PK-232/DSP MULTI-MODE CONTROLLER OPERATION

Welcome to the world of Digital Signal Processing. You may be acquainted with DSP in your new radio,or you may have a Timewave Technology DSP unit in your shack. Now you have DSP capability foryour PK-232 digital modes. Here are the most frequently Asked Questions (FAQ’s) we have been get-ting.

What exactly have I bought? The DSP board you have installed provides a proven set of DSP BrickWall data filters to your PK-232MBX. These are:

45 Baud Baudot Twin Peak filter for RTTY100/200 CW filters (Jumper selected, Shipped with jumper on, set at 200)100/200 Adaptive PACTOR filters100 Baud AMTOR/NAVTEXT300 Baud HF Packet1200 Baud UHF/VHF PacketEuropean/American Tone Set (Jumper selected, Shipped with jumper off, American Tones)WEFAXSIAM

Can I use my existing software? In a word, YES. The new firmware provides all the control necessaryto select the proper filter, even switching between 100 and 200 baud PacTOR filters as the PK-232/DSPchanges the baud rate to accommodate changes in the transmission path.

What should I expect from the new board? DSP provides sharper skirts that reduce the noise in theband pass as well as rejecting interference from adjacent signals. In RTTY this can improve error ratesup to 100 times in weak signal and noisy environments. Tune slowly, signals will appear to just pop outof the noise. We suggest you start with a fairly wide filter setting in your radio and cascade that with thenarrower filter of the Multi-Mode Controller.

What else has changed? The small red LED on the board will light when a signal overloads the DSPinput (Note that a remote light can be tied to Jumper next to the overload LED). The startup sequence isalso new, notice that an extra set of lights blink during startup. This tells you the version 7.2 firmware isinstalled.

Timewave TechnologyVisit our web page: http://www.timewave.com to download a demo copy of our PK-Term’99 program.

A.06227

Timewave Technology Inc.501 W. Lawson Ave.St. Paul, MN 55117 USA

651-489-5080FAX 651-489-5066sales@timewave.com

PLEASE READ THIS BEFORE INSTALLATION

INSTALLATION INSTRUCTIONS ADDENDUM

Before you start the installation on your PK-232MBX upgrade, please inspect the daugh-ter-board. There are 2 28-pin double headers that plug the daughter-board into the PK-232 main circuit board. Take a minute and inspect this header and make sure the pins arenot bent or badly aligned.

When you reach the point in the installation instructions asking you to “place the Pakmaildaughter-board over the standoffs” make very certain that the pins of both headers alignexactly over the main board sockets of U-2 and U-4.

After installing the Pakmail-board double check the alignment. Make certain the first rowof the header pins is in the first row of IC socket holes, not one row behind.

Replacement headers are $6.00 each, plus shipping and handling.

73

Service DepartmentTimewave TechnologyVisit our web page: http://www.timewave.com

Service@timewave.com

A.06227

INSTALLATION INSTRUCTIONSREPLACEMENT OF PK-232 PAKMAIL BOARD

Thank you for purchasing the PakMail Upgrade for your PK-232MBX/HK-232MBX. The followinginstructions are to assist you with the installation of the PakMail daughter-board. Please read theseinstructions completely before beginning this project.

PARTS LIST AND TOOLSYour upgrade kit should contain the following parts:

QTY. PART DESCRIPTION1 PakMail daughter-board w/ Eproms (PK-232DSP-HI, PK-232DSP-LO) ver. 7.22 PK-232MBX Supplements

You will need the following tools to perform this installation:#2 Phillips screwdriverSmall flat-blade screwdriverPencil style soldering ironPortable de-soldering tool (solder remover)¼ inch nut driver –or- ¼ inch wrenchSmall wire cuttersSmall needle-nose pliers

PakMAIL Daughter board Installation

Prepare a clean work area that is as static-free as possible. Be sure to discharge any static build-upyou may have incurred by touching a grounded appliance before proceeding.

CAUTION: When you remove chips and adapters from sockets, DO NOT TRY TO PRY THESOCKET OFF THE BOARD. Be sure that you are working between the chip or adapter and thesocket itself.

STEP 1

Remove the PK-232 top cover by removing the six screws. Set the screws aside for re-assembly.

A.06227

STEP 2

With the front panel of the PK-232 facing you, remove the two screws that hold the old wide stylePakMAIL daughter board in place. Set aside. Unsolder the wire from the daughter board to R-186 at R-186. Using your flat blade screwdriver carefully remove the daughter board from the U-2 and U-4sockets of the motherboard.

STEP 3

A. Locate the 28-to-28 pin adapters in U2 and U4 on the bottom of the old daughter-board and using thesmall flat bladed screwdriver remove both of these and set aside for later use. Inspect these carefullyand make sure the pins are not bent or out of alignment.

B. Locate U5 (at the top of the old daughter board) and carefully remove the memory chip using the flatbladed screwdriver. Note the notch on the IC is oriented toward the left side of the PK-232MBX.This chip will be needed in the next step.

C. Insert the 256K memory chip (Marked 62-256) removed in step B into the socket U5 (Notch to theleft) on the new daughter- board. Make sure that the pins are aligned and the chip is seated com-pletely.

D. Insert the two adapters into U-2 and U-4 on the bottom of the new PakMail daughter-board. Afterinstalling the adapters double-check the alignment. Make certain the first row of the header pins is inthe first row of IC socket holes, not one row behind.

E. Now place the PakMail daughter-board over the standoffs. The two 28-pin plugs on the bottom of thePakMail board will be inserted into the now empty sockets U-2 and U-4. Line up all of the pinsbefore pressing the daughter-board into place. Insert the two screws set aside earlier and tightencarefully. Do NOT over tighten these screws.

F. Locate R-186 on the PK-232 motherboard. Solder the wire from the PakMail daughter-board to theLEFT side of the resister R-186 on the PK-232 motherboard.

F. This completes the installation of the PakMail daughter-board.

You are now ready to install the DSP board.

Should jumper JP-1 be left on or off?

If you are going to be using the program PC-PakRATT for Windows, It is best to leave the battery out ofthe circuit. For all other applications leave the battery in the circuit.

A.06227

PLEASE READ THIS BEFOREDSP BOARD INSTALLATION

INSTALLATION INSTRUCTIONS ADDENDUM

Before you start the installation on your PK-232/DSP upgrade, please inspect the DSPdaughter-board. There is a 40-pin double header that plugs the daughter-board onto thePK-232 main circuit board. Take a minute and inspect this header and make sure the pinsare not bent or badly aligned.

When you reach the point in the installation instructions asking you to “place the DSPdaughter-board over the standoff” make very certain that the pins of the header arealigned exactly over the main board socket U-6.

After installing the DSP-board, double check the alignment of the daughter-board andsocket on the main board. Make certain the first row of the header pins is in the first rowof IC socket holes, not one row behind.

Replacement headers are $8.00 each, plus shipping and handling.

73

Service DepartmentTimewave TechnologyVisit our web page: http://www.timewave.com

Service@timewave.com

A.06227

READ CAREFULLY BEFORE STARTING INSTALLATION

INSTALLATION INSTRUCTIONSPK-232/DSP BOARD

Thank you for purchasing the DSP upgrade for your PK-232MBX. The following instructions are toassist you with the installation of the DSP daughter-board. Please read these instructions completelybefore beginning this project.

PARTS LIST AND TOOLS

QTY PART DESCRIPTION

1 DSP daughter-board (A.06225) 1 Standoff

You will need the following tools to perform this Installation.

#2 Phillips screwdriverSmall flat blade screwdriverNeedle nose pliers Small wire cutters or nippers1/4" nut driverSolder iron or pencil (Do not use a solder gun)Solder

Please take a minute and make certain that the PK-232 you are upgrading is a PK-232MBX. If the unityou have was built as a PK-232MBX (Fig. B) skip to the next paragraph. If you are upgrading a PK-232or PK-232 that has been upgraded to an MBX with an older wide board (Fig. A) you should replace thatboard with the narrow board supplied with this kit. The newer style narrow board is identified by the partnumber A.06239A. After installing the MBX upgrade, test the unit briefly before proceeding with theDSP upgrade.

Prepare a clean work area that is as static free as possible.

IMPORTANT NOTICE

Be sure to discharge any static build-up you may have incurred by touching a grounded appliance beforeproceeding.

1) Remove all cables and power from the PK-232.

2) Remove the top cover by removing the 6 screws from the side and back of the unit. Position the unitwith the front toward you.

3) Determine if you have an old or new style board. Old boards have four 28 pin IC sockets runningdown the left side of the motherboard. New boards have three 28 pin IC sockets running down the

A.06227

left side of the board (see figure B).

4) Locate and remove C-54 (located to the left of the fuse) using the wire cutters or nippers. (see fig. 3)

5) Using the flat blade of the screwdriver, carefully remove U6 from its socket and set aside. (Note howthe chip is oriented in the socket, notch to the left as viewed from the front).

CAUTION: DO NOT TRY TO PRY THE SOCKET OFF THE BOARD. Be sure that you areworking with the EPROM itself.

6) Using the Phillips screwdriver, remove the front center screw from the board and set the screw aside.

7) Install the standoff into the hole in the front where you just remove the screw. Secure the standoffwith the 1/4" nut driver. DO NOT OVER TIGHTEN. This may damage the board or break the standoff.

8) Place the DSP board (part number A.063225) over the U6 socket. Be sure all 40 pins of the DSPboard are aligned with the 40 holes of the socket U6. Press down firmly to seat the DSP board. Recheckthe alignment of the pins into the socket.

9) Secure the DSP board with the screw set aside in step 5. DO NOT OVER TIGHTEN.

10) With the notch to the left, place U6 (removed in step 5) in the socket on the DSP board and Afterchecking U6 to make sure all the pins are correctly aligned, press the chip firmly down. Check carefullythat all pins are in the socket and not folded nor bent).

11) Starting with the left side wire on the DSP board. Attach this wire to R-186 (330 ohms Orange,Orange, Brown). Bend the wire in a “U” around lead of R-186, then press the ends of the “U” togetherusing the needle nose pliers. If your PK-232 board is an “old” style board attach the wire to the left sideof R-186 see fig 1. If your board is a “new” style board attaches the wire to the bottom (Toward thefront) of R-186. Solder the connection. See fig. 2

12) The center wire is attached to the top lead of R-34 (10K ohms, Brown, Black, Orange) see fig. 4.Use the same “U” bend technique to attach the wire that you used on R-186. Solder.

13) T he right side wire is attached to the second pin from the top on the right side of the radio switch(SW2). Again make the “U” bend and attach the wire to the pin, then press the “U” together to make astrong mechanical attachment, Finish by soldering the connection. See fig 5. If the switch in yor PK-232does not have external lugs the wire can be attached to the back pad of C-54 (C-54 was removed in step4)

14) Replace the top cover and install the six screws removed in step 2.

A.06227

U5

U3

U1

Daughter BoarDaughter BoarDaughter BoarDaughter BoarDaughter Boarddddd

DO NOT REMOVE U5(RAM CHIP)

PK-232MBX (HIGH)Ver. X.X

PK-232MBX (LOW)Ver. X.X

Figure A - PK-232 Main board with MBX daughter board installed

Figure B - PK-232MBX Main Board (No MBX daughter board necessary)

PK-232MBX (LOW)Ver. X.X

PK-232MBX (HIGH)Ver. X.X

U2

U3

U6

U6

A.06227

1 1

PK-232 DSP Upgrade AP.06225a

11-Oct-2002

Title:

Size:

TW P/N:

Date:File:

Sheet ofBEngineer:

Project:

Timewave Technology Inc. A. ClarkDSP Daughterboard

PCLK16

IEO18

IEI17

/INT24

A135 A034

/RD5

/INTACK25

/WR6

/CE36

D74 D63 D52 D41 D340 D239 D138 D037

GND7

Vdd23 PA0 33

PA1 32

PA2 31

PA3 30

PA4 29

PA5 28

PA6 27

PA7 26

PB0 8

PB1 9

PB2 10

PB3 11

PB4 12

PB5 13

PB6 14

PB7 15

PC0 19

PC1 20

PC2 21

PC3 22

U1

Z85C36

A932

A1033

A1134

A1235

A1336

A730 A628 A527 A425 A324 A223 A122 A021

BR 18

A831

D178

D189

D1911

D2012

D2113

D2214

D2315

D167

DMS38 PMS37

Vdd 16

BG 40

BMS39

D7 65

D967

D1068

D111

D123

D134

D145

D156

D866

MMAP 17

IRQ2 19

D1 59

D3 61D2 60

D0 58

D6 64D5 63D4 62

CLKIN 42

XTAL 41

CLKOUT 43

DT1 52

TFS1 53

SCK1 56

RFS1 54

Vdd 57

GND 2

GND 10

GND 29

GND 49

Vdd 26

RD45

WR44

DR1 55

DT0 46TFS0 47

SCK0 51

RFS0 48

DR0 50

RESET 20

U2

ADSP-2105

A0 10

A1 9

A2 8

A3 7

A4 6

A5 5

A6 4

A7 3

A8 25

A9 24

A10 21

A11 23

A12 2

A13 26

A14 27

CE 20

OE 22

D011

D112

D213

D315

D416

D517

D618

D719

Vcc28

GND14

Vpp1

U3

27C256

PRE10

CLK11

D12

CLR13

Q 9

Q 8

U5B

74HC74

PRE4

CLK3

D2

CLR1

Q 5

Q 6

U5A

74HC74

G19

DIR1

A02

B0 18

A13

B1 17

A24

B2 16

A35

B3 15

A46

B4 14

A57

B5 13

A68

B6 12

A79

B7 11

VCC 20

GND 10

U474HCT245

Y1

8.192MHz

PCLK 16

IEO 18

IEI 17

/INT 24

A1 35A0 34

/RD 5

/INTACK 25

/WR 6

/CE 36

D7 4D6 3D5 2D4 1D3 40D2 39D1 38D0 37

GND 7

Vdd 23PA033

PA132

PA231

PA330

PA429

PA528

PA627

PA726

PB08

PB19

PB210

PB311

PB412

PB513

PB614

PB715

PC019

PC120

PC221

PC322

J1

DIP40

VCC

C110uF

C2.1uF

C3.1uF

VCC

PA0PA1PA2PA3PA4PA5PA6PA7

PB0PB1PB2PB3PB4PB5PB6PB7

PC0PC1PC2PC3

PA0PA1PA2PA3PA4PA5PA6PA7

PB0PB1PB2PB3PB4PB5PB6PB7

PC0PC1PC2PC3

PC[0..3]

PA[0..7]

PB[0..7]

VCC

C1010nF

D[0..7]

D0D1D2D3D4D5D6D7

D0D1D2D3D4D5D6D7

D0D1D2D3D4D5D6D7

VCC

PB4PB5PB6PB7

PA0PA2PA5

C410nF

C510nF

C610nF

C710nF

VCC

C822pF

C922pF

C1410nF

C131uF

R7

2

L1

FBEAD C151uF

C1610nF

C1810nF

C171uf

VCC

D0

D1R6

1K

R5

1K

JH1

HDR2

DL1

RED

VCC

JH2

HDR2

R9

1K

C22

10nF

JH4

HDR2

13 2

D1BAV99

C201nF

JH3

HDR2

C21

10nF

PK-232 RXD (SW2)

PK-232 Filter (R34)

OVERLOAD INDICATOR

PK-232 RESET

C12

10nF

C1110nF

S06225a.SCH

1 23 45 67 8

JH5

HEADER 4X2

R11K

R21K

R31K

R41K

C23.1uF

VINp 5

SDOFS17

SDI19

SDIFS18

SCLK14

SDO16

VOUTp 1

VINn 6

VOUTn 2

DGND11 AGND2 10AGND1 4

DVdd12 AVdd1 3

REFOUT 7

RESET13

MCLK15

SE20 AVdd2 9

REFCAP 8

U6

AD73311

C1910nF

R810K

VCC