Pqs User Manual Smx-0619-0102 v1.1

5/21/2018 Pqs User Manual Smx-0619-0102 v1.1

1/356

1


2/356

2

Table of Contents

About PQSCADA Enterprise Analysis Software ............................................. 7

PQSCADA Enterprise System ............................................................... 8

PQSCADA Management Studio ............................................................. 9

PQSCADA Server ........................................................................... 10

Installation .................................................................................... 12System Requirements ..................................................................... 13

Software Requirements .................................................................. 14

Installing the New PQSCADA Software ................................................. 15

Install the New Report Management System .......................................... 18

Upgrading the PQSCADA Management Studio ......................................... 22

Uninstall Previous PQSCADA Management Studio Versions ....................... 23

Installing the New PQSCADA Software............................................... 24

Installing the New Report Management System .................................... 28

Upgrading the Server .................................................................. 32

Upgrading Components ................................................................ 34

Recalculating the Parameters ........................................................ 35

Introduction .................................................................................. 38

View Console ............................................................................... 39

Administration Console ................................................................... 49

Tool Bar..................................................................................... 53Getting Started ............................................................................... 54

Starting PQSCADA Management Studio ................................................. 55

Components Creation Wizard ........................................................... 58

Component Details ........................................................................ 62

Commence Data Recording .............................................................. 64

Downloading Recorded Data ............................................................... 66

Log Viewer ................................................................................. 67

Force Connection Attempt ............................................................... 69

Schedule Operation ....................................................................... 70

IP Setup ..................................................................................... 72

Folders Setup .............................................................................. 74

Open Incoming Folder .................................................................... 76

Rescan Device Folders .................................................................... 78

Enable / Disable Data Downloading .................................................... 80

Data Processing .............................................................................. 81

Log Viewer ................................................................................. 84


3/356

3

Force File Parse Attempt ................................................................ 87

Configure Service ......................................................................... 89

Reset PQZIP Files .......................................................................... 93

Folders Setup .............................................................................. 96

Open Incoming Folder .................................................................... 98

Open Bad Files Folder ................................................................... 100

Open Data Backup Folder ............................................................... 102

Enable/Disable Processing .............................................................. 104

Recalculate Data ......................................................................... 106

Swap Phases .............................................................................. 109

Add Factor to Parameters .............................................................. 111

Database ..................................................................................... 113

Log Viewer ................................................................................ 114

Set New Component Database Connection ........................................... 116

Configuration ............................................................................. 118

Re-Index ................................................................................... 122

Delete Log Entries ....................................................................... 123

Database Summary ....................................................................... 124

About PQZIP Upload Manager ............................................................. 126

Using The PQZIP Upload Manager ...................................................... 127

Importing Data ............................................................................ 133

Tasks and Templates ....................................................................... 134

Tasks .......................................................................................... 135

Task Types ................................................................................ 136

Task Triggering ........................................................................... 137

Manually Based Task .................................................................. 138

Schedule Based ........................................................................ 140

Event Based ............................................................................ 142

Add Task ................................................................................... 144

Dynamic Folder Path .................................................................. 146

Add General Export Task ............................................................. 148

PQS Parameter Export Task ................................................................ 155

Adding A Report Task ................................................................. 178

Adding A Fault Location Report Task ..................................................... 187

Adding A FOL Report Task .................................................................. 196

Add An Energy Task ......................................................................... 204Add A Notification Task .................................................................... 209


4/356

4

Add A Device Firmware & Configuration Update Task ................................. 215

Rerun Tasks ............................................................................... 221

Modify Tasks .............................................................................. 223

Delete Tasks .............................................................................. 225

Monitoring ................................................................................. 227

Task Log ................................................................................... 229

Terminate Task Execution .............................................................. 231

Templates .................................................................................... 233

Add A Template .......................................................................... 234

Select Events ........................................................................... 236

Select Parameter ...................................................................... 237

Select Event Trigger .................................................................. 238

Define Property Configurations ..................................................... 239

Modify Template ......................................................................... 241

Delete Template ......................................................................... 242

Preferences .................................................................................. 243

General Preferences ..................................................................... 244

Regional Settings Preferences .......................................................... 246

Security Settings ......................................................................... 247

File Upload Settings ..................................................................... 249

Appearance Preferences ................................................................ 250

Maps .......................................................................................... 251

Map Tools .................................................................................. 252

Notifications Viewer ........................................................................ 253

Disable Pop-Up Notifications ........................................................... 255

Components ................................................................................. 257

Server ...................................................................................... 258

Add A Server ........................................................................... 259

Connect to Server ..................................................................... 261

Delete Server .......................................................................... 263

General Server Configuration ........................................................ 264

Automatic Maintenance .................................................................... 265

Logger ......................................................................................... 267

E-Mail ......................................................................................... 268

SMS/Text ..................................................................................... 269

Report Management ......................................................................... 270Copy Link ..................................................................................... 272


5/356

5

Site - Description ......................................................................... 274

Add Site ................................................................................. 275

Delete Site.............................................................................. 277

Site - Configuration ................................................................... 279

Name Allocation .......................................................................... 280

Image Selection ........................................................................... 281

Node - Description ....................................................................... 282

Add Node ............................................................................... 283

Remove Node .......................................................................... 287

Node - Configuration .................................................................. 289

General ..................................................................................... 290

Device ...................................................................................... 291

Download Schedule ....................................................................... 292

Parameters ................................................................................ 293

Folders ..................................................................................... 298

Database ................................................................................... 299

Device IP ................................................................................ 300

Open In ....................................................................................... 301

Component Functions ................................................................... 302

Collapse ....................................................................................... 303

Expand ........................................................................................ 304

Moving Components ......................................................................... 305

Upgrade Components ....................................................................... 306

Encryption About .......................................................................... 307

Install the SSL Certificate ............................................................... 308

Bind the Certificate ...................................................................... 312

Configure PQSCADA to use SSL ......................................................... 314

Change the Communication Binding ................................................... 316

Security - About the Security Module .................................................... 318

Enable the Security Module Locally ................................................... 321

Define the Primary Security Server .................................................... 323

Set User Login Identification ........................................................... 325

User Accounts - About User Accounts ................................................. 326

Create & Add New Users ............................................................. 332

Change User Accounts ................................................................ 335

Tool Tips ..................................................................................... 338Component Tool Tips .................................................................... 339


6/356

6

Device Tool Tips .......................................................................... 340

Download Status Tool Tip ............................................................... 341

Data Processing Tool Tips ............................................................... 342

Compliance Tool Tips .................................................................... 343

Database Tool Tips ....................................................................... 344

Video Demonstrations ...................................................................... 345

Troubleshooting ............................................................................. 347

Log Viewer ................................................................................ 355


7/356

7

About PQSCADA Enterprise Analysis Software

Innovative PQSCADA Enterprise Analysis software enables the operator to view, control,

analyze, and monitor multiple measurement devices simultaneously. Data is accurately

time-synchronized, within and across,Sites.The PQSCADA application is made up of the

following:

PQSCADA Enterprise System

PQSCADA Management Studio

PQSCADA Server


8/356

8


Note: This drawing depicts the master modules initiating the

communication

The PQSCADA Enterprise System is installed on a personal computer providing unparalleled

data monitoring and analysis functionality for all BLACKBOX devices. (For software

installation instructions, please refer to Installing the PQSCADA Software).

PQSCADA Management Studio:The user interface (GUI) that is used to configure

the PQSCADA Server as well as check status of the components (See PQSCADA

Management Studio).

PQSCADA Server: A windows serviced based application that runs in the

background even when you are not logged in (See PQSCADA Server).

Client Application:Elspec Power Quality Investigator.

MS SQL Storage: database engine: An SQL Database engine used by the PQSCADA

Server to store and process the data.

SEE ALSO



PQSCADA Server


9/356

9


The PQSCADA Management Studio is a Graphic User Interface console used tocommunicate with the PQSCADA Server. The PQSCADA Server is a windows service.

The PQSCADA Installation Procedure allows you to install both the PQSCADAManagement Studio and the PQSCADA Server (PQS service). In order to stop and/orstart the PQS service, you may use the Graphical User Interface (GUI) as below orby accessing the Services through windows configuration.

PQSCADA Management Studio PQS Service

SEE ALSO



PQSCADA Server


10/356

10

PQSCADA Server

Note: This drawing depicts the flow of data

The PQSCADA server is the heart of the BLACKBOX data management and analysis system.

The main functionality of the PQSCADA server is shown in the figure above and further

described below with corresponding numbered marks:

1. Download: PQSCADA collects all waveform data that has been continuously

recorded in the compressed PQZIP format.

2. Process: The data is processed and organized for quick access and storage. A wide

range of electrical parameters are then calculated based on the raw PQZIP data.

The reorganized PQZIP data, and the calculated parameters with statistics

included, are stored and available on the network for later retrieval.


11/356

11

3. Deliver: All the electrical information, including event flagging & notificationsare

delivered over a number of communication gateways. This feature includes report

exportsin various compatible formats such as COMTRADE, PQDIF, CSV, RTF, HTML,

PDF, etc.

4. Visualize: Detailed data can be easily analyzed by any number of clients at any

location. The Investigator Software provides an immediate, comprehensive and

understandable picture of everything that happened within the network.

SEE ALSO





12/356

12

\\

Installation

The PQSCADA software is quite simple to install. Of course before anyinstallation can be performed, you must verify that Minimum SystemRequirementsandSoftware Requirementsare met.

There are two installation options:

New Installation: Installing the PQSCADA Softwareas a new installation

Upgrade: Upgrading. an existing version of PQSCADA


13/356

13

System Requirements

Regardless of OS:

No. of units CPU RAM Storage

1-3

Later Model Dual

Core 2GB

20-75GB per unit per year,

depending on default Cycle By

Cycle parameter selection3-5

Later Model Quad

Core4GB

>5 Contact Support


14/356

14

Software Requirements

In order to successfully install PQSCADA, you must first install the followingsoftware prerequisites on your system:

FOR WINDOWS 7 SP1/SERVER 2008 R2 SP1:

Microsoft .Net Framework 4.0 - A Universal platform developed by Microsoft

that provides identical functions for a variety of languages (C#, Visual Basic,

Java). It is also designed to facilitate development of web applications.

(Enable communication between clients and servers).

FOR WINDOWS VISTA SP2 / SERVER 2008 SP2 / XP SP3 / SERVER 2003SP2:

All of the above, including:

Microsoft .Net Framework 3.5 SP1 - A Universal platform developed by

Microsoft that provides identical functions for a variety of languages (C#,

Visual Basic, Java). It is also designed to facilitate development of web

applications. (Enable communication between clients and servers).

Windows PowerShell 2.0 - Microsoft's task automation framework, consisting

of a command-line shell and associated scripting language built on top of,

and integrated with the .NET Framework. PowerShell provides full access to

COM and WMI, enabling administrators to perform administrative tasks on

both local and remote Windows systems.

Microsoft Windows Installer 4.5 - Application installation and configuration

service for Windows.


15/356

15

Installing the New PQSCADA Software

The following procedure describes a new installation of the PQSCADA softwareapplication. Prior to Installing the new PQSCADA Software, ensure that yoursystem meet all the Software Requirements. An automated installation isavailable on the BLACKBOX Disc (enclosed with every unit). For upgrading froma previous version, please refer to Upgrading the PQSCADA Software.

The applications setup wizard will guide you through the installation process:

1. At the download location on your hard drive select the PQSCADA icon:

2. The Welcome Screenof the installation guide will now open:

3. Select the button to commence the installation process

4. Read & accept the license agreement at I Agree & select thebutton:


16/356

16

5. The PQSCADA Components screen will now open. (Elspec recommends

selecting both components). Select the button:

6. The wizard will now request the location where you would like to install theapplication. It is recommended to include it on your Hard Drive under an

Elspec folder. Either Browse / Type the Location, select the AvailabilityOption& select the button:


17/356

17

7. Select the followed by the button, to complete theinstallation:

PROCEED TO THE NEXT STEP: Install the New Reports ManagementSystem.


18/356

18

Install the New Report Management System

With PQSCADA V4.2.2.2 the PQS Server & Management Studio can beinstalled independently on two different computers. This increases theflexibility & accessibility of the PQSCADA 4.2. As part of this developmentthe Report System is installed independently from the PQSCADA. This allows

the user to effectively manage the reporting system of the entire network.Users simply select & install reports of relevance from any location. TheReports are installed separately from the PQSCADA Management Studio onElspec's Website. In addition an automated installation is available on theBLACKBOX Disc (enclosed with every unit). After you have installed the newPQSCADA 4.2, you will need to install the new Reports. The followingprocedure describes the installation process. The installed reports of yourchoosing can be viewed on theServer's Configuration.

TYPES OF REPORTS:

Fault Location Report

FOL Compliance Report

Chinese Power Quality Report

GOST Report

NRS 048:2 2007 Report

Event Based Compliance Report

Power Quality Report (Prodist)
http://www.elspec-ltd.com/category/PQSCADA_Releasehttp://www.elspec-ltd.com/category/PQSCADA_Releasehttp://textpopup%28this%29/http://textpopup%28this%29/http://www.elspec-ltd.com/category/PQSCADA_Release


19/356

19

INSTALL THE REPORTS VIA THE BLACKBOX DISC:

In Step 4of the Installation Processsimply select the report of your choosing

that you wish to install:

The installation process will automatically run. The installed reports can be

viewed on the Report Management's tab within theServer's Configuration.

INSTALL THE REPORTS FROM ELSPEC'S WEBSITE:

After you have downloaded theReport Module from Elspec's Website,selectthe Type of Reportyou wish to install:

Run the "exe" option in the folder:
http://textpopup%28this%29/http://textpopup%28this%29/http://www.elspec-ltd.com/category/PQSCADA_Reportshttp://www.elspec-ltd.com/category/PQSCADA_Reportshttp://www.elspec-ltd.com/category/PQSCADA_Reportshttp://www.elspec-ltd.com/category/PQSCADA_Reportshttp://textpopup%28this%29/http://textpopup%28this%29/


20/356

20

The Welcome Screen of the installation guide will now open:

Select the button to commence the installation process

Read & accept the license agreement at I Agree & select the button:

The wizard will now request the location where you would like to install the Report &you can choose either option:

Default- Hard Drive under an Elspec folder

Preferred Location - As the Reports is independent installations youll need to

configure theReport Path:

Select the button:

Select the twice followed by the button, to complete theinstallation:


21/356

21

The installed reports can be viewed on the Report Management's tab within the

Server's Configuration.


22/356

22

Upgrading the PQSCADA Management Studio

The upgrade procedure consists of the following steps in order:

1. Uninstalling PQSCADA Management Studio

2. Installing the new PQSCADA Management Studio

3.

Installing the New Reports Management System

4. Upgrading the Server

5. Upgrading Components

In most cases it is unnecessary to Enable downloading or Enable Data Processing of an

imported node. The node will continue to function in the same state as it was left from

the previous version of PQSCADA.

6.

Re-calculating Parameters(optional)


23/356

23

Uninstall Previous PQSCADA Management Studio Versions

Uninstalling the existing version of the PQSCADA is the first step to upgrade the software.

1. Access your Start Menu,

2. Select: Elspec PQSCADA Uninstall

PROCEED TO THE NEXT STEP: Installing the PQSCADA Software.


24/356

24

Installing the New PQSCADA Software

After you have Uninstalled the previous PQSCADA version, you will need to install the new

PQSCADA version from anew. The following procedure describes the PQSCADA installation

process. An automated installation is available on the BLACKBOX Disc (enclosed with every

unit).

NOTE NOTE NOTE

The PQSCADA 4.2 & later versions, support a new Report System that is installed

independently after you have installed the new PQSCADA V4.2.2.2. All tasks related to

report tasks, therefore needs to be reconfigured from anew. Ensure that you backup

your Database prior to installing the new version in order not to lose previous data.

The applications setup wizard will guide you through the installation process:

1. At the download location on your hard drive select the PQSCADA Icon:

2. The Welcome Screenof the installation guide will now open:


25/356

25

3. Select the button to commence the installation process

4. Read & accept the license agreement at I Agree & select the button:

5. The PQSCADA Components screen will now open. Elspec recommends selecting both

components. Select the button:


26/356

26

6. The wizard will now request the location where you would like to install the

application. It is recommended to include it on your Hard Drive under an Elspec folder.

Either Browse / Type the Location, select the Availability option & select the

button:

7. Select the followed by the button, to complete the

installation:


27/356

27

PROCEED TO THE NEXT STEP: Install the New Reports Management System.


28/356

28

Installing the New Report Management System

With PQSCADA V4.2.2.2 the PQS Server & Management Studio can be installed

independently on two different computers. This increases the flexibility &

accessibility of the PQSCADA 4.2. As part of this development the Report System is

installed independently from the PQSCADA. This allows the user to effectively

manage the reporting system of the entire network. Users simply select & install

reports of relevance from any location. The Reports are installed separately from

the PQSCADA Management Studio on Elspec's Website. In addition an automated

installation is available on the BLACKBOX Disc (enclosed with every unit). After you

have installed the new PQSCADA 4.2, you will need to install the new Reports. The

following procedure describes the installation process. The installed reports of your

choosing can be viewed on theServer's Configuration.

NOTE NOTE NOTE

Prior to installing the new PQSCADA V4.2.2.2 & the new Report Management System all

tasks related to report tasks, needs to be reconfigured from anew. Ensure that you

backup your Database prior to installing the new PQSCADA version in order not to lose

previous data.

The Report Management supports:

TYPES OF REPORTS:

Fault Location Report

FOL Compliance Report

Chinese Power Quality Report

GOST Report

NRS 048:2 2007 Report

Event Based Compliance Report

Power Quality Report (Prodist)
http://www.elspec-ltd.com/category/PQSCADA_Releasehttp://www.elspec-ltd.com/category/PQSCADA_Releasehttp://textpopup%28this%29/http://textpopup%28this%29/http://www.elspec-ltd.com/category/PQSCADA_Release


29/356

29

INSTALL THE REPORTS VIA THE BLACKBOX DISC:

In Step 7of the Upgrading Processsimply select the report of your choosing

that you wish to install:

The installation process will automatically run. The installed reports can be viewed

on the Report Management's tab within theServer's Configuration.

INSTALL THE REPORTS FROM ELSPEC'S WEBSITE:

After you have downloaded theReport Module from Elspec's Website,select

the Type of Reportyou wish to install:

Run the "exe" option in the folder:
http://textpopup%28this%29/http://www.elspec-ltd.com/category/PQSCADA_Reportshttp://www.elspec-ltd.com/category/PQSCADA_Reportshttp://www.elspec-ltd.com/category/PQSCADA_Reportshttp://www.elspec-ltd.com/category/PQSCADA_Reportshttp://textpopup%28this%29/


30/356

30

The Welcome Screen of the installation guide will now open:

Select the button to commence the installation process

Read & accept the license agreement at I Agree & select the button:

The wizard will now request the location where you would like to install the Report &you can choose either option:

Default- Hard Drive under an Elspec folder

Preferred Location - As the Reports is independent installations youll need to

configure theReport Path:

Select the button:

Select the twice followed by the button, to complete theinstallation:


31/356

31

The installed reports can be viewed on the Report Management's tab within the

Server's Configuration.

PROCEED TO THE NEXT STEP: Upgrading the Server.


32/356

32

Upgrading the Server

Double click the PQSCADA icon on your desktop:

The Main menu appears with the existing Server offline. (In order to add a newserver, please refer to Getting Started) Right click at Server is offline, then selectUpgrade / Upgrade All:

PQS Serverhas been updated and brought online with a Site and Node attachedthat may require an upgrade:


33/356

33

PROCEED TO THE NEXT STEP: Upgrading Components


34/356

34

Upgrading Components

We recommend that you upgrade all sites and nodes together for each server; however

you may choose to upgrade them individually as well. As shown below Elspec Site & Elspec

Node appears but is not yet upgraded or active.

To upgrade all sites and nodes for a server, right click the server (Test server in ourexample), then select Upgrade / Upgrade All:

The Site (Elspec Site) and Node (Elspec Node) have been upgraded and nowappear under PQS Server:

PROCEED TO THE NEXT STEP: Recalculating Parameters(Optional)


35/356

35

Recalculating the Parameters

This optional step allows you to recalculate any parameter(s) for a stipulated

period. For example apart from IEC 61000-4-30 Class A parameters that has

been included for PQSCADA 4.0 & later versions, the latest version PQSCADA

4.2 includes Class A parameters for Current previously only calculated forVoltage. You may therefore need to recalculate these parameters.

NOTE NOTE NOTE

We recommend that you perform this procedure only when necessary,

since it can take up a considerable amount of time (approximately two

weeks to calculate one years worth of data). Prior to following this

procedure configure the necessaryParameters in Node Configuration.

In addition refer to the table below as a further guide:

Upgrading from Version to

Version

Changed/Added Parameters*

4.1 > 4.2

New Additions - Cycle by Cycle:

In Waveforms -Crest Factor

In Statistics - Frequency Cycle by

Cycle

New Additions - Class A:

In Inter-Harmonics- Phasors

4.0 > 4.1 Improvement in the Cycle-by-cycle Frequency

DC Included in all Parameters

Power Factor included

3.3.0.13 > 4.0 IEC 61000-4-30 Class A Parameters Included

DC Included in most Parameters

Unbalance parameters

3.2.0.40 > 3.3.0.13 None


36/356

36

3.1.4.5->3.2.0.40 Unbalance parameters

Idc harmonic

3.1.1.0->3.1.4.5 All the parameters in single phase systems

Unbalance parameters

Idc

* All other parameters will have the same values after recalculation

PROCEDURE TO RECALCULATE THE PARAMETERS:

1. From the PQSCADA main menu, right click the desired Node in the Data

Processing column:

2. Select Recalculate data. The Recalculate Node Data screen appears:
http://textpopup%28this%29/http://textpopup%28this%29/


37/356

37

3. Set the desired start and end time.

4. Click .


38/356

38

Introduction

The PQSCADA user interface screen is comprised of three distinct sections; the

Tool Bar,Status Bar, and the Main Viewing Area. TheTool Barcontains certain

specific functional icons specific to the active console. Two different viewing

Consoles are available; View Console and Administration Console. The mainviewing area contains all of theSites/Nodes,Tasks,Templates,Map&PQZIP

Upload Managerfor the grid.

SEE ALSO:

View Console

Administration Console

Tool Bar

TUTORIAL DEMONSTRATION:

We have created the following collection of Flash Video Tutorial

Demonstration(s) that may be opened with Internet Explorer or any flash

player available on your system.

For A Video Demonstration of thePQSCADA User Interface.
http://textpopup%28this%29/http://textpopup%28this%29/http://www.elspec-ltd.com/category/Instructional_Videoshttp://www.elspec-ltd.com/category/Instructional_Videoshttp://www.elspec-ltd.com/category/Instructional_Videoshttp://www.elspec-ltd.com/category/Instructional_Videoshttp://textpopup%28this%29/http://textpopup%28this%29/


39/356

39

View Console

The View mode is divided into two sections - the Top Section & Status Bar.By

selecting the buttons on the Top Sectionyou either access directly the Sites/

Nodes,Tasks,Templates,Map&PQZIP Upload Manager:

TOP SECTION ACCESS:

Refresh:To reset the Sites and Nodesif for some reason connection is lost.

NODES/SITES:

This selection allows you to view and modify only the activeSites&Nodes:

TASKS:

This selection allows you to view and modify active Tasks/Templates

associated with theSites:
http://textpopup%28this%29/http://textpopup%28this%29/http://textpopup%28this%29/http://textpopup%28this%29/


40/356

40

MAP:

A feature which enables you to visually manage the locations of nodes

contained within a site by dragging the nodes within the Site MAP and

placing them at relevant locations onto a site illustration or image. For

more onMaps:


41/356

41

PQZIP UPLOAD MANAGER:

PQSCADA V4.2.2.2 & later versions allows for the PQS Server & Management

Studio to be installed on two different computers. With the PQSCADA V 4.2

you can now upload PQZIP files from a different folder location other than

the incoming folder to any selected Node. Meaning PQZIP files located on

the PQS Server's incoming folder / PQZIP files recorded by other BLACKBOX

devices can now be uploaded in this manner. This feature allows you to

manage & control the uploading process of PQZIP compressed files see

PQZIP Upload Manager:

STATUS BAR:

The Status Baris divided into 5 columns & functions can be performed only for

theComponents:

By selecting any component Server, Site or Node you can perform various

functions within each column by a simple right-click of your mouse:


42/356

42

STATUS BAR FUNCTIONS:

COMPONENTS COLUMN:

In this column you may view all the Components including Tool Tips on

moving your mouse over the component. You may also Configure the

Component directly, by double-clicking on your selection. You may also

perform the following actions:

For theServer:You canExpand,Collapse,Refresh (resets in the event

the connection is lost), Copy a Link,Connect,Disconnect,Change the

Communication Binding,Login,Logout,Add a Site,View the Log, access

the User Manager (only with Security Enabled), View Notifications,Configure the Server&Delete the Server.

For a Site:You can Expand,Collapse,Refresh your view, Add a Node,

Add a Site, View the Log, View Notifications, Configure the Site &

Delete the Site.

For a Node: You may Refresh (resets in the event the connection is

lost), View the Log,Configure the Node&Delete the Node.


43/356

43

NOTE NOTE NOTE

Login & Logout will feature only when the Security Module has been

enabled. Please seeEncryption& theSecurity Module.

DEVICE IP COLUMN:

This column provides access to a specificNodesDevice IP settings. You may

perform the following actions:

Open the Device in the Web Browser

Open the Device in the FTP

Access the Device IP Setup, where you mayConfigure the Device

DOWNLOADING COLUMN:

This column provides control over the downloading process of PQZIP files

from the BLACKBOX unit into the PQSCADA Server. The PQSCADA Server

system is responsible for collecting continuous data (PQ Zip files) from a

connected device. When the device is connected (wired or wireless), the

PQSCADA server checks for any new data availability using an FTP

communication Protocol. By default the downloading process is disabled, in

order to commence the download select the applicable Node right click

select Enable. You may also perform the following actions:

Refresh: Will update you on the Data Downloading status for the

Node(s)

Log Viewer: The Log Viewer enables you to see specific information

related to log entries with varying levels of importance

Force Connection Attempt (only relevant after the device is enabled):

Force Connection Attempt allows you to manually download files


44/356

44

from the device to PQSCADA without waiting for the next automatic

download attempt

Schedule Operation: Allows you to configure & set a schedule for

downloads

IP Setup:Provides access to configure thedevice's IP settings

Folders Setup: This action provides direct access to set the Nodes

incoming, backup & bad folder(s) size limits

Open Incoming Folder: With this action it is possible to view all

imported PQZIP files that are waiting to be processed

Rescan Device Folders:This action resets the PQZIP folder cache &

generate a full folder scan on this device

DATA PROCESSING COLUMN:

In this column you may perform various actions directly related to the PQZIP

data processing engine. Actions that you may perform within this column:

Refresh:Will update you on the Data Processing status for the Node(s)



Force File Parse Attempt: Force Connection Attempt allows you to

manually download files from the device to PQSCADA without waiting

for the next automatic download attempt

Configure Service: This option will allow you to directly Configure

Parameters for the Node, without having to go through Node

Configuration

Reset PQZIP files: This function allows you to select and sort the

imported PQZIP files & to re-download the processed files

Folders Setup: This action provides direct access to set the Nodesincoming, backup & bad folder(s) size limits


45/356

45

Open Incoming Folder: With this action it is possible to view all

imported PQZIP files that are waiting to be processed. You may also

choose to manually move files from other folders to this folder in order

for the PQSCADA to process the data

Open "Bad Files" Folder: With this action it is possible to view all

imported PQZIP files that are contained within the Bad Files Folder

Open Data Backup Folder: With this action it is possible to view all

imported PQZIP files that are contained within the Backup Folder

Recalculate Data: This action allows you to recalculate the desired

parameters. It is recommended that you perform this procedure only

when necessary as it may take a considerable amount of time

(approximately two weeks to calculate one years worth of data)

En/Disable Processing: By default all imported or created nodes are

disabled to process data & therefore needs to enabled

Swap Phases: This operation allows you to swap data between two

different voltage phases and neutral, as well as, current phases

Add Factor Parameters:This option allows you to correct & recalculate

all the parameters, in the event of an incorrect & invalid setup (i.e.

Clamp Setup / PT Ratio correction / CT Ratio correction / Current

Polarity)

COMPLIANCE STATUS COLUMN:

This new column has been added in order to detail the relevant compliance

status as per the device's configuration (via Elspec's Web Interface). The

column purely provides information regarding the overall compliance status

of the last week at a resolution of 2 hours. This is a very useful tool in

reviewing the overall compliance status for a large number of Nodes.


46/356

46

Indicators:

Compliance Type: EN50160/ User Defined / NVE-PQ Norway etc.

Date:Date of last recorded compliance

Time:Time of last recorded compliance

Status (3 States):

Retrieving: Insufficient data present to indicate the status

Failed:Overall compliance failed

[OK]: Overall compliance succeeded

NOTE NOTE NOTE

Don't forget to use theTooltip- it will be most helpful in providing you withdetailed information regarding the compliance parameter calculations. Inthe compliance column simply select & right-click on the applicable Node toretrieve the information:


47/356

47

DATABASE COLUMN:

By right clicking on a Server, SiteorNode in the Database Columnit

is possible to access the following configuration tools directly related to

theDatabase:

Refresh: Will update you on the Database status for the Node(s)



Set New Database Connection: Allows you to change the server

database and/or individual attributes

Configuration: Will provide you with direct access to configuration

settings related to the database for either the Server (Automatic

Maintenance)&/orNode(Database)

Re-Index: Periodic maintenance operation in order to keep the

PQSCADA application running at an optimal speed. This is especially

true as the size of the database increases over time

Delete Log Entries:Allows you delete entries according to Log Type and

Start/End Date. This action may be carried out for theServeronly

Delete Data:This operation removes all binary data in the requested

time range from only for theNodes database, along with, all relevant

summaries

Database Summary: A newly added feature the Database Summary

provides a detailed summary on any component be that Server, Site&

/Node

SEE ALSO:

Introduction to the PQSCADA Interface


Tool Bar


48/356

48





For A Video Demonstration of thePQSCADA User Interface.
http://textpopup%28this%29/http://www.elspec-ltd.com/category/Instructional_Videoshttp://www.elspec-ltd.com/category/Instructional_Videoshttp://www.elspec-ltd.com/category/Instructional_Videoshttp://www.elspec-ltd.com/category/Instructional_Videoshttp://textpopup%28this%29/


49/356

49


The Administration console provides functional icons. From the View Console the

layout of the administration console changes according the selected View. The

three views are Sites/Nodes, Tasks, & Maps. For your convenience the newly

added PQZIP Upload Manager remains in both consoles, in order to monitor the

status & manage the data upload management at any time. Views:

Consoles under View Respective Administration Console Views

NODES/SITES:

This selection allows you to view the administration (Server/Site/Node) functions

for the selected Server/Site/Node:

Refresh:To reset theServer/Site/Nodeif for some reason connection is lost

Locked:To allow/disallow moving ofSite/Nodeby dragging and dropping.

Connect to Server:Connect to a Server

Delete Server Database: ToDelete Server including Database

Add Node:Add aNode(s)to aSite(Adding a Node)

Delete Node:Remove aNodefrom a Site (Deleting a Node)

Add Site:Add aSite(Adding a Site)

Delete Site:Remove aSite(Deleting a Site)


50/356

50

Wizard:Wizard for creating Components (Component Creation Wizard)

PQZIP Upload Manager: Manage & control the upload of PQZIP file uploads

(PQZIP Upload Manager)

PQS Service:To start and stop the PQS Service (PQSCADA Management Studio)

Preferences:Global user defined settings for the software (Preferences)

Disable Notifications: Select Pop-up Notifications from a list that you wish to

disable (please refer toDisable Pop-Up Notifications)

TASKS/TEMPLATES:

Refresh:To reset the Sites and Nodes if for some reason connection is lost

Locked/Unlocked:To allow/disallow moving of Sites/Nodesby dragging and

dropping

Add Task:Add a Task(s) to a Site (Adding a Task)

Delete Task:Remove a Task from a Site (Deleting a Task)

Add Template:Adding a Template (Adding a Template)

Delete Template:Deleting a Template (Deleting a Template)

PQS Service: To start and stop the PQS Service (Please refer to PQSCADA

Management Studio)

Preferences:Global user defined settings for the software (please refer to

Preferences)

Disable Notifications: Select Pop-up Notifications from a list that you wish to

disable (please refer toDisable Pop-Up Notifications)


51/356

51

MAPS:

Map Tools:See Map Tools

Preferences:See Preferences

PQZIP UPLOAD MANAGER:

With PQSCADA V4.2.2.2 the PQS Server & Management Studio can be installed

independently on two different computers. This feature allows you to upload

PQZIP files recorded by any BLACKBOX device, to any Remote Server. Manage& control the uploading process of PQZIP compressed files. This feature allows

you to manage & control the uploading process of PQZIP compressed files - see

PQZIP Upload Manager:

SEE ALSO:


View Console

Tool Bar
http://textpopup%28this%29/http://textpopup%28this%29/http://textpopup%28this%29/http://textpopup%28this%29/http://textpopup%28this%29/http://textpopup%28this%29/


52/356

52





For A Video Demonstration of thePQSCADA User Interface
http://textpopup%28this%29/http://www.elspec-ltd.com/category/Instructional_Videoshttp://www.elspec-ltd.com/category/Instructional_Videoshttp://www.elspec-ltd.com/category/Instructional_Videoshttp://www.elspec-ltd.com/category/Instructional_Videoshttp://textpopup%28this%29/


53/356

53

Tool Bar

The tool bar contains icons that represent theComponents,Tasks,Templates,

&Mapsthat are used to build the infrastructure as well as manage theServer,

Sites & Nodes.The selection of available icons is dependent on the viewing

console selected.

In the View Console, it is possible to view all current Server/Sites/Nodes,

Tasks,& Maps.The opening default screen is the Sites/Nodesselection in the

View Console.

In theAdministration Console,it is possible to select functions associated with

any of the aforementioned icons.

SEE ALSO:


View Console



We have created the following collection of Flash Video Tutorial Demonstration(s) that

may be opened with Internet Explorer or any flash player available on your system.

For A Video Demonstration of thePQSCADA User Interface
http://textpopup%28this%29/http://textpopup%28this%29/http://www.elspec-ltd.com/category/Instructional_Videoshttp://www.elspec-ltd.com/category/Instructional_Videoshttp://www.elspec-ltd.com/category/Instructional_Videoshttp://www.elspec-ltd.com/category/Instructional_Videoshttp://textpopup%28this%29/http://textpopup%28this%29/


54/356

54

Getting Started

This section introduces you to the most basic critical functions of the PQSCADA

Management software. It is assumed this is a new installation with no existing

Servers, Sites or Nodes, to be upgraded (for upgrading see Upgrading

Components). Getting Started guides you through a step-by-step process that

includes the following: Starting PQSCADA Management Studio

Creating Components using the Components Creation Wizard

Fill in the Component Details

Commencing Data Recording



Demonstration(s) that may be opened with Internet Explorer or any flashplayer available on your system.

For a Tutorial Video Demonstration onPQSCADA Getting Startedthat

provides a step-by-step tutorial that will guide you through the

process of setting up your firstServer,Site,andNode.
http://www.elspec-ltd.com/category/Instructional_Videoshttp://www.elspec-ltd.com/category/Instructional_Videoshttp://www.elspec-ltd.com/category/Instructional_Videoshttp://www.elspec-ltd.com/category/Instructional_Videos


55/356

55

Starting PQSCADA Management Studio

To start the PQSCADA Management Studio -

Click the icon on the desktop or select Start All

Programs Elspec PQSCADA PQSCADA Management Studio:

The PQSCADA Management Studio window appears:


56/356

56

Select the Administration Console. Either right click select Connect to

Server or select Connect to Servertab:

The Add Serverdialog box appears:

For the URL Select & Add:

HTTP - Is the default method of communicating with the server. The

software uses HTTP port 80 as the default port to communicate with the

Node.

HTTPS - Is the combination of the Hypertext Transfer Protocol (outlined

above) with the SSL protocol to provide encrypted communication and

secure identification of a network web server. SeeEncryption.

net.pipe - Improves the connection in case that the server is a local

connection. This option will speed up the http connection.

Precise URL addressof the Server. In this example the Url address for the

HTTP connection is localhost/PQS.

Select button. Should the test for the connection be successful, the message will appear:


57/356

57

Select & to connect to the server.

NOTE NOTE NOTE

Ensure that all the prerequisites Software Programs are installedprior to connecting to the server.

PROCEED TO THE NEXT STEP: COMPONENTS CREATION WIZARD (that willguide you through a step by step procedure to connect to additional servers, &to add site(s) & node(s)).

SEE ALSO:

Components Creation Wizard

Component Details




Demonstration(s) that may be opened with Internet Explorer or any flash player

available on your system.

For a Tutorial Video Demonstration on PQSCADA Getting Started that provides a

step-by-step tutorial that will guide you through the process of setting up your first

Server,Site,andNode.
http://www.elspec-ltd.com/category/Instructional_Videoshttp://www.elspec-ltd.com/category/Instructional_Videoshttp://www.elspec-ltd.com/category/Instructional_Videos


58/356

58


This wizard will act as a guide when either connecting to additional Servers, or

creatingSite(s)orNode(s).

HOW TO CONNECT TO A SERVER, OR TO CONNECT TO AN ADDITIONAL

SERVER: Either select the Connect to Server Button or open the wizard by selecting the

Wizard Button:

The Components Creation Wizard :

Select Database Engine: Identifies the database engine as an SQL type server.


59/356

59

SQL Express Install Button: Launches an automatic installation of the SQL server

where most parameters are pre-configured. We recommend using SQL Express only for

evaluation purposes. (SeeSoftware Requirements).

Browser button: The browser button allows you to search for an available database

servers.

Engine Name: The name assigned to the server database engine.

User Name: The name of the user as defined for the database server (For SQL Express

installed from the BLACKBOX CD, the user name is sa).

Password: User Defined (For SQL Express installed from the BLACKBOX CD, the

password is PQSpqs12345).

Test Button:Will test & validate the connection in order to ensure that the details

including the Password for the Database Engine are correct.

Set Default Credentials: Will set Server Name, Username & Password to factory

defaults.

Save Settings:If you checked this box in one of theAdd Server,Add Site,orAdd Node

dialog boxes, then all attributes are automatically pre-filled; otherwise they will

remain blank.

NOTE NOTE NOTE

Ensure that all the prerequisites Software Programs are installed

prior to installing SQL Express

You need to select the button, in order to run the full

validation process. This is especially applicable in the event that

you may have entered an incorrect password. As such the

validation process will be incomplete & the PQSCADA system will

prohibit you from performing certain actions.


60/356

60

HOW TO CREATE COMPONENTS:

1. Click the Browser button next to the Server name. The Select Database

Server window appears.

2. Select Local Servers tab. (You may access remote databases through the

Network Servers tab).

3. Double click the desired database or highlight and click Select.

4. Enter your User nameand Password.

5. Click Testto verify the connection.

6. Select Save Settings. (Recommended not mandatory; this will set the

selected database engine as default and will eliminate the need to reset the

database engine at the next attempt of adding sites and nodes).

7.

Click Nextto continue. TheComponents Details Windowappears.

SEE ALSO:


Component Details



61/356

61









62/356

62

Component Details

The Components Details window allows you to enter information about the site and node.

Specifically, this is where the site (Elspec Site 1) and node name (Elspec Node 1) are

assigned and the desired node IP (100.100.100.100) is selected from the available

devices on the network.

1. Enter a namefor the server and site. (user defined)

2. Select a device by clicking theDevice IP Browserbutton.

3. The Select Devicewindow appears. The automatic device discovery is

activated now and should find all devices on the local LAN if UDPbroadcasting is allowed. You may also select the Reload button in this

window in order to rescan the devices should some of the devices be

missing from the list.

4. Double click the selected device(s).

5. The Nameappears in the window.

6. Set the local time to GMT Offset.

7. Click to complete.

8. The Creation Progress window appears:


63/356

63

10.The Server with the Site and Node can be viewed in the main window.

PROCEED TO THE NEXT STEP:COMMENCE DATA RECORDING

SEE ALSO:












64/356

64

Commence Data Recording

Double click the node in the Data Processing Column.

TheNode Configuration / Parameterswindow appears:

Select the desired Calculation Groups, click .

To commence data recording, right click the Node in the Data Download

Column, then select Enable.

The node is now downloading data from the device.

SEE ALSO:



Component Details

Configure Parameters


65/356

65









66/356

66

Downloading Recorded Data

This column provides control over the downloading process of PQZIP files from the

BLACKBOX unit into the PQSCADA Server. The PQSCADA Server is responsible for

collecting continuous data (PQZIP files) from a connected device. When the device

is connected (wired or wireless), the PQSCADA server checks for any new data

availability using an FTP communication Protocol. By default the downloading

process is disabled, in order to commence the download it needs to be Enabled.

By double-clicking either theServerorNodewithin this column, will navigate you

directly to the following configuration options: General Configuration for the

server &Download Schedulefor the node. On mouse-overTooltipswill appear for

eachComponent. For details, see PQSCADA Server.

By right clicking anywhere in the Downloading Columnfor the selected device,

you may access the following:.

Refresh:Will update you on the Data Downloading status for the Node(s).

Log Viewer

Force Connection Attempt (only relevant after the device is enabled)

Schedule Operation

IP Setup

Folders Setup

Open Incoming Folder

Rescan Device Folders (only relevant after the device is enabled)

Enable/Disable Data Downloading


67/356

67

Log Viewer

The Log Viewer enables you to see specific information related to log entries &

in this specific case entries related to downloading process of PQZIP files.

Right click anywhere in the Downloading Column select Log Viewer:

Use the following Filters to narrow-down your view:

Log Type: (Debug, Info, Warning, Error, Critical)

Debug: By default this option is disabled & it is used only by

an Elspec Software Technician.

Info: Will include general information on actions taken in

PQSCADA. In addition, it will also include Warnings, Error &Critical entries.

Warning: Will include any malfunctions that the PQSCADA will

resolve by itself. The log will also include any Errors & Critical

entries.

Error: Includes malfunctions that the PQSCADA was unable to

resolve. For example failed Tasks due to an incorrect E-Mail

address. See Troubleshooting. The log will also include any

Critical entries. Critical: Contact Elspec or your local representative.


68/356

68

# of Last Entries: This function will enable you to extract only the

desired number of Last Entries from the vast amount of all the

recorded data, allowing you to focus on the latest relevant data.

Start / End Date & Time: Select Start Date & Time option, should

you wish to change your search to include entries from a different

date & time.

Entries in the Log Viewer from this column are related todownloading process of PQZIP files & will initially automatically

display these entries. Should you wish, you may Include any other

Keywords into your search:

SEE ALSO:

Force Connection Attempt

Schedule Operation

IP Setup Folders Setup


Rescan Device Folders


69/356

69


Force Connection Attempt allows you to manually download files from the device

to PQSCADA without waiting for the next automatic download attempt. The

frequency and timing for downloading is configured in the Download Schedule

Configuration.

SEE ALSO:

Log Viewer

Schedule Operation IP Setup

Folders Setup




70/356

70

\

Schedule Operation

To configure & set a schedule for downloads, selectSchedule Operation by

right clicking the Nodein the Downloading Column:

This will open the Download Schedule tab directly in the Node

Configuration:

Configure the settings by entering:


71/356

71

Periodic Time to Get File: This is a user defined setting to determine the

interval of time to retrieve the PQZIP file(s) from the device. If multiple

files exist, this setting is not relevant and there will be no delay.

Download Schedule: The specific days and times to perform the file

retrieval.

Limit Download Time Range: Specifies which files are downloaded that

meets a specific date criteria. Enabling this parameter will exclude filesthat do not fall in the specified time range.

File Download Mode: This is a factory setting that should not be changed.

Select to set the Download Schedule.

SEE ALSO:

About Downloading Recorded Data


Log Viewer

IP Setup

Folders Setup





72/356

72

IP Setup

To configure device, select IP Setup by right clicking the Node in the

Downloading Column:

This will open the Devicetab directly in theNode Configurationwindow:

Enter:

IP Address: Enter the IP address of the device or use the search window

browser.


73/356

73

User Name:Each device is shipped with a default user name (ftpuser) as

above. This name corresponds to the FTP login name set in the firmware of

the device (Access Setup section). If you wish to change the user name here,

then it also must be changed in the firmware.

Password:The password corresponds to the user name above. It should be

changed according to the device password. (The default password as shown

above is ftppassword).

Device PQZIP Folder Path:The specific path where the PQZIP folders are

stored on the device. We do not recommend changing this setting.

FTP Protocol:The default setting is Passive.

Select to complete the Device Configuration.

SEE ALSO:



Log Viewer

Schedule Operation

Folders Setup





74/356

74

Folders Setup

To configure the Folder(s) size limits, selectFolders Setup by right clicking

the Nodein the Downloading Column:

This will open the Folderstab directly in theNode Configurationwindow:

Set:


75/356

75

Incoming Folder Size Limit: The size of the temporary folder where the

PQZIP files are stored while they are waiting to be processed. The default is

2 GB, although this can be changes according to your available system

resources. All original PQZIP files are deleted after they are processed

unless they are backed up.

Backup Folder Size Limit:To enable this feature, check the Backup Folder

Size Limit check-box. This sets the size of the backup folder where all good

PQZIP files can be archived. When the file folder reaches its limit, the

oldest files will be deleted first.

Bad File Folder Size Limit:The size of the bad file folder where all bad

PQZIP files are kept. A file status (good or bad) is determined when the file

is processed.

SEE ALSO:



Log Viewer

Schedule Operation

IP Setup





76/356

76


The Incoming Folder is where the PQZIP files are stored while they are waiting to

be processed. Accessing the incoming folder allows you to manually download

PQZIP files from any location on your PC or external location into the incoming

folder instead of from the device.

Right click on the Node in the Downloading Column select Openincoming folder:

The PQZIP files are arranged chronologically according to time. (AFTER

THE FILES ARE PROCESSED BY THE PQSCADA, THEY WILL NO LONGER

APPEAR IN THE INCOMING FOLDER & WILL BE DELETED. SHOULD YOU

WISH TO RECALL THE FILES SEERESET PQZIP FILES). You may select anyfile(s) from the list:


77/356

77

PQSCADA also allows you to download folders as well as files to the incoming

folder.

SEE ALSO:

PQZIP Upload Manager

Dynamic Folder Path



Log Viewer

Schedule Operation

IP Setup

Folders Setup







For a Video demonstration of downloading files to the Incoming

Folder.
http://www.elspec-ltd.com/category/Instructional_Videoshttp://www.elspec-ltd.com/category/Instructional_Videoshttp://www.elspec-ltd.com/category/Instructional_Videoshttp://www.elspec-ltd.com/category/Instructional_Videoshttp://www.elspec-ltd.com/category/Instructional_Videoshttp://www.elspec-ltd.com/category/Instructional_Videos


78/356

78


This action resets the PQZIP folder cache & generates a full folder scan on thisdevice.

Enable the Data Downloading Right click on the Node in the

Downloading Column select Rescan Device Folders:

SEE ALSO:



Log Viewer

Schedule Operation

IP Setup

Folders Setup




79/356

79




For a Video demonstration of downloading files to the Incoming

Folder.
http://www.elspec-ltd.com/category/Instructional_Videoshttp://www.elspec-ltd.com/category/Instructional_Videoshttp://www.elspec-ltd.com/category/Instructional_Videoshttp://www.elspec-ltd.com/category/Instructional_Videoshttp://www.elspec-ltd.com/category/Instructional_Videoshttp://www.elspec-ltd.com/category/Instructional_Videos


80/356

80

Enable / Disable Data Downloading

The node is set from the factory with downloading disabled. In order to

automatically download new PQZIP files from the device, it is necessary to enable

downloading. If you choose to manually download files, then you do not need to

enable downloading.

Right click the Node in the Downloading column, then select Enable or

Disable.

SEE ALSO:



Log Viewer

Schedule Operation

IP Setup

Folders Setup




81/356

81

Data Processing

The Data Processing column displays the processing status of PQZIP data. In order

to activate the tools for this column, you will need to Enablethe function by right

clicking anywhere in the Data Processing Column & selecting Enable:

The data processing takes place in 2 stages - namely:

Stage 1 - Data Transferral from the PQZIP to the Database, including:

Decompression & collection of waveform data sources

Data is recompressed into 1min chunks called BINARIES

The Binaries & Device Events are stored into the Database

RMS (V/I) are computed into 1min Summaries

After this stage has been concluded, the minimum resolution period that is

available for all the parameters, is 3 Hours.

Stage 2 - Data Processing itself:

Computation of all other parameter summaries

Computation of Class A aggregated parameters (Version 4)

Summaries are stored every 1 Min / 10 Min ( Min/Max/AVG)After this stage has been concluded, all queries may run for a period longer

than 3 Hours.

The Binaries calculated during Stage 1 are used for:

Stage 2 computation

Queries that are initiated from Elspec's Investigator Software Program for

less than 3hours. Any selected parameter is immediately computed from

the stored waveform signal in order to achieve a maximum resolution.

The summaries are used for queries that are run for a longer period than 3

Hours & this consequently shortens the response time for such queries.


82/356

82

By right clicking anywhere in the Data Processing Column, it is possible toaccess the following tools:

Refresh:Will update you on the Data Processing status for the Node(s).

Log Viewer

Force File Parse Attempt

Configure Service

Reset PQZIP files

Folders Setup


Open "Bad Files" Folder

Open Data Backup Folder

En/Disable Processing

Re-Index


83/356

83

Delete Data

Recalculate Data

Swap Phases

Add Factor Parameters

Double-clicking either theServerorNodewithin this column, will navigate youdirectly to the following Configurationoptions: General Configurationfor the

server & Parameters for the node. On mouse-over Tooltips will appear for

eachComponent.


84/356

84

Log Viewer

The Log Viewer enables you to see specific information related to log entries & in

this specific case displays entries related to the processing status of PQZIP data.

Right click anywhere in the Data Processing Column select Log Viewer:

Use the following Filters to narrow-down your view:

Log Type: (Debug, Info, Warning, Error, Critical)

Debug: By default this option is disabled & it is used only by

an Elspec Software Technician.

Info: Will include general information on actions taken in

PQSCADA. In addition, it will also include Warnings, Error &

Critical entries.

Warning: Will include any malfunctions that the PQSCADA will

resolve by itself. The log will also include any Errors & Critical

entries.

Error: Includes malfunctions that the PQSCADA was unable to

resolve. For example failed Tasks due to an incorrect E-Mail


85/356

85

address. See Troubleshooting. The log will also include any

Critical entries.

Critical: Contact Elspec or your local representative.

# of Last Entries: This function will enable you to extract only the

desired number of Last Entries from the vast amount of all the

recorded data, allowing you to focus on the latest relevant data.

Start / End Date & Time: Select Start Date & Time option, shouldyou wish to change your search to include entries from a different

date & time

Entries in the Log Viewer from this column are related to the

processing status of PQZIP data & will initially automatically display

these entries. Should you wish, you may Include any other Keywords

into your search:

SEE ALSO:

About Data Processing

Log Viewer


Configure Service

Reset PQZIP files


86/356

86

Folders Setup





Re-Index

Delete Data

Recalculate Data

Swap Phases



87/356

87


The PQZIP files are continuously being downloaded from the device into the

temporary Incoming File Folder if the data processing is Enabled.They remain in

the Incoming File Folder waiting to be processed by the PQSCADA.

You may select to force the processing of the PQZIP files manually, by right

clicking anywhere in the Data Processing Column select Force File ParseAttempt:

SEE ALSO:


Log Viewer

Configure Service

Reset PQZIP files

Folders Setup


88/356

88





Re-Index

Delete Data

Recalculate Data

Swap Phases



89/356

89

c

Configure Service

This option will allow you to directly Configure Parameters for the Node,withouthaving to go throughNode Configuration.

Right click anywhere in the Data Processing Column select Configure

Service:

The Parameters Tab will now open & simplyConfigure the Parameters

for this Node:


90/356

90

By default, only Cycle by Cycle Waveform is selected. The selection is notpermanent therefore you may add more parameters in the future and mayrecalculate with new parameters.

Select the Desired Calculation Groups click .

Cycle by Cycle

Calculation Group

Definition CPU

Usage

Database

Capacity

Cycle by Cycle RMS Voltage/Current.

HRMS Voltage/Current.

THD Voltage/Current.

Crest Factor

Voltage/Current.

K-Factor Current.

U1 - Positive Sequence Voltage/Current.

U2 - Negative Sequence

Voltage/Current.

U2/U1 Voltage/Current.

U0/U1 Voltage/Current.

Active Power

Reactive Power

Apparent Power

Power Factor

Frequency 200ms (Device

frequency)

Low Low

Waveform Waveforms High Low

Frequency Cycle by Cycle Frequency High Low

Harmonics Voltage Harmonics

Current Harmonics

Active Power Harmonics

Reactive Power Harmonics

Medium Medium


91/356

91

Power Fundamental Including

Harmonics

Harmonics Only

Fundamental Only

Low Low

Statistics Frequency Low High

IEC61000-4-

30

Definition CPU

Usage

Database

Capacity

Current RMS Current

HRMS Current

THD Current

Crest Factor Current

U1 - Positive Sequence

Current

U2 - Negative Sequence

Current

U2/U1 Current

U0/U1 Current

Over Deviation Current

Under Deviation Current

High Low

Inter-

Harmonics

Inter-Harmonics Voltage

Inter-Harmonics Sub-Group

Voltage

Inter-Harmonics Angle

Inter-Harmonics Phasors

High High

Harmonics

Voltage Harmonics

Current Harmonics

Active Power Harmonics

Reactive Power Harmonics

Medium High


92/356

92

Power Fundamental Including

Harmonics

Harmonics Only

Fundamental Only

Medium Low

Aggregation Frequency 3 sec. Aggregation

Frequency Aggregation at 10

min. & 2 Hours

Medium High

Statistics DefinitionCPU

Usage

Database

Capacity

Group

Statistics

Frequency Statistics

RMS Statistics

THD Statistics

Active Power Statistics

Reactive Power Statistics

Apparent Power Statistics

Power Factor Statistics

Low High

SEE ALSO:


Log Viewer


Reset PQZIP files

Folders Setup





Re-Index

Delete Data

Recalculate Data

Swap Phases



93/356

93

Reset PQZIP Files

The PQSCADA server automatically downloads the PQZIP files recorded by the

BLACKBOX device (Node). Each downloaded PQZIP file is saved under a name by

the PQSCADA server & the server processes the files accordingly. As the files are

processed by the PQSCADA, they are removed from theIncoming Folder. Each file

that has been downloaded to the incoming folder manually or automatically, is

logged within the PQS Server (in order to avoid reprocessing & downloading). The

PQZIP File Viewer displays all downloaded files sorted by Processed &

Unprocessed (files that are still in the incoming folder). Should you wish to re-

download and / or re-process any of the files, you will need to delete the logged

file from the list.

Right-click on the node in the Data Processing Column selectReset PQZIP

Files:


94/356

94

The PQZIP File Viewerwindow for the selected node will now open:

FILTER:

The filter helps you narrow down your search. Select the status for the displayed PQZIP

files:

All:This will show all PQZIP files contained in the Incoming Folder. This includes

both processed and unprocessed files. It is possible to limit the number of files

using the Total Results.

Processed:Only processed files are displayed.

Unprocessed:Only unprocessed fi

Pqs User Manual Smx-0619-0102 v1.1

Documents

Transcript of Pqs User Manual Smx-0619-0102 v1.1