powRgrip System - Productivity Inc · REGO-FIX’s powRgrip System is a unique collet-holding...

powRgrip System

30 Matching Products31 Maximum & Minimum Tool Depth32 Weldon Flats & h6 Shank tolerances

PG

1COL1116.1 09/2013

Home

More Technical Information available at WWW.REGO-FIX.COM

powRgrip® What is powRgrip?

Swiss QualityMade in Switzerland to ISO 9001/ISO 14001.

What is powRgrip REGO-FIX’s powRgrip System is a unique collet-holding system that utilizes a special shallow-tapered collet that is pressed into a holder with a matching taper. This state-of-the-art system uses either a hydraulic hand-pump or a table top hydraulic press specifically designed to quickly insert these collets with up to 9 tons of force.

T.I.R. of the Whole System < 0.0001" (3 μm)Highest clamping force and lowest runout.

Taper Accuracy AT3Better spindle-to-holder fit and accuracy.

Surface Finish max. Ra 0.25Higher clamping force and higher transferable torque.

Q+® Balancing 100% balanced to lowest possible residual imbalance.

• Steep Taper balanced to G2.5 @ 22,000 rpm• BT 30 Taper balanced to 30,000 rpm• HSK 25 balanced to 90,000 rpm• HSK 32 balanced to 60,000 rpm• HSK 40 balanced to 45,000 rpm• HSK 50 balanced to 30,000 rpm• HSK 63 G2.5 @ 25,000 rpm• HSK 80 G2.5 @ 25,000 rpm• HSK 100 G2.5 @ 25,000 rpm• HSK 125 G2.5 @ 25,000 rpm

Hi-Q® Balancing System Ready to accept Hi-Q® balancing rings which will allow for the offset of the imbalance introduced by the cutting tool up to 80,000 rpm.

Minimal Outside DimensionsSlim design provides more processing flexibility.

FastTool clamping with hydraulic press < 10 seconds.

Excellent at Small DiametersClamping of small diameter tools from Ø 0.2 mm.

Presetable Tooling SystemRepeatability < 0.0004" (10 μm)

PG

2COL1116.1 09/2013

Home


powRgrip® Features Benefits

T.I.R. of < 0.0001" (3 μm)

Clamping operation in less than 10 seconds when using the PGU automatic machine.

High vibration dampening due to the interupted surfaces between the toolholder to collet and the collet to tool shank.

Highest transferable torque and lowest T.I.R., even after 20,000 tool changes

For 5 years or 20,000 cycles, REGO-FIX® guarantees the T.I.R. of a properly maintained powRgrip® holder and collet will not exceed 0.0001” and that the impregnated surface treatment will not erode.

Precise length adjustmentrepeatability <0.0004" (10 μm)

Clamps all types of toolshanks and materials in h6 tolerance from Ø 0.0079" – 1.0" (0.2 – 25.4 mm)

Developed for optimal productivity such as High Speed Cutting (HSC) and High Performance Cutting (HPC)

Transferable Torque of the powRgrip® System

PG

3COL1116.1 09/2013

Home


Information

PG ToolholdersApplicationsThese toolholders are designed for use on CNC machining centers with automatic tool changers. They are especially suited for High Speed Cutting (HSC) and High Performance Cutting (HPC) operations where processing reaches the machine limits. The vibration dampening of PG colletholders reduce spindle wear and extend tool life.

BalancingREGO-FIX® Q+® System PG toolholders are balanced by design to G 2.5 @ 22,000 rpm for steep taper holders and up to 90,000 rpm for HSK holders. Type H toolholders are ready to accept Hi-Q® balancing rings which allow precision balancing of the system up to 80,000 rpm depending on the balancing rings used.

Coolant ThroughFor use with coolant through tools.

Peripheral CoolingPG-CF collets for peripheral cooling with non-coolant through tools.

Matched Tooling System for Best FitFor highest precision and best results the whole system counts. For that reason REGO-FIX® components are carefully matched to fit together. This guarantees best run-out and balancing.

Tool Precise preset repeatability

for both HSS and carbide tools

ColletSlightly tapered shape

maximizes clamping force

HolderSuperior runout and

vibration dampening in a variety of taper styles

As a Licensed BIG Plus manufacturer, REGO-FIX® uses new state of the art measuring and grinding systems to create the most accurate dual contact holders that can be produced.

Taper Contact

Flange Contact

PG

4COL1116.1 09/2013

Home


Standard

CAT Toolholders

TypeStandardPart No.

Form BPart No.

D[mm]

L[inch]

Balancing Rings

CAT 40 / PG 6 x 3” H 4340.70631 – 10 3 FWR 285

CAT 40 / PG 10 x 3.5" H 4340.71001 4340.71004 16 3.5 FWR 285

CAT 40 / PG 10 x 6" H 4340.71071 4340.71074 16 6 FWR 285

CAT 40 / PG 15 x 3.15" H 4340.71541 4340.71544 24 3 FWR 285

CAT 40 / PG 15 x 4" H 4340.71551 4340.71554 24 4 FWR 285

CAT 40 / PG 15 x 6" H 4340.71571 4340.71574 24 6 FWR 325/285

CAT 40 / PG 25 x 3.15" H 4340.72541 4340.72544 40 3 FWR 405

CAT 40 / PG 25 x 4" H 4340.72551 4340.72554 40 4 FWR 405

CAT 40 / PG 25 x 6" H 4340.72571 4340.72574 40 6 FWR 405/405

CAT 40 / PG 32 x 3.5” H* 2340.73201 – 50 3.5 –

CAT 40 / PG 32 x 4.3" H 4340.73251 4340.73254 50 4.3 FWR 505

CAT 40 / PG 32 x 6" H 4340.73271 4340.73274 50 6 FWR 505/505

CAT 50 / PG 10 x 4” H 4350.71051 – 16 4 FWR 405

CAT 50 / PG 15 x 4” H 4350.71551 – 24 4 FWR 405

CAT 50 / PG 25 x 4" H 4350.72551 4350.72554 40 4.0 FWR 505

CAT 50 / PG 25 x 6" H 4350.72571 4350.72574 40 6.0 FWR 505/405

CAT 50 / PG 32 x 4.3" H 4350.73251 4350.73254 50 4.3 FWR 505

CAT 50 / PG 32 x 6" H 4350.73271 4350.73274 50 6 FWR 505/505

*Not for use with balancing rings.

CAT CAT+ PG

Form B


D[mm]

L[inch]

Balancing Rings

CAT+ 40 / PG 10 x 3.5" H 4340.71006 16 3.5 FWR 285

CAT+ 40 / PG 10 x 6" H 4340.71076 16 6 FWR 285

CAT+ 40 / PG 15 x 3.15" H 4340.71546 24 3 FWR 285

CAT+ 40 / PG 15 x 6" H 4340.71576 24 6 FWR 325/285

CAT+ 40 / PG 25 x 3.15" H 4340.72546 40 3 FWR 405

CAT+ 40 / PG 25 x 6" H 4340.72576 40 6 FWR 405/405

CAT+ 40 / PG 32 x 3.5” 2340.73206 50 3.5 –

CAT+ 40 / PG 32 x 6” 4340.73276 50 6 FWR 505/405

CAT+ 50 / PG 10 x 4” H 4350.71056 16 4 FWR 405

CAT+ 50 / PG 15 x 4” H 4350.71556 24 4 FWR 405

CAT+ 50 / PG 25 x 4” H 4350.72556 40 4 FWR 505

CAT+ 50 / PG 25 x 6” H 4350.72576 40 6 FWR 505/405

CAT+ 50 / PG 32 x 4.3” H 4350.73256 50 4.3 FWR 505

CAT+ 50 / PG 32 x 6” H 4350.73276 50 6 FWR 505/505

“BIG-PLUS SYSTEM - Licensed by BIG Daishowa”

CAT+ 40 Toolholders

PG

5COL1116.1 09/2013

Home


Standard

TC Toolholders (DIN 69871)


Form BPart No.

D[mm]

L[mm]

Balancing Rings

TC 30 / PG 10 x 060* 2230.71020 – 16 60 –

TC 30 / PG 10 x 073 H 4230.71030 – 16 73 FWR 285

TC 30 / PG 15 x 060* 2230.71520 – 24 60 –

TC 30 / PG 15 x 080 H 4230.71540 – 24 80 FWR 285

TC 30 / PG 15 x 120 H 4230.71560 – 24 120 FWR 285

TC 30 / PG 25 x 080* 2230.72540 – 40 80 –

TC 30 / PG 25 x 160 H 4230.72580 – 40 160 FWR 405

TC 40 / PG 10 x 080 H 4240.71040 4240.71043 16 80 FWR 285

TC 40 / PG 10 x 120 H 4240.71060 4240.71063 16 120 FWR 285

TC 40 / PG 10 x 160 H 4240.71080 4240.71083 16 160 FWR 325

TC 40 / PG 15 x 072* 2240.71530 2240.71533 24 72 –

TC 40 / PG 15 x 080 H 4240.71540 4240.71543 24 80 FWR 285

TC 40 / PG 15 x 120 H 4240.71560 4240.71563 24 120 FWR 325

TC 40 / PG 15 x 160 H 4240.71580 4240.71583 24 160 FWR 325/285

TC 40 / PG 25 x 072* 2240.72530 2240.72533 40 72 –

TC 40 / PG 25 x 080 H 4240.72540 4240.72543 40 80 FWR 405

TC 40 / PG 25 x 120 H 4240.72560 4240.72563 40 120 FWR 405

TC 40 / PG 25 x 160 H 4240.72580 4240.72583 40 160 FWR 405/405

TC 40 / PG 32 x 080* 2240.73240 2240.73243 50 80 –

TC 50 / PG 25 x 081* 2250.72540 2250.72543 40 81 –

TC 50 / PG 25 x 100 H 4250.72550 4250.72553 40 100 FWR 505

TC 50 / PG 25 x 160 H 4250.72580 4250.72583 40 160 FWR 505/405

TC 50 / PG 25 x 200 H 4250.72590 4250.72593 40 200 FWR 505/405

TC 50 / PG 32 x 080* 2250.73240 2250.73243 50 80 –


Form B

TC PG

PG

6COL1116.1 09/2013

Home



Form BPart No.

D[mm]

L [mm]

Balancing Rings

BT 30 / PG 6 x 050 2130.70610 – 10 50 –

BT 30 / PG 6 x 100 H 4130.70650 – 10 100 –

BT 30 / PG 10 x 062* 2130.71020 – 16 62 –

BT 30 / PG 10 x 080 H 4130.71040 – 16 80 FWR 285

BT 30 / PG 10 x 120 H 4130.71060 – 16 120 FWR 285

BT 30 / PG 10 x 160 H 4130.71080 – 16 160 FWR 285

BT 30 / PG 15 x 070 H 4130.71530 – 24 70 FWR 285

BT 30 / PG 15 x 120 H 4130.71560 – 24 120 FWR 285

BT 30 / PG 25 x 080 H 4130.72540 – 40 80 FWR 405

BT 30 / PG 25 x 120 H 4130.72560 – 40 120 FWR 405

BT 30 / PG 25 x 160 H 4130.72580 – 40 160 FWR 405/405

BT 40 / PG 10 x 080 H 4140.71040 4140.71043 16 80 FWR 285

BT 40 / PG 10 x 120 H 4140.71060 4140.71063 16 120 FWR 325

BT 40 / PG 10 x 160 H 4140.71080 4140.71083 16 160 FWR 325

BT 40 / PG 15 x 080 H 4140.71540 4140.71543 24 80 FWR 285

BT 40 / PG 15 x 120 H 4140.71560 4140.71563 24 120 FWR 325

BT 40 / PG 15 x 160 H 4140.71580 4140.71583 24 160 FWR 325/285

BT 40 / PG 25 x 080 H 4140.72540 4140.72543 40 80 FWR 405

BT 40 / PG 25 x 120 H 4140.72560 4140.72563 40 120 FWR 405

BT 40 / PG 25 x 160 H 4140.72580 4140.72583 40 160 FWR 405/405

BT 40 / PG 32 x 086* 2140.73240 2140.73243 50 86 –

BT 50 / PG 10 x 120 H 4150.71060 – 16 120 FWR 405

BT 50 / PG 10 x 160 H 4150.71080 – 16 160 FWR 405

BT 50 / PG 15 x 120 H 4150.71560 – 24 120 FWR 325

BT 50 / PG 15 x 160 H 4150.71580 – 24 160 FWR 325

BT 50 / PG 25 x 100* 2150.72550 – 40 100 –

BT 50 / PG 25 x 120 H 4150.72560 – 40 120 FWR 505

BT 50 / PG 25 x 160 H 4150.72580 – 40 160 FWR 505/405

BT 50 / PG 25 x 200 H 4150.72590 – 40 200 FWR 505/405

BT 50 / PG 32 x 100* 2150.73250 – 50 100 –

* Not for use with balancing rings

BT Toolholders

Standard

Form B

BT BT+ PG


D [mm]

L [mm]

Balancing Rings

BT+ 30 / PG 10 x 080 H 4130.71046 16 80 FWR 285

BT+ 30 / PG 15 x 070 H 4130.71536 24 70 FWR 285

BT+ 30 / PG 25 x 080 H 4130.72546 40 80 FWR 405

BT +30 / PG 25 x 160H 4130.72586 40 160 FWR 405/405

BT+ 40 / PG 10 x 080 H 4140.71046 16 80 FWR 285

BT+ 40 / PG 10 x 120 H 4140.71066 16 120 FWR 325

BT+ 40 / PG 15 x 080 H 4140.71546 24 80 FWR 285

BT +40 / PG 15 x 120H 4140.71566 24 120 FWR 325

BT+ 40 / PG 25 x 080 H 4140.72546 40 80 FWR 405

BT+ 40 / PG 25 x 120 H 4140.72566 40 120 FWR 405

BT+ 40 / PG 25 x 160 H 4140.72586 40 160 FWR 405/405

BT+ 50 / PG 25 x 120 H 4150.72566 40 120 FWR 505

BT+ 50 / PG 25 x 160 H 4150.72586 40 160 FWR 505/405


BT+ Toolholders

PG

7COL1116.1 09/2013

Home


1

2

Form B

Extensions

Type Part No.D

[mm]D1 h6[mm]

L[mm]

L1[mm] Drawing

CYL 10 / PG 6 x 120 2610.70620 10 10 35 124 1

CYL 10 / PG 10 x 120 2610.71020 16 10 120 40 2

CYL 20 / PG 10 x 120 2620.71020 16 20 120 50 1

CYL 20 / PG 10 x 160 2620.71040 16 20 160 50 1

CYL 20 / PG 10 x 200 2620.71060 16 20 200 50 1

CYL 20 / PG 15 x 120 2620.71520 24 20 120 50 2

CYL 25 / PG 15 x 045 2625.71522 24 25 50 60 2

CYL 1“ / PG 25 x 045 2625.71523 24 1“ 50 60 2

CYL 25 / PG 25 x 80 8020.25080 40 25 80 50 2

CYL 25 / PG 25 X 100 8020.25100 40 25 100 50 2

CYL 25 / PG 25 X 120 8020.25120 40 25 120 50 2

PG Toolholders Type OM


D [mm]

L[mm] Balancing Rings

BT-OM 30 / PG 10 x 062 H 2130.71028 16 62 –

BT-OM 30 / PG 15 x 070 H 4130.71538 24 70 FWR 285

BT-OM 30 / PG 25 x 080 H 4130.72548 40 80 FWR 405

OM Type holders have no drive keys

CYL PG

BT OM PG

PG

8COL1116.1 09/2013

Home


HSK - Form A Holders

Type Part No.D

[mm]L

[mm]Balancing

Rings

HSK-A 32 / PG 10 x 060* 2532.71020 16 60 –

HSK-A 32 / PG 15 x 075* 2532.71530 24 75 –

HSK-A 40 / PG 6 x 048* 2540.70610 10 48 –

HSK-A 40 / PG 6 x 080 H 4540.70640 10 80 FWR 225

HSK-A 40 / PG 10 x 062* 2540.71020 16 62 –

HSK-A 40 / PG 15 x 080 H 4540.71540 24 80 FWR 285

HSK-A 40 / PG 25 x 100 H 4540.72550 40 100 FWR 405

HSK-A 50 / PG 10 x 080 H 4550.71040 16 80 FWR 285

HSK-A 50 / PG 15 x 080 H 4550.71540 24 80 FWR 285

HSK-A 50 / PG 25 x 100 H 4550.72550 40 100 FWR 405

HSK-A 63 / PG 6 x 080 H 4563.70640 10 80 FWR 325

HSK-A 63 / PG 10 x 080 H 4563.71040 16 80 FWR 325

HSK-A 63 / PG 10 x 120 H 4563.71060 16 120 FWR 325

HSK-A 63 / PG 10 x 160 H 4563.71080 16 160 FWR 325

HSK-A 63 / PG 10 x 200 H 4563.71090 16 200 FWR 325

HSK-A 63 / PG 15 x 080 H 4563.71540 24 80 FWR 325

HSK-A 63 / PG 15 x 120 H 4563.71560 24 120 FWR 325

HSK-A 63 / PG 15 x 160 H 4563.71580 24 160 FWR 325/285

HSK-A 63 / PG 25 x 100 H 4563.72550 40 100 FWR 405

HSK-A 63 / PG 25 x 120 H 4563.72560 40 120 FWR 405

HSK-A 63 / PG 25 x 160 H 4563.72580 40 160 FWR 405/405

HSK-A 63 / PG 25 x 200 H 4563.72590 40 200 FWR 405/405

HSK-A 63 / PG 32 x 100* 2563.73250 50 100 –

HSK-A 63 / PG 32 x 120 H 4563.73260 50 120 FWR 505

HSK-A 80 / PG 15 x 085 H 4580.71540 24 85 FWR 325

HSK-A 80 / PG 25 x 100 H 4580.72550 40 100 FWR 505

HSK-A 80 / PG 32 x 105 H 4580.73250 50 105 FWR 505

HSK-A 100 / PG 10 x 085 H 4500.71040 16 85 FWR 405

HSK-A 100 / PG 10 x 160 H 4500.71080 16 160 FWR 405

HSK-A 100 / PG 15 x 085 H 4500.71540 24 85 FWR 405

Type Part No.D

[mm]L

[mm]Balancing

Rings

HSK-A 100 / PG 15 x 160 H 4500.71580 24 160 FWR 405/285

HSK-A 100 / PG 25 x 100 H 4500.72550 40 100 FWR 505

HSK-A 100 / PG 25 x 160 H 4500.72580 40 160 FWR 505/405

HSK-A 100 / PG 25 x 200 H 4500.72590 40 200 FWR 505/405

HSK-A 100 / PG 32 x 106 H 4500.73250 50 106 FWR 505

HSK-E 25 / PG 6 x 043* 2525.70614 10 43 –

HSK-E 25 / PG 10 x 055* 2525.71014 16 55 –

HSK-E 32 / PG 6 x 048* 2532.70614 10 48 –

HSK-E 32 / PG 10 x 060* 2532.71024 16 60 –

HSK-E 32 / PG 10 x 080 H 4532.71044 16 80 FWR 225

HSK-E 32 / PG 15 x 075* 2532.71534 24 75 –

HSK-E 40 WM / PG 6 x 048*+ 2540.70617 10 48 –

HSK-E 40 WM / PG 10 x 052*+ 2540.71017 16 52 –

HSK-E 40 WM / PG 10 x 062*+ 2540.71027 16 62 –

HSK-E 40 / PG 6 x 048* 2540.70614 10 48 –

HSK-E 40 / PG 6 x 080 4540.70644 10 80 FWR 225

HSK-E 40 / PG 10 x 062* 4540.70644 16 62 –

HSK-E 40 / PG 10 x 080 H 4540.71044 16 80 FWR 225

HSK-E 40 WM / PG 10 x 080 H+ 4540.71047 16 80 FWR225

HSK-E 40 / PG 10 x 120 H 4540.71064 16 120 FWR 225

HSK-E 40 / PG 10 x 160 H 4540.71084 16 160 FWR 285

HSK-E 40 WM / PG 15 x 064*+ 2540.71527 24 64 –

HSK-E 40 / PG 15 x 080 H 4540.71544 24 80 FWR 285

HSK-E 40 WM / PG 15 x 080 H+ 4540.71547 24 80 FWR 285

HSK-E 40 / PG 15 x 120 H 4540.71564 24 120 FWR 285

HSK-E 40 / PG 25 x 090* 2540.72544 40 90 –

HSK-E 40 / PG 25 x 100 H 4540.72554 40 100 FWR 405

HSK-E 50 / PG 6 x 080 H 4550.70644 10 80 FWR 285

HSK-E 50 / PG 10 x 080 H 4550.71044 16 80 FWR 285

HSK-E 50 / PG 10 x 120 H 4550.71064 16 120 FWR 285

HSK - Form A & E Holders Continued

HSK PG

* Not for use with balancing rings. * Not for use with balancing rings. +Compatible with Willemin-Macodel Machines

PG

9COL1116.1 09/2013

Home


HSK PG

HSK - Form E Holders Continued

Type Part No.D

[mm]L

[mm]Balancing

Rings

HSK-E 50 / PG 10 x 160 H 4550.71084 16 160 FWR 285

HSK-E 50 / PG 15 x 080 H 4550.71544 24 80 FWR 285

HSK-E 50 / PG 15 x 120 H 4550.71564 24 120 FWR 285

HSK-E 50 / PG 25 x 100 H 4550.72554 40 100 FWR 405

HSK-F 63 / PG 10 x 080 H 4563.71045 16 80 FWR 325

HSK-F 63 / PG 10 x 120 4563.71065 16 120 FWR 285

HSK-F 63 / PG 10 x 160 4563.71085 16 160 FWR 285

HSK-F 63 / PG 15 x 080 H 4563.71545 24 80 FWR 325

HSK-F 63 / PG 15 x 120 H 4563.71565 24 120 FWR 325

HSK-F 63 / PG 15 x 160 H 4563.71585 24 160 FWR 325

HSK-F 63 / PG 25 x 100 H 4563.72555 40 100 FWR 405

HSK-F 63 / PG 25 x 160 H 4563.72585 40 160 FWR 405/405

HSK-F 63 / PG 32 x 100* 2563.73255 50 100 –

HSK-F 80 Call For Availability 800-999-7346

* Not for use with balancing rings.

PG

10COL1116.1 09/2013

Home


Type Part No.D

[mm]L

[mm]Balancing

Rings

C3 / PG 6 x 045* 2803.70610 10 45 –

C3 / PG 10 x 055* 2803.71010 16 55 –

C3 / PG 15 x 067* 2803.71520 24 67 –

C4 / PG 6 x 048* 2804.70610 10 48 –

C4 / PG 10 x 060* 2804.71020 16 60 –

C4 / PG 10 x 080 H 4804.71040 16 80 FWR 225

C4 / PG 15 x 062* 2804.71520 24 62 –

C4 / PG 15 x 080 H 4804.71540 24 80 FWR 285

C5 / PG 6 x 080 H 4805.40640 10 80 FWR 285

C5 / PG 10 x 060* 2805.71020 16 60 –

C5 / PG 10 x 080 H 4805.71040 16 80 FWR 285

C5 / PG 10 x 120 H 4805.71060 16 120 FWR 285

C5 / PG 15 x 065* 2805.71520 24 65 –

C5 / PG 15 x 080 H 4805.71540 24 80 FWR 285

C5 / PG 15 x 120 H 4805.71560 24 120 FWR 325

C5 / PG 25 x 080* 2805.72540 40 80 –

C5 / PG 25 x 100 H 4805.72550 40 100 FWR 405

REGO-FIX CAPTO Holders

REGO-FIX CAPTO PG

Type Part No.D

[mm]L

[mm]Balancing

Rings

C6 / PG 10 x 080 H 4806.71040 16 80 FWR 325

C6 / PG 10 x 120 H 4806.71060 16 120 FWR 325

C6 / PG 10 x 160 H 4806.71080 16 160 FWR 325

C6 / PG 15 x 080 H 4806.71540 24 80 FWR 325

C6 / PG 15 x 120 H 4806.71560 24 120 FWR 325

C6 / PG 15 x 160 H 4806.71580 24 160 FWR 325

C6 / PG 25 x 085* 2806.72540 40 85 –

C6 / PG 25 x 100 H 4806.72550 40 100 FWR 405

C6 / PG 25 x 120 H 4806.72560 40 120 FWR 405

C6 / PG 25 x 160 H 4806.72580 40 160 FWR 405

C6 / PG 32 x 090* 2806.73240 50 90 –

C8 / PG 25 x 092* 2808.72540 40 92 –

C8 / PG 32 x 090* 2808.73240 50 90 –


PG

11COL1116.1 09/2013

Home


VDI PG

The PG VDI holder program brings the benefits to lathes that until now, only milling machines have taken advantage of for years. These include better TIR, improved tool dampening, easier presetting, longer tool life and unparalleled clamping forces.

Type Part No.D

[mm]D1

[mm]L

[mm]L1

[mm]

VDI 30 / PG 15 x 077 2930.71530 24 30 77 55

VDI 30 / PG 25 x 082 2930.72540 40 30 82 60

VDI 40 / PG 15 x 077 2940.71530 24 40 77 55

VDI 40 / PG 25 x 082 2940.72540 40 40 82 60

VDI 50 / PG 15 x 085 2950.71540 24 50 85 55

VDI 50 / PG 25 x 090 2950.72540 40 50 90 60

The PG Cylindrical Turning holders have all of the features that you expect from the PG system, now available for machines that require cylindrical holders. Available in the most common mounting block and turret diameters, these holders will bring new precision and repeatability to any machine application.

Type Part No.D

[mm]D1

[mm]L

[mm]L1

[mm]

CYL-T 25 / PG 15 x 045 2625.71522 24 25 50 60

CYL-T 32 / PG 15 x 045 2632.71522 24 32 50 60

CYL-T 32 / PG 25 x 070 2632.72542 40 32 70 60

CYL-T 40 / PG 15 x 050 2640.71522 24 40 55 60

CYL-T 40 / PG 25 x 065 2640.72542 40 40 65 60

CYL-T 1“ / PG 15 x 045 2625.71523 24 1“ 50 60

CYL-T 1 1/4“ / PG 15 x 045 2631.71523 24 1 1/4“ 50 60

CYL-T 1 1/4“ / PG 25 x 070 2631.72543 40 1 1/4“ 70 60

CYL-T 1 1/2“ / PG 15 x 050 2638.71523 24 1 1/2“ 55 60

CYL-T 1 1/2“ / PG 25 x 065 2638.72543 40 1 1/2“ 65 60

Cylindrical PG

VDI Toolholders

Cylindrical Toolholders

PG

12COL1116.1 09/2013

Home


Type Part No.L

[mm]D

[mm]Fine Thread Main Nut

ER 20 M / PG 10 7661.20100 35.5 16

ER 25 M / PG 15 7661.25150 36 24

Coarse Thread Main Nut

ER 20 / PG 10 7660.20100 35.5 16

ER 25 / PG 15 7660.25150 36 24PGU Automatic or PGC hand-pump is required

for use with the powRgrip System

What is Swiss Quick?

powRgrip / ER Reductions

Swiss Quick Tool Changing System

Swiss QualityMade in Switzerland to ISO 9001/ISO 14001.

What is Swiss Quick Tool Changing SystemOne of the latest REGO-FIX innovations is the SwissQuick ER to ER adapter. These are short “mini-holders” with a solid ER body profile on the back end, and a smaller ER series cavity on the front end. This unique design results in the shortest and most rigid ER to ER reduction available. Because of the solid body design, accuracy can be improved with a taper to collet cavity TIR of less than 0.0001” (3 um), and are repeatable within 0.0005” on tool length. Locking RingSpecial locking ring to insure that the collet body is removed with the nut.

Matched Tooling System for Best FitFor highest precision and best results the whole system counts. For that reason REGO-FIX® components are carefully matched for optimum fit and accuracy. This guarantees the best run-out and balance.

TIR of the SystemPG run-out of 0.0001” or better when using the REGO-FIX® powRgrip® System.

ER run-out of 0.0002” or better with a REGO-FIX® UP Collet

PG

13COL1116.1 09/2013

Home


CYL SSY PG DIN 1835 B+E

PG Softsynchro®

Tapping HolderApplicationsREGO-FIX® Softsynchro® tapping holders are used on machines that are designed for direct tapping. Many of the newer CNC machines feature synchronization between spindle feed and thread pitch. This allows to use rigid tapping holders. However due to the dynamics of spindle and linear motors synchronization errors occur. To compensate for these synchronization errors Softsynchro® tapping holders with minimal length adjustment are necessary. Depending on the application Softsynchro® tapping holders increase tool life up to 150%.

Comparison TestsThe two diagrams show the axial forces when cold-forming M10 threads in St37 steel.

Conclusion: Axial forces increase with increasing rpm. With REGO-FIX® Softsynchro® tapping holders the forces are considerably lower than when using rigid tapping toolholders. Therefore the surface quality and tool life is optimized when using Softsynchro® tapping holders on a synchronized machine spindle.

CYL SSY/PG Softsynchro® Tapping Holders

Type Part No.D

[mm]D1

[mm]L

[mm]L1

[mm]Compression

[mm]Tension[mm]

CYL 25 SSY / PG 15 2625.61507 24 25 92 57 0.5 0.5

CYL 25 SSY / PG 25 2625.62507 40 25 109.5 57 0.5 0.5

HSK-A SSY/PG Softsynchro® Tapping Holders

Type Part No.D

[mm]L

[mm]Compression

[mm]Tension[mm]

HSK-A 63 SSY / PG 15 2563.61507 24 114.5 0.5 0.5

HSK-A 63 SSY / PG 25 2563.62507 40 131 0.5 0.5

3000

2500

2000

1500

1000

500

0

3000

2500

2000

1500

1000

500

0

Drehzahl 500 min -1

Axial

kraft [

N]

Zeit [s] 0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 5.5 6

Drehzahl 2000 min -1

Axial

kraft [

N]

Zeit [s] 0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 5.5 6

REGO- FIX® Softsynchro®-GewindeschneidfutterMitbewerber Synchron-WerkzeugaufnahmeStarre Synchron-Werkzeugaufnahme

3000

2500

2000

1500

1000

500

0

3000

2500

2000

1500

1000

500

0

Drehzahl 500 min -1

Axial

kraft [

N]

Zeit [s] 0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 5.5 6

Drehzahl 2000 min -1

Axial

kraft [

N]

Zeit [s] 0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 5.5 6

REGO- FIX® Softsynchro®-GewindeschneidfutterMitbewerber Synchron-WerkzeugaufnahmeStarre Synchron-Werkzeugaufnahme

r.p.m 500 min-1

Time Sec.Time Sec.

Axi

al F

orce

[N]

Axi

al F

orce

[N]

r.p.m 2000 min-1

PG

14COL1116.1 09/2013

Home


Vibration Decay Chart

This New MICRO-FRICTION DAMPENING™ (MFD) technology (pat. pending) from REGO-FIX allows the holders to dissipate vibrations faster than standard long reach holders. Dampening the vibrations faster means that your cutting tool, part and spindle will see less vibrations resulting in better surface finishes, longer tool life and less spindle wear.

Machining parameters have to be adapted to the gauge length of the Xtended Length

Toolholders

0 100 200 300 400 500 600 700-1000

-500

0

500

1000

1500

Zeit in ms / Time in ms

Bes

chle

unig

ung

in m

/s2 /

Acc

eler

atio

n in

m/s

2

0 100 200 300 400 500 600 700-1000

-500

0

500

1000

1500


Bes

chle

unig

ung

in m

/s2 /

Acc

eler

atio

n in

m/s

2

0 100 200 300 400 500 600 700-1000

-500

0

500

1000

1500


Bes

chle

unig

ung

in m

/s2 /

Acc

eler

atio

n in

m/s

2

0 100 200 300 400 500 600 700-1000

-500

0

500

1000

1500


Bes

chle

unig

ung

in m

/s2 /

Acc

eler

atio

n in

m/s

2

Standard toolholder

REGO-FIX® Xtended Length Toolholder with MFD™ Technology.

Acce

lerati

on in

m/s

2

Time in ms

Acce

lerati

on in

m/s

2

Time in ms

REGO-FIX® XL Toolholder

PG

15COL1116.1 09/2013

Home


+Holder is mono-block design and does not feature vibration dampening technology. Note: Maximum 5,000 r.p.m.

Type Part No.D1

[mm]D2

[mm]D3

[mm]L1

[mm]L2

[mm]L3

[inch]L

[inch]

CAT40 / PG 10 x 8 XL 8843.71031 16 28 42 31 84 4 8

CAT40 / PG 10 x10 XL 8843.71081 16 28 42 31 84 4 10

CAT40 / PG 10 x 12 XL 8843.71131 16 28 42 31 124 8 12

CAT40 / PG 10 x 14 XL 8843.71181 16 28 42 31 124 8 14

CAT40 / PG 15 x 8 XL 8843.73031 24 28 42 55 75 4 8

CAT40 / PG 15 x 10 XL 8843.73081 24 28 42 55 75 4 10

CAT40 / PG 15 x 12 XL 8843.73131 24 28 42 55 125 8 12

CAT40 / PG 15 x 14 XL 8843.73181 24 28 42 55 125 8 14

CAT40 / PG 25 x 8+ 4340.72591 40 – 52 – – – 8

CAT40 / PG 25 x10 XL 8843.76081 40 – 52 – – 4 10

CAT40 / PG 25 x14 XL 8843.76181 40 – 52 – – 8 14

CAT50 / PG 10 x 8 XL 8853.71031 16 28 42 31 84 4 8

CAT50 / PG 10 x 10 XL 8853.71081 16 28 42 31 84 4 10

CAT50 / PG 10 x 12 XL 8853.71131 16 28 42 31 124 8 12

CAT50 / PG 10 x 14 XL 8853.71181 16 28 42 31 124 8 14

CAT50 / PG 15 x 8 XL 8853.73031 24 28 42 55 75 4 8

CAT50 / PG 15 x 10 XL 8853.73081 24 28 42 55 75 4 10

CAT50 / PG 15 x 12 XL 8853.73131 24 28 42 55 125 8 12

CAT50 / PG 15 x 14 XL 8853.73181 24 28 42 55 125 8 14

CAT50 / PG 25 x10 XL 8853.76081 40 – 52 – – 4 10

CAT50 / PG 25 x14 XL 8853.76181 40 – 52 – – 8 14

CAT PG XLANSI B5.50

CAT XL Toolholders

PG

16COL1116.1 09/2013

Home


Type Part No.D1

[mm]D2

[mm]D3

[mm]L1

[mm]L2

[mm]L3

[mm]L

[mm]

BT40 / PG 10 x 220 XL 8841.71050 16 28 42 31 84 140 220

BT40 / PG 10 x 260 XL 8841.71090 16 28 42 31 84 140 260

BT40 / PG 10 x 300 XL 8841.71130 16 28 42 31 84 140 300

BT40 / PG 10 x 320 XL 8841.71150 16 28 42 31 124 240 320

BT40 / PG 10 x 360 XL 8841.71190 16 28 42 31 124 240 360

BT40 / PG 10 x 400 XL 8841.71230 16 28 42 31 124 240 400

BT40 / PG 15 x 220 XL 8841.73050 24 28 42 55 75 140 220

BT40 / PG 15 x 260 XL 8841.73090 24 28 42 55 75 140 260

BT40 / PG 15 x 300 XL 8841.73130 24 28 42 55 75 140 300

BT40 / PG 15 x 320 XL 8841.73150 24 28 42 55 125 240 320

BT40 / PG 15 x 360 XL 8841.73190 24 28 42 55 125 240 360

BT40 / PG 15 x 400 XL 8841.73230 24 28 42 55 125 240 400

BT40 / PG 25 x 226 XL 8841.76050 40 – 52 – – 140 226

BT40 / PG 25 x 326 XL 8841.76150 40 – 52 – – 240 326

BT50 / PG 10 x 240 XL 8851.71070 16 28 42 31 84 140 240

BT50 / PG 10 x 260 XL 8851.71090 16 28 42 31 84 140 260

BT50 / PG 10 x 300 XL 8851.71130 16 28 42 31 84 140 300

BT50 / PG 10 x 340 XL 8851.71170 16 28 42 31 124 240 340

BT50 / PG 10 x 360 XL 8851.71190 16 28 42 31 124 240 360

BT50 / PG 10 x 400 XL 8851.71230 16 28 42 31 124 240 400

BT50 / PG 15 x 240 XL 8851.73070 24 28 42 55 75 140 240

BT50 / PG 15 x 260 XL 8851.73090 24 28 42 55 75 140 260

BT50 / PG 15 x 300 XL 8851.73130 24 28 42 55 75 140 300

BT50 / PG 15 x 340 XL 8851.73170 24 28 42 55 125 240 340

BT50 / PG 15 x 360 XL 8851.73190 24 28 42 55 125 240 360

BT50 / PG 15 x 400 XL 8851.73230 24 28 42 55 125 240 400

BT50 / PG 25 x 240 XL 8851.76070 40 – 52 – – 140 240

BT50 / PG 25 x 340 XL 8851.76170 40 – 52 – – 240 340 Note: Maximum 5,000 r.p.m.

BT PG XLMAS 403

BT XL Toolholders

PG

17COL1116.1 09/2013

Home


Type Part No.D1

[mm]D2

[mm]D3

[mm]L1

[mm]L2

[mm]L3

[mm]L

[mm]

TC40 / PG 10 x 220 XL 8842.71050 16 28 42 31 84 140 220

TC40 / PG 10 x 260 XL 8842.71090 16 28 42 31 84 140 260

TC40 / PG 10 x 300 XL 8842.71130 16 28 42 31 84 140 300

TC40 / PG 10 x 320 XL 8842.71150 16 28 42 31 124 240 320

TC40 / PG 10 x 360 XL 8842.71190 16 28 42 31 124 240 360

TC40 / PG 10 x 400 XL 8842.71230 16 28 42 31 124 240 400

TC40 / PG 15 x 220 XL 8842.73050 24 28 42 55 75 140 220

TC40 / PG 15 x 260 XL 8842.73090 24 28 42 55 75 140 260

TC40 / PG 15 x 300 XL 8842.73130 24 28 42 55 75 140 300

TC40 / PG 15 x 320 XL 8842.73150 24 28 42 55 125 240 320

TC40 / PG 15 x 360 XL 8842.73190 24 28 42 55 125 240 360

TC40 / PG 15 x 400 XL 8842.73230 24 28 42 55 125 240 400

TC40 / PG 25 x 220 XL 8842.76050 40 – 52 – – 140 220

TC40 / PG 25 x 320 XL 8842.76150 40 – 52 – – 240 320

TC50 / PG 10 x 240 XL 8852.71070 16 28 42 31 84 140 240

TC50 / PG 10 x 300 XL 8852.71130 16 28 42 31 84 140 300

TC50 / PG 10 x 340 XL 8852.71170 16 28 42 31 124 240 340

TC50 / PG 10 x 400 XL 8852.71230 16 28 42 31 124 240 400

TC50 / PG 15 x 240 XL 8852.73070 24 28 42 55 75 140 240

TC50 / PG 15 x 300 XL 8852.73130 24 28 42 55 75 140 300

TC50 / PG 15 x 340 XL 8852.73170 24 28 42 55 125 240 340

TC50 / PG 15 x 400 XL 8852.73230 24 28 42 55 125 240 400

TC50 / PG 25 x 320 XL 8852.76150 40 52 240 320

Note: Maximum 5,000 r.p.m.

TC PG XLDIN 69871

TC XL Toolholders

PG

18COL1116.1 09/2013

Home


Type Part No.D1

[mm]D2

[mm]D3

[mm]L1

[mm]L2

[mm]L3

[mm]L

[mm]

HSK-A 63 / PG 10 x 240 XL 8865.71070 16 28 42 31 84 140 240

HSK-A 63 / PG 10 x 260 XL 8865.71090 16 28 42 31 84 140 260

HSK-A 63 / PG 10 x 300 XL 8865.71130 16 28 42 31 84 140 300

HSK-A 63 / PG 10 x 340 XL 8865.71170 16 28 42 31 124 240 340

HSK-A 63 / PG 10 x 360 XL 8865.71190 16 28 42 31 124 240 360

HSK-A 63 / PG 10 x 400 XL 8865.71230 16 28 42 31 124 240 400

HSK-A 63 / PG 15 x 240 XL 8865.73070 24 28 42 55 75 140 240

HSK-A 63 / PG 15 x 260 XL 8865.73090 24 28 42 55 75 140 260

HSK-A 63 / PG 15 x 300 XL 8865.73130 24 28 42 55 75 140 300

HSK-A 63 / PG 15 x 340 XL 8865.73170 24 28 42 55 125 240 340

HSK-A 63 / PG 15 x 360 XL 8865.73190 24 28 42 55 125 240 360

HSK-A 63 / PG 15 x 400 XL 8865.73230 24 28 42 55 125 240 400

HSK-A 63 / PG 25 x 240 XL 8865.76070 40 – 52 – – 140 240

HSK-A 63 / PG 25 x 260 XL 8865.76090 40 – 52 – – 140 260

HSK-A 63 / PG 25 x 340 XL 8865.76170 40 – 52 – – 240 340

HSK-A 63 / PG 25 x 360 XL 8865.76190 40 – 52 – – 240 360

HSK-A 100 / PG 10 x 240 XL 8885.71070 16 28 42 31 84 140 240

HSK-A 100 / PG 10 x 300 XL 8885.71130 16 28 42 31 84 140 300

HSK-A 100 / PG 10 x 340 XL 8885.71170 16 28 42 31 124 240 340

HSK-A 100 / PG 10 x 400 XL 8885.71230 16 28 42 31 124 240 400

HSK-A 100 / PG 15 x 240 XL 8885.73070 24 28 42 55 75 140 240

HSK-A 100 / PG 15 x 300 XL 8885.73110 24 28 42 55 75 140 300

HSK-A 100 / PG 15 x 340 XL 8885.73170 24 28 42 55 125 240 340

HSK-A 100 / PG 15 x 400 XL 8885.73230 24 28 42 55 125 240 400

HSK-A 100 / PG 25 x 246 XL 8885.76070 40 – 52 – – 140 246

HSK-A 100 / PG 25 x 346 XL 8885.76170 40 – 52 – – 240 346 Note: Maximum 5,000 r.p.m.

HSK PG XLDIN 69893

HSK XL Toolholders

PG

19COL1116.1 09/2013

Home


D2

D3

D1

L1

L2

L3

L

REGO-FIX CAPTO PG XL

Part No. TypeD1

[mm]D2

[mm]D3

[mm]L1

[mm]L2

[mm]L3

[mm]L

[mm]

C6 / PG10 x 225 XL 8886.71050 16 28 42 31 84 140 225

C6 / PG10 x 240 XL 8886.71070 16 28 42 31 84 140 240

C6 / PG10 x 260 XL 8886.71090 16 28 42 31 84 140 260

C6 / PG10 x 300 XL 8886.71130 16 28 42 31 84 140 300

C6 / PG10 x 325 XL 8886.71150 16 28 42 31 124 240 325

C6 / PG10 x 340 XL 8886.71170 16 28 42 31 124 240 340

C6 / PG10 x 360 XL 8886.71190 16 28 42 31 124 240 360

C6 / PG10 x 400 XL 8886.71230 16 28 42 31 124 240 400

C6 / PG15 x 225 XL 8886.73050 24 28 42 55 75 140 225

C6 / PG15 x 240 XL 8886.73070 24 28 42 55 75 140 240

C6 / PG15 x 260 XL 8886.73090 24 28 42 55 75 140 260

C6 / PG15 x 300 XL 8886.73130 24 28 42 55 75 140 300

C6 / PG15 x 325 XL 8886.73150 24 28 42 55 125 240 325

C6 / PG15 x 340 XL 8886.73170 24 28 42 55 125 240 340

C6 / PG15 x 360 XL 8886.73190 24 28 42 55 125 240 360

C6 / PG15 x 400 XL 8886.73230 24 28 42 55 125 240 400

C6 / PG25 x 230 XL 8886.76060 40 – 52 – – 140 230

C6 / PG25 x 330 XL 8886.76160 40 – 52 – – 240 330

C8 / PG10 x 232 XL 8888.71060 16 28 42 31 84 140 232

C8 / PG10 x 332 XL 8888.71160 16 28 42 31 124 240 332

C8 / PG15 x 232 XL 8888.73060 24 28 42 55 75 140 232

C8 / PG15 x 332 XL 8888.73160 24 28 42 55 75 240 332

C8 / PG25 x 230 XL 8888.76060 40 – 52 – – 140 230

C8 / PG25 x 330 XL 8888.76160 40 – 52 – – 240 330 Note: Maximum 5,000 r.p.m.

REGO-FIX CAPTO XL Toolholders

PG

20COL1116.1 09/2013

Home


powRgrip® Collets What are PG Collets?

Swiss QualityMade in Switzerland to ISO9001/ISO14001.

What are PG ColletspowRgrip (PG) Collets are precisely engineered to exacting tolerances. This assures that once the collets are pressed into the matching powRgrip holder, the result will be an accurately assembled system of less than 0.0001” TIR. Special metal processing provides the collets unique black appearance and results in an extremely hard surface finish that allows users to experience unmatched longevity and repeatability.

Precision Highest T.I.R. <0.0001” .

Accurate Length Adjustment <10 μmWith integrated adjustment screw.

Clamping of all h6 Tool ShanksCylindrical, WELDON, Whistle-Notch

Clamping of all Shank MaterialsSolid carbide and HSS tool shanks.

Clamping Diameters 0.2 to 25.4 mm

FastClamping in less than 10 seconds.

Simple HandlingParameters are automatically set.

High Vibration Dampening High vibration dampening due to the interface surfaces between the toolholder to collet and the collet to tool shank.

Highest Transferable TorqueThe powRgrip® system yields the highest transferable torque of all comparable systems.

Productivity and Tool LifeSpecially designed to allow for maximum machining capability.

PG

21COL1116.1 09/2013

Home


PG Collets do not have a clamping range. Nominal diameter only. Requires h6 tolerance shanks which are listed on page 31.

powRgrip® Collets

Dia.(mm)

Dia.(inch)

PG 10Part No.

PG 10CFPart No.

0.200 1710.00209 –

0.300 1710.00309 –

0.400 1710.00409 –

0.500 1710.00509 –

0.600 1710.00609 –

0.700 1710.00709 –

0.800 1710.00809 –

0.900 1710.00909 –

1.000 1710.01009 –

1.500 1710.01509 –

1.588 1/16 1710.01589 –

2.000 1710.02000 –

2.500 1710.02500 –

3.000 1710.03000 1710.03002

3.500 1710.03500 –

3.175 1/8 1710.03181 1710.03183

4.000 1710.04000 1710.04002

4.500 1710.04500 –

4.763 3/16 1710.04761 1710.04763

5.000 1710.05000 1710.05002

5.500 1710.05500 –

6.000 1710.06000 1710.06002

6.350 1/4 1710.06351 1710.06353

Dia.(mm)

Dia.(inch)

PG 6Part No.

PG 6CFPart No.

0.200 1706.00209 –

0.300 1706.00309 –

0.400 1706.00409 –

0.500 1706.00509 –

0.600 1706.00609 –

0.700 1706.00709 –

0.800 1706.00809 –

0.900 1706.00909 –

1.000 1706.01009 –

1.500 1706.01509 –

2.000 1706.02000 –

2.500 1706.02500 –

3.000 1706.03000 –

3.175 1/8” 1706.03181 –

PG 10 ColletsPG 6 Collets

PG REGO-FIX®

Standard ColletMetallic Sealed

PG REGO-FIX®

Coolant Flush

PG Collet Options

PG

22COL1116.1 09/2013

Home


PG REGO-FIX®

Standard ColletMetallic Sealed

PG REGO-FIX®

Coolant Flush

PG Collet Options

Dia.(mm)

Dia.(inch)

PG 15Part No.

PG 15CFPart No.

3.000 1715.03000 1715.03002

3.175 1/8 1715.03181 1715.03183

3.500 1715.03500 –

4.000 1715.04000 1715.04002

4.500 1715.04500 –

4.763 3/16 1715.04761 1715.04763

5.000 1715.05000 1715.05002

5.500 1715.05500 –

6.000 1715.06000 1715.06002

6.350 1/4 1715.06351 1715.06353

7.000 1715.07000 1715.07002

7.938 5/16 1715.07941 1715.07943

8.000 1715.08000 1715.08002

9.000 1715.09000 1715.09002

9.525 3/8 1715.09521 1715.09523

10.000 1715.10000 1715.10002

PG 15 Collets

powRgrip® Collets

Dia.(mm)

Dia.(inch)

PG 25Part No.

PG 25CFPart No.

PG 32Part No.

PG 32CFPart No.

3.000 1725.03000 1725.03002 – –

3.175 1/8 1725.03181 1725.03183 – –

3.500 1725.03500 – – –

4.000 1725.04000 1725.04002 – –

4.500 1725.04500 – – –

4.763 3/16 1725.04761 1725.04763 – –

5.000 1725.05000 1725.05002 – –

5.500 1725.05500 – – –

6.000 1725.06000 1725.06002 1732.06000 1732.06002

6.350 1/4 1725.06351 1725.06353 1732.06351 1732.06353

7.000 1725.07000 1725.70002 1732.07000 1732.07002

7.938 5/16 1725.07941 1725.07943 1732.07941 1732.07943

8.000 1725.08000 1725.08002 1732.08000 1732.08002

9.000 1725.09000 1725.09002 1732.09000 1732.09002

9.525 3/8 1725.09521 1725.09523 1732.09521 1732.09523

10.000 1725.10000 1725.10002 1732.10000 1732.10002

11.000 1725.11000 1725.11002 1732.11000 1732.11002

11.113 7/16 1725.11111 1725.11113 1732.11111 1732.11113

12.000 1725.12000 1725.12002 1732.12000 1732.12002

12.700 1/2 1725.12701 1725.12703 1732.12701 1732.12703

13.000 1725.13000 1725.13002 – –

14.000 1725.14000 1725.14002 1732.14000 1732.14002

14.288 9/16 1725.14291 1725.14293 1732.14291 1732.14293

15.000 1725.15000 1725.15002 – –

15.875 5/8 1725.15881 1725.15883 1732.15881 1732.15883

16.000 1725.16000 1725.16002 1732.16000 1732.16002

17.463 11/16 1175.17461 – – –

18.000 1725.18000 1725.18002 1732.18000 1732.18002

19.050 3/4 1725.19051 1725.19053 1732.19051 1732.19053

20.000 1725.20000 1725.20002 1732.20000 1732.20002

22.000 – – 1732.22000 1732.22002

22.225 7/8 – – 1732.22231 1732.22233

25.000 – – 1732.25000 1732.25002

25.400 1 – – 1732.25401 1732.25403

PG 25 & PG 32 Collets

PG

23COL1116.1 09/2013

Home


Ø[mm]

Ø[inch]

PG 15-TPart No.

PG 25-TPart No.

5.000 – 1715.05007 1725.05007

6.000 – 1715.06007 1725.06007

6.350 1/4" 1715.06357 1725.06357

8.000 – 1715.08007 1725.08007

9.525 3/8" 1715.09537 1725.09537

10.000 – 1715.10007 1725.10007

12.000 – – 1725.12007

12.700 1/2” – 1725.12707

16.000 – – 1725.16007

19.050 3/4” – 1725.19057

20.000 – – 1725.20007

The PG boring bar collets bring the ability to transform your normal PG holder into a boring bar holder without losing accuracy or repeatability. The collets are designed to hold the cylindrical boring bar and position it correctly in the PG holder.

Boring Bar Collets PG-T

Boring Bar Collets

PG

24COL1116.1 09/2013

Home


secuRgrip PG

secuRgripApplicationspowRgrip now offers an option for those most difficult machinging applications that require the ultimate in cutting tool security. secuRgrip utilizes powRgrips’ tremendous gripping strength in combination with a patented locking key system and threaded cap. These two additional levels of cutting tool security provide an added degree of confidence for those special applications such as expensive castings or complex parts.

Ease of UseUnlike other systems, secuRgrip does not require the purchase of any expensive special modified endmills from limited manufacturers. Instead, it allows for the use of standard Weldon flat tools on any standard carbide or HSS endmill.

LockingThe locking key fits into the Weldon flat prior to assembly and secures the endmill to the collet in this easy to assemble system. A special locking cap then locks the collet and cutter assembly to the holder once pressed in.

PresettingAll secuRgrip collets are designed to provide “z” height adjustment when required. secuRgrip is currently available in both the PG 25 and PG 32 holder series.

Level 1 SecurityLocking Key on

Cutting Tool

Level 2 SecurityLocking Cap for

PG Collet

PG

25COL1116.1 09/2013

Home


CAT+ PG-SG HoldersCAT PG-SG Holders

BT+ PG-SG HoldersBT PG-SG Holders

CAT secuRgrip PG

BT secuRgrip PG

TypeREGO-PLUS

D[mm]

L [mm]

Balancing Rings

CAT+ 40 / PG-SG 25 x 3.15” H 5340.72546 46 3.15 FWR 405

CAT+ 40 / PG-SG 25 x 4” H – 46 4 FWR 405

CAT+ 40 / PG-SG 25 x 6” H 5340.72576 46 6 FWR 405/405

CAT+ 40 / PG-SG 32 x 3.5”* 5340.73206 55 3.5 –

CAT+ 40 / PG-SG 32 x 4.3” H – 55 4.3 FWR 505

CAT+ 40 / PG-SG 32 x 6” H 5340.73276 55 6 FWR 505/505

CAT+ 50 / PG-SG 25 x 4” H 5350.72556 46 4 FWR 405

CAT+ 50 / PG-SG 25 x 6” H 5350.72576 46 6 FWR 405/405

CAT+ 50 / PG-SG 32 x 4.3” H 5350.73256 55 4.3 FWR 505

CAT+ 50 / PG-SG 32 x 6” H 5350.73276 55 6 FWR 505/505



Form BPart No.

D[mm]

L [mm]

Balancing Rings

CAT 40 / PG-SG 25 x 3.15” H 5340.72541 5340.72544 46 3.15 FWR 405

CAT 40 / PG-SG 25 x 4” H 5340.72551 5340.72554 46 4 FWR 405

CAT 40 / PG-SG 25 x 6” H 5340.72571 5340.72574 46 6 FWR 405/405

CAT 40 / PG-SG 32 x 3.5”* 5340.73201 – 55 3.5 –

CAT 40 / PG-SG 32 x 4.3” H 5340.73251 5340.73254 55 4.3 FWR 505

CAT 40 / PG-SG 32 x 6” H 5340.73271 5340.73274 55 6 FWR 505/505

CAT 50 / PG-SG 25 x 4” H 5350.72551 5350.72554 46 4 FWR 405

CAT 50 / PG-SG 25 x 6” H 5350.72571 5350.72574 46 6 FWR 405/405

CAT 50 / PG-SG 32 x 4.3” H 5350.73251 5350.73254 55 4.3 FWR 505

CAT 50 / PG-SG 32 x 6” H 5350.73271 5350.73274 55 6 FWR 505/505


TypeREGO-PLUS

D[mm]

L [mm]

Balancing Rings

BT+ 40 / PG-SG 25 x 80 H 5140.72546 46 80 FWR 405

BT+ 40 / PG-SG 25 x 120 H 5140.72566 46 120 FWR 405

BT+ 40 / PG-SG 25 x 160 H 5140.72586 46 160 FWR 405/405

BT+ 50 / PG-SG 25 x 120mm H 5150.72566 46 120 FWR 405

BT+ 50 / PG-SG 25 x 160mm H 5150.72586 46 160 FWR 405/405

BT+ 50 / PG-SG 25 x 200 H – 46 200 FWR 405/405


Form BPart No.

D[mm]

L [mm]

Balancing Rings

BT 40 / PG-SG 25 x 80 H 5140.72540 5140.72543 46 80 FWR 405

BT 40 / PG-SG 25 x 120 H 5140.72560 5140.72563 46 120 FWR 405

BT 40 / PG-SG 25 x 160 H 5140.72580 5140.72583 46 160 FWR 405/405

BT 50 / PG-SG 25 x 120mm H 5150.72560 – 46 120 FWR 405

BT 50 / PG-SG 25 x 160mm H 5150.72580 – 46 160 FWR 405/405

BT 50 / PG-SG 25 x 200 H 5150.72590 – 46 200 FWR 405/405



Standard Form B

PG

26COL1116.1 09/2013

Home


HSK A PG-SG Holders

HSK E & F PG-SG Holders

HSK A secuRgrip PG

HSK E & F secuRgrip PG

Type Part No.D

[mm]L

[mm]Balancing

Rings

HSK-A 63 / PG-SG 25 x 100 H 5563.72550 46 100 FWR 405

HSK-A 63 / PG-SG 25 x 120 H 5563.72560 46 120 FWR 405

HSK-A 63 / PG-SG 25 x 160 H 5563.72580 46 160 FWR 405/405

HSK-A 63 / PG-SG 25 x 200 H 5563.72590 46 200 FWR 405/40

HSK-A 63 / PG-SG 32 x 100* 5563.73250 55 100 –

HSK-A 63 / PG-SG 32 x 120 H 5563.73260 55 120 FWR 505

HSK-A 80 / PG-SG 25 x 100 H 5580.72550 46 100 FWR 405

HSK-A 80 / PG-SG 32 x 105 H 5580.73250 55 105 FWR 505

HSK-A 100 / PG-SG 25 x 100 H 5500.72550 46 100 FWR 405

HSK-A 100 / PG-SG 25 x 160 H 5500.72580 46 160 FWR 405/405

HSK-A 100 / PG-SG 25 x 200 H 5500.72590 46 200 FWR 405/405

HSK-A 100 / PG-SG 32 x 100* 5500.73250 55 100 –

HSK-A 100 / PG-SG 32 x 160* 5500.73280 55 160 –

HSK-A 100 / PG-SG 32 x 200* 5500.73290 55 200 –

HSK-A 125 / PG-SG 32 x 110* 5502.73250 55 110 –


Type Part No.D

[mm]L

[mm]Balancing

Rings

HSK-E 63 / PG-SG 25 x 100 H 5563.72554 46 100 FWR 405

HSK-F 63 / PG-SG 25 x 100 H 5563.72555 46 100 FWR 405

HSK-F 63 / PG-SG 25 x 160 H 5563.72585 46 160 FWR 405/405

HSK-F 63 / PG-SG 32 x 100mm 5563.73255 55 100 –


PG

27COL1116.1 09/2013

Home


REGO-FIX CAPTO PG-SG Holders

REGO-FIX CAPTO secuRgrip PG

Type Part No.D

[mm]L

[mm]Balancing

Rings

C5 / PG-SG 25 x 80* 5805.72540 46 80 –

C5 / PG-SG 25 x 100 H 5805.72550 46 100 FWR 405

C6 / PG-SG 25 x 085* 5806.72540 46 85 –

C6 / PG-SG 25 x 100 H 5806.72550 46 100 FWR 405

C6 / PG-SG 25 x 120 H 5806.72560 46 120 FWR 405

C6 / PG-SG 25 x 160 H 5806.72580 46 160 FWR 405/405

C6 / PG-SG 32 x 090* 5806.73240 55 90 –

C8 / PG-SG 25 x 092* 5808.72540 46 92 –

C8 / PG-SG 32 x 090* 5808.73240 55 90 –


PG

28COL1116.1 09/2013

Home


secuRgrip Replacement Inserts

secuRgrip Wrench Heads & Handles

secuRgrip PG

Type Part No.

PG 25-SG / Ø 12.0 mm 1725.12004S

PG 25-SG / Ø 1/2” 1725.12704S

PG 25-SG / Ø 14.0 mm 1725.14004S

PG 25-SG / Ø 5/8” 1725.15884S

PG 25-SG / Ø 16.0 mm 1725.16004S

PG 25-SG / Ø 18.0 mm 1725.18004S

PG 25-SG / Ø 3/4” 1725.19054S

PG 25-SG / Ø 20.0 mm 1725.20004S

PG 32-SG / Ø 12.0 mm 1732.12004S

PG 32-SG / Ø 1/2” 1732.12704S

PG 32-SG / Ø 14.0 mm 1732.14004S

PG 32-SG / Ø 5/8” 1732.15884S

PG 32-SG / Ø 16.0 mm 1732.16004S

PG 32-SG / Ø 18.0 mm 1732.18004S

PG 32-SG / Ø 3/4” 1732.19054S

PG 32-SG / Ø 20.0 mm 1732.20004S

PG 32-SG / Ø 25.0 mm 1732.25004S

PG 32-SG / Ø 1” 1732.25404SNote: Part Number Includes Insert

Type Part No.

SGI Ø 12.0 mm 7694.12000

SGI Ø 1/2” 7694.12700

SGI Ø 14.0 mm 7694.14000

SGI Ø 5/8” 7694.15880

SGI Ø 16.0 mm 7694.16000

SGI Ø 18.0 mm 7694.18000

SGI Ø 3/4” 7694.19050

SGI Ø 20.0 mm 7694.20000

SGI Ø 25.0 mm 7694.25000

SGI Ø 1” 7694.25400Note: Part Number for Insert Only

Type Part No.

SGN-PG 25 Wrench Head 7654.25000

SGN-PG 32 Wrench Head 7654.32000

SGHM Wrench Handle 8777.77777

secuRgrip Collets with Insert

PG

29COL1116.1 09/2013

Home


Type Part No. Description

PGU 9006 A (PG6-PG32) 7610.90160 110 V Machine USA/Canada

APG 906 7611.06900 PG 6 clamping insert





PGU 9006 automatic clamping unit with push-button operation and auto clamping insert recognition. Designed to make operation easy, fast and reliable. Easy interchangeable inserts and safety interlocks make the machine safe for all operators.

Type Part No. DescriptionMeasurement

W x D x HIncl.

Taper Cleaner

PGC 2506 7621.25069 powRgrip® Compact hydraulic clamping unit 450 x 492 x 280

APC 25 7622.25000 Insert for PGC 2506 for PG 25 toolholders ■APC 15 7622.15000 Insert for PGC 2506 for PG 15 toolholders ■APC 10 7622.10000 Insert for PGC 2506 for PG 10 toolholders ■APC 6 7622.06000 Insert for PGC 2506 for PG 6 toolholders ■

PGC hand pumps offer a price advantage over the PGU units while still performing the task of pressing in tools. The operator actuates the pressure by use of the lever arm until the desired pressure is achieved.

Automatic Machine & Inserts

Handpump & Inserts

PGU 9006 PGC 2506

PG

30COL1116.1 09/2013

Home


Taper Cleaner

Cleaning Paper Set

Provides a quick and easy method of cleaning the powRgrip® holder bore of oil and debris before insertion of the tool.

A soft, absorbant paper specially prepared for cleaning the powRgrip® holder bore. The paper is lint-free and chemically neutral. For one time use only! Each pack contains 250 papers.


TKCP 6 7657.06000 Taper cleaner for PG 6 colletholder






CPS 6 7658.06000 Cleaning paper set for TKCP 6 / 250 papers





Matching Products

Presetting Tool

The powRgrip® presetting tool accepts the powRgrip® collets, and is inserted into the toolholder. The tool has a small thumb wheel for precise tool length adjustments, and allows maximum repeatability in the toolholder assembly.


VEW 6 7619.06000 PG 6 Presetting tool for PG 6 colletholder





PG

31COL1116.1 09/2013

Home


powRgrip Technical Requirementsh6 Shank Tolerances

Maximum & Minimum Tool Depth

PG 10 PG 15 PG 25Dia. L L

(min)L

(max)L L

(min)L

(max)L L

(min)L

(max)1/8”, 3/16”

28 24 30 28 25 32 28 25 32

1/4” 33.5 30 35.5 36 33 40 36 33 405/16” 36 33 40 36 33 403/8” 40 37 40.5 40 37 447/16” 40 37 441/2” , 9/16”

45 42 49

5/8” 48 45 503/4” 50 47 50

Fractional Decimal Tolerance Min size1/8 0.125 0.00024 0.124763/16 0.1875 0.00031 0.187191/4 0.25 0.00035 0.249655/16 0.3125 0.00035 0.312153/8 0.375 0.00035 0.374657/16 0.4375 0.00043 0.437071/2 0.5 0.00043 0.499579/16 0.5625 0.00043 0.562075/8 0.625 0.00043 0.624573/4 0.75 0.00051 0.749497/8 0.875 0.00051 0.874491.0 1.000 0.00051 0.99949

LDia.

Metric Tolerance Min size Inch Conv.2.00 0.0060 1.9940 0.078503.00 0.0060 2.9940 0.117874.00 0.0080 3.9920 0.157175.00 0.0080 4.9920 0.196546.00 0.0080 5.9920 0.235917.00 0.0090 6.9910 0.275248.00 0.0090 7.9910 0.314619.00 0.0090 8.9910 0.3539810.00 0.0090 9.9910 0.3933511.00 0.0110 10.9890 0.4326412.00 0.0110 11.9890 0.47201

13.00 0.0110 12.9890 0.5113814.00 0.0110 13.9890 0.5507515.00 0.0110 14.9890 0.5901216.00 0.0110 15.9890 0.6294917.00 0.0110 16.9890 0.6688618.00 0.0110 17.9890 0.7082319.00 0.0130 18.9870 0.7475220.00 0.0130 19.9870 0.7868922.00 0.0130 21.987 0.8656325.00 0.0130 24.987 0.98374

Dia.

1-800-999-7346 WWW.REGO-FIX.COMCOL 1061.2 11/12

PG 6 PG 10 PG 15 PG 25 PG 32Tool Dia (D) L L

(min)L

(max)L L

(min)L

(max)L L

(min)L

(max)L L

(min)L

(max)L L

(min)L

(max)0.2-1.0mm 21.5 26.5 20 241.5mm 23.5 26.5 16 202mm 28 24 26.5 28 25 302.5mm 28 24 26.5 28 25 303mm 28 24 26.5 28 25 30 28 25 30 28 25 32.54mm - 5mm 28 25 30 28 25 30 28 25 40.56mm 36 30 35 36 33 38 36 25 40.5 36 33.5 40.97mm - 9mm 36 33 38 36 33 40.5 36 33.5 40.910mm 40 37 40.5 40 37 44.5 40 35.5 44.911mm 40 37 44.5 40 35.5 44.912mm - 14mm 45 42 49.5 45 40.5 49.916mm – 18mm 48 45.5 50 48 43.5 52.920mm 50 47.5 50 50 45.5 54.922mm 50 45.5 54.925mm 56 49.5 58

PG 6 PG 10 PG 15 PG 25 PG 32Tool Dia.(D) L L

(min)L

(max)L L

(min)L

(max)L L

(min)L

(max)L L

(min)L

(max)L L

(min)L

(max)1/16” 0.925” 1.043” 0.630” 0.787”1/8” 1.102” 0.945” 1.043” 1.102” 0.984” 1.181” 1.102” 0.984” 1.181” 1.102” 0.984” 1.280”3/16” 1.102: 0.984” 1.181” 1.102” 0.984” 1.181” 1.102 0.984” 1.594”1/4” 1.417” 1.181” 1.378” 1.417” 1.299” 1.496” 1.417” 1.299” 1.594” 1.417” 1.319” 1.610”5/16” 1.417” 1.299” 1.496” 1.417” 1.457 1.594” 1.417” 1.319” 1.610”3/8” 1.575” 1.457” 1.594” 1.575” 1.457” 1.752” 1.575” 1.398” 1.768”7/16” 1.575” 1.46” 1.752” 1.575” 1.398” 1.768”1/2” -9/16” 1.772” 1.654” 1.949” 1.772” 1.594” 1.965”5/8”-11/16” 1.890” 1.791” 1.969” 1.890” 1.713” 2.083”3/4” 1.969” 1.870” 1.969” 1.969” 1.791” 2.161”7/8” 1.969” 1.791” 2.161”1” 2.205” 1.949” 2.283”

powRgrip Technical Requirementsh6 Shank Tolerances


PG 10 PG 15 PG 25Dia. L L

(min)L

(max)L L

(min)L

(max)L L

(min)L

(max)1/8”, 3/16”

28 24 30 28 25 32 28 25 32

1/4” 33.5 30 35.5 36 33 40 36 33 405/16” 36 33 40 36 33 403/8” 40 37 40.5 40 37 447/16” 40 37 441/2” , 9/16”

45 42 49

5/8” 48 45 503/4” 50 47 50

Fractional Decimal Tolerance Min size1/8 0.125 0.00024 0.12476

3/16 0.1875 0.00031 0.187191/4 0.25 0.00035 0.249655/16 0.3125 0.00035 0.312153/8 0.375 0.00035 0.374657/16 0.4375 0.00043 0.437071/2 0.5 0.00043 0.499579/16 0.5625 0.00043 0.562075/8 0.625 0.00043 0.624573/4 0.75 0.00051 0.749497/8 0.875 0.00051 0.874491.0 1.000 0.00051 0.99949

LDia.

Metric Tolerance Min size Inch Conv.2.00 0.0060 1.9940 0.078503.00 0.0060 2.9940 0.117874.00 0.0080 3.9920 0.157175.00 0.0080 4.9920 0.196546.00 0.0080 5.9920 0.235917.00 0.0090 6.9910 0.275248.00 0.0090 7.9910 0.314619.00 0.0090 8.9910 0.35398

10.00 0.0090 9.9910 0.3933511.00 0.0110 10.9890 0.4326412.00 0.0110 11.9890 0.47201

13.00 0.0110 12.9890 0.5113814.00 0.0110 13.9890 0.5507515.00 0.0110 14.9890 0.5901216.00 0.0110 15.9890 0.6294917.00 0.0110 16.9890 0.6688618.00 0.0110 17.9890 0.7082319.00 0.0130 18.9870 0.7475220.00 0.0130 19.9870 0.7868922.00 0.0130 21.987 0.8656325.00 0.0130 24.987 0.98374

Dia.

1-800-999-7346 WWW.REGO-FIX.COMCOL 1061.2 11/12

PG 6 PG 10 PG 15 PG 25 PG 32Tool Dia (D) L L

(min)L

(max)L L

(min)L

(max)L L

(min)L

(max)L L

(min)L

(max)L L

(min)L

(max)0.2-1.0mm 21.5 26.5 20 241.5mm 23.5 26.5 16 202mm 28 24 26.5 28 25 302.5mm 28 24 26.5 28 25 303mm 28 24 26.5 28 25 30 28 25 30 28 25 32.54mm - 5mm 28 25 30 28 25 30 28 25 40.56mm 36 30 35 36 33 38 36 25 40.5 36 33.5 40.97mm - 9mm 36 33 38 36 33 40.5 36 33.5 40.910mm 40 37 40.5 40 37 44.5 40 35.5 44.911mm 40 37 44.5 40 35.5 44.912mm - 14mm 45 42 49.5 45 40.5 49.916mm – 18mm 48 45.5 50 48 43.5 52.920mm 50 47.5 50 50 45.5 54.922mm 50 45.5 54.925mm 56 49.5 58

PG 6 PG 10 PG 15 PG 25 PG 32Tool Dia.(D) L L

(min)L

(max)L L

(min)L

(max)L L

(min)L

(max)L L

(min)L

(max)L L

(min)L

(max)1/16” 0.925” 1.043” 0.630” 0.787”1/8” 1.102” 0.945” 1.043” 1.102” 0.984” 1.181” 1.102” 0.984” 1.181” 1.102” 0.984” 1.280”3/16” 1.102: 0.984” 1.181” 1.102” 0.984” 1.181” 1.102 0.984” 1.594”1/4” 1.417” 1.181” 1.378” 1.417” 1.299” 1.496” 1.417” 1.299” 1.594” 1.417” 1.319” 1.610”5/16” 1.417” 1.299” 1.496” 1.417” 1.457 1.594” 1.417” 1.319” 1.610”3/8” 1.575” 1.457” 1.594” 1.575” 1.457” 1.752” 1.575” 1.398” 1.768”7/16” 1.575” 1.46” 1.752” 1.575” 1.398” 1.768”1/2” -9/16” 1.772” 1.654” 1.949” 1.772” 1.594” 1.965”5/8”-11/16” 1.890” 1.791” 1.969” 1.890” 1.713” 2.083”3/4” 1.969” 1.870” 1.969” 1.969” 1.791” 2.161”7/8” 1.969” 1.791” 2.161”1” 2.205” 1.949” 2.283”

[Inch] PG6 PG 10 PG 15 PG 25 PG 32

Tool Dia (D)Inch

L L(min)

L(max)

L L(min)

L(max)

L L(min)

L(max)

L L(min)

L(max)

L L(min)

L(max)

1/16 .925 1.043 0.630 0.787

1/8 1.102 0.945 1.043 1.102 0.984 1.181 1.102 0.984 1.181 1.102 0.984 1.280

3/16 1.102 0.984 1.181 1.102 0.984 1.181 1.102 0.984 1.594

1/4 1.417 1.181 1.378 1.417 1.299 1.496 1.417 1.299 1.594 1.417 1.319 1.610

5/16 1.417 1.299 1.496 1.417 1.457 1.594 1.417 1.319 1.610

3/8 1.575 1.457 1.594 1.575 1.457 1.752 1.575 1.398 1.768

7/16 1.575 1.460 1.752 1.575 1.398 1.768

1/2 - 9/16 1.772 1.654 1.949 1.772 1.594 1.965

5/8 - 11/16 1.890 1.791 1.969 1.890 1.713 2.083

3/4 1.969 1.870 1.969 1.969 1.791 2.161

7/8 1.969 1.791 2.161

1 2.205 1.949 2.283

[MM] PG6 PG 10 PG 15 PG 25 PG 32

Tool Dia (D)Metric

L L(min)

L(max)

L L(min)

L(max)

L L(min)

L(max)

L L(min)

L(max)

L L(min)

L(max)

0.2 - 1.0 21.5 26.5 20 24

1.5 23.5 26.5 16 20

2 28 24 26.5 28 25 30

2.5 28 24 26.5 28 25 30

3 28 24 26.5 28 25 30 28 25 30 28 25 32.5

4 - 5 28 25 30 28 25 30 28 25 40.5

6 36 30 35 356 33 38 36 25 40.5 36 33.5 40.9

7 - 9 36 33 38 36 33 40.5 36 33.5 40.9

10 40 37 40.5 40 37 44.5 40 35.5 44.9

11 40 37 44.5 40 35.5 44.9

12 - 14 45 42 49.5 45 40.5 49.9

16 - 18 48 45.5 50 48 43.5 52.9

20 50 47.5 50 50 45.5 54.9

22 50 45.5 54.9

25 56 49.5 58


PG

32COL1116.1 09/2013

Home


Weldon Flats

D

L

BA

D L A B

diainch

dia Dh6 inch mm inch mm inch mm

h1h11 mm

inchmax

inchmin

1/2 12.7000 .890 22.620 0.330 8.380 0.440 11.1760

-.011

11.070 0.440 0.436

5/8 15.875 0.953 24.210 0.400 10.160 0.560 14.224 14.110 0.560 0.556

3/4 19.050 1.016 25.797 0.455 11.557 0.675 17.145 14.040 0.675 0.671

1 25.400 1.141 28.972 0.515 13.081 0.925 23.495 -.013 23.365 0.925 0.920

h6 Shank Tolerances

Metric ToleranceMinimum

SizeInch

Conversion

2.00 0.0060 1.9940 0.07850

3.00 0.0060 2.9940 0.11787

4.00 0.0080 3.9920 0.15717

5.00 0.0080 4.9920 0.19654

6.00 0.0080 5.9920 0.23591

7.00 0.0090 6.9910 0.27524

8.00 0.0090 7.9910 0.31461

9.00 0.0090 8.9910 0.35398

10.00 0.0090 9.9910 0.39335

11.00 0.0110 10.9890 0.43264

12.00 0.0110 11.9890 0.47201

13.00 0.0110 12.9890 0.51138

14.00 0.0110 13.9890 0.55075

15.00 0.0110 14.9890 0.59012

16.00 0.0110 15.9890 0.62949

17.00 0.0110 16.9890 0.66886

18.00 0.0110 17.9890 0.70823

19.00 0.0130 18.9870 0.74752

20.00 0.0130 19.9870 0.78689

22.00 0.0130 21.987 0.86563

25.00 0.0130 24.987 0.98374

Fractional Decimal Tolerance Minimum Size

1/8 0.125 0.00024 0.12476

3/16 0.1875 0.00031 0.18719

1/4 0.25 0.00035 0.24965

5/16 0.3125 0.00035 0.31215

3/8 0.375 0.00035 0.37465

7/16 0.4375 0.00043 0.43707

1/2 0.5 0.00043 0.49957

9/16 0.5625 0.00043 0.56207

5/8 0.625 0.00043 0.62457

3/4 0.75 0.00051 0.74949

7/8 0.875 0.00051 0.87449

1 1 0.00051 0.99949

powRgrip System - Productivity Inc · REGO-FIX’s powRgrip System is a unique collet-holding...

Documents

Transcript of powRgrip System - Productivity Inc · REGO-FIX’s powRgrip System is a unique collet-holding...