PRESSURE REGULATORS, FLOW METERS, -...

PRESSURE REGULATORS, FLOW METERS, QUICK COUPLING PROBES AND ACCESSORIES

TABLE OF CONTENTS

3

13485QUALITYASSURANCE

ISO0029

INTRODUCTION P.004

- CEODEUX MEDITEC solutions P.004

- Quality first... P.004

- The main medical gases P.005

PRODUCT RANGE OVERVIEW P.006

PRESSURE REGULATORS | STANDARD RESPIRATORY THERAPIES P.008

- ALPINOX medical oxygen regulator P.008

- MINIOX medical oxygen regulator P.010

PRESSURE REGULATORS | SPECIAL THERAPIES (ASSISTED) P.012

- Series BSC 280/380 P.012

- Series BSC 290/390 P.014

- Series DI 135 P.016

IN-HOSPITAL THERAPY EQUIPMENT P.018

- M730 | Alpi-flow Flowmeter with calibrated orifices P.018

- Alpinox Column Flowmeter P.019

- ALPI-VAC | vaccum regulator P.020

- Alpi-vent | suction units P.021

ACCESORIES P.022

- Respiratoty therapy accessories P.022

- Suction accessories P.023

All Rotarex regulators are produced in Europe in accordance with international standards (ISO; CGA....) and are guaran-teed to provide safe and reliable performance in operation. All locations are ISO 13485.

CEODEUX MEDITEC SOLUTIONS

QUALITY FIRST...

4 INTRODUCTION

ALL RIGHTS OF CHANGE RESERVED

Patient therapy and safety is our main focus in the design, installation, commissioning and operation of medical gas equipment

QUANTITY OF SUPPLYRegulators are designed in such a way sufficient medical gas capacity can be ensured in order to provide the required pressures and flows of gases for the intended number of patients to be treated at any time.

IDENTITY OF SUPPLYAll our products are designed, produced and controlled for a specific medical gas. All points to which the user or technical staff can connect are gas specified. There is no risk of misconnection.

QUALITY OF SUPPLYOur regulators maintain quality of supplied medical gases thanks to appro-priate selection of material, components cleanliness and internal filtration equipment.Products designs ensure safe supply by minimizing ignition risks, by avoid-ing patient poisoning risks and by guaranteeing very good performances for accurate therapies.

CEODEUX MEDITEC products are designed, validated, produced and con-trolled during their whole lifetime according to a very stringent quality system which exceeds requirements of ISO 13485 standard.

DESIGNAll our products comply with local and international standards. Some reference standards:

Product design is done through a risk assessment process and is combining proven technologies and innovation to reach the best performance levels.

VALIDATIONProduct validation process guarantees that products are developed and produced to withstand the complete lifecycle (installation, commission-ing, normal service and maintenance)

PRODUCTIONAll products are produced in a controlled environment in order to maintain cleanlinessAn individual traceability is ensured with individual serial numberProducts are individually controlled and data are recorded for a perfect product management.All products are cleaned according to ISO 15001

Products design and validation

CGA E-7 Medical gas pressure regulators Flowmeters and orifice flow selectors

ISO 10524-1 Pressure regulators for use with medical gases - Part 1: Pressure regulators and pressure regulators with flow-metering devices

ISO 15002 Flowmeters for use with medical gases

Materials selection and cleanliness ISO 15001:2011 Anesthetic and respiratory equipment. - Compatibility with oxygen

5

THE MAIN MEDICAL GASES

5INTRODUCTION


Symbol Name Application Source Type

O2 OxygenOxygen is one of the most extensively used gases for respiratory therapy and life-support and is additionally used in anesthetic procedures.

- Compressed gas cylinder - Liquid tank - Concentrator

Air AirMedical air is mainly used in respiratory therapy as a power source for patient ventilators, and for blending with oxygen. It is also used as the driving gas for nebulized drugs and chemotherapy agents.

- Compressor - Compressed gas cylinder

N2O Nitrous OxideNitrous oxide is used for anesthetic and analgesic purposes, being mixed with air, oxygen, and nebulized agents.

- Liquefied gas cylinder

CO2 Carbon DioxideCarbon dioxide is used less commonly now as a respiratory stimulant, and for insufflation during surgery.

- Liquefied gas cylinder

Air Surgical AirSurgical air (of medical air quality) is also used, at a higher pressure, to power a variety of surgical tools and other devices such as tourniquets.

- Compressor - Compressed gas cylinder

N2 NitrogenAs an alternative, nitrogen can be used for the same purpose as surgical air.

- Compressed gas cylinder

6


ALPINOX

ALPINOX MEDICAL OXYGEN P. 08

REGULATOR WITH FLOW SELECTORALPINOX MEDICAL OXYGEN P. 08

REGULATOR WITH QUICK CONNECTORALPINOX PIN INDEX MEDICAL P. 08

OXYGEN REGULATOR WITH FLOW SELECTOR

MINIOX

MINIOX QUICK CONNECTOR P. 10 MINIOX COLUMN FLOWMETER P. 10

PRESSURE REGULATORS | SPECIAL THERAPIES (ASSISTED)

BSC 280/380 P. 12

SINGLE STAGE CARTRIDGE REGULATORBSC 290/390 P. 14

SINGLE STAGE CARTRIDGE REGULATOR WITH HOSE BARB

DI 235 P. 16

NITRIC OXIDE APPLICATIONS DOUBLE STAGE BELLOW REGULATOR

PRESSURE REGULATORS | STANDARD RESPIRATORY THERAPIES

PRODUCT RANGE OVERVIEW

7


IN HOSPITAL THERAPY EQUIPMENT

FLOW METERING DEVICES

ALPI-FLOW FLOWMETER WITH CALIBRATED ORIFICES P. 18 COLUMN FLOWMETER P. 19

ACCESORIES

RESPIRATOTY THERAPY ACCESSORIES

REMOVABLE HOSE BARB P. 22 HUMIDIFIER P. 22 ALPI-CLICK P. 22

MEDICAL PROBES

MEDICAL CONNECTORS (SINGLE AND DOUBLE)

SUCTION EQUIPMENT

ALPI-VAC VACCUM REGULATOR P. 20 ALPI-VENT SUCTION UNITS P. 21

SUCTION ACCESSORIES

SMALL COLLECTION JAR P. 23 LARGE COLLECTION CONTAINERS P. 23 OUTLET HOSE CONNECTION P. 23

PRODUCT RANGE OVERVIEW

8


KEY FEATURES

- Single stage piston regulator ensuring high life cycle - Preset integrated pressure relief valve - Flowmeter with stop at 0 - Easy to clean - High precision fl ow from 0.25 lpm to 25 lpm - Continuous fl ow from 0 to maximal fl ow - Integrated safety relief device protected and none accessible

- Ergonomic handwheel and modern design. Red dot design award

- Easily cleanable - Rubber protection on the gauge - Plastic protection on the regulator

- Ergonomic plastic hand-wheel on the inlet connection - Position 25 lpm intended for the nebulization - 20μm Filter inside the seat regulator - Design free of fl uorinated polymers whose combustion products are toxic

- Individual number for traceability

OPTIONS

- Lateral marking

- Cylinder regulator for hospital and home care oxygen therapy

- A new generation of medical regulator with high fl ow precision and continuous fl ow between settings.

- In compliance with EN ISO 10524-1

ALPINOX MEDICAL OXYGEN REGULATOR

ALPINOX

STANDARD ALPINOX

ALPINOX WITH QUICK CONNECTOR

ALPINOX PIN INDEX

9


SPECIFICATIONS

Gas Medical oxygen, Air

Max Inlet pressure

200 bar

Gauge 0-315 bar, 0-4500 psi

Filter 20 micron, sintered bronze

Flow range From 0-2Lpm to 0-25Lpm

Body material white coated brass

O-ring material EPDM

Seat material Nylon

Regulatory status Complies with medical devices directive 93/42/EECand EN ISO 10524

CE marking CE0029

ALPINOX

PRODUCT CONFIGURATOR

Gas Working Pressure Cylinder Connection Outlet Pressure Flow Range Pressure outlet Flow outlet

M730 O2 200 NF 4.5 2L N HB6

O2 O2 200 bar 200 AFNOR NF 3.5 bar 3.5 0-2Lpm 2L None N Hose Barb Ø6mm - Fixed

HB6

Air AIR 2000 psi 2000 DIN D 4.5 bar 4.5 0-6Lpm 6L AFNOR NF Hose Barb Ø6mm - Removable 9/16”

9/16

N2O/O2 N2O 3000 psi 3000 BS B 0-15Lpm 15L DIN DIN 0-15Lpm M12

UNI U 0-25Lpm 25L BS BS 0-25Lpm 1/4

Pin-Index P SS SS

10


KEY FEATURES

Safety first - Smart choice of materials in conformance with ISO 15001 and the most restrictive additional requirements

- Design free of fluorinated polymers - Fitted with a safety relief valve in case of over pressure

- Even in case of failure, no high pressure exposure

High performances - Better outlet pressure and flow stability - Inverted seat regulator for a longer lifetime - Design resistant to pressure shocks & adiabatic compression

Lower operating costs - Compact and lightweight design for an easy handling and storage

- Suitable for all types of medical gases - Precise flow and improved stability for better gas consumption management

REGULATORY

- ISO 10524-1 - CGA E-7

MINIOX MEDICAL OXYGEN REGULATOR

- Medical pressure regulator for hospital and homecare respiratory therapy.

- Used to reduce cylinder pressure to a lower pressure suitable for medical equipment and/or for gas delivery direct to patient.

MINIOX

MINIOX WITH QUICK CONNECTOR MINIOX WITH COLUMN FLOWMETER

11


SPECIFICATIONS

Gas O2 / Air / N2O

Max. Inlet Pressure 200 bar

Gauge 0-315 bar

Temperaturerange

-20°C to +60°C

Body material Chrome plated brass

Diaphragm EPDM

O-rings EPDM

Seat PA 6.6

Filter 20 μm sinteredbronze

Outlet pressure 3.5 bar/4.5 bar

Max . Flow rate 40 Lpm

Weight 0,640 kg

Inlet Connection According to national standards

Outlet Connection According to national standards

PRODUCT DESCRIPTION

COLUMN FLOWMETER0-18 Lpm Outlet according to national standards (Available versions: single outlet & double outlet)

HIGH PRESSURE GAUGE 0-315 bar Cylinder content visual indication

INTEGRATED RELIEF VALVE Protect regulator against overpressure risks

CYLINDER VALVE CONNECTIONAccording to national standards

PRESSURE REGULATORDiaphragm technology

1

2

3

4

5

MINIOX

3

1 2

5

4

Gas Inlet pressure Outlet pressure Inlet connection Outlet dimensions Flow rate

M743 O2 200 4,5 DIN G1/4 15Oxygen O2 200 bar 200 4,5 bar 4,5 G¼ ” Female O2 G¼ ” G¼ 0-15 Lpm

Air AIR 2000 psi 2000 3,5 bar 3,5 NF 29-650 NF M12x125 M12 0-25 Lpm

DIN 477-1 DIN 9⁄16” UNF 9⁄16

BS 341-3 BS

NEN 3268 NEN

UNI 11144 UNI

CGA V1 CGA

Pin Index PI


Gas Inlet pressure Outlet pressure Outlet types Inlet connection Outlet dimensions

M743QC O2 200 4,5 SQC DIN DINOxygen O2 200 bar 200 4,5 bar 4,5 Single quick connector SQC G¼ ” Female O2 DIN 13260 DIN

3,5 bar 3,5 Dual quick connector DQC NF 29-650 NF AFNOR NF S90-116 AF

DIN 477-1 DIN SS8752430 SS

BS 341-3 BS

NEN 3268 NEN

UNI 11144 UNI

CGA V1 CGA

Pin Index PI

Flowmeter version

Quick connector version


12


Right inlet Left inlet

SERIES BSC 280/380 | SINGLE STAGE CARTRIDGE REGULATOR

INCLUDED FUNCTIONS

- Inlet port - Outlet port - Pressure regulator - Safety relief valve - High pressure measurement - Low pressure measurement

REGULATORY

- Medical certifi ed according to MDD 93/42/EEC amended 2007/47/EC

- Product complies with EN ISO 10524-1

- Enables gas supply to therapy machines

- Especially designed for accurate NO mixtures therapies

- Can be fi tted with pressure sensor for proper therapies parameters management

- 6 ports for multiple possible confi gurations and appropriate product integration thanks to compactness

SAFETY FIRST - Fitted with a safety relief valve in case of over pressure which can be collected

- Dedicated HP and LP pressure gauges for a permanent indication - Compatible materials with Oxygen and medical applications - No gas contamination due to a metal-metal sealing

HIGH PERFORMANCE - Proven Cartridge Seat Technology - Better outlet pressure and fl ow stability - Smart choice of material in conformance with EN ISO 15001

LOWER OPERATING COSTS - Compact and lightweight design for an easy handling and storage - Longer product life thanks to less impingement on the diaphragm - Easy maintenance operations thanks to Cartridge Technology

KEY ADVANTAGES

Pressure gauges

Outlet (LP)

Safety valve

Inlet (HP)

Plugged Plugged

HIGH PRESSURE REGULATOR


13

SPECIFICATIONS


Body Chrome plated brass

Seat seal Polyamide

O-ring EPDM

Diaphragm Hastelloy®

Inlet Connection Cylinder connection

Outlet Connection Hose Barb or Medical connector

Leak rate 10-8 mbar l/s He

Weight ± 1.4 kg

Inlet pressure 200 / 300 bar2900 / 4350 psi

Outlet pressure 4 / 8 bar58 / 116 psi

Nominal Flow 7 / 25 Nm3/h (N2)

Temperature range

-40°C to +60°C


Material Inlet Pressure Port Configuration Outlet pressure Inlet Connection Outlet connection Pressure Sensor Gas

BSC I 280 R 5 DIN NIST B NO

Stainless steel

I 200 bar 280 Right inlet R 5 bar 5 DIN477-1 DIN G¼” F G14F without pressure sensor

A NO (max 1000ppm)/N2

NO

Left inlet L ISO5145 ISO ¼”NPT F N14F with HP pressure sensors

B

CGA V1 CGA with LP pressure sensor

C

with HP & LP pressure sensors

D



14


Right inlet Left inlet

SERIES BSC 290/390 | HP CYLINDER PRESSURE REGULATOR

INCLUDED FUNCTIONS

- Inlet port - Outlet port - Pressure regulator - Safety relief valve - High pressure measurement - Low pressure measurement

REGULATORY

- Medical certified according to MDD 93/42/EEC amended 2007/47/EC

- Product complies with EN ISO 10524-1

- Enables gas supply to therapy machines

- Can be fitted with pressure sensor for proper therapies parameters management

- 6 ports bodies for multiple possible configurations and appropriate product integration

SAFETY FIRST - Fitted with a safety relief valve in case of over pressure which can be collected

- Dedicated HP and LP pressure gauges for a permanent indication - Compatible materials with Oxygen and medical applications - No gas contamination due to a metal-metal sealing

HIGH PERFORMANCE - Proven Cartridge Seat Technology - Better outlet pressure and flow stability - Smart choice of material in conformance with EN ISO 15001

LOWER OPERATING COSTS - Compact and lightweight design for an easy handling and storage - Longer product life thanks to less impingement on the diaphragm - Easy maintenance operations thanks to Cartridge Technology

KEY ADVANTAGES

Pressure gauges

Outlet (LP)

Safety valve

Inlet (HP)

Plugged Plugged



15

SPECIFICATIONS


Body Chrome plated brass

Seat seal Polyamide

O-ring EPDM

Diaphragm Hastelloy®

Inlet Connection Cylinder connection

Outlet Connection Hose barb or medical connector

Leak rate 10-8 mbar l/s He

Weight ± 1.4 kg

Inlet pressure 200 / 300 bar2900 / 4350 psi

Outlet pressure 4 / 8 bar58 / 116 psi

Nominal Flow 7 / 25 Nm3/h (N2)

Temperature range

-40°C to +60°C


Material Inlet Pressure Port Configuration Outlet pressure Inlet Connection Outlet connection Pressure sensor Gas Type

BSC L 290 R 4 NF NIST B O2

Chrome plated brass

L 200 bar 2900 psi

290 Right inlet R 4 bar 58 psi

4 G¼” Female O2 Hose Barb 6 mm

HB without pressure sensor

A O2 O2

300 bar 4350 psi

390 Left inlet L 8 bar 116 psi

8 NF 29-650 NF AFNOR Medical Connector

NF with HP pressure sensors

B Air AIR

10 bar 145 psi

10 DIN 477-1 DIN DIN Medical Connector

DIN with LP pressure sensor

C N2O N2O

BS 341-3 BS NIST Medical Connector

NIST with HP & LP pressure sensors

D CO2 CO2

NEN 3268 NEN N2 N2

UNI 11144 UNI

CGA V1 CGA



16 PRESSURE REGULATORS | SPECIAL THERAPIES (ASSISTED)

APPLICATIONS

- Designed for cylinder regulator applications. - Ideally suited for special NO/N2 mixtures (N2 with 1000 ppm NO) applications requiring a very stable outlet pressure together with a very sensitive set up of this outlet pressure.

KEY FEATURES

- The DI 235 regulator is based on the S 20 proven bellow technology.

- Accurate pressure control for reliable service and guarantees a stable outlet pressure due to the combination of the diaphragm and bellow technology.

- Compact and lightweight design. - Can also be equipped with a needle or shut off valve at the outlet.

Compact and lightweight design

1 inlet / 2 outlets Inlet/outlet pressure gauges 2 safety relief valves

Special requirements on request

- For NO/N2 mixtures - Diaphragm/bellow dual stage

- Purity up to 6.0 - Max inlet pressure: 300 bar (4350 psi)

- Preset outlet pressure: 2,5/5 bar (36/72 psi)

SERIES DI 235 | NITRIC OXIDE DOUBLE STAGE BELLOW REGULATOR


0

14,5

29

43,5

58

72,5

87

101,5

116

0,0

1,0

2,0

3,0

4,0

5,0

6,0

17

SPECIFICATIONS

PRESSURE REGULATORS | SPECIAL THERAPIES (ASSISTED)

PRODUCT CONFIGURATIONS

Body Material Outlet Pressure End Connections Gauges

D I 235 5 G 1

Stainless steel I 2,5 bar36 psi

2,5 In: 16 x 1.336 Out: G 3⁄8

G Without 0

5 bar72 psi

5 ¼ NPT - ¼ NPT N With 1

Female ports 16 x 1.336 (inlet) - G 3⁄8 (outlet)or ¼ NPT (inlet/outlet)

Seat seal PTFE (1st stage) EPDM (2nd stage)

O-ring FPM

Diaphragm Hastelloy

Bellow AISI 316L (SS version)

Weight ± 1,4 kg± 3.0 lbs

Leak rate 10-8 mbar ℓ/s He

Temperature range - 20°C to + 60°C- 4°F to + 140°F

Gauges High and low pressure (M10 x 1 or ¼ NPT)

Max inlet pressure 300 bar4350 psi

Outlet pressure 2,5/5 bar 36/72 psi

Nominal Flow 1,8/3 Nm3/h (N2)

FLOW CURVES

OU

TLET

PR

ESSU

RE-

bar

an

d p

si

PRESSUREbar

PRESSUREpsi

Blue line P1 = 300 barRed line P1 = 150 barGreen line P1 = 75 bar

FLOW CURVE DI 235 REGULATORSET: 5 bar / 72.5 psi

2.5 bar / 36.25 psi

Nm3/h 1 2 3 4 5 6

Nlpm 17 33 50 66 83 100

Slpm 18 35 53 70 88 105

SCFM 0.6 1.2 1.9 2.5 3.1 3.7

FLOW RATE in Nitrogen (N2)

360°

TO BE MOUNTED ON A

RAIL WITH FLEX HOSE

(ACC. TO EN ISO 5359)

18


M730 | ALPI-FLOW FLOWMETER WITH CALIBRATED ORIFICES

KEY FEATURES

- Continuous fl ow between settings - Stop at 0 - Inlet pressure : 4 bar 0/+1 bar - Flow precision acc. EN ISO 15002 - Flow range: 0-15 lpm (12 positions)

NEW GENERATION ALPINOX FLOWMETER

MEDICAL FLOWMETER

- High fl ow precision from 0.1 lpm to 25 lpm - Continuous fl ow from 0 to maximal fl ow - Ergonomic and modern design - Easily cleanable - Plastic protection on the fl owmeter - Position 25 lpm intended for the nebulization - Swiveling design 360° for optimal readability - Design free of fl uorinated polymers whose combustion products are toxic

- Flow-meter for hospital and ambulance oxygen therapy

- New generation of medical fl ow-meter with high fl ow precision and continuous fl ow between settings. The fl ow-meter is in compliance with the EN ISO 15002

TO BE CONNECTED ON CEODEUX MEDITEC TERMINAL UNITS

IN-HOSPITAL THERAPY EQUIPMENT

SPECIFICATIONS

Inlet Connection Medical connector acc. to national standards

Flow Outlet M12x1.25 M.-9⁄16”UNF M. -G¼ ” M.

Dimensions 136x33x82mm

Weight 0.230 Kg

Inlet pressure 6 bar max

Temperature range

-20°C to +60°C

Flow Range 0-15 Lpm

Accuracy ± 10 % read value or ± 0.5 Lpm if greater

Body Chrome plated

O-ring EPDM

Measuring tube Polycarbonate


Gas Inlet Pressure Flow range Inlet Connection Flow outlet

M730-FM O2 3.5 2L NF 9/16

O2 O2 3.5 bar 3.5 0-2Lpm 2L AFNOR NF Hose Barb Ø6mm - Removable 9⁄16”

9/16

Air AIR 4.5 bar 4.5 0-6Lpm 6L DIN DIN Hose Barb Ø6mm - Removable

NF

N2O N2O 0-15Lpm 15L BS BS M12x125 M12

0-25Lpm 25L SS SS Hose Barb Ø6mm - Removable G¼ ”

1/4

TO BE MOUNTED ON A

RAIL WITH FLEX HOSE

(ACC. TO EN ISO 5359)

TO BE CONNECTED ON CEODEUX MEDITEC TERMINAL UNITS

19


IN-HOSPITAL THERAPY EQUIPMENT

KEY FEATURES

- Swiveling design 360° for an optimal orientation - Gas specifi c marking and color - Available in twin units versions for two independent suppliers from one single source.

REGULATORY

- Medical CE certifi ed according to MDD 93/42/EEC amended 2007/47/EC

- Product complies with EN ISO 15002

ALPINOX COLUMN FLOWMETER

- Medical Column Flowmeter for Oxygen and others medical gases (Air, N2, CO2, N2O)

- Combination of a precise needle valve and an accurate measuring device for a proper dosage of medical gases

SPECIFICATIONS

Inlet Connection Medical connector acc. to national standards

Flow Outlet M12x1.25 M.-9⁄16”UNF M. -G¼ ” M.

Dimensions 136x33x82mm

Weight 0.230 Kg

Inlet pressure 6 bar max

Temperature range

-20°C to +60°C

Flow Range 0-15 Lpm

Accuracy ± 10 % read value or ± 0.5 Lpm if greater

Body Chrome plated

O-ring EPDM

Measuring tube Polycarbonate

Removable Hose barb

M12x1.25 F. -9⁄16”UNF F.-G¼ ” F.

Humidifi ers M12x1.25 F. -9⁄16”UNF F.-G¼ ” F.200mL / 300mL / 500mL

OPTIONS


Gas Inlet Pressure Flow range Inlet Connection Flow outlet

CFM O2 3.5 15L NF 9/16

O2 O2 3.5 bar 3.5 0-15Lpm 15L AFNOR NF Hose Barb Ø6mm - Removable 9⁄16”

9/16

Air AIR 4.5 bar 4.5 DIN DIN Hose Barb Ø6mm - Removable

NF

BS BS M12x125 M12

SS SS Hose Barb Ø6mm - Removable G¼ ”

1/4


- Medical vaccum regulator (VAC)

- Regulator suitable for all medical suction applications in hospitals and nursing homes

- Insure safe, quick and reliable use thanks to performant technology and easy manipulation

ALPI-VAC | VACCUM REGULATOR

SPECIFICATIONS

Sizes (LxWxH) 103x92x170 mm

Weight ALPI-VAC 250: 0.42 Kg ALPI-VAC 600/1000: 0.37 Kg

Maximum suction rate

ALPI-VAC 250: 50 L/min. ±5 L/min. at -220 mbar ALPI-VAC 600: 72 L/min. ±5 L/min. at -550 mbar ALPI-VAC 1000: 115 L/min. ±5 L/min. at -950 mbar

Maximum adjustable depression

ALPI-VAC 250: -220 mbar ±20 mbarALPI-VAC 600: -550 mbar ±20 mbarALPI-VAC 1000: -950 mbar

Valve protecting against excessive

negative pressures

ALPI-VAC 250/600: preset with anti-clogging system ALPI-VAC 1000: N/A

Maximum supply depression

-950 mbar

Suction adjusting system

With membrane

Standard vacuum supply connection

ISO G. ¼” M

Outlet connection ISO G. ½” M

I/0 switch Quick push button type

SUNCTION EQUIPMENT20

KEY FEATURES

The ALPI-VAC continuous suction vacuum regulator is particularly suitable for all medical suction applications in hospitals and nursing homes.

The device is made of a strong techno-polymer body, with a quick I/0 switch-button, a suction adjustment knob and a control vacuum gauge with three possible end-of-scale choices: -250 mbar, -600 mbar and -1000 mbar. A protective silicone cover prevents gauge damages caused by possible shocks received during transport or use.

The ALPI-VAC vacuum regulators are also designed, through a threaded connection, for connecting directly or indirectly to the normal collection containers for suctioned fluids.

The extreme rationality and simplicity, combined with the sophisticated technical execution, allow both operators and patients to appreciate the safety and reliability of this medical device.


21SUNCTION EQUIPMENT

ALPI-VENT | SUCTION UNITS

KEY FEATURES

The ALPI-VENT/500 and ALPI-VENT/1000 vacuum generating system units are particularly suitable in all hospital applications in which it is necessary to get values of vacuum up to -850 mbar and where a central facility of vacuum generation for suction is missing, often for technical choice.

As it is well known, the physical principle called “Venturi” allows to get depression from a fluid under pressure, which is obtained, in case of these devices, using medical compressed air coming from the centralized distribution plant.

Such devices are composed essentially of a brass chrome-plated body, a needle valve with vacuum adjustment knob and a vacuum gauge. The version ALPI-VENT/1000 fits also a quick I/0 button switch and a large gauge, while in the version ALPI-VENT/500 a protective silicone cover on vacuum gauge avoids damages caused by possible impacts during transport or use.

- Vaccum generating system unit (VAC)

- Up to 850 mbar - Suitable for all hospital applications where a central facility of vacuum generation for suction is missing

SPECIFICATIONS

Sizes (without collection jar)

(LxWxH)

ALPI-VENT/500: 88x70x92 mm ALPI-VENT/1000: 140x80x140 mm

Weight (without collection jar)

ALPI-VENT/500: 0.80 Kg ALPI-VENT/1000: 0.95 Kg

Max. suction range

ALPI-VENT/500: 25 L/min. ±2 L/min. ALPI-VENT/1000: 27 L/min. ±2 L/min.

Vacuum gauge scale

ALPI-VENT/500: 0 ÷ -1000 mbar ALPI-VENT/1000: 0 ÷ -1 bar

Suction range ALPI-VENT/500: -800 mbar ±25 mbar ALPI-VENT/1000: -850 mbar ±25 mbar

Standard supply pressure

2.7 ÷ 5.5 bar

Adjustment of suction level

needle valve

Air consumption at the max.

suction value

47 L/min. ±2 L/min.

Inlet connection ISO G. ¼” M.

Outlet connection

to the patient

ISO G. ½” M.

ALPI-VENT/500

ALPI-VENT/1000

22


ADVANTAGES

- Swiveling design 360° for optimal use. - Design free of fl uorinated polymers whose combustion products are toxic.

- Used to connect or disconnect two specifi c medical devices for anesthesia, ventilation, oxygen therapy or various medical therapies.

- Designed and approved in accordance with the following standards: NF S 90-116 , DIN 13260-2 , SS 8752430 , EN737-6 .

22

RESPIRATORY THERAPY ACCESSORIES

REMOVABLE HOSE BARB

HUMIDIFIER

ALPI-CLICK MEDICAL PROBES MEDICAL CONNECTORS (SINGLE AND DOUBLE)

ACCESORIES

- Devices used to connect or disconnect specifi c medical devices for anesthesia, ventilation, oxygen therapy or various medical therapies.

- Designed according to EN 13544-2 for ø 6mm tube.

SPECIFICATIONS

SPECIFICATIONS

SPECIFICATIONS

Gas Oxygen, Air, 50% N20 / 50% 02 Materials Brass chrome plated, EPDM, Nylon CE marking CE 0029

Inner volume CH/200: 210 mlTR/200: 120 mlMAK/300: 285 mlMAK/500: 355 ml

Sizes (LxWxH) CH/200: 55x67x200 mmTR/200: 60x75x190 mmMAK/300: 70x81x175 mmMAK/500: 70x81x207 mm

Weight CH/200: 0.11 KgTR/200: 0.13 KgMAK/300: 0.15 KgMAK/500: 0.16 Kg

Applicable pressure and fl ow

Pressure: 500 kPaFlow: 10 L/min.

Inlet connection ¼ ” ISO 3253 F3⁄8” ISO 3253 FM 12x1.25 F9⁄16” UNF F

Outlet connection Hose connector Ø 6÷9 mm

Thread M12x125G¼ ”9⁄16” UNF

Materials Brass chrome plated CE marking CE 0029

- Used to connect or disconnect specifi c medical devices for anesthesia, ventilation, oxygen therapy or various medical therapies.

- Designed and approved in accordance with the EN ISO 9170-1


23ACCESORIES

SUCTION ACCESSORIES

ADVANTAGES

- Connector for hose Ø 7.5 mm, ISO G. 1/2” F. inlet thread.

- Vacuum regulator outlet hose connection

- Use to connect ALPI-VAC (Vaccum regulator) and its equipment MAK (collection container)

SMALL COLLECTION JAR

LARGE COLLECTION CONTAINERS

OUTLET HOSE CONNECTION

ADVANTAGES

- The two models have capacities of 300 ml and 500 ml respectively in standard execution, or fi tting a special lid for housing an antibacterial fi lter.

- The jar and the lid are made in polycarbonate, with fi ttings in brass, with ergonomic screw nut in high-strength polycarbonate. All parts can be sterilized in an autoclave (121 °C - 15 min.)

- Small collection jar are used for suction of small volume of fl uids and have been designed and manufactured for applications of “high fl ow and high vacuum”

- Can also be use as a safety container to protect the equipment and the plant upstream of the section source

- Matched with ALPI-VAC vacuum regulators

ADVANTAGES

- These devices are available with a capacity of 1000 ml with screw cap, of 2000 ml with screw and pressure lid and 4000 ml with pressure lid.

- The jar and the lid are made in polycarbonate, with fi ttings in brass, with ergonomic screw nut in high-strength polycarbonate. All parts can be sterilized in an autoclave (121 °C - 15 min.).

- Large collection container for suctioned liquid for applications of “high fl ow” and “high vaccum”

- Can also be use as a safety container to protect the equipment and the plant upstream of the section source

- Matched with ALPI-VAC vacuum regulators

Inner volume MAK/300/300 a.b: 300 mlMAK/500/500 a.b: 500 ml

Sizes (LxWxH) MAK/300: 70x98x180 mmMAK/300 a.b: 70x98x210 mmMAK/500: 70x98x215 mmMAK/500 a.b: 70x98x245 mm

Weight MAK/300: 0.20 KgMAK/300 a.b: 0.24 KgMAK/500: 0.21 KgMAK/500 a.b: 0.25 Kg

Supply depression max -950 mbar - 5 min

Overfl ow valve Floating valve

Inlet connection ISO G ½ ” F.

Outlet connection Hose connector Ø 8.0 ÷ 9.2 mm

Inner volume MAK/1000: 1000 mlMAK/2000 with screw lid: 2000 mlMAK/2000 with pressure lid: 2000 mlMAK/4000: 4000 ml

Sizes (LxWxH) MAK/1000: 110x110x243 mmMAK/2000 with screw lid/ with pressure lid: 140x140x298 mmMAK/4000: 175x175x310 mm

Weight MAK/1000: 0.38 KgMAK/2000 with screw lid: 0.49 KgMAK/2000 with pressure lid: 0.49 KgMAK/4000: 0.99 Kg

Supply depr. max -950 mbar- 5 min

Overfl ow valve Floating valve

Inlet connection Hose connector Ø 8.0÷9.2 mm or ISO G 1/2” F (for MAK/1000 and MAK/2000 screw lid only)

Outlet connection Hose connector Ø 8.0÷9.2 mm

Antibacteria system also available for both model (see specifi cation table: a.b)

NOTES

24


NOTES

25


A FULL LINE OF GAS CONTROL SOLUTIONS

ROTAREX is helping engineers worldwide to get better gas results: from ultra high purity production and medical care facilities to industrial and LPG applications, as well as alternative energy vehicles, fire suppression, diving, aerospace, cryogenics, laboratory, petro-chemical and welding. ROTAREX applies over 90 years of know-how and experience to custom design, develop and manufacture the high performance valves, regulators and fittings to suit your needs, all in one hand. Discover the difference ROTAREX can make in your world.

COMPLETE SOLUTIONS FROM SOURCE TO PROCESS.

MEDITECCYLINDER VALVES EQUIPMENT FIRETEC AUTOMOTIVE LPG/SRG

AUSTRALIA ⁄ BRASIL ⁄ CHINA ⁄ FRANCE ⁄ INDIA ⁄ ITALY ⁄ JAPAN ⁄ LUXEMBOURG ⁄ MIDDLE EAST ⁄ RUSSIA ⁄ SINGAPORE ⁄ SPAIN ⁄ THAILAND ⁄ USA

ULTRA HIGH PURITY VALVES MEDICAL VALVES & EQUIPMENT INDUSTRIAL CYLINDER VALVES REFRIGERANT CYLINDER VALVES

PRESSURE REGULATORS SUPPLY & SWITCH OVER BOARDS LINE VALVES FITTINGS & ADAPTORS

FIXED INSTALLATION FIRE SYSTEMS

OBJECT FIRE SUPPRESSION SYSTEMS

AUTOMOTIVE VALVES & REGULATORS WATER CARBONATION

LPG TANK VALVES & REGULATORS

LPG CYLINDER VALVES & REGULATORS

DIGITAL MEASUREMENT SYSTEMS PLASTIC INJECTION MOULDING

www.rotarex.comwww.rotarex.comwww.rotarex.com

WORLDWIDE HEADQUARTERS

Ceodeux Meditec Customer Service

24 rue de Diekirch, B.P. 19

7505 Lintgen, Luxembourg

Tel.: +352 32 78 32 1

Fax: +352 32 78 32 854

E-mail: [email protected]

© 2012 - ROTAREX S.A.

CEODEUX MEDITEC - CEODEUX S.A.

MPR-EN-1115

REGIONAL / COUNTRY HEAD QUARTERS

NORTH AMERICA

USARotarex North America

221 Westec Drive

Westmoreland Technology Park I

Mt. Pleasant, Pennsylvania 15666 USA

Tel.: +1 724-696-43 40

Fax: +1 724-696-43 64


SOUTH AMERICA

BRASILRotarex Brazil Ltda

Cond. Ind. Portal da Anhanguera Estr. Municipal

Gov. Mário Covas, S/N

13279-411 Bairro Macuco -Valinhos

São Paulo Brazil

Tel.: +55 19 3518 0800

Fax: +55 19 3869-1503


EUROPE

FRANCE, BENELUX, GERMANY24, rue de Diekirch, BP 19

L-7505 Lintgen, Luxembourg

Tel.: +352 32 78 32-1

Fax: +352 32 78 32 317


ITALYRotarex Italia S.r.l.

46 Via Giacomo Matteotti

I-25080, Ciliverghe di Mazzano (BS) Italy

Tel.: +39 030 212 05 50

Fax: +39 030 212 23 62


SPAINRotarex Spain

C/Alcala, 4° Oficina 404

28014 Madrid

Tel.: +34 (91) 570 89 05

Mobile: + 34 (650) 908 856


RUSSIARotarex Rus

Tverskaya street, 20/1 bldg. 1 of 506

125009, Moscow Russia

Tel.: +7 985 125 7776

Skype: rotarexrus


POLANDRotarex Polska

13 Gröbli

PL 49-300 Brzeg, Poland

Tel.: +48 77 416 40 16

Fax: +48 77 416 20 99


ASIA

MIDDLE EASTRotarex Middle East

Jebel Ali Free Zone - Lob 17, Office 415

P.O. Box 261749

Dubai, U.A.E.

Tel.: +971 (0) 4 887 6701

Fax: +971 (0) 4 887 6702


CHINARotarex Star

60 Yuan Zhong Road

Shanghai Nanhui Industrial Zone

201300, Shanghai China

Tel.: +86-21 5800 4000

Fax: +86-21 5800 3226


SINGAPORERotarex Fareast Pte Ltd

10 Ubi Crescent

Ubi Techpark, Lobby C, #06-55

408564 Singapore

Tel.: +65 64 72 37 27

Fax: +65 64 72 45 28


JAPANRotarex Japan Ltd

6F, Yawaragi Bldg., 1-27-11 Taito

Taito-ku, Tokyo

110-0016 JAPAN

Tel.: +81 3 5817 8108

Mob.: +81 80 3755 2539

Fax: +81 3 5817 8168


INDIARotarex ENGG. PVT. LTD.

C-105, Mahindra Apartments

Vikaspuri, New Delhi 110018

mob.: +91-9873467666


THAILANDRotarex (Thailand) Co Ltd.

297, Wanglee Tower

3rd floor, Unit C, Surawong Road

Suriyawong, Bangrak,

Bangkok 10500 Thailand

Tel.: +66 2635 71 79


SOUTH KOREARotarex Luz Tech Co.

305-500, 547 Yongsan-dong

Yuseong-gu

Taejon, Korea

Tel.: +82 42 825 8911

Fax: +82 42 825 8913


OCEANIA

AUSTRALIARotarex Australia/New Zealand

Hornsby Heights,

Sydney, NSW, 2077

Tel.: +61 477 477 481


PRESSURE REGULATORS, FLOW METERS, -...

Documents

Transcript of PRESSURE REGULATORS, FLOW METERS, -...