter into the sub-menu and select the options to do
settings.
Move cursor to APPLY and press【Enter】key will save the settings, press 【Exit】will back
to submenu of GENERAL.
If not press【Enter】key and exit, then the modified setting will not been saved.
1) Local IP address
Page 31, total 45
IP address: move cursor to this option, Enter with number keys, the static IP address of
MDVR, it is used for update media server.
Mask: Move cursor to this option. Enter the subnet mask of MDVR.
Gateway: Enter the gateway of MDVR
MAC address: it is static, cannot be modified.
2)CMS server: cannot support right now.
Page 32, total 45
CMS IP: The IP address of CMS.
CMS port: CMS listen port, when connect with CMS server, this port setting must be
same as CMS server listen port.
Media Port: CMS server listen port, when connect with CMS, this setting must be same
as CMS media listen port.
4.2.4 ALARM
Press 【Enter】 key to enter system setup menu.
Move cursor to ALARM, the left volumn will shows submenu of ALARM
Enter the sunmenu is same as General setting.
ALARM is consist of two tabs..
1)Sensor
Page 33, total 45
Name: Connect 6 inputs of sensors S1~S6, user can defines their name
Press 【Enter】 key, then access into keypad interface.
Page 34, total 45
Enable : ON/OFF Press 【Enter】 key to input
Funtion: when Enable is Off, then the sensors signals will not be collected.
Type: Alarm/Event Press 【Enter】 key to input.
Alarm: Trigger alarm video record and alarm log.
Event: When occur event, will no record video, only record LOG when Enable is
on.
PWL ON/OFF, press 【Enter】key to input
OFF: High Leve will trigger alarm
ON: Low Level will trigger alarm.
Lock: Yes/No press 【Enter】 key to input
Function: lock record will not be delected automatically, the reserve time can be by
user.
2) Speed Setup
Enable: On/Off press 【Enter】key to input.
Alarm/Event: press 【Enter】key to input
Lock: Yes/No, press 【Enter】key to input.
Unit: km/h or mil/h, press 【Enter】 to input
Page 35, total 45
Current: The car current speed collected by GPS.
Prompt Limit: Enter with number keys, can be setup by user, the default setting is
80km/h.
Alarm Limit: Enter with number key, the default setting is 120km/h.
Doorswitch: Sensor detect interface for detecting door switch on/off.
D.O. max speed: Door on motion max speed. Enter with numberic key, can be
setup by user, the default setting is 5km/h.
Acc. Limit: Acceleration Alarm, enter with number keys.
4.3 Playback
Use Arrow key to select 【Enter】to accesss Playback menu,the following screen will
pop up:
The record search menu will show this monthe vide record information, the date with white color indicate
this day with video record.
Use ARROW keys and NUMBER keys to search video record.
Event Type: Press 【Enter】 to select search mode: All/ manual / Time /Alarm / MD/
Page 36, total 45
Ignition.
Year: Range is 2000 to 2099, only the last 2 digits of the year are changeable (ex.:03
for 2003), also could press + -, enter key to increase and decrease digits.
Month: Range 01~12 for the corresponding month number, also could use +,- Enter key
to increase and decrease digits.
Day: Range 01~31 for the corresponding day of the recording, also could use +,- Enter
to increase and decrease digits.
Hour: Range 01~23 for the appriopriate hour to begin the search, also could use
Mintues: Range 00~59 to narrow the search, also could use to increase and decrease
digits.
After entering the start time move cursor to the “Start” and press”Enter” on the handheld IR
controller. The recorded video history beginning at the time chosen will be listed on the
screen.
Use Arrow or 【+】、【-】key to select the video want to view, Press 【Enter】 to play video
file, and press 【EXIT】key to return to the previous Menu.
Page 37, total 45
4.4 Event Search
Move cursor to and press 【Enter】key to access system information menu, the
screen below will display:
Page 38, total 45
When search log information, them menu will display the information of record, the day with white color
means that this day with log record.
Use Arrow and number keys to search record data.
Type: Press 【Enter】key to select search way, all/sensor/operate/error/card
Sensor event means the signals collected by sensor.
Opearte event: to record users parameter modified operation.
Error&Alarm: Disk error or non-sensor colleted alarm event
Card event: Record the logs of card reader.
Year: Range is 2000 to 2099, only the last 2 digits of the year are changeable(ex:03 for
2003), also could use .+ -,enter key to increase and decrease digits.
Month: Range 01~12 for the corresponding month number,also could use +,- Enter key to
increase and decrease digits.
Day: Range 01~31 for the corresponding day of the recording, also could use +,- Enter
to increase and decrease digits.
Hour: Range 01~23 for the appriopriate hour to begin the search, also could use
Mintues: Range 00~59 to narrow the search, also could use to increase and decrease
digits.
After entering the start time move to the “Start” and press”Enter” on the handheld IR
controller. The recorded video history beginning at the time chosen will be listed on the
Page 39, total 45
screen.
Use ARROW Key to select the log file that want to view, press 【Enter】key to select the
log file (there will show a blue dot before log file), and press 【Enter】again, the blue dot will
disappear, means cancel the selected log file. After selecting log file, then can do export and
playback operation, when the log file with video file, then can playback, press 【EXIT】key to
return preview menu.
4.5 System information
Move cursor to and then press 【Enter】key to access system information menu, the
the below screen will be display:
Page 40, total 45
Version: This is the device firmware version number, it including firmware interface
information, media play type, software version No.
Memory information: It displays HDD capacity and the free spare of HDD.
GPS status: display if the device with or without GPS.
GPS signal status: it displays that if has GPS data currently.
Wirelss module: display if device have GPRS,CDMA/EDGE module.
SIM: display if with SIM card currently.
Page 41, total 45
5.Basic Working Parameter
Item Parameter Description
Input Voltage 8—36VInput voltage is +8V~+36V,when voltage is less than 8V or more than 36V for a long term, then device will shutdown automatically and enter into protection mode.
Output Voltage
12V(+/-0.2)Output Voltage is 12V(+/- 200mV),Maximum current
is 2A。
5V (+/-0.2)
Output Voltage is 5V(+/- 200mV),maximum current is
2A。Output all with overcurrent protection, when output current is more than 1.2 tims of maximum setting for a long term, Output will be cut off acutomatically, andl will be recovered when load get right.
Ignition signal0—2V Ignition off
5—36V Ignition On
Video input impendance
75Ω Each channel video input impendance is 75Ω。
Video output 900mV One channel outuput of 900 mV CVBS analog signals
Audio output power
12W Audio amplifier output maximum driven ability.
I/O interface0—2V Low voltage alarm
5V above High voltage alarm
RS232 port Reserved port, for expanding RS 232 device.
RS485 port Reserved port, for expanding RS485 device.
GPS interface connect with GPS antenna
GPRS interface
Connect with GPRS antenna.
Ethernet port Standard RJ45 interface, with indicator light.
HDD interface
USB interface1.Compatible with kinds of normal commercial U disk.2.Hot swap, when device indicates file transfer finished,
remove U disk will not damage video file data.working temperature
-25----60℃ The working circumstance temperature at good ventilation condition
Page 42, total 45
6. Appearance and interface
P1 Overview——Movable HDD bay
P2 Overview----The front
Page 43, total 45
图1
P3 Overview----The rear
7. Unit Wiring
Lable connecter Description Details
power input connection cable
Three leads vehicle power supply connector
Red is positive wire, black is negative wire, Yellow is connect with vehicle ignition
Red connects with vehicle positive terminal of the battery.Black connects with vehicle negative terminal of the battery.Yellow connects with。
+12V OUTTwo RED wires, two black wires
Red is output positive, and black is negative
Positive with special fuse.
V IN0—3 BNC connector Yellow Video input.
CVBS OUT BNC connector Yellow Video output.
A IN0—3 BNC connector Red Audio input
L OUT BNC connector Red Audio output
ALARM IN1—6Green, Black is GND Alarm, Event input, each two
alarm use one GND.
ALARM OUT1--2 Blue, Black is GND Alarm, Event output.
RS485Yellow is 485-AWhite is 485-B
RS485-1 and RS485-2 two group.
RS232 Green is TXYellow is RXBlack is GND
Has A、B、C three group
+5V OUT Palm With special fuse.
GPS four leads wire Black Connect with external GPS.
Page 44, total 45
square plug
GPRS antennaSMA Bulkhead Straight Clamp Crimp Plug
Black Connect with GPRS port.
Page 45, total 45