Prerequisite: Set the NTP Server · SightLogix, Inc. | +1 609.951.0008 | 02192016 r1 Configuring...
7
SightLogix, Inc. | +1 609.951.0008 | www.sightlogix.com 02192016 r1 Configuring EXACQ Prerequisite: Set the NTP Server Before adding a Sightlogix device to Exacq, the NTP server and the time zone need to be set up correctly using the SightLogix CS. See Figure 1 and 2 below. Figure 1: Configure NTP server Figure 2: Configure Time Zone
Transcript of Prerequisite: Set the NTP Server · SightLogix, Inc. | +1 609.951.0008 | 02192016 r1 Configuring...
SightLogix, Inc. | +1 609.951.0008 | www.sightlogix.com 02192016 r1
Configuring EXACQ
Prerequisite: Set the NTP Server
Before adding a Sightlogix device to Exacq, the NTP server and the time zone need to be set up correctly using the SightLogix CS. See Figure 1 and 2 below.
Figure 1: Configure NTP server
Figure 2: Configure Time Zone
Configuring Exacq
SightLogix, Inc. | +1 609.951.0008 | www.sightlogix.com
Using Exacq in Onvif – H.264 mode with Motion Alarm Events
1. In the SightLogix SightMonitor, configure the SightLogix Camera with VMS Type “ONVIF H264”.
2. Add Motion On Event Server URLs with the IP address of tbe Exacq server and a unique port number for each SightLogix camera.
Configuring Exacq
SightLogix, Inc. | +1 609.951.0008 | www.sightlogix.com
Next, in Exacq, do the following:
1. Add the SightLogix camera to Exacq as ONVIF type User “service”, password “test1234”. 2. Change the video channel name using the SightLogix device’s Serial Number.
Configuring Exacq
SightLogix, Inc. | +1 609.951.0008 | www.sightlogix.com
Named Video Source
Configuring Exacq
SightLogix, Inc. | +1 609.951.0008 | www.sightlogix.com
Creating and IP Serial Port to Receive SightLogix Events
Create IP Serial Ports for each SightLogix camera, using the camera serial number in the name, as shown.
Also, create Serial Profiles for the Motion On Event.
Do the same for the Motion Off event, if required.
Configuring Exacq
SightLogix, Inc. | +1 609.951.0008 | www.sightlogix.com
Linking SightLogix Events to Video Recording
Associate events in the Serial Profile with a Recording action if you wish to see marks in the recorded video for motion alarms.
1. Click New to create a new Server Action 2. Select your Serial Profile and Record Video 3. Match the Event Source and Video for the appropriate SightLogix device serial number
Named Video
Source
Configuring Exacq
SightLogix, Inc. | +1 609.951.0008 | www.sightlogix.com
Finally, an example showing a search for events in the recorded video is provided below.
Note that the SightLogix Motion On event is indicated by the red highlighting in the timeline.
Copyright © SightLogix. All rights reserved.
SightLogix, SightSensors, and SightTrackers are trademarks of SightLogix, Inc.
All other trademarks are the property of their respective owners.
SightLogix is a licensee of the GNU General Public License (GPL). You can request a copy of the GPL-licensed source code used in this product from a SightLogix sales office.
No part of this document may be reproduced or transmitted in any form or by any means, electronic or mechanical, for any purpose, without the express written permission of SightLogix.
The information in this document is distributed on an “As is” basis and without warranty. While every precaution has been taken in the preparation of this document, SightLogix assumes no responsibility for errors or omissions or for any damages resulting from the use of the information contained herein.
