Higher Order Surfaces in OpenGL with NV_evaluators Cass Everitt [email protected].
Produced by Khodr Hussein Drafting Teacher Cass Technical High School Detroit Michigan
description
Transcript of Produced by Khodr Hussein Drafting Teacher Cass Technical High School Detroit Michigan
1. Identify and use the tools needed2. Secure the paper to the drawing board3. Draw the Border Lines4. Draw the Title Block with guidelines5. Add details and information in the title
block6. Understand the properties of the Working
Area
Straight Edge
Equipments you need: Drafting Board
Triangle
TriangleTriangle8.5 x 11
White paper
Drafting pencilsRuler
DraftingTape
1. Identify and use the tools needed2. Secure the paper to the drawing board3. Draw the Border Lines4. Draw the Title Block with guidelines6. Add details and information in the title block7. Understand the properties of the Working
Area
Straight Edge
2. Secure the paper to the drawing board
2.1 First: Place the Straight edge few inches above the bottom edge of the Drawing Board
Straight-Edge
2. Secure the paper to the drawing board2.2 Next: align the bottom edge of the paper to the top edge of the Straight-Edge
8.5 x 11White paper
Tip: you may roll up the two bottom corners of the paper so it would not slide under the edge
Next
Straight-Edge
2. Secure the paper to the drawing board2.3 Now: Tape both top edges of the paper
8.5 x 11White paper
tip: Keep the tape closer to the corner to allow for drawing the border lines.
Next
2. Secure the paper to the drawing board2.4 Finally: Tape both bottom edges of the paper
8.5 x 11White paper
Straight Edge
1. Identify and use the tools needed2. Secure the paper to the drawing board3. Draw the Border Lines4. Draw the Title Block with guidelines6. Add details and information in the title
block7. Understand the properties of the Working
Area
3. Draw the Border Lines3.1 First: using the Ruler, measure ½” from left edge of the paper
Straight Edge
½”
Tip: align the ruler with the straight edge and then place a light dash parallel to the edge on the ½” mark
Next
3. Draw the Border Lines3.2 Next: Draw a vertical line on the ½” mark
Straight Edge
½”Triangle
Note : This line must be very light
Next
Tip: draw line from top to bottom
3. Draw the Border Lines3.3 Measure ½” from right edge of the paper
Straight Edge
½” ½”Triangle
3. Draw the Border Lines3.4 Measure ½” from Top edge of the paper
Straight Edge
½” ½”½
”
Tip:Keep all lines light until you are instructed to darken
Next
3.5 Now Draw the Top Border Line
3. Draw the Border Lines3.6 Measure ½” from Bottom Edge of the paper
Straight Edge
½” ½”½
”
Next
3.7 Now Draw the BottomBorder Line
½”
1. Identify and use the tools needed2. Secure the paper to the drawing board3. Draw the Border Lines4. Draw the Title Block with guidelines6. Add details and information in the title block7. Understand the properties of the Working
Area
4. Draw the Title Block with guidelines4.1 Measure ½” from Bottom Border line
Straight Edge½
”
Next
4.2 Now Draw the top of the Title Block
Straight EdgeNext
4. Draw the Title Block with guidelines4.3 Now Layout the measurements for the guidelines
1/16 “1/8“
1/8“
1/8“1/16 “
½”
Next
4.4 Draw the guidelines4. Draw the Title Block with guidelines
Remember the measurements
4.5 Now draw the title block section dividers
3” 4” 3”
1. Identify and use the tools needed2. Secure the paper to the Drawing Board3. Draw the Border Lines4. Draw the Title Block with Guidelines6. Add details and information in the Title Block7. Understand the properties of the Working Area
½”
Next
6.1 Start with your Name in the Top Left Section
6. Add details and information in the Title Block
6.2 Add the Class, and the Semester under Name
3” 4” 3”
6.3 Add the Name of the Drawing in the Top Middle6.4Add the Topic Section under drawing Name6.5 Add the Date in the Top of End Section6.6 Add Teacher Name in Bottom End Section
JOHN DOEDRAFTING I
PREPARING WORK AREABASIC PROCEDURES
12/12/3001MR SEAN DOE
½”
Next
`You may darken necessary lines now
6. Add details and information in the Title Block
3” 4” 3”JOHN DOE
DRAFTING IPREPARING WORK AREABASIC PROCEDURES
12/12/3001MR SEAN DOE
Or wait until you fininsh the assigned drawing so you do not cause lead smudges while drawing
Next
1. Identify and use the tools needed2. Secure the paper to the Drawing Board3. Draw the Border Lines4. Draw the Title Block with Guidelines6. Add details and information in the Title Block7. Understand the properties of the Working Area
LENTH
½”
Next
7. Understand the properties of the Working Area
JOHN DOEDRAFTING I
PREPARING WORK AREABASIC PROCEDURES
12/12/3001MR SEAN DOE
Next
Length of the Working Area (LWA)
10”
Wid
th o
f th
e W
ork
ing
Are
a ( W
WA
)7”Given the Border Lines and
the Title Block, Always Remember:The Working Area has the following measurements
LWA = 10”WWA = 7”
The End