Posh Domaine Close Coupled Back to Wall Rimless Toilet ...€¦ · Wall. 40mm. 65 220 745 100-200...
Transcript of Posh Domaine Close Coupled Back to Wall Rimless Toilet ...€¦ · Wall. 40mm. 65 220 745 100-200...
Installation Instructions
Posh Domaine Close Coupled Back to Wall Rimless Toilet Suite with Soft Close Seat White (4 Star)
Plumbers, please ensure a copy of the installationinstructions is left with the end user for future reference
CLEANING RECOMMENDATIONS
We recommend the use of soapy water or approved cleaners. This product should not be cleaned with abrasive materials. Damage caused by any improper treatment is not covered by the product warranty - refer to Warranty Conditions
Set-Up
1. Rough in positions of water inlet,waste outlet and fixing bracketholes. Ensure inlet connectionextends 40mm from finished wall. Prepare waste outlet accordingto required setout (100mm min -200mm max) and drill floor fixingbrackets into position (40mm insidetraced mark of pan rim).
2. Insert top-fix plastic fixing nut andbolt into pan (supplied).
S-Trap Installation1. Lubricate the rubber fins of the pan
bend and position in the waste pipeat the required height. Fix the panconnector back to the wall usingthe rod and bracket.
2. Align and push pan back to wall,connect pan spigot into waste bendensuing firm connection.
3. Fix cistern onto pan, bucket flushand check for leaks.
Water Inlet & Levelling Pan1. Connect rear water inlet valve
using 15mm mini cistern stop supplied. Fill the cistern and ensure correct water level. For adjustment refer separate inlet valve instructions.
2. Ensure that pan is level and thatcisterns aligns with wall. Makeminor adjustments if necessary.
3. Fix pan to floor using screws andcaps provided.
4. Silicone pan to floor. Removeexcess sealant.
65
220
750
100-200
Water Inlet
180
40
185mm
100-200mmset out range
NOTE: Ensure back inlet connection extends 40mm from finished wall
Back Inlet Connection
Finished Wall
40mm
100-200
NOTE: Ensure back inlet connection extends 40mm from finished wall
Back Inlet Connection
Finished Wall
40mm
65
220
745
100-200
Water Inlet
185
40
185mm
100-200mmset out range
NOTE: Ensure back inlet connection extends 40mm from finished wall
Back Inlet Connection
Finished Wall
40mm
65
220
745
100-200
Water Inlet
185
40
185mm
100-200mmset out range
NOTE: Ensure back inlet connection extends 40mm from finished wall
Back Inlet Connection
Finished Wall
40mm
PUSH BUTTON ASSEMBLY AND ADJUSTMENT
12
Loosen lock nutTighten lock nut
Adjustment
Lock out
Full flush
Half flush
Ensure button rods are aligned with full & 1/2 flush on outlet valve.
65
220
745
100-200
Water Inlet
185
40
185mm
100-200mmset out range
NOTE: Ensure back inlet connection extends 40mm from finished wall
Back Inlet Connection
Finished Wall
40mm
INSTALLATION INSTRUCTIONS- BACK INLET
Published 24/06/2020
Installation Instructions
Posh Domaine Close Coupled Back to Wall Rimless Toilet Suite with Soft Close Seat White (4 Star)
INSTALLATION INSTRUCTIONS- BOTTOM INLET
220 40
180
100-200220
220
Water Inlets
Left Hand or Right Hand Water Inlet
185mm
60
100-200mmset out range
Set-Up
Rough in positions of water inlet, waste outlet and fixing bracket. Prepare waste outlet according to required setout (100mm min - 200mm max) and drill floor fixing brackets into position (40mm inside traced mark of pan rim).
1. Insert top-fix plastic fixing nut and boltinto pan (supplied).
S-Trap Installation1. Lubricate the rubber fins of the pan
bend and position in the waste pipeat the required height. Fix the panconnector back to the wall using the rodand bracket.
2. Align and push pan back to wall,connect pan spigot into waste bendensuring firm connection.
3. Fix cistern onto pan, bucket flush andcheck for leaks.
Water Inlet & Levelling Pan1. Connect water inlet valve using 15mm
mini cistern stop and 15mm flexibleconnector (not supplied). Fill the cisternand ensure correct water level. Foradjustment refer separate inlet valveinstructions.
2. Ensure that pan is level and thatcisterns aligns with wall. Make minoradjustments if necessary.
3. Fix pan to floor using screws and capsprovided.
4. Silicone pan to floor. Remove excesssealant.
CLEANING RECOMMENDATIONS
We recommend the use of soapy water or approved cleaners. This product should not be cleaned with abrasive materials. Damage caused by any improper treatment is not covered by the product warranty - refer to Warranty Conditions
PUSH BUTTON ASSEMBLY AND ADJUSTMENT
12
Loosen lock nutTighten lock nut
Adjustment
Lock out
Full flush
Half flush
Ensure button rods are aligned with full & 1/2 flush on outlet valve.
Plumbers, please ensure a copy of the installation instructions is left with the end user for future reference
Published 24/06/2020