Pin & Vee Block Test Machine - Auburn University
Transcript of Pin & Vee Block Test Machine - Auburn University
ASTM Standards D 2670, D2626, D3233, D5620
Federal Test Methods FTM-791-3807.1, FTM-791-3812.1
Chrysler Corporation 461-C-84-01, 461-C-84-02, 461-C-84-03
Ford Motor Company FMC-BJ1-1
Institute For Petroleum IP 241
Used in Standard Test Methods
Pin & Vee Block Test Machine
Fluid and Dry Lubricants
Additive Packages and Base Stocks
Dry Film Bonded Coatings
Materials
Hardface Coatings
Metal Working Lubricants
Refrigerant Lubricants
Picture of the apparatus
Suitable for Testing
GENERAL INFORMATION
The Falex Pin & Vee Block Test Machine is a laboratory tool for evaluating
wear, friction and extreme pressure properties of materials and lubricants.
The equipment rotates a 1/4 inch diameter test pin (journal) against two 1/2 inch diameter vee blocks. A four line contact region is established as load is applied through a mechanical gage by a ratchet wheel and an eccentric arm.
LOAD:
Load is applied to the vee blocks against a rotating test pin by use of a ratchet wheel mechanism and spring type gage. The Falex Dual Range Load Gage applies from 200 to 3000 lbs direct load (4500 lbs reference load) ±2% full scale accuracy, up to 300 psi average initial Hertzian stress.
Optional low load gage (200 to 800 lbs) is available when improved accuracy at low loads is needed.
Electronic load systems provide digital display of 3000 lbs direct load gage.
SPEED:
Shaft speed: 290 rpm ±10 rpm (18.98 ft/min)
WEAR:
Ratchet wheel system allows rate of wear measurement during test and total wear.
14.4 ratchet teeth = 0.001 inch (0.025 mm)
TORQUE:
0 to 100 in-lb load cell with digital display. Accuracy ± 2% full scale.
ENVIRONMENT:
Dry or lubricated
Pin & Vee Block Configuration
Test Area
SPECIFICATIONS AND FEATURES
SYSTEM DESCRIPTION
The Pin & Vee Block Test Machine is offered in two models:
F-1500C Pin & Vee Block Test Machine with Data Acquisition and Control System
System Includes Standard Pin and Vee Block Machine equipped with Digital Load Gage and Ratchet Wheel Assembly, Sample Fluid Cup, Heater Control, Shear Pin Clip, Puller, and Knock-out Tool, and Falex PC Based Data Acquisition and Control System. (PC Kit Included)
Options for Falex 301 Test Data Acquisition System
000-001-001 Falex Pin & Vee Block Test Machine with 301 Test Data Acquisition System
System Includes Standard Pin and Vee Block Test Machine equipped with Digital Load Gage and Ratchet Wheel Assembly, Sample Fluid Cup, Manual Heater Control, Shear Pin Clip, Puller and Knock-out Tool, and Falex PC Based Data Acquisition System. Requires optional PC Kit or customer supplied PC with Windows® XP Operating System)
F-1500AL Automatic Loading Option:
Provides controlled maintenance of test load. User programmable test load and differential load point for the automatic maintenance of test loads. User defined and Standard Test Load Pro-grams for evaluating wear and extreme pressure properties of fluid lubricants and bonded solid lubricants. Load is applied in positive direction only. Option available with systems using the Falex SoftWEAR
TM Data Acquisition Program. Available with new units or as a kit for field instal-
lation on existing units.
F-1500-24 Wear Measurement Display:
For use with the F-1500C Pin & Vee Block Test Machine with Data Acquisition System to display wear as indicated in number of ratchet teeth or inches. Available with new units or as a kit for field installation on existing units.
000-201-301 Digital Load Assembly for Falex 301 Data System:
For use with the Falex Data Acquisition System to display Test Load and Coefficient of Friction Values. Available with new units or as a kit for field installation on existing units.
F-1500-301-TFT Digital Test Fluid Temperature Assembly for Falex 301 Data System:
For use with the Falex Data Acquisition System to display Test Fluid Temperature Values. Available with new units or as a kit for field installation on existing units.
Options for Data Acquisition and Control System
PIN & VEE BLOCK OPTIONS & ACCESSORIES
F-1500CU Falex SoftWEARTM Data Acquisition System
Upgrade:
For use with the standard Falex Pin and Vee Block Test machines. Provides users of current machines to acquire and store friction, load, and temperature signals at user-selected predetermined time intervals. Data is presented in real time graphic and alpha numeric (spreadsheet) format compatible with Excel® and other commercial spreadsheet programs. Load displayed in Direct Load (150 to 3000 Lb) or Reference Load (200 to 4500 Lb) scales. Coefficient of friction and optional wear data are calculated and displayed simultaneously. Complete system with PC,Falex SoftWEARTM program, and electronic interface. F-1500AL Automatic Loading capability can be added for programmable control of loading.
F-1500-11 Dual Range Load Gage:
Combines 3000 lb Direct Reading and 4500 lb Reference Reading Load Scales on a Single Gage
F-1500-26 High Pressure Test Chamber:
Sealed chamber surrounding test area and fluid reservoir for performing evaluations of test oil saturated with refrigerant or other gases. Prevents gases from escaping continuously into atmosphere. Capable of initial temperatures from ambient room temperature to 150°C (302°F) and pressures from atmospheric to 225 psig. Pressure source not included.
PLEASE NOTE: This must be installed on a new Pin & Vee Block Test Machine by factory trained personnel; it cannot be field installed.
PIN & VEE BLOCK OPTIONS & ACCESSORIES (continued)
F-1500-31A High Precision Scar Measurement System:
Binocular microscope with X-Y base and digital display of measurement accurate to 0.001 mm.
F-1500-31B Digital Scar Measurement System:
Binocular microscope with CCD camera for on screen measurement to 0.01 mm.
F-1500-36 Load Calibration Kit:
Includes one Brinell ball, back-up plug, support block and copper Brinell coupon.
F-1500-36A Copper Brinell Coupon:
Used for checking calibration of load gage. BHN 37-39
000-107-002 Electronic Load and Torque Calibration Assembly:
System includes a high precision digital meter for displaying load and torque values and load cells and fixturing for calibration of test load and torque.
657-000-008 Calibration Fluid Blend A:
0.5 liter, 0.10% Sulfur Calibration Fluid per ASTM D2670
657-000-009 Calibration Fluid Blend B:
0.5 liter, 0.20% Sulfur Calibration Fluid per ASTM D2670
F-1500-37A Shear pin Clip and Puller:
Clip holds shear pin secure during test and puller facilitates removal of clip.
F-1500-37B Thermocouples:
Thermocouple used to measure fluid temperature during testing. For use with F-1500-32.
(Included with F-1500C & F-1503 models)
F-1500-37D Shear pin Knock-Out Assembly:
Shear Pin Removal Tool, facilitates safe extraction of brass hear pin from test machine shaft at end of test.
F-1500-37H Reaming Tool:
Used to remove debris from inside test machine shaft at end of test.
TEST SPECIMENS
Power requirements:
220 V, 60 Cycle, Single Phase, 8 Amps (50 Cycle optional)
Shipping information:
Model F-1500 150 lbs (68 kg) 31 in x 31 in x 36 in (79 cm x 79 cm x 91 cm)
Model F-1500C 242 lbs (110 kg) 43 in x 36 in x 42 in (109 cm x 91 cm x 190 cm)
Shipping weights & dimensions are typical and may vary depending options ordered.
Space Requirements:
Bench top: Model F-1500: 30 in x 24 in x 24 in (76 cm x 61 cm x 61 cm)
Models F-1500C 60 in x 24 in x 24 in (152 cm x 61 cm x 61 cm)
PIN & VEE BLOCK UTILITIES & DIMENSIONS
These specimens conform to ASTM Standards: D 2670, D 2625, D 3233 and D 5620
000-500-002 Complete Sets with #8 Test Pin:
Two (2) Standard Vee Blocks (AISI 1137 Steel) , One (1) #8 Test Pin (SAE 3135 Steel),
and One (1) Brass Shear Pin
000-500-003 Complete Sets with #10 Test Pin:
Two (2) Standard Vee Blocks (AISI 1137 Steel) , One (1) #10 Test Pin (SAE 3135 Steel), and One (1) Brass Shear Pin
000-502-100 Standard Falex Vee Blocks:
AISI 1137 Steel, 96° block angle, Rc 20-24, 10 rms maximum
F-1500-51T Standard Falex Vee Block with Thermocouple Hole
AISI 1137 Steel, 96° block angle, Rc 20-24, 10 rms maximum
000-503-017 Standard Falex #8 Test Pin (journal):
SAE 3135 steel, Rb 87-91, 10 rms maximum
000-503-002 Standard Falex #10 Test Pin (journal):
SAE 3135 steel, Rb 100-104, 10 rms maximum
000-005-004 Standard Falex Shear Pins:
1/2 hard yellow brass (ASTM spec. B-16) bag of 50
New Test Specimens
After ASTM D 2670 Wear Test
For All of Your Lubricant and
Materials Testing
Lubricants
Pin and Vee Block
Block-on-Ring
Timken EP
Tapping Torque
Panel Coker
High Temperature/High Speed Bearing
Four Ball Wear
Four Ball EP
High Temperature Wheel Bearing
Thermal Oxidation Stability (L60-1)
Fretting Wear
Hydrolytic Stability
Grease Corrosion Test
Isothermal Oxidation
Hydraulic Fluid Pump Stand (Vickers and Conestoga)
Fuels and Solvents
Ball on Three Disk Fuel Lubricity
Thin Film Evaporator
Fuel Deposit Simulator
Materials
Journal Bearing
Multi-Specimen
Crossed Cylinders
Low Velocity Friction Apparatus
Pin on Disk
Coefficient of Stoption
Magnetic Media and Paper Wear
Life Performance Face Clutch System
Thin Coating Wear (Electrical Contacts)
Dual Drive Rolling Contact Fatigue
High Speed Bearing/Mechanical Clutch
Abrasion and Erosion
Dry Sand/Rubber Wheel
Air Jet Erosion
Miller Number Slurry
Distributed by:
www.compass-instruments.com
1020 Airpark Drive Sugar Grove, IL 60554 630.556.4835 630.556.3679 fax