PowerPoint Presentation small to be measured and we say the capacitor is fully ... A 1.50-V cell is...
Transcript of PowerPoint Presentation small to be measured and we say the capacitor is fully ... A 1.50-V cell is...
![Page 1: PowerPoint Presentation small to be measured and we say the capacitor is fully ... A 1.50-V cell is connected ... PowerPoint Presentation](https://reader033.fdocuments.in/reader033/viewer/2022051800/5acfa9997f8b9a8b1e8cfa4f/html5/thumbnails/1.jpg)
Charging capacitors Storing energy and charging
Book page 458, 463 - 470
©cg
rah
amp
hys
ics.
com
20
15
![Page 2: PowerPoint Presentation small to be measured and we say the capacitor is fully ... A 1.50-V cell is connected ... PowerPoint Presentation](https://reader033.fdocuments.in/reader033/viewer/2022051800/5acfa9997f8b9a8b1e8cfa4f/html5/thumbnails/2.jpg)
Review • Series
• 𝑉𝑡 = 𝑉1 + 𝑉2 + 𝑉3
• Q is the same
•1
𝐶𝑒𝑞𝑢=
1
𝐶1+
1
𝐶2+
1
𝐶3
• 𝑅𝑒𝑞𝑢 = 𝑅1 + 𝑅2 + ⋯
• Parallel
• 𝑉𝑡 = 𝑉1 = 𝑉2 = 𝑉3
• 𝑄𝑡 = 𝑄1 + 𝑄2 + 𝑄3
• 𝐶𝑒𝑞𝑢 = 𝐶1 + 𝐶2 + ⋯
•1
𝑅𝑒𝑞𝑢=
1
𝑅1+
1
𝑅2+
1
𝑅3
©cg
rah
amp
hys
ics.
com
20
15
𝐶 =𝑞
𝑉
𝐶 = 𝑘𝜀0
𝐴
𝑑
Where k = dielectric constant = 𝜀
𝜀0
𝜀0 = 𝑝𝑒𝑟𝑚𝑖𝑡𝑡𝑖𝑣𝑖𝑡𝑦 𝑜𝑓 𝑓𝑟𝑒𝑒 𝑠𝑝𝑎𝑐𝑒 = 8.9 × 10−12
![Page 3: PowerPoint Presentation small to be measured and we say the capacitor is fully ... A 1.50-V cell is connected ... PowerPoint Presentation](https://reader033.fdocuments.in/reader033/viewer/2022051800/5acfa9997f8b9a8b1e8cfa4f/html5/thumbnails/3.jpg)
Energy changes
• From experimental data a graph of charge q stored on a capacitor vs PD can be drawn
• Q = It
• The result is a straight line with the gradient equal to C
©cg
rah
amp
hys
ics.
com
20
15
![Page 4: PowerPoint Presentation small to be measured and we say the capacitor is fully ... A 1.50-V cell is connected ... PowerPoint Presentation](https://reader033.fdocuments.in/reader033/viewer/2022051800/5acfa9997f8b9a8b1e8cfa4f/html5/thumbnails/4.jpg)
Definition
• PD is the energy per unit charge stored on the plates: 𝑃𝐷 =𝐸
𝑞
• QV = energy stored = Area under the graph
= 1
2× 𝑞 × 𝑉
• QV = 1
2× 𝑞 ×
𝑞
𝐶
• Energy stored = 1
2
𝑞2
𝐶
• Energy stored can be written as 1
2𝐶𝑉2
©cg
rah
amp
hys
ics.
com
20
15
But Q = CV
![Page 5: PowerPoint Presentation small to be measured and we say the capacitor is fully ... A 1.50-V cell is connected ... PowerPoint Presentation](https://reader033.fdocuments.in/reader033/viewer/2022051800/5acfa9997f8b9a8b1e8cfa4f/html5/thumbnails/5.jpg)
Example
• A 6V battery is connected to a 20𝜇𝐹 𝑐𝑎𝑝𝑎𝑐𝑖𝑡𝑜𝑟. Find the energy that can be stored on the capacitor.
• Solution
• E = 1
2𝐶𝑉2
=1
2× 20 × 10−6 × 62
= 3.6 × 10−4𝐽
©cg
rah
amp
hys
ics.
com
20
15
![Page 6: PowerPoint Presentation small to be measured and we say the capacitor is fully ... A 1.50-V cell is connected ... PowerPoint Presentation](https://reader033.fdocuments.in/reader033/viewer/2022051800/5acfa9997f8b9a8b1e8cfa4f/html5/thumbnails/6.jpg)
Resistor – capacitor RC series circuits • In a basic resistor circuit, charge is immediately available to be used
by the resistor and it has a constant value
• 𝐼 =𝑒𝑚𝑓
𝑅
• 𝑄 = 𝐶𝑉
• 𝐼 =𝑄
𝑡=
𝑒𝑚𝑓
𝑅
• In a RC circuit charge is building up over time
©cg
rah
amp
hys
ics.
com
20
15
![Page 7: PowerPoint Presentation small to be measured and we say the capacitor is fully ... A 1.50-V cell is connected ... PowerPoint Presentation](https://reader033.fdocuments.in/reader033/viewer/2022051800/5acfa9997f8b9a8b1e8cfa4f/html5/thumbnails/7.jpg)
What happens in a charging RC circuit
t = 0 𝒕 → ∞ 𝒇𝒖𝒍𝒍𝒚 𝒄𝒉𝒂𝒓𝒈𝒆𝒅
∆𝒕 during charging
𝐼0 =𝑒𝑚𝑓
𝑅
I = 0 𝐼 =
∆𝑄
∆𝑡
𝑉𝑅 = 𝑒𝑚𝑓 𝑉𝑅 = 0
𝑉𝐶 = 0 𝑉𝐶 = 𝑒𝑚𝑓
𝑄𝐶 = 0 𝑄𝐶 = 𝑄𝑓𝑖𝑛𝑎𝑙 = 𝐶 × 𝑒𝑚𝑓
©cg
rah
amp
hys
ics.
com
20
15
• Capacitor starts charging, battery starts to charge the plates • Charge passes through resistor • Circuit carries a changing current • At max value capacitor has charge Q = C x emf • Current in circuit will be zero
![Page 8: PowerPoint Presentation small to be measured and we say the capacitor is fully ... A 1.50-V cell is connected ... PowerPoint Presentation](https://reader033.fdocuments.in/reader033/viewer/2022051800/5acfa9997f8b9a8b1e8cfa4f/html5/thumbnails/8.jpg)
Max charge on capacitor
• Maximum charge on capacitor = capacitance x emf of cell
• The current does not flow through the capacitor
• Why?
• It looks like it is flowing
• During charging: 𝐼𝑐 ↓
𝑉𝐶 ↑ until max emf
©cg
rah
amp
hys
ics.
com
20
15
![Page 9: PowerPoint Presentation small to be measured and we say the capacitor is fully ... A 1.50-V cell is connected ... PowerPoint Presentation](https://reader033.fdocuments.in/reader033/viewer/2022051800/5acfa9997f8b9a8b1e8cfa4f/html5/thumbnails/9.jpg)
What happens at the plates • An electric field is set up between the plates
• But: no electrons flow through the material
Simplify
• 1. electric current – flow of charge and electrons
• 2. displacement current (Maxwell) flows through capacitor new definition
• Charging a capacitor changes the electric field b/w the plates
• It also creates a changing magnetic field with enough energy to move electrons
©cg
rah
amp
hys
ics.
com
20
15
![Page 10: PowerPoint Presentation small to be measured and we say the capacitor is fully ... A 1.50-V cell is connected ... PowerPoint Presentation](https://reader033.fdocuments.in/reader033/viewer/2022051800/5acfa9997f8b9a8b1e8cfa4f/html5/thumbnails/10.jpg)
Charging a capacitor
• Current puts positive charge on capacitor, Q = CV
• Positive charge exerts force that pulls the negative charge
• They babance out
• Galvanometer shows direction
• Electric field E = 0 when start charging and slowly increases in time
©cg
rah
amp
hys
ics.
com
20
15
![Page 11: PowerPoint Presentation small to be measured and we say the capacitor is fully ... A 1.50-V cell is connected ... PowerPoint Presentation](https://reader033.fdocuments.in/reader033/viewer/2022051800/5acfa9997f8b9a8b1e8cfa4f/html5/thumbnails/11.jpg)
Charging continued
• V = Ed
• C = 𝜀𝐴
𝑑
• I = C ×𝑑𝑉
𝑑𝑡= 𝐽𝐴 where J – current density and A = area
• 𝐽𝐴 = 𝜀𝐴
𝑑×
𝑑
𝑑𝑡𝐸𝑑
• 𝐽 = 𝜀 ×𝑑𝐸
𝑑𝑡=
𝑑𝐷
𝑑𝑡, where
𝑑𝐷
𝑑𝑡 = displacement current density,
the rate of change of electric flux vector with time
• This way the current is related to the change of a field ©cg
rah
amp
hys
ics.
com
20
15
![Page 12: PowerPoint Presentation small to be measured and we say the capacitor is fully ... A 1.50-V cell is connected ... PowerPoint Presentation](https://reader033.fdocuments.in/reader033/viewer/2022051800/5acfa9997f8b9a8b1e8cfa4f/html5/thumbnails/12.jpg)
Re-conceptionalize current
• E puts force on molecules
• Negatively charged electron clouds move to positive plate
• Shifting of electron clouds act like a current
©cg
rah
amp
hys
ics.
com
20
15
![Page 13: PowerPoint Presentation small to be measured and we say the capacitor is fully ... A 1.50-V cell is connected ... PowerPoint Presentation](https://reader033.fdocuments.in/reader033/viewer/2022051800/5acfa9997f8b9a8b1e8cfa4f/html5/thumbnails/13.jpg)
Charging plates
• Fill the space with dielectric material
• It contains atoms and molecules
• Even in vacuum an electric flux vector will be set up, which acts exactly like a current is flowing
• This is the displacement current
©cg
rah
amp
hys
ics.
com
20
15
![Page 14: PowerPoint Presentation small to be measured and we say the capacitor is fully ... A 1.50-V cell is connected ... PowerPoint Presentation](https://reader033.fdocuments.in/reader033/viewer/2022051800/5acfa9997f8b9a8b1e8cfa4f/html5/thumbnails/14.jpg)
Graphical interpretation of charging
• 𝐼0 = gradient of graph at origin
• As charge build up, current drops
• At maximum charge, I = 0
©cg
rah
amp
hys
ics.
com
20
15
![Page 15: PowerPoint Presentation small to be measured and we say the capacitor is fully ... A 1.50-V cell is connected ... PowerPoint Presentation](https://reader033.fdocuments.in/reader033/viewer/2022051800/5acfa9997f8b9a8b1e8cfa4f/html5/thumbnails/15.jpg)
Time constant
• In principle, a capacitor can never fully charge because the rate of charging drops as the charge increases
• In practice, after a finite time the charging current becomes too small to be measured and we say the capacitor is fully charged
Definition:
• The time it takes to charge a capacitor in a given circuit is determined by the time constant 𝜏 of the circuit
• 𝜏 = 𝑅𝐶
• The half time 𝑡1
2
is the time taken to halve the charging
current
• 𝑡1
2
= 𝜏 × ln 2 = 𝑅𝐶 ln 2 = 0.693𝑅𝐶
©cg
rah
amp
hys
ics.
com
20
15
![Page 16: PowerPoint Presentation small to be measured and we say the capacitor is fully ... A 1.50-V cell is connected ... PowerPoint Presentation](https://reader033.fdocuments.in/reader033/viewer/2022051800/5acfa9997f8b9a8b1e8cfa4f/html5/thumbnails/16.jpg)
Example • A 250𝜇𝐹 capacitor is being charged from a 6V cell of negligible
internal resistance via a 10kΩ resistor. What is the initial charging current?
• Solution
• 𝐼 =𝑒𝑚𝑓
𝑅=
6
10000= 0.6 × 10−3𝐴 = 0.6𝑚𝐴
• What is the charging current after 10.4s?
• Solution
• 𝜏 = 𝑅𝐶=250 × 10−6 × 10000 = 2.5𝑠
• 𝑡1
2
= 𝜏 × ln 2 = 𝑅𝐶 ln 2 = 0.693𝑅𝐶 = 0.693 × 2.5 = 1.73𝑠
• 𝑛 =𝑡
𝑡12
=10.4
1.73= 5.78~6 ℎ𝑎𝑙𝑓 𝑙𝑖𝑣𝑒𝑠
• Charging current after 6 𝑡1
2
=𝐼0
2𝑛 =0.6×10−3
26 = 9.4𝜇𝐴
©cg
rah
amp
hys
ics.
com
20
15
𝐼 =𝐼0
2𝑛
![Page 17: PowerPoint Presentation small to be measured and we say the capacitor is fully ... A 1.50-V cell is connected ... PowerPoint Presentation](https://reader033.fdocuments.in/reader033/viewer/2022051800/5acfa9997f8b9a8b1e8cfa4f/html5/thumbnails/17.jpg)
Mathematics of charging a capacitor
• Kirchhoff’s 2nd law: Emf = V + IR
• V and I are changing charge on capacitor:
Q = CV or 𝑉 =𝑄
𝐶
• 𝐼 =𝑑𝑄
𝑑𝑡
• This is positive because charge on plates increases with time
©cg
rah
amp
hys
ics.
com
20
15
+q
- q
![Page 18: PowerPoint Presentation small to be measured and we say the capacitor is fully ... A 1.50-V cell is connected ... PowerPoint Presentation](https://reader033.fdocuments.in/reader033/viewer/2022051800/5acfa9997f8b9a8b1e8cfa4f/html5/thumbnails/18.jpg)
Putting it together • Emf= 𝑉 + 𝐼𝑅 =
𝑄
𝐶+ 𝑅
𝑑𝑄
𝑑𝑡
•𝑑𝑄
𝑑𝑡=
𝑒𝑚𝑓
𝑅−
𝑄
𝑅𝐶=
𝑒𝑚𝑓𝐶−𝑄
𝐶𝑅
• Let U = 𝑒𝑚𝑓𝐶 − 𝑄, then emf and C are constants
•𝑑𝑈
𝑑𝑡= −
𝑑𝑄
𝑑𝑡 where
𝑑𝑄
𝑑𝑡=
𝑈
𝐶𝑅
•𝑑𝑈
𝑑𝑡=
𝑈
𝐶𝑅
• Integrating this expression we get
• 𝑈 = 𝑈0𝑒−𝑡
𝐶𝑅
• 𝑈0= value when t = 0
• When t = 0 Q = 0
©cg
rah
amp
hys
ics.
com
20
15
• When t = 0 we get
• 𝑈 = 𝑈0𝑒−𝑡
𝐶𝑅
• emf C – Q =(emfC-0) 𝑒−𝑡
𝐶𝑅
• Q=emfC - emfC 𝑒−𝑡
𝐶𝑅
• Q = emf C(1 - 𝑒−𝑡
𝐶𝑅) • Q = emf C
• Q = 𝑄𝑓𝑖𝑛𝑎𝑙 1 − 𝑒−𝑡
𝐶𝑅
• CR = 𝜏
• Q = 𝑄𝑓𝑖𝑛𝑎𝑙 1 − 𝑒−𝑡
𝜏
![Page 19: PowerPoint Presentation small to be measured and we say the capacitor is fully ... A 1.50-V cell is connected ... PowerPoint Presentation](https://reader033.fdocuments.in/reader033/viewer/2022051800/5acfa9997f8b9a8b1e8cfa4f/html5/thumbnails/19.jpg)
Mathematical skills
• Q = 𝑄𝑓𝑖𝑛𝑎𝑙 1 − 𝑒−𝑡
𝜏
•𝑄
𝑄𝑓𝑖𝑛𝑎𝑙= 1 − 𝑒−
𝑡
𝑅𝐶
• 1 - 𝑄
𝑄𝑓𝑖𝑛𝑎𝑙= 𝑒−
𝑡
𝑅𝐶
• ln 1 − 𝑄
𝑄𝑓𝑖𝑛𝑎𝑙=
ln 𝑒−𝑡
𝑅𝐶 = −𝑡
𝑅𝐶
• 𝑡 = −𝑅𝐶 ln 1 − 𝑄
𝑄𝑓𝑖𝑛𝑎𝑙
• Suppose RC = 5.00s
Q = 1
4 𝑄𝑓𝑖𝑛𝑎𝑙
• The time required for the capacitor to acquire this charge is
• 𝑡 = −𝑅𝐶 ln 1 − 𝑄
𝑄𝑓𝑖𝑛𝑎𝑙
= −5[ln(1 −1
4)] = −5ln
3
4
= -5 x (-0.288) = 1.44s
©cg
rah
amp
hys
ics.
com
20
15
![Page 20: PowerPoint Presentation small to be measured and we say the capacitor is fully ... A 1.50-V cell is connected ... PowerPoint Presentation](https://reader033.fdocuments.in/reader033/viewer/2022051800/5acfa9997f8b9a8b1e8cfa4f/html5/thumbnails/20.jpg)
Example
• The time constant for (A) is 0.20s. What is the time constant for (B)?
• Solution
• Find 𝐶𝑒𝑞𝑢 for each arrangement
• A) 1
𝐶𝑒𝑞𝑢=
1
𝐶+
1
𝐶=
2
𝐶
𝐶𝑒𝑞𝑢 =1
2𝐶
• B) 𝐶𝑒𝑞𝑢 = 𝐶 + 𝐶 = 2𝐶 • Time constant 𝜏𝐴 = 0.20
• 𝜏 = 𝐶𝑅 → 0.20 =1
2𝐶R
©cg
rah
amp
hys
ics.
com
20
15
A
R C C
B
• 𝜏𝐵 = 2𝐶𝑅
•𝜏𝐵
𝜏𝐴=
2𝐶𝑅1
2𝐶R
• 𝜏𝐵 = 4 × 0.20 = 0.80𝑠
![Page 21: PowerPoint Presentation small to be measured and we say the capacitor is fully ... A 1.50-V cell is connected ... PowerPoint Presentation](https://reader033.fdocuments.in/reader033/viewer/2022051800/5acfa9997f8b9a8b1e8cfa4f/html5/thumbnails/21.jpg)
EXAMPLE: Two capacitors are in the circuit
shown. C1 is fully charged at 1.50 V, and C2
is initially uncharged.
(a) What is the electrical energy stored in C1?
(b) What is the charge on C1’s plates?
SOLUTION:
(a) E = 1
2CV 2 = 3.0910-4 J
(b) q = CV = 27510-6(1.50) = 4.12510-4 C.
Solving problems involving parallel-plate capacitors
Example
![Page 22: PowerPoint Presentation small to be measured and we say the capacitor is fully ... A 1.50-V cell is connected ... PowerPoint Presentation](https://reader033.fdocuments.in/reader033/viewer/2022051800/5acfa9997f8b9a8b1e8cfa4f/html5/thumbnails/22.jpg)
EXAMPLE: Two capacitors are in the circuit
shown. C1 is fully charged at 1.50 V, and C2
is initially uncharged.
(c) When the switch is closed, what will the
charge on C1 be? What charge will C2 have?
SOLUTION: The capacitors are in parallel. Thus
V1 = V2 q1
C1
= q2
C2
Thus q2 = C2
C1
×q1.
From conservation of charge, q1 + q2 = 4.12510-4 C.
4.12510-4 = q1 + q2 = q1 + C2
C1
×q1.
= q1 ( 1 + 38275
) q1 = 3.62 10-4 C.
3.62 10-4 + q2 = 4.12510-4 q2 = 5.01 10-5 C.
Example continued
![Page 23: PowerPoint Presentation small to be measured and we say the capacitor is fully ... A 1.50-V cell is connected ... PowerPoint Presentation](https://reader033.fdocuments.in/reader033/viewer/2022051800/5acfa9997f8b9a8b1e8cfa4f/html5/thumbnails/23.jpg)
PRACTICE: A 1.50-V cell is connected
to a 275 F capacitor in the circuit
shown.
(a) Make a sketch graph of what the
voltmeter reads after the switch is closed.
SOLUTION:
Before the switch is closed the
voltage on the capacitor is zero.
After the switch is closed, the
voltage will increase from zero to 1.50 V in a very short
amount of time as the plates store the charge.
Then the capacitor’s voltage will remain at 1.50 V.
Charging a capacitor
V / V
t
1.50
Example
![Page 24: PowerPoint Presentation small to be measured and we say the capacitor is fully ... A 1.50-V cell is connected ... PowerPoint Presentation](https://reader033.fdocuments.in/reader033/viewer/2022051800/5acfa9997f8b9a8b1e8cfa4f/html5/thumbnails/24.jpg)
PRACTICE: A 1.50-V cell is connected
to a 275 F capacitor in the circuit
shown.
(b) Make a sketch graph of what the
ammeter reads after the switch is closed.
SOLUTION:
Before the switch is closed the
current is zero.
After the switch is closed, the
current will begin at a maximum value and will decrease
rapidly as the plates “fill up” with charge and repel
further charge.
Then the current will remain at zero.
Charging a capacitor
I / A
t
MAX
Example continued
![Page 25: PowerPoint Presentation small to be measured and we say the capacitor is fully ... A 1.50-V cell is connected ... PowerPoint Presentation](https://reader033.fdocuments.in/reader033/viewer/2022051800/5acfa9997f8b9a8b1e8cfa4f/html5/thumbnails/25.jpg)
PRACTICE: A 1.50-V cell is connected
to a 275 F capacitor in the circuit
shown.
(c) Make a sketch graph of the charge q
on the plates after the switch is closed.
SOLUTION:
Before the switch is closed the
charge is zero.
After the switch is closed, the
charge will rapidly “fill up” the plates and slow down the
subsequent flow due to repulsion.
Then the charge will reach a maximum value on the
plates, stopping the flow of further charge.
Charging a capacitor
q / C
t
MAX
Example contiuned
![Page 26: PowerPoint Presentation small to be measured and we say the capacitor is fully ... A 1.50-V cell is connected ... PowerPoint Presentation](https://reader033.fdocuments.in/reader033/viewer/2022051800/5acfa9997f8b9a8b1e8cfa4f/html5/thumbnails/26.jpg)
PRACTICE: A 1.50-V cell is connected
in series to a capacitor and resistor.
Make a sketch graph showing the family
of curves representing the voltage across
the resistor after the switch is closed as RC increases.
SOLUTION:
Before the switch is closed the
current is zero.
After the switch is closed, the current will begin at a
maximum value and will decrease rapidly as the plates
“fill up” with charge and repel further charge.
Then the current will remain at zero.
RC series circuits – charging
I / A
t
MAX
Example
C
R
![Page 27: PowerPoint Presentation small to be measured and we say the capacitor is fully ... A 1.50-V cell is connected ... PowerPoint Presentation](https://reader033.fdocuments.in/reader033/viewer/2022051800/5acfa9997f8b9a8b1e8cfa4f/html5/thumbnails/27.jpg)
PRACTICE: A 1.50-V cell is connected
in series to a capacitor and resistor.
Make a sketch graph showing the family
of curves representing the voltage across
the resistor after the switch is closed as RC increases.
SOLUTION:
Because the voltage across
the resistor is proportional to
the current (V = IR), its graph will have the same shape
as I:
Furthermore, the bigger R and
C are, the longer it will take for
the capacitor to charge and the current to stop.
RC series circuits – charging
I / A
t
MAX
V / V
t
1.50
low RC
medium RC high RC
Example
C
R