Plates and Screwsdownload.breakpoint.sk/_timed/27-34.pdf · · 2013-01-03Plates and Screws axSOS...

Plates and Screws

axSOS Locking Plate System

variax distal Radius Locking Plate System

*This does not replace the operative technique, please refer to the operative technique for all procedures. **Not drawn to scale. *This does not replace the operative technique, please refer to the operative technique for all procedures. **Not drawn to scale.

OSTEOSYNTHESIS | Plates and Screws | AxSOS Locking Plate System 5655 OSTEOSYNTHESIS | Plates and Screws | AxSOS Locking Plate System

axSOS Locking Plate System

Ordering Information – Implants

4.0MM cabLE PLuG

PROxIMaL LaTERaL TIbIa Locking Screws 4.0mm Standard Screws 3.5, 4.0mm

4.0MM LOcKING INSERT

Note: For Sterile Implants, add "S" to the REF.

Stainless Steel Plate Shaft Locking Locking REF Length Holes Holes Holes Left Right mm Metaphyseal Shaft

437302 437322 95 2 5 1 437304 437324 121 4 5 2 437306 437326 147 6 5 3 437308 437328 173 8 5 4 437310 437330 199 10 5 5 437312 437332 225 12 5 6 437314 437334 251 14 5 7

Stainless Steel System REF mm

370004 4.0

Stainless Steel System REF mm

4.0

Note: For Sterile Implants, add "S" to the REF.

4.0MM LOcKING ScREw, SELF TaPPINGT15 Drive

3.5MM cORTIcaL ScREw, SELF TaPPING2.5mm Hex Drive

4.0MM caNcELLOuS ScREw, PaRTIaL THREad2.5mm Hex Drive

4.0MM caNcELLOuS ScREw, FuLL THREad2.5mm Hex Drive

eel Screw REF Length mm

371514 14 371516 16 371518 18 371520 20 371522 22 371524 24 371526 26 371528 28 371530 30 371532 32 371534 34 371536 36 371538 38 371540 40 371542 42 371544 44 371546 46 371548 48 371550 50 371555 55 371560 60 371565 65 371570 70 371575 75 371580 80 371585 85 371590 90 371595 95

Stainless Steel Screw REF Length mm

338614 14 338616 16 338618 18 338620 20 338622 22 338624 24 338626 26 338628 28 338630 30 338632 32 338634 34 338636 36 338638 38 338640 40 338642 42 338644 44 338646 46 338648 48 338650 50 338655 55 338660 60 338665 65 338670 70 338675 75 338680 80 338685 85 338690 90 338695 95


345514 14 345516 16 345518 18 345520 20 345522 22 345524 24 345526 26 345528 28 345530 30 345532 32 345534 34 345536 36 345538 38 345540 40 345545 45 345550 50 345555 55 345560 60 345565 65 345570 70 345575 75 345580 80 345585 85 345590 90 345595 95


345414 14 345416 16 345418 18 345420 20 345422 22 345424 24 345426 26 345428 28 345430 30 345432 32 345434 34 345436 36 345438 38 345440 40 345445 45 345450 50 345455 55 345460 60 345465 65 345470 70 345475 75 345480 80 345485 85 345490 90 345495 95


57 OSTEOSYNTHESIS | Plates and Screws | AxSOS Locking Plate System OSTEOSYNTHESIS | Plates and Screws | AxSOS Locking Plate System 58

Ordering Information – Instruments

REF Description

4.0mm Locking Instruments

702742 Drill Ø3.1mm × 204mm

702772 Tap Ø4.0mm × 140mm

702747 Screwdriver T15, L200mm

702753 Solid Screwdriver Bit T15, L115mm

702732 Screw Holding Sleeve

702702 K-Wire Sleeve

702707 Drill Sleeve

702884 Direct Depth Gauge for Locking Screws

702750 Universal Torque Limiter T15 / 4.0mm

702762 Locking Insert Inserter 4.0mm

702427 T-Handle Small, AO Fitting

38111090 K-Wire (Trocar Point Steinmann Pin Ø2.0mm × 230mm)

702767 Locking Insert Extractor

702778 Handle for Plate Insertion

702712 Drill/K-Wire Measure Gauge

702776 Temporary Plate Holder

702776-1 Spare Shaft for Temporary Plate Holder

702919 Soft Tissue Spreader

702961 Trocar (for Soft Tissue Spreader)

702782 Soft Tissue Elevator

702756 Bending Irons (×2)

REF Description

4.0mm Locking Instruments

702968 Locking Insert Forceps

702671 Guide for Centering Pin

702673 Centering Pin

702675 Adapter for Centering Pin

702729 Proximal Tibia, Aiming Block, Left

702728 Proximal Tibia, Aiming Block, Right

702720-2 Spare Set Screw for Tibia Aiming Block

702793 Plate Trial/Shaft Hole Locator - Proximal Tibia

Optional Instruments

703616 Drill Ø3.1 × 204mm, flat Tip

OSTEOSYNTHESIS | xxxxxxx | xxxxxxx 60


59 OSTEOSYNTHESIS | Plates and Screws | VariAx Distal Radius Locking Plate System OSTEOSYNTHESIS | Plates and Screws | VariAx Distal Radius Locking Plate System 60

REF Description

SPS Standard Instruments

700347 Drill Bit Ø2.5mm × 125mm, AO



702805 Tap Ø4.0mm × 180mm, AO

702418 Drilling Guide Ø3.5/2.5mm

702822 Drill Sleeve Handle

702825 Drill Sleeve Ø2.5mm Neutral

702829 Drill Sleeve Ø2.5mm Compression

702831 Drill Sleeve Ø2.5mm Buttress

702709 Percutaneous Drill Sleeve Ø2.5mm

702957 Percutaneous Drill Sleeve Ø2.5mm Neutral

702879 Depth Gauge 0-150mm for Screws Ø3.5/4.0mm

702841 Screwdriver Hex 2.5mm for Standard Screws L200mm

702485 Solid Screwdriver Bit, Hex 2.5mm for Standard Screws L115mm

702490 Holding Sleeve for Screwdrivers For Screwheads: Ø6.0mm

702428 Tear Drop Handle, small, AO Fitting

900106 Screw Forceps

390164 K-Wires 1.6mm × 150mm (optional)

390192 K-Wires 2.0mm × 150mm

Other Instruments

702755 Torque Tester with Adapters

981081 X-Ray Template, Proximal Tibia

Cases and Trays

902955 Metal Base - Instruments

902929 Lid for Base - Instruments

902930 Instrument Tray 1 (Top)

902931 Instrument Tray 2 (Middle)

902963 Instrument Tray 3 (Bottom incl. Locking Insert Forceps)

902932 Screw Rack

902949 Metal Base - Screw Rack

902950 Metal Lid for Base - Screw Rack

902947 Metal Base - Implants

902971 Implant Tray - Proximal Lateral Tibia

902976 Lid for Implant Tray -Proximal Lateral Tibia

902958 Locking Insert Storage Box 4.0mm

variax distal Radius Locking Plate System

Note:Plate Trials for the determina-tion of size intra-operatively are available on page 16.

The Variax Distal Radius Plating System incorporates plate designs originating from the Matrix Distal Radius Plating System developed by Stryker in conjunction with Richard Rogachefsky, MD.

* They can be ordered single sterile-packed by placing a “S” at the end of the Cat. Nr.

aNaTOMIcaL vOLaR PLaTES* REF Description Length Thickness mm mm

54-25384 Anatomical Volar DR Plate Narrow, Right 56 2

54-25374 Anatomical Volar DR Plate Narrow, Left 56 2

54-25386 Anatomical Volar DR Plate Standard, Right 56 2

54-25376 Anatomical Volar DR Plate Standard, Left 56 2

54-25385 Anatomical Volar DR Plate Narrow, Right, Long 76 2

54-25375 Anatomical Volar DR Plate Narrow, Left, Long 76 2

54-25387 Anatomical Volar DR Plate Standard, Right, Long 76 2

54-25377 Anatomical Volar DR Plate Standard, Left, Long 76 2

uNIvERSaL vOLaR PLaTES* REF Description Length Thickness mm mm

54-25394 Universal Volar DR Plate Narrow, Short 53 2

54-25396 Universal Volar DR Plate Standard, Short 53 2

54-25398 Universal Volar DR Plate Wide, Short 53 2

54-25395 Universal Volar DR Plate Narrow, Long 73 2

54-25397 Universal Volar DR Plate Standard, Long 73 2

54-25399 Universal Volar DR Plate Wide, Long 73 2

54-25391 Universal Volar DR Plate Narrow, XLong 94 2

54-25392 Universal Volar DR Plate Standard, XLong 94 2

54-25393 Universal Volar DR Plate Wide, XLong 94 2

Ordering Information – Instruments


OSTEOSYNTHESIS | Plates and Screws | VariAx Distal Radius Locking Plate System 6261 OSTEOSYNTHESIS | Plates and Screws | AxSOS Locking Plate System

Ordering Information – Plates Ordering Information – Plates

xxL aNaTOMIcaL vOLaR PLaTES*

REF Description Length Thickness mm mm

54-25420 2.7mm XXL Volar DR Plate, Stand, LE (15 holes) 189 3 54-25422 2.7mm XXL Volar DR Plate, Stand, RI (15 holes) 189 3




54-25436 2.7mm XXL Volar DR Plate, Narrow, LE (15 holes) 189 3 54-25438 2.7mm XXL Volar DR Plate, Narrow, RI (15 holes) 189 3




Note:Plate Trials for the determination of size intra-operatively are avail-able on page 16.

The Variax Distal Radius Plating System incorporates plate designs originating from the Matrix Distal Radius Plating System developed by Stryker in conjunction with Richard Rogachefsky, MD.

* They can be ordered single sterile-packed by placing a “S” at the end of the Cat. Nr.

Note:Plate Trials for the determination of size intra-operatively are avail-able on page 16.

* They can be ordered single sterile-packed by placing a “S” at the end of the Cat. Nr.** Formerly labelled as “Radial Column Plate”*** Formerly labelled as “Ulnar Column Plate

FRaGMENT SPEcIFIc PLaTES*

dORSaL PLaTES*

REF Description Length Thickness mm mm

54-25290 Dorsal DR Plate Standard, Right 60 1.5

54-25291 Dorsal DR Plate Standard, Left 60 1.5

54-25292 Dorsal DR Plate Wide, Right 60 1.5

54-25293 Dorsal DR Plate Wide, Left 60 1.5

54-25294 Dorsal DR Plate Standard, Right, XLong 81 1.5

54-25295 Dorsal DR Plate Standard, Left, XLong 81 1.5

54-25296 Universal Volar DR Plate Wide, Right, XLong 81 1.5

54-25297 Dorsal DR Plate Wide, Left, Xlong 81 1.5

REF Description Length Thickness

mm mm

54-25400 Lateral DR Plate, Short** 44 1

54-25401 Lateral DR Plate, Long** 57 1

54-25402 Dorsal Medial DR Plate, Short, Right*** 40 1

54-25403 Dorsal Medial DR Plate, Short, Left*** 40 1

54-25404 Dorsal Medial DR Plate, Long, Right*** 53 1

54-25405 Dorsal Medial DR Plate, Long, Left*** 53 1



Ordering Information – Cross-Pin Screws Ordering Information – Cross-Pin Screws

Note: They can be ordered single sterile-packed by placing a “S” at the end of the Cat. Nr.All Drills may be ordered sterile by replacing “60” by “91-” in their respective Cat.Nr.

Note: They can be ordered single sterile-packed by placing a “S” at the end of the Cat. Nr.All Drills may be ordered sterile by replacing “60” by “91-” in their respective Cat.Nr.

2.7 MM PaRTIaLLY THREadEd LOcKING ScREwS

Ti Length REF mm

52-20616 16 52-20618 18 52-20620 20 52-20622 22 52-20624 24

52-20626 26

2.0MM LOcKING PEGS 2.7MM LOcKING ScREwS 2.3MM NON-LOcKING ScREwS 2.7MM PaRTIaLLY THREadEd NON-LOcKING ScREwS

Ti Length REF mm

52-23010 10 52-23012 12 52-23014 14 52-23016 16 52-23018 18 52-23020 20 52-23022 22 52-23024 24 52-23026 26 52-23028 28 52-23030 30 52-23032 32 52-23034 34 52-23036 36 52-23038 38

Ti Length REF mm

52-27610 10 52-27612 12 52-27614 14 52-27616 16 52-27618 18 52-27620 20 52-27622 22 52-27624 24 52-27626 26

Ti Length REF mm

52-27116 16 52-27118 18 52-27120 20 52-27122 22 52-27124 24

52-27126 26

Ti Length REF mm

52-27716 16 52-27718 18 52-27720 20 52-27722 22 52-27724 24

52-27726 26

For the 2.0mm Locking Pegs, please use the fol-lowing 2.0mm drill ref: 60-20185, 60-20385 and 60-20485.

2.3MM LOcKING ScREwS

Ti Length REF mm

52-23610 10 52-23612 12 52-23614 14 52-23616 16 52-23618 18 52-23620 20 52-23622 22 52-23624 24 52-23626 26 52-23628 28 52-23630 30 52-23632 32 52-23634 34 52-23636 36 52-23638 38

For the 2.3mm Locking Screws, please use the following 1.9mm drill ref: 60-19140, 60-19340 and 60-19440.

For the 2.3mm Screws, please use the following 1.9mm drill ref: 60-19140, 60-19340 and 60-19440.

For the 2.7mm Locking Screws, please use the fol-lowing 2.0mm drill ref: 60-20185, 60-20385 and 60-20485.

2.7MM NON-LOcKING ScREwS

Ti Length REF mm

52-27010 10 52-27012 12 52-27014 14 52-27016 16 52-27018 18 52-27020 20 52-27022 22 52-27024 24 52-27026 26


For the 2.7mm Partially Threaded Screws, please use the following 2.0mm drill ref: 60-20185, 60-20385 and 60-20485.

For the 2.7mm Partially Threaded Locking Screws, please use the following 2.0mm drill ref: 60-20185, 60-20385 and 60-20485.

REF Description

60-23141 2.3mm, Stryker shaft end 60-23341 2.3mm, AO shaft end 60-23441 2.3mm, Dental shaft end 60-20185 2.0mm, Stryker shaft end 60-20385 2.0mm, AO shaft end 60-20485 2.0mm, Dental shaft end 60-19140 1.9mm, Stryker shaft end 60-19340 1.9mm, AO shaft end 60-19440 1.9mm, Dental shaft end 62-27010 Tap for 2.7mm Screws 62-27007 2.3mm/2.7mm, Cross-Pin Blade

TwIST dRILLS, TaP aNd bLadE



Ordering Information – T7 Drive Screws Ordering Information – T7 Drive Screws

Note: They can be ordered single sterile-packed by replacing “E” by “S” at the end of the Cat. Nr.All Drills may be ordered sterile by replacing “60” by “91-” in their respective Cat.Nr.

Note: They can be ordered single sterile-packed by replacing “E” by “S” at the end of the Cat. Nr.All Drills may be ordered sterile by replacing “60” by “91-” in their respective Cat.Nr.

Ti Length REF mm

53-20616E 16 53-20618E 18 53-20620E 20 53-20622E 22 53-20624E 24

53-20626E 26

2.0MM LOcKING PEGS 2.7MM LOcKING ScREwS 2.3MM NON-LOcKING ScREwS 2.7MM PaRTIaLLY THREadEd NON-LOcKING ScREwS

REF Description

60-23141 2.3mm, Stryker shaft end 60-23341 2.3mm, AO shaft end 60-23441 2.3mm, Dental shaft end 60-20185 2.0mm, Stryker shaft end 60-20385 2.0mm, AO shaft end 60-20485 2.0mm, Dental shaft end 60-19140 1.9mm, Stryker shaft end 60-19340 1.9mm, AO shaft end 60-19440 1.9mm, Dental shaft end 62-27010 Tap for 2.7mm Screws 62-27015 Screwdriver Blade, T7

TwIST dRILLS, TaP aNd bLadE

Ti Length REF mm

53-23210E 10 53-23212E 12 53-23214E 14 53-23216E 16 53-23218E 18 53-23220E 20 53-23222E 22 53-23224E 24 53-23226E 26 53-23228E 28 53-23230E 30 53-23232E 32 53-23234E 34 53-23236E 36 53-23238E 38

Ti Length REF mm

53-27610E 10 53-27612E 12 53-27614E 14 53-27616E 16 53-27618E 18 53-27620E 20 53-27622E 22 53-27624E 24 53-27626E 26

Ti Length REF mm

53-27116E 16 53-27118E 18 53-27120E 20 53-27122E 22 53-27124E 24

53-27126E 26

For the 2.0mm Locking Pegs, please use the fol-lowing 2.0mm drill ref: 60-20185, 60-20385 and 60-20485.


For the 2.7mm Locking Screws, please use the fol-lowing 2.0mm drill ref: 60-20185, 60-20385 and 60-20485.

For the 2.7mm Partially Threaded Screws, please use the following 2.0mm drill ref: 60-20185, 60-20385 and 60-20485.

2.3MM LOcKING ScREwS

Ti Length REF mm

53-23610E 10 53-23612E 12 53-23614E 14 53-23616E 16 53-23618E 18 53-23620E 20 53-23622E 22 53-23624E 24 53-23626E 26 53-23628E 28 53-23630E 30 53-23632E 32 53-23634E 34 53-23636E 36 53-23638E 38

For the 2.3mm Locking Screws, please use the following 1.9mm drill ref: 60-19140, 60-19340 and 60-19440.

2.7 MM PaRTIaLLY THREadEd LOcKING ScREwS

Ti Length REF mm

53-27716E 16 53-27718E 18 53-27720E 20 53-27722E 22 53-27724E 24

53-27726E 26

For the 2.7mm Partially Threaded Locking Screws, please use the following 2.0mm drill ref: 60-20185, 60-20385 and 60-20485.

2.7MM NON-LOcKING ScREwS

Ti Length REF mm

53-27210E 10 53-27212E 12 53-27214E 14 53-27216E 16 53-27218E 18 53-27220E 20 53-27222E 22 53-27224E 24 53-27226E 26




Ordering Information – Instruments Ordering Information – Plate Trials

REF Description

54-25384T Volar DR Trial, Narrow, Right, Short

54-25374T Volar DR Trial, Narrow, Left, Short

54-25386T Volar DR Trial, Standard, Right, Short

54-25376T Volar DR Trial, Standard, Left, Short

54-25440T

54-25442T

54-25444T

54-25446T

XXL Volar DR Trial, Narrow, LE (11 holes)

XXL Volar DR Trial, Narrow, RI (11 holes)

XXL Volar DR Trial, Narrow, LE (8 holes)

XXL Volar DR Trial, Narrow, RI (8 holes)

REF Description

aNaTOMIcaL vOLaR PLaTE TRIaLS

uNIvERSaL vOLaR PLaTE TRIaLS

dORSaL PLaTE TRIaLS

xxL aNaTOMIcaL vOLaR PLaTE TRIaLS

REF Description

54-25394T Volar DR Trial, Narrow, Short

54-25396T Volar DR Trial, Standard, Short

54-25395T Volar DR Trial, Narrow, Long

54-25397T Volar DR Trial, Standard, Long

FRaGMENT SPEcIFIc PLaTE TRIaLS

REF Description

54-25400T Lateral DR Trial, Short

54-25402T Dorsal Medial DR Trial, Short, Right

54-25403T Dorsal Medial DR Trial, Short, Left

REF Description

54-25290T Dorsal DR Trial, Standard, Right

54-25291T Dorsal DR Trial, Standard, Left

54-25292T Dorsal DR Trial, Wide, Right

54-25293T Dorsal DR Trial, Wide, Left

INSTRuMENTaTION

REF Description

07-30600

07-30111

07-10006

07-10021

07-10175

43-09830

64-00011

Lobster Bone Holding Forceps

Lewin Bone Holding Forceps,Sharp Tip

Elevator, Double sided, Narrow&Wide, Hohmanns

Elevator, Double sided, Strong&Light Curved

Bone Hook

Mallet (250g)

Tamp

bONE REducTION INSTRuMENTS

29-27001

29-27002

29-27003

29-27004

VariAx Distal Radius Locking Implant Module, double-sized

Inlay for Anatomical Volar Distal Radius Plates

Inlay for Universal Volar Distal Radius Plates

Inlay for Volar Anatomical XXL DR Plates

REF Description

IMPLaNT MOduLE

29-13012

29-13013

29-13114

29-13024

VariAx Lid for Sterilizing Container

Sterilizing Container, Half-size, w/o VariAx Lid

VariAx Distal Radius Plating Instrument Tray

VariAx Distal Radius Bone Reduction Tray

REF DescriptionSTERILIzING cONTaINER

56-4028107-40281

K-Wire with Olive Stop *

K-Wire, 1.1x160mm **

K-wIRESREF Description

* Order Quantity: Packages of 5** Order Quantity: Packages of 10

dEPTH GauGES

REF Description

62-00018

62-00016

VariAx Distal Radius Depth Gauge for 2.3/2.7 mm Screws, black

Depth Measuring Gauge

REF Description

62-20290 Screwdriver Ratcheting Handle

56-01250 Polyaxial Drill Guide 2.3mm/2.7mm 56-01255 Fixed Angle Drill Guide 2.3mm/2.7mm 56-01260 2.3mm Overdrill and K-Wire Guide 64-20117 Plate Bending Pliers 64-20118 K-Wire Bending Pliers 64-20129 Forceps with Grasping Lips

x-RaY TEMPLaTES

62-90004

62-90005

62-90002

62-90003

62-90000

62-90001

X-Ray Template XXL Volar DR Plates (Scale 1:1)X-Ray Template XXL Volar DR Plates (Scale 1.15:1)X-Ray Template Volar DR Plates (Scale 1.15:1)X-Ray Template Dorsal DR Plates (Scale 1.15:1)X-Ray Template Volar DR Plates (Scale 1:1)X-Ray Template Dorsal DR Plates (Scale 1:1)

REF Description

REF Description

50-23501 Marker - Locking Screws 2.3mm 50-27500 Marker - Locking Screws 2.7mm 50-20501 Marker - Locking Pegs 2.0mm 50-23001 Marker - Bone Screws 2.3mm 50-27000 Marker - Bone Screws 2.7mm 50-27001 Marker - PT Bone Screws 2.7mm 50-27501 Marker - PT Locking Pegs 2.7mm 50-23502 Marker - 2.3mm

MaRKERS

Plates and Screwsdownload.breakpoint.sk/_timed/27-34.pdf · · 2013-01-03Plates and Screws axSOS...

Documents

Transcript of Plates and Screwsdownload.breakpoint.sk/_timed/27-34.pdf · · 2013-01-03Plates and Screws axSOS...