piping connection

NORSOK STANDARD

COMMON REQUIREMENTS

PIPING DETAILS

L-CR-003 Rev. 1, January 1996

Please note that whilst every effort has been made to ensure the accuracy of the NORSOK standards neither OLF nor TBL or any of their members will assume liability for any use thereof.

Piping details


CONTENTS1 FOREWORD 2 SCOPE 3 NORMATIVE REFERENCES 4 DEFINITIONS AND ABBREVIATIONS 4.1 Definitions 4.2 Abbreviations 5 TECHNICAL REQUIREMENTS 5.1 General 5.2 Options 5.3 Double block 5.4 Modular compact valves 5.5 Valve legend 5.6 Drilling details 5.7 Hydraulic 5.8 Birdscreen ANNEX A TYPICAL DRAWINGS (NORMATIVE) 2 2 2 2 2 2 2 2 3 3 3 3 4 4 4 5

NORSOK standard

Page 1 of 6

Piping details


1

FOREWORD

NORSOK (The competitive standing of the Norwegian offshore sector) is the industry initiative to add value, reduce cost and lead time and remove unnecessary activities in offshore field developments and operations. The NORSOK standards are developed by the Norwegian petroleum industry as a part of the NORSOK initiative and are jointly issued by OLF (The Norwegian Oil Industry Association) and TBL (The Federation of Norwegian Engineering Industries). NORSOK standards are administered by NTS (Norwegian Technology Standards Institution). The purpose of this industry standard is to replace the individual oil company specifications for use in existing and future petroleum industry developments, subject to the individual company's review and application. The NORSOK standards make extensive references to international standards. Where relevant, the contents of this standard will be used to provide input to the international standardization process. Subject to implementation into international standards, this NORSOK standard will be withdrawn.

2

SCOPE

The standard defines the installation requirements for piping details.

3

NORMATIVE REFERENCESPiping and valves

NORSOK L-CR-001

4

DEFINITIONS AND ABBREVIATIONSShall mean normative in the application of NORSOK standards. Shall mean informative in the application of NORSOK standards. Shall is an absolute requirement which shall be followed strictly in order to conform with the standard. Should is a recommendation. Alternative solutions having the same functionality and quality are acceptable. May indicates a course of action that is permissible within the limits of the standard (a permission). Can-requirements are conditional and indicates a possibility open to the user of the standard.

4.1 Definitions Normative references Informative references Shall Should May Can

4.2 Abbreviations ASME American National Standards Institute

5

TECHNICAL REQUIREMENTS

5.1 General This document is based upon using components from L-CR-001. However, components not covered in L-CR-001 may be handled as special items. NORSOK standard Page 2 of 6

Piping details


5.2 Options This standard contains individual piping details. It is the intention that each project shall compile a set of standard sheets from this document applicable for the particular project. Undesired sheets and options (E.g. 10A or 10B) should be subtracted by the project. 5.3 Double block Requirements for double block (& bleed if applicable) shall be in accordance with P-CR-001. The details shown in this document have been based on the assumption of applying double block arrangement for ANSI Class 600 and above. 5.4 Modular compact valves The philosophy for use of modular compact valves will be included when these valves have been included in the next revision of NORSOK standard for Piping and valves, L-CR-001. However, some of the details in this standard show Modular Compact Valves. The extent of use of these valves, is to be decided by project. 5.5 Valve legend Please note that this standard are not using the NORSOK symbols according to Z-CR-004, CAD legend. The required symbols were not available when this standard was made.

Gate valve, normally open

Gate valve, normally closed

Globe valve, normally open

Globe valve, normally closed

Check valve

Ball valve, normally open

Hex head plug

NORSOK standard

Page 3 of 6

Piping details

L-CR-003 Rev. 1, January 1996 Threaded reducing flange with temporary hex head plug. Alternatively, blind flange tapped and bored with hex head plug.

5.6 Drilling details Drilling related piping is not included in this revision. 5.7 Hydraulic Hydraulic related piping is not included in this revision. 5.8 Birdscreen Use standard flanges for optional closure solutions during construction. For larger sizes, if no pressure testing is required, consider use of other closure solutions for weight reduction.

NORSOK standard

Page 4 of 6

Piping details Annex A


ANNEX ATitle

TYPICAL DRAWINGS (NORMATIVE)PD001 004 010A 010B 011A 011B 014 015 020 022 023 024 030 031 040 041 050A 050B 055 059 060 061 062 070 071

ANSI CLASS150 TO 2500 150 TO 2500 150 TO 300 150 TO 300 600 TO 2500 600 TO 2500 150 TO 300 600 TO 2500 150 TO 2500 150 TO 2500 150 TO 2500 150 TO 2500 150 150 150 TO 300 600 TO 2500 150 TO 2500 150 TO 2500 150 TO 2500 150 TO 2500 150 TO 2500 150 TO 2500 150 TO 2500 150 TO 2500 150 TO 2500

THERMOWELL CONNECTIONS EXTERNAL THERMOWELL CONNECTION INSTRUMENT PRESSURE CONNECTION (WELDED) INSTRUMENT PRESSURE CONNECTION (FLANGED) INSTRUMENT PRESSURE CONNECTION (WELDED, DB&B) INSTRUMENT PRESSURE CONNECTION (FLANGED, DB&B) INSTRUMENT PRESSURE CONNECTION TO VESSEL (WELDED) INSTRUMENT PRESSURE CONNECTION TO VESSEL (WELDED, DB&B) VESSEL TRIM LEVEL GAUGE VESSEL TRIM LEVEL TRANSMITTER (FLOAT TYPE) VESSEL TRIM LEVEL TRANSMITTER (D.P.) VESSEL TRIM LEVEL TRANSMITTER (D.P. INTRUSIVE TYPE) STILLING TUBE FOR ATM. TANK LEVEL TRANSM. (TOP ACCESS) ATMOSPHERIC TANK LEVEL LOGGING CONNECTING POINT ORIFICE FLANGE WITH FLAT AND RAISED FACE ORIFICE FLANGE WITH RTJ FLANGES LOCAL VENT & DRAIN (ALTERNATIVE 1) LOCAL VENT & DRAIN (ALTERNATIVE 2) HYDROSTATIC PRESSURE TESTING VENT & DRAIN BRACING DETAILS ANNUBAR CONNECTIONS ACCESS FITTING FOR SAND PROBE ACCESS FITTING FOR CORROSION MONITORING SAMPLE CONNECTION FOR PROCESS GAS/LIQUID SERV. (HAZ. FLUID) SAMPLE CONNECTION FOR UTILITY SERVICES (NON-HAZ. FLUID)

NORSOK standard

Page 5 of 6

Piping details Annex A


TEMPORARY "CONICAL" STRAINER TEMPORARY "BATH TUB" STRAINER DAVIT FOR BLIND FLANGE DRIP RING DETAILS RF FLANGES DRIP RING DETAILS RTJ FLANGES INLINE CONDENSATE DRAIN POINTS FOR STEAM MAINS END OF MAIN CONDENSATE DRAIN POINTS FOR STEAM MAINS TYPICAL UTILITY STATION CONCEPT

080 081 085 090 091 093 094 129

150 TO 2500 150 TO 2500 150 TO 2500 150 TO 300 600 TO 2500 150 TO 2500 150 TO 2500 150 TO 2500

NORSOK standard

Page 6 of 6

WITHDRAWAL SPACE 1.5" REINFORCED NIPOFLANGE (2 for CL 2500) INSTRUMENT PIPING 150 mm (165mm for CL 2500) 4" PIPE ECCENTRIC BW REDUCERS TO SUIT LINE SIZE: ie 4" x 1.5" + 1.5" x 1"

min

LINE SIZE 1"WITHDRAWAL SPACE 1.5" REINFORCED NIPOFLANGE (2" for CL 2500)

INSTRUMENT PIPING

4" PIPE ECCENTRIC BW REDUCER TO SUIT LINE SIZE

150mm (165mm for CL 2500)

min

LINE SIZE 1.5" TO 3"WITHDRAWAL SPACE 1.5" REINFORCED NIPOFLANGE (2" for CL 2500)

INSTRUMENT PIPING

150mm (165mm for CL 2500)

LINE SIZE >= 4"NOTES: 1. Rating and material grade of pipe and fittings shall be in accordance with the relevant piping class. 2. For installation in vertical lines use concentric buttweld reducers and 45 latroflange if required. 3. The Thermowell must be purchased to fit the inside diameter of the reinforced nipoflange which shall be machined according to the nominal inside diameter of the corresponding piping class. 4. Weldolet, nipple and flange to piping class may be used as an alternative to reinforced nipoflange where this can be documented to be more cost effective.

THERMOWELL CONNECTIONS CL 150 TO CL 2500

PD-001

Sht 1 of 1

Rev. 02

MINIMUM 250 MM FREE SPACE

TEMPORARY PLUG

1/2" NPT

100

NOTE 2 35 6.5 5 MM CONTINUOUS FILLET WELD TO BE WITHIN PIPING SCOPE OF WORK

INSTRUMENT PIPING

EXTERNAL THERMOWELL NOTE 1 FOR HORISONTAL AND VERTICAL PIPE

NOTES: 1. Material grade to be compatible with pipe & fittings. 2. Insulation thickness must be considered.

EXTERNAL THERMOWELL CONNECTION CL 150 TO CL 2500

PD-004

Sht 1 of 1

Rev. 02

TEMPORARY PLUG INSTRUMENT PIPING 3/4" GATE VALVE BW ONE END THREADED OTHER END

3/4" x 100 MM LONG NIPPLE, BBE FOR INSULATED LINES NOTE 3 BRANCH CONN. AS PER BRANCH SCHEDULE

HORIZONTAL LINES NOTE 4

45 MAXIMUM

45 MAXIMUM GAS LIQUID

ORIENTATION OF INSTRUMENT CONNECTION ON HEADER

NOTES: 1. 2. 3. 4. Rating and material of all items to be according to the relevant piping class. For bracing details, see PD-059. For vertical lines add elbow to achieve correct vertical orientation of instrument.

INSTRUMENT PRESSURE CONNECTION (WELDED) CL 150 TO CL 300

PD-010A Sht 1 of 1

Rev. 02

TEMPORARY PLUG INSTRUMENT PIPING 3/4" GATE VALVE FLANGED BOTH ENDS THR. RED. FLG 0.75 X 0.5 NPT (F)

3/4" FLANGE 3/4" x 100 MM LONG NIPPLE, BBE FOR INSULATED LINES NOTE 3 BRANCH CONN. AS PER BRANCH SCHEDULE


45 MAXIMUM



NOTES: 1. 2. 3. 4. Rating and material of all items to be according to the relevant piping class. For bracing details, see PD-059. For vertical lines add elbow to achieve correct vertical orientation of instrument.

INSTRUMENT PRESSURE CONNECTION (FLANGED) CL 150 TO CL 300

PD-010B Sht 1 of 1

Rev. 02

TEMPORARY PLUG INSTRUMENT PIPING 3/4" GLOBE VALVE BW ONE END THREADED OTHER END 3/4" GATE VALVE BW

3/4" x 100 MM LONG NIPPLE, BBE FOR INSULATED LINES NOTE 3 BRANCH CONN. AS PER BRANCH SCHEDULE


45 MAXIMUM



NOTES: 1. Rating and material of all items to be according to the relevant piping class. 2. 3. For bracing details, see PD-059. 4. For vertical lines add elbow to achieve correct vertical orientation of instrument.

INSTRUMENT PRESSURE CONNECTION (WELDED) CL 600 TO CL 2500

PD-011A Sht 1 of 1

Rev. 02

INSTRUMENT PIPING 3/4" GLOBE VALVE FLANGED

3/4" GATE VALVE FLANGED 3/4" FLANGE 3/4" x 100 MM LONG NIPPLE, BBE FOR INSULATED LINES NOTE 3 BRANCH CONN. AS PER BRANCH SCHEDULE


45 MAXIMUM



NOTES: 1. Rating and material of all items to be according to the relevant piping class. 2. 3. For bracing details, see PD-059. 4. For vertical lines add elbow to achieve correct vertical orientation of instrument.

INSTRUMENT PRESSURE CONNECTION (FLANGED) CL 600 TO CL 2500

PD-011B Sht 1 of 1

Rev. 02

TEMPORARY PLUG

INSTRUMENT

3/4" GATE VALVE BW ONE EN THREADED OTHER END 2" x 3/4" CONC. REDUCER 2" FLANGE WN 2" VESSEL FLANGE

PIPING

VESSEL

NOTES: 1. Rating and material of all items to be according to the relevant piping class.

INSTRUMENT PRESSURE CONNECTION TO VESSEL (WELDED), CL 150 TO CL 300

PD-014

Sht 1 of 1

Rev. 02

TEMPORARY PLUG

INSTRUMENT

3/4" GLOBE VALVE BW ONE END THREADED OTHER END

3/4" GATE VALVE BW BOTH ENDS

PIPING

2" x 3/4" CONC. REDUCER 2" FLANGE WN 2" VESSEL FLANGE

VESSEL

NOTES: 1. Rating and material of all items to be according to the relevant piping class.

INSTRUMENT PRESSURE CONNECTION TO VESSEL (WELDED), CL 600 TO CL 2500

PD-015

Sht 1 of 1

Rev. 02

VESSEL/ BRIDLE NOTE 5

NOTE 6

PIPING 1/2" NPT HEX HEAD PLUG

3/4" NIPPLE BOE/TOE & 0.75" WN FLANGE (TYP.) NOTE 3

0.75" x 1/2" NPT RED. FLANGE 0.75" GATE VALVE

2" GATE VALVE (TYP.) 2" WN FLANGE (TYP.) 2" x 0.75" ECC. REDUCER (TYP.) (NOTE 2) 0.75" WN FLANGE (TYP.) PIPING NOTE 5

0.75" GATE VALVE 0.75" x 1/2" NPT RED. FLANGE 1/2" NPT HEX HEAD PLUG 0.75" NOTE 4

0.75" GATE VALVE WHEN DRAIN AND VENT SHALL BE PERMANENTLY CONNECTED SEE SEPARATE DETAIL TO THE RIGHT 0.75" PIPING TO DRAIN/VENT AS PER P&ID 0.75" WN FLANGE (TYP)

NOTES: 1. 2. 3. 4. 5. 6. Rating and material grade of pipe and fittings shall be in accordance with the relevant piping class. Use ecc. reducers field welded to allow for alignment. Nipples to be seal welded by level gauge vendor for HC services only. Provide break flanges down stream first isolation valve when piped to drain/flare. Use double block for ANSI class 600 and above. Split between piping and instrument to be decided by project.

VESSEL TRIM LEVEL GAUGE CL 150 TO CL 2500

PD-020

Sht 1 of 1

Rev. 02

1/2" NPT HEX HEAD PLUG 0.75" x 1/2" NPT RED. FLANGE PIPING 0.75" 0.75" GATE VALVE

VESSEL

PIPING

INST.

2" GATE VALVE (TYP.)

NOTE 3

NOTE 3

INST.PIPING 0.75" GATE VALVE 0.75" x 1/2" NPT RED. FLANGE 1/2" NPT HEX HEAD PLUG

0.75"

0.75" NOTE 4

0.75" GATE VALVE 0.75" WN FLANGE (TYP) WHEN DRAIN AND VENT SHALL BE PERMANENTLY CONNECTED SEE SEPARATE DETAIL TO RIGHT

0.75" PIPING TO DRAIN/VENT AS PER P&ID

NOTES: 1. 2. 3. 4. Rating and material grade of pipe and fittings shall be in accordance with the relevant piping class. Introduce 2" flanges, elbow and pipe to reduce overall standout and provide for adjustment if necessary. Use double block for ANSI class 600 and above. Provide break flanges down stream first isolation valve when piped to drain/flare.

VESSEL TRIM LEVEL TRANSMITTER (FLOAT TYPE), CL 150 TO CL 2500

PD-022

Sht 1 of 1

Rev. 02

Flanged pressure sensing INSTRUMENT PIPING 2" Double block bleed valve PIPING VESSEL NOTE 5 Drip

2" Double block bleed valve Drip

DP cell

3/4" EQUAL TEE & 3/4" x SWAGE NIPPLE 3/4" GATE VALVE BW VESSEL PIPING NOTE 3 & 4 INSTRUMENT

NOTES: 1. 2. 3. 4. 5. 6. Rating and material grade of pipe and fittings shall be in accordance with the relevant piping class. Introduce 2" flanges, elbow and pipe to reduce overall standout and provide for adjustment if necessary. Check P&ID for any hard pipe requirements to closed drain/flare. Provide break flanges downstream first isolation valve when piped to drain. Location on vessel to be advices by instrument. Support (if required) to be designed by support group.

VESSEL TRIM LEVEL TRANSMITTER (D.P.), CL 150 TO CL 2500

PD-023

Sht 1 of 1

Rev. 02

F la n g e d p re s s u r e s e n s in g IN S T R U M E N T P IP IN G 2 " D o u b le b lo c k & b le e d v a lv e a s s e m b ly P IP IN G V E S S E L NO TE 5 D rip r in g

2 " D o u b le b lo c k & b le e d v a lv e D rip r in g D P c e ll

L in e s lo p e d 1 0 to w a r d s v e s s e l N o te 5 3/4" EQ UAL TEE & 3/4" x 1/2" SW AG E N IP P L E (B O E / T O E ) 3/4" G ATE VALVE BW VESSEL P IP IN G NO TE 3 & 4 IN S T R U M E N T

NOTES: 1. 2. 3. 4. 5. 6. Rating and material grade of pipe and fittings shall be in accordance with the relevant piping class. Introduce 2" flanges, elbow and pipe to reduce overall standout and provide for adjustment if necessary. Check P&ID for any hard pipe requirements to closed drain/flare. Provide break flanges downstream first isolation valve when piped to drain. Location on vessel to be advices by instrument. Support (if required) to be designed by support group.

VESSEL TRIM LEVEL TRANSMITTER (D.P. INTRUSIVE TYPE), CL 150 TO CL 2500

PD-024

Sht 1 of 1

Rev. 02

INSTRUMENT 3"or 4 WN FLANGE TANK TOP PIPING 3" or 4 x 6" CONC. REDUCER

APPROX. 100

APPROX. 100 x 20 MM SLOTS IN 6" 6"OR 4 PIPE

150

WELD TO TANK BOTTOM TANK BOTTOM

OPEN PIPE

NOTES: 1. 2. Rating and material grade of pipe and fittings shall be in accordance with the relevant piping class. Hole in blind flange for sensing unit to be drilled and tapped by instrument.

STILLING TUBE FOR ATMOSPHERIC TANK LEVEL TRANSMITTER (TOP ACCESS), CL150

PD-030

Sht 1 of 1

Rev. 02

SPECIAL FULL BORE BALL VALVE automatic closing, foot operated to be used for manual level logging

INSTRUMENT PIPING 2" NOZZLE NOTE 2 & 3 500

APPROX. 100 NOTE 4

STILLING WELLTO BE SUPPORTED IF NECESSARY

APPROX. 100 x 10 MM SLOTS IN 2 PIPE

50

OPEN PIPE

NOTES: 1. Rating and material grade of pipe and fittings shall be in accordance with the relevant piping class. 2. Nozzle to be provided with a stilling well of equal I.D. over the full height of tank. 3. Bolts, nuts & gaskets by piping. 4. Slot to be located as close to tank top as possible.

ATMOSPHERIC TANK MANUAL LEVEL LOGGING CONNECTING POINT, CL 150

PD-031

Sht 1 of 1

Rev. 02

45 MAX (TYP)

45 MAX (TYP)

ORIENTATION OF TAPS GAS AND VAPOUR INSTRUMENT PIPING

NOTE 2

ORIENTATION OF TAPS LIQUID

PIPING 1/2" RF 1/2" NIPPLE BOE/TOE 100 MM LONG NOTE 4. SEAL WELDS TYP. INTERNAL WELD BEADS TO GROUND FLUSH WITH PIPE WALL FLOW

INSTRUMENT TAG TO BE READ UPSTREAM

ANSI B16.36 CLASS ORIFICE BORED TO MATCH NOM. INTERNAL DIA OF CONNECTING

PIPING

1/2" GATE VALVE ONE END RF FLANGE OTHER END NPT-F WITH TEMPORARY HEX HEAD

INSTRUMENT

NOTES: 1. 2. 3. 4. Rating and material grade of nipples and valves to be the same as for the flow elements and relevant piping class. If double tapping is required, taps must be offset or extended to avoid clash of tap flanges and valves. For vertical lines add 45 elbow and additional nipple between orifice flange and valve to achieve vertical orientation. Alternatively use nipoflange if feasable.

ORIFICE FLANGE WITH FLAT AND RAISED FACE CL 150 TO CL 300

PD-040

Sht 1 of 1

Rev. 02

45 MAX (TYP)

45 MAX (TYP)

ORIENTATION OF TAPS FOR GAS AND VAPOUR SERVICE

NOTE 2

ORIENTATION OF TAPS FOR LIQUID SERVICE

FULL PENETRATION WELD

INTERNAL WELD BEADS TO BE GROUND FLUSH WITH PIPE WALL

FLOW

ANSI B16.5 RTJ WN FLANGES BORED TO MATCH NOM ID OF CONNECTING PIPE 1/2" GATE VALVE BW PIPING PIPING 1/2" GLOBE VALVE ONE END BW OTHER END NPT-F WITH TEMPORARY HEX HEAD PLUG

INSTRUMENT

NOTES: 1. 2. 3. Rating and material grade of nipples and valves to be the same as for the flow elements and relevant piping class. If double tapping is required, taps must be offset or extended to avoid clash of tap flanges and valves. For vertical lines add 45 elbow and additional nipple between orifice flange and valve to achieve vertical orientation.

ORIFICE FLANGE WITH RTJ FLANGES CL 600 TO CL 2500

PD-041

Sht 1 of 1

Rev. 02

B L IN D F L A N G E G A T E V A LV E FLG D

B L IN D F L A N G E G A T E V A LV E FLG D

W N FLA N G E

R E IN F O R C E D P IP E (B B E ) 1 0 0 M M L O N G NOTE 3 N IP O F L A N G E NOTE 4

NOTE 4

E Q /R E D . T E E A S P E R B R A N C H S P E C IF IC A T IO N H E A D E R S IZ E S 0 .5 " - 1 " H E A D E R S IZ E S 1 .5 " A N D A B O V E

B L IN D F L A N G E G LO BE V A LV E FLG D

B L IN D F L A N G E G LO BE V A LV E FLG D

G A T E V A LV E FLG D

G A T E V A LV E FLG D

W N FLA N G E

R E IN F O R C E D P IP E (B B E ) 1 0 0 M M L O N G NOTE 3 N IP O F L A N G E NOTE 4

NOTE 4

E Q /R E D . T E E A S P E R B R A N C H S P E C IF IC A T IO N H E A D E R S IZ E S 0 .5 " - 1 " H E A D E R S IZ E S 1 .5 " A N D A B O V E

VENTS & DRAINS FOR LINE SIZE 3/4" TO 12" TO BE 3/4" SIZE VENTS & DRAINS FOR LINE SIZE ABOVE 12" TO BE 1" SIZE NOTES: 1. 2. 3. 4. 5. Rating and material grade of pipe and fittings shall be in accordance with the relevant piping class. Cut to suit. For bracing see PD-059. When clearance between face of valve/top of deck or ceiling is less than 200mm, use PD-050B.

LOCAL VENT & DRAIN (ALTERNATIVE 1) CL 150 TO CL 2500

PD-050A

Sht 1 of 1

Rev. 02

BLIND FLANGE BLIND FLANGE GATE VALVE FLGD WN FLANGE 90 ELBOW GATE VALVE FLGD 90 ELBOW WN FLANGE

REINFORCED PIPE (BBE) 100 MM LONG NOTE 3 NIPOFLANGE NOTE 4

NOTE 4

EQ/RED TEE AS PER BRANCH SPECIFICATION HEADER SIZES 0.5" - 1" HEADER SIZES 1.5" AND ABOVE

BLIND FLANGE GLOBE VALVE FLGD BLIND FLANGE GATE VALVE FLGD 90 ELBOW WN FLANGE 90 ELBOW GATE VALVE FLGD

WN FLANGE NOTE 4 GLOBE VALVE FLGD PIPE (BBE) 100 MM LONG NOTE 3 NOTE 4 REINFORCED NIPOFLANGE

EQ/RED TEE AS PER BRANCH SPECIFICATION HEADER SIZES 0.5" - 1" HEADER SIZES 1.5" AND ABOVE

VENTS & DRAINS FOR LINE SIZE 3/4" TO 12" TO BE 3/4" SIZE VENTS & DRAINS FOR LINE SIZE ABOVE 12" TO BE 1" SIZE NOTES: 1. 2. 3. 4. Rating and material grade of pipe and fittings shall be in accordance with the relevant piping class. Cut to suit. For bracing see PD-059.

LOCAL VENT & DRAIN (ALTERNATIVE 2) CL 150 TO CL 2500

PD-050B Sht 1 of 1

Rev. 02

BLIND FLANGE WN FLANGE 100 MM LONG NIPPLE, BBE FOR INSULATED LINES NOTE 2. BRANCH CONN. AS PER BRANCH SCHEDULE

Vents and drains on lines 3/4" to 12" to be 3/4" size. Vents and drains on lines above 12" to be 1" size.

NOTES: 1. 2. Rating and material of all items to be according to the relevant piping class. For bracing details, see PD-059.

HYDROSTATIC PRESSURE TESTING VENT & DRAIN, CL 150 TO CL 2500

PD-055

Sht 1 of 1

Rev. 02

MIN MAX 50 100

MIN 50

MIN 50

A A

PAD NOTE 2&4 25x25x4 MM ANGLE IRON

MIN 50

PAD NOTE 2&4 25x25x4 MM ANGLE IRON NOTE 3

HEADER SIZE 2" AND ABOVE MIN MAX 100 MIN

Pipe or pad

PAD NOTE 2&4 25x25x4 MM

ANGLE IRON TO BE CUT IN BOTH ENDS

ON PIPE, FLANGE OR VALVE BODY NOTE 4. ANGLE IRON DRILLED AND CUT TO SUIT FIXING AT BACK OF FLANGE

VALVE BODY

FLANGE PAIR

NOTES: 1. 2. 3. 4. 5. All material grades to be compatible with pipe and fittings. Pad cut to suit shall be used on SCH 10S headers. Headers 12" and above shall have additional bracing in lateral direction. As an alternative to welding, screwed clamps which fully surround the pipe can be used, as well as screwed or clamped solutions directly onto valve body or flange if feasible. Vents and drains

piping connection

Documents

Transcript of piping connection