placi_osb_catalog_general_en_49632.pdf

8/9/2019 placi_osb_catalog_general_en_49632.pdf

1/28

EGGER CONSTRUCTION

Wood based panels for useintimber construction

PROFESSIONAL

www.egger.com


2/28

Architects, Joiners and Home owners appreciate thebeauty, flexability and advantages of using woodas a building material. Engineered wood productsmade by EGGER fulfil these expectations.


3/28

EGGER CONSTRUCTION MORE FROM WOOD

WITH A TOTAL OF PLANTS, EGGER RANKS AMONGST

THE LEADING PRODUCERS OF WOODBASED MATERIALS

IN EUROPE.

The EGGER group has made it their mission to provide durable wood-based

products and solutions with lasting value for the construction and interior

design industries. Our wood based products are the ideal answer for

construction and decorative applications. Their special characteristics allow

you to plan and carry out work of the highest quality with confidence.

EGGER carefully selects its raw materials and uses state-of-the-art

technology to give its high-quality wood-based materials a new dimension.

This fulfills two market requirements:

Technical construction material with certified performance potential,

which meets all the requirements of CE-marked construction products.

Certified environmentally-friendly wood-based materials e.g. with IBU

environmental product declaration in accordance with ISO .

Our plant in Wismar, Germany has been certified in accordance with

ISO since 2001. Chain-of-custody certificates are available

for the PEFC and FSC systems. EGGER is a global supplier of tested and

certified wood construction products along with an array of other

applications, satisfying system solutions for planners, architects and

fabricators. Committed employees with sales and technical advice are

on hand to provide support for our customers projects.


4/28

EGGER wood-based panels satisfy the needs of the customerthrough high quality, application-optimised panel sizesand by our product experts and logistics service.


5/28

EGGER WOOD CONSTRUCTION

EXTERIOR WALL WITH FUNCTIONS

FACADE SYSTEMS THE CHOICE IS YOURS

INTERNAL WALL

As well as providing reinforcement, EUROSTRANDOSB

also acts as a vapour barrier (sd-value > 2.0 m). In vapour

permeable constructions, there is no need to invest

extra labour on installing a vapour barrier. The OSB-layer

also provides a suffi cient degree of airtightness on patchedjoints, installations and permeations. EGGER DHF is used

on the outside of walls as an external diffusion-open

(sd-value < 0.2 m) and windproof layer behind a ventilated

facade. This protects the structure during the construction

phase, allowing interior work to proceed to schedule. For

constructions with special sound-proofing and thermal

insulation requirements an external layer of EGGER DFF e.g.

beneath larch wood planking is recommended.

We have a variety of interesting cladding options for you to

choose from. From the modern thermal insulation composite

systems (TICS), with a classic rendered facade or a quarter-brick

effect, through curtain wall facades to the popular wooden facades

in the form of laths, planks or shingling. You can have any

colour or type you wish. Even demanding architectural

requirements can be fulfilled using these systems.

Its superb technical properties and varied formats even with

tongue and groove profile make EUROSTRANDOSB ideal for use

in internal walls. With EUROSTRANDOSB it is easy to attach

loads such as cupboards or shelves to the wall surfaces withoutrequiring special dowels. Another advantage of EUROSTRAND

OSB TOP is that it gives you the option of reducing the

distances between the nail and the edge of the board in

question. This allows the wood cross section of the load-

bearing structure to be optimised and thereby reduces the

heat loss through the wooden supporting structure.

TICS (e.g. StoTherm Classic)

Brick cladding with air space

1.Plaster boards

2.Insulated service cavity

3.EUROSTRAND

OSB TOP 15 mm4.Cellulose insulation

5.EGGER DHF 15 mm

6.Vertical lathing

7.Weatherboarding

1.Plaster boards

2.EUROSTRANDOSB TOP 15 mm

3.Cellulose insulation

4.EGGER DFF 30 mm

5.Horizontal lathing

6.Larch wood planking

vapour permeable construction with EUROSTRANDOSB

as interior vapour control layer

easy to make air tight

storey-high sheathing

high loadbearing capacity

Benefits on a view

easy handling

improved noise control

fastening with staples, nails and screws

suitable for hanging shelves

Benefits on a view


6/28

CEILING AND FLOOR CONSTRUCTIONS

DETACHED HOUSE STFLOOR WITH BASIC REQUIREMENTS

CONSTRUCTION WITH ADVANCED REQUIREMENTS APARTMENT BUILDING

The quality of living spaces depends on the quality of the

sound insulation. A well planned construction can prevent

any undesired influences and disturbances. The minimum

requirements are set out in the relevant standards. Additional

sound proofing requirements must be specially agreed with thedeveloper.


2.Concrete blocks

3.Impact sound insulation board


5.Still air layer

6.Mineral fibre

7.Cross joists

8.Plaster boards 12.5 mm


2.Mineral fibre

3.Expanded perlite filling

4.Sisalit trickle protection


6.Still air layer

7.Mineral fibre

8.Resilient channel


At a centre-to-centre span greater

than 62.5 cm (i.e. reconstruction of

old buildings) for a fire resistance of

30 minutes EUROSTRAND

OSB TOP, 30 mm, T&G, size

3000 1250 mm is recommended.

Benefits on a view

Sound insulation products for the use in timber floors

provide an acoustic impedance refered to length

of r > kN s/m

Note


7/28

FLOATING FLOOR WITH EGGER DFF ANDEUROSTRANDOSB

FULLYINSULATED PITCHED ROOF MODERN ROOF STRUCTURE WITH EGGER DFF WOOD FIBRE INSULATION

CONVENTIONAL STRUCTURE WITH ESSENTIAL SARKING MEMBRANE

FLOATING FLOOR WITH EUROSTRAND OSB

With a measured reduction in impact

noise Ln,w = 20 dB in solid ceilings in

accordance with DIN EN ISO - and

excellent Ln,w = 7 dB in wood-beamceilings following DIN EN ISO -,

EGGER DFF boards, in conjunction with

15/18 mm OSB flooring boards, are also

suitable for floating floor systems on new

builds, restorations and renovations.

Here the circumferential tongue and

groove profile allows for easy, tight,

installation of the boards for uniformly

high sound protection. With dimensions

of 2.50 0.675 m, the EGGER DFF boards

are very easy to use even in existing

buildings due to their light weight(14 kg/board).

Of all construction elements, the roof

is the most exposed to weather and

environmental influences. Its design and

construction are therefore of particular

importance. EGGER offers two system

solutions for this field of application.

EGGER DFF as rigid underlay is ideal for

thermal and sound insulation require-

ments, while EGGER DHF is perfect for

additional structural and fire protection

requirements. Use of loft space as living

quarters places whole new demands on

roofs. Requirements such as summer

overheating protection, thermal

insulation in the winter, as well as

appropriate sound proofing and fire

protection can easily be met.

U value = 0.18 W/mK

Phase shift 8 hours

U value = 0.35 W/mK

Phase shift 7 hours

1.Floor covering


3.EGGER DFF 30 mm

4.Floor load (e.g. footpath flagstones)

5.Structural ceiling



3.Mineral fibre

4.EGGER DFF 30 mm

5.Counter lathing

6.Cross joists

7.Roofing tiles

1.Cement lime plaster

2.HWL board

3.Mineral fibre

4.Still air layer

5.Sarking membrane

1.60 m

6.Counter lathing

7.Cross joists

8.Roofing tiles

The use of EGGER DHF/DFF reduces

thermal bridges effect of the rafters.

Improvement of the summer heat

protection and the noise control. Easy and quick installation supported

by nailing lines at the surface.

Benefits on a view


8/28

Airtight roof construction


9/28

SPECIAL APPLICATIONS

ROOF CONSTRUCTIONS FOR HALLS WITH

REQUIREMENTS TO FIRE RESISTANCE

METAL ROOF COVERING ON EUROSTRAND OSB

Roof constructions with metal covering and a subconstruction

made of OSB boards have been successfully used for several

years. Tests carried out by WKI Braunschweig on the withdrawal

strength of fasteners and by I.F.I. Aachen on durability

properties under dynamic wind loads confirmed the suitabilityof EUROSTRANDOSB E and OSB TOP for this area of

application.

This panel type is offered in particular for the design of roof

and floor constructions with wide spans and requirements of

30 minutes fire protection.

As T&G-panel with the size of 3000 1250 mm the intended

use of this panel is the installation of disk supported

frameworks (roof, floors, walls) with large spans up to 1.50 m

in particular for shop buildings. The panel has an optimal size

of 3.0 m length which reduces waste when cutting to size.

Calculated according to EUROCODE EN -- the

EUROSTRANDOSB with 30 mm thickness and a burn-uprate of 0.9 mm/minute provides a fire protection function

of 33 minutes.

NONVENTILATED ROOF STRUCTURE WITHEUROSTRANDOSB E AND/OR OSB TOPNOT TO SCALE

Roof covering with EUROSTRANDOSB TOP

CONSTRUCTION RECOMMENDATIONS

Only use EUROSTRAND OSB E and OSB TOP

Board thickness 22 mm

Recommended board size 2500 1250 mm

Fasten the wall attachment/diaphragm attachment with

ring nails (stainless steel)

Moisture content of wooden construction (rafter) < 20 %

Upper sided cover over the OSB with structured underlay,

improves sound-proofing by up to 6 dB Correct construction planning and execution with regard

to thermal insulation and moisture protection

Observe any fire protection requirements

(airborne ember and radiating heat)

Observe the recommendations of the metal roof

and membrane manufacturers!

1. Metal roof (double skin partition)

2.Structured separation layer (e.g. Delta by Drken)

3. 22 mm EUROSTRANDOSB TOP4.Rafters

5. Thermal insulation 200 mm

6.Vapour barrier in accordance with meltwater calculation

7. EUROSTRANDOSB E or OSB TOP 15 mm

8.Plasterboard (optional)


10/28

The assembly hall of the Pilatus Aircraft Ltd. inStans, Switzerland, with an area of 8800 m is builtalmost completely out of wood. The decision to useEUROSTRANDOSB TOP and EGGER DHF as structuralsheathing of wall and roof beneath faade and metalroof cover was taken because of the outstandingtechnical performance of these panels.


11/28

Our plant in Wismar, Germany has been certified in accordancewith ISO since 2001.

Most modern technology: With our 38.7 m ContiRoll we guaranteeflexibility and variety of panel sizes up to 11.5 2.8 m.

EGGER ENGINEERED WOOD PRODUCTSFOR USE IN CONSTRUCTION

EUROSTRANDOSB is the right choice as a supporting and

bracing element for walls and ceiling elements for all constructive

applications with high load-bearing and dimensional stabilityrequirements. Specially matched to the relevant field of

application, the strength classes OSB/ and OSB E are

available in accordance with EN and OSB TOP (with

formaldehyde-free adhesive) in accordance with building

regulations approval Z-.-. The separate strand preparation

for the surface and core layers, the specific strand geometry

and a high degree of orientation of the strands ensures optimum

technical properties and the highest possible degree of safety

in construction planning.

EUROSTRANDOSB

SERVICE CLASS

TONGUE AND GROOVE PROFILE

According to ENV -- (EC) EUROSTRANDOSB E,

OSB TOP can be used in service class (dry conditions) and

(humid conditions), and EUROSTRANDOSB/ in service class .

The asymmetrical, conical tongue and groove profile of the

board and cladding panel guarantees exact and rapid construction

of floors, roofs and walls and the required stress transfer on

braced (diaphragm action) board connections. In addition, it

also improves the windproofness of the construction.

In the context of the permission was regulated:

Design values for fasteners like screws, staples, and nails.

That enables to design the distribution of loads directly into

the EUROSTRANDOSB TOP panels.

Structural glueing of the unsanded panels at edge and surface

with approved PU glue from the Purbond HB product range

(type HB , , )

Note


12/28


13/28


14/28

Thickness [mm]Strength values [N/mm]

Bending Tension Compression Panel shear Planar shear

tnom fm ft fc fv fr

. . . .

Thickness [mm]Mean stiffness values [N/mm]

Bending Tension Compression Panel shear Planar shear

tnom Em Et Ec Gv Gr

Thickness [mm] Mean stiffness values [N/mm]

tnom fh

.

Load durationclass

kmod kde f

SC SC SC SC

medium . .

. .short . .

instantaneous . .

Property Standard Unit Value

Density EN kg /m

Diffusion resistance /Sd- Wert EN - /m /.

Thermal conductivity nominal value D EN W/mk .

Thermal conductivity calculated value R EN W/mk .

Thermal resistance R EN mK/W .

Specific heat capacity c EN J/kgK

Building materials class DIN - B normal flammability

Reaction to fire (Euroclass)) EN - C-s, dFormaldehyde emission EN mg / g atro . (E < . ppm)

Calculated values for the modification factor kmodand the deformation coefficient kdef,

in accordance with DIN :-, type MBH.LA table F and F

CHARATERISTIC VALUES FOR STRENGTH AND STIFFNESS

*in accordance with WKI-testreport, no. B /

Static design according to Eurocode .The modification factor kmodand thedeformation coefficient kdefcan be used forstatic measurement in accordance withEurocode (EN --:) in:SC = service class = dry conditions andSC = service class = humid conditions.

The properties and characteristics of EGGER DFF fulfill the requirements of EN :.Thermal insulation products for buildings Factory-made wood-fibre [WF] products andtherefore it bears the CE marking.

EGGER DFF VAPOUR PERMEABLE, MOISTURE REGULATING WOOD FIBREBOARDS

DFF was specially designed by EGGER for use as a vapour

permeable light exterior cladding for roof and wall construction.

When used as a sub-roof board all of its advantages become

obvious. Here the board can be used as a second water-bearing

layer. Its useful insulating properties help protect against

summer heat input in the construction and improves the noise

control of the structure. EGGER DFF boards have been tested for

use as impact sound insulation boards under floating

EUROSTRAND OSB boards. Further application examples can

be found in this brochure on page 4/5.

EGGER DHF IN ACCORDANCE WITH Z.

CALCULATION VALUES WITH RESPECT TO BUILDING PHYSICS AND CHARACTERISTICS

EGGER DFF ACC. TO EN


15/28

max. 80 cm

Remove the steel bands on site

Package protected by film cover

For acclimatisation on site:Boards secured in the corner of a room

For acclimatisation on site:Boards propped up by battens

Vapour permeable and airtight constructionsprovide a long life span of the building.

PROCESSING RECOMMENDATIONS

The following instructions also apply to EUROSTRANDOSB,

EGGER DHF and EGGER DFF. These are essential for correct

use of the boards.

STORAGE AND TRANSPORT

Correct storage and protective measures during transport areessential for problem-free handling. The following simple

principles should be taken into account:

EUROSTRANDOSB, EGGER DHF and DFF boards should be

stored flat on several pieces of squared timber. The span

width should be no greater than 80 cm and the pieces of

squared timber should all be the same height. If several pallets are stacked on top of each other then

the squared timber should be aligned by height. Steel bands should be undone immediately in the fabricators

storeroom to prevent compressive strain on the pallet.

Upright storage (practically vertical) is only suitable for asmall number of boards on a dry floor. Tongue and groove

boards In this case, only stand them on the groove side. In the case of transport by forklift truck the squared timber

chosen must be suffi ciently high so as to prevent damage. The boards must be suffi ciently protected against weathering

before being packed (closed lorry tarpaulin, polythene

sheeting). Storage rooms should be uniformly air conditioned and free

from large moisture and temperature fluctuations. Before using the boards, a 48-hour period is recommended

to allow the wood to acclimatise to local humidity.


16/28

Relative humidity (RH) at C Wood-based material approx. equilibriummoisture Application

Service class , % to %Dry conditions

% to %Installed dry,no moisture during usage.

Service class , % to %Humid conditions % to %

Occasional increase in humidity during use;Installed externally under roof. No directweathering.

MOISTURE PROTECTION

EUROSTRANDOSB is characterised by low thickness swelling

and a high degree of dimensional stability (see technical data:

dimensional changes under influence of moisture). When used

as a supporting and bracing element, appropriate measures

should be taken against weathering. According to EN/TS wood and wood-based materials with the following equilibrium

moistures (see table) are fit for use if installation is carried out

correctly and no impermissible condensation can form.

Dry screeds consisting of wood-based materials should only

be laid in enclosed buildings once windows and doors have

been fitted. When installation is carried out in rooms without a cellar

below, ensure suffi cient thermal insulation to prevent

condensation forming on the underside of the board and

possible warpage to the floor. In the case of concrete ceilings install a vapour barrier first.

PE film with d > 0.2 mm which overlaps joints by 30 cm and

can be installed right up to the upper edge of the floor is

suitable.

The board moisture should correspond to the local humidity

where it will be installed. In the case of floor joists made of dry wood note that u < 15 %,

since shrinkage of the subconstruction can result in long-term

squeaking noises. When using wet construction materials, such as plaster,

paint and wallpapering the resulting high humidity should be

dispersed by adequate ventilation or other suitable means.

Wood and wood-based materials must not take in moisture

from the surrounding construction components. If the floor cannot be immediately installed after the dry

screed has been laid then the board surface must be covered

with a PE film or other suitable material to prevent it drying

out or becoming more moist on one side, leading to

deformation (cupping, buckling).

EQUILIBRIUM MOISTURE OF WOODBASED MATERIALS

The use of EUROSTRANDOSB as a vapourcontrol layer at the inside of vapour permeableconstructions guarantees a suffi cient highsafety against condensation risk.

Board thickness

Board type/permissible service class

Compliance mark

CE marking

Before installation the following should be inspected on site:


17/28

> dn

EUROSTRANDOSB TOP > dnOSB/, OSB/ > dn

dnNail diameter

dn

dn

Installation

Fastening recommendation for nonload-bearing EUROSTRANDOSB,EGGER DHF and DFF boards

DISPOSAL

SAW DRILL MILL

FASTENING

IF BOARDS WILL BE VISIBLE ONCE INSTALLED,NOTE THE FOLLOWING FOR A GOOD CUT:

In its delivery condition, wood waste can be used as a material

or for the production of energy. In this case it is classified according

to Appendix III of the Waste Wood Ordinance to (EWC Codes)

, or . According to the waste code, it will be

decided by local waste laws what form the disposal will take.

EUROSTRANDOSB can be sawn and milled like solid wood

using conventional electrical hand tools. We recommend the

use of hard-metal cutting tools.

EUROSTRANDOSB can be attached with all fasteners suitable

for chipboard, such as screws, staples and nails. The length of

the nail/screw should be 2.5 board thickness and at least

50 mm. With staples, a minimum wire gauge of 1.53 mm should

be used. Corrosion resistant fasteners, e.g. made from galvanised

or stainless steel, are to be used. Due to the high withdrawal

strength, only flat-head nails with gutter groove, screw nails or

annularly threaded nails should be used (see also DIN -).

The crosswise orientation of the strands in the EUROSTRAND

OSB creates a secure base for the fastener, even in the outer-

most board edge. The thick core-layer structure ensures a high

withdrawal strength around the edges.

Sharp tool Workpiece must not vibrate Correct saw blade overhang

Select a slightly lower feed rate compared to solid wood. Weara respiratory mask if using hand tools without a dust extraction

device. EUROSTRANDOSB can be drilled with all suitable

electronic and manual machines suitable for solid wood.

reduced edge distances for fasteners

EUROSTRANDOSB TOP edge distance > dn

Optimized timber cross sections

Benefits on a view


18/28

EUROSTRANDOSB is the right choice for allapplications with high requirements accordingto load duration and dimensional stability.


19/28


20/28

EGGER DHF AND DFF SPECIAL INSTRUCTIONS

EGGER DHF AND DFF AS SUBROOFING ON THE RAFTERS

UNDERLAY CLASSIFICATION

ADDITIONAL GLUING

EGGER DHF and DFF are vapour permeable underlay boards. They form a second

water-repellent layer under the roof covering. They can be used on roofs with a minimum

pitch of 16 with a max. 8 below the standard roof pitch (SRP) of the planned roof

decking. They are installed with the tongue and groove joints from the eaves to the

roof ridge, with tongues pointing towards the ridge. In the case of a shortfall of morethan 8 the standard roof pitch must be a rain and water tight subroof. With a board

thickness 15 mm EGGER DHF, as rafters, is walkable up to a rafter grid of m acc. to

ONR - (dry board). This does not apply to EGGER DFF.

As interlocked underlay (boards with circumferential tongue and groove profile), the

boards are assigned to Class 3 according to the ZVDH guidelines. EGGER DHF and

EGGER DFF can be installed without an additional nail sealing strip under the counter-

batten and without taping the tongue and groove joint, even in case of elevated

requirements and with a roof pitch up to 8 less than the regulation pitch. Compliance

with the minimum roof pitch of 16 is mandatory. Openings (for chimneys etc.) and

joints (covings, groins, dormers etc.) must be taped using suitable adhesive tape.

A taped underlay must be implemented when the roof pitch is less than the regulation

pitch of 16 by a maximum of 8. All board joints are taped using suitable adhesive

tape. The minimum roof pitch is 10.

Increased requirements in addition to shortfall of standard roof pitch:

Use of attic, especially as living space Special construction features, e.g. dormer windows, ridges, complicated roof shapes Climatic factors, e.g. mountains or coasts Local requirements, e.g. from building control

UNINSULATED COCKLOFT

TRANSIENT WEATHERING

The roof area of an uninsulated cock-loft and an unconverted attic must also be

ventilated even by using a vapour permeable sub-roofing material. The recommended

ventilation cross-section, derived from the regulations for the ventilation of flat roofs

is 200 cm per running meter at the ridge and the eaves.

After installing EGGER DHF and DFF the roof covering/facade should be fitted

immediately. Between March and November the boards can be exposed to natural

weathering for 2 months as a temporary roof. In the winter months, structural

measures must be employed to ensure that the external covering layer of EGGER DHF

cannot freeze, since this would seriously impair the diffusion ability of the external

panelling cladding and potentially lead to moisture damage. In the winter months it

should only be exposed to natural weathering for a maximum of 2 weeks. If EGGER

DHF is used for load-bearing purposes then the moisture protection regulations of the

approval Z-.- apply and DIN -, i.e. the fitted boards have to be protected

from natural weathering.

EGGER DHF/DFFused as rigid underlay

Ventilation of uninsulated cock-loft

During the winter months, icing of

the outer layer of the EGGER DHF

board must be excluded by means

of suitable construction measures,

since this would severely impair the

diffusion characteristics of exterior

sheathing, which may result in

moisture damage.

Note

If the pitch of the roof is less then 8

further measures should be taken

to ensure rain and water tightness

of the roof covering (i.e. taping theEGGER DHF/DFF panel joints).

Note


21/28

Timber studdistance ar(cm) *

Fv(KN/ar) perm iss ible

Wall panels in the height h under horizontal stress

h = . m h = . m h = . m

mm mm mm mm mm mm mm mm mm

. -ar . . . . . . . . .

-ar . . . . . . . . .

. -ar . . . . . . . . .

-ar . . . . . . . . .

. -ar . . . . . . . . .

-ar . . . . . . . . .

. -ar . . . . . . . . .

-ar . . . . . . . . .

DIMENSIONING

Wooden structures are designed according to the appropriate National and European

standards. In the medium-term, Eurocode has been introduced as an EU-wide

regulation for the design of wooden constructions. Characteristic values for the

structural design of EUROSTRANDOSB in accordance with Eurocode can be

taken from DIN EN - or from the building authorities.

The following assessment tables were created using the regulations for EUROSTRAND

OSB TOP in accordance with approval Z-.- as well as the rules for the assessment

of wooden constructions in accordance with Eurocode .

LOADING TABLES FOR EUROSTRANDOSB

PREDIMENSIONING OF WALL PANELS FOR HORIZONTAL FORCE

The calculation is based on the regulations in DIN -:, section: .. on the

testing of tensile force on the board. To prevent the planking from buckling, the timber

stud distances should be limited to ar= 83.3 cm.

* Panel with one, two or three timber stud distances ar.In the case of double-sided planking, double the permissible Fv(KN/ar) values.

WALL PANELS IN THE HEIGHT H UNDER HORIZONTAL STRESS

Horizontal force allowable Fv(KN/ar)

ASSUMPTIONS

The longitudinal edge of the board runs parallel to the wall studs. There are no

horizontal joints in the area. The nailing is carried out using staples with 1.8 mm wire

gauges with a length of 55 mm and a clearance of 50 mm; N1 = 280 N permissible.

The tables contain recommended

values and are not intended as a

substitute for individual verification

by a structural engineer.

Note


22/28

Needed board thickness d (mm)

qk/ Qk . / . . / .

gk gk

ar(cm) . . . . . .

.

.

.

.

.

.

.

.

. 40

Edge Condition: b = 1,25 m Individual load flat taken

PREDIMENSIONING OF HORIZONTAL PLANKING AS DOUBLESPAN BEAM FOR VERTICAL LOADS

The following table specifies the required board thickness with the application of vertical loads only

(e.g. shelving, sheathing wood beam layer) without plate effect, dependent on the ridge retention ar.

PREDIMENSIONING OF SINGLE GIRDER WITH EUROSTRANDOSB E

Needed board thickness d (mm)

qk/ Qk . / . . / .

gk gk

ar(cm) . . . . . .

.

.

.

.

.

.

. * *

. * * * * *

. * * *

. * * *

Edge Condition: b = 1,25 m Individual load flat taken

PREDIMENSIONING OF SINGLE GIRDER WITH EUROSTRANDOSB TOP


23/28


24/28

EGGER DHF as structural sheathing, up to3.0 m storey high sheathing in classifiedwall structure REI acc. to EN -


25/28

Timber studdistances ar(cm)

Fv(KN/ar) pe rm iss ib le

Wall panels in the height h under horizontal stress

h = . m h = . m h = . m mm mm mm mm mm mm

.* -ar . . . . . .

.** -ar . . . . . .

EGGER DHF

PREDIMENSIONING OF WALL PANELS

ASSUMPTIONS

The following design tables are based on one-sided external panelling of the

supporting structure using EGGER DHF. The calculated values for humid conditions

(service class ) are used. The calculations were carried out in accordance with the

regulations set out in DIN -:-, .., on the testing of tensile force onthe board.

The longitudinal edge of the board runs parallel to the wall studs. There are no

horizontal joints in the area.

The nailing is carried out using clips with 1.53 mm wire gauges with a length of

55 mm and a clearance of 50 mm; N1= 250 N permissible.

Sheathing thickness d=13mm/15mm (0.51 / 0.59)

* Panel with two timber stud distances ar.** Panel with three timber stud distances ar.

IMPORTANT DOCUMENTS AND STANDARDS

Additional processing instructions and application examples

can be found at/in:

www.egger.com

Eurocode EN -- Timber construction in conjunction

with the nationally applicable usage document (national

timber construction standard)

EN/TS Wood-based panels. Guidance on the use of

load-bearing boards in floors, walls and roofs

The following design tables are

recommendations. They cannot

replace the static calculation by a

permitted civil engineer.

Note


26/28

Picture: Production of export cases made ofEUROSTRAND OSB according to ISPM Standard

Picture: Shelf and storage system Schottelcompany, Wismar, EUROSTRAND OSB TOP

Picture: Airport Munich, Terminal 2,EUROSTRAND OSB E, 20 mm, as concrete shuttering

Picture: I-beam production with EUROSTRANDOSB E


27/28

We reserve the right to make changes to the stock program.

*on request (by load)

** Delivery by request, production as individual customer order 250 m (8,829 cubic feet)

Product/

length width (mm)

Board thickness d (mm)

EUROSTRAND OSB TOP Z-.-

Straight edge unsanded

* *

*

*

**

T&G unsanded

T&G sanded

T&G unsanded

**

EUROSTRAND OSB E EN


* * * *

* *

*

** ** *

T&G unsanded

T&G sanded

T&G unsanded

EUROSTRAND OSB/ EN


EGGER DHF underlay boards acc. to Z-.- / EN - MDF.RWH

T&G unsanded

T&G unsanded

EGGER DFF insulating boards acc. to EN

T&G unsanded

STOCK PROGRAM EUROSTRANDOSB AND EGGER DHF AND DFF / PLANT WISMAR


28/28

alterations.

Withoutguaranteeforprintingerrors,

standarderrorsand

mistakes.

www.egger.com

Distributed by:

FRITZ EGGER GmbH & Co. OG

HolzwerkstoffeWeiberndorf 20

6380 St. Johann in Tirol

Austria

+43 50 600-0

+43 50 600- 10111

[email protected]

EGGER Holzwerkstoffe

Wismar GmbH & Co. KG

Am Haffeld 1

23970 Wismar

Germany

+49 3841 301-21260

+49 3841 301-61260

[email protected]

EGGER (UK) Limited

Anick Grange Road

Hexham, Northumberland

NE46 4JS

United Kingdom+44 1434 602191

+44 1434 605103

[email protected]

placi_osb_catalog_general_en_49632.pdf

Documents

Transcript of placi_osb_catalog_general_en_49632.pdf