Poinsettia i e a4

5
Bouquet (poinsettia) : Assembly Instructions © Canon Inc. © Taka Taka Assembly Instructions Mountain fold(dotted line) Make a mountain fold. Valley fold(dashed and dotted line) Make a valley fold. Scissors line(solid line) Cut along the line. Cut in line(solid line) Cut along the line. Glue spot(Red dot) Glue parts with the same number together. Glue spot(Green dot) Glue within the same part. Glue spot(Blue dot) Glue to the rear of the other part. Glue The glue spot(colored dot) shows where to apply the glue. Tools and materials Assembly tip Caution Scissors, set square, glue(We recommend stick glue), pencil, used ballpoint pen, toothpicks, tweezers, (useful for handling small parts) Before gluing, crease the paper along mountain fold and valley fold lines and make sure rounded sections are nice and stiff. Glue, scissors and other tools may be dangerous to young children so be sure to keep them out of the reach of young children. View of completed model Assembly Instructions : Five A4 sheets (No. 1 to No. 5) *Hint: Trace along the folds with a ruler and an exhausted pen (no ink) to get a sharper, easier fold. * Build the model by carefully reading the Assembly Instructions , in the parts sheet page order. * This model was designed for Papercraft and may differ from the original in some respects. Before starting assembly : Writing the number of each section on its back side before cutting out the sections is highly recommended. (* This way, you can be sure which section is which even after cutting out the sections.) Indicates where sections should be glued together. Curve parts as indicated by these arrows. For durability, we recommend use of Canon Matte Photo Paper and woodworking adhesive. Indicates front/reverse of sections to be glued. Glue the same numbers to each other. These numbers indicate the order for applying glue. To curve the paper Use a pencil, screwdriver or other rod-like object. Basket assembly Crease the parts and apply glue. To simplify assembly, apply glue to parts in order, as indicated by the numbers. Make these parts rounded and apply glue. Make two ribbons.

Transcript of Poinsettia i e a4

Page 1: Poinsettia i e a4

Bouquet (poinsettia) : Assembly Instructions © Canon Inc. © Taka Taka

Assembly Instructions

Mountain fold(dotted line)Make a mountain fold.

Valley fold(dashed and dotted line)Make a valley fold.

Scissors line(solid line)Cut along the line.

Cut in line(solid line)Cut along the line.

Glue spot(Red dot)Glue parts with the same number together.

Glue spot(Green dot)Glue within the same part.

Glue spot(Blue dot)Glue to the rear of the other part.

GlueThe glue spot(colored dot)shows where to apply the glue.

Tools and materials

Assembly tip

Caution

Scissors, set square, glue(We recommend stick glue), pencil, usedballpoint pen, toothpicks, tweezers, (useful for handling small parts)

Before gluing, crease the paper along mountain fold and valley fold lines and make sure rounded sections are nice and stiff.

Glue, scissors and other tools may be dangerous to young children so be sure to keep them out of the reach of young children.

View of completed model

Assembly Instructions : Five A4 sheets (No. 1 to No. 5)

*Hint: Trace along the folds with a ruler and an exhausted pen (no ink) to get a sharper, easier fold.

* Build the model by carefully reading the Assembly Instructions , in the parts sheet page order.

* This model was designed for Papercraft and may differ from the original in some respects.

Before starting assembly : Writing the number of each section on its back side before cutting out the sections is highly recommended.(* This way, you can be sure which section is which even after cutting out the sections.)

Indicates where sections should be glued together.

Curve parts as indicated by these arrows.

For durability, we recommend use of Canon Matte Photo Paper and woodworking adhesive.

Indicates front/reverse of sections to be glued. Glue the same numbers to each other. These numbers indicate the order for applying glue.

To curve the paperUse a pencil, screwdriver or other rod-like object.

Basket assemblyCrease the parts and apply glue. To simplify assembly, apply glue to parts in order, as indicated by the numbers.

Make these parts rounded and apply glue.

Make two ribbons.

Page 2: Poinsettia i e a4

Poinsettia assemblyThe bouquet consists of six poinsettias, in three sizes and three colors. All poinsett ias are assembled in the same way. The example shows assembly of poinsettia A.

Assemble poinsettia A, then assemble the other poinsettias. To simplify assembly, apply glue to parts in order, as indicated by numbers.

Curve parts A2 to A13 (leaves) from the base to the tip of each leaf, and fold creases as indicated. Then apply glue.

Enlarged view of hexagonal flapCompleted basket

Completed flowerCompleted attachment ring

Reference number

Number

Color

Size

Total

© Taka Taka

CAUTION

Do not hit other people with the pointed edges.Doing so could result in injury.

Adults should make sure that children observe this caution.

Bouquet (poinsettia) : Assembly Instructions © Canon Inc. © Taka Taka

Page 3: Poinsettia i e a4

Assemble parts A1 to A13 by layering with the hexagonal flap at the center of the flower.

Layer underneath

Layer underneath

Layer underneath

Layer underneath

Completed poinsettia A

Layer underneath

Bouquet (poinsettia) : Assembly Instructions © Canon Inc. © Taka Taka

Page 4: Poinsettia i e a4

Poinsettia B assemblyAssemble poinsettia B, following stepsto from instruction for poinsettia A. Do not glue part B14 at this time.

Bouquet decorative ribbon assemblyThe three types of decorative ribbons (parts 2-1, 2-2, and 2-3) are different patterns and sizes, but the assembly process for each is the same.

Bouquet decorative leaf assemblyThere are three types of decorative leaves.

Poinsettias C, D, E, & F assemblyPoinsettias C, D, E and F do not have green leaves. Assemble the red leaves, following steps to from instruction for poinsettia A. Then follow steps and to attach parts that correspond to A1 and A14.

Curve parts 3-1 and 3-2 from the base to the tip of each leaf.

Part 3-3 should be assembled following steps and from instruction for poinsettia A.

Glue reverse sides together.Poinsettia B

Completed mini-bouquet

Glue mini-bouquet ribbons together at a pleasing angle.

Mini-bouquet assembly

Bouquet (poinsettia) : Assembly Instructions © Canon Inc. © Taka Taka

Page 5: Poinsettia i e a4

bouquet assembly

Glue the red dots on the attachment rings to the basket.

Completed poinsettia bouquet

Enjoy the Paper Craft mixed arrangements pictured below.

Bouquet (roses) Bouquet (tulips)

Glue the yellow dots on the ribbons and the backs of the leaves to the basket as if you were creating a flower arrangement.

Bouquet (poinsettia) : Assembly Instructions © Canon Inc. © Taka Taka