PETUNJUK PEMASANGAN TUDUNG HISAP … MANUAL FOR COOKER HOOD 1. Check strength of wall, please...
-
Upload
phunghuong -
Category
Documents
-
view
218 -
download
0
Transcript of PETUNJUK PEMASANGAN TUDUNG HISAP … MANUAL FOR COOKER HOOD 1. Check strength of wall, please...
ACCESSORIES NAMA PART GAMBAR PEMAKAIAN
L - BRACKET
SCREW FISHER
For : RH-60V/RH-71V/RH-90VRH-60VI/RH-71VI/RH-90VIRH-60EV/RH-71EV/RH-90EVRH-60EVI/RH-71EVI/RH-90EVI
EXHAUST
SOFT TAPE
2 pcs
(Ø5,1 x 25)
(Ø5 x 40)
4 pcs
2 pcs
1 pc
1 pc
(FOR RH - 60V / RH - 71V / RH - 90V)(FOR RH - 60VI / RH - 71VI / RH - 90VI)(FOR RH - 60EV / RH - 71EV / RH - 90EV)(FOR RH - 60EVI / RH - 71EVI / RH - 90EVI)
For : RH-60V/RH-71V/RH-90VRH-60VI/RH-71VI/RH-90VIRH-60EV/RH-71EV/RH-90EVRH-60EVI/RH-71EVI/RH-90EVI
PETUNJUK PEMASANGAN TUDUNG HISAPCARA PEMASANGAN PERIKSA AKSESORIS SEBELUM PEMASANGAN
1.PERHATIAN SEBELUM PEMASANGAN 2. PERSIAPAN SEBELUM PEMASANGAN
1. Check kekuatan dinding, pasang tudung hisap pada dinding yang dapat menahan berat tudung hisap (15.0 kg).
(1). Dinding Kayu.
tudung hisap
tudung hisap
• Bila tebal dinding lebih dari 20 mm, bisa dipasang langsung ke dinding.
• Bila tebal dinding kurang dari 20 mm, pasang penguat terlebih dahulu, kemudian pasang pada penguat tersebut.
(2). Dinding Beton
• Pasang penguat kedinding atau menggunakan screw fisher.
(3). Dinding Bata
• Pasang penguat pada tiang
2. Standard Pemasangan
Standard pemasangan tinggi 1600 mm dari lantai, dan 800 mm dari kompor gas. (Gambar No.1).
1. Pasang Casing SupportPasang L bracket casing support dibagian atas casing dengan 4 buah screw. (Gambar No. 2)(Buka dahulu screw dari casing sebelum pemasangan).
2. Pemasangan ExhaustUntuk :
RH-60V / RH-71V / RH-90VRH-60VI / RH-71VI / RH-90VIRH-60EV / RH-71EV / RH-90EVRH-60EVI / RH-71EVI / RH-90EVI
Pasang soft tape ke exhaust, pastikan masuk kedalam bagian casing yang berongga, kemudian putar searah jarum jam sampai berhenti kemudian kencangkan/pasang dengan 1 buah screw. (Gambar No. 3)(Buka screw dari body sebelum digunakan).
3. PEMASANGAN TUDUNG HISAP
1. Gunakan Casing Support (L-Bracket)1. Pasang screw fisher ke dinding
Pasang screw fisher (Ø5,1 x 25) pada posisi sementara pemasangan 5 mm dari permukaan dinding.(RHS, LHS masing-masing 1 buah) (Gambar No. 4)
2. Pemasangan Casing (Gambar. No. 5)1. Masukan lubang penggantung casing
support pada screw fisher.2. Kencangkan screw casing dengan kuat.3. Kencangkan dengan kuat screw fisher
(Ø5,1 x 25) pada dinding.
2. Pemasangan langsung pada langit-langit1. Pasang screw fisher ke langit-langit (Ø5,1 x
25) pada posisi sementara pada langit-langit (R/L masing-masing 1 buah) 5 mm dari permukaan langit-langit. (Gambar No. 6)
3. Pemasangan Casing pada langit-langit(1). Gantung casing pada langit-langit
dengan screw fisher pada lubang penggantung yang terdapat di bagian atas casing.
(2). Kencangkan screw fisher
.
2. Buka Oil PanelLepas 3 buah screw. (Gambar No. 7)
(Ø5,1 x 25 2 buah) pada lubang pengantung dibagian belakang casing kedinding. (Gambar No. 8)
(3) Pastikan screw fisher sudahdikencangkan pada langit- langit.
3. Pemasangan dengan slide rail1. Masukan casing pada slide rail
(Gambar No. 9) masukan penuh ke dalam.
4. PENGGABUNGAN BAGIAN DUCTING
Untuk : RH-60V / RH-71V / RH-90VRH-60VI / RH-71VI / RH-90VIRH-60EV / RH-71EV / RH-90VIRH-60EVI / RH-71EVI / RH-90EVI
terlalu panjang karena dapat mengurangi tekanan.
• Sambung exhaust dan exhaust duct Ø150. (Gambar No. 10)
• Jangan menggunakan flexible duct yang
5. PERCOBAAN PENGOPERASIAN
1. Electric SupplyMasukan steker listrik ke stop kontak.
2. Percobaan PengoperasianCoba fungsi dengan menekan masing-masing tombol, periksa kondisi exhaust dan kondisi suara getaran.
1. Ketika akan memasang , perhatikan bahwa tidak boleh bersentuhan dengan metal part (Bagian dari dalam dinding atau sebagainya di dalam rumah).
2. Jangan memasang atau mengencangkan body tudung hisap di dalam dinding karena akan menyebabkan kebocoran arus listrik, apabila penguat dalam dinding bersentuhan dengan casing tudung hisap.
3. Gunakan selalu kompor yang cocok lebarnya dengan tudung hisap.
4. Jangan pernah memakai tudung hisap dengan tombol modifikasi, dll.
5. Pembuangan udara dari lubang pembuangan seharusnya tidak mempengaruhi kondisi api dari pada kompor.
tudung hisap tudung hisap
CATATAN SAAT PEMASANGAN
DIMENSI PRODUK
NAMA PART
Untuk pemasangan
Casing
Untuk pemasangandinding kayu
Untuk penghubung
antara CasingdenganDucting
Untuk menutup ronggaExhaust
dgn Ducting
http://www.rinnai.co.id
LAYANAN BEBAS PULSA: 0800-1-889-889SMS Center : 0815-112-99999
PT. RINNAI INDONESIATangerang - Indonesia
NOMOR TANDA PENDAFTARAN
DIRJEN PDN NO: P.41.RI15.00201.0710
BAHASA INDONESIA
013013
Untuk pemasangandinding beton
INSTALLATION MANUAL FOR COOKER HOOD
1. Check strength of wall, please install cooker hood to wall
which can hold weight of product. (15.0 kg).
(1). Wooden Wall
• When the thickness of wall is more than 20 mm,
install to wall directly.
• When the thickness of wall is less than 20 mm, fix
reinforcement first, then install cooker hood to
reinforcement.
(2). Concrete, Tail Wall
• Fix reinforcement to wall or use curl plug.
(3). Soil Wall
• Fix reinforcement to pillar first
2. Standard way of installation
Standard installation height of cooker hood 1600 mm
from floor, and 800 mm from gas cooker. (Fig.1).3. INSTALLATION OF COOKER HOOD
1. Using Casing Support (L-Bracket)1. Thrust screw fisher into wall.
Thrust screw fisher (Ø5.1 x 25) to temporary position of fixing at fig. -1(RHS, LHS each 1 pc) 5 mm from wall surface. (Fig. 4)
2. Install Casing (Fig. 5)1. Fix hang hole of casing support
with screw fisher.2. Tighten screw of casing firmly.3. Tighten screw fisher of wall firmly
(Ø5.1 x 25)
4. CONNECTING DUCT PARTS
For : RH-60V/RH-71V/RH-90VRH-60VI/RH-71VI/RH-90VIRH-60EV/RH-71EV/RH-90EVRH-60EVI/RH-71EVI/RH-90EVI
• Connect exhaust and exhaust duct by using Ø150 flexible duct. (Fig. 10)
• Do not use too long flexible duct because pressure can reduce.
5. TRIAL OPERATION
1. Electric SupplyInsert electric power plug to outlet.
2. Trial OperationTry the function by pushing each switch button, check exhaust condition and whether there’s vibration noise.
Fig. 1
HOW TO INSTALL
1. CAUTION BEFORE INSTALLATION 2. PREPARATION BEFORE INSTALLATION
1. Fix casing support
Fix L-Bracket casing support to upper part of casing by 4 pcs of screw surely. (Fig. 2)
(Please take out screw which is fixed to body)
2. Fix Exhaust For : RH-60V/RH71V/RH-90V
RH-60VI/RH-71VI/RH-90VIRH-60EV/RH71EV/RH-90EVRH-60EVI/RH-71EVI/RH-90EVI
Put soft tape to exhaust, insert exhaust to notch part of casing surely, and then turn it clockwise until stop, fix by 1 pc od screw. (Fig.3)(Please take out screw which is fixed to body)
3. Install casing on ceiling(1). Hang the casing on the ceiling
with screw fisher through the hang hole of upper part of casing.
(2). Tighten screw fisher (Ø5.1 x 25 2 pcs.) to wall through hang hole of back of casing surely. (Fig. 8)
(3). Tighten screw fisher to ceiling surely. (Fig. 8)
Oil Panel
Screws Fig. 7
Screw Fisher
Screw Fisher Fig. 8
Fig. 9Slide Rail
Exhaust Duct
Flexible Duct
Exhaust
Fig. 10
Screw
Fig. 2
Screw
Exhaust
Soft TapeNotch Part
Fig. 3
5
Fig. 4
Screw Fisher
Fig. 5
5
Fig. 6
Casing Support
3. Installation using slide rail1. Insert casing on slide rail (Fig. 9)
insert fully to inside.
2. Oil Panel 3 screw ( . 7)
RemoveRelease pcs of . Fig
2. Direct installation to ceiling1. Thrust screw fisher into the ceiling
Thrust screw fisher (Ø5.1 x 25) to temporary fixing position on ceiling (R/L each 1 pc) 5 mm from the ceiling surface (Fig. 6)
INSTALLATION MANUAL FOR COOKER HOOD
1. When install cooker hood, be careful that the cooker hood does not come in contact with any metal parts (the lath in the wall or the like) of the house.
2. Do not install or mount the body of the cooker hood inside the wall because leakage current, if any, on the steel mesh inside the wall will come in contact with the casing.
3. Use gas cooker within the width of cooker hood.
4. Do not use cooker hood by modifying switch, etc.
5. Exhaust air discharges from air discharge outlet shall not affect the flame of gas cooker.
NOTICE WHEN INSTALL PARTS NAMEAC Power Cord
Switch
Rectifier Panel
Casing
ENGLISH
PLEASE CHECK ACCESSORIES BEFORE INSTALLATION
DIMENSION OF PRODUCT ACCESSORIESPART NAME SKETCH USAGE
L - BRACKET
SCREW FISHER
For : RH-60V/RH-71V/RH-90VRH-60VI/RH-71VI/RH-90VIRH-60EV/RH-71EV/RH-90EVRH-60EVI/RH-71EVI/RH-90EVI
EXHAUST
SOFT TAPE
2 pcs
(Ø5,1 x 25)
(Ø5 x 40)
4 pcs
2 pcs
1 pc
1 pc
USE FORFIXINGCASING
USE FORCONNECTINGCASING AND
DUCT
USE FORCOVERING
GAP OF EXHAUST AND DUCT
USE FORFIXING
WOODENWALL
USE FORFIXING
CONCRETEWALL
(FOR RH - 60V / RH - 71V / RH - 90V)(FOR RH - 60VI / RH - 71VI / RH - 90VI)(FOR RH - 60EV / RH - 71EV / RH - 90EV)(FOR RH - 60EVI / RH - 71EVI / RH - 90EVI)
For : RH-60V/RH-71V/RH-90VRH-60VI/RH-71VI/RH-90VIRH-60EV/RH-71EV/RH-90EVRH-60EVI/RH-71EVI/RH-90EVI
RIT-0144-4x01