Practice Questions Graphicsij

1

PRACTICE QUESTIONS GRAPHICS These questions have been taken from official syllabus for PYP-004 and contribute to the preparation for Theory Test and also for Final Examination.

2014

M.B. Ahmed Lecturer, CASS, KFUPM

1/12/2014

2

Lectures Plan

First Lecture Objectives

Introduction to Graphics & Engineering Drawing

The concept of views

Orthographic Projection

Concept of Hidden Lines

Exercises in the book (page numbers: 05-12)

Second Lecture Objectives

Introduction to AutoCAD User Interface

Drawing Environment (Status bar, Drawing Units & Drawing Limits)

Draw Commands

Drawing Lines (Direct Distance Entry Method)

Dimension Tool bar

Lesson one in the book

Third Lecture Objectives

Draw Commands

Lesson two and three in the book

Fourth Lecture Objectives

Modify Commands

Practice Exercises in the book

Fifth Lecture Objectives

Continuation of Modify Commands

Assessment

3

INSTRUCTIONS:

These questions are lecture-wise arranged. Students should attempt the questions under

LECTURE ONE heading after first week and so on.

In the end there are solved exercises.

All the questions in this file are important for Theory Test and also helpful for Final Exam

LECTURE ONE

CONCEPTS OF ORTHOGRAPHIC VIEWS

1. Orthographic Projection is used to show two dimension surface of a three dimensioned object.

a. True

b. False

2. In third angle of projection, the top view of an isometric projection is projected on ____ plane

a. Front

b. Side

c. Top

3. Orthographic drawing refers to a 2D (two-dimensional) representation of an object in a view that shows only ----------- at a time.

a. One side

b. Two sides

c. Three sides

d. All sides

4. The following symbol is used to show:

:

a. First angle of projection b. Third angle of projection

5. Which one of the following figure is plan for the object?

4

ANS__________

6. How many hidden lines will be drawn in front view of the object shown in Figure 01?

a. one

b. two

c. Four

d. None

5

7. How many hidden lines will be drawn in Right End Elevation view of the object shown in Figure 02?

a. Four

b. One

c. Two

d. Six

8. Name the Orthographic projection view a in fig-03?

a. Plan

b. Front

c. R.H End Elevation

d. L.H End Elevation

6

9. How many hidden lines will be drawn in the top view of the object shown in above figure?

a. 2

b. 4

c. 6

d. No hidden lines will be drawn

10. In the adjacent figure, the front view dimensions are--------------?

a. 80, 40, 10, 20

b. 40, 20, 30

c. 80, 20, 10, 05

d. 10, 20,70, 60




7


13. What type of view is it?

a. Perspective

b. Orthographic

c. Isometric

14. In the front view of figure (Q:15), the hole feature will be shown as _____.

a. Continuous lines

b. Hidden Lines

c. Broken Lines

15. In third angle of projection, the front view of an isometric projection is projected on ____ plane

a. Front

b. Side

c. Top

16. What type of drawing is it?

a. Isometric

b. Orthographic

c. Isobaric

d. None of above

8

17. What is the angle of projection, for the adjacent figure?

a. First Angle

b. Second Angle

c. Third Angle

d. None of above

18. Which dimensions will be used for rectangular cut on the base of figure-04?

a. 15-35-120-15

b. 15-50-15-50

c. 35-120-35-120

9

19. How many hidden lines will be drawn in the top view of the object shown in above figure?

a. 2

b. 4

c. 6

d. No hidden lines will be drawn

10

LECTURE TWO

INTRODUCTION TO AUTOCAD AND DRAWING AIDS

20. In which bar do you find the Ortho & Osnap icon?

a. Draw toolbar

b. Modify toolbar

c. Status bar

d. Object properties toolbar

21. Drafting Settings dialogue box can be accessed using _____________

a. Tools Menu

b. Format Menu

c. Edit Menu

22. Always use __________ to pick dimension line origins.

a. Ortho Mode

b. Snap

c. Osnap

23. To print drawings we should use ______ space

a. Model

b. Paper

24. You can quickly open an existing document using ------tool bar

a. Standard

b. Menu

c. Property

11

25. Which of the following can be drawn using Object Property Tool Bar

a. Circle

b. Rectangle

c. Hidden Line

26. Which of the following mode you would use to pick the dots on regular grids?

a. OSNAP

b. SNAP

c. ORTHO

27. In Auto-CAD object snap is used to pick accurately--------------of a line.

a. End point

b. Mid point

c. Nearest point

d. All of above

28. Format and Tools Buttons lie on ------Tool Bar

a. Menu

b. Standard

c. Property

29. The value of drawing units is determined before you draw.

a. True

b. False

30. Regular pattern of dots displayed on the screen and acting as a visual aid are called______

a. Drawing Units

b. Drawing grid

31. In Orthographic projection, projection lines are ------------ to image plane.

a. parallel

b. perpendicular

c. at 45 degrees

32. In orthographic projection, the perpendicular distance between the views

12

is________

a. 10 mm

b. 20mm

c. Same

33. In AutoCAD user interface, ________ displays prompts and messages.

a. Command Window

b. Drawing Area

c. Standard Tool Bar

34. In AutoCAD, Ortho command is used to draw--------------lines.

a. Perpendicular

b. Inclined

c. Polyline

d. All of above

35. Which of the following pairs are found on Status Bar

a. Snap and Grid

b. Units and Limits

c. Dimension and Text

36. _______ is used to change the line type.

a. Standard Tool Bar

b. Property Tool Bar

c Format Tab

13

LECTURE THREE

AUTOCAD DRAW COMMANDS

37. What does this icon represent?

a. Rectangle

b. Line

c. Parallelogram

38. Name the AutoCAD tool bar where you find the hidden Line Types?

a. Draw Toolbar

b. Modify Toolbar

c. Command Line

d. Object Properties Toolbar

39. In AutoCAD, a polyline can be drawn by:

a. Draw Tool bar

b. Modify tool bar

c. Object properties tool bar

40. In AutoCAD, a circle can be drawn by

a. centre, radius

b. Centre Diameter

c. Start, centre, end

d. 3 points

e. All of the above

41. After starting circle command, _______ should be specified first.

a. Radius of circle

b. Diameter of circle

c. Centre point of circle

14

42. In AutoCAD, an arc can be drawn by the following command:

a. Start, End, Radius

b. Start, End, Direction

c. Three Points

d. All of above

43. Draw Commands can be started by _____ ways

a. one

b. Two

c. Three

44. Which command would you use to draw connected sequence of many line segments with different thickness?

a. Continuous Line Command

b. Multi Line Command

c. Polyline Command

45. The _____ command is used to dimension along straight lines.

a. DIMDIAMETER

b. DIMALIGNED

c. DIMLINEAR

15

LECTURE FOUR

AUTOCAD MODIFY COMMANDS

46. AutoCAD draw tool bar symbol is used for ------------command.

a. Pentagon

b. Rectangle

c. Array

d. Construction line

47. Fillet command can be started using draw-toolbar

a. True

b. False

48. Identify the following symbol, found in modify tool bar.

a. Offset

b. Scale

c. Mirror

d. Cloud

49. Which command can be started using this icon?

a. Offset

b. Trim

c. Fillet


a. Circle

b. Polygon

c. Ellipse

51. Which tool bar does this icon lie on?

a. Draw tool bar

b. Modify tool bar

16

c. None of these


a. Extend

b. Copy

c. Mirror

53. Offsetting and copying the same circle will give same result

a. True

b. False

54. R.H End Elevation can be used to have L.H End elevation by using_______command

a. Copy command

b. Mirror Command

c. Copy Command

55. Which of the following command can be used to create one or more duplicates of any drawing objects?

a. Mirror Command

b. Copy Command

c. Offset Command

56. Cutting edge must be defined while using______ command

a. Erase Command

b. Trim Command

c. Extend Command

57. What does this AutoCAD symbol represent?

a. Inclined

b. Chamfer

c. Fillet

d. Radius

58. Which command can be started using this icon?

a. Offset

b. Trim

17

c. Extend

59. The ________command is useful for drawing symmetrical objects

a. Offset Command

b. Mirror Command

c. Copy Command

60. What does this AutoCAD icon represent?

a. Arc

b. Spline

c. Polyline

d. Rotate

61. Write the names of the commands these tabs are used for:

LINE COMMAND

ERASE COMMAND

62. Which of the following command you would use to create two concentric circles

a. Mirror

18

b. Copy

c. Offset

63. The corners of rectangular shapes can be rounded by using

a. Chamfer Command

b. Move Command

c. Fillet Command

64. To select a number of objects for modification which method is the quickest one?

a. Picking method

b. Window selection

Practice Questions Graphicsij

Documents

Transcript of Practice Questions Graphicsij