pro-partDecorative profile for ceramic wall tiles. It is an alternative to the traditional ceramic frieze. Suitable for trimming corners and transitions between ceramic tiles.

pro-part is a right angle, corner shaped profile, with an 8 mm edge and another edge with variable width depending on the tile thickness. This design makes pro-part a very versatile profile, with a wide range of applications in ceramic installations. It is the simplest solution for all kind of trims for ceramic wall tiles in which you need to cover the tile edges. Its design with sleek, straight lines, makes this profile specially recommended for rectified ceramics.

Recommended use - Decorative line in ceramic wall tiles.

- Separation of wall tiles with different designs or formats.

- Right angle trim for wall corners.

- Right angle trim for wall tiles: frames, corbels or low brick walls.

- Transition at same level between different floor tile types.

- Trim for ceramic floor tiles.

- Stair steps.

- Floor decoration.

- Residential and public use.

- Permanently damp environments and direct contact with water.

- Outdoors, use pro-part inox

- Do not use in pools.

Materials - Anodized aluminium.

- Lacquered aluminium.

- V2A-type stainless steel.

- Gloss polished brass.

- Chromed brass.

Substrates - All substrates suitable for ceramic tiles laying.

- A suitable substrate for laying ceramics with the thin-bed method must be clean, dry, compact, with a rough texture and flat (deviations inferior to 3 mm every 2 m of surface).

Data sheet

pro-part

Features - 8 mm edge

- 90º angle finish

- Side flange to ease installation.

- Having no ledges, it can be laid in direct contact with the profile. Especially recommended for recti-fied tiles.

- Easy to cut with every tile layer’s everyday tools.

- There are special pieces for corners, which avoid having to miter the profile.

- This profile is also supplied in rods with a special die which can be flexed and curved.

Profile types

pro-part anodized aluminiumAluminium profile manufactured by extrusion and anodized chemical treatment.

Its cost-effectiveness makes this profile the best solution for all kinds of projects.

- Features:

• Silver / Gold

• Matt and gloss

• Floor / Wall

• Indoor / Outdoor.

- The anodization treatment protects aluminium from rust and limits scratches.

- Protect from any abrasive element which could scratch the exposed profile surface.

- Anodized aluminium profiles are sensible to the combination of dampness and alkaline products like cement mortars. It is recommended to be extremely careful when installing them. Avoid contact with cement mortars as far as possible an clean any mortar stain which affects the exposed edge of the profile as soon as possible.

pro-part lacquered aluminiumAluminium profile manufactured by extrusion and gloss lacquered.

Specially recommended in corners and trims in which you need a profile with the same finish as the ceramics.

- Features:

• Gloss

• Wall tile

• Indoor / Outdoor.

- Protect from any abrasive element which could scratch the exposed profile surface.

- Before installing, check that the profile finish matches with that of the tile.

pro-part stainless steelStainless steel profiles are produced by folding, so their shape is slightly different to that of aluminium or brass profiles. Angles and shapes will always have a rounded finish.

Profiles made of V2A stainless steel are highly resistant both to mechanical stress and chemical attack. Specially recommended outdoors.

- Features:

• Matt

• Floor / Wall

• Indoor / Outdoor.

- The profile is supplied with a plastic film protecting it during installation. Once the profile installed, peel off the film with a cutter.

- Not recommended for use in pools or any other use in direct contact with concentrated chemicals. In any case, we recommend you perform a previous test to check its suitability.

pro-part gloss polished brassBrass profile manufactured by extrusion and gloss polished.

High resistance to mechanical stress. Specially recommended for polished natural stone floors and commercial ceramic floors.

- Features:

• Gloss

• Floor / Wall

• Indoor / Outdoor.

- High resistance to mechanical stress.

- Brass profiles react in contact with air, producing a rust layer which alters the profile’s surface color. This alteration increases with the action of many chemicals or water.

- Brass profiles can undergo superficial polishing, recovering color, appearance and even the initial gloss.

pro-part chromed brassBrass profile manufactured by extrusion, chrome plated and gloss polished.

High finish and gloss profile. Specially recommended for decorating indoor wall tiles.

- Table:

• Gloss

• Floor / Wall

• Indoors.

- Protect from any abrasive element which could scratch the exposed profile surface.

pro-part

pro-part flexpro-part profile with a special die which can be flexed and curved.

Curve radii:

- Anodized aluminium silver. 75 cm for an 8 mm high profile.

- Anodized aluminium gold. 75 cm for an 8 mm high profile.

- Gloss polished brass. 75 cm for an 8 mm high profile.

pro-part corner - Anodized aluminium silver.

- V2A stainless steel.

- Chromed brass.

Instructions for use - Choose the profile according to the tile thickness. We recommend to choose a profile at least 1 mm

thicker than the tile.

- Lay the tile with the thin-bed method, with adhesive and a notched trowel.

- Press the profile flange on the adhesive and check that it is covered by the bonding material.

- Level the profile with the tile. Do not leave the profile above the tile level.

- As a general rule, we recommend to leave 1 mm joint between the profile and the tile. In stable substrates with no movement risk, a minimum joint can be used.

- Before sealing the tiling joints, check that the grouting material chosen does not scratch nor chemi-cally alters the profile surface. If it does, cover the profile with protective tape.

- Fill completely the joint between tile and profile with grouting material. Never let the grouting material harden on the profile.

Never use metallic tools or abrasive elements which can scratch the profile surface.

Cut the profile with a hand saw or with a circular saw with a suitable disc. Be extremely cautious when cutting stainless steel profiles.

Cleaning and maintenance - These profiles do not need cleaning and maintenance different from the tiles in which they are

installed.

- Use neutral cleaning products. Do not use products containing hydrochloric or hydrofluoric acid. In any case, we recommend you perform a previous test before use.

- Do not use abrasive or metallic elements which can scratch the profile surface.

- Gloss polished brass profiles can be polished once installed, recovering their original features. A normal metal polish can be used.

pro-part

Technical Sheet Conditions - This is not a finished product technical sheet. It belongs to a product which, together with others, is

the base of a ceramic tile laying system with which professionals perform their job. Instructions in this technical sheet have been written based on our experience and technical expertise, but they have to be considered as general recommendations, which together with those for the rest of the products in the system, help the professionals in their job.

- As it is not possible to know all the features and conditions of a building job, professionals must consider it and, if deemed appropriate, perform a previous test to confirm whether the product is sui-table for the job. Specially recommended in applications which imply mechanical stresses or chemical reactions not described in this technical sheet.

- The technical sheet cannot reflect all the applications and conditions entailed in the use of a material, so, in situations not described in this sheet, we recommend to perform a previous test and refer to our technical department.

- This sheet has been updated in January, 2013.

pro-part

pro-part

pro-part

Profile length: 2500 mm Minimum packaging: 10 profiles

pro-part

KEA SAP h (mm)B73141317 100089004 11B73124004 100005353 12.5

Anodized aluminium gloss silver

KEA SAP h (mm)B73141009 100005377 9B73141010 100005378 11B73141011 100005379 12.5

Stainless steel

KEA SAP h (mm)B73122001 100005322 XLIGHT 7B73122002 100005323 9B73122003 100005324 11B73122004 100005325 12.5B73122005 100005326 15B73122006 100005327 20B73122007 100005328 25

Anodized aluminium silver

KEA SAP h (mm)B73122009 100005330 9B73122010 100005331 11B73122011 100005332 12.5B73122014 100005335 25

Anodized aluminium gold

KEA SAP h (mm)B73134001 100005368 XLIGHT 7B73134002 100005369 9B71342552 100088905 10B73134003 100005370 11B73134004 100005371 Shade 1 12.5B73141312 100033129 Shade 2 12.5B73134005 100005372 15

Chromed brass

KEA SAP h (mm)B73122301 100005336 XLIGHT 7B73122302 100005337 9B73122303 100005338 11B73122304 100005339 12.5

Anodized aluminium silver corner

KEA SAP h (mm)B73134301 100005373 XLIGHT 7B73134302 100005374 9B71342554 100091065 10B73134303 100005375 11B73134304 100005376 12.5B71342541 100067718 15

Chromed brass corner

KEA SAP h (mm)B73141309 100005380 9B73141310 100005381 11B73141311 100005382 12.5

Stainless steel corner

pro-part stainlessh

8 mm

pro-parth

8 mm

pro-partcorner

KEA SAP h (mm)B73132003 100005363 11B73132004 100005364 12.5

Gloss polished brassKEA SAP h (mm)B71342551 100088551 Negro 11B71342547 100080530 Negro 12.5

B71342576 100100723 White 11B71342549 100083438 White 12.5

Lacquered aluminium

pro-part

Longitud del perfil: 2500 mm Embalaje mínimo: 10 perfiles

KEA SAP h (mm)B73232003 100005413 11B73232004 100005414 12,5B73232005 100005415 15

Flex gloss polished brass

KEA SAP h (mm)B73222001 100005390 7B73222002 100005391 9B73222003 100005392 11B73222004 100005393 12,5B73222005 100005394 15B73222006 100005395 20

Flex anodized aluminium silverKEA SAP h (mm)B73222010 100005399 11B73222011 100005400 12,5

Flex anodized aluminium Gold

butech building technology, S.A.Carretera Villarreal - Puebla de Arenoso (cv-20) km 2,5 - 12540 Villarreal - Castellón - España.

Apartado de correos: 297 - Teléfono (+34) 964 53 62 00 - Fax (+34) 964 53 00 34 - butech@butech.es - http://www.butech.es

Data sheet

Gold CollectionDecorative profiles for wall tiles, 24K gold plated. They perfectly match ceramics and give distinction and elegance to the most exclusive bathroom settings. It is an alternative to the traditional ceramic frieze. Suitable for trimming corners and transitions between ceramic tiles.

This type of profiles features square angle finishes, which allows for a no joint perfect fit with rectified ceramic tiles. Its design with sleek, straight lines, makes this profile specially recommended for the most luxurious settings.

Recommended use: - Decorative line in ceramic wall tiles.

- Separation of wall tiles with different designs or formats.

- Right angle trim for wall corners.

- Right angle trim for wall tiles: frames, corbels or low brick walls.

- Residential and public use.

- Permanently damp environments and direct contact with water.

- Do not use for floor tiles.

- Do not use in outdoor walls or pools.

Materials - 24K gold plated brass.

Substrates - All substrates suitable for ceramic tiles laying.

- A suitable substrate for laying ceramics with the thin-bed method must be clean, dry, compact, with a rough texture and flat (deviations inferior to 3 mm every 2 m of surface).

Features

pro-mate 5 - 5 mm side edge.

- 90º angle finish

- Side flange to ease installation.

- Having no ledges, it can be laid in direct contact with the profile. Especially recommended for recti-fied tiles.

pro-part - 8 mm side edge.

- 90º angle finish

- Side flange to ease installation.

- Having no ledges, it can be laid in direct contact with the profile. Especially recommended for recti-fied tiles.

Gold Collection

pro-part Li - Both sides of the profile have exactly the same length.

- Side edges in 9, 10, 11 or 12.5 mm.

- 90º angle finish

- Side flange to ease installation.

- Having no ledges, it can be laid in direct contact with the profile. Especially recommended for recti-fied tiles.

Certifications/Standards:Corrosion tests in artificial atmosphere or salt spray test (UNE-EN-ISO 9227) have been performed.

After 200 hours of test, no defects, cracks of traces of rust are observed.

Profile types

Gold plated brassBrass profiles, made by extrusion and 24K gold electroplating. Depending on the profile, a final polishing is performed to achieve a gloss finish.

High finish and gloss profile. Specially recommended for decorating indoor wall tiles.

- Features:

• Matt/Gloss.

• Wall tile

• Indoors.

- Protect from any abrasive element which could scratch the exposed profile surface.

Instructions for use - Choose the profile according to the tile thickness. We recommend to choose a profile at least 1 mm

thicker than the tile.

- Lay the tile with the thin-bed method, with adhesive and a notched trowel.

- Press the profile flange on the adhesive and check that it is covered by the bonding material.

- Level the profile with the tile. Do not leave the profile above the tile level.

- As a general rule, we recommend to leave 1 mm joint between the profile and the tile. In stable substrates with no movement risk, a minimum joint can be used.

- Before sealing the tiling joints, check that the grouting material chosen does not scratch nor chemi-cally alters the profile surface. If it does, cover the profile with protective tape.

- Fill completely the joint between tile and profile with grouting material. Never let the grouting material harden on the profile. Be extremely cautious when applying and cleaning grout.

- Never use metallic tools or abrasive elements which can scratch the profile surface.

- Cut the profile with a hand saw or with a circular saw with a suitable disc. Be extremely cautious when cutting stainless steel profiles.

Cleaning and maintenance - These profiles do not need cleaning and maintenance different from the tiles in which they are

installed.

- Use neutral cleaning products. Do not use products containing hydrochloric or hydrofluoric acid. In any case, we recommend you perform a previous test before use.

- Do not use abrasive or metallic elements which can scratch the profile surface.

Data Sheet Conditions - This is not a finished product technical sheet. It belongs to a product which, together with others, is

the base of a ceramic tile laying system with which professionals perform their job. Instructions in this technical sheet have been written based on our experience and technical expertise, but they have to be considered as general recommendations, which together with those for the rest of the products in the system, help the professionals in their job.

- As it is not possible to know all the features and conditions of a building job, professionals must consider it and, if deemed appropriate, perform a previous test to confirm whether the product is suit-able for the job. Specially recommended in applications which imply mechanical stresses or chemical reactions not described in this technical sheet.

- The technical sheet cannot reflect all the applications and conditions entailed in the use of a material, so, in situations not described in this sheet, we recommend to perform a previous test and refer to our technical department.

- This sheet has been updated in January, 2013.

Gold Collection

Gold Collection

Gold Collection

Profile length: 2500 mm Minimum packaging: 10 profiles

pro-mate 5

KEA SAP h (mm) PriceB71342573 100100722 12.5 mm 91.35 €/uB71342572 100100721 11 mm 90.20 €/u

KEA SAP h (mm) PriceB71342575 100100725 12.5 mm 94.45 €/u B71342577 100100724 11 mm 92.05 €/u

KEA SAP h (mm) PriceB71342578 100100762 12.5 mm 102.50 €/uB71342574 100100726 11 mm 98.65 €/u

24K Gold

h

5 mm

pro-mate 5

pro-part pro-parth

8 mm

24K Gold

pro-part Li24K Gold

pro-part Li h

h

butech building technologies, S.A.Carretera Villarreal - Puebla de Arenoso (cv-20) km 2,5 - 12540 Villarreal - Castellón - España.

P.O. Box: 297 - Telephone (+ 34) 964 53 62 00 - Fax (+ 34) 964 53 00 34 - butech@butech.es - http://www.butech.es.

Data sheet

Metal CollectionDecorative profiles for ceramic wall tiles, with special metallic finishes. It is an alternative to the tradition-al ceramic frieze. Suitable for trimming corners and transitions between ceramic tiles.

This type of profiles features a special metallic finish for each profile, obtained with electroplating, and a square angle shape, which allows for a no joint perfect fit with rectified ceramic tiles. Specially recom-mended for laying rectified wall tiles.

Recommended use: - Decorative line in ceramic wall tiles.

- Separation of wall tiles with different designs or formats.

- Right angle trim for wall corners.

- Right angle trim for wall tiles: frames, corbels or low brick walls.

- Residential and public use.

- Permanently damp environments and direct contact with water.

- Do not use for floor tiles.

- Do not use in outdoor walls or pools.

Materials - Electroplated brass.

Substrates - All substrates suitable for ceramic tiles laying.

- A suitable substrate for laying ceramics with the thin-bed method must be clean, dry, compact, with a rough texture and flat (deviations inferior to 3 mm every 2 m of surface).

Features

pro-mate 5 - 5 mm side edge.

- 90º angle finish

- Side flange to ease installation.

- Having no ledges, it can be laid in direct contact with the profile. Especially recommended for recti-fied tiles.

pro-part - 8 mm side edge.

- 90º angle finish

- Side flange to ease installation.

- Having no ledges, it can be laid in direct contact with the profile. Especially recommended for recti-fied tiles.

Metal Collection

Profile types

Electroplated brassBrass profile manufactured by extrusion and electroplating. Depending on the profile, a final polishing is performed to achieve a gloss finish.

Profile with metallic finish. Specially recommended for decorating the trendiest ceramic tiles.

- Features:

• Matt/Gloss.

• Wall tile

• Indoors.

- Protect from any abrasive element which could scratch the exposed profile surface.

Instructions for use - Choose the profile according to the tile thickness. We recommend to choose a profile at least 1 mm

thicker than the tile.

- Lay the tile with the thin-bed method, with adhesive and a notched trowel.

- Press the profile flange on the adhesive and check that it is covered by the bonding material.

- Level the profile with the tile. Do not leave the profile above the tile level.

- As a general rule, we recommend to leave 1 mm joint between the profile and the tile. In stable substrates with no movement risk, a minimum joint can be used.

- Before sealing the tiling joints, check that the grouting material chosen does not scratch nor chemi-cally alters the profile surface. If it does, cover the profile with protective tape.

- Fill completely the joint between tile and profile with grouting material. Never let the grouting material harden on the profile. Be extremely cautious when applying and cleaning grout.

Never use metallic tools or abrasive elements which can scratch the profile surface.

Cut the profile with a hand saw or with a circular saw with a suitable disc. Be extremely cautious when cutting stainless steel profiles.

Cleaning and maintenance - These profiles do not need cleaning and maintenance different from the tiles in which they are

installed.

- Use neutral cleaning products. Do not use products containing hydrochloric or hydrofluoric acid. In any case, we recommend you perform a previous test before use.

- Do not use abrasive or metallic elements which can scratch the profile surface.

Data Sheet Conditions - This is not a finished product technical sheet. It belongs to a product which, together with others, is

the base of a ceramic tile laying system with which professionals perform their job. Instructions in this technical sheet have been written based on our experience and technical expertise, but they have to be considered as general recommendations, which together with those for the rest of the products in the system, help the professionals in their job.

- As it is not possible to know all the features and conditions of a building job, professionals must consider it and, if deemed appropriate, perform a previous test to confirm whether the product is suit-able for the job. Specially recommended in applications which imply mechanical stresses or chemical reactions not described in this technical sheet.

- The technical sheet cannot reflect all the applications and conditions entailed in the use of a material, so, in situations not described in this sheet, we recommend to perform a previous test and refer to our technical department.

- This sheet has been updated in January, 2013.

Metal Collection

Metal Collection

pro-part ocean pro-mate 5 ocean

pro-part moon pro-mate 5 moon

pro-part graphite pro-mate 5 graphite

pro-part oxyde pro-mate 5 oxyde

pro-part line

Metal Collection

Profile length: 2500 mm Minimum packaging: 10 profiles

pro-mate 5

KEA SAP h (mm)B71342594 100120363 11 mm

KEA SAP h (mm)B71342595 100120370 11 mm

KEA SAP h (mm)B71342592 100120362 11 mm

KEA SAP h (mm)B71342591 100120369 11 mm

KEA SAP h (mm)B71342598 100120359 11 mm

KEA SAP h (mm)B71342590 100120359 11 mm

KEA SAP h (mm)B71342602 100120360 11 mm

KEA SAP h (mm)B71342593 100120367 11 mm

KEA SAP h (mm)B71342599 100120364 11 mm

KEA SAP h (mm)B71342599 100120371 11 mm

Ocean

Ocean

Moon

Moon

Graphite

Graphite

Line

Line

Oxyde

Oxyde

h

5 mm

pro-mate 5

pro-part pro-parth

8 mm

butech building technologies, S.A.Carretera Villarreal - Puebla de Arenoso (cv-20) km 2,5 - 12540 Villarreal - Castellón - España.

P.O. Box: 297 - Telephone (+ 34) 964 53 62 00 - Fax (+ 34) 964 53 00 34 - butech@butech.es - http://www.butech.es.