Premium 3000 Manual

8/12/2019 Premium 3000 Manual

1/16

PREMIUMModel : 3000

COMPATIBLE WITHALL DiSEqC 1.2 RECEIVERS

Full specifications and associated document for the DiSEqC system, which is a communciationbus between satellite receivers and peripheral equipment using only the existing coaxial cable.DiSEqC can be integrated into consumer satellite installations to replace all convertional switching.

Model : 3000

PREMIUM Digital

Smart Software

Achiev es Very High

Positioning ResolutionOf 0.1 Degree.

CompatibleWith All DiSEqC 1.2ReceiversSOFTWARE LIMITS PROTECTION

Full specifications and associated document for the DiSEqC system,which is a communciation bus between satellite receivers andperipheral equipment using only the existing coaxial cable.DiSEqC can be integrated into consumer satellite installations toreplace all convertional switching.

SoftwareLimits ProtectionTHE BEST CHOICE TO MOTORIZE YOUR SATELLITE ANTENNA

REGISTRATION NOTES 2006. All rights reserved.

All brand name. and the other logos are owned and may be Registered.All other trademarks are the properties of their respective owner.

RoHSconform

DiSEqC 1.2


2/16

1

INSTALLING THE MOUNT

1. Assemble the H-H Mount as the following diagram.

2. Ensure the mounting tube indica tes 0 . lf not, sit it to exactly 0 using the manual buttons on the

bottom of the mount. The cable must be connected to the receiver which must be switched on.

3. Make sure the mounting pole is exactly verticalbefore installation.

4. Fix the H-H Mount onto the Mounting pole or stand and ti ghten the two U-bolts evenly. Make

sure there is no obstacle facing the southern sky, such as a tree or building.


3/16

2

ALIGNMENT OF THE MOUNT

1. Finding TRUE SOUTH.

Attaching the Antenna Dish to the Mount. Make sure the dish is at the center of the mounting tube.Rotate the mount together with the antenna toward TRUE SOUTH. You can find the TRUESOUTH using the magnetic variation table and a compass that indicates the MAGNETIC SOUTH.

2. Setting Elevation Angle.(A)Adjust the motor elevation angle using an inclinoneter or the Latitude scale on one sides of theMotor according to the Latitude of your position.

3. Setting Declination Angle.(B)ANGLE TABLE.Find the Declination Angle on the attached

Set the Declination Angle by the scale on the antenna dish, The reading on the antenna scale

should be: 35 -DECLINATION ANGLE

4. Drive the antenna east and west via the manual buttons on the bottom of the Mount to check ifthe reception arc is correct. lf not, adjust the direction, elevation, and declination angle to find the

best reception.

P.S. To ensure power to drive the antenna, first connec t the Mount to the receiver or interface box via coaxial cable.


4/16

3

ADJUST THE TUBE LOOSE

If you incur the problem of loose tube, follow the procedure to solve it:

1.Loosen the 4 screws (#1 on the picture) a little

2.Tighten the screw (#2 on the picture) a little.

3.Tighten the 4 screws (#1 on the picture) securely

CABLE CONNECTION

Connect the DiSEqC Mount and the coaxial cable (RG-6/U)per the following diagram.


5/16

4

DiSEqC 1.2 OPERATION

The DISEqC Motor is designed for DiSEqC 1.2 Receiver. The commands of the receivers might bedifferent, but similar. Please refer to the manual of the DiSEqC 1.2 receiver.

1.Go East / West:

2.Fine Tune East / West:

3.Store nn:

4.Goto nn:

5.Goto 0 :

6.Re-synchronize / Shift:

Rotates the antenna to East / West.

Rotates the antenna East / West for one step.

Store Satellites Position nn (01~60).

Rotates Motor to Satellite Position nn (01~60).

Rotates the Motor to 0 as a reference point.

(a)Rotate the motor to a position by Goto command.(b)Rotate the motor East / West to a better position.(c)Send Re-synchronize commands to the motor. The original position will be shifted to the new position. All the other Satellite positions are also changed.

Goto X Function1.See your receiver manual and select the type of installation in GotoXmode.

2.Fill in the empty spaces in the receiver's menu with the Latitudeand Longitudevalues.Whenthe values have been correctly received, the receiver drives the Motor to the calculated position.

3.Rotate the locked together antenna and motor slightly clockwise or anticlockwise until you findan image on the TV-screen connected to the receiver or the signal and quality, and then tightenthe fixing screws.

LED INDICATOR

The 2 LED indicators on the bottom of the motor can show the following information:

Function Status

Power on

Drive East

Drive West

Halt

Store

Call

East LimitWest Limit

Limit off

Goto X

Stop East Limit

Stop West Limit

LED1 & LED2 Blink every 2 Seconds

LED1 Blinks once

LED2 Blinks once

LED1 & LED2 Blink once

LED1 Blinks Twice

LED2 Blinks Twice

LED1 Blinks 3 timesLED2 Blinks 3 times

LED1 & LED2 Blink 3 times

LED1 & LED2 Blink 4 times

LED1 Keeps Blinking

LED2 Keeps Blinking


6/16

5

HARDWARE RESET BY RECEIVER

1. Execute the command: Go To Reference (Go To "0").

2. Cut off the power by disconnecting the coaxial cable.

3. Reconnect the coaxial cable.

4. Execute the command: Shift "0".

5. Then, its memory erased, the receiver rewrites the satellite table to initial one and corrects the "0".

HARDWARE RESET BY DiSEqC MOTOR

1. Cut off the power by disconnecting the coaxial cable.

2. Press and hold both EAST / WEST buttons for 5 seconds.

3. Reconnect the coaxial cable.

4. LED1 and LED2 blink for 5 seconds.

5. Then, its memory erased, the receiver rewrites the satellite table to initial one and corrects the "0"

BUILT-IN SATELLITE TABLE RESET

1. Press and hold both EAST / WEST buttons for 5 seconds.

2. LED1 and LED2 blink for 5 seconds.

3. Then, its memory erased and rewrites the built-in Satellite table to initial one.


7/16

6

Troubleshooting the H-H Mount

Symptoms Check points

The manual buttons don't work

The Mount doesn't work

The Mount stops at some positionsand can't go farther

The Mount runs intermittently

The Mount sometimes runs fast and

sometimes runs slowly

All satellite positions are not correct.

1. Connect the Motor to the receiver via coaxial cable first and make sure the receiver power is on.

1. Ensure all cables and power are connected well.2. Check if the receiver is DiSEqC 1.2. lf not, try to use our interface box.3 .Check whether the dish is too heavy.

1. Disable the software limits and move the motor again.2. Make sure the Mount or antenna are not interfered with any other item.

1. Make sure the antenna is not too heavy or too large.2. Check if the cable quality is good enough. Try a better RG- 6U cable.3. Check whether the output power of the receiver is higher than 350mA.

1. The speed of the Mount varies with receiver output voltage (13/18Vdc)

1. Correct this problem via the "Goto 0"Function, the Mount will go to 0 degree as a reference point.

OR

2. Goto a satellite position via receiver or interface box. Wait for about 30 seconds until the motor stops.3. Drive the antenna East or West until the reception of this satellite is clear.4. Use "Re-calculate" or "Shift" Function to correct position.


8/16

7

SPECIFICATION

H-H Mount

Protocol DiSEqC 1.2 & Goto "X"

Compatible Receiver Receiver with DiSEqC 1.2 or lnterface Box

Antenna Size 120 cm Max.

Speed 1.9 / sec (at 13V) : 2.5 / sec (at 18V)

80 East ~ 80 West ( 160 )

25~75

13 / 18Vdc

13 / 18Vdc

50 mA (Standby)200mA (Normal)350mA (Max.)

Azimuth Angle

Elevation Angle

lnput Voltage

Output Voltage

Power Consumption

Satellite Positions

Calibration Function

Manual East/West Buttons

Limit Protection

Positioning Sensor

Connector

Weight ( Mount )

Dimension ( Mount )

60 positions

Yes ( Go to 0 )

Yes (Build-in on the bottom of the Mount)

1.Fixed type with microswitches2.Programmable Software Limit3.Current Limit

High Resolution Hall Effect Sensor

F- Type

3.1 Kg (Net) / 3.5 Kg (Gross) (~ 8 lbs)

345 x 168 x 110 mm3 (Gross)

DiSEqC is a trademark of EUTELSATTM


9/16

8

ELEVATION AND DECLINATION ANGLE TABLE

Your SiteLatitude

ElevationAngle

DeclinationAngle

DishBracketAngle

Your SiteLatitude

ElevationAngle

DeclinationAngle

DishBracketAngle

0

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

1819

20

21

22

23

24

25

26

27

28

29

30

31

32

33

90

89

88

87

86

85

84

83

82

81

80

79

78

77

76

75

74

73

7271

70

69

68

67

66

65

64

63

62

61

60

59

58

57

0.0

0.2

0.4

0.5

0.7

0.9

1.1

1.2

1.4

1.6

1.8

1.9

2.1

2.3

2.4

2.6

2.8

3.0

3.13.3

3.4

3.6

3.8

3.9

4.1

4.2

4.4

4.5

4.7

4.8

5.0

5.1

5.2

5.4

35.0

34.8

34.6

34.5

34.3

34.1

33.9

33.8

33.6

33.4

33.2

33.1

32.9

32.7

32.6

32.4

32.2

32.0

31.931.7

31.6

31.4

31.2

31.1

30.9

30.8

30.6

30.5

30.3

30.2

30.0

29.9

29.8

29.6

34

35

36

37

38

39

40

41

42

43

44

45

46

47

48

49

50

51

5253

54

56

58

60

62

64

66

68

70

72

74

76

78

80

56

55

54

53

52

51

50

49

48

47

46

45

44

43

42

41

40

39

3837

36

34

32

30

28

26

24

22

20

18

16

14

12

10

5.5

5.6

5.8

5.9

6.0

6.1

6.3

6.4

6.5

6.6

6.7

6.8

6.8

7.0

7.1

7.2

7.3

7.4

7.57.6

7.6

7.8

7.8

8.0

8.2

8.3

8.4

8.4

8.5

8.6

8.6

8.6

8.7

8.7

29.5

29.4

29.2

29.1

29.0

28.9

28.7

28.6

28.5

28.4

28.3

28.2

28.2

28.0

27.9

27.8

27.7

27.6

27.527.4

27.4

27.2

27.2

27.0

26.8

26.7

26.6

26.6

26.5

26.4

26.4

26.4

26.3

26.3


10/16

Pre-Stored Satell ites Table

N0

1

2

3

4

5

6

78

9

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

26

Satellite Name Longitude ( +West / -East)

TELESTAR 12

ATLANTIC BIRD 1

ATLANTIC BIRD 2

NILESAT 101.102. ATLANTIC BIRD 4

ATLANTIC BIRD 3

AMOS 2/3

INTELSAT 10-02

SIRIUS 4

EUTELSAT W3A

EUROBIRD 9A

EUTELSAT W1

HOTBIRD 6,7A,8

EUTELSAT W2

ASTRA 1F/H/KR/L/M

EUTELSAT W6

EUROBIRD 2

BADR 4-6

ARABSAT 2B

ASTRA 1D

EUTELSAT W4

EXPRESS AM-1

TURKSAT 2A/3A

EXPRESS AM22

INTELSAT 902

ABS 1

NSS 7

15 W

12.5 W

8 W

7 W

5 W

4 W

1 W4.8 E

7 E

9 E

10 E

13 E

16 E

19.2 E

21.6 E

25.5 E

26 E

30.5 E

31.3 E

36 E

40 E

42 E

53 E

62 E

75 E

22 W


11/16


12/16


13/16


14/16


15/16


16/16

Premium 3000 Manual

Documents

Transcript of Premium 3000 Manual