PIPE DETAILS - Support SealEco
30
Sept 2012 | 7:1 SealEco Post Address: P.O. Box 514, SE-331 25 Värnamo, Sweden Phone: +46 (0) 370 510 100, Fax: +46 (0) 370 510 101, Email: [email protected], www.sealeco.com Table of Construction Drawings PRE-001 Coping detail for a warm roof with a paver ballast -1 option PRE-002 Coping detail for an inverted roof with a gravel ballast - 1 option PRE-003 Coping detail for an inverted roof with a paver ballast - 1 option PRE-004 Coping detail for a cold roof with a timber deck- 1 option PRE-005 Coping detail for a cold roof with a gravel ballast - 1 option PRE-006 Coping detail for a cold roof with a paver ballast - 1 option PRE-007 Coping detail for a warm roof with a gravel ballast - 1 option PRE-008 Coping detail for a warm roof with a paver ballast - 2 option PRE-009 Coping detail for an inverted roof with a gravel ballast - 2 option PRE-010 Coping detail for an inverted roof with a paver ballast - 2 option PRE-011 Coping detail for a cold roof with a timber deck- 2 option PRE-012 Coping detail for a cold roof with a gravel ballast - 2 option PRE-013 Coping detail for a cold roof with a paver ballast - 2 option PRE-014 Coping detail for a warm roof with a gravel ballast - 2 option PRE-015 Coping detail for a cold roof with a timber deck- 3 option PRE-016 Coping detail for a cold roof with a gravel ballast - 3 option PRE-017 Coping detail for a warm roof with a gravel ballast - 3 option COPING DETAILS PRE-201 Pipe detail for a warm roof with a paver ballast PRE-202 Pipe detail for an inverted roof with a gravel ballast PRE-203 Pipe detail for an inverted roof with a paver ballast PRE-204 Pipe detail for a cold roof with a timber deck PRE-205 Pipe detail for a cold roof with a gravel ballast PRE-206 Pipe detail for a cold roof with a paver ballast PRE-207 Pipe detail for a warm roof with a gravel ballast PIPE DETAILS
Transcript of PIPE DETAILS - Support SealEco
Sept 2012 | 7:1
SealEcoPost Address: P.O. Box 514, SE-331 25 Värnamo, Sweden
Phone: +46 (0) 370 510 100, Fax: +46 (0) 370 510 101, Email: [email protected], www.sealeco.com
Table of Construction Drawings
PRE-001 Coping detail for a warm roof with a paver ballast -1 option
PRE-002 Coping detail for an inverted roof with a gravel ballast - 1 option
PRE-003 Coping detail for an inverted roof with a paver ballast - 1 option
PRE-004 Coping detail for a cold roof with a timber deck- 1 option
PRE-005 Coping detail for a cold roof with a gravel ballast - 1 option
PRE-006 Coping detail for a cold roof with a paver ballast - 1 option
PRE-007 Coping detail for a warm roof with a gravel ballast - 1 option
PRE-008 Coping detail for a warm roof with a paver ballast - 2 option
PRE-009 Coping detail for an inverted roof with a gravel ballast - 2 option
PRE-010 Coping detail for an inverted roof with a paver ballast - 2 option
PRE-011 Coping detail for a cold roof with a timber deck- 2 option
PRE-012 Coping detail for a cold roof with a gravel ballast - 2 option
PRE-013 Coping detail for a cold roof with a paver ballast - 2 option
PRE-014 Coping detail for a warm roof with a gravel ballast - 2 option
PRE-015 Coping detail for a cold roof with a timber deck- 3 option
PRE-016 Coping detail for a cold roof with a gravel ballast - 3 option
PRE-017 Coping detail for a warm roof with a gravel ballast - 3 option
COPING DETAILS
PRE-201 Pipe detail for a warm roof with a paver ballast
PRE-202 Pipe detail for an inverted roof with a gravel ballast
PRE-203 Pipe detail for an inverted roof with a paver ballast
PRE-204 Pipe detail for a cold roof with a timber deck
PRE-205 Pipe detail for a cold roof with a gravel ballast
PRE-206 Pipe detail for a cold roof with a paver ballast
PRE-207 Pipe detail for a warm roof with a gravel ballast
PIPE DETAILS
SealEcoPost Address: P.O. Box 514, SE-331 25 Värnamo, Sweden
Phone: +46 (0) 370 510 100, Fax: +46 (0) 370 510 101, Email: [email protected], www.sealeco.com
PRE-401 Expansion joint for an inverted roof with a paver ballast Plywood or synthetic bridge
PRE-402 Expansion joint for an inverted roof with a gravel ballast Plywood or synthetic bridge
PRE-403 Expansion joint for a cold roof with a timber deck Plywood or synthetic bridge
PRE-404 Expansion joint for a cold roof with a gravel ballast Plywood or synthetic bridge
PRE-405 Expansion joint For an inverted roof with a paver ballast - metal bridge
PRE-406 Expansion joint for an inverted roof with a gravel ballast - metal bridge
PRE-407 Expansion joint For a cold roof with a timber deck - metal bridge
PRE-408 Expansion joint for a cold roof with a gravel ballast - metal bridge
PRE-501 Reglet counterflashing
PRE-502 Surface mounted counterflashing
PRE-503 Clad Wall panel system counterflashing
WALL FLASHING DETAILS
PRE-601 Multi - System Roof tie-in
MULTI SYSTEM ROOF TIE-IN DETAILS
PRE-301 Drain detail for a warm roof with a paver ballast
PRE-302 Drain detail for an inverted roof with a gravel ballast
PRE-303 Drain detail for a cold roof with a timber deck
PRE-304 Drain detail for a cold roof with a gravel ballast
PRE-305 Drain detail for a cold roof with a paver ballast
PRE-306 Drain detail for a warm roof with a gravel ballast
PRE-307 Overflow drain detail for an inverted roof with a paver ballast
PRE-308 Overflow drain detail for an inverted roof with a gravel ballast
PRE-309 Overflow drain detail for an inverted roof with a paver ballast
PRE-310 Overflow drain detail for a cold roof with a timber deck
PRE-311 Overflow drain detail for a cold roof with a gravel ballast
PRE-312 Overflow drain detail for a cold roof with a paver ballast
PRE-313 Overflow drain detail for a warm roof with a gravel ballast
DRAIN DETAILS
Table of Construction Drawings
EXPANSION JOINT DETAILS
7:2 | Sept 2012
SealEcoPost Address: P.O. Box 514, SE-331 25 Värnamo, Sweden
Phone: +46 (0) 370 510 100, Fax: +46 (0) 370 510 101, Email: [email protected], www.sealeco.com Sept 2012 | 7:3
PRE-001 Coping detail for a warm roof with a paver ballast -1 option
Deck
Approved insulation
Approved Adhesive
Metal coping
200m
m M
inim
um
Vapour Barrier
Prelasti Membrane
Approved Fastenerspaced @ 200mm O.C.
Butyl tape
Sand layer or paversupports
Prelasti Membrane
Pavers
PRE-002 Coping detail for an inverted roof with a gravel ballast - 1 option
COPING DETAILS
Approved insulation
Approved Adhesive
Prelasti Membrane
200m
m M
inim
um
Metal coping
Gravel
Prelasti Membrane
Approved Fastenerspaced @ 200mm O.C.
Separation layer
Deck, equal tofloated concrete
SCALE: N/A
15/08/2012
PRE-002
Coping detail for aninverted roof with a gravelballast - 1 option
SealEcoP.O. Box 514SE 331 25 Vä[email protected]
AS A SUPPLIER OFMATERIAL ONLY,SEALECO NOT ASSUMERESPONSIBILITY FORDESIGN, ENGINEERING,QUANTITIES ORDIMENSIONS. THESPECIFIER, ENGINEERAND/OR ROOFINGAPPLICATOR SHALLVERIFY ALL DIMENSIONSAND SIZES
SealEcoPost Address: P.O. Box 514, SE-331 25 Värnamo, Sweden
Phone: +46 (0) 370 510 100, Fax: +46 (0) 370 510 101, Email: [email protected], www.sealeco.com
PRE-003 Coping detail for an inverted roof with a paver ballast - 1 option
PRE-004 Coping detail for a cold roof with a timber deck- 1 option
COPING DETAILS
Metal coping
Approved insulation
Approved Adhesive
Separation layer
Prelasti Membrane
Prelasti Membrane
Approved Fastenerspaced @ 200mm O.C.
Pavers
200m
m M
inim
um
Sand layer or paversupports
Deck, equal tofloated concrete
SCALE: N/A
15/08/2012
PRE-003
Coping detail for aninverted roof with a paverballast - 1 option
SealEcoP.O. Box 514SE 331 25 Vä[email protected]
AS A SUPPLIER OFMATERIAL ONLY,SEALECO NOT ASSUMERESPONSIBILITY FORDESIGN, ENGINEERING,QUANTITIES ORDIMENSIONS. THESPECIFIER, ENGINEERAND/OR ROOFINGAPPLICATOR SHALLVERIFY ALL DIMENSIONSAND SIZES
Approved Adhesive
Metal coping
Protection layerPrelasti Membrane
Approved Adhesive
200m
m M
inim
um
Bonding 300-500 mm
Timber Deck
Timber runners
Prelasti Membrane
Approved Fastenerspaced @ 200mm O.C.
Deck, equal tofloated concrete
7:4 | Sept 2012
SealEcoPost Address: P.O. Box 514, SE-331 25 Värnamo, Sweden
Phone: +46 (0) 370 510 100, Fax: +46 (0) 370 510 101, Email: [email protected], www.sealeco.com Sept 2012 | 7:5
PRE-005 Coping detail for a cold roof with a gravel ballast - 1 option
PRE-006 Coping detail for a cold roof with a paver ballast - 1 option
COPING DETAILS
Prelasti Membrane
Prelasti Membrane
Approved Adhesive
Metal coping
200m
m M
inim
um
Prelasti Membrane
Approved Fastenerspaced @ 200mm O.C.
Protection layerPrelasti Membrane
Pavers
Sand layer or paversupports
Deck, equal tofloated concrete
SCALE: N/A
15/08/2012
PRE-006
Coping detail for a coldroof with a paver ballast -1 option
SealEcoP.O. Box 514SE 331 25 Vä[email protected]
AS A SUPPLIER OFMATERIAL ONLY,SEALECO NOT ASSUMERESPONSIBILITY FORDESIGN, ENGINEERING,QUANTITIES ORDIMENSIONS. THESPECIFIER, ENGINEERAND/OR ROOFINGAPPLICATOR SHALLVERIFY ALL DIMENSIONSAND SIZES
SealEcoPost Address: P.O. Box 514, SE-331 25 Värnamo, Sweden
Phone: +46 (0) 370 510 100, Fax: +46 (0) 370 510 101, Email: [email protected], www.sealeco.com
PRE-007 Coping detail for a warm roof with a gravel ballast - 1 option
PRE-008 Coping detail for a warm roof with a paver ballast - 2 option
COPING DETAILS
Deck
Approved Adhesive
Metal coping
Bonding 300-500 mm
Prelasti Membrane
Approved Adhesive
Vapour Barrier
Butyl tape
GravelProtection layer. Can be left outif gravel is river washed fraction16/32 without crushed stones
Approved insulation compatiblewith Contact Adhesive
200m
m M
inim
um
Prelasti Membrane
Approved Fastenerspaced @ 200mm O.C.
SCALE: N/A
15/08/2012
PRE-007
Coping detail for a warmroof with a gravel ballast -1 option
SealEcoP.O. Box 514SE 331 25 Vä[email protected]
AS A SUPPLIER OFMATERIAL ONLY,SEALECO NOT ASSUMERESPONSIBILITY FORDESIGN, ENGINEERING,QUANTITIES ORDIMENSIONS. THESPECIFIER, ENGINEERAND/OR ROOFINGAPPLICATOR SHALLVERIFY ALL DIMENSIONSAND SIZES
Deck
Vapour Barrier
Approved insulation
Prelasti Membrane
Hot air weld
Thermobondreinforced splice strip
Contact Adhesive
Metal coping
Butyl tape
200m
m M
inim
um
Approved Fastenerspaced @ 200mm O.C.
Pavers
Sand layer or paversupports
SCALE: N/A
15/06/2009
PRE-008
Coping detail for a warmroof with a paver ballast -2 option
SealEcoP.O. Box 514SE 331 25 Vä[email protected]
AS A SUPPLIER OFMATERIAL ONLY,SEALECO NOT ASSUMERESPONSIBILITY FORDESIGN, ENGINEERING,QUANTITIES ORDIMENSIONS. THESPECIFIER, ENGINEERAND/OR ROOFINGAPPLICATOR SHALLVERIFY ALL DIMENSIONSAND SIZES
7:6 | Sept 2012
SealEcoPost Address: P.O. Box 514, SE-331 25 Värnamo, Sweden
Phone: +46 (0) 370 510 100, Fax: +46 (0) 370 510 101, Email: [email protected], www.sealeco.com Sept 2012 | 7:7
PRE-009 Coping detail for an inverted roof with a gravel ballast - 2 option
PRE-010 Coping detail for an inverted roof with a paver ballast - 2 option
COPING DETAILS
Deck, equal tofloated concrete
Approved insulation
Prelasti Membrane
Hot air weld
Contact Adhesive
Metal coping
200m
m M
inim
um
Thermobondreinforced splice strip
Gravel
Approved Fastenerspaced @ 200mm O.C.
Separation layer
SCALE: N/A
15/06/2009
PRE-009
Coping detail for aninverted roof with a gravelballast - 2 option
SealEcoP.O. Box 514SE 331 25 Vä[email protected]
AS A SUPPLIER OFMATERIAL ONLY,SEALECO NOT ASSUMERESPONSIBILITY FORDESIGN, ENGINEERING,QUANTITIES ORDIMENSIONS. THESPECIFIER, ENGINEERAND/OR ROOFINGAPPLICATOR SHALLVERIFY ALL DIMENSIONSAND SIZES
Approved insulation
Prelasti Membrane
Hot air weld
Approved Adhesive
Metal coping
Separation layer
200m
m M
inim
um
Thermobondreinforced splice strip
Approved Fastenerspaced @ 200mm O.C.
Pavers
Sand layer orpaver supports
Deck, equal tofloated concrete
SCALE: N/A
15/06/2009
PRE-010
Coping detail for aninverted roof with a paverballast - 2 option
SealEcoP.O. Box 514SE 331 25 Vä[email protected]
AS A SUPPLIER OFMATERIAL ONLY,SEALECO NOT ASSUMERESPONSIBILITY FORDESIGN, ENGINEERING,QUANTITIES ORDIMENSIONS. THESPECIFIER, ENGINEERAND/OR ROOFINGAPPLICATOR SHALLVERIFY ALL DIMENSIONSAND SIZES
SealEcoPost Address: P.O. Box 514, SE-331 25 Värnamo, Sweden
Phone: +46 (0) 370 510 100, Fax: +46 (0) 370 510 101, Email: [email protected], www.sealeco.com
PRE-011 Coping detail for a cold roof with a timber deck- 2 option
PRE-012 Coping detail for a cold roof with a gravel ballast - 2 option
COPING DETAILS
Prelasti Membrane
Hot air weld
Approved Adhesive
Metal coping
Protection layer
200m
m M
inim
um
Approved Fastenerspaced @ 200mmO.C. with Seam Plateor termination bar
Timber Deck
Timber runners
Thermobondreinforced splice strip
Approved Fastenerspaced @ 200mm O.C.
Deck, equal tofloated concrete
SCALE: N/A
15/06/2009
PRE-011
Coping detail for a coldroof with a timber deck -2 option
SealEcoP.O. Box 514SE 331 25 Vä[email protected]
AS A SUPPLIER OFMATERIAL ONLY,SEALECO NOT ASSUMERESPONSIBILITY FORDESIGN, ENGINEERING,QUANTITIES ORDIMENSIONS. THESPECIFIER, ENGINEERAND/OR ROOFINGAPPLICATOR SHALLVERIFY ALL DIMENSIONSAND SIZES
Prelasti Membrane
Hot air weld
Approved Adhesive
Metal coping
Protection layer. Can be left outif gravel is river washed fraction16 /32 without crushed stones
200m
m M
inim
um
Approved Fastener spaced@ 200mm O.C. with SeamPlate or termination bar
Gravel
Thermobondreinforced splice strip
Approved Fastenerspaced @ 200mm O.C.
Deck, equal tofloated concrete
SCALE: N/A
15/06/2009
PRE-012
Coping detail for a coldroof with a gravel ballast -2 option
SealEcoP.O. Box 514SE 331 25 Vä[email protected]
AS A SUPPLIER OFMATERIAL ONLY,SEALECO NOT ASSUMERESPONSIBILITY FORDESIGN, ENGINEERING,QUANTITIES ORDIMENSIONS. THESPECIFIER, ENGINEERAND/OR ROOFINGAPPLICATOR SHALLVERIFY ALL DIMENSIONSAND SIZES
7:8 | Sept 2012
SealEcoPost Address: P.O. Box 514, SE-331 25 Värnamo, Sweden
Phone: +46 (0) 370 510 100, Fax: +46 (0) 370 510 101, Email: [email protected], www.sealeco.com Sept 2012 | 7:9
PRE-013 Coping detail for a cold roof with a paver ballast - 2 option
PRE-014 Coping detail for a warm roof with a gravel ballast - 2 option
COPING DETAILS
Prelasti Membrane
Hot air weld
Approved Adhesive
Metal coping
200m
m M
inim
um
Thermobondreinforced splice strip
Approved Fastenerspaced @ 200mm O.C.
Pavers
Sand layer orpaver supports
Deck, equal tofloated concrete
SCALE: N/A
2012/08/2012
PRE-013
Coping detail for a coldroof with a paver ballast -2 option
SealEcoP.O. Box 514SE 331 25 Vä[email protected]
AS A SUPPLIER OFMATERIAL ONLY,SEALECO NOT ASSUMERESPONSIBILITY FORDESIGN, ENGINEERING,QUANTITIES ORDIMENSIONS. THESPECIFIER, ENGINEERAND/OR ROOFINGAPPLICATOR SHALLVERIFY ALL DIMENSIONSAND SIZES
Deck
Approved insulation
Prelasti Membrane
Hot air weld
Approved Adhesive
Metal coping
200m
m M
inim
um
Vapour Barrier
Approved Fastener spaced@ 200mm O.C. with SeamPlate or termination bar
Butyl tape
Thermobondreinforced splice strip
Gravel
Protection layer. Can be left out ifgravel is river washed fraction16/32 without crushed stones
Approved Fastenerspaced @ 200mm O.C.
SCALE: N/A
15/08/2012
PRE-014
Coping detail for a warmroof with a gravel ballast -2 option
SealEcoP.O. Box 514SE 331 25 Vä[email protected]
AS A SUPPLIER OFMATERIAL ONLY,SEALECO NOT ASSUMERESPONSIBILITY FORDESIGN, ENGINEERING,QUANTITIES ORDIMENSIONS. THESPECIFIER, ENGINEERAND/OR ROOFINGAPPLICATOR SHALLVERIFY ALL DIMENSIONSAND SIZES
SealEcoPost Address: P.O. Box 514, SE-331 25 Värnamo, Sweden
Phone: +46 (0) 370 510 100, Fax: +46 (0) 370 510 101, Email: [email protected], www.sealeco.com
PRE-015 Coping detail for a cold roof with a timber deck- 3 option
PRE-016 Coping detail for a cold roof with a gravel ballast - 3 option
COPING DETAILS
200m
m M
inim
um
Prelasti Membrane
Approved Adhesive
Metal coping
Protection layer
Approved Fastener spaced@ 200mm O.C. with SeamPlate or termination bar
Timber Deck
Timber runners
Approved Fastenerspaced @ 200mm O.C.
Deck, equal tofloated concrete
Prelasti Membranewith fixing tab
SCALE: N/A
15/08/2012
PRE-015
Coping detail for a coldroof with a timber deck -3 option
SealEcoP.O. Box 514SE 331 25 Vä[email protected]
AS A SUPPLIER OFMATERIAL ONLY,SEALECO NOT ASSUMERESPONSIBILITY FORDESIGN, ENGINEERING,QUANTITIES ORDIMENSIONS. THESPECIFIER, ENGINEERAND/OR ROOFINGAPPLICATOR SHALLVERIFY ALL DIMENSIONSAND SIZES
Prelasti Membrane
Approved Adhesive
Metal coping
200m
m M
inim
um
Approved Fastenerspaced @ 200mm O.C.with Seam Plate ortermination bar
Gravel
Protection layer. Can be left outif gravel is river washed fraction16/32 without crushed stones
Approved Fastenerspaced @ 200mm O.C.
Deck, equal tofloated concrete
Prelasti Membrane withfixing tab
SCALE: N/A
15/08/2012
PRE-016
Coping detail for a coldroof with a gravel ballast -3 option
SealEcoP.O. Box 514SE 331 25 Vä[email protected]
AS A SUPPLIER OFMATERIAL ONLY,SEALECO NOT ASSUMERESPONSIBILITY FORDESIGN, ENGINEERING,QUANTITIES ORDIMENSIONS. THESPECIFIER, ENGINEERAND/OR ROOFINGAPPLICATOR SHALLVERIFY ALL DIMENSIONSAND SIZES
7:10 | Sept 2012
SealEcoPost Address: P.O. Box 514, SE-331 25 Värnamo, Sweden
Phone: +46 (0) 370 510 100, Fax: +46 (0) 370 510 101, Email: [email protected], www.sealeco.com Sept 2012 | 7:11
PRE-017 Coping detail for a warm roof with a gravel ballast - 3 option
COPING DETAILS
Deck
Approved insulation
Prelasti Membrane
Approved Adhesive
Metal coping
Approved Fastener spaced@ 200mm O.C. with SeamPlate or termination bar
200m
m M
inim
um
Vapour Barrier
Butyl tape
Gravel
Protection layer. Can be left out ifgravel is river washed fraction16/32 without crushed stones
Approved Fastenerspaced @ 200mm O.C.
Elastoseal Membranewith fixing tab
SCALE: N/A
15/08/2012
PRE-017
Coping detail for a warmroof with a gravel ballast -3 option
SealEcoP.O. Box 514SE 331 25 Vä[email protected]
AS A SUPPLIER OFMATERIAL ONLY,SEALECO NOT ASSUMERESPONSIBILITY FORDESIGN, ENGINEERING,QUANTITIES ORDIMENSIONS. THESPECIFIER, ENGINEERAND/OR ROOFINGAPPLICATOR SHALLVERIFY ALL DIMENSIONSAND SIZES
SealEcoPost Address: P.O. Box 514, SE-331 25 Värnamo, Sweden
Phone: +46 (0) 370 510 100, Fax: +46 (0) 370 510 101, Email: [email protected], www.sealeco.com
PRE-201 Pipe detail for a warm roof with a paver ballast
PRE-202 Pipe detail for an inverted roof with a gravel ballast
PIPE DETAILS
200m
m M
inim
um
Vapour Barrier
Butyl tape
Approved Insulation
Prelasti Membrane
Jubilee Pipe Clamp
Approved Sealant
Thermobond PipeBoot
Deck
Hot Air Weld
Separation layer
Pavers
Sand layer or paversupports
SCALE: N/A PRE-201
Pipe detail for a warm roofwith a paver ballast
15/08/2012
SealEcoP.O. Box 514SE 331 25 Vä[email protected]
AS A SUPPLIER OFMATERIAL ONLY,SEALECO NOT ASSUMERESPONSIBILITY FORDESIGN, ENGINEERING,QUANTITIES ORDIMENSIONS. THESPECIFIER, ENGINEERAND/OR ROOFINGAPPLICATOR SHALLVERIFY ALL DIMENSIONSAND SIZES
200m
m M
inim
um
Approved Insulation
Prelasti Membrane
Jubilee Pipe Clamp
Hot Air Weld
Separation layer
Deck, equal tofloated concrete
Approved Sealant
Thermobond PipeBoot
Gravel
SCALE: N/A PRE-202
Pipe detail for an invertedroof with a gravel ballast
15/08/2012
SealEcoP.O. Box 514SE 331 25 Vä[email protected]
AS A SUPPLIER OFMATERIAL ONLY,SEALECO NOT ASSUMERESPONSIBILITY FORDESIGN, ENGINEERING,QUANTITIES ORDIMENSIONS. THESPECIFIER, ENGINEERAND/OR ROOFINGAPPLICATOR SHALLVERIFY ALL DIMENSIONSAND SIZES
7:12 | Sept 2012
SealEcoPost Address: P.O. Box 514, SE-331 25 Värnamo, Sweden
Phone: +46 (0) 370 510 100, Fax: +46 (0) 370 510 101, Email: [email protected], www.sealeco.com Sept 2012 | 7:13
PRE-203 Pipe detail for an inverted roof with a paver ballast
PRE-204 Pipe detail for a cold roof with a timber deck
PIPE DETAILS
200m
m M
inim
um
Approved Insulation
Prelasti Membrane
Jubilee Pipe Clamp
Hot Air Weld
Deck, equal tofloated concrete
Approved Sealant
Thermobond PipeBoot
Separation layer
Pavers
Sand layer or paversupports
SCALE: N/A PRE-203
Pipe detail for an invertedroof with a paver ballast
15/08/2012
SealEcoP.O. Box 514SE 331 25 Vä[email protected]
AS A SUPPLIER OFMATERIAL ONLY,SEALECO NOT ASSUMERESPONSIBILITY FORDESIGN, ENGINEERING,QUANTITIES ORDIMENSIONS. THESPECIFIER, ENGINEERAND/OR ROOFINGAPPLICATOR SHALLVERIFY ALL DIMENSIONSAND SIZES
Prelasti Membrane
Hot Air Weld
Timber Deck
200m
m M
inim
um
Jubilee Pipe Clamp
Deck, equal tofloated concrete
Approved Sealant
Protection layer
Timber runners
Thermobond PipeBoot
SCALE: N/A PRE-204
Pipe detail for a cold roofwith a timber deck
15/08/2012
SealEcoP.O. Box 514SE 331 25 Vä[email protected]
AS A SUPPLIER OFMATERIAL ONLY,SEALECO NOT ASSUMERESPONSIBILITY FORDESIGN, ENGINEERING,QUANTITIES ORDIMENSIONS. THESPECIFIER, ENGINEERAND/OR ROOFINGAPPLICATOR SHALLVERIFY ALL DIMENSIONSAND SIZES
SealEcoPost Address: P.O. Box 514, SE-331 25 Värnamo, Sweden
Phone: +46 (0) 370 510 100, Fax: +46 (0) 370 510 101, Email: [email protected], www.sealeco.com
PRE-205 Pipe detail for a cold roof with a gravel ballast
PRE-206 Pipe detail for a cold roof with a paver ballast
PIPE DETAILS
Prelasti Membrane
Hot Air Weld
Jubilee Pipe Clamp
200m
m M
inim
um
Deck, equal tofloated concrete
Approved Sealant
Thermobond PipeBoot
Gravel
Protection layer. Can be left outif gravel is river washed fraction16/32 without crushed stones
SCALE: N/A PRE-205
Pipe detail for a cold roofwith a gravel ballast
15/08/2012
SealEcoP.O. Box 514SE 331 25 Vä[email protected]
AS A SUPPLIER OFMATERIAL ONLY,SEALECO NOT ASSUMERESPONSIBILITY FORDESIGN, ENGINEERING,QUANTITIES ORDIMENSIONS. THESPECIFIER, ENGINEERAND/OR ROOFINGAPPLICATOR SHALLVERIFY ALL DIMENSIONSAND SIZES
Prelasti Membrane
Jubilee Pipe Clamp
200m
m M
inim
um
Deck, equal tofloated concrete
Approved Sealant
Thermobond PipeBoot
Hot Air Weld
Separation layer
Pavers
Sand layer or paversupports
SCALE: N/A PRE-206
Pipe detail for a cold roofwith a paver ballast
15/06/2009
SealEcoP.O. Box 514SE 331 25 Vä[email protected]
AS A SUPPLIER OFMATERIAL ONLY,SEALECO NOT ASSUMERESPONSIBILITY FORDESIGN, ENGINEERING,QUANTITIES ORDIMENSIONS. THESPECIFIER, ENGINEERAND/OR ROOFINGAPPLICATOR SHALLVERIFY ALL DIMENSIONSAND SIZES
7:14 | Sept 2012
SealEcoPost Address: P.O. Box 514, SE-331 25 Värnamo, Sweden
Phone: +46 (0) 370 510 100, Fax: +46 (0) 370 510 101, Email: [email protected], www.sealeco.com Sept 2012 | 7:15
PRE-207 Pipe detail for a warm roof with a gravel ballast
PIPE DETAILS
Jubilee Pipe Clamp
200m
m M
inim
um
Vapour Barrier
Butyl tape
Approved Insulation
Deck
Prelasti Membrane
Hot Air Weld
Approved Sealant
Thermobond PipeBoot
Gravel
Protection layer. Can be left outif gravel is river washed fraction16/32 without crushed stones
SCALE: N/A PRE-207
Pipe detail for a warm roofwith a gravel ballast
15/08/2012
SealEcoP.O. Box 514SE 331 25 Vä[email protected]
AS A SUPPLIER OFMATERIAL ONLY,SEALECO NOT ASSUMERESPONSIBILITY FORDESIGN, ENGINEERING,QUANTITIES ORDIMENSIONS. THESPECIFIER, ENGINEERAND/OR ROOFINGAPPLICATOR SHALLVERIFY ALL DIMENSIONSAND SIZES
SealEcoPost Address: P.O. Box 514, SE-331 25 Värnamo, Sweden
Phone: +46 (0) 370 510 100, Fax: +46 (0) 370 510 101, Email: [email protected], www.sealeco.com
PRE-301 Drain detail for a warm roof with a paver ballast
PRE-302 Drain detail for an inverted roof with a gravel ballast
DRAIN DETAILS
Deck
Vapour Barrier
Approved Insulation
Butyl tape
Compression ringfactory applied
PC Drain with Thermobond collar
Drain Outlet
Prelasti Membrane
Gravel Grate
Approved fastener
Hot- Air Weld
Pavers
Separation layer
Sand layer or paver supports
SCALE: N/A PRE-301
Drain detail for a warmroof with a paver ballast
15/08/2012
SealEcoP.O. Box 514SE 331 25 Vä[email protected]
AS A SUPPLIER OFMATERIAL ONLY,SEALECO NOT ASSUMERESPONSIBILITY FORDESIGN, ENGINEERING,QUANTITIES ORDIMENSIONS. THESPECIFIER, ENGINEERAND/OR ROOFINGAPPLICATOR SHALLVERIFY ALL DIMENSIONSAND SIZES
Deck, equal to floatedconcrete
Drain Outlet
Prelasti Membrane
Gravel Grate
Approved fastener
Approved Insulation
Hot- Air Weld
Gravel
Protection/Separationlayer
Compression ringfactory applied
PC Drain withThermobond collar
SCALE: N/A PRE-302
Drain detail for aninverted roof with agravel ballast
15/08/2012
SealEcoP.O. Box 514SE 331 25 Vä[email protected]
AS A SUPPLIER OFMATERIAL ONLY,SEALECO NOT ASSUMERESPONSIBILITY FORDESIGN, ENGINEERING,QUANTITIES ORDIMENSIONS. THESPECIFIER, ENGINEERAND/OR ROOFINGAPPLICATOR SHALLVERIFY ALL DIMENSIONSAND SIZES
7:16 | Sept 2012
SealEcoPost Address: P.O. Box 514, SE-331 25 Värnamo, Sweden
Phone: +46 (0) 370 510 100, Fax: +46 (0) 370 510 101, Email: [email protected], www.sealeco.com Sept 2012 | 7:17
PRE-303 Drain detail for a cold roof with a timber deck
PRE-304 Drain detail for a cold roof with a gravel ballast
DRAIN DETAILS
Drain Outlet
Prelasti Membrane
Approved fastener
Hot- Air Weld
Protection layer
Timber Deck
Timber runners
Deck, equal tofloated concrete
Gravel Grate
Compression ringfactory applied
PC Drain withThermobond collar
SCALE: N/A Prelasti-303
Drain detail for a coldroof with a timber deck
15/08/2012
SealEcoP.O. Box 514SE 331 25 Vä[email protected]
AS A SUPPLIER OFMATERIAL ONLY,SEALECO NOT ASSUMERESPONSIBILITY FORDESIGN, ENGINEERING,QUANTITIES ORDIMENSIONS. THESPECIFIER, ENGINEERAND/OR ROOFINGAPPLICATOR SHALLVERIFY ALL DIMENSIONSAND SIZES
Drain Outlet
Prelasti Membrane
Approved fastener
Hot- Air Weld
Deck, equal tofloated concrete
Gravel
Protection/Separation layer
Gravel Grate
Compression ringfactory applied
PC Drain withThermobond collar
SCALE: N/A PRE-304
Drain detail for a coldroof with a gravel ballast
15/08/2012
SealEcoP.O. Box 514SE 331 25 Vä[email protected]
AS A SUPPLIER OFMATERIAL ONLY,SEALECO NOT ASSUMERESPONSIBILITY FORDESIGN, ENGINEERING,QUANTITIES ORDIMENSIONS. THESPECIFIER, ENGINEERAND/OR ROOFINGAPPLICATOR SHALLVERIFY ALL DIMENSIONSAND SIZES
SealEcoPost Address: P.O. Box 514, SE-331 25 Värnamo, Sweden
Phone: +46 (0) 370 510 100, Fax: +46 (0) 370 510 101, Email: [email protected], www.sealeco.com
PRE-305 Drain detail for a cold roof with a paver ballast
PRE-306 Drain detail for a warm roof with a gravel ballast
DRAIN DETAILS
Drain Outlet
Prelasti Membrane
Approved fastener
Hot- Air Weld
Deck, equal tofloated concrete
Gravel Grate
Compression ringfactory applied
PC Drain withThermobond collar
Pavers
Separation layer
Sand layer or paver supports
SCALE: N/A PRE-305
Drain detail for a coldroof with a paver ballast
15/08/2012
SealEcoP.O. Box 514SE 331 25 Vä[email protected]
AS A SUPPLIER OFMATERIAL ONLY,SEALECO NOT ASSUMERESPONSIBILITY FORDESIGN, ENGINEERING,QUANTITIES ORDIMENSIONS. THESPECIFIER, ENGINEERAND/OR ROOFINGAPPLICATOR SHALLVERIFY ALL DIMENSIONSAND SIZES
Vapour Barrier
Approved Insulation
Butyl tape
Drain Outlet
Prelasti Membrane
Approved fastener
Hot- Air Weld
Deck
Gravel
Protection/Separation layer
Gravel Grate
Compression ringfactory applied
PC Drain withThermobond collar
SCALE: N/A PRE-306
Drain detail for a warmroof with a gravel ballast
15/08/2012
SealEcoP.O. Box 514SE 331 25 Vä[email protected]
AS A SUPPLIER OFMATERIAL ONLY,SEALECO NOT ASSUMERESPONSIBILITY FORDESIGN, ENGINEERING,QUANTITIES ORDIMENSIONS. THESPECIFIER, ENGINEERAND/OR ROOFINGAPPLICATOR SHALLVERIFY ALL DIMENSIONSAND SIZES
7:18 | Sept 2012
SealEcoPost Address: P.O. Box 514, SE-331 25 Värnamo, Sweden
Phone: +46 (0) 370 510 100, Fax: +46 (0) 370 510 101, Email: [email protected], www.sealeco.com Sept 2012 | 7:19
PRE-307 Overflow drain detail for a warm roof with a paver ballast
PRE-308 Overflow drain detail for an inverted roof with a gravel ballast
DRAIN DETAILS
Deck
Hot - Air Weld
Approved Insulation
Hot - Air Weld
Prelasti Membrane
Approved Adhesive
Butyl tape
Prelasti Membrane
Vapour Barrier
Drain PE as overflow drain
Pavers
Sand layer orpaver supports
SCALE: N/A PRE-307
Overflow drain detail foran inverted roof with apaver ballast
15/07/2012
SealEcoP.O. Box 514SE 331 25 Vä[email protected]
AS A SUPPLIER OFMATERIAL ONLY,SEALECO NOT ASSUMERESPONSIBILITY FORDESIGN, ENGINEERING,QUANTITIES ORDIMENSIONS. THESPECIFIER, ENGINEERAND/OR ROOFINGAPPLICATOR SHALLVERIFY ALL DIMENSIONSAND SIZES
Deck, equal to floated concrete
Hot - Air Weld
Approved Adhesive
Prelasti Membrane
Hot - Air Weld
Drain PE as overflow drain
Gravel
Protection layer. Can be left outif gravel is river washedfraction 16/32 without crushedstones
Prelasti Membrane
SCALE: N/A PRE-308
Overflow drain detail fora warm roof with a gravelballast
15/08/2012
SealEcoP.O. Box 514SE 331 25 Vä[email protected]
AS A SUPPLIER OFMATERIAL ONLY,SEALECO NOT ASSUMERESPONSIBILITY FORDESIGN, ENGINEERING,QUANTITIES ORDIMENSIONS. THESPECIFIER, ENGINEERAND/OR ROOFINGAPPLICATOR SHALLVERIFY ALL DIMENSIONSAND SIZES
Deck
Hot - Air Weld
Approved Insulation
Hot - Air Weld
Prelasti Membrane
Approved Adhesive
Butyl tape
Prelasti Membrane
Vapour Barrier
Drain PE as overflow drain
Pavers
Sand layer orpaver supports
SCALE: N/A PRE-307
Overflow drain detail foran inverted roof with apaver ballast
15/07/2012
SealEcoP.O. Box 514SE 331 25 Vä[email protected]
AS A SUPPLIER OFMATERIAL ONLY,SEALECO NOT ASSUMERESPONSIBILITY FORDESIGN, ENGINEERING,QUANTITIES ORDIMENSIONS. THESPECIFIER, ENGINEERAND/OR ROOFINGAPPLICATOR SHALLVERIFY ALL DIMENSIONSAND SIZES
Deck, equal to floated concrete
Hot - Air Weld
Approved Adhesive
Prelasti Membrane
Hot - Air Weld
Drain PE as overflow drain
Gravel
Protection layer. Can be left outif gravel is river washedfraction 16/32 without crushedstones
Prelasti Membrane
SCALE: N/A PRE-308
Overflow drain detail fora warm roof with a gravelballast
15/08/2012
SealEcoP.O. Box 514SE 331 25 Vä[email protected]
AS A SUPPLIER OFMATERIAL ONLY,SEALECO NOT ASSUMERESPONSIBILITY FORDESIGN, ENGINEERING,QUANTITIES ORDIMENSIONS. THESPECIFIER, ENGINEERAND/OR ROOFINGAPPLICATOR SHALLVERIFY ALL DIMENSIONSAND SIZES
SealEcoPost Address: P.O. Box 514, SE-331 25 Värnamo, Sweden
Phone: +46 (0) 370 510 100, Fax: +46 (0) 370 510 101, Email: [email protected], www.sealeco.com
PRE-309 Overflow drain detail for an inverted roof with a paver ballast
PRE-310 Overflow drain detail for a cold roof with a timber deck
DRAIN DETAILS
Deck, equal to floated concrete
Hot - Air Weld
Approved Adhesive
Prelasti Membrane
Hot - Air Weld
Drain PE as overflow drain
Separation layer
Pavers
Sand layer
Prelasti Membrane
SCALE: N/A PRE-309
Overflow drain detail foran inverted roof with apaver ballast
15/08/2012
SealEcoP.O. Box 514SE 331 25 Vä[email protected]
AS A SUPPLIER OFMATERIAL ONLY,SEALECO NOT ASSUMERESPONSIBILITY FORDESIGN, ENGINEERING,QUANTITIES ORDIMENSIONS. THESPECIFIER, ENGINEERAND/OR ROOFINGAPPLICATOR SHALLVERIFY ALL DIMENSIONSAND SIZES
Hot - Air Weld
Hot - Air Weld
Approved Adhesive
Protection layerPrelasti Membrane
Approved Adhesive
Deck, equal to floated concrete
Timber Deck
Timber runners
Drain PE as overflow drain
Prelasti Membrane
SCALE: N/A PRE-310
Overflow drain detail fora cold roof with a timberdeck
15/08/2012
SealEcoP.O. Box 514SE 331 25 Vä[email protected]
AS A SUPPLIER OFMATERIAL ONLY,SEALECO NOT ASSUMERESPONSIBILITY FORDESIGN, ENGINEERING,QUANTITIES ORDIMENSIONS. THESPECIFIER, ENGINEERAND/OR ROOFINGAPPLICATOR SHALLVERIFY ALL DIMENSIONSAND SIZES
Deck, equal to floated concrete
Hot - Air Weld
Approved Adhesive
Prelasti Membrane
Hot - Air Weld
Drain PE as overflow drain
Separation layer
Pavers
Sand layer
Prelasti Membrane
SCALE: N/A PRE-309
Overflow drain detail foran inverted roof with apaver ballast
15/08/2012
SealEcoP.O. Box 514SE 331 25 Vä[email protected]
AS A SUPPLIER OFMATERIAL ONLY,SEALECO NOT ASSUMERESPONSIBILITY FORDESIGN, ENGINEERING,QUANTITIES ORDIMENSIONS. THESPECIFIER, ENGINEERAND/OR ROOFINGAPPLICATOR SHALLVERIFY ALL DIMENSIONSAND SIZES
Hot - Air Weld
Hot - Air Weld
Approved Adhesive
Protection layerPrelasti Membrane
Approved Adhesive
Deck, equal to floated concrete
Timber Deck
Timber runners
Drain PE as overflow drain
Prelasti Membrane
SCALE: N/A PRE-310
Overflow drain detail fora cold roof with a timberdeck
15/08/2012
SealEcoP.O. Box 514SE 331 25 Vä[email protected]
AS A SUPPLIER OFMATERIAL ONLY,SEALECO NOT ASSUMERESPONSIBILITY FORDESIGN, ENGINEERING,QUANTITIES ORDIMENSIONS. THESPECIFIER, ENGINEERAND/OR ROOFINGAPPLICATOR SHALLVERIFY ALL DIMENSIONSAND SIZES
7:20 | Sept 2012
SealEcoPost Address: P.O. Box 514, SE-331 25 Värnamo, Sweden
Phone: +46 (0) 370 510 100, Fax: +46 (0) 370 510 101, Email: [email protected], www.sealeco.com Sept 2012 | 7:21
PRE-311 Overflow drain detail for a cold roof with a gravel ballast
PRE-312 Overflow drain detail for a cold roof with a paver ballast
DRAIN DETAILS
Hot - Air Weld
Hot - Air Weld
Approved Adhesive
Prelasti Membrane
Approved Adhesive
Deck, equal tofloated concrete
Drain PE as overflow drain
GravelProtection layer. Can be left out ifgravel is river washed fraction 16/32without crushed stones
Prelasti Membrane
SCALE: N/A PRE-311
Overflow drain detail fora cold roof with a gravelballast
15/08/2015
SealEcoP.O. Box 514SE 331 25 Vä[email protected]
AS A SUPPLIER OFMATERIAL ONLY,SEALECO NOT ASSUMERESPONSIBILITY FORDESIGN, ENGINEERING,QUANTITIES ORDIMENSIONS. THESPECIFIER, ENGINEERAND/OR ROOFINGAPPLICATOR SHALLVERIFY ALL DIMENSIONSAND SIZES
Hot - Air Weld
Hot - Air Weld
Approved Adhesive
Prelasti Membrane
Deck, equal to floated concrete
Drain PE as overflow drain
Pavers
Sand layer or paver supports
Elastoseal Membrane
SCALE: N/A PRE-312
Overflow drain detail fora cold roof with a paverballast
15/08/2012
SealEcoP.O. Box 514SE 331 25 Vä[email protected]
AS A SUPPLIER OFMATERIAL ONLY,SEALECO NOT ASSUMERESPONSIBILITY FORDESIGN, ENGINEERING,QUANTITIES ORDIMENSIONS. THESPECIFIER, ENGINEERAND/OR ROOFINGAPPLICATOR SHALLVERIFY ALL DIMENSIONSAND SIZES
Hot - Air Weld
Hot - Air Weld
Approved Adhesive
Prelasti Membrane
Approved Adhesive
Deck, equal tofloated concrete
Drain PE as overflow drain
GravelProtection layer. Can be left out ifgravel is river washed fraction 16/32without crushed stones
Prelasti Membrane
SCALE: N/A PRE-311
Overflow drain detail fora cold roof with a gravelballast
15/08/2015
SealEcoP.O. Box 514SE 331 25 Vä[email protected]
AS A SUPPLIER OFMATERIAL ONLY,SEALECO NOT ASSUMERESPONSIBILITY FORDESIGN, ENGINEERING,QUANTITIES ORDIMENSIONS. THESPECIFIER, ENGINEERAND/OR ROOFINGAPPLICATOR SHALLVERIFY ALL DIMENSIONSAND SIZES
Hot - Air Weld
Hot - Air Weld
Approved Adhesive
Prelasti Membrane
Deck, equal to floated concrete
Drain PE as overflow drain
Pavers
Sand layer or paver supports
Elastoseal Membrane
SCALE: N/A PRE-312
Overflow drain detail fora cold roof with a paverballast
15/08/2012
SealEcoP.O. Box 514SE 331 25 Vä[email protected]
AS A SUPPLIER OFMATERIAL ONLY,SEALECO NOT ASSUMERESPONSIBILITY FORDESIGN, ENGINEERING,QUANTITIES ORDIMENSIONS. THESPECIFIER, ENGINEERAND/OR ROOFINGAPPLICATOR SHALLVERIFY ALL DIMENSIONSAND SIZES
SealEcoPost Address: P.O. Box 514, SE-331 25 Värnamo, Sweden
Phone: +46 (0) 370 510 100, Fax: +46 (0) 370 510 101, Email: [email protected], www.sealeco.com
PRE-313 Overflow drain detail for a warm roof with a gravel ballast
DRAIN DETAILS
Deck
Hot - Air Weld
Approved Insulation Compatiblewith Contact Adhesive 5000
Drain PE as overflow drain
Hot - Air Weld
Approved Adhesive
Butyl tape
Prelasti Membrane
Approved Adhesive
Vapour Barrier
Gravel
Protection layer. Can be left out ifgravel is river washed fraction 16/32without crushed stones
Prelasti Membrane
SCALE: N/A PRE-313
Overflow drain detail fora warm roof with a gravelballast
15/08/2012
SealEcoP.O. Box 514SE 331 25 Vä[email protected]
AS A SUPPLIER OFMATERIAL ONLY,SEALECO NOT ASSUMERESPONSIBILITY FORDESIGN, ENGINEERING,QUANTITIES ORDIMENSIONS. THESPECIFIER, ENGINEERAND/OR ROOFINGAPPLICATOR SHALLVERIFY ALL DIMENSIONSAND SIZES
Deck
Hot - Air Weld
Approved Insulation Compatiblewith Contact Adhesive 5000
Drain PE as overflow drain
Hot - Air Weld
Approved Adhesive
Butyl tape
Prelasti Membrane
Approved Adhesive
Vapour Barrier
Gravel
Protection layer. Can be left out ifgravel is river washed fraction 16/32without crushed stones
Prelasti Membrane
SCALE: N/A PRE-313
Overflow drain detail fora warm roof with a gravelballast
15/08/2012
SealEcoP.O. Box 514SE 331 25 Vä[email protected]
AS A SUPPLIER OFMATERIAL ONLY,SEALECO NOT ASSUMERESPONSIBILITY FORDESIGN, ENGINEERING,QUANTITIES ORDIMENSIONS. THESPECIFIER, ENGINEERAND/OR ROOFINGAPPLICATOR SHALLVERIFY ALL DIMENSIONSAND SIZES
7:22 | Sept 2012
SealEcoPost Address: P.O. Box 514, SE-331 25 Värnamo, Sweden
Phone: +46 (0) 370 510 100, Fax: +46 (0) 370 510 101, Email: [email protected], www.sealeco.com Sept 2012 | 7:23
PRE-401 Expansion joint for an inverted roof with a paver ballast - plywood or synthetic bridge
PRE-402 Expansion joint for an inverted roof with a gravel ballast - plywood or synthetic bridge
EXPANSION JOINT DETAILS
Approved Insulation
Prelasti Membrane
Plywood orSynthetic Bridge
Deck, equal tofloated concrete
400mm Minimum
Separation layer
Pavers
Sand layer or paversupports
Protection layer
Expansion joint for aninverted roof with a paverballast - Plywood orsynthetic bridge
SCALE: N/A PRE-401
SealEcoP.O. Box 514SE 331 25 Vä[email protected]
AS A SUPPLIER OFMATERIAL ONLY,SEALECO NOT ASSUMERESPONSIBILITY FORDESIGN, ENGINEERING,QUANTITIES ORDIMENSIONS. THESPECIFIER, ENGINEERAND/OR ROOFINGAPPLICATOR SHALLVERIFY ALL DIMENSIONSAND SIZES
15/08/2012
Approved Insulation
Prelasti Membrane
Protection layer. Can beleft out if gravel is riverwashed fraction 16/32without crushed stones
Gravel
Deck, equal tofloated concrete
400mm Minimum
Plywood orSynthetic Bridge
Protection layer Expansion joint for aninverted roof with a gravelballast - Plywood orsynthetic bridge
SCALE: N/A PRE-402
SealEcoP.O. Box 514SE 331 25 Vä[email protected]
AS A SUPPLIER OFMATERIAL ONLY,SEALECO NOT ASSUMERESPONSIBILITY FORDESIGN, ENGINEERING,QUANTITIES ORDIMENSIONS. THESPECIFIER, ENGINEERAND/OR ROOFINGAPPLICATOR SHALLVERIFY ALL DIMENSIONSAND SIZES
15/08/2012
SealEcoPost Address: P.O. Box 514, SE-331 25 Värnamo, Sweden
Phone: +46 (0) 370 510 100, Fax: +46 (0) 370 510 101, Email: [email protected], www.sealeco.com
PRE-403 Expansion joint for a cold roof with a timber deck - plywood or synthetic bridge
PRE-404 Expansion joint for a cold roof with a gravel ballast - plywood or synthetic bridge
EXPANSION JOINT DETAILS
Prelasti Membrane
Protection layer
Timber Deck
Timber runners
Deck, equal tofloated concrete
400mm Minimum
Plywood orSynthetic Bridge
Protection layer
Expansion joint for a coldroof with a timber deck -Plywood or syntheticbridge
SCALE: N/A PRE-403
SealEcoP.O. Box 514SE 331 25 Vä[email protected]
AS A SUPPLIER OFMATERIAL ONLY,SEALECO NOT ASSUMERESPONSIBILITY FORDESIGN, ENGINEERING,QUANTITIES ORDIMENSIONS. THESPECIFIER, ENGINEERAND/OR ROOFINGAPPLICATOR SHALLVERIFY ALL DIMENSIONSAND SIZES
15/08/2012
Prelasti Membrane
Gravel
Deck, equal tofloated concrete
Protection layer. Can be left outif gravel is river washed fraction16/32 without crushed stones
400mm Minimum
Plywood orSynthetic Bridge
Protection layer
Expansion joint for a coldroof with a gravel ballast -Plywood or syntheticbridge
SCALE: N/A PRE-404
SealEcoP.O. Box 514SE 331 25 Vä[email protected]
AS A SUPPLIER OFMATERIAL ONLY,SEALECO NOT ASSUMERESPONSIBILITY FORDESIGN, ENGINEERING,QUANTITIES ORDIMENSIONS. THESPECIFIER, ENGINEERAND/OR ROOFINGAPPLICATOR SHALLVERIFY ALL DIMENSIONSAND SIZES
15/08/2012
7:24 | Sept 2012
SealEcoPost Address: P.O. Box 514, SE-331 25 Värnamo, Sweden
Phone: +46 (0) 370 510 100, Fax: +46 (0) 370 510 101, Email: [email protected], www.sealeco.com Sept 2012 | 7:25
PRE-405 Expansion joint for an inverted roof with a paver ballast - metal bridge
PRE-406 Expansion joint for an inverted roof with a gravel ballast - metal bridge
EXPANSION JOINT DETAILS
Approved Insulation
Prelasti Membrane
Metal bridge,fastened to oneside only
Deck, equal tofloated concrete
Separation layer
Pavers
Sand layer
Protection layer
Expansion joint for aninverted roof with a paverballast - metal bridge
SCALE: N/A PRE-405
SealEcoP.O. Box 514SE 331 25 Vä[email protected]
AS A SUPPLIER OFMATERIAL ONLY,SEALECO NOT ASSUMERESPONSIBILITY FORDESIGN, ENGINEERING,QUANTITIES ORDIMENSIONS. THESPECIFIER, ENGINEERAND/OR ROOFINGAPPLICATOR SHALLVERIFY ALL DIMENSIONSAND SIZES
15/08/2012
Approved Insulation
Prelasti Membrane
Separation layer
Gravel
Deck, equal tofloated concrete
Metal bridge, fastenedto one side only
Protection layer Expansion joint for aninverted roof with a gravelballast - metal bridge
SCALE: N/A PRE-406
SealEcoP.O. Box 514SE 331 25 Vä[email protected]
AS A SUPPLIER OFMATERIAL ONLY,SEALECO NOT ASSUMERESPONSIBILITY FORDESIGN, ENGINEERING,QUANTITIES ORDIMENSIONS. THESPECIFIER, ENGINEERAND/OR ROOFINGAPPLICATOR SHALLVERIFY ALL DIMENSIONSAND SIZES
15/08/2012
SealEcoPost Address: P.O. Box 514, SE-331 25 Värnamo, Sweden
Phone: +46 (0) 370 510 100, Fax: +46 (0) 370 510 101, Email: [email protected], www.sealeco.com
PRE-407 Expansion joint for a cold roof with a timber deck - metal bridge
PRE-408 Expansion joint for a cold roof with a gravel ballast - metal bridge
EXPANSION JOINT DETAILS
Prelasti Membrane
Gravel
Deck, equal tofloated concrete
Protection layer. Can be left out ifgravel is river washed fraction16/32 without crushed stones
Metal bridge, fastenedto one side only
Protection layer
Expansion joint for a coldroof with a gravel ballast -metal bridge
SCALE: N/A
15/08/2012
PRE-408
SealEcoP.O. Box 514SE 331 25 Vä[email protected]
AS A SUPPLIER OFMATERIAL ONLY,SEALECO NOT ASSUMERESPONSIBILITY FORDESIGN, ENGINEERING,QUANTITIES ORDIMENSIONS. THESPECIFIER, ENGINEERAND/OR ROOFINGAPPLICATOR SHALLVERIFY ALL DIMENSIONSAND SIZES
7:26 | Sept 2012
SealEcoPost Address: P.O. Box 514, SE-331 25 Värnamo, Sweden
Phone: +46 (0) 370 510 100, Fax: +46 (0) 370 510 101, Email: [email protected], www.sealeco.com Sept 2012 | 7:27
PRE-501 Wall flashing details - Reglet counterflashing
PRE-502 Wall flashing details - Surface mounted counterflashing
WALL FLASHING DETAILS
200m
m m
inim
um
Reglet counterflashing
Approved Sealant
Approved Fastenerspaced @ 200mm O.C.
Prealsti Membrane orThermobondreinforced splice strip
Finished roofsurface
Approved Adhesive
SCALE: N/A PRE-501
Reglet counterflashing
SealEcoP.O. Box 514SE 331 25 Vä[email protected]
AS A SUPPLIER OFMATERIAL ONLY,SEALECO NOT ASSUMERESPONSIBILITY FORDESIGN, ENGINEERING,QUANTITIES ORDIMENSIONS. THESPECIFIER, ENGINEERAND/OR ROOFINGAPPLICATOR SHALLVERIFY ALL DIMENSIONSAND SIZES
15/08/2012
SealEcoPost Address: P.O. Box 514, SE-331 25 Värnamo, Sweden
Phone: +46 (0) 370 510 100, Fax: +46 (0) 370 510 101, Email: [email protected], www.sealeco.com
PRE-503 Wall flashing details - Clad Wall panel system counterflashing
WALL FLASHING DETAILS
Approved Adhesive
Metal counterflashing
Wall cladding
200m
m M
inim
um
Approved Fastener spaced@ 200mm O.C. with SeamPlate or termination bar
Finished roofsurface
SCALE: N/A PRE-503
Clad Wall panel systemcounterflashing
SealEcoP.O. Box 514SE 331 25 Vä[email protected]
AS A SUPPLIER OFMATERIAL ONLY,SEALECO NOT ASSUMERESPONSIBILITY FORDESIGN, ENGINEERING,QUANTITIES ORDIMENSIONS. THESPECIFIER, ENGINEERAND/OR ROOFINGAPPLICATOR SHALLVERIFY ALL DIMENSIONSAND SIZES
15/08/2012
7:28 | Sept 2012
SealEcoPost Address: P.O. Box 514, SE-331 25 Värnamo, Sweden
Phone: +46 (0) 370 510 100, Fax: +46 (0) 370 510 101, Email: [email protected], www.sealeco.com Sept 2012 | 7:29
PRE-601 Multi - System Roof tie-in
Butyl tape
Hot air weld
Prelasti Membrane
Approved insulation
Vapour Barrier
Deck
Approved Adhesive
Thermobond reinforced splicestrip
Wooden curb
Metal counterflashing fastened@ 200mm O.C. maximum
Approved Sealant
Existing roof
200m
m m
inim
um
Approved fasteners spaced @200mm O.C. with Seam Plate orTermination Bar
Multi System Roof tie-in
SCALE: N/A PRE-601
SealEcoP.O. Box 514SE 331 25 Vä[email protected]
AS A SUPPLIER OFMATERIAL ONLY,SEALECO NOT ASSUMERESPONSIBILITY FORDESIGN, ENGINEERING,QUANTITIES ORDIMENSIONS. THESPECIFIER, ENGINEERAND/OR ROOFINGAPPLICATOR SHALLVERIFY ALL DIMENSIONSAND SIZES
15/08/2012
MULTI SYSTEM ROOF TIE-IN DETAILS
