Portable Rail Plant Hire - Torrent Trackside · Portable Rail Plant Hire. Torrent Trackside is the...
Transcript of Portable Rail Plant Hire - Torrent Trackside · Portable Rail Plant Hire. Torrent Trackside is the...
Torrent TracksideRailway Plant. Railway People.
24hr helpline0845 769 7168
Setting Hire Standards
Portable RailPlant Hire
Torrent Trackside is the leading railplant hire company in the UK. Ourcustomers benefit from:
l 12 depots giving a full UK wide coverage
l A wide range of the industry’s most innovative equipment
l The most compliant and safety focussed business in the sector
l A near 100% reliability record
l Professional service from dedicated rail industry experts
If you demand value, innovation andreliability from your portable rail planthire speak to Torrent Trackside now.
Torrent TracksideRailway Plant. Railway People.
Keeping you on track
24/7/365...
Contents
Page No.
About Torrent Trackside 4
Portable Rail Maintenance Equipment List
Chainsaws and Brushcutters 10
Impact and Torque Wrenches 13
Stressing Equipment 15
Lighting 18
Lifting and Shifting 25
Clip Applicators and Extractors 32
Wireless Communications 36
Cutting and Grinding Equipment 38
Rail Disk Cutters 40
Rail Drilling 42
Diesel and Petrol Generators 47
Hand and Ballast Tools 49
Ballast Tamping 50
Warning and Safety Equipment 54
Welding and Brazing 56
Cold Expansion and Huck Bolt 57
HIREpod 59
Further Information
VP Plc 59
Torrent Trackside website 63
Codes
London Underground approved item
Product can be operator supplied
NEW
Full national coverage
1 Glasgow 7 Bristol
2 Carlisle 8 Tottenham
3 Durham 9 Romford
4 Bolton 10 Ruislip
5 Rotherham 11 Ashford
6 Lichfield 12 Eastleigh
1
5
2
4
6
9
1011
8
12
3
7
Torrent Trackside employs over 300 people and
our depot network is continually expanding to
provide a full national coverage. This means we
can deliver goods where you need it, when you
need it. Our current depot locations are listed
below:
64
Safety is at the coreof our business
Torrent Trackside is one of the most compliant and
safety focussed businesses in the rail sector, it is
our policy to develop a health and safety culture
throughout the organisation which is committed to
the prevention of injuries and ill health of our
employees and associates.
People are ours and your key resource, we believe
that excellent health and safety standards will
contribute towards their development and lead to
excellent business performance.
Accordingly, we provide financial and physical
resources to support quality and training initiatives
aimed at continuous improvement of our
management systems, in which health and safety
objectives are regarded by all as an integral part of
our overall business strategy.
65
Specialists in operatorsupplied plant hire
Benefits:l Safe and efficient operation
l Eliminate operator negligence
l Minimise breakdown response time with
the combination of an operator / fitter
l Possession overrun risk minimised
Operated Plant Offerings:l Single/Double/Triple Wacker Plates
l Pandrol MK4 Clipping Machine
l Cembre PCM - 2P/FC Fastclip / E-Clip
Applicator/Extractor
l Cold Bolt Expansion equipment (CBX)
l Geismar EGO 4 (RMMM) Personnel Carrier
l Geismar AP11 and AP21 Pandrol fastclip
Applicator/Extractor
Look out for theoperator supplied logoin the product directory
66
Near 100% reliabilityrecord
Maximising uptime and boosting productivity
Torrent Trackside prides itself on maintaining our own
assets to the highest standard achieving a reliability
record of 99.8%. Because of this, customers have
asked Torrent Trackside to maintain and repair their
own plant equipment.
l Fleet of fully equipped service vehicles with
specialist testing facilities.
l Dedicated team of highly skilled and experienced
Engineers with PTS Certification who are regularly
assessed to A1 standards.
l On site repair and maintenance.
l On site portable appliance testing.
l National coverage.
l 24 hour call out facility.
l Programmed service regimes, tailored to suit
individual customer requirements.
l Link up qualified.
67
Experts in tracksideand tunnel lighting
l We ensure that poor visibility isn’t a
contributory factor in accidents
l Our experienced Lighting Supervisors control the contract from start to finish
l The lighting set up is installed by our PTS Certified Staff
l This lighting solution can be installed prior to the possession to speed up access to
the tracks and maximise productivity
l Maintain and modify the lighting as required during the shift to ensure safe
working
l Vast experience with tunnel and underground lighting
l Particular expertise with power generation solutions that support the ventilation of
the tunnels
68
OHL Hire Equipment
Torrent Trackside is the leading supplier of OHL hire
equipment. Our national network, skilled expertise
and exacting standards of maintenance means you
get the job done quickly and on time.
To request a brochure call our 24 hour helpline on
0845 769 7168
69
Torrent Trackside
Railway Plant. Railway People.
24hr helpline
0845 769 7168
www.torrent.co.uk
Torrent TracksideRailway Plant. Railway People.
24hr helpline0845 769 7168
610
A powerful grass and brush cutter designed todeal with the toughest of challenges. A power-ful engine with relatively low weight, themachine has an extra long and angled shaft toallow for a wider sweep. A ‘LowVib’ vibrationdamping system isolates the engine,transmission and cutting attachment toeffectively reduce vibration levels in bothhandles, and any other parts that may come incontact with the operator. A rugged harness andoffset handlebar with angled handles provideeven more comfortable ergonomics. Tilt androtate handlebars simplify transport and storage.
Specification
Item code: 01-006
Power Source: 2 stroke engine
Noise Level (Max): 114dBA
Vibration: 2.5M/s2
Weight: 10.0kg
Power: 1.8kW (2.4hp)
Specification
AccessoriesCode Description Weight Vibration13-010 Safety Kit 1.0kg N/A13-009 Hedge Trimmer (Petrol) 5.0kg 13.0M/s2
Consumables21-051 2-Stroke Oil (100ml) 1.0kg per litre21-003 Petrol 1.0kg per litre
7” Brush CutterStrimmer
611
Chainsaws a
nd Brush Cu
tters
A versatile, lightweight machine used forchiselling and scaling. The lightest Hilti breaker,allows effortless use in all working directions.Its compact design and ergonomic rubberforward grip for easy handling and freedom ofmovement. The TE300 has (AVR) ActiveVibration Reduction making the tool less tiringto use.
This unit has the following applications:
l Remove concrete surface imperfections
l Removing tiles and plaster
l Light chiselling on brick/block, corrective chiselling/finishing on concrete
l Exposing reinforcing bars for concrete repair work
l Removing paint and rust from steel (using theneedle adaptor)
l Cleaning scaffolding (using needle adapter)
Item code: 15-010
Power Source: 110v electric
Single impact energy: 3v
Hammer speed: 4080 (bls/min)
Weight: 3.75kgPower: 8.5kW
Consumables21-820 Replacement needle set
Specification
Hilti 110v Needle GunTE300
612
A powerful saw with very efficient power/weight ratio. The unit has an ergonomicallydesigned handle, slim body with a high centreof gravity, filtered air injection and low vibrationcharacteristics.
SpecificationItem code: 13-001
Power Source: 2 stroke engine
Noise level (max): 118dBA
Chain pitch: 3/8th inch
Vibration: 6.0M/s2
Chain pitch: 3/8th inch
Weight: 6.4kg
Power: 3.6kW
Bar length: 20inch
Specification
AccessoriesCode Description Weight13-012 Extra Chain 0.3kg13-010 Safety Kit 1.0kg
Consumables21-051 2-Stroke Oil (100ml) 1.0kg per litre21-003 Petrol 1.0kg per litre
Husqvarna 365xtorq2 Stroke Chain Saw
613
A lightweight machine for tightening andloosening bolts or nuts, driving in and removingchair screws and when using an adaptor chuck,for augering. Uses impact sockets and augerbits.
There is also a foot rest for added stability whenpull starting and an anti-scuff plate fitted to thefuel tank base. For details of handheld andother wrenches see below.
Specification
Item code: 02-001
Power Source: 2 stroke engine
Engine capacity: 56cc
Size (length/height/width): 590/270/460mm
Torque (adjustable): 350-600ft/lb
1” standard square drive
Weight: 20kg
Specification
Other wrenchesCode Description Weight02-004 Torque Wrench (hand held 650ft/lb) 12.0kg02-005 Impact Wrench (electric 1/2” drive) 11.0kg02-009 Torque Wrench (3/4” drive) 12.0kg
Consumables21-448 Impact Wrench Pin 0.1kg21-449 Impact Wrench Ring 0.1kg
Impact a
nd To
rque Wrenches
Maxim Master 35Impact Wrench
614
The Geismar TB2 Rail Mounted Impact Wrench isa machine specifically designed for heavy dutycoachscrew and fishbolt fastening and can bediesel or petrol powered
Quick switching from coachscrew to fishboltsposition and vice versa can be achieved in aslittle as 15 seconds.
The TB2 also features two socket rotationspeeds, an adjustable torque limiting devicewith graduated dial for direct reading of thetightening torque.
Specification
Item code: 02-002
Socket rotation speeds: 70/195;70/225rpm
Size (length/height/width): 2000/620/880mm
Vibration: 6.0M/s2
Weight trolley: 35kg
Without trolley: 108-141kg*
Torque controller: 28kg
Total weight: 176kg
*Depending on engine type
Specification
Consumables21-448 Impact Wrench Pin 0.1kg21-449 Impact Wrench Ring 0.1kgFull range of sockets available on request
Geismar TB2 RailMounted Impact Wrench
615
The roller system is a revolutionary new productwhich is safer and faster than the traditionalfastclip rollers. They are used to lift and guidethe rail during the stressing process.
We also offer a complete range of stressingequipment, see table below.
Specification
Code Description Weight
04-023 1/2 Stressing Set 282.0kg
04-003 Double Power Pack 63.5kg
04-009 Rail Creeper Adjuster (Hydraulic) 30.0kg
04-010 Rail End Straightener (Hydraulic) 231.0kg
04-019 Under Roller (E Clip) 0.6kg
04-020 Under Roller (E Clip) 0.6kg
04-029 Side Roller G44 UIC60 (Fastclip) 1.0kg
04-030 Side Roller F41 (Fastclip) 1.0kg
04-031 Side Roller F41 (Fastclip) 1.0kg
04-040 Vortok Rollers (Fastclip) 1.0kg
04-044 Vortok Rollers (E Clip) 1.0kg
Fast ClipItem code: 04-040
Stressin
g Eq
uipment
616
Self contained, hydraulically operated, the unit iscapable of either pushing or pulling rail endswith a force of up to 300Kn. The unit grips thehead of the rail, leaving access to removefishplates, and replace insulating end posts,whilst still holding any tension or compressionpresent in the rail.
We also offer a complete range of stressingequipment, see page 15
The Permaquip Rail Creep Adjuster is foradjusting gaps in jointed track withoutdamaging the rail ends. Hydraulically operated,the unit is able to push or pull lengths of railand is obstructionless.
Rail Gap AdjusterItem code: 04-022
Rail Creep AdjusterItem code: 04-009
617
Half hydraulic stressing kits are available for hirewith lightweight stressor powerpacks. Theyprovide control for accurate stressing of CWR inall weather conditions and are available withinsulated tie rods and extended rods formultiple welding.
We also offer a complete range of stressingequipment, see page 15
Used to power stressing equipment. The Pumpis subject to a 12 monthly load test or record ofthorough examination. Double packs can onlyoperate one half set of stressing at a time. Thecouplings fitted are of a quick release screw fittype. This differs from the cold expansioncouplers to remove any possibility of the coldexpansion power pack, which is rated at ahigher pressure rating (10,000psi) being usedto power the stressing kit.
Permaquip HSM Stressor UnitItem code: Various
Stressing Kit Power PackItem code: 04-003
Stressin
g Eq
uipment
618
The LED version of the Aurora Floodlight ispowered by 12 LEDs giving up to 30 hours ofcontinuous daylight-quality, shadow free light(equivalent to 500W halogen).
Choice of three light levels – 6, 18 or 30 LEDs.
Specification
Item code: 06-131
Charging source: Mains and 12v
Operating temp: -40ºc to +60ºc
Light output:: up to 4000 lumens
Height: 550mm
Height folded: 290mm
Width: 264mm
Weight: 8.5kg
Specification
Aurora Floodlight LED
619
Superior to halogen, this unit runs cool giving upto 12 hours continuous daylight-quality, shadowfree light (equivalent to 300W halogen).
The Aurora Floodlight is completely waterproofwith safe operation in all weathers and extremeconditions.
The unit recharges in 6-7 hours and will runcontinuously for 10-12 hours. Recharging is viamains or 12v recharging using special anti-theftcharging leads.
Efficient running provides significant carbonfootprint and cost reduction benefits.
Specification
Item code: 06-008
Charging source: Mains and 12v
Operating temp: -40ºc to +60ºc
Light output: 2000 lumens
Height: 550mm
Height folded: 290mm
Width: 264mm
Weight: 8.7kg
Specification
Aurora Floodlight
Lightin
g
The powerful 1000 W metal halide lamp offersmaximum brightness without glare. That makesit particularly suitable for building sites.
The diffused light from the balloon reducesshadows and contrast for bright, clearillumination.
The actual balloon is constructed from a specialfoldable and durable material. The balloon doesnot need to be blown up. It is held open bymetal supports.
Specification
Item code: 06-13
Charging source: 120v
Operating temp: -25ºc to +40ºc
Light output: 1000 watts
Height: 711mm
Diameter: 1000mm
Lamp type: metal halide
Weight: 25kg
Specification
Wacker Light Balloon
620
Portable yet powerful the Night Searcher galaxyPro can run for up to 8 hours from a singlecharge from it’s Li-ion rechargeable battery.The emains recharger stores neatly in therear of the light.
The lamp can be angled up to 90 degrees andcomes with a handy fold down carrying handle.
Specification
Item code: 06-092
Charging source: 7.4v battery
Light beam: 15m flood beam
Light output: 1750-3500 lumens
Height: 310mm
Depth: 285mm
Width: 350mm
Weight: 1.5kg (inc. charger)
Specification
Night SearcherGalaxy Pro Light
Lightin
g
621
622
All machines are road towable flood lightsystems. Each machine has 4no 1000watt metalhalide lighting heads which are able to extendto over 9 metres (30 feet), which is enough tolight up an area of 7 acres. The units have anoptional power tilt light head system allowingtotal control over the light output even whenthe mast is fully deployed. Each unit can run forup to 60 hours continuous with the unit capableof running up to 85 hours.
l 9m vertical action hydraulic mast height
l 360˚ mast rotation
l Fully automated mast erection in only 12 seconds
l 4 x 1000W Metal Halide lamps
l 130 litre tank, 85 hour-run
l Bio-degradable oil in hydraulic system
l Engine fluids bunded 120%
l Mast deployment alarm and safety system – release park brake and mast descends automatically
l Road lights and reflectors fitted as standard
l Fork pockets & single lift eye
l Easy access fuel fill & sight gauge facility
l Emergency stop
Specification
Item code: 06-036
Weight: 1050kg
Specification
Mobile Lighting Towers
623
Used to light up long lines of work area. Eachunit uses 72w of power meaning you can link32 per 3kva generator. Ideal for work site oraccess lighting.
l Lighting can be supplied and installed by our P.T.S. Certified Staff. Fully trained Lookout and COSS’s are also available.
l Ground spikes, lay-flat ballast baskets or platform tripods are available to suit individual needs.
l Lighting and equipment can be installed prior to the night of the job.
l Our staff maintain and modify the lighting as required during the shift to ensure safe working
l Site engineers are available for the duration of the shift.
l After the shift Torrent Trackside will dismantle, remove, or make safe all lighting as required.
SpecificationSpecification
Trackside Fluorescent Link Lights
Lightin
g
Code Description Weight21 605 Link Light 5kg25 001 Aluminium Mast 6kg25 002 Basket 6kg06 015 Radiodetection CAT Scanner 2kg
c/w generator12 150 ‘Till Dawn’ Lamp 3kg
Consumables21 606 Festoon Light Bulb26 043 300w Halogen Lamp
624
Used to light up relatively large areas with veryfew lights. The light bracket is adjustable inheight from 1.5m to 2.4m.
Specification
Item code: 06-030
Height: 1.5m to 2.4m
Specification
Tripod Lights
625
We offer a range of rail skates and trolleysdesigned to be used as manual propelled,stand-alone load-bearing rolling platformsfor use on-track. See table below.
Specification
Specification
Rail Skates and TrolleysItem code: Various
Lifting and Sh
ifting
Code Description Weight (kg)
09 009 4 way Sleeper Beam 51.0(c/w chains)
09 010 8 way Sleeper Beam 95.0(c/w chains)
09 011 7 metre Rail Lifting Beam 1520.0
09 012 Rail Trolley (Type B) 130.0(c/w handles)
09 013 Link Trolley (Type A) 50.0(c/w handles)
09 016 3.5 metre Rail Lifting Beam 760.0(c/w camlocks)
09 017 Robel Rail Lifter 17.0
09 018 Pull Lift 15.0
09 032 Rail Skates 26.8
09 037 Rail Trolley (Type B) Insulated 138.0
09 061 Link Trolley (Type A) Insulated 57.0
626
Item code: 09-015
Weight: 235kg (cw 400kg trolley)
EG04 Motorised Bogie
Specification
Specification
Frame: Welded tubular construction
Gauge: Standard (1435mm) conforms to BR W6 gauge
Dimensions: L: 1750mm. W: 1600mm
Seating: 4 (driver + 3 passengers)
Controls: Centrally positioned between seats
Brakes: Handbrake and Footbrake
Note: Brakes incorporate modifications to meet the latest engineering standards
Engine: Honda GX120, 4hp, 4-stroke petrol
Transmission: Auto variable speed
Drive: Front wheel drive
Speed: 0-32kph
Wheels: 240mm diameter aluminium
Weight: 138kg/141kg (dependent on specification)
Electrics: built-in lighting coils 12v/50W
Headlamp: 21W with switch
Rear Light: 5W red, with switch
Inspection Lights: 21W spotlight or optional twin 500W floodlights with generator
Warning Device: Horn with push-button
627
This obstructionless hydraulic jack is designedfor the aligning and slewing of track, points andcrossings. It has a 152mm lifting stroke and asafe working load of 8t.
Track Aligner
Lifting and Sh
ifting
Specification
Item code: 09 035
SWL: 8t
Lifting Stroke: 152mm
Weight (c/w handle): 24.2kg
Specification
628
Designed for use on crossings and switch pointson rails over 42kg/m.
The jack is obstructionless.
Hydraulic Toe Jack Types B and C
Specification
Item code: 10-034
Safe working load: 8t head / 5t toe
Closed height (mm): 235 head/95 toe
Toe to head: 140mm
Lifting stroke: 90mm
Weight: 18.5kg
Specification Type B
Specification
Item code: 10-041
Safe working load: 20t head / 15t toe
Closed height (mm): 343 head/191 toe
Toe to head: 152mm
Lifting stroke: 110mm
Weight: 36kg
Specification Type c
629
Designed for slewing, aligning and lifting track,this jack is obstructionless and will slew up to50mm.
Slewing Jack
Specification
Item code: 09 003
Lifting Capacity: 5t (shoe) 7t (head)
Lifting Stroke shoe: 160mm
Lifting Stroke head: 115mm
Lift per pump stroke: 4mm on shoe
Weight: 24.5kg
Weight of shoe: 3.5kg
Specification
Lifting and Sh
ifting
630
This obstructionless jack is fitted with anoverload safety valve and tested to 25% overthe rated capacity. The jack is placed under therail without removal of ballast. Despite its lowheight of 95mm the jack is capable of a 101mmlift due to its hydraulic telescopic ram.
Mini Track Jack (Pan Jack)
Specification
Item code: 09 002
SWL: 10t on head
Closed height: 95mm
Extended height: 196mm
Lifting stroke: 101mm
Weight of standard lever: 3.2kg
Weight of insulated lever: 2.5kg
Weight: 16.5kg
Specification
631
This jack operates by means of a suspendedpawl and therefore does not require a separatetripping mechanism. Capable of a 330mm lift.
Duff Jack
Specification
Item code: 09 001
Capacity head/toe: 15t / 7.5t
Lifting stroke: 330mm
Weight (steel handle): 31kg
Weight (aluminium handle): 24kg
Specification
Lifting and Sh
ifting
632
The Pandrol Mk4 is a self-propelled Fastclipinstallation/extraction machine. The MK4 iscontrolled by a single pedestrian operator via ahandheld control unit. The main advantages are
lWill lift concrete and steel sleepers
l Installs and extracts four clips simultaneously per sleeper at a rate of 900 sleepers per hour
lWork head frame lifts fully clear of railhead
l Hydrostatic braking
l Power for all operations is petrol hydraulic actuation
l Low sleeper lift (75mm max)
Pandrol MK4 Rail MountedApplicator (Fastclip Only)
Specification
Output (max): 900 sleepers/hr
Power: 25hp /18.4kw
Width/Height: 2300mm/1133mm
Length: 1871mm
Max speed on track: 3/4 mph
Specification Pandrol Mk4
Code Description Weight Vibration
11-001 Hydraulic Spike 14kg 2.5M/s2 Remover* (hand held)
11-004 AC-1 Rail Mounted 123kg Spike Remover
11-005 Hydraulic Pandrol 71kg 15.0M/s2clip Remover
11-019 Pandrol MK4 Applicator 1880kg 4.5M/s2 Extractor (Fastclip)
*Requires Hydraulic Power Pack 04-004 to operate
633
The Pandrol PCM-2P combines rapidperformance with simplicity of use andrequires only one operator. The main featuresof the machine are:
l The unit is immediately ready to use requiring no assembly
l Simultaneous insertion or extraction of two clips bytwo independent clamps
l Does not interfere with rail circuits due to the threeinsulated wheels
l Self-braking system intervenes automatically whenoperator releases the handle of the mechanism
Cembre PCM-2P ClippingMachine (Fastclip or Eclip)
Specification
Output (max): 720 clips/hr
Width/Height: 830mm/875mm
Length: 1470mm
Weight: 129kg
Specification Cembre PCM-2P (Fastclip)
Code Description Weight Vibration
20-052 Cembre PCM-2P 129kg <2.5M/s2Clipping Machine (Fastclip)
20-051 Cembre PCM-2P Clipping 111kg <2.5M/s2Machine (E-clip)
11-021 Robel 34.01 Clipping 182kg 1.9M/s2 Machine
Consumables21-003 Petrol 1.0kg per litre
Clip Applica
tors &
Extra
ctors
634
The Geismar AP11 is a petrol-driven machinedesigned for the insertion and extraction ofPandrol Fastclips. The machine is fitted with a T6head and performs simultaneous extraction orinsertion of two fastclips on both sides of therail. The main advantages of the system are:
l High Output l Tools can be exchanged within a few minutes
lWork on wooden or concrete sleeper configuration
l All operating controls located on same side of frame, in easy reach of the operator
l Pressure is continuously applied, whatever the operation and without any operator’s action
l Electrical switched return mechanism, increasing output whilst reducing operator fatigue
Geismar AP11 Rail MountedApplicator/Extractor (Fastclip)
Specification
Item code: 11-013
Engine: Honda-type GX160
Output (max): 1210 clips/hr
Thrust (max): 29kN
Dimensions (mm): 2100 x 835 x 935
Weight: 133kg
Vibration: 4.0/4.7M/s2
Consumables21-003 Petrol 1.0kg per litre
Specification
635
The Robel 34.01 is a petrol-driven machinedesigned for the insertion and extraction of allcommonly used clip fastenings that aremounted and dismounted in a 90 degree angletowards the rail (e.g. Fastclip). The machine hasa unique sleeper lifting mechanism for easyinsertion and extraction of clips. The mainadvantages of the Robel 34.01 are:
l Quick and easy switching between mounting and dismounting without switching the tools
l Powerful and precise hydraulic compact system
l Ergonomically designed and height-adjustable handle bars
lWell positioned centre of gravity and low weight
Robel 34.01 Clipping Machine
Specification
Item code: 11-021
Engine: Honda-type GX200
Power output (max): 4.9kw at 3800rpm
Dimensions (mm): 2100 x 835 x 935
Weight: 182kg
Vibration: 1.9M/s2
Consumables21-003 Petrol 1.0kg per litre
Specification
Clip Applica
tors &
Extra
ctors
The Peltor DECT-Com II is a wireless intercomsystem, operating on the 1.8GHz DECT-frequencies.
The products in the Peltor DECT-Com II familyoffer simple and efficient wireless duplexcommunication with up to 9 active users talkingin full conference and additionally up to 40listeners with possibility to quick “break in” tothe conference.
There are basically two versions of theDECT-Com II main unit; base/portable units andportable units. A base/portable unit can beeither used as base or portable alternatively.
Due to low power output and high frequency itis a short range communication system. Thenominal working range is approximately 250metres outdoors in line of sight. The workingrange may be shorted due to actual conditions.
Peltor DECT-Com II WirelessIntercom System
636
Key Features
l Full duplex communication system
lWorking range typ. 250m outdoors / typ. 50mindoors (line of sight)
l Ghost voice guided menu system
l Up to three simultaneous talk groups
l Volume boost
l Noise gate (voice operated)
l All-call, between the channels (and synchronised systems)
lWireless PTT button for external radio etc. available
l Extended battery pack for longer usage time
Wire
less Co
mmunica
tions
637
Equipment and AccessoriesCode DescriptionX12-600 Dect Com II Std RadioX12-601 Dect Com II Base RadioX12-602 Dect Com II Base Radio cw Ext. InputX12-603 Dect Com II Charger For Std RadioX12-604 Dect Com II Charger For Base RadioX12-605 Dect Com II 12v Power Cable For Base RadioX12-606 Dect Com II Connector Cable to GP340 RadioX12-607 Dect Com II Lightweight Single Sided HeadsetX12-608 Dect Com II Std Headset cw NeckbandX12-609 Dect Com II XP Active Headset cw HeadbandX12-610 Dect Com II External Battery CarrierX12-611 Dect Com II Kit Carry Bag
ConsumablesCode Description12-613 Dect Com II Hygiene Kits For Std/Active Headsets12-612 Dect Com II Clean Pads For Std/Active Headsets12-614 Dect Com II 5m Roll Microphone Protector Tape
638
The Geismar MC3 grinds frogs, switch points,and stock rails. The pivoting grinding assemblypermits alignment of the grindstone parallel tostock rail for full grindstone to rail contact. Aflexshaft can be connected for use of hand toolsfrom the MC-3’s power supply. Optional set-offwheel is available.
Geismar MC3 grinder
Specification
Item code: 16-009
Weight: 102kg
Specification
639
The Geismar MP12 is Specifically designed forre-profiling of railheads after thermite welding.In the upright position, the machine can grindthe top surface of the rail, and in the inclinedposition grind the thickness of the head torecondition the railhead. A power take-off isprovided for fitting a flexible shaft for the useof other grinding tools.
Geismar MP12 grinder
Equipment and AccessoriesCode Description Weight Vibration16-001 Rail Profile Grinder (petrol) 72kg 13.8M/s216-002 Rail Profile Grinder (electric) 72kg 5.5M/s216-003 Rail Profile Grinder (hydraulic) 80kg16-032 Weld Trimmers 67kg16-005 Matweld Double Weld Shears (man) 67kg16-007 Geismar MS9 Grinder 100kg 6.0M/s216-008 Robel Switchblade/Frog Grinder 100kg 1.3M/s216-011 Handheld 5in Mini Grinder (110v) 3kg 2.5M/s216-012 Hand held 7in Angle Grinder (110v) 6kg 2.5M/s216-013 Hand held 9in Angle Grinder (110v) 6kg 2.5M/s216-014 Hand held 12in Angle Grinder (110v) 12kg 2.5M/s216-015 12 in 2-Stroke Disc Cutter (petrol) 10.5kg 8.9M/s216-026 Geismar MLC Grinder (Petrol) 1.3M/s216-029 ‘A-Frame’ Grinder Frame16-031 Geismar ESN3 Double Weld Shears 70kg
ConsumablesCode Description Weight 21-444 Grinding Stone Stumec MP12 (profile grinder) 2kg
Cuttin
g and Grin
ding Eq
uipment
640
Robokatta is a new concept in Rail Disc Saws bycombining a powerful and robust saw with theworlds first automatic support arm which,during the cutting phase, allows the operator tobe in control but away from the machine andtherefore subject to:l Vibration: Zero l Sparks: Zerol Physical Effort: Zero l Exhaust Fumes: Zerol Harmful Dust: Zero l Acoustic Noise: Minimum
Robokatta AutomaticRail Disc Saw
Specification
Item code: 01-052
Power Source: 2-stroke petrol
Power: 5.8kW (7.9hp)
Dimensions L/W/H: 798/285/440mm
(without disc)
Weight: 19kgAutomatic Support Arm Weight: 19.8kg
Equipment and AccessoriesCode Description Weight01-052 Robokatta Automatic Rail Disc Saw 19.0kg01-053 Cembre Automatic Rail Saw Cutting Arm01-054 Cembre Rail Saw Auxiliary Switching Device01-055 Cembre Rail Saw Transport Box01-056 Cembre Rail Saw Cutting Arm Transport Box
Consumables21-039 Two Stroke Premix Fuel (Petrol and Oil)21-454 16″ Rail Cutting Disc
Specification
641
The powerhead is fitted with an electronicgovernor in the ignition system ensuring thatthe blade does not over-speed or exceed itsperipheral speed even as the machine runs outof fuel.
Husqvarna Rail Cutters
Specification
Item code: 01-002
Power Source: 2-stroke petrol
Engine Capacity: 119cc
Power: 5.8kW (7.8hp)
Arbor Size: 25.4mm
Total Weight: 30.0kg
Equipment and AccessoriesCode Description Weight Vibration01-002 14” Rail Cutter (K1260) 30.0kg 5.0/6.0M/s201-005 14” Cut Off Saw 10.4kg 6.0/8.0M/s201-007 14” Rail Cutter (c/w isolation switch) 29.0kg 5.0/6.0M/s216-122 16” Rail Cutter (K1260) 15.0kg 3.6/4.1M/s2
Consumables Weight
21-001 2-Stroke Oil 1.0kg per litre21-003 Petrol 1.0kg per litre21-437 12in cutting disc for metal 0.5kg21-438 12in cutting disc for stone 0.5kg21-439 14in cutting disc for rail 0.85kg
Specification
Rail D
isk Cu
tters
642
The Cembre system allows the bush to beinstalled in all weather and environmentalconditions with a simple, easy to operate tool,producing a consistent, quality installation,independent from the skill of the operator. Thereduced installation time of this system willresult in overall cost savings.
The HTEPE-DET hydraulic hand tool comprises of:
a: Hydraulic pump tool body
b: Hydraulic installation head
c: Plastic carrying case
d: Two plungers
e: Go-No-Go gauge
Cembre HTEPE-DET Installation Tool
Specification
Item codes: 16-030 (12mm)
55-074 (16mm)
Pump body length: 275mm
Pump body width: 130mm
Head length: 106mm
Weight: 3kg
Specification
643
The Cembre SD-9P2 is extremely compact,practical and purposely designed for the drillingof wooden sleepers in complete safety.Weighing only 19kg, it is lightweight, easy tocarry around and needs no separate supportingstand. During operation, transmission ofvibrations are considerably reduced by anintegral shock absorber between the driveshaft and spindle.
Hand Held Sleeper Drilling Machine SD-9P2
Specification
Item code: 03-007
Engine: 48.6cc 2-stroke
Bit Diameter: 19mm (max)
Drilling Thickness: 200mm max
Power: 1.9hp/1.4kW
Total Weight: 19kg
Vibration: 2.5M/s
Equipment and AccessoriesCode Description Weight16-030 Cembre HTEPE-DET Rail Web Tool 3.0kg
Specification
Rail D
rilling
644
Both the petrol driven LD-1P and electric drivenLD-2E rail drills from Cembre have beenspecifically designed for use in railwayapplications providing consistently accuratework whatever the weather conditions.Compact in size, these drills afford considerabletime savings by allowing direct operation incases which previously have entailed armamentremoval. Special twist drills can be used for holediameters from 7 to 22mm on rails up to 45mmin thickness and broach cutters for 13 to 32mmhole diameters on rails up to 50mm thick.
Each model is provided with a coolant systemconsisting of a reservoir and pump which isconnected via a quick release couplerarrangement. Both units are lightweight andideally suited for one-man operation.
Cembre LD-1P & LD-2E 110
Specification
Item code: 03-006
Engine: 110v 50hz single phase
Drilling Range: 7 to 32mm
Drilling Thickness: 50mm (max)
Power: 1.8kW
Total Weight: 18kg
Specification LD-2E 110 Rail Drill
645
Cembre LD-1P & LD-2E 110
Specification
Item code: 03-005
Engine: 33cc 2-stroke
Drilling Range: 7 to 32mm
Drilling Thickness: 50mm (max)
Power: 0.88kW
Total Weight: 20kg
Specification LD-1P Rail Drill
Equipment and Accessories
Code Description Weight Vibration
03-005 Cembre LD-1P Rail Drill 20.0kg 2.5M/s2
03-006 Cembre LD-2E Rail Drill 18.0kg 2.5M/s2
03-007 Cembre SD-9 Sleeper Drill 20.0kg 2.5M/s2
16-030 Rail Bush Installation Tool
Rail D
rilling
646
This unique drill has a powerful 4hp four strokeengine which can drill two 3/8” or 9/32” holesin under 30 seconds. The drill offers automatichole positioning (57mm from base) on FB andRHB rails.
Abtus Twin Bond Hole Drill
Specification
Item code: 03-012
Weight: 42kg
Specification
647
Used to power anything from a single tripodlight up to 600m of trackside lighting. This noisecompliant diesel generator will run on ¾ loadfor up to 10 hrs before needing to be refuelled,ideal for lighting or powering up a site cabin.The generator can run a maximum of 63no72watt link lights. In practice it is best to reducethis down to 50-55no to reduce the load on thegenerator and increase fuel efficiency.
We also offers a complete range of petrol anddiesel generators, please see the table below:
Specification
Specification
5.0 Kva Generator
Diesel and Petro
l Generators
Code Description Weight (kg)
05-001 1.5kVA 110v ‘Silent’ Diesel 30kg
05-002 2.0kVA 110v ‘Silent’ Diesel 41kg
05-003 2.0kVA 110v ‘Super Silent’ Diesel 60kg
05-004 3.0kVA 110v Petrol 58kg (c/w long run fuel tank)
05-005 3.0kVA 110v ‘Super Silent’ Diesel 65kg
05-006 5.0kVA 110v ‘Silent’ Diesel 112kg
05-007 6.5kVA 110v ‘Super Silent’ Diesel 230kg
05-008 10.0kVA 110v ‘Silent’ Diesel 372kg
05-009 8.0kVA Dual Voltage Diesel Diesel 198kg
05-010 3.0kVA 110v ‘Silent’ Diesel 54kg
05-013 7.0kVA 110v ‘Super Silent’ Diesel 230kg
05-016 5.0kVA 110v Petrol 64kg
648
Used to power anything from a single tripodlight up to 320m of trackside lighting. ThisRailtrack approved generator will run on ¾ loadfor up to 10 hrs before needing to be refuelled,ideal for lighting. The generator can run amaximum of 38no 72watt link lights. In practiceit is best to reduce this down to 32no to reducethe load on the generator and increase fuelefficiency.
We also offers a complete range of petrol anddiesel generators, please see the table onpage 45.
3.0kva 110v Generator
Specification
Item code: 05-004
Dimensions: 610 x 410 x 475mm
Tank Capacity: 11L
Noise Level: 72dBa 110v
Outlets: 1 x 16A; 1 x 32A
Weight: 40kg
Specification
649
Hand and Ballast ToolsHand and Ballast To
ols
Code Description Weight07 009 4ft Rail Gauge 16.0kg07 010 Sleeper Gauge (adjustable) 2.0kg07 023 Concrete Mini Mixer (Petrol) 61.0kg07 033 Sleeper Tongs (Concrete) 6.0kg07 040 Rail Grab 6.0kg07 042 Sledge Hammer 7.0kg07 045 Timber Nips 4.5kg07 046 Sleeper Tongs (Wood) 6.0kg07 047 Heel Bar 7.0kg07 048 Ballast Shovel 2.5kg07 049 SHC Bar 9.5kg07 050 Ballast Fork 2.5kg07 051 Fishplate Spanner (Large) 5.0kg07 052 Pick Axe 4.0kg07 055 Pan Puller (E Clip) 5.5kg07 056 Pan Setter (E Clip) 5.5kg07 061 T-Lifter 5.0kg07 062 Rail Turning Bar - Flat Bottom 5.0kg07 064 Pad Scraper - Heavy Duty 1.5kg07 067 Pandrol Installer (Fastclip) 7.2kg07 068 Pandrol Lifter (Fastclip) 6.5kg07 069 Pandrol Extractor (Fastclip) 7.2kg07 072 Fishplate Spanner (Small) 5.0kg07 087 Keying Hammer (Insulated) 5.5kg07 089 Ballast Fork (Insulated) 2.5kg07 090 Ballast Shovel (Insulated) 2.5kg07 091 Pick Axe (Insulated) 4.0kg07 093 Heel Bar (Insulated) 7.0kg07 124 Concrete Mini Mixer (110v) 57.0kg15 012 Emergency Clamp 5.0kg25 305 Pot Dolly (Insulated) 5.0kg
All tools can be supplied fully insulated, suitable forthird-rail applications where appropriate.
650
l Demolition of concrete and masonry, workingat floor level or below waist level
l Corrective chiselling such as adjustments to door and window openings
l Penetrations for pipes, air ducts and cables
l Renovation of floors of all kinds
l Special applications such as floor tile removal,bushing and compacting
l Can be supplied with Electronic Warning System
Hilti TE1000 AVR Breaker
Specification
Item code: 22-213 Tamping Tool 22-290
Power Input: 1.6kW
Hammer Speed under load:1950 blows/min
Single Impact Energy: 22J
Vibration: 6.5m/sec2
Dimensions: 700x138x230mm
Breaker Weight: 11.8kg
Total Weight: 12kg
Specification
651
Hand held stoneblowing (HHSB) is basically anautomated form of the old fashioned buteffective method of measured shovel packing,i.e. the method of restoring longitudinal trackgeometry. The equipment utilises a lightweightcompressor and results in a system that is bothportable and more advanced than previousHHSB methods. The system is particularly suitedto S & C maintenance, especially around switchtoes and crossing areas.
Stoneblower c/wPowerpack & Compressor
Specification
Item code: 10-007
Vibration: 16.4M/s2
Weight: 137.0kg
ConsumablesCode Description Weight21-004 Diesel 1.0kg per litre21-003 Petrol 1.0kg per litre
Specification
Ballast a
nd Ta
mping
652
The Cobra TT has been specially developed fortamping. An impact of 40 joules combined withhammer speed of 1620 blows/minute meansimproved efficiency and drastically reducedballast pulverisation. Weighing only 25kg theCobra TT is easy to move around and comesequipped with a new dampening system thatvirtually eliminates vibration. The 90cc two-stroke petrol driven engine meets the toughestemission limit regulations.
Can be supplied with Electronic WarningSystems (see items 12-006 & 12-009).
Atlas Copco Cobra TTTamper
Specification
Item code: 10-030
Length/Depth: 927mm/331mm
Width/Width (handles folded): 611/390mm
Power Source: Two-stroke petrol Engine
Capacity: 90cc
Power Input: 1.2kW
Vibration: 2.3M/s2
Cooling System: Fan cooled
Impact Energy: 40J at 1620 blows/min
Hammer Speed: 720 – 1620 blows/min
Total Weight: 25kg
Specification
653
This machine is fully remote control thusremoving the operator’s need to touch the unitduring operation. The machine is designed tocompact large areas of ballast. Each unit can bebolted together to form a triple set which canbe operated by one person in either forward orreverse. A separate lifting beam is also suppliedfor ease of transport off and on track. Thebeam is subject to a 6 monthly load test orrecord of thorough examination.
Triple Vibrating Plate (Remote Control Type)
Specification
Remote Triple Wacker Plate (c\w lifting beam)
Item code: 10-046
Vibration: 16.4M/s2
Weight: 472.0kg
Specification
Specification
Small Wacker Plate
Item code: 10-006
Vibration: 17.0M/s2
Weight: 35.0kg
Specification
Ballast a
nd Ta
mping
652
The Robel 62.05 Vertical Tamper is extremelyuser friendly and is the lightest vibration tamperon the market with very low hand-armvibration. It has a high degree of consolidationfor excellent, high quality results.
The vertical tamper has a high tamping output ,less than two minutes per sleeper. Two devicescan be coupled via a connecting pipe forasynchronous tamping.
Robel 62.05 VerticalTamper
653
Ballast a
nd Ta
mping
Specification
Item code: 10-067
Height: 1190mm
Width: 495mm
Power Source: Two-stroke petrol Engine
Power Input: 1.4kW
Total Weight: 25kg
Specification
654
Torrent Trackside’s Rigid Safety Barrier Systemsoffer immediate, physical protection fortrackside workers without any specialist skills.By means of a simple clamping arrangement tothe foot of the running rail, the system can bequickly and easily erected without requiringballast penetration or any disturbance tosub-ballast services.
Rigid Safety BarrierSystems
SpecificationEquipment and Accessories
Code Description12-058 Vortok Safety Barrier System 3m pole12-059 Vortok Safety Barrier System Uprights12-061 Vortok Stillage12-064 Vortok Safety Barrier Arms12-066 Vortok Safety Barrier Gate12-800 Vortok Fencing (per metre)
655
Our range of warning and safety equipmentgives you the ability to block a section of trackor put in place a temporary speed restriction,quickly and efficiently. Each piece is designed sothat it can be placed on-site in its transportationmode and erected within minutes when therestriction is required.
AWD – Audible Warning DevicePowered by a small generator, the AWDconnects up to 2no 110v electric tampers likethe Hilti TE905AVR or the Kango 990K. Theoperator is then able to warn the machine userswhen they need to move to a position of safetyby releasing the button on the AWD, wherebysounding a warning siren and automaticallycutting the power to the tampers.
General Warning & safety Equipment
Code Description Weight (kg)
12-001 Audible Warning Device (AWD) 13.0kg
12-002 Marker Board 9.5kg
12-077 EROS LED Warning Board 23.0kg
Speed Board (many) 2.0kg
12-005 Yellow Track Magnet 40.0kg(c/w Transport Tube)
12-006* Gifas Warning System 10.0kg
12-012 Possession Limit Board (c/w base) 15.5kg
* For use with Atlas Copco TT Ballast Tampers
Safety and Warning Eq
uipment
656
The portable BB3 is suitable for all types ofinstallation and maintenance programmes.
The pin brazing process of the unit iselectronically controlled to provide totalconsistency and is pre-programmed to threesettings. The relevant setting is shown on eachpack of brazing pins. When the correct setting isselected on the control panel, the process isautomatically timed to provide an optimumbrazed connection. If required, it is also possibleto use brazing pins with a fuse wire.
The high power batteries can easily berecharged from a mains supply. The batterycapacity is sufficient for approximately 150brazes using the smallest type of brazing pin.
Pin Brazing Unit BB3
Code Description Weight (kg)
15-001 Genset MPM 5/225 IEBH Welder/Generator 121kg
15-006 Welding Oven 23kg
15-010 Hilti TE104 110v Needle Gun (vibration 9M/s2) 12kg
35-001 BB3 Pin Brazing Unit 47kg
Specification
Dimensions: 430 x 430 x 600mm
Batteries: 12v 26AH
Output current (max): 260A
Weight: 47kg
Specification BB3 Pin Brazing Unit
657
About Cold ExpansionRailway track is continually subjected to high cyclictensile loads generated by the passage of rollingstock over joints. Flexing and displacement of rails atbolted joints, combine to induce high tensile loads atthe bolt hole which often generates fatigue cracks. Ifleft undetected, these fatigue induced cracks can leadto fractures which in extreme cases could cause trainderailment. The cracking of rail-end bolt holes hasbeen a major concern for years and a cause ofpremature rail replacement, imposition of speedrestrictions and is a significant factor in rail inspectionand maintenance costs. Increased rolling stock loadsand heavier rail traffic has made it even moreessential to eliminate fatigue cracks and preventpotential costly derailments. Fatigue Technology’s(FTI) RailTec System substantially increases the life ofbolted rail by shielding bolt holes from the stressesthat cause cracks and failure. FTI’s system hassuccessfully extended the life of bolt holes in metalstructures for over 25 years.
l Improves the fatigue life of a hole by at least 300%
l Arrests the growth of small cracks
l Cost-effective alternative to replacement track
l Reduces maintenance and inspection costs
l Increases overall structural integrity and safety of the line
We are able to offer a specially adapted rail drillwhich has vertical and horizontal axes adjustmentsand comes complete with a range of tools foropening out bolt holes. The drill can be used for thefollowing applications:
Drilling 30mm holes in new track
Expanding undersize holes to 30mm
Expanding bolt holes in existing track prior to coldexpansion with three size options: 31mm; 32mm;33mm.
The drill and tooling eliminates the use of a Benklerrail drill, tapered bridge reamers and trolley mountedswivel jib. We also offer training on how to use ColdExpansion Equipment.
Cold Bolt Expansionand Huck Bolt
Cold Bolt Ex
pansio
n and Huck Bolt
658
Electric Powerpacks require a minimum of 5kVA.Hydraulic installation tools are supplied with onehose assembly
Cold Bolt Expansion EquipmentCode Description Weight (kg)
03-005 Plug Cutter Drill (Rail Drill) 20.0kg
18-001 Cold Expansion Puller Gun (FTI) 10.0kg
18-004 Cold Expansion Hydraulic Power Pack (FTI) 30.0kg
18-007 Cold Expansion Electric Power Pack (FTI) 30.0kg
14-001 Huck Bolt 1in Gun 23.0kg
14-002 Huck Bolt 1.25in Gun 23.0kg
14-003 Huck Bolt Powerpack (c/w hose set) 48.0kg
14-004 Huck Bolt Cutter 48.0kg
Cold Bolt Expansion ConsumablesCode Description Weight (kg)
22-014 Plug cutter 28-30 0.25kg
22-015 Plug cutter 29-31 0.25kg
22-016 Plug cutter 30-32 0.25kg
22-017 Plug cutter 31-33 0.25kg
18-026 31.0mm Sleeve 0.5kg per 10
18-027 32.0mm Sleeve 0.5kg per 10
18-028 33.0mm Sleeve 0.5kg per 10
18-029 30.0mm Sleeve 0.5kg per 10
659
HIREpod
Planning the right equipment for an OLE or
track maintenance project is a time
consuming and complicated business.
Over order and budget is wasted, under
order and the project can be delayed.
Our portable plant hire experts will plan the
correct equipment and consumables to
complete your project and deliver them to
site in our secure HIREpod.
Everything you need is delivered to site
and stored in one place. The HIREpod has
it’s own power source for sensor
activated lighting and dedicated charging
points for battery powered equipment.
To find out how your organisation can save
time and money get in touch with our
experts today.
HIREpodNEW
A revolutionary planningand onsite storage systemfor track & OLE projects
660
Delivered and stored inthe secure HIREpod
All equipment andconsumables in one place
Built in power source forequipment & recharging
We plan the rightequipment for the job
The HIREpod can be extended with a
bespoke Wellfare Unit which can add the
following services:
l Power
l Water
l Diesel
l Communications
l CCTV
l Security
661
Torrent Trackside provides high quality
services to the railway maintenance and
renewal contractors in the UK. Torrent help
their customers achieve the optimum levels
of safety by providing plant, equipment and
associated services to the highest of
standards. As well as rail and OHL specific
portable plant, Torrent also provide trackside
lighting, traffic management, and training to
their customer base. Staying on track 24
hours a day, 365 days a year, the business
supports both the Network Rail and London
Underground infrastructure.
As part of Vp plc, you can rely on outstanding
support from an established organisation with
over 50 years experience and expertise in the
specialist rental equipment field. Vp plc rent
and sell specialist produces and services across
a variety of industrial market sectors.
Vp plc, listed on the London Stock Exchange,
has a turnover in excess of £150million.
Vp plc consists of the following specialist
divisions.
662
UK Forks is the UK's leading specialist rental
provider of telescopic handlers, rough terrain
straight mast fork lift trucks and associated
products and services.
The business provides services to the
housebuilding, general construction and
industrial markets. UK Forks operates from a
network of locations across the country,
which act as distribution and maintenance
depots providing operational support.
TPA Portable Roadways is the UK market
leader for the provision of portable roadway
access solutions to the outdoor events,
transmission, construction and utility sectors.
TPA also operates in mainland Europe.
663
Airpac Bukom Oilfield Services is an
international business with 40 years'
experience in providing specialist equipment
and services to a range of oil and gas related
service markets. The primary market served
is exploration, where we provide a range of
high performance compressors, steam
generators, heat exchangers, sand filters and
highly skilled operators in support of well
testing projects.
Hire Station is dedicated to the supply of
tools, small equipment and allied services to a
wide range of end markets. Hire Station also
includes the specialist ESS Safeforce safety
equipment rental business and MEP Hire, a
provider of press fitting and fusion equipment
to the mechanical, electrical and plumbing
sector.
664
Groundforce is a UK market leading business
offering a portfolio of services to the
construction industry. Based around its core
activity, which is providing shoring and
trenching solutions to an extensive customer
base, the business operates primarily in the
UK, but also in mainland Europe. The shoring
business, Groundforce Shorco, provides a
range of equipment including trench boxes
and sheets and hydraulic bracing systems of
varying capacities.
665
For in-depth information about all
aspects of Torrent Trackside and to
order equipment and consumables
visit our new website at:
www.torrenttrackside.co.uk
The new website is continually
updated with out latest track and
OHL products aswell as latest news
and features about Torrent
Trackside, brochure downloads and
full details of our CSR policy.
Torrent Trackside Website
www.facebook.com/torrenttrackside
https://twitter.com/#!/VpTorrent
Follow us on social media
Torrent TracksideRailway Plant. Railway People.
24hr helpline0845 769 7168
Head Office:Network House
Europa Way
Britannia Enterprise Park
Lichfield
Staffordshire
WS14 9TZ