Power Connection Options

1

+

-

ground

Updated 9/19/2016Updated 10/11/2017 (DCN 2560)

Released 1/22/2016

Power Connection Options

24v Connection

ICS 3 and ICS 3S Connection

ICS 2 Connection

24 Volt lights are built with flying leads and have load limiting resistors for use with any regulated 24 volt DC power source.

Inline Current Source built into the power cable.

Requires 24v power source

24Flying/tinned leads

Powered with:24V power supply

5Flying/tinned leads


ICS 3 (I3)Combination strobe/continous in-line controller


ICS 3S (I3S)Default-OFFstrobe/continous in-line controller


ICS 2 (IC) Continous in-line controller


+-

gate -0-10V Analog

Inline Current Source built into the power cable.

Requires 24v power source

Default off for ICS3 S version

5v Connection

5 Volt lights are built with flying leads and have load limiting resistors for use with any regulated 5 volt DC power source.

+

-

trigger+ (active HIGH)

Not used

Analog Dimming

ICS 2

ICS 3 and 3S

+

-

ground

2Updated 9/19/2016Updated 10/11/2017 (DCN 2560)

Released 1/22/2016


For Use With:CS100, CS100-IC, CS300, CS300-IC, CS410, CS420,MS210, MS220S4000, S6000, S6000-AS

C2 Connection

C5 Connection

C1 Connection

M12 Add On Connection

For Use With:24v, ICS 2, and ICS 3 wiring

C1 ConnectorFor use with:DCS SeriesControllers

C2 ConnectorFor use with:Legacy Controllers

(Not recommended for new applications)

C5 ConnectorFor use with:Pulsar 320 StrobeController.

For Use With:

For Use With:

3Updated 9/19/2016Updated 10/11/2017 (DCN 2560)

Released 1/22/2016


ICS 2 Specifications

5 Pin

5 Pin

Dimensional Information

M12 Connector Pin-OutMale end view. Ai lights are built with the male connector standard.

PIN COLOR DESC.

DIMENSIONS IN MM

1 BROWN +24V IN2 WHITE Not used3 BLUE -24V IN4 BLACK ACTIVE HIGH5 GRAY Analog Dimming, 0-10V

ICS 2

ICS 3

4 Pin24 Volt

2

4

1

53

PIN COLOR DESC.

1 BROWN +24V IN2 WHITE 0-10V ANALOG3 BLUE -24V IN4 BLACK GATE ACTIVE LOW5 GRAY Not Connected

2

4

1

53

PIN COLOR DESC.


2

4

1

53

0.471 0.810

0.390

2.362

Connection Diagram

4

Power Connection OptionsICS 2 Wiring Diagrams


Released 1/22/2016

BROWN

BLUE

+24VDC

WHITE

BLACK

ACTIVE LOW GATE

GND

NPN

GND

4.7K

TRIGGER

LOW TRIGGER SHUTS LIGHT OFF

BROWN

BLUE

+24VDC

WHITE

BLACK

ACTIVE HIGH GATE

GND

PNP

GND

4.7K

TRIGGER

HIGH TRIGGER SHUTS LIGHT OFF

BROWN

BLUE

+24VDC

WHITE

BLACK

0-10V ANALOG CONTROL

GND

GND

0-10V ADJUST.

LINEAR OUTPUT ADJUST WITH EXTERNAL POTENTIOMETER

5K

0-10V ANALOG CONTROLLINEAR OUTPUT ADJUST

BROWN

BLUE

+24VDC

WHITE

BLACK

GND

GND

0-10V ADJUST.

STANDARD OPERATIONLIGHT IS ALWAYS ON

BROWN

BLUE

+24VDC

WHITE

BLACK

GND

BROWN

BLUE

+24VDC

WHITE

BLACK

ACTIVE LOW GATE

GND

NPN

GND

4.7K

TRIGGER


BROWN

BLUE

+24VDC

WHITE

BLACK

ACTIVE HIGH GATE

GND

PNP

GND

4.7K

TRIGGER


BROWN

BLUE

+24VDC

WHITE

BLACK


GND

GND

0-10V ADJUST.


5K


BROWN

BLUE

+24VDC

WHITE

BLACK

GND

GND

0-10V ADJUST.


BROWN

BLUE

+24VDC

WHITE

BLACK

GND

BROWN

BLUE

+24VDC

WHITE

BLACK

ACTIVE LOW GATE

GND

NPN

GND

4.7K

TRIGGER


BROWN

BLUE

+24VDC

WHITE

BLACK

ACTIVE HIGH GATE

GND

PNP

GND

4.7K

TRIGGER


BROWN

BLUE

+24VDC

WHITE

BLACK


GND

GND

0-10V ADJUST.


5K


BROWN

BLUE

+24VDC

WHITE

BLACK

GND

GND

0-10V ADJUST.


BROWN

BLUE

+24VDC

WHITE

BLACK

GND

BROWN

BLUE

+24VDC

WHITE

BLACK

ACTIVE LOW GATE

GND

NPN

GND

4.7K

TRIGGER


BROWN

BLUE

+24VDC

WHITE

BLACK

ACTIVE HIGH GATE

GND

PNP

GND

4.7K

TRIGGER


BROWN

BLUE

+24VDC

WHITE

BLACK


GND

GND

0-10V ADJUST.


5K


BROWN

BLUE

+24VDC

WHITE

BLACK

GND

GND

0-10V ADJUST.


BROWN

BLUE

+24VDC

WHITE

BLACK

GND

BROWN

BLUE

+24VDC

WHITE

BLACK

ACTIVE LOW GATE

GND

NPN

GND

4.7K

TRIGGER


BROWN

BLUE

+24VDC

WHITE

BLACK

ACTIVE HIGH GATE

GND

PNP

GND

4.7K

TRIGGER


BROWN

BLUE

+24VDC

WHITE

BLACK


GND

GND

0-10V ADJUST.


5K


BROWN

BLUE

+24VDC

WHITE

BLACK

GND

GND

0-10V ADJUST.


BROWN

BLUE

+24VDC

WHITE

BLACK

GND

5


ICS 2 Wiring Diagram for Optional Manual Intensity Control

Note: The MP-iCS is compatible only with lights built with the IC wiring option after 3/1/2012. It cannot be used with 24v lights, or the iCS 1.0

ICS 3/3S Specifications

Parameter Specification Notes

Strobe output

Current Output Adj.

Max. Input Current

Trigger

Input Voltage Range

Active HI: BLACK

Mechanical & Environmental

Storage Temperature

Operating Temperature

Housing Material

Weight

Size

+18 to 30 VDC

0 - 12A* * Pulse-width/Light head dependent

Min to Max Current adj. as established by factory setting

Maximum current set assuming 300µSec operation

1.1A

Active HI: BLACK

-40 to +125C

0 to +70C

High Impact Polycarbonate

Approx 1.7 oz

Approx 4.55L x 0.67W x 0.70H

Approx 100mA local

TTL compatible, 30VDC tolerant

Cable Not Included

Inches

24V nominal

Mode Select Bypass triggering mode

Max. Repetition Rate 100 Hz ** ** Light head dependent

BROWN

BLUE

WHITE

BLACK

GRAY

VIN +

VIN -

Not used

Active HIGH trigger input

ICS PINOUT

Analog dimming, 0-10V


Released 1/22/2016

MP-ICS Manual Dimming Control Wiring Diagram for ICS 2All connections are made at the input

6

Power Connection OptionsICS 3/3S Wiring Diagrams


Released 1/22/2016

+24V BROWN (PIN 1)GND BLUE (PIN 3)ANALOG GRAY (PIN 5)

i3

TYPICAL CONNECTION - CONTINUOUS USE

Light is on continuous when power is applied.Analog control is optional for remote dimming (0-10VDC)

+24V BROWN (PIN 1)GND BLUE (PIN 3)TRIGGER+ BLACK (PIN 4)

i3

TYPICAL CONNECTION - STROBE MODE

Light is on continuous when power is applied. The first trigger pulse will initiate STROBE MODE. The controller remains in STROBE MODE until the power is toggled.

Output light pulse width always follows the duration of the input trigger width.

A period of overdrive occurs within 5msec from the beginning of the pulse. After this period of time, the on-time of the pulse is at the continuous output level.

ANALOG GRAY (PIN 5)

WIRING INFORMATION 5-30VDC

i3 / BLACK / PIN 4

i3 / BLUE / PIN 3

*

*External resistors may not be neededCheck documentation on I/O for recommendations and voltage limits

OFF

ON

GNDI/O

PNP / SOURCING

5-30VDC

i3 / BLACK / PIN 4

i3 / BLUE / PIN 3

*


OFF

ON

GNDI/O

NPN / SINKING

The i3 does not have a true sinking input.The emitter must be tied to the trigger as shown

i3 / GRAY / PIN 5

i3 / BLUE / PIN 3

GND

Analog Dimming: 0 = 10%, 10 = 100% outputAnalog dimming works in both strobe and continuous

1-10VDC

WIRING DIAGRAMS

ADAPTIVE OVERDRIVE™ DIAGRAM

7

Power Connection OptionsICS 3/3S Wiring Diagrams


Released 1/22/2016

+24V BROWN (PIN 1)GND BLUE (PIN 3)ANALOG GRAY (PIN 5)

i3

TYPICAL CONNECTION - CONTINUOUS USE

Light is on continuous when power is applied.Analog control is optional for remote dimming (0-10VDC)

+24V BROWN (PIN 1)GND BLUE (PIN 3)TRIGGER+ BLACK (PIN 4)

i3

TYPICAL CONNECTION - STROBE MODE

Light is on continuous when power is applied. The first trigger pulse will initiate STROBE MODE. The controller remains in STROBE MODE until the power is toggled.

Output light pulse width always follows the duration of the input trigger width.

A period of overdrive occurs within 5msec from the beginning of the pulse. After this period of time, the on-time of the pulse is at the continuous output level.

ANALOG GRAY (PIN 5)

WIRING INFORMATION 5-30VDC

i3 / BLACK / PIN 4

i3 / BLUE / PIN 3

*


OFF

ON

GNDI/O

PNP / SOURCING

5-30VDC

i3 / BLACK / PIN 4

i3 / BLUE / PIN 3

*


OFF

ON

GNDI/O

NPN / SINKING

The i3 does not have a true sinking input.The emitter must be tied to the trigger as shown

i3 / GRAY / PIN 5

i3 / BLUE / PIN 3

GND

Analog Dimming: 0 = 10%, 10 = 100% outputAnalog dimming works in both strobe and continuous

1-10VDC

WIRING DIAGRAMS

ADAPTIVE OVERDRIVE™ DIAGRAM

8


M12 Connector Pin-Out

5 Pin

5 Pin

Dimensional Information

M12 Connector Pin-OutMale end view. Ai lights are built with the male connector standard.

PIN COLOR DESC.

DIMENSIONS IN MM

1 BROWN +24V IN2 WHITE Not used3 BLUE -24V IN4 BLACK ACTIVE HIGH5 GRAY Analog Dimming, 0-10V

ICS 2

ICS 3

4 Pin24 Volt

2

4

1

53

PIN COLOR DESC.


2

4

1

53

PIN COLOR DESC.


2

4

1

53

0.471 0.810

0.390

2.362


Released 1/22/2016

9


This product was tested and complies with the regulatory requirements and limits for electromagnetic compatibility

(EMC) as stated in the product specifications. These requirements and limits are designed to provide reasonable

protection against harmful interference only when the product is operated in its intended industrial electromagnetic

environment. To minimize the potential for electromagnetic interference or unacceptable performance degradation,

install and use this product in strict accordance with the instructions in the product documentation.

Every Advanced illumination, Inc. (Ai) product is thoroughly inspected and tested before leaving the factory.

Products are warranted to be free of defects in workmanship and materials for a period of two years from the

original date of purchase. Should a defect develop during this period, please contact Ai Customer Service or your

Ai distributor for a Return Merchandise Authorization (RMA), and return the complete product, freight prepaid, to Ai.

If a defect is found, Ai will - at our discretion - repair or replace the product without charge. Ai claims no liability for

any implied warranties, including “merchantability” and “fitness for a specific purpose.”

For information on existing orders, or to make an order adjustment, contact us Monday through Friday 8:00 am to

5:00 pm, EST or send an email to [email protected].

Warranty Information

Electromagnetic Compatibility

Customer Service

Company Information

Advanced Illumination

Email: [email protected] Web: advancedillumination.com © 2015 Advanced Illumination Inc. All rights reserved

440 State Garage Road, Rochester VT. 05767

Phone: 802.767.3830

Fax: 802.767.3831


Released 1/22/2016

Power Connection Options

Documents

Transcript of Power Connection Options