Premium SSE Pumps - resiflowlit.com · 3 DC233/DC250 KEY FEATURES n 1/3 or 1/2 HP n Rugged cast...
Transcript of Premium SSE Pumps - resiflowlit.com · 3 DC233/DC250 KEY FEATURES n 1/3 or 1/2 HP n Rugged cast...
Premium SSE Pumps
Sump
Sewage
Effluent
An AdvantageYou Can Count On™
Many Solutions.One Source.
SC7 Series Sewage Pumps
SC6 Series Sewage Pumps
SG11 2 HPGrinder Series
ST.E.P. Plus® D Series
DB200 Battery Back-Up
1
TABLE OF CONTENTS
Please refer to the SSE price list for complete ordering information.
SUMP PUMPS
P1/PC1 2
D125/D133/D150 2
DC233/DC250 3
D175 3
DRAINER PRE-PLUMBED SYSTEM
DP233 4
BATTERY BACK-UP
DB100 5
DB200 5
EFFLUENT PUMPS
EC2 6
EC3 6
EC4 7
EC6/EC7/EH7 8
EC9 9
SPECIALTY PUMPS
HT3/HTX3 7
HT7 9
HIGH HEAD EFFLUENT PUMPS
ST.E.P. Plus® 10
ST.E.P. Plus® D Series 11
SEWAGE PUMPS
SC4 12
SC5 12
SC6 13
SC7/SCC7 14
SC9/SCC9 15
SEWAGE PRE-PLUMBED SYSTEMS
SP4 16
SP5 16
GRINDER PUMPS
SG11 17
COMPOSITE CURVES
Effluent/Specialty Pumps 18
Sewage Pumps 19
Grinder Pumps 20
GENERAL INFORMATION
Product Nomenclature 21
SUMP PUMPS
D125/D133/D150
KEY FEATURESn 1/4, 1/3, or 1/2 HPn High-impact corrosion-resistant engineered resin constructionn 1-1/4" (32mm) FNPT or 1-1/2" (38mm) MNPT dischargen Piggy-back style float for automatic or manual operationn Oil-filled motor for continuous lubrication n Easily replaceable 8’ (2.4 M) power cord with optional lengths available n Automatic reset overload provides safe operation
SPECIFICATIONSApplications: Basement Sumps, DewateringCapacities: To 54 GPM (204 LPM)Heads: To 24 FT (7.3 M)Cont. Liquid Temp: 77°F (25°C)Motor: 1/4 HP = 8.5FLA; 1/3 HP = 9.0FLA; 1/2 HP = 13.0FLA (all 3450 RPM); Shaded pole with thermal overload protectionElectrical: 115 Volt, 1Ph, 60HzOperation: Tethered models, on/off: 14”/6” (356mm/152mm); or
Vertical models, on/off: 8”/31/2” (203mm/89mm) Min. Basin Diameter: 14" (356mm) tethered; 10” (254mm) verticalImpeller: Thermoplastic, open vane typeSolids Handling: 1/8" (3.2mm)Power Cord: 8’ (2.4 M) type SJTW-A/SJT
MODEL NUMBER
D12518T
D15018T
D12518V
D13318V
D15018V
S E R I E S
2CAPACITY GALLONS PER MINUTE
CAPACITY LITRES PER MINUTE
TOTA
L H
EAD
IN M
ETER
S
TOTA
L H
EAD
IN F
EET
25
20
15
10
5
0 30 60
200 250
15 45 75
150100500
7
6
5
4
3
2
1
0
D125 – 1/4 HP
D133 – 1/3 HP
D150 – 1/2 HP
VerticalTethered
P1/PC1
KEY FEATURESn 1/3 HPn P1: Thermoplastic base and support column PC1: lass 30 cast iron base, stainless steel columnn P1: 1-1/4” (32mm) NPT discharge PC1: 1-1/2” (38mm) NPT dischargen Vertical-style switch provides easy adjustment for on/off setting to specific application needsn Air-cooled motor with automatic reset overload provides safe operation
SPECIFICATIONS
Applications: Basement Sumps, DewateringCapacities: To 50 GPM (189 LPM)Heads: To 22 FT (6.9 M)Cont. Liquid Temp: 77°F (25°C)Motor: 1/3 HP (1725 RPM) PSC with thermal overload, air cooledElectrical: 115 Volt, 3.5FLA, 1Ph, 60HzOperation: Vertical Min. Basin Diameter: 14" (356mm) tethered; 10" (254mm) verticalImpeller: Thermoplastic, open vane typeSolids Handling: 3/8" (9.5mm)Power Cord: 6'(1.8M)
MODEL NUMBER
P13316V
PC13316V
S E R I E S
CAPACITY GALLONS PER MINUTE
CAPACITY LITRES PER MINUTE
TOTA
L H
EAD
IN M
ETER
S
TOTA
L H
EAD
IN F
EET
25
20
15
10
5
0 20 40
125 175
10 30 50
1007550250 150
7
6
5
4
3
2
1
0
P133/PC133 – 1/3 HP
PC1P1
S4300SSE S5611SES
3
DC233/DC250
KEY FEATURESn 1/3 or 1/2 HPn Rugged cast iron pump body and motor cover, exterior hardware stainless steel constructionn 1-1/2" (38mm) NPT discharge n Carbon/Ceramic mechanical seal nPiggy-back style float for automatic operationn Oil-filled motor with automatic reset overload provides safe operation n Ball bearing construction for long lifenEasily replaceable power cord with optional lengths available
SPECIFICATIONSApplications: Basement Sumps, Dewatering, Light Effluent, Water TransferCapacities: To 62 GPM (234 LPM)Heads: To 32 FT (9.75 M)Cont. Liquid Temp: 130°F (55°C)Motor: 1/3 HP = 9.8FLA; 1/2HP = 12.0FLA (both 1550 RPM); Shaded pole with thermal overload protectionElectrical: 115 Volt, 1Ph, 60HzOperation: Tethered models, on/off: 121/2"/31/2" (318mm/89mm); Vertical models, on/off: 61/2"/2" (165mm/51mm)Min. Basin Diameter: 14" (356mm) tethered; 10" (254mm) verticalImpeller: Thermoplastic, vortex typeSolids Handling: 1/2" (12.7mm)Power Cord: 10’ (3 M) or 20' (6 M) 16-3, SJTW-A/SJTW
MODEL NUMBER
DC233110T
DC233120T
DC233130T
DC233110V
DC233120V
DC233120M
DC250110T
DC250120T
DC250110V
DC250120V
DC250110M
S E R I E S
CAPACITY GALLONS PER MINUTE
CAPACITY LITRES PER MINUTE
TOTA
L H
EAD
IN M
ETER
S
TOTA
L H
EAD
IN F
EET
40
30
20
10
0 20 8040 60
200150100500 250
10
8
6
4
2
0
DC233 – 1/3 HP
DC250 – 1/2 HP
TetheredVertical
S5099SES
SUMP PUMPS
KEY FEATURESn 3/4 HP n Energy efficient PSC motor n Includes check valve and universal adapter for 1-1/4” (32mm) or 1-1/2" (38mm) pipen High-impact resin and stainless steel constructionn Piggy-back style float for automatic or manual operation n Oil-filled motor with automatic reset overload provides safe operation nBall bearing construction for long lifen Easily replaceable power cord with optional lengths available
SPECIFICATIONSApplications: Basement Sumps, Dewatering, UtilityCapacities: To 100 GPM (378 LPM)Heads: To 25 FT (7.6 M)Cont. Liquid Temp: 77°F (25°C)Motor: 3/4 HP (3450 RPM); PSC with thermal overloadElectrical: 115 Volt, 7.5FLA, 1Ph, 60HzOperation: Tethered models, on/off: 121/2”/ 31/2” (318mm/89mm); or Manual modelsMin. Basin Diameter: 14" (356mm) tethered; 10" (254mm) manualImpeller: Thermoplastic, closed vane typeSolids Handling: 1/8" (3.2mm)Power Cord: 10' (3 M) or 20’ (6 M) 16-3, SJTW-A/SJTW
MODEL NUMBER
D175110T
D175120T
D175120M
S E R I E SD175
CAPACITY GALLONS PER MINUTE
CAPACITY LITRES PER MINUTE
TOTA
L H
EAD
IN M
ETER
S
TOTA
L H
EAD
IN F
EET
25
20
15
10
5
0 40
300
20 60 80 100
250200150100500 350
7
6
5
4
3
2
1
0
D175 – 3/4 HP
S5244SES
DP233
KEY FEATURESn 1/3 HPn Fully assembled, just plumb and plugn High impact engineered resin, exterior hardware stainless steel constructionn 1-1/2" (38mm) NPT dischargen Carbon/Ceramic mechanical seal n Piggy-back style float for automatic or manual operationn Oil-filled motor with automatic reset overload provides safe operation n Cylindrical, 5-gallon (19 L) capacity nEasily replaceable power cord with optional lengths available
SPECIFICATIONSApplications: Laundry Trays, Wet Bars, Beautician or Utility Sinks, Dehumidifier/Air-conditioning UnitsCapacities: To 48 GPM (182 LPM)Heads: To 24 FT (7.3 M)Cont. Liquid Temp: 130°F (55°C)Motor: 1/3 HPElectrical: 115 Volt, 9.8FLA, 1Ph, 60HzOperation: Vertical model, on/off: 8"/31/2" (203mm/89mm)Impeller: Thermoplastic, semi-vortex typeSolids Handling: 1/2" (50.8mm)Power Cord: 10’ (3 M) grounded SJTW-A/SJTW
MODEL NUMBER
DP233110V
S E R I E S
4
25
20
15
10
5
0 10 20 30 40 50
1000 5025 12575 150 175
7
6
5
4
3
2
1
0
CAPACITY GALLONS PER MINUTE
TOTA
L H
EAD
IN F
EET
CAPACITY LITRES PER MINUTE
TOTA
L H
EAD
IN M
ETER
SDP233 – 1/3 HP
DRAINER PRE-PLUMBED SySTEM
S5505SES
20
15
10
5
0 2512.5 37.5 50
CAPACITY LITRES PER MINUTE
CAPACITY GALLONS PER MINUTE
TOTA
L H
EAD
IN M
ETER
S
TOTA
L H
EAD
IN F
EET
50 100 15025 75 125 1756
5
4
3
2
1
0
0
DB200
DB100
KEY FEATURESn 30 GPM (114 LPM) , 2A 5-stage charging systemn Thermoplastic pump and charger enclosuren 1-1/4" (32mm) NPT threaded discharge; adapts to 1-1/4" (32mm) and 1-1/2” (38mm) pipingn Ideal for standard sump pitsn 2A multi-stage charging system (UL/CUL approved) provides most efficient charge for the batteryn Plug-in style connectors for quick and easy installationn Audio and visual alarms keep you informed of status at all timesn Check valve and battery case includedn Can be used with more than one batteryn LED Area light
SPECIFICATIONSApplications: Emergency Dewatering – Standard VolumeCapacities: To 30 GPM (114 LPM)Heads: To 16 FT (4.87 M)Cont. Liquid Temp: 77°F (25°C)Motor: 12Vdc Charger, 9A Draw at 10' (3 M) LiftElectrical: Input: 115Vac, 1Ph, 60Hz; Output: 12Vdc, 2A (5 Stages)Operation: Fully automatic; computerized monitoring, control, and alarm systemMin. Basin Diameter: 18" (5.49mm)Impeller: Thermoplastic, vane typeSolids Handling: Clear waterPower Cord: 8’ (2.4 M) pump and charger
MODEL NUMBER
DB10018T
KEY FEATURES
n 47 GPM (178 LPM), 8.0A 5-stage charging systemn Thermoplastic pump with steel case charger enclosuren 1-1/4" (32mm) NPT threaded discharge; adapts to 1-1/4" (32mm) and 1-1/2" (38mm) NPT n High volume ideal for active sump pitsn 8.0A multi-stage charging system (UL/CUL approved) with steel enclosure provides the strongest battery chargen Plug-in style connectors for quick and easy installationn Audio and visual alarms keep you informed of status at all timesn Check valve and battery case includedn Fits most new and existing sump pits
SPECIFICATIONS
Applications: Emergency Dewatering – High VolumeCapacities: To 47 GPM (178 LPM)Heads: To 18 FT (5.49 M)Cont. Liquid Temp: 77°F (25°C)Motor: 12Vdc Charger, 18A Draw at 10' (3 M) LiftElectrical: Input: 115Vac, 1Ph, 60Hz; Output: 12Vdc, 8.0A (5 Stages)Operation: Fully automatic; computerized monitoring, control, and alarm systemMin. Basin Diameter: 18" (5.49mm)Impeller: Thermoplastic, vane typeSolids Handling: Clear waterPower Cord: 8’ (2.4 M) pump and charger
MODEL NUMBER DB20018T
S E R I E S S E R I E SDB200
20
15
10
5
0 157.5 22.5 30
CAPACITY LITRES PER MINUTE
CAPACITY GALLONS PER MINUTE
TOTA
L H
EAD
IN M
ETER
S
TOTA
L H
EAD
IN F
EET
5025 75 1006
5
4
3
2
1
0
0
DB100
NOTE: Performance shown is at 12.7 Vdc with deep cycle battery (FP12V27DCC) and acid solution (FP7QTDCC).
NOTE: Performance shown is at 12.7 Vdc with deep cycle battery.
5
S5677SES S5677SES
BATTERy BACk-UP
EC2
KEY FEATURESn 4/10 HPn Class 30 cast iron constructionn 1-1/2" (38mm) NPT dischargen Carbon/Ceramic mechanical sealn Piggy-back style float for automatic or manual operationn Oil-filled motor with automatic reset overload provides safe operationn Ball bearing construction for long lifen Easily replaceable power cord with optional lengths available
SPECIFICATIONSApplications: Effluent and Wastewater Removal, Sump Drainage, Water Transfer, Flood ControlCapacities: To 62 GPM (235 LPM)Heads: To 32 FT (9.75 M)Cont. Liquid Temp: 130°F (55°C)Motor: 4/10 HP (1550 RPM); Shaded pole with thermal overloadElectrical: 115 Volt, 12.5FLA, 1Ph, 60HzOperation: Tethered models or Manual modelsMin. Basin Diameter: Simplex = 18” (457mm) Duplex = 30” (762mm) Impeller: Thermoplastic, non-clog, vortex typeSolids Handling: 1/2” (12.7mm)Power Cord: 10’ (3 M) or 20’ (6 M) 16-3, SJTW-A/SJTW
MODEL NUMBER
EC240110T
EC240110M
EC240120T
EC240120M
KEY FEATURESn 1/3 HPn Complete Class 30 cast iron constructionn 1-1/2" (38mm) NPT dischargen Carbon/Ceramic mechanical sealn Piggy-back style float for automatic or manual operationn Oil-filled motor with automatic reset overload provides safe operationn Ball bearing construction for long lifen Easily replaceable power cord with optional lengths available
SPECIFICATIONSApplications: Effluent and Wastewater Removal, Sump Drainage, Water Transfer, Flood ControlCapacities: To 55 GPM (208 LPM)Heads: To 21 FT (6.4 M)Cont. Liquid Temp: 130°F (55°C)Motor: 1/3 HP (1550 RPM); Shaded pole with thermal overloadElectrical: 115 Volt, 12.0FLA, 1Ph, 60HzOperation: Tethered models or Manual modelsMin. Basin Diameter: Simplex = 18" (457mm) , Duplex = 30" (762mm)Impeller: Thermoplastic, non-clog, vortex typeSolids Handling: 3/4" (19mm)Power Cord: 20' (6 M) 16-3, SJTW-A/SJTW
MODEL NUMBER
C333120T
EC333120M
S E R I E S S E R I E SEC3
CAPACITY GALLONS PER MINUTE
TOTA
L H
EAD
IN M
ETER
S
TOTA
L H
EAD
IN F
EET
CAPACITY LITRES PER MINUTE
30
20
10
0 20 40 60 80
500 100 150 200 250
12
10
8
6
4
2
0
40
EC2 – 4/10 HP
CAPACITY GALLONS PER MINUTE
CAPACITY LITRES PER MINUTE
TOTA
L H
EAD
IN M
ETER
S
TOTA
L H
EAD
IN F
EET
25
20
15
10
5
0 20 40
100
10 30 50
500 150
6
4
2
0
EC3 – 1/3 HP
6
S5140SES S3984SES
EFFLUENT PUMPS
7
EC4
KEY FEATURESn 4/10 HPn Class 30 cast iron constructionn 2" (50.8mm) NPT dischargen Carbon/Ceramic mechanical sealn Piggy-back style float for automatic or manual operationn Oil-filled motor with automatic reset overload provides safe operationn Ball bearing construction for long lifen Easily replaceable power cord with optional lengths available
SPECIFICATIONSApplications: Effluent and Wastewater Removal, Sump Drainage, Water Transfer, Flood ControlCapacities: To 60 GPM (227 LPM)Heads: To 40 FT (12 M)Cont. Liquid Temp: 130°F (55°C)Motor: 4/10 HP (3450 RPM); PSC with thermal overloadElectrical: 115 Volt, 10.0FLA, 1Ph, 60HzOperation: Tethered models or Manual models availableMin. Basin Diameter: 18" (457mm)Impeller: Thermoplastic, non-clog, vortex typeSolids Handling: 3/4" (19mm)Power Cord: 20' (6 M) 16-3, SJTW-A/SJTW
MODEL NUMBER
EC440120T
EC440120M
S E R I E S
40
30
20
10
020 40 60 80
TOTA
L H
EAD
IN F
EET
CAPACITY GALLONS PER MINUTE
0
4
8
12
CAPACITY LITRES PER MINUTE
TOTA
L H
EAD
IN M
ETER
S
100 200 3000
EC4 – 4/10 HP
HT3/HTX3
KEY FEATURESn 1/3 HPn Class 30 cast iron constructionn 1-1/2" (38mm) NPT dischargen Carbon/Ceramic mechanical sealn Piggy-back style float (HT3 only) for automatic or manual operationn Oil-filled motor with automatic reset overload provides safe operationn Ball bearing construction for long lifen Easily field serviceable
SPECIFICATIONSApplications: Boiler Blow-down Pits, Condensate Pits, Hot Water SumpsCapacities: 45 GPM (170 LPM)Heads: To 21 FT (6.4 M)Cont. Liquid Temp: HT = 194°F (90°C); HTX = 200°F (93°C)Motor: 1/3 HP (1550 RPM); Shaded pole with thermal overloadElectrical: 115 Volt, 12.0FLA, 1Ph, 60Hz Operation: Tethered models or Manual models availableMin. Basin Diameter: 18” (457mm)Impeller: Cast iron, non-clog, vortex typeSolids Handling: 3/4” (19mm)Power Cord: 20’ (6 M) 16-3, SJOOW-A/SJOW
MODEL NUMBER
EC440120T
EC440120M
EC440220T
S E R I E S
25
20
15
10
5
0 20 40
CAPACITY GALLONS PER MINUTE
CAPACITY LITRES PER MINUTE
TOTA
L H
EAD
IN M
ETER
S
TOTA
L H
EAD
IN F
EET
100
10 30 50
500 150
6
4
2
0
PERFORMANCE@ 70ϒF WATERTEMPERATURE
PERFORMANCE@ 194ϒF WATERTEMPERATURE
S4005SES S4912SES
SPECIALTy/EFFLUENT PUMPS
KEY FEATURESn 1/2 HP and 1 HPn Class 30 cast iron constructionn 2" (50.8mm) NPT dischargen Dual Silicon Carbide mechanical sealsn Piggy-back style float for automatic or manual operationn Oil-filled motor with automatic reset overload provides safe operationn Ball bearing construction for long lifen Easily replaceable power cord with optional lengths available
SPECIFICATIONS
Applications: Effluent and Wastewater Removal, Sump Drainage, Water Transfer, Flood Control
Capacities: To 115 GPM (435 LPM)Heads: To 90 FT (27.4 M)Max. Liquid Temp: 130°F (55°C)Motor: PSC with thermal overload; See chart in next columnElectrical: See chart in next columnOperation: Tethered models or Manual models availableMin. Basin Diameter: 18" (457mm)Impeller: Cast iron, non-clog, open vane typeSolids Handling: 3/4" (19mm)Power Cord: 10' (3 M) or 20' (6 M) 16-3, SJTW-A/SJTW
S E R I E S
CAPACITY GALLONS PER MINUTE
CAPACITY LITRES PER MINUTE
TOTA
L H
EAD
IN M
ETER
S
TOTA
L H
EAD
IN F
EET
100
75
50
25
0 30 60 90 120
0 100 200 300 400
30
25
20
15
10
5
0
EH7100 – 1 HP
EC7100 – 1 HPEH750 – 1/2 HP
EC650 – 1/2 HP
EC750 – 1/2 HP
EC6/EC7/EH7
MOTOR/ELECTRICAL
8
S3953SES
EFFLUENT PUMPS
Model Number HP FLA Volts Phase CyclesEC650120T 1/2 12.0 115 1 60EC650120M 1/2 12.0 115 1 60EC750120T 1/2 13.0 115 1 60EC750120M 1/2 13.0 115 1 60EC750220M 1/2 6.5 230 1 60EC750520M 1/2 2.3 575 3 60EC7100220T 1 6.6 230 1 60EC700220M 1 6.6 230 1 60EC7100520M 1 2.7 575 3 60HIGHHEAD MODLESEH750120T 1/2 12.0 115 1 60EH750120M 1/2 12.0 115 1 60EH7100220T 1 8.7 230 1 60EH7100220M 1 8.7 230 1 60
9
EC9
KEY FEATURESn 2 HPnClass 30 cast iron constructionn 2" (50.8mm) NPT dischargen Dual Silicon Carbide mechanical sealsn Standard controls available for automatic operationn Oil-filled motor with automatic reset overload provides safe operationn Ball bearing construction for long lifen Easily replaceable power cord with optional lengths available
SPECIFICATIONSApplications: Sewage, High-capacity Sump, EffluentCapacities: To 160 GPM (605 LPM)Heads: To 85 FT (25.9 M)Max. Liquid Temp: 130°F (55°C)Motor: 2 HP (3450 RPM); PSC with thermal overloadElectrical: 230 Volt, 11.0FLA, 1Ph, 60HzzOperation: Manual modelMin. Basin Diameter: 18" (457mm)Impeller: Cast iron, non-clog, open vane typeSolids Handling: 3/4" (19mm)Power Cord: Single Phase: 20'(6 M) 16-3, SJTW-A/SJTW
MODEL NUMBER
C9200220M
S E R I E S
100
75
50
25
0 40 80 120 160CAPACITY GALLONS PER MINUTE
CAPACITY LITRES PER MINUTE
TOTA
L H
EAD
IN M
ETER
S
TOTA
L H
EAD
IN F
EET
0 200 400 60030
20
10
0
EC9 – 2 HP
KEY FEATURESn 1/2 HPn Class 30 cast iron constructionn 2" (50.8mm) NPT dischargen Dual Silicon Carbide mechanical sealsn Oil-filled motor with automatic reset overload provides safe operationn Ball bearing construction for long lifen 600V jacketed lead for added durabilityn Easily replaceable power cord with optional lengths available
SPECIFICATIONS
Applications: High-capacity Sump, Effluent, Boiler Blow-downCapacities: To 100 GPM (378 LPM)Heads: To 50 FT (15.2 M)Max. Liquid Temp: 200°F (93°C)Motor: 1/2 HP (3450 RPM); PSC with thermal overloadElectrical: 115 Volt, 12.0FLA, 1Ph, 60HzOperation: Tethered modelMin. Basin Diameter: 18" (457mm)Impeller: Cast iron, non-clog, vortex typeSolids Handling: 3/4" (19mm)Power Cord: 20' (6 M) 16-4, SOOW-A/SOOW
MODEL NUMBER
HT750120T
S E R I E S
HT7
CAPACITY GALLONS PER MINUTE
TOTA
L H
EAD
IN M
ETER
S
TOTA
L H
EAD
IN F
EET
CAPACITY LITRES PER MINUTE
0 6030 90 120
0 100 200 300 400
16
12
8
4
0
60
45
30
15
HT7 PERFORMANCE @200ϒF WATER TEMPERATURE
HT7 PERFORMANCE @70ϒF WATER TEMPERATURE
Shown with – PW217-280 control panel (sold separately) S5081SES S5533SES
SPECIALTy/EFFLUENT PUMPS
10
ST.E.P. PLuS®
MODEL NUMBER
STEP10
STEP20
STEP30-05221
STEP30-05121
STEP30-10221
STEP30-15221
STEP50-10221
STEP50-15221
KEY FEATURESn 1/2, 1 or 1-1/2 HP, 115 or 230 Volt, single-phase, 2-wiren Superior performancen Stainless steel and composite constructionn Exclusive industry dry-run capabilityn Enclosed and self-lubricated Nylatron
® shaft-bearing resists
wear from sandn Heavy 3/8" (9.5mm) or 7/16” (11.1mm) positive drive 300 Series stainless steel hexagonal shaftn Serviceable fiberglass reinforced thermoplastic intake screenn The 10, 20, 30 and 50 GPM are industry standard 3-3/4" in diameter
SPECIFICATIONSApplications: Filtered EffluentCapacities: 10 GPM – 50 GPM (37.9 LPM – 189.3 LPM)Heads: 27 FT – 255 FT (8.2 M – 77.7 M)Motor: Water-filled, hermetically sealed, thermal overload
protected, NEMA standardElectrical: 115 or 230 Volt, 1Ph, 60HzOperations: Manual model (controls required)Minimum Diameter: 4" (102mm)Staging: (6) - 10 GPM (37.9 LPM);
(5) - 20 GPM (75.7 LPM); (3) - 1/2 HP, 30 GPM (113.6 LPM); (5) - 1 HP, 30 GPM (113.6 LPM); (6) - 1-1/2 HP, 30 GPM (113.6 LPM); (3) - 1 HP, 50 GPM (189.3 LPM); (4) - 1-12/ HP, 50 GPM (0 189.3 LPM)
Solids: 1/8" (3.2mm)Power Cord: 300 Volt “SOOW” jacketed 10 FT leads (2-wire with
ground); optional 20, 30, 50 and 100 FT lengths availableMaterials ofConstruction: 300 grade stainless steel and engineered composites
S E R I E S
CAPACITY GALLONS PER MINUTE
TOTA
L H
EAD
IN F
EET
CAPACITY LITRES PER MINUTE
TOTA
L H
EAD
IN M
ETER
S
125
100
75
50
25
0 20 40 8060
0
36
30
24
18
12
6
0
50 100 150 300200 250
STEP 50 – 1-1/2 HPSTEP 50 – 1 HP
CAPACITY GALLONS PER MINUTE
TOTA
L H
EAD
IN F
EET
CAPACITY LITRES PER MINUTE
TOTA
L H
EAD
IN M
ETER
S
0 10
250
200
150
100
50
20 30 5040
0 12575
50
25
0
25 50 75 175100 150
STEP 30 – 1-1/2 HP
STEP 30 – 1 HP
STEP 30 – 1/2 HP
CAPACITY GALLONS PER MINUTE
TOTA
L H
EAD
IN F
EET
CAPACITY LITRES PER MINUTE
TOTA
L H
EAD
IN M
ETER
S
0 10
300
225
150
75
20 30 40
0 100
80
60
40
20
0
25 50 75 125
STEP 10 – 1/2 HP
STEP 20 – 1/2 HP
S5594SES
HIGH-HEAD FILTERED EFFLUENT PUMPS
NOW AVAILABLE n Higher HP n Higher GPM n Longer Cords
ST.E.P. PLuS®
SPECIFICATIONSApplications: Effluent, Cistern, Aeration, and IrrigationCapacities: 2 gpm – 35 gpm (7.6 LPM – 132.5 LPM)Heads: 75 FT – 225 FT (22.9 M – 68.6 M)Motor: Dry-wound, double ball-bearing, double-seal, thermal
overload protectedElectrical: 115 Volt, 1Ph, 60Hz, 2-wireOperations: Manual model (controls required)Minimum Diameter: 4” (102mm)Staging: (6) - 10 gpm (37.9 LPM); (4) - 20 GPM (75.7 LPM);
(3) - 30 gpm (113.6 LPM)Solids: .080” (2.0mm)Power Cord: 10 FT (3M), 600 Volt, SJOW jacketed, 2-wire with groundMaterials ofConstruction: 300 grade stainless steel and engineered composites
MODEL NUMBER
10DOM05121 20DOM05121 30DOM05121
KEY FEATURESn 1/2 HP, 115 Volt, single-phase, 2-wiren Superior draw-down capability to 4-1/2” (114mm)
vs. 13-1/2” (343mm) on a standard NEMA 4”n25% Reduced AMP-draw 9.5 amps vs. 12.7 amps on a
standard NEMA 4” nCooler and quieter operation – eliminates expensive “flow-
inducer sleeves”nUL, CSA Listed nStainless steel and composite constructionnProven SignaSeal™ stagingn Exclusive STA-RITE dry-run capabilityn Enclosed and self-lubricated Nylatron® shaft-bearing resists
wear from abrasivesn Heavy 7/16” (12mm) positive drive 300 Series stainless steel
hexagonal shaftnStainless steel intake screen – allows for .080” solidsnPowered by STA-RITE motors
D S E R I E S
CAPACITY GALLONS PER MINUTE
TOTA
L H
EAD
IN F
EET
CAPACITY LITRES PER MINUTE
TOTA
L H
EAD
IN M
ETER
S
0 15
300
225
150
75
30 45 60
0 100
80
60
40
20
0
25 50 75 200
10 GPM
20 GPM
30 GPM
11
S5835SES
HIGH-HEAD FILTERED EFFLUENT PUMPS
12
KEY FEATURESn 4/10 HPn Class 30 cast iron constructionn 2” (50.8mm) NPT dischargenCarbon/Ceramic mechanical sealnPiggy-back style float for automatic or manual operationnOil-filled motor with automatic reset overload provides
safe operationnBall bearing construction for long lifenEasily replaceable power cord with optional lengths available
SPECIFICATIONSApplications: Sewage, High-capacity Sump, EffluentCapacities: To 110 GPM (416 LPM)Heads: To 18 FT (5.5 M)Cont. Liquid Temp: 130°F (55°C)Motor: 4/10 HP (1550 RPM); Shaded pole with thermal overloadElectrical: 115 Volt, 12.5FLA, 1Ph, 60HzOperation: Tethered modelsMin. Basin Diameter: Simplex = 18" (457mm) Duplex = 30" (762mm) Impeller: Thermoplastic, vortex typeSolids Handling: 2" (50.8mm)Power Cord: 10' (3 M) or 20’ (6 M) 16-3, SJTW-A/SJTW
MODEL NUMBER
SC440110T SC440120TSC440110M
S E R I E SSC4 SC5
KEY FEATURESn1/2 HPnClass 30 cast iron constructionn2” (50.8mm) NPT dischargenCarbon/Ceramic mechanical sealnPiggy-back style float for automatic or manual operationnOil-filled motor with automatic reset overload provides
safe operationnBall bearing construction for long lifenEasily replaceable power cord with optional lengths available
SPECIFICATIONSApplications: Sewage, High-capacity Sump, EffluentCapacities: To 130 GPM (492 LPM)Heads: To 18 FT (5.5 M)Cont. Liquid Temp: 130°F (55°C)Motor: 1/2 HP (1550 RPM); Shaded pole with thermal overloadElectrical: 115 Volt, 13.0FLA, 1Ph, 60HzOperation: Tethered models or Manual models availableMin. Basin Diameter: Simplex = 18" (457mm) Duplex = 30" (762mm) Impeller: Thermoplastic, vortex typeSolids Handling: 2" (50.8mm)Power Cord: 10' (3 M) or 20’ (6 M) 16-3, SJTW-A/SJTW
MODEL NUMBER
SC550110T
SC550120T
SC550120M
S E R I E S
CAPACITY GALLONS PER MINUTE
TOTA
L H
EAD
IN M
ETER
S
TOTA
L H
EAD
IN F
EET
CAPACITY LITRES PER MINUTE
2
0
20
15
10
5
0 40 80 120 160
2000 400 6006
4
SC5 – 1/2 HP
CAPACITY GALLONS PER MINUTE
TOTA
L H
EAD
IN M
ETER
S
TOTA
L H
EAD
IN F
EET
CAPACITY LITRES PER MINUTE
2
0
20
15
10
5
0 40 80 120 160
2000 400 6006
4
SC4 – 4/10 HP
S5691SES S3954SES
SEWAGE PUMPS
13
KEY FEATURESn1/2 HPnClass 30 cast iron constructionn2" (50.8mm) NPT dischargenDual Silicon Carbide mechanical sealsnPiggy-back style float for automatic or manual operationnOil-filled motor with automatic reset overload provides
safe operationnBall bearing construction for long lifenEasily replaceable power cord with optional lengths available
SPECIFICATIONSApplications: Sewage, High-capacity Sump, EffluentCapacities: To 160 GPM (606 LPM)Heads: To 25 FT (7.6 M)Max. Liquid Temp: 130°F (55°C)Motor: 1/2 HP (1725 RPM); PSC with thermal overloadElectrical: 115 Volt, 9.5FLA, 1Ph, 60HzOperation: Tethered models or Manual modelsMin. Basin Diameter: Simplex = 18” (457mm); Duplex = 30” (762mm) Impeller: Cast iron, vane typeSolids Handling: 2” (50.8mm)Power Cord: 10’ (3 M) or 20’ (6 M) 16-3, SJTW-A/SJTW
MODEL NUMBER
SC650110T SC650120TSC650120M
S E R I E SSC6
CAPACITY GALLONS PER MINUTE
CAPACITY LITRES PER MINUTE
TOTA
L H
EAD
IN M
ETER
S
TOTA
L H
EAD
IN F
EET
40
30
20
10
0 40 80 120 160
0 200 400 60012
8
4
0
SC6 – 1/2 HP
S5532SES
SEWAGE PUMPS
CONTINUOUS DUTY
SC7/SCC7
KEY FEATURESn1/2 HP and 3/4 HPnClass 30 cast iron constructionnSC7: 2" (50.8mm) NPT dischargenDual Silicon Carbide mechanical sealsnPiggy-back style float for automatic or manual operationn Oil-filled motor with automatic reset overload provides
safe operationn Ball bearing construction for long lifen Easily replaceable power cord with optional lengths available
SPECIFICATIONSApplications: Sewage, High-capacity Sump, EffluentCapacities: To 135 GPM (510 LPM)Heads: To 29 FT (8.8 M)Max. Liquid Temp: 130°F (55°C)Motor: PSC with thermal overload; see chart in next columnElectrical: See chart in next columnOperation: Tethered models or Manual modelsMin. Basin Diameter: Simplex = 18" (457mm) Duplex = 30" (762mm) Impeller: Cast iron, vortex typeSolids Handling: 2" (50.8mm)Power Cord: Single Phase: 20’ (6 M) 16-3, SJTW-A/SJTW;
Three Phase: 20’ (6 M) 16-4, STW-A/STWCAPACITY GALLONS PER MINUTE
CAPACITY LITRES PER MINUTE
TOTA
L H
EAD
IN M
ETER
S
TOTA
L H
EAD
IN F
EET
40
30
20
10
0 40
200
80
0 400
120 160
60012
8
4
0
SC7 – 3/4 HPSC7 – 1/2 HP
S E R I E S
14
S3983SES
MOTOR/ELECTRIC
SEWAGE PUMPS
CONTINUOUS DUTY
Model Number HP FLA Volts Phase CyclesSC& SERIES – 2" DISHCHARGESC750120T 1/2 11.2 115 1 60SC750120M 1/2 11.2 115 1 60SC750220M 1/2 5.6 230 1 60SC775120T 3/4 12.0 115 1 60SC775120M 3/4 12.0 115 1 60SC775520M 3/4 1.8 575 3 60SCC750120T 1/2 11.2 115 1 60SCC775120T 3/4 12.0 115 1 60SCC775220T 3/4 6.0 230 1 60
15
SC9/SCC9
KEY FEATURESn3/4 through 2 HPnClass 30 cast iron constructionnSC9: 2" (50.8mm) NPT discharge
SCC9: 3" (76.2mm) NPT dischargenDual Silicon Carbide mechanical seals with a secondary
self-lubricating lip sealnPiggy-back style float for automatic or manual operationnOil-filled motor with automatic reset overload provides
safe operationnBall bearing construction for long lifenEasily replaceable power cord with optional lengths available
SPECIFICATIONS
Applications: Sewage, High-capacity Sump, EffluentCapacities: To 235 GPM (889 LPM)Heads: To 54 FT (16.5 M)Max. Liquid Temp: 130°F (55°C)Motor: PSC with thermal overload; see chart in next columnElectrical: See chart in next columnOperation: Tethered models or Manual modelsMin. Basin Diameter: Simplex = 18" (457mm); Duplex = 30" (762mm) Impeller: Cast iron, non-clog, open vane typeSolids Handling: 2" (50.8mm)Power Cord: Single Phase: 20' (6 M) 16-3, SJTW-A/SJTW;
Three Phase: 20' (6 M) 16-4, STW-A/STW
S E R I E S
CAPACITY GALLONS PER MINUTE
TOTA
L H
EAD
IN M
ETER
S
TOTA
L H
EAD
IN F
EET
CAPACITY LITRES PER MINUTE
0 50 100 150 200 250
20
16
12
8
4
0
200 400 6001000 300 500 700 800 900
SC9/SCC9 – 2 HPSC9/SCC9 – 1 HP
SC9/SCC9 – 1-1/2 HP
75
60
45
30
15
S3955SES
MOTOR/ELECTRIC
SEWAGE PUMPS
CONTINUOUS DUTY
Model Number HP FLA Volts Phase CyclesSC9 SERIES – 2" DISHCHARGESC9100220T 1 8.5 230 1 60SC9100220 1 8.5 230 1 60SC9150220M 1 1/2 12.0 230 1 60SC9200220M 2 13.0 230 1 60SC9200420M 2 6.5 460 3 60SC9150420M 1 1/2 6.0 460 3 60SCC9 SERIES – 3" DISHCHARGESCC9100220T 1 8.5 230 1 60SCC9100220M 1 8.5 230 1 60SCC9100520M 1 3.5 575 3 60SCC9150220M 1 1/2 12.0 230 1 60SCC9150520M 1 1/2 3.8 575 3 60SCC9200220M 2 13.0 230 1 60SCC9200320M 2 13.0 230 3 60SCC9200520M 2 4.1 575 3 60
CAPACITY GALLONS PER MINUTE
TOTA
L H
EAD
IN M
ETER
S
TOTA
L H
EAD
IN F
EET
CAPACITY LITRES PER MINUTE
20
15
10
5
0 40 80 120 160
2000 400 600
2
0
6
4SP5 – 1/2 HP
KEY FEATURESn4/10 HPn Fully assembled, check valve includednStructural foam basin, 1-piece gas-tight covernCast iron pump with composite voluten2" (50.8mm) NPT discharge and vent connectionsn Carbon/Ceramic mechanical sealnProprietary “flush mount” design for easy shipping and storagenIncludes 4" (101.6mm) hub adaptor with stainless steel clamp
SPECIFICATIONSApplications: Sewage, High-capacity Sump, EffluentCapacities: To 110 GPM (416 LPM)Heads: To 18 FT (5.5 M)Cont. Liquid Temp: 130°F (55°C)Motor: 4/10 HP (1550 RPM); Shaded pole with thermal overloadElectrical: 115 Volt, 12.5FLA, 1Ph, 60HzOperation: Automatic tetheredBasin Size: 18" x 30" (457mm x 762mm); 30-gallon (114 L) capacityImpeller: Thermoplastic, vortex typeSolids Handling: 2" 50.8mm)Power Cord: 20' (6 M) 16-3, SJTW-A/SJTW
MODEL NUMBER
SP440120T
S E R I E SSP4
S E R I E SSP5
CAPACITY GALLONS PER MINUTE
TOTA
L H
EAD
IN M
ETER
S
TOTA
L H
EAD
IN F
EET
CAPACITY LITRES PER MINUTE
20
15
10
5
0 40 80 120 160
2000 400 600
2
0
6
4
SP4 – 4/10 HP
KEY FEATURESn1/2 HP nFully assembled, check valve includednStructural foam basinn 2-piece gas-tight cover for easy serviceabilityn Complete Class 30 cast iron pump constructionn2" (50.8mm) NPT discharge and vent flangesnCarbon/Ceramic mechanical sealn Piggy-back style float for automatic or manual operationnProprietary “flush mount” design for easy shipping and storagenIncludes 4" (101.6mm) hub adaptor with stainless steel clamp
SPECIFICATIONSApplications: Sewage, High-capacity Sump, EffluentCapacities: To 130 GPM (492 LPM)Heads: To 18 FT (5.5 M)Cont. Liquid Temp: 130°F (55°C)Motor: 1/2 HP (1550 RPM); Shaded pole with thermal overloadElectrical: 115 Volt, 13.0FLA, 1Ph, 60HzOperation: Automatic tetheredBasin Size: 18" x 30" (457mm x 762mm); 30-gallon (114 L) capacity Impeller: Thermoplastic, vortex typeSolids Handling: 2" (50.8mm)Power Cord: 20' (6 M) 16-3, SJTW-A/SJTW
MODEL NUMBER
SP550120T
16
S5565SES S5566SES
SEWAGE PRE-PLUMBED SySTEMS
17
SG11
KEY FEATURESn 2 HP; single phase, 230 Volt; 3 phase, 230/460 Voltn Superior “grinding” capabilitiesn High-torque, capacitor start/capacitor run motorn Dry-wound motor, better efficiency and serviceable, thermal over-
load protectedn Continuous-duty rated at 105°F (41°C)n Dual mechanical seals – silicon carbide/silicon carbide and
carbon/ceramicn Dual cutter design – stainless steeln Cast iron 10-vane impellern Upper and lower “shielded” ball-bearingsn Retrofit-table with ALL major competitorsn Double-cord strain relief n Replaceable 20 FT (6 M), jacketed SOW power cord
SPECIFICATIONSApplications: Sewage grinding, effluent and wastewater removalCapacities: 5 GPM – 42 GPM (18.9 – 159 LPM)Heads: 25 FT – 105 FT (7.6 M – 32 M)Motor: Dry-wound, Cap. Start / Cap. Run, thermal overload protectedElectrical: 230 Volt, 1Ph, 60Hz, 13.4FLA; 230/460B, 3Ph, 60Hz, 8.2/4.1FLAOperations: ManualMotor Housing: Cast ironPump Casing: Cast ironSeal Housing: Cast ironShaft: Stainless steelCutters: Stainless steel, 440C hardened to 55-60 Rockwell “C”, dual
cuttersImpeller: Cast iron, 10-vaneDischarge: 1-1/4" NPT (31.75mm)Power Cord: 20' FT (6 M), 14ga. SOW (3-phase), 16ga. SOW (1-phase)Materials of Construction: 300 grade stainless steel and engineered composites
S E R I E S
CAPACITY GALLONS PER MINUTE
CAPACITY LITRES PER MINUTE
TOTA
L H
EAD
IN M
ETER
S
TOTA
L H
EAD
IN F
EET
120
90
60
30
0 15 30 45 60
35
30
25
20
15
10
5
0
0 10025 50 75 200
SG11 - 2 HP
S5819SES
GRINDER PUMPS
MOTOR/ELECTRIC
Model Number HP FLA Volts Phase*SG11200220M 2 13.4 230 1SG11200320M 2 8.2/4.1 230/460 3
*3-phase models are pre-wired for 230 volt.
18
EFFLuENT/SPECIALTY PuMPSP E R F O R M A N C E C U R V E S
NOTE: Please see page 11 for S.T.E.P Plus™ Series performance curves.
CAPACITY GALLONS PER MINUTE
CAPACITY LITRES PER MINUTE
TOTA
L H
EAD
IN M
ETER
S
TOTA
L H
EAD
IN F
EET
90
80
70
60
50
40
30
20
10
0 25 50 75 100 125 150
500 100 150 200 250 300 350 400 450 500 550
2
0
4
6
8
10
12
14
16
18
20
22
24
26
EC3 – 1/3 HP
EC2 – 4/10 HP
EC750 – 1/2 HP
EH750 – 1/2 HP
EH7100 – 1 HP
EC7100 – 1 HP
EC4 – 4/10 HP
EC650 – 1/2 HPHT7 – 1/2 HP
EC9 – 2 HP
HT3/HTX3 – 1/3 HP
COMPOSITE CURVES
19
SEWAGE PuMPSP E R F O R M A N C E C U R V E S
CAPACITY GALLONS PER MINUTE
TOTA
L H
EAD
IN M
ETER
S
TOTA
L H
EAD
IN F
EET
CAPACITY LITRES PER MINUTE
60
55
50
45
40
35
30
25
20
15
10
5
0 20 40 60 80 100 120 140 160 180 200 220 240
16
14
12
10
8
6
4
2
0
1000 200 300 400 500 600 700 800 900
SC9/SCC9 – 1 HP
SC9/SCC9 – 2 HP
SC9/SCC9 – 1-1/2 HP
SC7 – 3/4 HP
SC7 – 1/2 HP
SC4/SP4 – 4/10 HPSC5/SP5 – 1/2 HP SC6 – 1/2 HP
COMPOSITE CURVESCOMPOSITE CURVES
S E R I E S S E R I E SXXXXX
20
GRINDER PuMPSP E R F O R M A N C E C U R V E S
COMPOSITE CURVES
CAPACITY GALLONS PER MINUTE
CAPACITY LITRES PER MINUTE
TOTA
L H
EAD
IN M
ETER
S
TOTA
L H
EAD
IN F
EET
120
90
60
30
0 15 30 45 60
35
30
25
20
15
10
5
0
0 10025 50 75 200
SG11 - 2 HP
S A M P L E M O D E L N U M B E R S
D = Drainer 1 = 100 00 = Not 1 = 115V 4 = 4 FT T = Automatic DC = Drainer Cast Iron 2 = 200 Applicable 2 = 208-230V/1 6 = 6 FT Tethered DB = Drainer Backup 3 = 300 08 = 1/12 3 = 208-230V/3 8 = 8 FT Switch DP = Drainer Package 4 = 400 17 = 1/6 4 = 460V/3 10 = 10 FT V = Automatic P = Pedestal 5 = 500 25 = 1/4 5 = 575V/3 15 = 15 FT Vertical PC = Pedestal Cast Iron 6 = 600 30 = 3/10 DC = Direct 20 = 20 FT Switch E = Effluent 7 = 700 33 = 1/3 Current 25 = 25 FT M = Manual EC = Effluent Cast Iron 8 = 800 40 = 4/10 EH = Effluent – High Head 9 = 900 50 = 1/2 S = Sewage 10 = 1000 75 = 3/4 SC = Sewage Cast Iron 12 = 1200 100 = 1 SCC = Sewage Cast Iron – 13 = 1300 150 = 1-1/2 Commercial 20 = 2000 200 = 2 SG = Sewage Grinder 1000 = 10 SP = Sewage Package HT = High Temperature HTX = Extra High Temperature U = Utility US = Utility Submersible
EH 7 50 1 20 T
Effluent Pump (High Head), 700 Series, 1/2HP, 115V, 20 ft. Cord, Tethered Float
DC 2 33 1 10 V
Drainer Pump (Cast Iron), 200 Series, 1/3HP, 115 Volt, 10 ft. Cord, Vertical Float
SC 9 100 2 20 M
Sewage Pump (Cast Iron), 900 Series, 1HP, 230 Volt/1PH, 20 ft. Cord, Manual Operation
T y p e S e r i e s H P V C o r d O p e r a t i o n
PRODUCT NOMENCLATURE
21
COMPOSITE CURVES
22
NOTES
NOTES
23
COMPOSITE CURVES
24
NOTES
L i m i t e d W a r r a n t y
STA-RITE® warrants, to the original consumer of the products listed below, that they will be free
from defects in material and workmanship for the Warranty Period from the date of original
installation or manufacture as noted.
Our warranty will not apply to any product that has been subject to negligence, misapplication,
improper installation or maintenance. In the event a three-phase submersible motor is operated
with single-phase power through a phase converter, or if three-leg ambient compensated,
extra-quick trip overload relays of recommended size are not used, our warranty is void.
Buyer’s only remedy and STA-RITE’s only duty is to repair or replace defective products
(at STA-RITE’s choice). Buyer agrees to pay all labor and shipping charges associated with this
warranty and to request warranty service through the installing dealer as soon as a problem is
discovered. If warranty service is requested more than 30 days after the Warranty Period has ended,
it will not be honored.
STA-RITE SHALL NOT BE LIABLE FOR ANY CONSEQUENTIAL, INCIDENTAL OR CONTINGENT
DAMAGES WHATSOEVER.
THE FOREGOING WARRANTIES ARE EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESS
WARRANTIES. IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, SHALL NOT EXTEND BEYOND
THE WARRANTY PERIOD PROVIDED HEREIN.
Certain states do not permit the exclusion of limitation of incidental or consequential damages
or the placing of limitations on the duration of an implied warranty, therefore the limitations
or exclusions herein may not apply. This warranty sets forth specific legal rights and obligations,
however, additional rights may exist, which may vary from state to state.
Supersedes all previous publications.
P r o d u c t W a r r a n t y P e r i o d
Sump/Effluent/Sewage Products Whichever occurs first:12 months from date of original instal lat ion, or 18 months from date of manufacture
©2012, PENTAIR S6367SSE 08/06/12
w w w. s t a - r i t e . c o m
293 Wright Street Delavan, WI 53115Tel: 888-782-7483 Orders Fax: 800-426-9446
CANADA: P.O. Box 9138 269 Trillium Drive Kitchener, Ontario NG2 4W5 Phone: 800-363-7867 Orders Fax: 800-426-9446