Preliminary General Arrangement Drawing Rev A · Preliminary General Arrangement Drw. ERS20130724-1...
2
56.000 83.100 8.000 intake vents (3X) input CB handle status display FRONT 40.000 44.600 TOP 40.000 exhaust vents (3X) LEFT NEMA 3R Preliminary General Arrangement Drw. ERS20130724-1 A Notes: 1) The unit weight is approximately 2) The enclosure is NEMA 3R and employs fans and filters. FIlters are repalaceable from the outside 3) The standard color is ANSI-61 grey 4) Cable entry is from the bottom rear 5) The fans and filters are not shown (just the housings) so that other internal components can be seen ERS 072413 DO NOT SCALE DRAWING SHEET 1 OF 2 UNLESS OTHERWISE SPECIFIED: SCALE: 1:50 REV DWG. NO. A SIZE TITLE: NAME DATE COMMENTS: Q.A. MFG APPR. ENG APPR. CHECKED DRAWN FINISH MATERIAL INTERPRET GEOMETRIC TOLERANCING PER: DIMENSIONS ARE IN INCHES TOLERANCES: FRACTIONAL ANGULAR: MACH BEND TWO PLACE DECIMAL THREE PLACE DECIMAL PROPRIETARY AND CONFIDENTIAL THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF UTILITY SYSTEMS TECHNOLOGIES INC. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF UST, INC. IS PROHIBITED. 5 4 3 2 1 UTILITY SYSTEMS TECHNOLOGIES, INC. P.O. BOX 110, LATHAM, NEW YORK 12144 Sample
Transcript of Preliminary General Arrangement Drawing Rev A · Preliminary General Arrangement Drw. ERS20130724-1...
56.000
83.1
00
8.00
0
intake vents (3X)
input CB handle
status display
FRONT
40.0
00
44.6
00
TOP
40.000
exhaust vents (3X)
LEFT
NEMA 3RPreliminary General Arrangement Drw.
ERS20130724-1 A
Notes:
1) The unit weight is approximately
2) The enclosure is NEMA 3R and employs fans and filters. FIlters are repalaceable from the outside
3) The standard color is ANSI-61 grey
4) Cable entry is from the bottom rear
5) The fans and filters are not shown (just the housings) so that other internal components can be seen
ERS 072413
DO NOT SCALE DRAWING SHEET 1 OF 2
UNLESS OTHERWISE SPECIFIED:
SCALE: 1:50
REVDWG. NO.
ASIZE
TITLE:
NAME DATE
COMMENTS:
Q.A.
MFG APPR.
ENG APPR.
CHECKED
DRAWN
FINISH
MATERIAL
INTERPRET GEOMETRICTOLERANCING PER:
DIMENSIONS ARE IN INCHESTOLERANCES:FRACTIONALANGULAR: MACH BEND TWO PLACE DECIMAL THREE PLACE DECIMAL
PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED IN THISDRAWING IS THE SOLE PROPERTY OFUTILITY SYSTEMS TECHNOLOGIES INC. ANY REPRODUCTION IN PART OR AS A WHOLEWITHOUT THE WRITTEN PERMISSION OFUST, INC. IS PROHIBITED.
5 4 3 2 1
UTILITY SYSTEMS TECHNOLOGIES, INC.P.O. BOX 110, LATHAM, NEW YORK 12144
Sample
output connections (A, B, C, N)
input connections (A, B, C,)
cable entry openings (2X)
optional heater junction box
AERS20130724-1
500 kVA Sure-Volt, NEMA 3RAuto-transformer VersionPreliminary General Arrangement Drw.
cover plates are provided
(see note below)
input and output connections are made to distribution blocksmounted on a rear facing panel. Cables enter rear floor of enclosureand loop up and back down to enter the top of teh distributionblocks. The number and size of the input and output cables mustbe supplied to UST as early as possible.
DO NOT SCALE DRAWING
UNLESS OTHERWISE SPECIFIED:
SCALE: 1:50
REVDWG. NO.
ASIZE
TITLE:
NAME DATE
COMMENTS:
Q.A.
MFG APPR.
ENG APPR.
CHECKED
DRAWN
FINISH
MATERIAL
INTERPRET GEOMETRICTOLERANCING PER:
DIMENSIONS ARE IN INCHESTOLERANCES:FRACTIONALANGULAR: MACH BEND TWO PLACE DECIMAL THREE PLACE DECIMAL
PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED IN THISDRAWING IS THE SOLE PROPERTY OFUTILITY SYSTEMS TECHNOLOGIES, INC. ANY REPRODUCTION IN PART OR AS A WHOLEWITHOUT THE WRITTEN PERMISSION OFUST, INC. IS PROHIBITED.
5 4 3 2 1
UTILITY SYSTEMS TECHNOLOGIES, INC.P.O. BOX 110, LATHAM, NEW YORK 12144
SHEET 2 OF 2
Sample
