PIC-H1 - Picture Lift Mechanism Technical Sheet ISSUE...
3
UP POSITION DOWN POSITION Mechanism Width 989 38.9 (For All Models PIC-H 1 / PIC-H 2 / PIC-H 3) Mechanism Frame Width 967 38.1 (For All Models PIC-H 1 / PIC-H 2 / PIC-H 3) FUNCTION This mechanism will move a panel vertically to reveal a screen behind. SUITABILITY This technical sheet uses the smallest version (PIC-H 1) of the mechanism as an example. SPECIFYING The mechanism requires the screen to be recessed into the wall. Maximum panel weight is 35kg [77.23lb]. CONTROL Supplied with basic infrared remote. Can be learnt by many learning remotes. Also has switch control and RS232 so can be operated by relays, switches, Crestron / AMX or Lutron systems. DESIGN HIGHLIGHTS Quiet smooth motion • Stylish look and finish • OPTIONS PIC-H 2 size also available • (for maximum travel of 860 [33.9]) PIC-H 3 size also available • (for maximum travel of 1010 [39.8]) PIC-H Custom sizes also available • NOTE All dimensions are • measured in mm [in] WARNING It is the responsiblity of the installer to warn all potential end users of the dangers of interfering with mechanisms during operation IMPORTANT Mechanisms which lift or move weights need to be checked on a yearly basis for any damage which may result in an accident www.futureautomation.co.uk tel: +44 (0) 1438 833 577 fax: +44 (0) 1438 833 565 PIC-H1 - Picture Lift Mechanism Technical Sheet ISSUE 006 SHEET 1 of 3
Transcript of PIC-H1 - Picture Lift Mechanism Technical Sheet ISSUE...
UP POSITION
DOWN POSITION
Mechanism Width 989 38.9
(For All Models PIC-H 1 / PIC-H 2 / PIC-H 3)
Mechanism Frame Width 967 38.1
(For All Models PIC-H 1 / PIC-H 2 / PIC-H 3)
FUNCTIONThis mechanism will movea panel vertically to reveal
a screen behind.
SUITABILITYThis technical sheet
uses the smallestversion (PIC-H 1)of the mechanism
as an example.
SPECIFYINGThe mechanism requires
the screen to berecessed into the wall.
Maximum panel weightis 35kg [77.23lb].
CONTROLSupplied with basic infrared
remote. Can be learnt bymany learning remotes.
Also has switch control andRS232 so can be operated by
relays, switches, Crestron /AMX or Lutron systems.
DESIGN HIGHLIGHTS
Quiet smooth motion•
Stylish look and finish•
OPTIONS
PIC-H 2 size also available •(for maximum travel of 860 [33.9])
PIC-H 3 size also available •(for maximum travel of 1010 [39.8])
PIC-H Custom sizes also available•
NOTE
All dimensions are •measured in mm [in]
WARNINGIt is the responsiblity ofthe installer to warn allpotential end users of
the dangers of interferingwith mechanisms during
operation
IMPORTANTMechanisms which liftor move weights need
to be checked on ayearly basis for anydamage which mayresult in an accident
www.futureautomation.co.uk tel: +44 (0) 1438 833 577 fax: +44 (0) 1438 833 565
PIC-H1 - Picture Lift Mechanism Technical SheetISSUE 006
SHEET 1 of 3
Pic
ture
Tra
vel 7
1028
.0P
ictu
re In
tern
alFr
ame
Hei
ght 9
1035
.8
Minimum Picture Internal Frame Width 1055 41.5
A
A
Pic
ture
Tra
vel 7
1028
.0
UP POSITION10
03.
9
100
3.9
B
B
DOWN POSITIONPROCEDURE:
Decide the required 'Picture 1.Travel'. Ensuring the screen recess height is accounted for and shall be covered by the picture.
Select mechanism based on 2.'Picture Travel' and 'Mechanism Frame Height' using Mechanism Selection/Sizing Table.
Ensure Picture is larger than 3.the 'Mechanism Frame'.
Mechanism Details
NOTE: Custom sized mechanisms are available to suit specific requirements
MECHANISM SELECTION / SIZING TABLE
MECHANISM PICTURE TRAVEL MECHANISM FRAME HEIGHT
PIC-H 1 710 [28.0] 910 [35.8]PIC-H 2 860 [33.9] 1060 [41.7]PIC-H 3 1010 [39.8] 1210 [47.6]
PIC-H CUSTOM CUSTOM HEIGHT - 200 [7.9] CUSTOM HEIGHT
www.futureautomation.co.uk tel: +44 (0) 1438 833 577 fax: +44 (0) 1438 833 565
PIC-H1 - Picture Lift Mechanism Technical SheetISSUE 006
SHEET 2 of 3
Mechanism Cutout Width1000 39.4
C
C
D
Mec
hani
smC
utou
t Hei
ght 1
345.
3
MinimumPictureInternalDepth
32 1.3
Picture-WallClearance
10 0.4
MinimumMechanism
Cutout Depth80 3.1
351.
4
Mov
ing
Pan
elFr
ame
Thic
knes
s
602.
4
DETAIL D
Mounting Details
NOTE:
The screen should be mounted in a recess with suitable clearance around it for ventilation and mounting.
The depicted representaive setup has the screen mounted on a Future Automation V74 product.
CONTROL & SIGNAL:
A control box (measuring 220mm X 130mm X 50mm) shall need to be located in an easily accessible location.
A four-core mains power cable shall need to be routed from the control box to the mechanism.
A 1500mm long infrared lead shall be connected to the control box.
PICTURE PANEL:
The maximum moving panel weight that the mechanism can lift is 35kg [77.2lb].
Custom designs can be made to lift more; all custom designs have extra costs and longer lead times.
www.futureautomation.co.uk tel: +44 (0) 1438 833 577 fax: +44 (0) 1438 833 565
PIC-H1 - Picture Lift Mechanism Technical SheetISSUE 006
SHEET 3 of 3
