Plasma air -model afs-mf-JB ionization Product suBmittal€¦ · The AFS-MF-JB can be installed in...
1
Plasma air - model afs-mf-JB ionization Product suBmittal SPECIFICATIONS Material: . . . . . . . . . . . . . . . . . . . . . . . . 16 gauge steel Finish: . . . . . . . . . . . . . . . . . . . . . . . . . . Heat cured powdercoat Gasket: . . . . . . . . . . . . . . . . . . . . . . . . . Neoprene EPDM Weight: . . . . . . . . . . . . . . . . . . . . . . . . . 2 pounds Maximum Operating Temperature: 140º F (60º C) Electrical: Voltage: . . . . . . . . . . . . . . . . . . . . . . . 115V/230V Power Consumption: . . . . . . . . . . 20 watts max Current Draw: . . . . . . . . . . . . . . . . . 0.2 amp max Frequency: . . . . . . . . . . . . . . . . . . . . 50/60 hertz Field Electrical Connection: . . . . . Junction Box DIMENSIONS: See Figure 1 Ionization units should be powered when there is air flow in the system. The Plasma Air Model AFS-MF-JB provides a convenient method for powering Series 100 and 200 Ion- ization Units. The AFS-MF-JB is equipped with a pressure switch which closes at 0.05 inch WG. The unit can be used on either positive or negative pressure ducts. The AFS- MF-JB can be installed in metal duct utilizing the factory supplied gaskets and pre-drilled flange. The unit is shipped complete with an electrical “jumper cord” and (4) 4 mm mounting screws to mount the ionization unit to the AFS-MF-JB frame. The frame is mounted to the duct with sheet metal screws. model afs-mf-JB model 100 mounted in afs-mf-JB Plasma air international 35 melrose Place, stamford, ct 06902 203-662-0800 ph 203-662-0808 fax www.plasma-air.com [email protected] 11 3/4” DUCT CUT-OUT DIMENSION 10” X 7” MOUNTING SCREW LOCATION (TYP. FOR 4) JUNCTION BOX SHEET METAL SCREW LOCATION (TYP. FOR 8) FACTORY SUPPLIED GASKETS DRAWING NOT TO SCALE DIMENSIONS PRESSURE SWITCH PLASTIC TUBE JUMPER CORD JUMPER CORD REFERENCE PRESSURE PORT 9” FIGURE 1 © 2012 All rights reserved
Transcript of Plasma air -model afs-mf-JB ionization Product suBmittal€¦ · The AFS-MF-JB can be installed in...
Plasma air-model afs-mf-JB ionization Product suBmittal
SPECIFICATIONSMaterial: . . . . . . . . . . . . . . . . . . . . . . . . 16 gauge steelFinish: . . . . . . . . . . . . . . . . . . . . . . . . . . Heat curedpowdercoatGasket: . . . . . . . . . . . . . . . . . . . . . . . . . Neoprene EPDMWeight: . . . . . . . . . . . . . . . . . . . . . . . . . 2 poundsMaximum Operating Temperature: 140º F (60º C)Electrical:Voltage: . . . . . . . . . . . . . . . . . . . . . . . 115V/230VPower Consumption: . . . . . . . . . . 20 watts maxCurrent Draw: . . . . . . . . . . . . . . . . . 0.2 amp maxFrequency: . . . . . . . . . . . . . . . . . . . . 50/60 hertzField Electrical Connection: . . . . . Junction Box
DIMENSIONS: See Figure 1
Ionization units should be powered when there is air flow
in the system. The Plasma Air Model AFS-MF-JB provides
a convenient method for powering Series 100 and 200 Ion-
ization Units. The AFS-MF-JB is equipped with a pressure
switch which closes at 0.05 inch WG. The unit can be used
on either positive or negative pressure ducts. The AFS-
MF-JB can be installed in metal duct utilizing the factory
supplied gaskets and pre-drilled flange. The unit is
shipped complete with an electrical “jumper cord” and (4)
4 mm mounting screws to mount the ionization unit to the
AFS-MF-JB frame. The frame is mounted to the duct with
sheet metal screws.
model afs-mf-JB
model 100 mounted in afs-mf-JB
Plasma air international 35 melrose Place, stamford, ct 06902 203-662-0800 ph 203-662-0808 fax www.plasma-air.com [email protected]
11 3/4”
DUCT CUT-OUTDIMENSION 10” X 7”
MOUNTING SCREWLOCATION (TYP. FOR 4)
JUNCTION BOXSHEET METAL SCREWLOCATION (TYP. FOR 8)
FACTORY SUPPLIED GASKETS
DRAWING NOT TO SCALE
DIMENSIONS
PRESSURESWITCH
PLASTIC TUBE
JUMPER CORD
JUMPER CORD
REFERENCEPRESSURE PORT
9”
FIGURE 1
© 2012 All rights reserved
