E x p a n s io n & B u s in e s s D e v e lo p m e n t S ...
Prezentacja programu PowerPoint - Begoresdi r e c ti o n to s h or t th e c o n ta c ts o n th e s e...
Transcript of Prezentacja programu PowerPoint - Begoresdi r e c ti o n to s h or t th e c o n ta c ts o n th e s e...
CONTROLSYSTEMSFOR YOUR NEEDS
SALUS Smart Home – system components
WATER LEAK SENSOR
Features:• Waterproof• Wireless connectivity (ZigBee)• Small size• LED diode - indicates the device status• Many assembly possibilities through the accessories
included in the kit
Power Supply 3 V (CR2 battery)
Length of the external sensor 2 m
Sensor dimensions [mm] H=25, Ø=55
Housing dimensions [mm] 60 x 66 x 30
This sensor was created to detect leaks in plumbing installations.
SALUS Smart Home
Water leak sensor helps to minimize the damages and potential renovation costs caused by flood (flooded rooms/equipment).
It informs about plumbing installation failure, floods, roof leaks, etc.
Water leak sensors can be a good complement of an expanded alarm system (monitoring, alarming).
Feel safe
Examples of use:
Bathroom Kitchen Boiler room Warehouse Archive room Production hall
Water leak sensor is part of the SALUS Smart Home system, thanksto it we have access to an infinite number of configurations andapplication options.
System can prevent losses by cutting off the water supply usingdevices like SR600 or SPE600.
It is also possible to send notifications (SMS, e-mail) at the timewhen an alarm is triggered by the water leak sensor.
SALUS Smart Home
SALUS Smart Home – komponenty systemu
1. Water leak sensor contacts areshorted by liquid
2. Sensor sends a signal to the UGE600gateway
3. The UGE600 gateway sends an SMS notification and closes the valve by SPE600 Smart Plug
Example of use:
WATER LEAK SENSOR
SALUS Smart Home
Water leak sensor set contains:
Water leak sensor
Holder
External sensor
Mountingaccessories(screws + self-adhesive tape)
+ Manual Instruction
1.
SALUS Smart Home
Many assembly possibilities:
As a standalone water leak sensor
Contacts for leak detection
2.
SALUS Smart Home
Many assembly possibilities:
Water leak sensor + holder
Contacts for leak detection
+ =
Contacts for leak detection
2.
SALUS Smart Home
Many assembly possibilities:
Water leak sensor + holder
Version 1
Installation/Quick Start Guide: Water Leak Sensor (SS901ZB) Visit www.salusinc.com for the User Manual
In the Box Tools Needed Note:
Additional equipment may be required due to building construction or materials, or other radio interference that may reduce the radio range.
Water Leak Sensor w/ Battery (1x CR2, 3V Lithium)
Stand Sensor Cable Installation/ Quick-start Guide
Screws and Anchors Adhesive Pad #1 Phillips Screwdriver
PAIRING INSTRUCTIONS • Follow your system ’s instructions to prepare to add devices to the
system.
• Remove the Face Plate from the sensor by turning the Face Plate
counter-clockwise and pull the battery tab to start the pairing
process.
• When the sensor is detected and added to the system, replace the
Face Plate by aligning the dots and turning the Face Plate clockwise.
• Make sure the dots are fully aligned for a proper seal, then proceed
to the sensor installation.
INSTALLATION INSTRUCTIONS • Identify a level surface for the sensor, where water will likely
accumulate in the event of a leak. If the sensor is too wide for
placement at the desired location, the stand can be used for a
narrower profile.
For tighter
locations or
locations with
radio problems,
use the
included
Sensor Cable.
INSTALLING THE SENSOR CABLE (OPTIONAL) • To install the Sensor Cable, first run the cable to the desired location,
and fasten the winged end of the Sensor Cable into place. Note that
the tips are angled to improve the sensing ability when the tips are
near a surface.
• Insert the square end of the Sensor Cable into the terminals on the
stand.
• Screw down both terminals until the cable is firmly held in place
• Mount the Stand to the wall or other surface using the supplied
double-sided adhesive pad or screws.
• Insert the Water Leak Sensor into the stand to begin operation.
TESTING THE SENSOR • To test the sensor, remove it from the stand or floor
• Insert the sensor into the stand 90 degrees from upright in either
direction to short the contacts on the sensor.
• The sensor will send a message to the connected home system
indicating a water leak. The LED will not light up to preserve battery
life.
REPLACING THE BATTERY (Use only Panasonic CR2 3V lithium battery)
• Grasp the top of the sensor Face Plate, rotate counter-clockwise
and lift from the sensor Body.
• Grasp the battery from both ends and lift to remove the battery
from the sensor.
• Insert a new battery into the sensor, observing the proper polarity.
• Position the sensor Face Plate over the Sensor Body, aligning the
dots on the Face Plate and Body, then rotate clockwise to align the
dots again to close.
Surface Install Sump Install
3.
SALUS Smart Home
Many assembly possibilities:
Water leak sensor + holder + external sensor
+
Contacts for leak detection
External sensor input
3.
SALUS Smart Home
Many assembly possibilities:
Water leak sensor + holder + external sensor
Version 1
Installation/Quick Start Guide: Water Leak Sensor (SS901ZB) Visit www.salusinc.com for the User Manual
In the Box Tools Needed Note:
Additional equipment may be required due to building construction or materials, or other radio interference that may reduce the radio range.
Water Leak Sensor w/ Battery (1x CR2, 3V Lithium)
Stand Sensor Cable Installation/ Quick-start Guide
Screws and Anchors Adhesive Pad #1 Phillips Screwdriver
PAIRING INSTRUCTIONS • Follow your system ’s instructions to prepare to add devices to the
system.
• Remove the Face Plate from the sensor by turning the Face Plate
counter-clockwise and pull the battery tab to start the pairing
process.
• When the sensor is detected and added to the system, replace the
Face Plate by aligning the dots and turning the Face Plate clockwise.
• Make sure the dots are fully aligned for a proper seal, then proceed
to the sensor installation.
INSTALLATION INSTRUCTIONS • Identify a level surface for the sensor, where water will likely
accumulate in the event of a leak. If the sensor is too wide for
placement at the desired location, the stand can be used for a
narrower profile.
For tighter
locations or
locations with
radio problems,
use the
included
Sensor Cable.
INSTALLING THE SENSOR CABLE (OPTIONAL) • To install the Sensor Cable, first run the cable to the desired location,
and fasten the winged end of the Sensor Cable into place. Note that
the tips are angled to improve the sensing ability when the tips are
near a surface.
• Insert the square end of the Sensor Cable into the terminals on the
stand.
• Screw down both terminals until the cable is firmly held in place
• Mount the Stand to the wall or other surface using the supplied
double-sided adhesive pad or screws.
• Insert the Water Leak Sensor into the stand to begin operation.
TESTING THE SENSOR • To test the sensor, remove it from the stand or floor
• Insert the sensor into the stand 90 degrees from upright in either
direction to short the contacts on the sensor.
• The sensor will send a message to the connected home system
indicating a water leak. The LED will not light up to preserve battery
life.
REPLACING THE BATTERY (Use only Panasonic CR2 3V lithium battery)
• Grasp the top of the sensor Face Plate, rotate counter-clockwise
and lift from the sensor Body.
• Grasp the battery from both ends and lift to remove the battery
from the sensor.
• Insert a new battery into the sensor, observing the proper polarity.
• Position the sensor Face Plate over the Sensor Body, aligning the
dots on the Face Plate and Body, then rotate clockwise to align the
dots again to close.
Surface Install Sump Install Flat surface assembly Assembly by cable tie
For more information on SALUS Controls products, please visit:
www.salus-controls.euand www.it600.eu