Piston & Turbine Illustrated Tool Catalog
Transcript of Piston & Turbine Illustrated Tool Catalog
![Page 1: Piston & Turbine Illustrated Tool Catalog](https://reader031.fdocuments.in/reader031/viewer/2022020705/61fb95222e268c58cd5fe41a/html5/thumbnails/1.jpg)
3/30/10
Piston & Turbine Illustrated Tool
Catalog
![Page 2: Piston & Turbine Illustrated Tool Catalog](https://reader031.fdocuments.in/reader031/viewer/2022020705/61fb95222e268c58cd5fe41a/html5/thumbnails/2.jpg)
1
![Page 3: Piston & Turbine Illustrated Tool Catalog](https://reader031.fdocuments.in/reader031/viewer/2022020705/61fb95222e268c58cd5fe41a/html5/thumbnails/3.jpg)
2
T-0003 Lead Lag Nut Wrench T-0005 Damper Rod End Removal Tool T-0009 Main Rotor Blade Bolt guide Bullet T-0011 Main Rotor Hoist Sling T-0013 lamiflex Nut Socket T-0014 Needle Point Grease Adapter T-0016 Swashplate Tie-bolt Wrench T-0020 Tail Rotor Blade Nut, A Model T-0022 Collective Capsule Retainer Tool T-0026 Main Rotor Blade Tab Bending Tool T-0027 Main Rotor Blade Tab Angle Tool T-0029 Idler Pulley Installation Kit T-0035 Oleo Holding Tool T-0036 Main Rotor Grip Seal Instalation Tool T-0044 Pulley Alignment Tool T-0045-1 Lower Swashplate Dogleg Puller T-0048 Main Rotor Mast Nut Tool T-0051 Main Rotor Flapping Nut Tool T-0051-A Main Rotor Flapping Nut Tool, ALT T-0054 Swashplate Dogleg Alignment Tool T-0056 Tail Rotor Imput Nut Socket T-0078 Engine Oil Tube Adapter Inst Wrench T-0079-1 Dog Leg Swaging Tools T-0080 TR Transmission Rigging Tool (C & F) T-0086 Upper Guide Tube Retaining Nut Wrench T-0087-15 Tail Rotor Assembly Balance Tool T-0088 TR Drive Shaft Alignment Tool T-0092-5 Taper Pin Removal Tool T-0100-1 Swashplate Bushing Installation Tool T-0102-1 Upper Guide Tube Press Tools
![Page 4: Piston & Turbine Illustrated Tool Catalog](https://reader031.fdocuments.in/reader031/viewer/2022020705/61fb95222e268c58cd5fe41a/html5/thumbnails/4.jpg)
3
NPN Main Rotor Blade Static Balance Tool NPN Main Rotor Shaft TIR Measure Tool NPN Sprag Clutch Purge Tool NPN Fan Shroud Alignment Tool NPN Magneto Spring Installation Tool
T-0104-1 Swashplate DU Bushing Installation Tool T-0111 Correlator Rigging Tool T-0113 Correlator Rigging Tool T-0127 Magnetic Pickup Bracket, 280FX T-0133 Pulley Restraining Tool T-0134 Lower Swashplate Holding Tool T-0135-1 Pinnnion Nut Crowfoot and Adapter T-0136-1 OR Clutch Housing Wrench T-0137 Engine Hoist T-0139-1 Belt Tension Tool T-0141 Drive Pulley Alignment Tool T-0143-1 Tail Rotor Driveshaft Alignment Tool T-0149 Grip Seal Installation Tool T-0151-1 Flapping Bearing Inst Tool, Grease T-0152 Tail Rotor Balance Bracket T-0156 Oil Filler Tube Wrench T-0160-1 Damper Piston / Seal Tool T-0161 U-Block Seal Installation Tool T-0162-1 Flapping Bearing Inst Tool, Oil T-0164-1 Upper Pulley Restraining Tool T-0166-11 Oil Cooler Shaft Alignment Tool T-0168-1 Tail Rotor Blade Assy Holder T-0169-1 Oleo Dissasembly Tool T-0174 T-1575 T-1656-3
Hub Puller Swashplate Centering Tool Blade Weight Removal Tool
T-1709 Upper Swashplate Bearing Tool T-1758 Upper Swashplate Clamping Tool T-1775 Cyclic Centering Rigging Tool T-2889 Tail Rotor Rigging Tool T-2893 Tail Rotor Teeter Bearing Tool T-2896-1 Damper Bleeding Tool Set
![Page 5: Piston & Turbine Illustrated Tool Catalog](https://reader031.fdocuments.in/reader031/viewer/2022020705/61fb95222e268c58cd5fe41a/html5/thumbnails/5.jpg)
4
T-0003
Lead Lag Nut Wrench PISTON & TURBINE
Used to torque lead lag nut on bottom of main rotor hub.
Hub is pictured here up-side-down.
![Page 6: Piston & Turbine Illustrated Tool Catalog](https://reader031.fdocuments.in/reader031/viewer/2022020705/61fb95222e268c58cd5fe41a/html5/thumbnails/6.jpg)
5
T-0005 Damper Rod End Removal Tool
PISTON & TURBINE
Use to remove the rod end from the damper
![Page 7: Piston & Turbine Illustrated Tool Catalog](https://reader031.fdocuments.in/reader031/viewer/2022020705/61fb95222e268c58cd5fe41a/html5/thumbnails/7.jpg)
6
T-0009
Blade Bolt Bullet PISTON & TURBINE
Install on main rotor blade bolt to aid in alignment when installing.
![Page 8: Piston & Turbine Illustrated Tool Catalog](https://reader031.fdocuments.in/reader031/viewer/2022020705/61fb95222e268c58cd5fe41a/html5/thumbnails/8.jpg)
7
T-0011 Rotor Hub Sling
Piston & Turbine
Used to sling Main Rotor Hub.
The entire weight of the helicopter can be lifted off the ground using this method.
![Page 9: Piston & Turbine Illustrated Tool Catalog](https://reader031.fdocuments.in/reader031/viewer/2022020705/61fb95222e268c58cd5fe41a/html5/thumbnails/9.jpg)
8
T-0012, T-0080, T-2889 Tail Rotor Rigging Tool
PISTON & TURBINE
T-0012 used for ‘A’ models T-0080 used for ‘C’ & ‘F’ models T-2889 used for ‘480’ models
80’ Tool shown here
Neutral pedal position.
Full right pedal position Full left pedal position
All of the tools look the same although the dimensions differ between the ‘A’, ‘C & F’ and ‘480’ tools
![Page 10: Piston & Turbine Illustrated Tool Catalog](https://reader031.fdocuments.in/reader031/viewer/2022020705/61fb95222e268c58cd5fe41a/html5/thumbnails/10.jpg)
9
T-0013
Lamiflex Nut Socket PISTON &SOME EARLY 480s
Used to tighten or remove Lamiflex retention nut on piston aircraft and on a few early 480 models
![Page 11: Piston & Turbine Illustrated Tool Catalog](https://reader031.fdocuments.in/reader031/viewer/2022020705/61fb95222e268c58cd5fe41a/html5/thumbnails/11.jpg)
10
T-0014
Needle Point Grease Adapter
Screws on to the grease gun for lubing the TR Spindle Teeter Bearings
![Page 12: Piston & Turbine Illustrated Tool Catalog](https://reader031.fdocuments.in/reader031/viewer/2022020705/61fb95222e268c58cd5fe41a/html5/thumbnails/12.jpg)
11
T-0016 Swashplate Tie-bolt Wrench
PISTON & TURBINE
Used to hold swashplate tie-bolt while assembling lower swashplate assembly.
![Page 13: Piston & Turbine Illustrated Tool Catalog](https://reader031.fdocuments.in/reader031/viewer/2022020705/61fb95222e268c58cd5fe41a/html5/thumbnails/13.jpg)
12
T-0020 A Model Tail Rotor Blade Retention Nut
‘A’ MODEL ONLY
Used to torque the bearing retention nut on narrow chord tail rotors.
![Page 14: Piston & Turbine Illustrated Tool Catalog](https://reader031.fdocuments.in/reader031/viewer/2022020705/61fb95222e268c58cd5fe41a/html5/thumbnails/14.jpg)
13
T-0022 Collective Capsule Restraining Tool
PISTON & TURBINE
Used to hold clutch capsule while installing and removing from the aircraft.
CAUTION: DO NOT ATTEMPT TO REMOVE THE CLUTCH CAPSULE FROM THE AIRCRAFT WITHOUT THE USE OF THIS TOOL, SERIOUS INJURY CAN RESULT!
REMOVING EITHER OF THESE TWO BOLTS WITH OUT THE TOOL INSTALLED CAN RESUT IN SERIOUS INJURY!
![Page 15: Piston & Turbine Illustrated Tool Catalog](https://reader031.fdocuments.in/reader031/viewer/2022020705/61fb95222e268c58cd5fe41a/html5/thumbnails/15.jpg)
14
T-0026 Blade Tab Bending Tool
PISTON & TURBINE
Used to adjust main rotor blade tabs while tracking.
T-0027
![Page 16: Piston & Turbine Illustrated Tool Catalog](https://reader031.fdocuments.in/reader031/viewer/2022020705/61fb95222e268c58cd5fe41a/html5/thumbnails/16.jpg)
15
Blade Tab Angle Tool PISTON & TURBINE
Used To adjust blade tab angles when tracking.
![Page 17: Piston & Turbine Illustrated Tool Catalog](https://reader031.fdocuments.in/reader031/viewer/2022020705/61fb95222e268c58cd5fe41a/html5/thumbnails/17.jpg)
16
T-0029 Idler Pulley Installation Kit
PISTON
Used to support and align the idler pulley while assembling or disassembling.
(Add picture of tool in use)
![Page 18: Piston & Turbine Illustrated Tool Catalog](https://reader031.fdocuments.in/reader031/viewer/2022020705/61fb95222e268c58cd5fe41a/html5/thumbnails/18.jpg)
17
T-0035 Oleo Holding Tool
Used to hold the Seal Housing Assembly while disassembling the oleo
![Page 19: Piston & Turbine Illustrated Tool Catalog](https://reader031.fdocuments.in/reader031/viewer/2022020705/61fb95222e268c58cd5fe41a/html5/thumbnails/19.jpg)
18
T-0036 Main Rotor Grip Seal Installation Tool
PISTON & TURBINE
Used to push the seal into the grip when installing the grip on the spindle.
In most cases the grip can be assembled onto the spindle and the seal gently pried into the grip with a flat screw driver. Use of the tool makes the job easier,
![Page 20: Piston & Turbine Illustrated Tool Catalog](https://reader031.fdocuments.in/reader031/viewer/2022020705/61fb95222e268c58cd5fe41a/html5/thumbnails/20.jpg)
19
T-0044 Pulley Alignment Tool
PISTON
Used to check alignment of upper and lower pulley in piston aircraft.
![Page 21: Piston & Turbine Illustrated Tool Catalog](https://reader031.fdocuments.in/reader031/viewer/2022020705/61fb95222e268c58cd5fe41a/html5/thumbnails/21.jpg)
20
T-0045 Dog Leg Puller
PISTON & TURBINE
Used to remove dog leg from control rod.
![Page 22: Piston & Turbine Illustrated Tool Catalog](https://reader031.fdocuments.in/reader031/viewer/2022020705/61fb95222e268c58cd5fe41a/html5/thumbnails/22.jpg)
21
T-0048
Main Rotor Mast Nut Tool
PISTON & TURBINE Used to torque and remove the upper mast nut on all Enstrom Aircraft.
480B hub shown in picture.
![Page 23: Piston & Turbine Illustrated Tool Catalog](https://reader031.fdocuments.in/reader031/viewer/2022020705/61fb95222e268c58cd5fe41a/html5/thumbnails/23.jpg)
22
T-0051 Flapping Nut Tool
PISTON & TURBINE
Used to torque flapping pin nut.
T-0051A Alternate Tool
![Page 24: Piston & Turbine Illustrated Tool Catalog](https://reader031.fdocuments.in/reader031/viewer/2022020705/61fb95222e268c58cd5fe41a/html5/thumbnails/24.jpg)
23
T-0054 Dog Leg Alignment Tool
PISTON & TURBINE
Used to align dog legs when installing on control rods
When assembling the dog legs, check to see that they are in
alignment with the walking beam on top of the hub.
This tool is used at the factory to assemble the three dog legs at the same time.
![Page 25: Piston & Turbine Illustrated Tool Catalog](https://reader031.fdocuments.in/reader031/viewer/2022020705/61fb95222e268c58cd5fe41a/html5/thumbnails/25.jpg)
24
T-0056
Tail Rotor Spindle Bearing Retention Nut Wrench PISTON & TURBINE, (wide chord blades)
Used to torque bearing retention nuts on wide chord tail rotor spindles. Also used to torque tail rotor gearbox input shaft nut.
![Page 26: Piston & Turbine Illustrated Tool Catalog](https://reader031.fdocuments.in/reader031/viewer/2022020705/61fb95222e268c58cd5fe41a/html5/thumbnails/26.jpg)
25
T-0057 Damper Cycling Tool
PISTON & TURBINE
Used to bleed air from dampers following overhaul.
For older ‘A’ models that have not had the dampers modified, the dampers must be removed and installed in the tool to bleed. This is a picture of a pneumatic powered damper cycling tool at New Garden. It allows rate checking dampers as a troubleshooting aid.
![Page 27: Piston & Turbine Illustrated Tool Catalog](https://reader031.fdocuments.in/reader031/viewer/2022020705/61fb95222e268c58cd5fe41a/html5/thumbnails/27.jpg)
26
T-0078
Engine Adapter Installation Tool
Used to install the oil filler tube attachment adapter in the Lycoming Engine
![Page 28: Piston & Turbine Illustrated Tool Catalog](https://reader031.fdocuments.in/reader031/viewer/2022020705/61fb95222e268c58cd5fe41a/html5/thumbnails/28.jpg)
27
T-0079 Dog Leg Bearing Swaging Tools
PISTON & TURBINE
Used to install and tighten dog leg bearings, and single piece tail rotor pitchlink bearings
Step 1: Using the removal tool, cut the rolled edge from the bearing.
Step 2: Using a suitable tool, push the bearing out of the dog leg or the pitch link.
Step 3: Swage the first side of the bearing
Step 4: Swage the second side of the bearing.
![Page 29: Piston & Turbine Illustrated Tool Catalog](https://reader031.fdocuments.in/reader031/viewer/2022020705/61fb95222e268c58cd5fe41a/html5/thumbnails/29.jpg)
28
T-0086 Upper Guide Tube Retaining Nut Wrench
PISTON & TURBINE
Used to remove and install nuts that secure the upper swashplate slider shafts into the upper swashplate housing.
![Page 30: Piston & Turbine Illustrated Tool Catalog](https://reader031.fdocuments.in/reader031/viewer/2022020705/61fb95222e268c58cd5fe41a/html5/thumbnails/30.jpg)
29
T-0087-15 Tail Rotor Balance Mandrel
PISTON & TURBINE
Used to static balance the tail rotor assembly.
Dedicated balance stand Improvised balance stand
![Page 31: Piston & Turbine Illustrated Tool Catalog](https://reader031.fdocuments.in/reader031/viewer/2022020705/61fb95222e268c58cd5fe41a/html5/thumbnails/31.jpg)
30
T-0088 Tail Rotor Drive Shaft Alignment Tool
PISTON & TURBINE
Used to align tail rotor drive shaft. The shaft on the turbine is slightly larger diameter but it should work.
Use a caliper to measure the distance between the wire and the fuselage in the absence of the block
![Page 32: Piston & Turbine Illustrated Tool Catalog](https://reader031.fdocuments.in/reader031/viewer/2022020705/61fb95222e268c58cd5fe41a/html5/thumbnails/32.jpg)
31
T-0092 Taper Pin Removal Tool
PISTON & TURBINE
Used to remove taper pins from TR drive shaft with out damaging them.
![Page 33: Piston & Turbine Illustrated Tool Catalog](https://reader031.fdocuments.in/reader031/viewer/2022020705/61fb95222e268c58cd5fe41a/html5/thumbnails/33.jpg)
32
T-0100-1 Swashplate Bushing Installation Tool
PISTON & TURBINE
Used to align and press in swashplate axis bushings
Early style T-0100 tool has shorter and larger diameter head. It cannot be used on the late
style swashplates unless the head is turned down to clear the cut-out in the swashplate housing.
![Page 34: Piston & Turbine Illustrated Tool Catalog](https://reader031.fdocuments.in/reader031/viewer/2022020705/61fb95222e268c58cd5fe41a/html5/thumbnails/34.jpg)
33
T-0102-1 Upper Swashplate Guide Tube Press Tools
PISTON & TURBINE
Used to push the guide tube assembly from the upper swashplate bell housing.
Page 27
To press the guide tube assembly from the bell housing, equal force must be exerted on all three guide tubes at the same time.
Otherwise the rivets holding the guide tubes into their holder will shear.
![Page 35: Piston & Turbine Illustrated Tool Catalog](https://reader031.fdocuments.in/reader031/viewer/2022020705/61fb95222e268c58cd5fe41a/html5/thumbnails/35.jpg)
34
T-0104-1
Swashplate DU Bushing Installation Tool PISTON & TURBINE
Used to install the 28-16226 and 08-DU-08 sleeve
assembly.
The bushings can be installed using the T-0100 tool if the 28-16226 bushing is held in the far side of the swashplate to help align the driver so the
bushing goes in straight.
Use this bushing as an alignment aid when using the T-0100.
![Page 36: Piston & Turbine Illustrated Tool Catalog](https://reader031.fdocuments.in/reader031/viewer/2022020705/61fb95222e268c58cd5fe41a/html5/thumbnails/36.jpg)
35
T-0111 & T-0113 Correlator Rigging Tools
PISTON
Used to rig the correlator.
Dimensions and drawings for these tools can be found on page MM-13-104 & 5 of the maintenance manual.
T-
![Page 37: Piston & Turbine Illustrated Tool Catalog](https://reader031.fdocuments.in/reader031/viewer/2022020705/61fb95222e268c58cd5fe41a/html5/thumbnails/37.jpg)
36
0127 Magnetic Pickup Bracket
280FX
Used to hold Chadwick magnetic pick-up on 280FX models when tracking Main Rotor Blades.
![Page 38: Piston & Turbine Illustrated Tool Catalog](https://reader031.fdocuments.in/reader031/viewer/2022020705/61fb95222e268c58cd5fe41a/html5/thumbnails/38.jpg)
37
T-0133 Piston Pulley Restraining Tool
PISTON
![Page 39: Piston & Turbine Illustrated Tool Catalog](https://reader031.fdocuments.in/reader031/viewer/2022020705/61fb95222e268c58cd5fe41a/html5/thumbnails/39.jpg)
38
T-0134 Lower Swashplate Assembly Fixture
PISTON & TURBINE Used to hold lower swashplate while assembling and setting preload.
![Page 40: Piston & Turbine Illustrated Tool Catalog](https://reader031.fdocuments.in/reader031/viewer/2022020705/61fb95222e268c58cd5fe41a/html5/thumbnails/40.jpg)
39
T-135-1
Pinion Nut Wrench PISTON & TURBINE
Used to torque pinion nut on Piston & Turbine
![Page 41: Piston & Turbine Illustrated Tool Catalog](https://reader031.fdocuments.in/reader031/viewer/2022020705/61fb95222e268c58cd5fe41a/html5/thumbnails/41.jpg)
40
T-0053 Pinion Wrench
OBSOLETE
Used to torque pinion nut on old style installation.
![Page 42: Piston & Turbine Illustrated Tool Catalog](https://reader031.fdocuments.in/reader031/viewer/2022020705/61fb95222e268c58cd5fe41a/html5/thumbnails/42.jpg)
41
T-0136-1
Overrunning Clutch Wrench TURBINE
Used to remove and install overrunning clutch hardware.
![Page 43: Piston & Turbine Illustrated Tool Catalog](https://reader031.fdocuments.in/reader031/viewer/2022020705/61fb95222e268c58cd5fe41a/html5/thumbnails/43.jpg)
42
T-0137 Engine Hoist
TURBINE
![Page 44: Piston & Turbine Illustrated Tool Catalog](https://reader031.fdocuments.in/reader031/viewer/2022020705/61fb95222e268c58cd5fe41a/html5/thumbnails/44.jpg)
43
T-0139-1
Belt Tension Tool TURBINE
![Page 45: Piston & Turbine Illustrated Tool Catalog](https://reader031.fdocuments.in/reader031/viewer/2022020705/61fb95222e268c58cd5fe41a/html5/thumbnails/45.jpg)
44
T-0141 480 Pulley Alignment Tool
TURBINE
Used to align bottom belt pulley.
![Page 46: Piston & Turbine Illustrated Tool Catalog](https://reader031.fdocuments.in/reader031/viewer/2022020705/61fb95222e268c58cd5fe41a/html5/thumbnails/46.jpg)
45
T-0143
Tail Rotor Drive Shaft Alignment Tool TURBINE
Used to align the tail rotor driveshaft on 480 models.
.
(T-0088-same tool for the piston)
![Page 47: Piston & Turbine Illustrated Tool Catalog](https://reader031.fdocuments.in/reader031/viewer/2022020705/61fb95222e268c58cd5fe41a/html5/thumbnails/47.jpg)
46
T-0149-11 & 13
Grip Seal Installation Tool TURBINES
Used to install the grip end seal on the 480 grips with TT straps
1. Install the seal over the -11 tool taking care to be sure it is in the right direction T-0149-11 T-0149-13
2. Assemble the grip over the -11 tool. 3. Place the -13 tool over the part of the -11 that protrudes though the grip and using a hydraulic press, press the grip over the tool, seating the seal in the grip.
![Page 48: Piston & Turbine Illustrated Tool Catalog](https://reader031.fdocuments.in/reader031/viewer/2022020705/61fb95222e268c58cd5fe41a/html5/thumbnails/48.jpg)
47
T-0149-12
Grip to Spindle Installation Tool TURBINE
Used to assemble main rotor grip over the spindle on 480s with TT straps and the single 1720
style seal, used on 28-14318-3 spindles. Prevents damaging the seal.
1. Place the spindle over the -12 tool. 2. Slide the grip assembly over the tool and the spindle until the grip seats against the spindle. T-0149-12 Tool
![Page 49: Piston & Turbine Illustrated Tool Catalog](https://reader031.fdocuments.in/reader031/viewer/2022020705/61fb95222e268c58cd5fe41a/html5/thumbnails/49.jpg)
48
T-0152
Tail Rotor Balance Optical Sensor Fixture PISTON & TURBINE
Attaches to Tail Rotor Gear Box and holds Velocimeter and optical sensor for balancing tail rotor
assembly.
T-0153 Engine Fan Balance Tool
PISTON
Attaches to pylon aft of fan and holds optical sensor to balance engine fan assembly.
![Page 50: Piston & Turbine Illustrated Tool Catalog](https://reader031.fdocuments.in/reader031/viewer/2022020705/61fb95222e268c58cd5fe41a/html5/thumbnails/50.jpg)
49
T-0151-1 Main Rotor Flapping Bearing Installation Tool
Pistons and 480
Used for removing and installing main rotor flapping bearings.
T-0151-1 used for helicopters incorporating grease lubricated flapping bearings T-0162-1 used for helicopters incorporating oil lubricated flapping bearings
![Page 51: Piston & Turbine Illustrated Tool Catalog](https://reader031.fdocuments.in/reader031/viewer/2022020705/61fb95222e268c58cd5fe41a/html5/thumbnails/51.jpg)
50
T-0156 Oil Filler Tube Adapter Wrench
PISTON
Used for removing and installing engine oil filler tube adapter.
![Page 52: Piston & Turbine Illustrated Tool Catalog](https://reader031.fdocuments.in/reader031/viewer/2022020705/61fb95222e268c58cd5fe41a/html5/thumbnails/52.jpg)
51
T-0160-1 Damper Piston / Seal Tool
Tools used to Assemble the Piston Seals
![Page 53: Piston & Turbine Illustrated Tool Catalog](https://reader031.fdocuments.in/reader031/viewer/2022020705/61fb95222e268c58cd5fe41a/html5/thumbnails/53.jpg)
52
T-0161 U-Block Seal Installation Tool
![Page 54: Piston & Turbine Illustrated Tool Catalog](https://reader031.fdocuments.in/reader031/viewer/2022020705/61fb95222e268c58cd5fe41a/html5/thumbnails/54.jpg)
53
T-0162-1 Main Rotor Flapping Bearing Installation Tool
480B Used for removing and installing main rotor flapping bearings.
T-0151-1 used for helicopters incorporating grease lubricated flapping bearings T-0162-1 used for helicopters incorporating oil lubricated flapping bearings
![Page 55: Piston & Turbine Illustrated Tool Catalog](https://reader031.fdocuments.in/reader031/viewer/2022020705/61fb95222e268c58cd5fe41a/html5/thumbnails/55.jpg)
54
T-0164-1 Upper Pulley Wrench
TURBINE
Used to hold the upper pulley while torquing the pinion nut
To use tool to loosen the pinion nut disassemble it and reassemble the restraining blocks on the other side of the tool.
![Page 56: Piston & Turbine Illustrated Tool Catalog](https://reader031.fdocuments.in/reader031/viewer/2022020705/61fb95222e268c58cd5fe41a/html5/thumbnails/56.jpg)
55
T-0166-11
Oil Cooler Shaft Alignment Coupling TURBINE
Used to secure the oil cooler shaft to the lower pulley assembly while aligning the system.
![Page 57: Piston & Turbine Illustrated Tool Catalog](https://reader031.fdocuments.in/reader031/viewer/2022020705/61fb95222e268c58cd5fe41a/html5/thumbnails/57.jpg)
56
T-0168 Tail Rotor Assembly Fixture
PISTON AND TURBINE
This tool is use to hold the blade assembly in a vise
T-0169 Oleo Disassembly Tool PISTON AND TURBINE
This tool is use to disassembly the lower tube from the upper tube.
![Page 58: Piston & Turbine Illustrated Tool Catalog](https://reader031.fdocuments.in/reader031/viewer/2022020705/61fb95222e268c58cd5fe41a/html5/thumbnails/58.jpg)
57
T-0174 Main Rotor Hub Puller
PISTON & TURBINE
Bolts to MR hub and pulls it from the transmission mast
![Page 59: Piston & Turbine Illustrated Tool Catalog](https://reader031.fdocuments.in/reader031/viewer/2022020705/61fb95222e268c58cd5fe41a/html5/thumbnails/59.jpg)
58
T-1575 Swashplate Centering Tool
PISTON AND TURBINE Used to hold lower swashplate in centered position while rigging the controls.
![Page 60: Piston & Turbine Illustrated Tool Catalog](https://reader031.fdocuments.in/reader031/viewer/2022020705/61fb95222e268c58cd5fe41a/html5/thumbnails/60.jpg)
59
T-1656-3 Tool to Remove Blade Weights
Used to remove weights from blade pockets
![Page 61: Piston & Turbine Illustrated Tool Catalog](https://reader031.fdocuments.in/reader031/viewer/2022020705/61fb95222e268c58cd5fe41a/html5/thumbnails/61.jpg)
60
T-1709
UPPER SWASHPLATE BEARING TOOL PISTON & TURBINE
Usage: Remove or install upper swashplate bearing supporting housing.
To remove the bearing from the upper swashplate housing, heat the housing while it is sitting on spacers, and the bearing will drop out. This tool is not necessary for the operation.
![Page 62: Piston & Turbine Illustrated Tool Catalog](https://reader031.fdocuments.in/reader031/viewer/2022020705/61fb95222e268c58cd5fe41a/html5/thumbnails/62.jpg)
61
T-1758 Upper Swashplate Holding Fixture
PISTON & TURBINE
Universal blocks hold hat section in vise for removing upper swashplate guide tube nuts.
![Page 63: Piston & Turbine Illustrated Tool Catalog](https://reader031.fdocuments.in/reader031/viewer/2022020705/61fb95222e268c58cd5fe41a/html5/thumbnails/63.jpg)
62
T-1775 Cyclic Centering Rigging Tool
PISTON
Used to center and hold the cyclic sticks while rigging the control system in the piston aircraft
![Page 64: Piston & Turbine Illustrated Tool Catalog](https://reader031.fdocuments.in/reader031/viewer/2022020705/61fb95222e268c58cd5fe41a/html5/thumbnails/64.jpg)
63
T-2893 Tail Rotor Teeter Bearing Assembly Tool
PISTON & TURBINE
Used to remove teeter bearings on tail rotor assembly.
![Page 65: Piston & Turbine Illustrated Tool Catalog](https://reader031.fdocuments.in/reader031/viewer/2022020705/61fb95222e268c58cd5fe41a/html5/thumbnails/65.jpg)
64
T-2896-1 Main Rotor Damper Bleeding Tools
PISTON & TURBINE WITH HYDRAULIC STYLE DAMPERS
Used to bleed dampers. After installing, give a short stroke on one syringe and then a full stroke on the second. You will see a few air bubbles on each stroke. This method will prevent pushing the air that might be in the first reservoir into the damper cylinder.
![Page 66: Piston & Turbine Illustrated Tool Catalog](https://reader031.fdocuments.in/reader031/viewer/2022020705/61fb95222e268c58cd5fe41a/html5/thumbnails/66.jpg)
65
T-2889 Tail Rotor Rigging Tools
TURBINE
T-0012 used for ‘A’ models T-0080 used for ‘C’ & ‘F’ models T-2889 used for ‘480’ models
80’ Tool shown here
Neutral pedal position.
Full left pedal position
Full right pedal position
![Page 67: Piston & Turbine Illustrated Tool Catalog](https://reader031.fdocuments.in/reader031/viewer/2022020705/61fb95222e268c58cd5fe41a/html5/thumbnails/67.jpg)
66
NPN Main Rotor Blade Static Balance Tool
PISTON & TURBINE
Used to static balance the main rotor blaces.
1. Level knife edge support bracket, in both directions 2. Install heaviest blade on one side of unit. 3 Install a second blade on the fixture and balance until the unit reads level . 3. Install third blade and balance it to the first blade 4. Tool can be rented from New Garden Aviation Inc, 610-268-2048
![Page 68: Piston & Turbine Illustrated Tool Catalog](https://reader031.fdocuments.in/reader031/viewer/2022020705/61fb95222e268c58cd5fe41a/html5/thumbnails/68.jpg)
67
NPN Main Rotor Shaft TIR Measure Tool
PISTON & TURBINE Use to measure TIR on the main rotor shaft. Fabricate locally out of electrical conduit.
This unit was fabricated in Venezuela out of three pieces of conduit and three bolts with nuts.
![Page 69: Piston & Turbine Illustrated Tool Catalog](https://reader031.fdocuments.in/reader031/viewer/2022020705/61fb95222e268c58cd5fe41a/html5/thumbnails/69.jpg)
68
NPN Sprag Clutch Purge Tool
PISTON
Used to purge sprag clutch assembly during servicing.
Use a ¼-28 right-angle zerk fitting. Unscrew the end off, and discard the check ball and spring.
Turn the clutch so that one plug-bolt is at the 12 o’clock position and one is at either the 3 or 9 o’clock position. Remove the top, and one of the side plug-bolts, and install the modified zerk fitting in the top hole.
Using a sutable oil pump can or a sryinge, push a sufficient amount of turbine engine oil into the clutch until the oil that runs out of the side hole appears clean. Replace the plug-bolts in the clutch assembly.
![Page 70: Piston & Turbine Illustrated Tool Catalog](https://reader031.fdocuments.in/reader031/viewer/2022020705/61fb95222e268c58cd5fe41a/html5/thumbnails/70.jpg)
69
NPN Fan Shroud Alignment Tool
Used to hold the position of the fan shroud while it is installed around the engine.
This tool will hold the shroud in the proper position while the hardware is installed. The mechanic can reach through the holes in the tool to install the
inside hardware. It needs to be about 3/16 inch larger in diameter than the fan.
![Page 71: Piston & Turbine Illustrated Tool Catalog](https://reader031.fdocuments.in/reader031/viewer/2022020705/61fb95222e268c58cd5fe41a/html5/thumbnails/71.jpg)
70
NPN Magneto Spring Installation Tool
Piston
Used to insert springs in the magneto distributer block