Plummer Block Tutorial

7/30/2019 Plummer Block Tutorial

1/21

Tutorial on Plummer Block

Hareesha N G

Assistant Professor

Dept of Aeronautical Engg

Dayananda Sagar College of Engg

Bangalore-78

4/9/2013 1Hareesha N Gowda, DSCE, Blore-78


2/21

2.Plummer Block



3/21

Part 1: Body:

1. Create the sketch as shown in figure

2. Use Protrusion command to create the 3D feature, width 36 mm


3. Use mirror copy feature (smart option), mirror other side of the body

Select feature Right click to acceptSelect mirror plane Finish


4/21

4/9/2013 Hareesha N Gowda, DSCE, Blore-78 4


5/21

Part 1: Body:1. Select top surface plane,

2. Create the sketch on top face of the body as shown in figure

3. Use cutout command to create the 3D feature shown in figure, show outside cutoutwhile creating cutout.

4. Use from/ to option, select top and bottom surface of the body



6/21

Part 1: Body:1. Select bottom plane, Create the sketch by selecting bottom face as shown in figure

3. Use cut out, depth 2 mm.



7/21

Part 1: Body:1. Select bottom plane,

2. Create the sketch by selecting bottom face as shown in figure

3. Use cut out command to create the 3D feature, depth through all.



8/21

Part 1: Body:


Use mirror copy feature (smart option), mirror all features to other side of the body

Select all features to be mirrored (Hold Ctrl Key and edge bar to select) Right click to accept

Select mirror plane Finish


9/21

Part 1: Body:

1. Select top surface2. Use hole command to create the 3D feature shown in figure using

parameters shown



10/21

Part 2: cup:

1. Select YZ plane,

2. Crete the sketch as shown in figure3. Use protrusion command to create

the 3D feature, width 36 mm



11/21

Part 2: cup:

1. Select top surfece2. Crete the sketch as shown in figure

3. Use cutout command to create the 3D

feature shown in figure, show outside

cutout while using the command



12/21

Part 2: cup:

1. Select top surface2. Crete the sketch as shown in figure

3. Use cutout command to create the 3D feature shown in figure



13/21

Part 2: cup:

1. Create a plane tangent to top surface2. Hole command to create the 3D feature

shown in figure using parameters defined



14/21

Part 3: Bottom half bearing

1. Select YZ plane,2. Crete the sketch as shown in figure

3. Use revolved protrusion command to create

the 3D feature shown in figure, use 180o



15/21

Part 3: Bottom half bearing1. Select YZ plane,

2. Crete the sketch as shown in figure

3. Use revolved protrusion command to create the 3Dfeature shown in figure, revolution 180o



16/21

Part 3: Bottom half bearing1. Select left surface


3. Use cutout command to create the 3D feature shown in figure



17/21

Part 4: Bearing top half1. Save the previous part (part.3- Bottom half) file as

Bearing top half

2. Delete unwanted, create hole as shown.



18/21

Part - 5: Bolt M10

1. Select top plane, create sketch as shown in fig.

2. Select xz plane, create sketch as shown, use revolved cut out to create bolt

chamfer as shown.



19/21

Part 6: Nut M10

1. Select top plane


3. Use symmetric protrusion command, height-8mm to create features asshown in figure. Create threaded hole as shown.


4. Select XZ plane, create sketch as shown in fig. use revolved cutout (outside cut) to create

features as shown in figure. Mirror to other side.


20/21

Part 7: Lock Nut M10

Save the previous file( M10 Nut) as lock Nut M10, change the

protrusion height to 5mm.



21/21

Part-6: Shaft

Select YZ plane, create sketch as shown in fig.

4/9/2013 Hareesha N Gowda, DSCE, Blore-78 21

Plummer Block Tutorial

Documents

Transcript of Plummer Block Tutorial