Precast Wall Panels
Transcript of Precast Wall Panels
-
7/28/2019 Precast Wall Panels
1/9
Structural wall panel
Architectural wall panel
Cladding wall panel
Sandwich wall panel
Wall Panels
-
7/28/2019 Precast Wall Panels
2/9
Assorted styles and
colours
Reveals and other patterns
Painted finish
Bolted, welded and knife
connections available
Wall Panels
-
7/28/2019 Precast Wall Panels
3/9
Wall Panel Sections
STRAND DESIGN AS REQD
MAX= 13-01/2 X 1/2 CHAMFER
(EXTERIOR ONLY)
MIN.
90
STRAND DESIGN AS REQD
INSULATION
MAX= 13-0
1/2 X 1/2 CHAMFER(EXTERIOR ONLY)
VARIES
STRAND DESIGN AS REQD
INSULATION
MAX= 13-01/2 X 1/2 CHAMFER
(EXTERIOR ONLY)
VARIES
Solid Cladding Panel
Insul. Cladding/Structural Panel
Insulated Ribbed Panel
-
7/28/2019 Precast Wall Panels
4/9
Bracing support during installation
Wall Panel Connection Details
PRECAST PANEL
T/O WALL PANELS
HEAVY DUTY REGULAR
PIPE BRACING
C.I.P. CONTINUOUS
CONCRETE BLOCK
BY OTHERS
T/O FOOTING
Structural Notes
Design wind loads - 1.2kPa (25PSF) Install braces at 1220 (4-0) nominal spacing, at panels supported by knife connections
the braces can be added to the supporting panels.
Cast in place concrete to be minimum 30 MPa Braces to be anchored using 5 long 5/8 HILTI HUS-H screw anchor or approved equivalent
installed in accordance with manufacturers recommendations Screw anchors to have minimum 3 embedment in wall panels
Screw anchors to have minimum 4 embedment in cast in place concrete
-
7/28/2019 Precast Wall Panels
5/9
Wall Panel Connection Details
WL01 WL02Bottom connection cast in plate Bottom connection dowel connection
WL03 WL04Bottom connection cast in plate Deck bearing back to back connection
WL05 WL06Lateral connection T/O panel Deck bearing / Beam connection
INSULATED WALL PANEL
DOWEL DRILLED ANDEPOXIED INTO PANEL
PLATE CAST IN PANEL
DESIGN WILL VARY
SCREWED ANCHOR OR
EQUIVALENT CONNECTION
PLASTIC SHIMS AND
CONT. CAULKING ROD
BOTH SIDES
POURED REINF. CONC.
FOOTING/FOUNDATION WALL
BY OTHERS
INSULATED WALL PANELCOIL LOOP INSERT
DOWEL 2/PANEL U.N.O.
DP. HOLE DRILLED ON SITE
PLASTIC SHIMS AND
CONT. CAULKING, BACKER
ROD BOTH SIDES
POURED REINF. CONC.
FOOTING/FOUNDATION WALL
BY OTHERS
CAST IN PLATE FOR
STRUCTURAL CONNECTION
PERCAST WALL PANEL
DRYPACKS
VOID SOLID
SCREWED ANCHOR OR
EQUIVALENT CONNECTION
PLASTIC SHIMS AND
CONT. CAULKING ROD
BOTH SIDES
POURED REINF. CONC.
FOOTING/FOUNDATION WALL
BY OTHERS
METAL DECK ROOF
CAST IN PLATE FOR
STRUCTURAL CONNECTION
STRUCTURAL BEAM
KEEP INSUL. BACK
@ STEEL ELEV.
STEEL STRUCTURE
BY OTHERS
CONT. ANGLE WELDED
TO TOP OF STEEL
SPACER PLATES, COIL
LOOP, WASHERS &
SLOTTED PLATECAP FLASHING
BY OTHERS
INSULATED WALL
PANEL
CAP FLASHING
BY OTHERS
METAL DECK ROOF
STRUCTURAL BEAM
CAST IN PLATE FOR
STRUCTURAL CONNECTION
INSULATED WALL PANEL
-
7/28/2019 Precast Wall Panels
6/9
Wall Panel Connection Details
WL07 WL08Exterior 90 corner connection Exterior 90 corner connection
WL09 WL10Intersecting 90 corner connection Exterior 90 corner connection
WL11 WL12Panel to panel connection Panel to panel vertical
COIL LOOP INSERT,WASHERS, BOLTS AND
SLOTTED PLATE
REMOVE INSUL. @
INSERT LOCATIONSINSULATED WALL PANEL
INSULATED WALL PANEL
CONT. CAULKING AND
BACKER ROD BOTH SIDES
INSULATED
WALL PANEL
CAST IN PLATECAST IN PLATE
L-100x100x12x100LG
ANGLE
CONT. CAULKING, BACKER
ROD BOTH SIDES
INSULATED
WALL PANEL
CONT. CAULKING AND
BACKER ROD BOTH SIDES
COIL LOOP INSERT, WASHERS,
BOLTS AND SLOTTED PLATE
REMOVE INSUL. @
PLATE LOCATION
CAST IN PLATE
L-100x100x12x100LG
ANGLEINSULATED
WALL PANEL
CAST IN PLATE
COIL LOOP INSERT
BAR W/2 LG. THREAD
ONE END
13mm RECESS
CONT. CAULKING, BACKER
ROD BOTH SIDES
COIL LOOP INSERT, WASHERS,
BOLTS AND SLOTTED PLATE
CONT. CAULKING, BACKERROD BOTH SIDES
REMOVE INSUL. @
INSERT LOCATIONS
COIL LOOP INSERT, WASHERS,
BOLTS AND SLOTTED PLATE
WALL PANEL
13mm CHAMFER
13mm CHAMFER
WALL PANEL
CONT. CAULKING, BACKER
ROD BOTH SIDES
-
7/28/2019 Precast Wall Panels
7/9
Wall Panel Connection Details
WL13 WL14Panel edge @ head of man door (top view) Panel edge @ head of man door (side view)
WL15 WL16Panel edge @ window sill on exterior panels Door jam @ O.H. door #1
WL17 WL18Door jam @ O.H. door #2 Panel to column connection
INSULATED
WALL PANEL
13mm WIDE DRIP
MANDOOR
JOINT TREATMENTBY OTHERS
KEEP INSUL. BACKFROM PANEL EDGE
G.C. NOTE:ALL FLASHING @MAN DOORS(NOT BY STUBBES)
DOOR AND FRAMEBY OTHERS
KEEP INSUL. BACKFROM PANEL EDGE
INSULATED WALL PANEL
13 x13 CHAMFER MAN DOOR
CONNECTION OF DOORTO PANEL BY OTHERS
G.C. NOTE:ALL FLASHING @ MAN DOORS(NOT BY STUBBES)
13x13 CHAMFER
KEEP INSUL. BACK
FROM PANEL EDGE
WINDOW, FRAME AND
CAULKING BY OTHERS
INSULATED WALL PANEL
KEEP INSUL. BACK
FROM PANEL EDGE
INSULATED
WALL PANEL
CAST IN PLATE
CAST
IN PLATE
O.H. DOOR
BY OTHERS
OH DOOR
ELEVATION 1
CONNECTION OF BENT
PLATE TO PANEL PLATE
BY OTHERS
O.H. DOOR AND TRACK
SUPPLIED CONNECTION
DESIGN BY OTHERS
INSULATEDWALL PANEL
CAST IN PLATE
CAST IN
PLATE
ELEVATION 2GARAGE
DOOR
OPENING
STRUCTURAL COLUMN
CONNECTION OFWINDOWS / DOOR TOPANEL BY OTHERS
SLOTTED ANGLEBY OTHERS
THREADED ROD
PLASTIC SHIMS
WINDOW, FRAME ANDCAULKING BY OTHERS
PRECASTWALL PANEL
HALFEN ANCHOR(VERTICAL)
-
7/28/2019 Precast Wall Panels
8/9
Wall Panel Connection Details
WL19 WL20Knife connection to beam Knife connection to ADJACENT PANEL
WL21 WL22Laterial connection @ hung panel Reveal locations and profile
WL23 WL24Scupper detail #1 Scupper detail #2
KNIFE PLATE CAST
INTO PANEL
KNIFE PLATE CAST
INTO PANEL
STEEL BEAM
PRECAST
WALL PANEL
STEEL BEAM
PRECAST
WALL PANEL
KNIFE PLATE
CAST INTO
PANEL
KNIFE PLATE
CAST INTO
PANEL
BEARING ANGLE
BEARING
ANGLE
ENSURE ALL KNIFES ARE
SHIMMED AND DRYPACKED
W/NON SHRINK GROUT
PRECAST
WALL PANEL
PRECAST
WALL PANEL
SPACER PLATES, COIL
LOOP, WASHERS AND
SLOTTED PLATE
CONT. ANGLE WELDED
TO TOP OF STEEL
STEEL BEAM
PRECAST
WALL PANEL
PRECAST REVEAL
SIZE AND DESIGN
VARIES PER CONTACT
VARIES
VARIES
VARIES
CAP FLASHING
BY OTHERS
METAL DECK ROOF
STEEL STRUCTURE
BY OTHERS
SCUPPER
INSULATED
WALL PANEL
CAP FLASHING
BY OTHERS
INSULATED WALL PANEL
CAST IN PLATE FOR
STRUCTURAL CONNECTION
SCUPPER
METAL DECK ROOF
-
7/28/2019 Precast Wall Panels
9/9
1. General:a. Included:
i. Precast Wall Panels
1. Architectural & Structural Panels.2. Sandwich & Cladding styles.ii. Structural connections.iii. Backer rod and caulking of panel joints.
2. Reference Material:a. CSA A23.4-09: Precast Concrete Material & Construction.b. Precast Concrete Institute (PCI): Manual on Design of Connections for Precast.c. Precast Concrete Institute (PCI): Design Handbook Precast & Prestressed Concrete.
3. Shop Drawings:a. Approval drawings will require a review by the Contractor & Design Firms under contract of each project.
Discrepancies, questions & verification of design is required and returned in writing prior to commencement ofproduction.
b. Production drawings will bear a signed and sealed Engineer stamp, slab locations, identification marks, connectiondetails, dimensions, openings larger than 6 in size, loadings and other relative information.
4. Quality Assurance:a. Conformity to PCI manual on design of connection for Precast Prestressed Concrete,
PCI Design Handbook Precast & Prestressed Concrete, CSA A23.4.
5. Accessories:a. Shim pads: Plastic or steel to assist transfer of loads.b. Cast in inserts / plates or similar relevant to remainder of structure.c. Connections (i.e. knife, bolted, welded) between panel units.
6. Finishes:a. Steel form.b. Troweled.
c. Sandblast.d. Ribbed pattern.e. Painted (with sand additive option).f. Exposed aggregate (vary with availability contact Stubbes for current options).g. Colours (vary with availability contact Stubbes for current options).
7. Installation:a. Install panels with corresponding identification mark as indicated on production / shop drawing.b. Ensure connections provided as detailed on production / shop drawing.c. Backer rod and caulking of joints between precast panels and foundation.
8. Excluded items related to precast and installation:a. Drypacking / infill of gap between precast and structure.b. Perimeter caulking between precast and structure (other than foundation).c. Winter heat / protection from weather conditions.d. Site / field dimensions (Contractor and Project Designers responsible to provide information during
shop drawing approval).
Wall Panel Specifcations