Petroleum Exploration and Extraction Technical Standards ... · Petroleum Exploration and...
Transcript of Petroleum Exploration and Extraction Technical Standards ... · Petroleum Exploration and...
RECOMMENDED STANDARDS SELECTION POLICY 2015
Petroleum Exploration and Extraction Technical Standards Committee
Petroleum Exploration and Extraction Technical Standards Committee
2
Contents
Page
Foreword .......................................................................................................................................................................... 3
1 Scope .................................................................................................................................................................... 4
2 Legislation ......................................................................................................................................................... 4
3 Terms and definitions ................................................................................................................................... 4 3.1 Abbreviations ................................................................................................................................................... 4 3.2 Standards Technical Committee titles ..................................................................................................... 5
4 Selection of suitable Standards .................................................................................................................. 6
5 Rigs and other equipment designed for International use .............................................................. 6
6 List of suitable Standards ............................................................................................................................. 6
7 Standards in the Oil and Gas industry ..................................................................................................... 7 7.1 Introduction ...................................................................................................................................................... 7 7.2 Explanation of Standard designations ..................................................................................................... 7 7.2.1 Standards ........................................................................................................................................................... 7 7.2.2 Technical Specifications ............................................................................................................................... 8 7.2.3 Technical Report ............................................................................................................................................. 8
8 List of Irish National Standards and International Standard for the Oilfield ............................ 9 8.1 Down hole ....................................................................................................................................................... 10 8.2 Subsea drilling and production equipment ........................................................................................ 13 8.3 Surface drilling, production and processing equipment and systems...................................... 14 8.4 Offshore structures (Semi submersibles) ........................................................................................... 16 8.5 Offshore structures (Platforms, jackets and jack-ups) ................................................................... 17 8.6 Pipeline transportation systems ............................................................................................................ 18 8.7 Onshore processing ..................................................................................................................................... 19
9 Information on each Technical Committee......................................................................................... 22 9.1 ISO/TC 67 - Structure .................................................................................................................................. 22 9.1.1 ISO/TC 67 ........................................................................................................................................................ 22 9.1.2 ISO/TC 67/SC 2 .............................................................................................................................................. 25 9.1.3 ISO/TC 67/SC 3 .............................................................................................................................................. 26 9.1.4 ISO/TC 67/SC 4 .............................................................................................................................................. 28 9.1.5 ISO/TC 67/SC 5 .............................................................................................................................................. 31 9.1.6 ISO/TC 67/SC 6 .............................................................................................................................................. 32 9.1.7 ISO/TC 67/SC 7 .............................................................................................................................................. 34 9.1.8 ISO/TC 67/SC 8 .............................................................................................................................................. 35 9.1.9 ISO/TC 67/SC 9 .............................................................................................................................................. 36 9.2 ISO/TC 60 ........................................................................................................................................................ 36 9.3 ISO/TC 115 ...................................................................................................................................................... 39 9.4 ISO/TC 118 ...................................................................................................................................................... 40 9.5 ISO/TC 153 ...................................................................................................................................................... 41 9.6 ISO/TC 192 - Gas turbines ......................................................................................................................... 43 9.7 CEN/TC 12 ....................................................................................................................................................... 45 9.8 CEN/TC 69 ....................................................................................................................................................... 55
Petroleum Exploration and Extraction Technical Standards Committee
3
Foreword
In response to a request from the Commission of Energy Regulation (CER) the NSAI/TC 50 Petroleum Exploration and Extraction Technical Standards Committee (PEETSC) has developed this recommended Standards selection policy document to be applied to petroleum exploration and extraction activities.
This policy recommendation may assist in fulfilling the CER's obligation to consult NSAI with regard to the following provisions of the Petroleum (Exploration and Extraction) Safety Act Number 26 of 2015, namely sections:
13 H (2) (a),
13 L (2) (a) (i),
13 L (3) (c) and
13 L (3) (d).
This document has been prepared for circulation on 12th January 2016
Petroleum Exploration and Extraction Technical Standards Committee
4
1 Scope
This recommendation sets out a policy that can be applied to petroleum undertakings when selecting suitable Standards to be applied for any petroleum activity licensed under the Act.
It recognises the extensive number of Standards available and the fact that many new and revised standards are published every year. It also recognises that, given the nature of the activity, there cannot be an exhaustive list of suitable standards.
This document provides a list of recommended standards that can be to applied petroleum exploration and extraction activities.
2 Legislation
Standards emanating from Standards bodies are not, in themselves, mandatory and only achieve a mandatory status when referenced in legal instruments.
In all cases legislation takes precedence over any voluntary Standard.
3 Terms and definitions
3.1 Abbreviations
ANSI, American National Standards Institute
API; American Petroleum Institute
CEN; European Committee for Standardization
CENELEC; European Committee for Electrotechnical Standardization
CER; Commission of Energy Regulation
ECISS; European Committee for Iron and Steel Standardization
EN; European Standard
ETCI; Electro Technical Counsil of Ireland
IEC; International Electrotechnical Commission
I.S.; Irish Standard
ISO; International Organization for Standardization
NSAI; National Standards Authority of Ireland
PAS; Publicly Available Specification
PEETSC; Petroleum Exploration and Extraction Technical Standards Committee
SC; Subcommittee
S.R.; Standard Recommendation
Petroleum Exploration and Extraction Technical Standards Committee
5
TC; Technical Committee
TR, Technical Report
TS, Technical Specification
3.2 Standards Technical Committee titles
The titles of the Technical Committees listed in this document.
CEN ECISS/TC 110, Steel tubes, and iron and steel fittings
CEN/TC 12, Materials, equipment and offshore structures for petroleum, petrochemical and natural gas industries
CEN/TC 69, Industrial valves
CEN/TC 164/WG 8, Water supply - Sanitary tapware
CENELEC/TC 31, Electrical apparatus for potentially explosive atmospheres
IEC/TC 31, Equipment for explosive atmospheres
IEC/TC 65, Industrial-process measurement, control and automation
ISO/TC 8, Ships and marine technology
ISO/TC 20, Aircraft and space vehicles
ISO/TC 29, Small tools
ISO/TC 60/SC 2, Gears - Gear capacity calculation
ISO/TC 67, Materials, equipment and offshore structures for petroleum, petrochemical and natural gas industries
ISO/TC 67/SC 2, Pipeline transportation systems
ISO/TC 67/SC 4, Drilling and production equipment
ISO/TC 67/SC 5, Casing, tubing and drill pipe
ISO/TC 67/SC 6, Processing equipment and systems
ISO/TC 67/SC 7, Offshore structures
ISO/TC 115/SC 3, Pumps - Installation and special application
ISO/TC 118/SC 1, Compressors and pneumatic tools, machines and equipment- Process compressors
ISO/TC 138, Plastics pipes, fittings and valves for the transport of fluids
ISO/TC 153, Valves
Petroleum Exploration and Extraction Technical Standards Committee
6
ISO/TC 185, Safety devices for protection against excessive pressure
ISO/TC 192, Gas turbines
4 Selection of suitable Standards
4.1 When selecting suitable Standards for petroleum exploration and extraction activities they should be selected in order of preference:
a) Irish Standards Specifications (I.S.);
b) NSAI adoptions of European (EN) and International Standards (ISO);
c) International Standards (ISO).
These publications specify minimum requirements for the relevant activity.
4.2 In the event that a particular activity, covered the Standard types listed in 3.1, is addressed more comprehensively in another publication, undertakings may apply that publication, provided that any requirements contained in the Standard types listed in 3.1 are also met.
In the event that a particular activity is not covered by the Standard types listed in 3.1, undertakings can choose to use publications such as the following:
a) Standards from other National Standards Bodies;
b) Other NSAI publications;
c) Standards from Classification Societies (e.g. Bureau Veritas);
d) Publications from suitable associations (e.g. API).
5 Rigs and other equipment designed for International use
The PEETSC recognises that the building of equipment such as oil rigs is a truly international activity. Most rigs are built to meet the expectations of operators active in other national and international waters. Given this, the selection of Standards used to construct/build such equipment cannot, necessarily follow this policy. However the PEETSC also recognises that such equipment is almost always built to classification society rules in order to operate to the satisfaction of authorities in other jurisdictions.
6 List of suitable Standards
The lists of Standards in Section 8 (correct on the date of compilation) are identified suitable Standards for petroleum exploration and extraction activities. It does not purport to be a comprehensive list but is a guide to the reader of the types of Standards NSAI has recognised as suitable. It is the intention that this list will be updated from time to time but no less than every two years.
Petroleum Exploration and Extraction Technical Standards Committee
7
7 Standards in the Oil and Gas industry
7.1 Introduction
The standards listed in this document are recommended as suitable for application in Ireland. This list is not exhaustive.
The majority of Standards referenced in this document have been developed and published by the International Standards Organisation, ISO, under the Technical Committee ISO/TC 67. Where these ISO Standards can be adopted by Europe directly without modification they are adopted and published by the European Committee for Standardisation (CEN) under Technical Committee CEN/TC 12. Where a modification is required to an ISO Standard CEN/TC 12 publishes the ISO Standard as a European Standard with its own number and develops the European Standard with the specific European requirements.
ISO Standards are not automatically adopted as Irish Standards.
European Standards are automatically adopted as Irish Standards.
Standards relating to Explosive atmospheres are managed by the national committee ETCI/TC 6 which mirrors the work of CENELEC/TC 31 and IEC/TC 31. CEN/TC 305 also develops EN standards specifically for explosive atmospheres.
7.2 Explanation of Standard designations
7.2.1 Standards
A Standard is a document that provides requirements, specifications, guidelines or characteristics that can be used consistently to ensure that materials, products, processes and services are fit for their purpose. Table 1.0 explains the different designations for Standards listed in this document.
Table 1.0 – Designations for Standards
Designation Explanation
I.S. 123 Irish Standard developed and published by NSAI
S.R. 123 Irish Standard Recommendation published by NSAI
EN 12345 European Standard published by CEN/CENELEC
ISO 12345 International Standard published by ISO
IEC 60125 International Standard published by IEC
I.S. EN 12345 European Standard adopted as an Irish Standard
EN ISO 12345 ISO Standard adopted as a European Standard
I.S. EN ISO 12345 European Standard adopted as an Irish Standard
I.S. ISO 12345 ISO Standard adopted as an Irish Standard
Petroleum Exploration and Extraction Technical Standards Committee
8
7.2.2 Technical Specifications
A Technical Specification is a document for which there is the future possibility of agreement on a Standard, but for which at present:
the required support for approval as a Standard cannot be obtained,
there is doubt on whether consensus has been achieved,
the subject matter is still under technical development, or
there is another reason precluding immediate publication as a Standard.
A Technical Specification is not allowed to conflict with an existing Standard. Table 2.0 explains the different designations for Technical Specifications listed in this document.
Table 2.0 – Designations for Technical Specifications
Designation Explanation
CEN/TS 12345 Technical Specification published by CEN
ISO/TS 12345 Technical Specification published by ISO
CEN ISO/TS 12345 ISO Technical Specification adopted as a European Technical Specification
S.R. CEN/TS 12345 European Technical Specification adopted as an Irish Standard Recommendation published by NSAI
S.R. CEN ISO/TS 12345 ISO Technical Specification adopted as a European Technical Specification and adopted as an Irish Standard Recommendation published by NSAI
7.2.3 Technical Report
A Technical Report is a document containing informative material not suitable to be published as a Standard or a Technical Specification. A TR can include, for example, data obtained from a survey carried out among the national members, data on work in other organizations or data on the state of the art in relation to national standards on a particular subject. Table 3.0 explains the different designations for Technical Reports listed in this document.
Table 3.0 – Designations for Technical Specifications
Designation Explanation
CEN/TR 12345 Technical Report published by CEN
ISO/TR 12345 Technical Report published by ISO
CEN ISO/TR 12345 ISO Technical Report adopted as a European Technical Report
S.R. CEN/TR 12345 European Technical Report adopted as an Irish Standard Recommendation published by NSAI
S.R. CEN ISO/TR 12345 ISO Technical Report adopted as a European Technical Report and adopted as an Irish Standard Recommendation
Petroleum Exploration and Extraction Technical Standards Committee
9
8 List of Irish National Standards and International Standard for the Oilfield
The information of the Standards listed is correct as of December 2015. Standards are continuously being revised and developed and the edition of the Standards listed are subject to routine change.
The list of Standards has been separated into 7 process sections for clarity, see Figure 1.0. Standards can be used in the various sections as appropriate.
Key:
1 Down hole, see 8.1
2 Subsea drilling and production equipment, see 8.2
3 Surface drilling, production and processing equipment and systems, see 8.3
4 Offshore structures (Semi submercibles), see 8.4
5 Offshore structures (Platforms, jackets and jack-ups), see 8.5
6 Pipeline transportation systems, see 8.6
7 Onshore processing, see 8.7
Figure 1.0 – Oilfield process sections
Petroleum Exploration and Extraction Technical Standards Committee
10
8.1 Down hole
The Standards listed in this section are specific to down hole equipment. Standards listed are from:
ISO/TC 67/SC 4 – Drilling and production equipment
ISO/TC 67/SC 5 - Casing, tubing and drill pipe
Standards applicable to down hole equipment
S.R. CEN ISO/TR 10400:2011
Petroleum and natural gas industries - Equations and calculations for the properties of casing, tubing, drill pipe and line
pipe used as casing or tubing (ISO/TR 10400:2007)
I.S. EN ISO 10405:2006
Petroleum and natural gas industries - Care and use of casing and tubing (ISO 10405:2006)
ISO 10407:1993
Petroleum and natural gas industries -- Drilling and production equipment -- Drill stem design and operating limits
I.S. EN ISO 10407-2:2008
Petroleum and natural gas industries - Rotary drilling equipment - Part 2: Inspection and classification of used drill stem
elements (ISO 10407-2:2008)
I.S. EN ISO 10414-1:2008
Petroleum and natural gas industries - Field testing of drilling fluids - Part 1: Water-based fluids (ISO 10414-1:2008)
I.S. EN ISO 10414-2:2011
Petroleum and natural gas industries - Field testing of drilling fluids - Part 2: Oil-based fluids (ISO 10414-2:2011)
I.S. EN ISO 10416:2009
Petroleum and natural gas industries - Drilling fluids - Laboratory testing (ISO 10416:2008)
I.S. EN ISO 10417:2004
Petroleum and natural gas industries - Subsurface safety valve systems - Design, installation, operation and redress
(ISO 10417:2004)
I.S. EN ISO 10424-1:2004
Petroleum and natural gas industries - Rotary drilling equipment - Part 1: Rotary drill stem elements (ISO 10424-1:2004)
I.S. EN ISO 10424-2:2007
Petroleum and natural gas industries - Rotary drilling equipment - Part 2: Threading and gauging of rotary shouldered
thread connections (ISO 10424-2:2007)
I.S. EN ISO 10426-1:2009
Petroleum and natural gas industries - Cements and materials for well cementing - Part 1: Specification
(ISO 10426-1:2009)
I.S. EN ISO 10426-2:2003
Petroleum and natural gas industries - Cements and materials for well cementing - Part 2: Testing of well cements
(ISO 10426-2:2003)
I.S. EN ISO 10426-3:2004
Petroleum and natural gas industries - Cements and materials for well cementing - Part 3: Testing of deepwater well
cement formulations (ISO10426-3:2003)
I.S. EN ISO 10426-4:2005
Petroleum and natural gas industries - Cements and materials for well cementing - Part 4: Preparation and testing of
foamed cement slurries at atmospheric pressure (ISO 10426-4:2004)
I.S. EN ISO 10426-5:2005
Petroleum and natural gas industries - Cements and materials for well cementing - Part 5: Determination of shrinkage
and expansion of well cement formulations at atmospheric pressure (ISO 10426-5:2004)
Petroleum Exploration and Extraction Technical Standards Committee
11
I.S. EN ISO 10426-6:2008
Petroleum and natural gas industries - Cements and materials for well cementing - Part 6: Methods for determining the
static gel strength of cement formulations (ISO 10426-6:2008)
I.S. EN ISO 10427-1:2002
Petroleum and natural gas industries - Casing centralizers - Part 1: Bow-spring casing centralizers (ISO 10427-1:2001)
I.S. EN ISO 10427-2:2004
Petroleum and natural gas industries - Equipment for well cementing - Part 2: Centralizer placement and stop-collar
testing (ISO 10427-2:2004)
I.S. EN ISO 10427-3:2004
Petroleum and natural gas industries - Equipment for well cementing - Part 3: Performance testing of cementing float
equipment (ISO 10427-3:2003)
I.S. EN ISO 10432:2005
Petroleum and natural gas industries - Downhole equipment - Subsurface safety valve equipment (ISO 10432:2004)
I.S. EN ISO 11960:2014
Petroleum and natural gas industries - Steel pipes for use as casing or tubing for wells (ISO 11960:2014)
I.S. EN ISO 11961:2008
Petroleum and natural gas industries - Steel drill pipe (ISO 11961:2008)
ISO/PAS 12835:2013
Qualification of casing connections for thermal wells
I.S. EN ISO 13085:2014
Petroleum and Natural gas Industries - Aluminium Alloy Pipe for use as Tubing for Wells (ISO 13085:2014)
I.S. EN ISO 13500:2008+A1:2010
Petroleum and natural gas industries - Drilling fluid materials - Specifications and tests (ISO 13500:2008)
I.S. EN ISO 13501:2011
Petroleum and natural gas industries - Drilling fluids - Processing equipment evaluation (ISO 13501:2011)
I.S. EN ISO 13503-1:2011
Petroleum and natural gas industries - Completion fluids and materials - Part 1: Measurement of viscous properties of
completion fluids (ISO 13503-1:2011)
I.S. EN ISO 13503-2:2006+A1:2009
Petroleum and natural gas industries - Completion fluids and materials - Part 2: Measurement of properties of proppants
used in hydraulic fracturing and gravel-packing operations (ISO 13503-2:2006)
I.S. EN ISO 13503-3:2005
Petroleum and natural gas industries - Completion fluids and materials - Part 3: Testing of heavy brines
(ISO 13503-3:2005)
I.S. EN ISO 13503-4:2006
Petroleum and natural gas industries - Completion fluids and materials - Part 4: Procedure for measuring stimulation and
gravel-pack fluid leakoff under static conditions (ISO 13503-4:2006)
I.S. EN ISO 13503-5:2006
Petroleum and natural gas industries - Completion fluids and materials - Part 5: Procedures for measuring the long-term
conductivity of proppants (ISO 13503-5:2006)
I.S. EN ISO 13503-6:2014
Petroleum and Natural gas Industries - Completion Fluides and Materials - Part 6: Procedure for Measuring Leakoff of
Completion Fluids Under Dynamic Conditions (ISO 13503-6:2014)
I.S. EN ISO 13678:2012
Petroleum and natural gas industries - Evaluation and testing of thread compounds for use with casing, tubing, line pipe
and drill stem elements (ISO 13678:2010)
I.S. EN ISO 13679:2006
Petroleum and natural gas industries - Procedures for testing casing and tubing connections (ISO 13679:2002)
Petroleum Exploration and Extraction Technical Standards Committee
12
I.S. EN ISO 13680:2010
Petroleum and natural gas industries - Corrosion-resistant alloy seamless tubes for use as casing, tubing and coupling
stock - Technical delivery conditions (ISO 13680:2010)
I.S. EN ISO 14310:2008
Petroleum and natural gas industries - Downhole equipment - Packers and bridge plugs (ISO 14310:2008)
I.S. EN ISO 14998:2013
Petroleum and Natural gas Industries - Downhole Equipment - Completion Accessories (ISO 14998:2013)
I.S. EN ISO 15136-1:2009
Petroleum and natural gas industries - Progressing cavity pump systems for artificial lift - Part 1: Pumps
(ISO 15136-1:2009)
I.S. EN ISO 15136-2:2006
Petroleum and natural gas industries - Progressing cavity pump systems for artificial lift - Part 2: Surface-drive systems
(ISO 15136-2:2006)
I.S. EN ISO 15463:2004
Petroleum and natural gas industries - Field inspection of new casing, tubing and plain-end drill pipe (ISO 15463:2003)
I.S. EN ISO 15546:2011
Petroleum and natural gas industries - Aluminium alloy drill pipe (ISO 15546:2011)
I.S. EN ISO 16070:2006
Petroleum and natural gas industries - Downhole equipment - Lock mandrels and landing nipples (ISO 16070:2005)
ISO/TS 16530-2:2014
Well integrity - Part 2: Well integrity for the operational phase
I.S. EN ISO 17078-1:2005+A1:2010
Petroleum and natural gas industries - Drilling and production equipment - Part 1: Side-pocket mandrels
(ISO 17078-1:2004)
I.S. EN ISO 17078-2:2007
Petroleum and natural gas industries - Drilling and production equipment - Part 2: Flow-control devices for side-pocket
mandrels (ISO 17078-2:2007)
I.S. EN ISO 17078-3:2009
Petroleum and natural gas industries - Drilling and production equipment - Part 3: Running tools, pulling tools and kick-
over tools and latches for side-pocket mandrels (ISO 17078-3:2009)
I.S. EN ISO 17078-4:2010
Petroleum and natural gas industries - Drilling and production equipment - Part 4: Practices for side-pocket mandrels and
related equipment (ISO 17078-4:2010)
I.S. EN ISO 17824:2014
Petroleum and Natural gas Industries - Downhole Equipment - Sand Screens (ISO 17824:2009)
I.S. EN ISO 27627:2014
Petroleum and Natural gas Industries - Aluminium Alloy Drill Pipe Thread Connection Gauging (ISO 27627:2014)
I.S. EN ISO 28781:2010
Petroleum and natural gas industries - Drilling and production equipment - Subsurface barrier valves and related
equipment (ISO 28781:2010)
Petroleum Exploration and Extraction Technical Standards Committee
13
8.2 Subsea drilling and production equipment
Standards listed are from:
ISO/TC 67/SC 4 – Drilling and production equipment
Standards applicable to subsea drilling and production equipment
I.S. EN ISO 13628-1:2006+A1:2010
Petroleum and natural gas industries - Design and operation of subsea production systems - Part 1: General
requirements and recommendations (ISO 13628-1:2005)
I.S. EN ISO 13628-2:2006
Petroleum and natural gas industries - Design and operation of subsea production systems - Part 2: Unbonded flexible
pipe systems for subsea and marine applications (ISO 13628-2:2006)
I.S. EN ISO 13628-3:2001
Petroleum and natural gas industries - Design and operation of subsea production systems - Part 3: Through flowline
(TFL) systems (ISO 13628-3:2000)
I.S. EN ISO 13628-4:2010
Petroleum and natural gas industries - Design and operation of subsea production systems - Part 4: Subsea wellhead
and tree equipment (ISO 13628-4:2010)
I.S. EN ISO 13628-5:2009
Petroleum and natural gas industries - Design and operation of subsea production systems - Part 5: Subsea umbilicals
(ISO 13628-5:2009)
I.S. EN ISO 13628-6:2006
Petroleum and natural gas industries - Design and operation of subsea production systems - Part 6: Subsea production
control systems (ISO 13628-6:2006)
I.S. EN ISO 13628-7:2006
Petroleum and natural gas industries - Design and operation of subsea production systems - Part 7: Completion/workover
riser systems (ISO 13628-7:2005)
I.S. EN ISO 13628-8:2006
Petroleum and natural gas industries - Design and operation of subsea production systems - Part 8: Remotely Operated
Vehicle (ROV) interfaces on subsea production systems (ISO 13628-8:2002)
I.S. EN ISO 13628-9:2006
Petroleum and natural gas industries - Design and operation of subsea production systems - Part 9: Remotely Operated
Tool (ROT) intervention systems (ISO 13628-9:2000)
I.S. EN ISO 13628-10:2006
Petroleum and natural gas industries - Design and operation of subsea production systems - Part 10: Specification for
bonded flexible pipe (ISO 13628-10:2006)
I.S. EN ISO 13628-11:2008
Petroleum and natural gas industries - Design and operation of subsea production systems - Part 11: Flexible pipe
systems for subsea and marine applications (ISO 13628-11:2007)
I.S. EN ISO 13628-15:2011
Petroleum and natural gas industries - Design and operation of subsea production systems - Part 15: Subsea structures
and manifolds (ISO 13628-15:2011)
Petroleum Exploration and Extraction Technical Standards Committee
14
8.3 Surface drilling, production and processing equipment and systems
Standards listed are from:
ISO/TC 67, Materials, equipment and offshore structures for petroleum, petrochemical and natural gas industries
ISO/TC 67/SC 4 – Drilling and production equipment
ISO/TC 67/SC 6 - Processing equipment and systems
Standards applicable to surface drilling, production and processing equipment and systems
I.S. EN ISO 10418:2003
Petroleum and natural gas industries - Offshore production installations - Basic surface process safety systems (ISO
10418:2003)
I.S. EN ISO 10423:2009
Petroleum and natural gas industries - Drilling and production equipment - Wellhead and christmas tree equipment (ISO
10423:2009)
I.S. EN ISO 13533:2002
Petroleum and natural gas industries - Drilling and production equipment - Drill-through equipment (ISO 13533:2001)
I.S. EN ISO 13534:2000
Petroleum and natural gas industries - Drilling and production equipment - Inspection, maintenance, repair and
remanufacture of hoisting equipment (ISO 13534:2000)
I.S. EN ISO 13535:2000
Petroleum and natural gas industries - Drilling and production equipment - Hoisting equipment (ISO 13535:2000)
I.S. EN ISO 13626:2004
Petroleum and natural gas industries - Drilling and production equipment - Drilling and well-servicing structures (ISO
13626:2003)
I.S. EN ISO 13702:2015
Petroleum and natural gas industries - Control and migration of fires and explosions on offshore production installations
- Requirements and guidelines (ISO 13702:2015)
I.S. EN ISO 13703:2000
Petroleum and natural gas industries - Design and installation of piping systems on offshore production platforms (ISO
13703:2000)
I.S. EN ISO 14224:2006
Petroleum, petrochemical and natural gas industries - Collection and exchange of reliability and maintenance data for
equipment (ISO 14224:2006)
I.S. EN ISO 14692-1:2002
Petroleum and natural gas industries - Glass-reinforced plastics (GRP) piping - Part 1: Vocabulary, symbols,
applications and materials (ISO 14692-1:2002)
I.S. EN ISO 14692-2:2002
Petroleum and natural gas industries - Glass-reinforced plastics (GRP) piping - Part 2: Qualification and manufacture
(ISO 14692-2:2002)
I.S. EN ISO 14692-3:2002
Petroleum and natural gas industries - Glass-reinforced plastics (GRP) piping - Part 3: System design (ISO 14692-
3:2002)
I.S. EN ISO 14692-4:2002
Petroleum and natural gas industries - Glass-reinforced plastics (GRP) piping - Part 4: Fabrication, installation and
operation (ISO 14692-4:2002)
Petroleum Exploration and Extraction Technical Standards Committee
15
I.S. EN ISO 14693:2003
Petroleum and natural gas industries - Drilling and well-servicing equipment (ISO 14693:2003)
I.S. EN ISO 15138:2007
Petroleum and natural gas industries - Offshore production installations - Heating, ventilation and air-conditioning (ISO
15138:2007)
I.S. EN ISO 15156-1:2015
Petroleum and natural gas industries - Materials for use in H[2]S-containing environments in oil and gas production -
Part 1: General principles for selection of cracking-resistant materials (ISO 15156-1:2015)
I.S. EN ISO 15156-2:2015
Petroleum and natural gas industries - Materials for use in H[2]S-containing environments in oil and gas production -
Part 2: Cracking-resistant carbon and low-alloy steels, and the use of cast irons (ISO 15156-2:2015)
I.S. EN ISO 15156-3:2015
Petroleum and natural gas industries - Materials for use in H[2]S-containing environments in oil and gas production -
Part 3: Cracking-resistant CRAs (corrosion-resistant alloys) and other alloys (ISO 15156-3:2015)
I.S. EN ISO 15544:2010
Petroleum and natural gas industries - Offshore production installations - Requirements and guidelines for emergency
response (ISO 15544:2000, including Amd 1:2009)
I.S. EN ISO 15663-1:2006
Petroleum and natural gas industries - Life cycle costing - Part 1: Methodology (ISO 15663-1:2000)
ISO 15663-2:2001
Petroleum and natural gas industries -- Life-cycle costing -- Part 2: Guidance on application of methodology and
calculation methods
ISO 15663-3:2001
Petroleum and natural gas industries -- Life-cycle costing -- Part 3: Implementation guidelines
I.S. EN ISO 17776:2002
Petroleum and natural gas industries - Offshore production installations - Guidelines on tools and techniques for hazard
identification and risk assessment (ISO 17776:2000)
I.S. EN ISO 20815:2010
Petroleum, petrochemical and natural gas industries - Production assurance and reliability management (ISO
20815:2008, Corrected version 2009-06-15)
I.S. EN ISO 21457:2010
Petroleum, petrochemical and natural gas industries -- Materials selection and corrosion control for oil and gas
production systems
I.S. EN ISO 23936-1:2009
Petroleum, petrochemical and natural gas industries - Non-metallic materials in contact with media related to oil and
gas production - Part 1: Thermoplastics (ISO 23936-1:2009)
I.S. EN ISO 23936-2:2011
Petroleum, Petrochemical and Natural gas Industries - Non-metallic Materials in Contact With Media Related to oil and
gas Production - Part 2: Elastomers (ISO 23936-2:2011)
S.R. CEN ISO/TS 27469:2011
Petroleum, petrochemical and natural gas industries - Method of test for fire dampers (ISO/TS 27469:2010)
I.S. EN ISO 27509:2012
Petroleum and natural gas industries - Compact flanged connections with IX seal ring (ISO 27509:2012)
S.R. CEN ISO/TS 29001:2011
Petroleum, petrochemical and natural gas industries - Sector-specific quality management systems - Requirements for
product and service supply organizations (ISO/TS 29001:2010)
Petroleum Exploration and Extraction Technical Standards Committee
16
8.4 Offshore structures (Semi submersibles)
Standards listed are from:
ISO/TC 67/SC 4 – Drilling and production equipment
ISO/TC 67/SC 7 – Offshore structures
Standards applicable to semi submersibles offshore structures
I.S. EN ISO 13624-1:2009
Petroleum and natural gas industries - Drilling and production equipment - Part 1: Design and operation of marine drilling
riser equipment (ISO 13624-1:2009)
SR CEN ISO/TR 13624-2:2013
Petroleum and natural gas industries -- Drilling and production equipment -- Part 2: Deepwater drilling riser
methodologies, operations, and integrity technical report (ISO/TR 13624-2:2009)
I.S. EN ISO 13625:2002
Petroleum and natural gas industries - Drilling and production equipment - Marine drilling riser couplings
(ISO 13625:2002)
I.S. EN ISO 19901-7:2013
Petroleum and natural gas industries - Specific requirements for offshore structures - Part 7: Stationkeeping systems for
floating offshore structures and mobile offshore units (ISO 19901-7:2013)
I.S. EN ISO 19904-1:2006
Petroleum and natural gas industries - Floating offshore structures - Part 1: Monohulls, semi-submersibles and spars
(ISO 19904-1:2006)
Petroleum Exploration and Extraction Technical Standards Committee
17
8.5 Offshore structures (Platforms, jackets and jack-ups)
Standards listed are from:
ISO/TC 67/SC 4 – Drilling and production equipment
ISO/TC 67/SC 7 – Offshore structures
Standards applicable to Offshore structures (Platforms, jackets and jack-ups)
I.S. EN ISO 19900:2013
Petroleum and natural gas industries - General requirements for offshore structures (ISO 19900:2013)
I.S. EN ISO 19901-1:2006
Petroleum and natural gas industries - Specific requirements for offshore structures - Part 1: Metocean design and operating
considerations (ISO 19901-1:2005)
I.S. EN ISO 19901-2:2005
Petroleum and natural gas industries - Specific requirements for offshore structures - Part 2: Seismic design procedures and
criteria (ISO 19901-2:2004)
I.S. EN ISO 19901-3:2014
Petroleum and natural gas industries - Specific requirements for offshore structures - Part 3: Topsides structure
(ISO 19901-3:2014)
I.S. EN ISO 19901-4:2003
Petroleum and natural gas industries - Specific requirements for offshore structures - Part 4: Geotechnical and foundation design
considerations (ISO 19901-4:2003)
I.S. EN ISO 19901-5:2003
Petroleum and natural gas industries - Specific requirements for offshore structures - Part 5: Weight control during engineering
and construction (ISO 19901-5:2003)
I.S. EN ISO 19901-6:2009
Petroleum and natural gas industries - Specific requirements for offshore structures - Part 6: Marine operations
(ISO 19901-6:2009)
I.S. EN ISO 19901-8:2015
Petroleum and Natural gas Industries - Specific Requirements for Offshore Structures - Part 8: Marine Soil Investigations
(ISO 19901-8:2014)
I.S. EN ISO 19902:2007+A1:2013
Petroleum and natural gas industries - Fixed steel offshore structures (ISO 19902:2007)
I.S. EN ISO 19903:2006
Petroleum and natural gas industries - Fixed concrete offshore structures (ISO 19903:2006)
I.S. EN ISO 19905-1:2012
Petroleum and natural gas industries - Site-specific assessment of mobile offshore units - Part 1: Jack-ups (ISO 19905-1:2012)
SR CEN ISO/TR 19905-2:2013
Petroleum and Natural gas Industries - Sitespecific Assessment of Mobile Offshore Units - Part 2: Jack-ups Commentary and
Detailed Sample Calculation (ISO/TR 19905-2:2012)
I.S. EN ISO 19906:2010
Petroleum and natural gas industries - Arctic offshore structures (ISO 19906:2010)
Petroleum Exploration and Extraction Technical Standards Committee
18
8.6 Pipeline transportation systems
Standards listed are from:
CEN ECISS/TC 110 - Steel tubes, and iron and steel fittings
CEN/TC 12 - Materials, equipment and offshore structures for petroleum, petrochemical and natural gas industries
ISO/TC 67/SC 2 - Pipeline transportation systems
Standards applicable to pipeline transportation systems
I.S. EN ISO 3183:2012
Petroleum and natural gas industries - Steel pipe for pipeline transportation systems (ISO 3183:2012)
ISO 12490:2011
Petroleum and natural gas industries -- Mechanical integrity and sizing of actuators and mounting kits for pipeline valves
I.S. EN ISO 12736:2014
Petroleum and Natural gas Industries - wet Thermal Insulation Coatings for Pipelines, Flow Lines, Equipment and Subsea
Structures (ISO 12736:2014)
SR CEN ISO/TS 12747:2013
Petroleum and natural gas industries -- Pipeline transportation systems -- Recommended practice for pipeline life extension
(ISO/TS 12747:2011)
I.S. EN 13942:2009
Petroleum and natural gas industries - Pipeline transportation systems - Pipeline valves (ISO 14313:2007 modified)
I.S. EN 14161:2011+A1:2015
Petroleum and natural gas industries - Pipeline transportation systems (ISO 13623:2009 modified)
I.S. EN 14163:2001
Petroleum and natural gas industries - Pipeline transportation systems - Welding of pipelines (ISO 13847:2000 modified)
I.S. EN 14870-1:2011
Petroleum and natural gas industries - Induction bends, fittings and flanges for pipeline transportation systems - Part 1: Induction
bends (ISO 15590-1:2009 modified)
I.S. EN 14870-2:2004
Petroleum and natural gas industries - Induction bends, fittings and flanges for pipeline transportation systems - Part 2: Fittings
(ISO 15590-2:2003 modified)
I.S. EN 14870-3:2006
Petroleum and natural gas industries - Induction bends, fittings and flanges for pipeline transportation systems - Part 3: Flanges
(ISO 15590-3:2004, modified)
I.S. EN ISO 14723:2009
Petroleum and natural gas industries - Pipeline transportation systems - Subsea pipeline valves (ISO 14723:2009)
ISO 15589-1:2015
Petroleum and natural gas industries -- Cathodic protection of pipeline transportation systems -- Part 1: On-land pipelines
I.S. EN ISO 15589-2:2014
Petroleum, petrochemical and natural gas industries -- Cathodic protection of pipeline transportation systems -- Part 2: Offshore
pipelines (ISO 15589-2:2012)
I.S. EN ISO 16708:2006
Petroleum and natural gas industries - Pipeline transportation systems - Reliability-based limit state methods (ISO 16708:2006)
I.S. EN ISO 21329:2004
Petroleum and natural gas industries - Pipeline transportation systems - Test procedures for mechanical connectors
(ISO 21329:2004)
Petroleum Exploration and Extraction Technical Standards Committee
19
I.S. EN ISO 21809-2:2014
Petroleum and natural gas industries - External coatings for buried or submerged pipelines used in pipeline transportation systems
- Part 2: Fusion-bonded epoxy coatings (ISO 21809-2:2014)
ISO 21809-3:2008+A1:2011
Petroleum and natural gas industries -- External coatings for buried or submerged pipelines used in pipeline transportation
systems -- Part 3: Field joint coatings
ISO 21809-4:2009
Petroleum and natural gas industries -- External coatings for buried or submerged pipelines used in pipeline transportation
systems -- Part 4: Polyethylene coatings (2-layer PE)
I.S. EN ISO 21809-5:2010
Petroleum and natural gas industries - External coatings for buried or submerged pipelines used in pipeline transportation systems
- Part 5: External concrete coatings (ISO 21809-5:2010)
8.7 Onshore processing
Standards listed have been developed:
CEN/TC 12 - Materials, equipment and offshore structures for petroleum, petrochemical and natural gas industries
CEN/TC 69 – Industrial valves ISO/TC 60/SC 2 – Gears - Gear capacity calculation
ISO/TC 67/SC 4 – Drilling and production equipment
ISO/TC 67/SC 6 – Processing equipment and systems
ISO/TC 115/SC 3 – Pumps - Installation and special application
ISO/TC 118/SC 1 – Compressors and pneumatic tools, machines and equipment- Process compressors
ISO/TC 153 – Valves
ISO/TC 192 – Gas turbines
Standards applicable to onshore processing
I.S. EN ISO 3977-5:2003
Gas turbines - Procurement - Part 5: Applications for petroleum and natural gas industries (ISO 3977-5:2001)
ISO 10428:1993
Petroleum and natural gas industries -- Sucker rods (pony rods, polished rods, couplings and sub-couplings) --
Specification
ISO 10431:1993
Petroleum and natural gas industries -- Pumping units -- Specification
I.S. EN ISO 10434:2004
Bolted bonnet steel gate valves for the petroleum, petrochemical and allied industries (ISO 10434:2004)
I.S. EN ISO 10437:2003
Petroleum, petrochemical and natural gas industries - Steam turbines - Special-purpose applications (ISO 10437:2003)
I.S. EN ISO 10438-1:2007
Petroleum, petrochemical and natural gas industries - Lubrication, shaft-sealing and control-oil systems and auxiliaries -
Part 1: General requirements (ISO 10438-1:2007)
Petroleum Exploration and Extraction Technical Standards Committee
20
I.S. EN ISO 10438-2:2007
Petroleum, petrochemical and natural gas industries - Lubrication, shaft-sealing and control-oil systems and auxiliaries -
Part 2: Special-purpose oil systems (ISO 10438-2:2007)
I.S. EN ISO 10438-3:2007
Petroleum, petrochemical and natural gas industries - Lubrication, shaft-sealing and control-oil systems and auxiliaries -
Part 3: General-purpose oil systems (ISO 10438-3:2007)
I.S. EN ISO 10438-4:2007
Petroleum, petrochemical and natural gas industries - Lubrication, shaft-sealing and control-oil systems and auxiliaries -
Part 4: Self-acting gas seal support systems (ISO 10438-4:2007)
I.S. EN ISO 10439-1:2015 Petroleum, petrochemical and natural gas industries - Axial and centrifugal compressors and expander-compressors -
Part 1: General requirements (ISO 10439-1:2015)
I.S. EN ISO 10439-2:2015
Petroleum, petrochemical and natural gas industries - Axial and centrifugal compressors and expander-compressors -
Part 2: Non-integrally geared centrifugal and axial compressors (ISO 10439-2:2015)
I.S. EN ISO 10439-3:2015
Petroleum, petrochemical and natural gas industries - axial and centrifugal compressors and expander-compressors -
Part 3: Integrally geared centrifugal compressors (ISO 10439-3:2015)
I.S. EN ISO 10439-4:2015
Petroleum, petrochemical and natural gas industries - Axial and centrifugal compressors and expander-compressors -
Part 4: Expander-compressors (ISO 10439-4:2015)
I.S. EN ISO 10440-1:2007
Petroleum, petrochemical and natural gas industries - Rotary-type positive-displacement compressors - Part 1: Process
compressors (ISO 10440-1:2007)
I.S. EN ISO 10440-2:2001
Petroleum and natural gas industries - Rotary-type positive-displacement compressors - Part 2: Packaged air
compressors (oil-free) (ISO 10440-2:2001)
I.S. EN ISO 10441:2007
Petroleum, petrochemical and natural gas industries - Flexible couplings for mechanical power transmission - Special-
purpose applications (ISO 10441:2007)
I.S. EN ISO 10442:2002
Petroleum, chemical and gas service industries - Packaged, integrally geared centrifugal air compressors
(ISO 10442:2002)
I.S. EN ISO 12211:2012
Petroleum, Petrochemical and Natural gas Industries - Spiral Plate Heat Exchangers (ISO 12211:2012)
I.S. EN ISO 12212:2012
Petroleum, Petrochemical and Natural gas Industries - Hairpin-type Heat Exchangers (ISO 12212:2012)
I.S. EN ISO 13631:2002
Petroleum and natural gas industries - Packaged reciprocating gas compressors (ISO 13631:2002)
I.S. EN ISO 13691:2002
Petroleum and natural gas industries - High-speed special-purpose gear units (ISO 13691:2001)
I.S. EN ISO 13704:2007
Petroleum, petrochemical and natural gas industries - Calculation of heater-tube thickness in petroleum refineries
(ISO 13704:2007)
I.S. EN ISO 13705:2012
Petroleum, petrochemical and natural gas industries - Fired heaters for general refinery service (ISO 13705:2012)
I.S. EN ISO 13706:2011
Petroleum, petrochemical and natural gas industries - Air-cooled heat exchangers (ISO 13706:2011)
Petroleum Exploration and Extraction Technical Standards Committee
21
ISO 13707:2000
Petroleum and natural gas industries -- Reciprocating compressors
I.S. EN ISO 13709:2009
Centrifugal pumps for petroleum, petrochemical and natural gas industries (ISO 13709:2009)
I.S. EN ISO 13710:2004
Petroleum, petrochemical and natural gas industries - Reciprocating positive displacement pumps (ISO 13710:2004)
I.S. EN ISO 14691:2008
Petroleum, petrochemical and natural gas industries - Flexible couplings for mechanical power transmission - General-
purpose applications (ISO 14691:2008)
I.S. EN ISO 15547-1:2005
Petroleum, petrochemical and natural gas industries - Plate-type heat exchangers - Part 1: Plate-and-frame heat
exchangers (ISO 15547-1:2005)
I.S. EN ISO 15547-2:2005
Petroleum, petrochemical and natural gas industries - Plate-type heat exchangers - Part 2: Brazed aluminium plate-fin
heat exchangers (ISO 15547-2:2005)
S.R. CEN/TR 14549:2004
Guide to the use of ISO 15649 and ANSI/ASME B31.3 for piping in Europe in compliance with the Pressure Equipment
Directive
I.S. EN ISO 15761:2002
Steel gate, globe and check valves for sizes DN 100 and smaller, for the petroleum and natural gas industries
(ISO 15761:2002)
I.S. EN ISO 16812:2007
Petroleum, petrochemical and natural gas industries - Shell-and-tube heat exchangers (ISO 16812:2007)
I.S. EN ISO 16961:2015
Petroleum, Petrochemical and Natural gas Industries - Internal Coating and Lining of Steel Storage Tanks
(ISO 16961:2015)
I.S. EN ISO 17292:2015
Metal ball valves for petroleum, petrochemical and allied industries (ISO 17292:2015)
I.S. EN ISO 21049:2004
Pumps - Shaft sealing systems for centrifugal and rotary pumps (ISO 21049:2004)
I.S. EN ISO 23251:2007+A1:2008
Petroleum, petrochemical and natural gas industries - Pressure-relieving and depressuring systems (ISO 23251:2006)
I.S. EN ISO 24817:2015
Petroleum, petrochemical and natural gas industries - Composite repairs for pipework - Qualification and design,
installation, testing and inspection (ISO 24817:2015)
I.S. EN ISO 25457:2008
Petroleum, petrochemical and natural gas industries - Flare details for general refinery and petrochemical service
(ISO 25457:2008)
I.S. EN ISO 28300:2008
Petroleum, petrochemical and natural gas industries - Venting of atmospheric and low-pressure storage tanks
(ISO 28300:2008)
Petroleum Exploration and Extraction Technical Standards Committee
22
9 Information on each Technical Committee
The information in this section is for reference only. The Standards listed are those published by the Technical Committee and are not all utilised in the undertakings within the scope of work of the PEETSC.
9.1 ISO/TC 67 - Structure
ISO Technical Committee 67 is a large TC with a structure more complicated than other TC's due to the large scope of work and Standards covering this area. Each relevant part of the TC is addressed within this section 9.1.
9.1.1 ISO/TC 67
Title: Materials, equipment and offshore structures for petroleum, petrochemical and natural gas industries
Secretariat: NEN (Dutch National Standards Body) Secretary: Mrs. Jeannette Hofman Chairperson: Vacant ISO Central Secretariat contact: Mrs. Kirsi Silander-van Hunen Editorial Programme Manager: Mrs. Laura Mathew Creation date: 1947
The scope of ISO/TC 67 is the standardization of the materials, equipment and offshore structures used in the drilling, production, transport by pipelines and processing of liquid and gaseous hydrocarbons within the petroleum, petrochemical and natural gas industries.
Excluded from the scope are aspects of offshore structures subject to International Maritime Organization (IMO) requirements which are covered by ISO/TC 8 Ships and marine technology.
Total number of published ISO standards related to the TC and its SCs (number includes updates):
198
Number of published ISO standards under the direct responsibility of TC 67 (number includes updates):
23
(P) Participating countries: 33
(O) Observing countries: 33
Irelands membership status O- member
Sub-Committees of ISO/TC 67
TC Sub-Committee SC Title Irelands membership status
ISO/TC 67/SC 2 Pipeline transportation systems P
ISO/TC 67/SC 3 Drilling and completion fluids, and well cements -
Petroleum Exploration and Extraction Technical Standards Committee
23
ISO/TC 67/SC 4 Drilling and production equipment -
ISO/TC 67/SC 5 Casing, tubing and drill pipe -
ISO/TC 67/SC 6 Processing equipment and systems -
ISO/TC 67/SC 7 Offshore structures -
ISO/TC 67/SC 8 Arctic operations -
ISO/TC 67/SC 9 Liquefied natural gas installations and equipment -
Working Groups of ISO/TC 67
ISO/TC 67/EC/MC Executive committee and Management committee
ISO/TC 67/WG 2 Conformity assessment
TC 67/WG 4 Reliability Engineering and technology
TC 67/WG 5 Aluminium alloy pipes
TC 67/WG 7 Corrosion resistant materials
TC 67/WG 8 Materials, corrosion control, welding and jointing, and non-destructive examination (NDE)
TC 67/WG 10 Liquefied Natural Gas (LNG) installations and equipment
TC 67/WG 11 Coating and lining of structures and equipment
TC 67/WG 12 CO2 aspects
TC 67/JWG 13 Joint ISO/TC 67 - ISO TC 8/SC8 WG; Cryogenic spillage
Standards published by ISO /TC 67
ISO/TR 12489:2013 Petroleum, petrochemical and natural gas industries -- Reliability modelling and calculation of safety systems
ISO 13085:2014 Petroleum and natural gas industries -- Aluminium alloy pipe for use as tubing for wells
ISO 13879:1999 Petroleum and natural gas industries -- Content and drafting of a functional specification
ISO 13880:1999 Petroleum and natural gas industries -- Content and drafting of a technical specification
ISO/TR 13881:2000 Petroleum and natural gas industries -- Classification and conformity assessment of products, processes and services
ISO 14224:2006 Petroleum, petrochemical and natural gas industries -- Collection and exchange of reliability and maintenance data for
Petroleum Exploration and Extraction Technical Standards Committee
24
equipment
ISO 15156-1:2015 Petroleum and natural gas industries -- Materials for use in H2S-containing environments in oil and gas production -- Part 1: General principles for selection of cracking-resistant materials
ISO 15156-2:2015 Petroleum and natural gas industries -- Materials for use in H2S-containing environments in oil and gas production -- Part 2: Cracking-resistant carbon and low-alloy steels, and the use of cast irons
ISO 15156-3:2015 Petroleum and natural gas industries -- Materials for use in H2S-containing environments in oil and gas production -- Part 3: Cracking-resistant CRAs (corrosion-resistant alloys) and other alloys
ISO 15546:2011 Petroleum and natural gas industries -- Aluminium alloy drill pipe
ISO 15663-1:2000 Petroleum and natural gas industries -- Life cycle costing -- Part 1: Methodology
ISO 15663-2:2001 Petroleum and natural gas industries -- Life-cycle costing -- Part 2: Guidance on application of methodology and calculation methods
ISO 15663-3:2001 Petroleum and natural gas industries -- Life-cycle costing -- Part 3: Implementation guidelines
ISO 16961:2015 Petroleum, petrochemical and natural gas industries -- Internal coating and lining of steel storage tanks
ISO 17945:2015 Petroleum, petrochemical and natural gas industries -- Metallic materials resistant to sulfide stress cracking in corrosive petroleum refining environments
ISO/TS 17969:2015 Petroleum, petrochemical and natural gas industries -- Guidelines on competency for personnel
ISO 20312:2011 Petroleum and natural gas industries -- Design and operating limits of drill strings with aluminium alloy components
ISO 20815:2008 Petroleum, petrochemical and natural gas industries -- Production assurance and reliability management
ISO 21457:2010 Petroleum, petrochemical and natural gas industries -- Materials selection and corrosion control for oil and gas production systems
ISO 23936-1:2009 Petroleum, petrochemical and natural gas industries -- Non-metallic materials in contact with media related to oil and gas production -- Part 1: Thermoplastics
ISO 23936-2:2011 Petroleum, petrochemical and natural gas industries -- Non-metallic materials in contact with media related to oil and gas production -- Part 2: Elastomers
ISO 27627:2014 Petroleum and natural gas industries -- Aluminium alloy drill pipe thread connection gauging
ISO/TS 29001:2010 Petroleum, petrochemical and natural gas industries -- Sector-specific quality management systems -- Requirements for product and service supply organizations
Petroleum Exploration and Extraction Technical Standards Committee
25
9.1.2 ISO/TC 67/SC 2
Title: Pipeline transportation systems
Secretariat: UNI (Italian National Standards Body) Twinned secretariat: SAC Secretary: Mr Giuliano Corbella Twinned secretary: Mr. Changyi Qin Chairperson: Mr. Denis Tikhomirov until end 2015 ISO Central Secretariat contact: Mrs. Kirsi Silander Editorial Programme Manager(s): Mrs. Laura Mathew
Number of published ISO standards under the direct responsibility of TC 67/SC 2 (number includes updates):
22
(P) Participating countries: 28
(O) Observing countries: 10
Irelands membership status P
Standards published by ISO/TC 67/SC 2
ISO 3183:2012 Petroleum and natural gas industries -- Steel pipe for pipeline transportation systems
ISO 12490:2011 Petroleum and natural gas industries -- Mechanical integrity and sizing of actuators and mounting kits for pipeline valves
ISO 12736:2014 Petroleum and natural gas industries -- Wet thermal insulation coatings for pipelines, flow lines, equipment and subsea structures
ISO/TS 12747:2011 Petroleum and natural gas industries -- Pipeline transportation systems -- Recommended practice for pipeline life extension
ISO 13623:2009 Petroleum and natural gas industries -- Pipeline transportation systems
ISO 13847:2013 Petroleum and natural gas industries -- Pipeline transportation systems -- Welding of pipelines
ISO 14313:2007 Petroleum and natural gas industries -- Pipeline transportation systems -- Pipeline valves
ISO 14313:2007/Cor 1:2009
ISO 14723:2009 Petroleum and natural gas industries -- Pipeline transportation systems -- Subsea pipeline valves
ISO 15589-1:2015 Petroleum and natural gas industries -- Cathodic protection of pipeline transportation systems -- Part 1: On-land pipelines
ISO 15589-2:2012 Petroleum, petrochemical and natural gas industries -- Cathodic protection of pipeline transportation systems -- Part 2: Offshore pipelines
ISO 15590-1:2009 Petroleum and natural gas industries -- Induction bends, fittings and flanges for pipeline transportation systems -- Part 1: Induction bends
Petroleum Exploration and Extraction Technical Standards Committee
26
ISO 15590-2:2003 Petroleum and natural gas industries -- Induction bends, fittings and flanges for pipeline transportation systems -- Part 2: Fittings
ISO 15590-3:2004 Petroleum and natural gas industries -- Induction bends, fittings and flanges for pipeline transportation systems -- Part 3: Flanges
ISO 16708:2006 Petroleum and natural gas industries -- Pipeline transportation systems -- Reliability-based limit state methods
ISO 21329:2004 Petroleum and natural gas industries -- Pipeline transportation systems -- Test procedures for mechanical connectors
ISO 21809-1:2011 Petroleum and natural gas industries -- External coatings for buried or submerged pipelines used in pipeline transportation systems -- Part 1: Polyolefin coatings (3-layer PE and 3-layer PP)
ISO 21809-2:2014 Petroleum and natural gas industries -- External coatings for buried or submerged pipelines used in pipeline transportation systems -- Part 2: Fusion-bonded epoxy coatings
ISO 21809-3:2008 Petroleum and natural gas industries -- External coatings for buried or submerged pipelines used in pipeline transportation systems -- Part 3: Field joint coatings
ISO 21809-3:2008/Amd 1:2011
ISO 21809-4:2009 Petroleum and natural gas industries -- External coatings for buried or submerged pipelines used in pipeline transportation systems -- Part 4: Polyethylene coatings (2-layer PE)
ISO 21809-5:2010 Petroleum and natural gas industries -- External coatings for buried or submerged pipelines used in pipeline transportation systems -- Part 5: External concrete coatings
9.1.3 ISO/TC 67/SC 3
Title: Drilling and completion fluids, and well cements
Secretariat: SN (Norwegian National Standards Body) Secretary: Ms Inghild Kaarstad Chairperson: Vacant ISO Central Secretariat contact: Mrs. Kirsi Silander - van Hunen Editorial Programme Manager(s): Mrs. Laura Mathew
Number of published ISO standards under the direct responsibility of TC 67/SC 3 (number includes updates):
28
(P) Participating countries: 13
(O) Observing countries: 8
Irelands membership status -
Standards published by ISO/TC 67/SC 3
ISO 10414-1:2008 Petroleum and natural gas industries -- Field testing of drilling fluids -- Part 1: Water-based fluids
Petroleum Exploration and Extraction Technical Standards Committee
27
ISO 10414-2:2011 Petroleum and natural gas industries -- Field testing of drilling fluids -- Part 2: Oil-based fluids
ISO 10416:2008 Petroleum and natural gas industries -- Drilling fluids -- Laboratory testing
ISO 10426-1:2009 Petroleum and natural gas industries -- Cements and materials for well cementing -- Part 1: Specification
ISO 10426-1:2009/Cor 1:2010
ISO 10426-1:2009/Cor 2:2012
ISO 10426-2:2003 Petroleum and natural gas industries -- Cements and materials for well cementing -- Part 2: Testing of well cements
ISO 10426-2:2003/Cor 1:2006
ISO 10426-2:2003/Amd 1:2005 Water-wetting capability testing
ISO 10426-3:2003 Petroleum and natural gas industries -- Cements and materials for well cementing -- Part 3: Testing of deepwater well cement formulations
ISO 10426-4:2004 Petroleum and natural gas industries -- Cements and materials for well cementing -- Part 4: Preparation and testing of foamed cement slurries at atmospheric pressure
ISO 10426-5:2004 Petroleum and natural gas industries -- Cements and materials for well cementing -- Part 5: Determination of shrinkage and expansion of well cement formulations at atmospheric pressure
ISO 10426-6:2008 Petroleum and natural gas industries -- Cements and materials for well cementing -- Part 6: Methods for determining the static gel strength of cement formulations
ISO 10427-1:2001 Petroleum and natural gas industries -- Equipment for well cementing -- Part 1: Casing bow-spring centralizers
ISO 10427-2:2004 Petroleum and natural gas industries -- Equipment for well cementing -- Part 2: Centralizer placement and stop-collar testing
ISO 10427-3:2003 Petroleum and natural gas industries -- Equipment for well cementing -- Part 3: Performance testing of cementing float equipment
ISO 13500:2008 Petroleum and natural gas industries -- Drilling fluid materials -- Specifications and tests
ISO 13500:2008/Cor 1:2009
ISO 13500:2008/Amd 1:2010 Barite 4,1
ISO 13501:2011 Petroleum and natural gas industries -- Drilling fluids -- Processing equipment evaluation
ISO 13503-1:2011 Petroleum and natural gas industries -- Completion fluids and materials -- Part 1: Measurement of viscous properties of completion fluids
ISO 13503-2:2006 Petroleum and natural gas industries -- Completion fluids and materials -- Part 2: Measurement of properties of proppants used in hydraulic fracturing and gravel-packing operations
ISO 13503-2:2006/Amd 1:2009 Addition of Annex B: Proppand specification
ISO 13503-3:2005 Petroleum and natural gas industries -- Completion fluids and materials -- Part 3: Testing of heavy brines
Petroleum Exploration and Extraction Technical Standards Committee
28
ISO 13503-3:2005/Cor 1:2006
ISO 13503-4:2006 Petroleum and natural gas industries -- Completion fluids and materials -- Part 4: Procedure for measuring stimulation and gravel-pack fluid leak off under static conditions
ISO 13503-5:2006 Petroleum and natural gas industries -- Completion fluids and materials -- Part 5: Procedures for measuring the long-term conductivity of proppants
ISO 13503-6:2014 Petroleum and natural gas industries -- Completion fluids and materials -- Part 6: Procedure for measuring leakoff of completion fluids under dynamic conditions
9.1.4 ISO/TC 67/SC 4
Title: Drilling and production equipment
Secretariat: ANSI Secretary: Mr. Ed Barrett Chairperson: Mr Oliver C. Moghissi until end 2016 ISO Central Secretariat contact: Mrs. Kirsi Silander-van Hunen Editorial Programme Manager(s): Mrs. Laura Mathew
Number of published ISO standards under the direct responsibility of TC 67/SC 4 (number includes updates):
52
(P) Participating countries: 16
(O) Observing countries: 12
Irelands membership status -
Standards published by ISO/TC 67/SC 4
ISO 10407:1993 Petroleum and natural gas industries -- Drilling and production equipment -- Drill stem design and operating limits
ISO 10407-2:2008 Petroleum and natural gas industries -- Rotary drilling equipment -- Part 2: Inspection and classification of used drill stem elements
ISO 10407-2:2008/Cor 1:2009
ISO 10417:2004 Petroleum and natural gas industries -- Subsurface safety valve systems -- Design, installation, operation and redress
ISO 10423:2009 Petroleum and natural gas industries -- Drilling and production equipment -- Wellhead and christmas tree equipment
ISO 10424-1:2004 Petroleum and natural gas industries -- Rotary drilling equipment -- Part 1: Rotary drill stem elements
ISO 10424-2:2007 Petroleum and natural gas industries -- Rotary drilling equipment -- Part 2: Threading and gauging of rotary shouldered thread connections
ISO 10428:1993 Petroleum and natural gas industries -- Sucker rods (pony rods, polished rods, couplings and sub-couplings) --
Petroleum Exploration and Extraction Technical Standards Committee
29
Specification
ISO 10431:1993 Petroleum and natural gas industries -- Pumping units -- Specification
ISO 10432:2004 Petroleum and natural gas industries -- Downhole equipment -- Subsurface safety valve equipment
ISO 13354:2014 Petroleum and natural gas industries -- Drilling and production equipment -- Shallow gas diverter equipment
ISO 13533:2001 Petroleum and natural gas industries -- Drilling and production equipment -- Drill-through equipment
ISO 13533:2001/Cor 1:2005
ISO 13534:2000 Petroleum and natural gas industries -- Drilling and production equipment -- Inspection, maintenance, repair and remanufacture of hoisting equipment
ISO 13535:2000 Petroleum and natural gas industries -- Drilling and production equipment -- Hoisting equipment
ISO 13624-1:2009 Petroleum and natural gas industries -- Drilling and production equipment -- Part 1: Design and operation of marine drilling riser equipment
ISO/TR 13624-2:2009 Petroleum and natural gas industries -- Drilling and production equipment -- Part 2: Deepwater drilling riser methodologies, operations, and integrity technical report
ISO 13625:2002 Petroleum and natural gas industries -- Drilling and production equipment -- Marine drilling riser couplings
ISO 13626:2003 Petroleum and natural gas industries -- Drilling and production equipment -- Drilling and well-servicing structures
ISO 13628-1:2005 Petroleum and natural gas industries -- Design and operation of subsea production systems -- Part 1: General requirements and recommendations
ISO 13628-1:2005/Amd 1:2010 Revised Clause 6
ISO 13628-2:2006 Petroleum and natural gas industries -- Design and operation of subsea production systems -- Part 2: Unbonded flexible pipe systems for subsea and marine applications
ISO 13628-2:2006/Cor 1:2009
ISO 13628-3:2000 Petroleum and natural gas industries -- Design and operation of subsea production systems -- Part 3: Through flowline (TFL) systems
ISO 13628-4:2010 Petroleum and natural gas industries -- Design and operation of subsea production systems -- Part 4: Subsea wellhead and tree equipment
ISO 13628-4:2010/Cor 1:2011
ISO 13628-5:2009 Petroleum and natural gas industries -- Design and operation of subsea production systems -- Part 5: Subsea umbilicals
ISO 13628-6:2006 Petroleum and natural gas industries -- Design and operation of subsea production systems -- Part 6: Subsea production control systems
ISO 13628-7:2005 Petroleum and natural gas industries -- Design and operation of subsea production systems -- Part 7: Completion/workover riser systems
ISO 13628-8:2002 Petroleum and natural gas industries -- Design and operation of subsea production systems -- Part 8: Remotely Operated
Petroleum Exploration and Extraction Technical Standards Committee
30
Vehicle (ROV) interfaces on subsea production systems
ISO 13628-8:2002/Cor 1:2005
ISO 13628-9:2000 Petroleum and natural gas industries -- Design and operation of subsea production systems -- Part 9: Remotely Operated Tool (ROT) intervention systems
ISO 13628-10:2005 Petroleum and natural gas industries -- Design and operation of subsea production systems -- Part 10: Specification for bonded flexible pipe
ISO 13628-11:2007 Petroleum and natural gas industries -- Design and operation of subsea production systems -- Part 11: Flexible pipe systems for subsea and marine applications
ISO 13628-11:2007/Cor 1:2008
ISO 13628-15:2011 Petroleum and natural gas industries -- Design and operation of subsea production systems -- Part 15: Subsea structures and manifolds
ISO 14310:2008 Petroleum and natural gas industries -- Downhole equipment -- Packers and bridge plugs
ISO 14693:2003 Petroleum and natural gas industries -- Drilling and well-servicing equipment
ISO 15136-1:2009 Petroleum and natural gas industries -- Progressing cavity pump systems for artificial lift -- Part 1: Pumps
ISO 15136-2:2006 Petroleum and natural gas industries -- Progressing cavity pump systems for artificial lift -- Part 2: Surface-drive systems
ISO 16070:2005 Petroleum and natural gas industries -- Downhole equipment -- Lock mandrels and landing nipples
ISO/TS 16530-2:2014 Well integrity -- Part 2: Well integrity for the operational phase
ISO 17078-1:2004 Petroleum and natural gas industries -- Drilling and production equipment -- Part 1: Side-pocket mandrels
ISO 17078-1:2004/Amd 1:2010
ISO 17078-2:2007 Petroleum and natural gas industries -- Drilling and production equipment -- Part 2: Flow-control devices for side-pocket mandrels
ISO 17078-2:2007/Cor 1:2009
ISO 17078-3:2009 Petroleum and natural gas industries -- Drilling and production equipment -- Part 3: Running tools, pulling tools and kick-over tools and latches for side-pocket mandrels
ISO 17078-4:2010 Petroleum and natural gas industries -- Drilling and production equipment -- Part 4: Practices for side-pocket mandrels and related equipment
ISO 17824:2009 Petroleum and natural gas industries -- Downhole equipment -- Sand screens
ISO 28781:2010 Petroleum and natural gas industries -- Drilling and production equipment --Subsurface barrier valves and related equipment
Petroleum Exploration and Extraction Technical Standards Committee
31
9.1.5 ISO/TC 67/SC 5
Title: Casing, tubing and drill pipe
Secretariat: JISC (Japan Iron and Steel Federation) Secretary: Mr. Tsunehiro Ise Chairperson: Mr Tsuneo Murase until end 2019 ISO Central Secretariat contact: Mrs. Kirsi Silander -van Hunen Editorial Programme Manager(s): Mrs. Laura Mathew
Number of published ISO standards under the direct responsibility of TC 67/SC 5 (number includes updates):
11
(P) Participating countries: 20
(O) Observing countries: 10
Irelands membership status -
Standards published by ISO/TC 67/SC 5
ISO/TR 10400:2007 Petroleum and natural gas industries -- Equations and calculations for the properties of casing, tubing, drill pipe and line pipe used as casing or tubing
ISO 10405:2000 Petroleum and natural gas industries -- Care and use of casing and tubing
ISO 11960:2014 Petroleum and natural gas industries -- Steel pipes for use as casing or tubing for wells
ISO 11961:2008 Petroleum and natural gas industries -- Steel drill pipe
ISO 11961:2008/Cor 1:2009
ISO/PAS 12835:2013 Qualification of casing connections for thermal wells
ISO 13678:2010 Petroleum and natural gas industries -- Evaluation and testing of thread compounds for use with casing, tubing, line pipe and drill stem elements
ISO 13679:2002 Petroleum and natural gas industries -- Procedures for testing casing and tubing connections
ISO 13680:2010 Petroleum and natural gas industries -- Corrosion-resistant alloy seamless tubes for use as casing, tubing and coupling stock -- Technical delivery conditions
ISO 15463:2003 Petroleum and natural gas industries -- Field inspection of new casing, tubing and plain-end drill pipe
ISO 15463:2003/Cor 1:2009
Petroleum Exploration and Extraction Technical Standards Committee
32
9.1.6 ISO/TC 67/SC 6
Title: Processing equipment and systems
Secretariat: AFNOR (French National Standards Body) Secretary: M Nicolas Marcq Chairperson: M. Joël Fort (France) until end 2017 ISO Central Secretariat contact: Mrs. Kirsi Silander -van Hunen
Number of published ISO standards under the direct responsibility of TC 67/SC 6 (number includes updates):
40
(P) Participating countries: 17
(O) Observing countries: 11
Irelands membership status -
Standards published by ISO/TC 67/SC 6
ISO 10418:2003 Petroleum and natural gas industries -- Offshore production installations -- Analysis, design, installation and testing of basic surface process safety systems
ISO 10418:2003/Cor 1:2008
ISO 10437:2003 Petroleum, petrochemical and natural gas industries -- Steam turbines -- Special-purpose applications
ISO 10438-1:2007 Petroleum, petrochemical and natural gas industries -- Lubrication, shaft-sealing and control-oil systems and auxiliaries -- Part 1: General requirements
ISO 10438-2:2007 Petroleum, petrochemical and natural gas industries -- Lubrication, shaft-sealing and control-oil systems and auxiliaries -- Part 2: Special-purpose oil systems
ISO 10438-3:2007 Petroleum, petrochemical and natural gas industries -- Lubrication, shaft-sealing and control-oil systems and auxiliaries -- Part 3: General-purpose oil systems
ISO 10438-4:2007 Petroleum, petrochemical and natural gas industries -- Lubrication, shaft-sealing and control-oil systems and auxiliaries -- Part 4: Self-acting gas seal support systems
ISO 10441:2007 Petroleum, petrochemical and natural gas industries -- Flexible couplings for mechanical power transmission -- Special-purpose applications
ISO 12211:2012 Petroleum, petrochemical and natural gas industries -- Spiral plate heat exchangers
ISO 12212:2012 Petroleum, petrochemical and natural gas industries -- Hairpin-type heat exchangers
ISO 13702:2015 Petroleum and natural gas industries -- Control and mitigation of fires and explosions on offshore production installations -- Requirements and guidelines
ISO 13703:2000 Petroleum and natural gas industries -- Design and installation of piping systems on offshore production platforms
ISO 13703:2000/Cor 1:2002
Petroleum Exploration and Extraction Technical Standards Committee
33
ISO 13704:2007 Petroleum, petrochemical and natural gas industries -- Calculation of heater-tube thickness in petroleum refineries
ISO 13704:2007/Cor 1:2008
ISO 13705:2012 Petroleum, petrochemical and natural gas industries - Fired heaters for general refinery service
ISO 13706:2011 Petroleum, petrochemical and natural gas industries -- Air-cooled heat exchangers
ISO 14691:2008 Petroleum, petrochemical and natural gas industries -- Flexible couplings for mechanical power transmission -- General-purpose applications
ISO 14692-1:2002 Petroleum and natural gas industries -- Glass-reinforced plastics (GRP) piping -- Part 1: Vocabulary, symbols, applications and materials
ISO 14692-2:2002 Petroleum and natural gas industries -- Glass-reinforced plastics (GRP) piping -- Part 2: Qualification and manufacture
ISO 14692-2:2002/Cor 1:2005
ISO 14692-3:2002 Petroleum and natural gas industries -- Glass-reinforced plastics (GRP) piping -- Part 3: System design
ISO 14692-3:2002/Cor 1:2005
ISO 14692-4:2002 Petroleum and natural gas industries -- Glass-reinforced plastics (GRP) piping -- Part 4: Fabrication, installation and operation
ISO 14692-4:2002/Cor 1:2006
ISO 15138:2007 Petroleum and natural gas industries -- Offshore production installations -- Heating, ventilation and air-conditioning
ISO 15544:2000/Amd 1:2009 Petroleum and natural gas industries -- Offshore production installations -- Requirements and guidelines for emergency response
ISO 15547-1:2005 Petroleum, petrochemical and natural gas industries -- Plate-type heat exchangers -- Part 1: Plate-and-frame heat exchangers
ISO 15547-2:2005 Petroleum, petrochemical and natural gas industries -- Plate-type heat exchangers -- Part 2: Brazed aluminium plate-fin heat exchangers
ISO 15649:2001 Petroleum and natural gas industries -- Piping
ISO 16812:2007 Petroleum, petrochemical and natural gas industries -- Shell-and-tube heat exchangers
ISO 17776:2000 Petroleum and natural gas industries -- Offshore production installations -- Guidelines on tools and techniques for hazard identification and risk assessment
ISO/TS 24817:2015 Petroleum, petrochemical and natural gas industries -- Composite repairs for pipework -- Qualification and design, installation, testing and inspection
ISO 25457:2008 Petroleum, petrochemical and natural gas industries -- Flare details for general refinery and petrochemical service
ISO/TS 27469:2010 Petroleum, petrochemical and natural gas industries - Method of test for fire dampers
ISO 27509:2012 Petroleum and natural gas industries -- Compact flanged connections with IX seal ring
Petroleum Exploration and Extraction Technical Standards Committee
34
ISO 28300:2008 Petroleum, petrochemical and natural gas industries -- Venting of atmospheric and low-pressure storage tanks
ISO 28300:2008/Cor 1:2009
9.1.7 ISO/TC 67/SC 7
Title: Offshore structures
Secretariat: BSI (UK National Standards Body) Secretary: Dr. Charles A. Whitlock Chairperson: Mr. Philip Smedley (United Kingdom) until end 2016 ISO Central Secretariat contact: Mrs. Kirsi Silander-van Hunen Editorial Programme Manager(s): Mrs. Laura Mathew
Number of published ISO standards under the direct responsibility of TC 67/SC 7 (number includes updates):
17
(P) Participating countries: 23
(O) Observing countries: 9
Irelands membership status -
Standards published by ISO/TC 67/SC 7
ISO 19900:2013 Petroleum and natural gas industries -- General requirements for offshore structures
ISO 19901-1:2015 Petroleum and natural gas industries -- Specific requirements for offshore structures -- Part 1: Metocean design and operating considerations
ISO 19901-2:2004 Petroleum and natural gas industries -- Specific requirements for offshore structures -- Part 2: Seismic design procedures and criteria
ISO 19901-3:2014 Petroleum and natural gas industries -- Specific requirements for offshore structures -- Part 3: Topsides structure
ISO 19901-4:2003 Petroleum and natural gas industries -- Specific requirements for offshore structures -- Part 4: Geotechnical and foundation design considerations
ISO 19901-5:2003 Petroleum and natural gas industries -- Specific requirements for offshore structures -- Part 5: Weight control during engineering and construction
ISO 19901-6:2009 Petroleum and natural gas industries -- Specific requirements for offshore structures -- Part 6: Marine operations
ISO 19901-6:2009/Cor 1:2011
ISO 19901-7:2005 Petroleum and natural gas industries -- Specific requirements for offshore structures -- Part 7: Stationkeeping systems for floating offshore structures and mobile offshore units
ISO 19901-8:2014 Petroleum and natural gas industries -- Specific requirements for offshore structures -- Part 8: Marine soil investigations
ISO 19902:2007
Petroleum Exploration and Extraction Technical Standards Committee
35
Petroleum and natural gas industries -- Fixed steel offshore structures
ISO 19902:2007/Amd 1:2013
ISO 19903:2006 Petroleum and natural gas industries -- Fixed concrete offshore structures
ISO 19904-1:2006 Petroleum and natural gas industries -- Floating offshore structures -- Part 1: Monohulls, semi-submersibles and spars
ISO 19905-1:2012 Petroleum and natural gas industries -- Site-specific assessment of mobile offshore units -- Part 1: Jack-ups
ISO/TR 19905-2:2012 Petroleum and natural gas industries -- Site-specific assessment of mobile offshore units -- Part 2: Jack-ups commentary and detailed sample calculation
ISO 19906:2010 Petroleum and natural gas industries -- Arctic offshore structures
9.1.8 ISO/TC 67/SC 8
Title: Arctic operations
Secretariat: GOST R (Russian Federation National Standards Body) Secretary: Mrs. Liudmila Zalevskaya Chairperson: Mr. Mikhail Rusakov until end 2017 ISO Central Secretariat contact: Mrs. Kirsi Silander-van Hunen Editorial Programme Manager(s): Mrs. Laura Mathew Creation date: 2011
Number of published ISO standards under the direct responsibility of TC 67/SC 7 (number includes updates):
0
(P) Participating countries: 12
(O) Observing countries: 3
Irelands membership status -
This Sub-Committee has not yet published any standards.
Petroleum Exploration and Extraction Technical Standards Committee
36
9.1.9 ISO/TC 67/SC 9
Title: Liquefied natural gas installations and equipment
Secretariat: AFNOR (French National Standards Body) Secretary: M. Christophe Erhel Chairperson: M. Max Nussbaum until end 2020 ISO Central Secretariat contact: Mrs. Kirsi Silander-van Hunen Editorial Programme Manager(s): Mrs. Laura Mathew Creation date: 2015
Number of published ISO standards under the direct responsibility of TC 67/SC 7 (number includes updates):
5
(P) Participating countries: 14
(O) Observing countries: 2
Irelands membership status -
Standards published by ISO/TC 67/SC 9
ISO/TS 16901:2015 Guidance on performing risk assessment in the design of onshore LNG installations including the ship/shore interface
ISO 16903:2015 Petroleum and natural gas industries -- Characteristics of LNG, influencing the design, and material selection
ISO/TR 17177:2015 Petroleum and natural gas industries -- Guidelines for the marine interfaces of hybrid LNG terminals
ISO/TS 18683:2015 Guidelines for systems and installations for supply of LNG as fuel to ships
ISO 28460:2010 Petroleum and natural gas industries -- Installation and equipment for liquefied natural gas -- Ship-to-shore interface and port operations
9.2 ISO/TC 60
Title: Gears
Secretariat: ANSI Secretary: Mr. Amir Aboutaleb Chairperson: Mr. Jens Demtröder ISO Central Secretariat contact: M. Pierre-Charles Bazin de Caix Creation date: 1947
The Scope ISO/TC 60 is the standardization in the field of gears, including terminology, nominal dimensions, tolerances, and tools for manufacturing and control.
Total number of published ISO standards related to the TC and its SCs (number includes updates):
63
Petroleum Exploration and Extraction Technical Standards Committee
37
Number of published ISO standards under the direct responsibility of TC 60 (number includes updates):
25
(P) Participating countries: 14
(O) Observing countries: 23
Irelands membership status -
Subcommittees of ISO/TC 60
ISO/TC 60/SC 1 Nomenclature and wormgearing
ISO/TC 60/SC 2 Gear capacity calculation
Working Groups of ISO/TC 60
ISO/TC 60/JWG 1 Joint ISO/TC 60-IEC/TC 88 WG: Wind turbine gearboxes
ISO/TC 60/WG 2 Accuracy of gears
Standards published by ISO/TC 60/SC 2
ISO 6336-1:2006
Calculation of load capacity of spur and helical gears -- Part 1: Basic principles, introduction and general influence factors
ISO 6336-1:2006/Cor 1:2008
ISO 6336-2:2006
Calculation of load capacity of spur and helical gears -- Part 2: Calculation of surface durability (pitting)
ISO 6336-2:2006/Cor 1:2008
ISO 6336-3:2006
Calculation of load capacity of spur and helical gears -- Part 3: Calculation of tooth bending strength
ISO 6336-3:2006/Cor 1:2008
ISO 6336-5:2003
Calculation of load capacity of spur and helical gears -- Part 5: Strength and quality of materials
ISO 6336-6:2006
Calculation of load capacity of spur and helical gears -- Part 6: Calculation of service life under variable load
ISO 6336-6:2006/Cor 1:2007
ISO 9083:2001
Calculation of load capacity of spur and helical gears -- Application to marine gears
ISO 9085:2002
Calculation of load capacity of spur and helical gears -- Application for industrial gears
ISO 10300-1:2014
Calculation of load capacity of bevel gears -- Part 1: Introduction and general influence factors
ISO 10300-2:2014
Petroleum Exploration and Extraction Technical Standards Committee
38
Calculation of load capacity of bevel gears -- Part 2: Calculation of surface durability (pitting)
ISO 10300-3:2014
Calculation of load capacity of bevel gears -- Part 3: Calculation of tooth root strength
ISO 13691:2001
Petroleum and natural gas industries -- High-speed special-purpose gear units
ISO 14104:2014
Gears -- Surface temper etch inspection after grinding, chemical method
ISO/TR 14179-1:2001
Gears -- Thermal capacity -- Part 1: Rating gear drives with thermal equilibrium at 95 °C sump temperature
ISO/TR 14179-2:2001
Gears -- Thermal capacity -- Part 2: Thermal load-carrying capacity
ISO 14635-1:2000
Gears -- FZG test procedures -- Part 1: FZG test method A/8,3/90 for relative scuffing load-carrying capacity of oils
ISO 14635-2:2004
Gears -- FZG test procedures -- Part 2: FZG step load test A10/16, 6R/120 for relative scuffing load-carrying capacity of
high EP oils
ISO 14635-3:2005
Gears -- FZG test procedures -- Part 3: FZG test method A/2, 8/50 for relative scuffing load-carrying capacity and wear
characteristics of semifluid gear greases
ISO/TR 15144-1:2014
Calculation of micropitting load capacity of cylindrical spur and helical gears -- Part 1: Introduction and basic principles
ISO/TR 15144-2:2014
Calculation of micropitting load capacity of cylindrical spur and helical gears -- Part 2: Examples of calculation for
micropitting
ISO/TR 18792:2008
Lubrication of industrial gear drives
ISO/TR 22849:2011
Design recommendations for bevel gears
ISO 23509:2006
Bevel and hypoid gear geometry
Petroleum Exploration and Extraction Technical Standards Committee
39
9.3 ISO/TC 115
Title: Pumps
Secretariat: AFNOR (French National Standards Body) Secretary: Mme. Sara Mélique Chairperson: M. Robert Dodane until end 2016 ISO Central Secretariat contact: Mrs. Kirsi Silander-van Hunen Editorial Programme Manager(s): Mrs. Laura MathewCreation date: 1964
The scope of ISO/TC 115 is the standardization in the field of pumps; including:
dimensions and technical specifications,
test methods and conditions of acceptance for rotodynamic and positive displacement pumps for
all liquids, including complete pumping installations,
installations and special applications, as well as rotodynamic mixers for waste water
Total number of published ISO standards related to the TC and its SCs (number includes updates):
25
Number of published ISO standards under the direct responsibility of TC 115 (number includes updates):
5
(P) Participating countries: 21
(O) Observing countries: 19
Irelands membership status -
Subcommittees of ISO/TC 115
Subcommittee Subcommittee title Irelands membership status
TC 115/SC 1 Dimensions and technical specifications of pumps -
TC 115/SC 2 Methods of measurement and testing -
TC 115/SC 3 Installation and special application -
Standards published by ISO/TC 115/SC 3
ISO 13709:2009 Centrifugal pumps for petroleum, petrochemical and natural gas industries
ISO 13710:2004 Petroleum, petrochemical and natural gas industries -- Reciprocating positive displacement pumps
ISO/TR 17766:2005 Centrifugal pumps handling viscous liquids -- Performance corrections
ISO 21049:2004 Pumps -- Shaft sealing systems for centrifugal and rotary pumps
Petroleum Exploration and Extraction Technical Standards Committee
40
9.4 ISO/TC 118
Title: Compressors and pneumatic tools, machines and equipment
Secretariat: SIS Secretary: Ms Lena Fagervall Chairperson: Mrs. Jenny Buck (United Kingdom) until end 2016 ISO Central Secretariat contact: Mrs. Kirsi Silander-van Hunen Editorial Programme Manager(s): Mrs. Laura Mathew Creation date: 1965
Scope of ISO/TC 118:
Standardization in the field of:
air compressors;
compressors for the process, petroleum, chemical and gas industry services;
pneumatic tools and machines;
compressed air purity specification and compressed air treatment equipment.
Excluded from the scope are pneumatic tool shanks and tool fitting dimensions, as they fall within the scope of ISO/TC 29 Small tools.
Total number of published ISO standards related to the TC and its SCs (number includes updates):
73
(P) Participating countries: 12
(O) Observing countries: 24
Irelands membership status -
Subcommittees of ISO/TC 118
Subcommittees of ISO/TC 118
Subcommittee title Irelands membership status
TC 118/SC 1 Process compressors -
TC 118/SC 3 Pneumatic tools and machines -
TC 118/SC 4 Compressed air purity specification and compressed air treatment equipment
-
TC 118/SC 6 Air compressors and compressed air systems -
There are no Working Groups within ISO/TC 118.
Standards published by ISO/TC 118/SC 1
ISO 5389:2005
Petroleum Exploration and Extraction Technical Standards Committee
41
Turbocompressors -- Performance test code
ISO 10439-1:2015 Petroleum, petrochemical and natural gas industries -- Axial and centrifugal compressors and expander-compressors -- Part 1: General requirements
ISO 10439-2:2015 Petroleum, petrochemical and natural gas industries -- Axial and centrifugal compressors and expander-compressors -- Part 2: Non-integrally geared centrifugal and axial compressors
ISO 10439-3:2015 Petroleum, petrochemical and natural gas industries -- Axial and centrifugal compressors and expander-compressors -- Part 3: Integrally geared centrifugal compressors
ISO 10439-4:2015 Petroleum, petrochemical and natural gas industries -- Axial and centrifugal compressors and expander-compressors -- Part 4: Expander-compressors
ISO 10440-1:2007 Petroleum, petrochemical and natural gas industries -- Rotary-type positive-displacement compressors -- Part 1: Process compressors
ISO 10440-2:2001 Petroleum and natural gas industries -- Rotary-type positive-displacement compressors -- Part 2: Packaged air compressors (oil-free)
ISO 10442:2002 Petroleum, chemical and gas service industries -- Packaged, integrally geared centrifugal air compressors
ISO 13631:2002 Petroleum and natural gas industries -- Packaged reciprocating gas compressors
9.5 ISO/TC 153
Title: Valves
Secretariat: AFNOR (French National Standards Body) Secretary: Mme Hélène Cros Chairperson: M. Alexandre Popa until end 2016 ISO Central Secretariat contact: Mme Hélène Cros Editorial Programme Manager(s): Ms Nicola Perou Creation date: 1971
The scope of work for ISO/TC 153 is the standardization in the field of industrial valves and steam traps. The standardization to include parameters covering interchangeability, valve mating details for actuator mounting, testing, marking, quality requirements, terminology and other relevant parameters.
Excluded from the scope are:
safety and relief valves and other pressure relief devices which are the responsibility of ISO/TC 185
Safety devices for protection against excessive pressure;
production valves for wellhead equipment and valves for cross country pipelines for the petroleum
and natural gas industries which are the responsibility of ISO/TC 67 Materials, equipment and
offshore structures for petroleum, petrochemical and natural gas industries;
valves forming the final control element used for industrial process control systems which are the
responsibility of IEC/TC 65 Industrial-process measurement, control and automation;
valves having an envelope predominantly made of plastics which are the responsibility of
ISO/TC 138 Plastics pipes, fittings and valves for the transport of fluids;
Petroleum Exploration and Extraction Technical Standards Committee
42
valves for sanitary use;
solenoids
Total number of published ISO standards related to the TC and its SCs (number includes updates):
24
Number of published ISO standards under the direct responsibility of TC 153 (number includes updates):
11
(P) Participating countries: 19
(O) Observing countries: 25
Irelands membership status -
Standards published by ISO/TC 153
ISO 5208:2015 Industrial valves -- Pressure testing of metallic valves
ISO 5209:1977 General purpose industrial valves – Marking
ISO 5210:1991 Industrial valves -- Multi-turn valve actuator attachments
ISO 5211:2001 Industrial valves -- Part-turn actuator attachments
ISO 5752:1982 Metal valves for use in flanged pipe systems -- Face-to-face and centre-to-face dimensions
ISO 6002:1992 Bolted bonnet steel gate valves
ISO 6552:1980 Automatic steam traps -- Definition of technical terms
ISO 6552:1980/Cor 1:2009
ISO 6553:1980 Automatic steam traps – Marking
ISO 6552:1980/Cor 1:2009
ISO 6553:1980 Automatic steam traps – Marking
ISO 6554:1980 Flanged automatic steam traps -- Face-to-face dimensions
ISO 6704:1982 Automatic steam traps – Classification
ISO 6948:1981 Automatic steam traps -- Production and performance characteristic tests
ISO 7121:2006 Steel ball valves for general-purpose industrial applications
ISO 7841:1988 Automatic steam traps -- Determination of steam loss -- Test methods
ISO 7842:1988
Petroleum Exploration and Extraction Technical Standards Committee
43
Automatic steam traps -- Determination of discharge capacity -- Test methods
ISO 10434:2004 Bolted bonnet steel gate valves for the petroleum, petrochemical and allied industries
ISO 10497:2010 Testing of valves -- Fire type-testing requirements
ISO 10631:2013 Metallic butterfly valves for general purposes
ISO 12149:1999 Bolted bonnet steel globe valves for general-purpose applications
ISO 15761:2002 Steel gate, globe and check valves for sizes DN 100 and smaller, for the petroleum and natural gas industries
ISO 15848-1:2015 Industrial valves -- Measurement, test and qualification procedures for fugitive emissions -- Part 1: Classification system and qualification procedures for type testing of valves
ISO 15848-2:2015 Industrial valves -- Measurement, test and qualification procedures for fugitive emissions -- Part 2: Production acceptance test of valves
ISO 17292:2015 Metal ball valves for petroleum, petrochemical and allied industries
ISO 28921-1:2013 Industrial valves -- Isolating valves for low-temperature applications -- Part 1: Design, manufacturing and production testing
ISO 28921-2:2015 Industrial valves -- Isolating valves for low-temperature applications -- Part 2: Type testing
9.6 ISO/TC 192 - Gas turbines
Secretariat: ANSI Secretary: Mr. Robin Proctor Chairperson: Mr. Benjamin Wiant (USA) until end 2016 ISO Central Secretariat contact: M. Charles-Pierre Bazin de Caix Editorial Programme Manager(s): Ms Nicola Perou Creation date: 1988
The scope of work of ISO/TC 192 is the standardization in the field of all aspects of gas turbine design, application, installation, operation and maintenance, including simple turbine cycles, combined cycle systems, definitions, procurement, acceptance, performance, environment (on the gas turbine itself and the external environment) and methods of test.
ISO/TC 192 is responsible for preparing horizontal standards for all types of gas turbines. Work on aero gas turbine engines shall be undertaken in liaison with those technique committees having the primary responsibility.
Note: ISO/TC 20 Aircraft and space vehicles, has the primary responsibility of preparing standards relative to the specific application of gas turbines to aerospace.
Total number of published ISO standards related to the TC and its SCs (number includes updates):
17
Number of published ISO standards under the direct responsibility of TC 192 (number includes updates):
17
Petroleum Exploration and Extraction Technical Standards Committee
44
Participating countries: 15
Observing countries: 11
Irelands membership status -
Standards published by ISO/TC 192
ISO 2314:2009 Gas turbines -- Acceptance tests
ISO 3977-1:1997 Gas turbines -- Procurement -- Part 1: General introduction and definitions
ISO 3977-2:1997 Gas turbines -- Procurement -- Part 2: Standard reference conditions and ratings
ISO 3977-3:2004 Gas turbines -- Procurement -- Part 3: Design requirements
ISO 3977-4:2002 Gas turbines -- Procurement -- Part 4: Fuels and environment
ISO 3977-5:2001 Gas turbines -- Procurement -- Part 5: Applications for petroleum and natural gas industries
ISO 3977-7:2002 Gas turbines -- Procurement -- Part 7: Technical information
ISO 3977-8:2002 Gas turbines -- Procurement -- Part 8: Inspection, testing, installation and commissioning
ISO 3977-9:1999 Gas turbines -- Procurement -- Part 9: Reliability, availability, maintainability and safety
ISO 10494:1993 Gas turbines and gas turbine sets -- Measurement of emitted airborne noise -- Engineering/survey method
ISO 11042-1:1996 Gas turbines -- Exhaust gas emission -- Part 1: Measurement and evaluation
ISO 11042-2:1996 Gas turbines -- Exhaust gas emission -- Part 2: Automated emission monitoring
ISO 11086:1996 Gas turbines – Vocabulary
ISO 19372:2015 Microturbines applications – Safety
ISO 19860:2005 Gas turbines -- Data acquisition and trend monitoring system requirements for gas turbine installations
ISO 21789:2009 Gas turbine applications -- Safety
ISO 26382:2010 Cogeneration systems -- Technical declarations for planning, evaluation and procurement
Petroleum Exploration and Extraction Technical Standards Committee
45
9.7 CEN/TC 12
Title: Materials, equipment and offshore structures for petroleum, petrochemical and natural gas industries
Status: Active Secretariat: NEN (Dutch National Standards Body) Secretary: Mr. J. Darkhorst([email protected])) Chairperson: CCMC PM: Mrs J. Frankowska
There are no Working Groups in this Technical Committee.
This Technical Committee mirrors the work of ISO/TC 67 at a European level and adopts, where appropriate, ISO Standards as European Standards.
Where modifications have been made to ISO Standards they have been published by the Technical Committee as separate European Standards.
All Standards published by this CEN Technical Committee are adopted as Irish Standards.
Standards published by CEN/TC 12
CEN ISO/TR 10400:2011 Petroleum and natural gas industries - Equations and calculations for the properties of casing, tubing, drill pipe and line pipe used as casing or tubing (ISO/TR 10400:2007)
CEN ISO/TR 13624-2:2013 Petroleum and natural gas industries - Drilling and production equipment - Part 2: Deepwater drilling riser methodologies, operations, and integrity technical report (ISO/TR 13624-2:2009)
CEN ISO/TR 13881:2011 Petroleum and natural gas industries - Classification and conformity assessment of products, processes and services (ISO/TR 13881:2000)
CEN ISO/TR 19905-2:2013 Petroleum and natural gas industries - Site-specific assessment of mobile offshore units - Part 2: Jack-ups commentary and detailed sample calculation (ISO/TR 19905-2:2012)
CEN ISO/TS 12747:2013 Petroleum and natural gas industries - Pipeline transportation systems - Recommended practice for pipeline life extension (ISO/TS 12747:2011)
CEN ISO/TS 17969:2015 Petroleum, petrochemical and natural gas industries - Guidelines on competency for personnel (ISO/TS 17969:2015)
CEN ISO/TS 27469:2011 Petroleum, petrochemical and natural gas industries - Method of test for fire dampers (ISO/TS 27469:2010)
CEN ISO/TS 29001:2011 Petroleum, petrochemical and natural gas industries - Sector-specific quality management systems - Requirements for product and service supply organizations (ISO/TS 29001:2010)
CEN/TR 14549:2004 Guide to the use of ISO 15649 and ANSI/ASME B31.3 for piping in Europe in compliance with the Pressure Equipment Directive
EN 13942:2009 Petroleum and natural gas industries - Pipeline transportation systems - Pipeline valves (ISO 14313:2007 modified)
EN 13942:2009/AC:2009
Petroleum Exploration and Extraction Technical Standards Committee
46
EN 14161:2011+A1:2015 Petroleum and natural gas industries - Pipeline transportation systems (ISO 13623:2009 modified)
EN 14163:2001 Petroleum and natural gas industries - Pipeline transportation systems - Welding of pipelines (ISO 13847:2000 modified)
EN 14163:2001/AC:2006
EN 14870-1:2011 Petroleum and natural gas industries - Induction bends, fittings and flanges for pipeline transportation systems - Part 1: Induction bends (ISO 15590-1:2009 modified)
EN 14870-2:2004 Petroleum and natural gas industries - Induction bends, fittings and flanges for pipeline transportation systems - Part 2: Fittings (ISO 15590-2:2003 modified)
EN 14870-3:2006 Petroleum and natural gas industries - Induction bends, fittings and flanges for pipeline transportation systems - Part 3: Flanges (ISO 15590-3:2004, modified)
EN ISO 10405:2006 Petroleum and natural gas industries - Care and use of casing and tubing (ISO 10405:2006)
EN ISO 10407-2:2008 Petroleum and natural gas industries - Rotary drilling equipment - Part 2: Inspection and classification of used drill stem elements (ISO 10407-2:2008)
EN ISO 10407-2:2008/AC:2009
EN ISO 10414-1:2008 Petroleum and natural gas industries - Field testing of drilling fluids - Part 1: Water-based fluids (ISO 10414-1:2008)
EN ISO 10414-2:2011 Petroleum and natural gas industries - Field testing of drilling fluids - Part 2: Oil-based fluids (ISO 10414-2:2011)
EN ISO 10416:2009 Petroleum and natural gas industries - Drilling fluids - Laboratory testing (ISO 10416:2008)
EN ISO 10417:2004 Petroleum and natural gas industries - Subsurface safety valve systems - Design, installation, operation and redress (ISO 10417:2004)
EN ISO 10418:2003 Petroleum and natural gas industries - Offshore production installations - Basic surface process safety systems (ISO 10418:2003)
EN ISO 10418:2003/AC:2009
EN ISO 10423:2009 Petroleum and natural gas industries - Drilling and production equipment - Wellhead and christmas tree equipment (ISO 10423:2009)
EN ISO 10424-1:2004 Petroleum and natural gas industries - Rotary drilling equipment - Part 1: Rotary drill stem elements (ISO 10424-1:2004)
EN ISO 10424-2:2007 Petroleum and natural gas industries - Rotary drilling equipment - Part 2: Threading and gauging of rotary shouldered thread connections (ISO 10424-2:2007)
EN ISO 10426-1:2009 Petroleum and natural gas industries - Cements and materials for well cementing - Part 1: Specification (ISO 10426-1:2009)
EN ISO 10426-1:2009/AC:2010
EN ISO 10426-2:2003+A1:2005 Petroleum and natural gas industries - Cements and materials for well cementing - Part 2: Testing of well
Petroleum Exploration and Extraction Technical Standards Committee
47
cements - Amendment 1: Water-wetting capability testing (ISO 10426-2:2003+A1:2005)
EN ISO 10426-2:2003/AC:2007
EN ISO 10426-3:2004 Petroleum and natural gas industries - Cements and materials for well cementing - Part 3: Testing of deepwater well cement formulations (ISO 10426-3:2003)
EN ISO 10426-4:2004 Petroleum and natural gas industries - Cements and materials for well cementing - Part 4: Preparation and testing of foamed cement slurries at atmospheric pressure (ISO 10426-4:2004)
EN ISO 10426-5:2005 Petroleum and natural gas industries - Cements and materials for well cementing - Part 5: Determination of shrinkage and expansion of well cement formulations at atmospheric pressure (ISO 10426-5:2004)
EN ISO 10426-6:2008 Petroleum and natural gas industries - Cements and materials for well cementing - Part 6: Methods for determining the static gel strength of cement formulations (ISO 10426-6:2008)
EN ISO 10427-1:2001 Petroleum and natural gas industries - Casing centralizers - Part 1: Bow-spring casing centralizers (ISO 10427-1:2001)
EN ISO 10427-2:2004 Petroleum and natural gas industries - Equipment for well cementing - Part 2: Centralizer placement and stop-collar testing (ISO 10427-2:2004)
EN ISO 10427-3:2004 Petroleum and natural gas industries - Equipment for well cementing - Part 3: Performance testing of cementing float equipment (ISO 10427-3:2003)
EN ISO 10432:2004 Petroleum and natural gas industries - Downhole equipment - Subsurface safety valve equipment (ISO 10432:2004)
EN ISO 10437:2003 Petroleum, petrochemical and natural gas industries - Steam turbines - Special-purpose applications (ISO 10437:2003)
EN ISO 10438-1:2007 Petroleum, petrochemical and natural gas industries - Lubrication, shaft-sealing and control-oil systems and auxiliaries - Part 1: General requirements (ISO 10438-1:2007)
EN ISO 10438-2:2007 Petroleum, petrochemical and natural gas industries - Lubrication, shaft-sealing and control-oil systems and auxiliaries - Part 2: Special-purpose oil systems (ISO 10438-2:2007)
EN ISO 10438-3:2007 Petroleum, petrochemical and natural gas industries - Lubrication, shaft-sealing and control-oil systems and auxiliaries - Part 3: General-purpose oil systems (ISO 10438-3:2007)
EN ISO 10438-4:2007 Petroleum, petrochemical and natural gas industries - Lubrication, shaft-sealing and control-oil systems and auxiliaries - Part 4: Self-acting gas seal support systems (ISO 10438-4:2007)
EN ISO 10439-1:2015 Petroleum, petrochemical and natural gas industries - Axial and centrifugal compressors and expander-compressors - Part 1: General requirements (ISO 10439-1:2015)
EN ISO 10439-2:2015 Petroleum, petrochemical and natural gas industries - Axial and centrifugal compressors and expander-compressors - Part 2: Non-integrally geared centrifugal and axial compressors (ISO 10439-2:2015)
EN ISO 10439-3:2015 Petroleum, petrochemical and natural gas industries - Axial and centrifugal compressors and expander-compressors - Part 3: Integrally geared centrifugal compressors (ISO 10439-3:2015)
EN ISO 10439-4:2015 Petroleum, petrochemical and natural gas industries - Axial and centrifugal compressors and expander-
Petroleum Exploration and Extraction Technical Standards Committee
48
compressors - Part 4: Expander-compressors(ISO 10439-4:2015)
EN ISO 10440-1:2007 Petroleum, petrochemical and natural gas industries - Rotary-type positive-displacement compressors - Part 1: Process compressors (ISO 10440-1:2007)
EN ISO 10440-2:2001 Petroleum and natural gas industries - Rotary-type positive-displacement compressors - Part 2: Packaged air compressors (oil-free) (ISO 10440-2:2001)
EN ISO 10441:2007 Petroleum, petrochemical and natural gas industries - Flexible couplings for mechanical power transmission - Special-purpose applications (ISO 10441:2007)
EN ISO 10442:2002 Petroleum, chemical and gas service industries - Packaged, integrally geared centrifugal air compressors (ISO 10442:2002)
EN ISO 11960:2014 Petroleum and natural gas industries - Steel pipes for use as casing or tubing for wells (ISO 11960:2014)
EN ISO 11961:2008 Petroleum and natural gas industries - Steel drill pipe (ISO 11961:2008)
EN ISO 11961:2008/AC:2009
EN ISO 12211:2012 Petroleum, petrochemical and natural gas industries - Spiral plate heat exchangers (ISO 12211:2012)
EN ISO 12212:2012 Petroleum, petrochemical and natural gas industries - Hairpin-type heat exchangers (ISO 12212:2012)
EN ISO 12736:2014 Petroleum and natural gas industries - Wet thermal insulation coatings for pipelines, flow lines, equipment and subsea structures (ISO 12736:2014)
EN ISO 13085:2014 Petroleum and natural gas industries - Aluminium alloy pipe for use as tubing for wells (ISO 13085:2014)
EN ISO 13354:2014 Petroleum and natural gas industries - Drilling and production equipment - Shallow gas diverter equipment (ISO 13354:2014)
EN ISO 13500:2008+A1:2010 Petroleum and natural gas industries - Drilling fluid materials - Specifications and tests - Amendment 1: Barite 4,1 (ISO 13500:2008+AMD 1:2010)
EN ISO 13501:2011 Petroleum and natural gas industries - Drilling fluids - Processing equipment evaluation (ISO 13501:2011)
EN ISO 13503-1:2011 Petroleum and natural gas industries - Completion fluids and materials - Part 1: Measurement of viscous properties of completion fluids (ISO 13503-1:2011)
EN ISO 13503-2:2006+A1:2009 Petroleum and natural gas industries - Completion fluids and materials - Part 2: Measurement of properties of proppants used in hydraulic fracturing and gravel-packing operations - Amendment 1: Addition of Annex B: Proppand specification (ISO 13503-2:2006+Amd 1:2009)
EN ISO 13503-3:2005 Petroleum and natural gas industries - Completion fluids and materials - Part 3: Testing of heavy brines (ISO 13503-3:2005)
EN ISO 13503-3:2005/AC:2007
EN ISO 13503-4:2006 Petroleum and natural gas industries - Completion fluids and materials - Part 4: Procedure for measuring stimulation and gravel-pack fluid leakoff under static conditions (ISO 13503-4:2006)
EN ISO 13503-5:2006 Petroleum and natural gas industries - Completion fluids and materials - Part 5: Procedures for measuring the
Petroleum Exploration and Extraction Technical Standards Committee
49
long-term conductivity of proppants (ISO 13503-5:2006)
EN ISO 13503-6:2014 Petroleum and natural gas industries - Completion fluides and materials - Part 6: Procedure for measuring leakoff of completion fluids under dynamic conditions (ISO 13503-6:2014)
EN ISO 13533:2001 Petroleum and natural gas industries - Drilling and production equipment - Drill-through equipment (ISO 13533:2001)
EN ISO 13533:2001/AC:2006
EN ISO 13534:2000 Petroleum and natural gas industries - Drilling and production equipment - Inspection, maintenance, repair and remanufacture of hoisting equipment (ISO 13534:2000)
EN ISO 13535:2000 Petroleum and natural gas industries - Drilling and production equipment - Hoisting equipment (ISO 13535:2000)
EN ISO 13624-1:2009 Petroleum and natural gas industries - Drilling and production equipment - Part 1: Design and operation of marine drilling riser equipment (ISO 13624-1:2009)
EN ISO 13625:2002 Petroleum and natural gas industries - Drilling and production equipment - Marine drilling riser couplings (ISO 13625:2002)
EN ISO 13626:2004 Petroleum and natural gas industries - Drilling and production equipment - Drilling and well-servicing structures (ISO 13626:2003)
EN ISO 13628-1:2005+A1:2010 Petroleum and natural gas industries - Design and operation of subsea production systems - Part 1: General requirements and recommendations - Amendment 1: Revised Clause 6 (ISO 13628-1:2005+Amd 1:2010)
EN ISO 13628-10:2006 Petroleum and natural gas industries - Design and operation of subsea production systems - Part 10: Specification for bonded flexible pipe (ISO 13628-10:2006)
EN ISO 13628-11:2008 Petroleum and natural gas industries - Design and operation of subsea production systems - Part 11: Flexible pipe systems for subsea and marine applications (ISO 13628-11:2007)
EN ISO 13628-11:2008/AC:2009
EN ISO 13628-15:2011 Petroleum and natural gas industries - Design and operation of subsea production systems - Part 15: Subsea structures and manifolds (ISO 13628-15:2011)
EN ISO 13628-2:2006 Petroleum and natural gas industries - Design and operation of subsea production systems - Part 2: Unbonded flexible pipe systems for subsea and marine applications (ISO 13628-2:2006)
EN ISO 13628-2:2006/AC:2009
EN ISO 13628-3:2000 Petroleum and natural gas industries - Design and operation of subsea production systems - Part 3: Through flowline (TFL) systems (ISO 13628-3:2000)
EN ISO 13628-4:2010 Petroleum and natural gas industries - Design and operation of subsea production systems - Part 4: Subsea wellhead and tree equipment (ISO 13628-4:2010)
EN ISO 13628-4:2010/AC:2011
EN ISO 13628-5:2009 Petroleum and natural gas industries - Design and operation of subsea production systems - Part 5: Subsea umbilicals (ISO 13628-5:2009)
Petroleum Exploration and Extraction Technical Standards Committee
50
EN ISO 13628-6:2006 Petroleum and natural gas industries - Design and operation of subsea production systems - Part 6: Subsea production control systems (ISO 13628-6:2006)
EN ISO 13628-7:2006 Petroleum and natural gas industries - Design and operation of subsea production systems - Part 7: Completion/workover riser systems (ISO 13628-7:2005)
EN ISO 13628-8:2006 Petroleum and natural gas industries - Design and operation of subsea production systems - Part 8: Remotely Operated Vehicle (ROV) interfaces on subsea production systems (ISO 13628-8:2002)
EN ISO 13628-9:2006 Petroleum and natural gas industries - Design and operation of subsea production systems - Part 9: Remotely Operated Tool (ROT) intervention systems (ISO 13628-9:2000)
EN ISO 13631:2002 Petroleum and natural gas industries - Packaged reciprocating gas compressors (ISO 13631:2002)
EN ISO 13678:2012 Petroleum and natural gas industries - Evaluation and testing of thread compounds for use with casing, tubing, line pipe and drill stem elements (ISO 13678:2010)
EN ISO 13679:2006 Petroleum and natural gas industries - Procedures for testing casing and tubing connections (ISO 13679:2002)
EN ISO 13680:2010 Petroleum and natural gas industries - Corrosion-resistant alloy seamless tubes for use as casing, tubing and coupling stock - Technical delivery conditions (ISO 13680:2010)
EN ISO 13691:2002 Petroleum and natural gas industries - High-speed special-purpose gear units (ISO 13691:2001)
EN ISO 13702:2015 Petroleum and natural gas industries - Control and mitigation of fires and explosions on offshore production installations - Requirements and guidelines (ISO 13702:2015)
EN ISO 13703:2000 Petroleum and natural gas industries - Design and installation of piping systems on offshore production platforms (ISO 13703:2000)
EN ISO 13703:2000/AC:2007
EN ISO 13704:2007 Petroleum, petrochemical and natural gas industries - Calculation of heater-tube thickness in petroleum refineries (ISO 13704:2007)
EN ISO 13704:2007/AC:2009
EN ISO 13705:2012 Petroleum, petrochemical and natural gas industries - Fired heaters for general refinery service (ISO 13705:2012)
EN ISO 13706:2011 Petroleum, petrochemical and natural gas industries - Air-cooled heat exchangers (ISO 13706:2011)
EN ISO 13709:2009 Centrifugal pumps for petroleum, petrochemical and natural gas industries (ISO 13709:2009)
EN ISO 13710:2004 Petroleum, petrochemical and natural gas industries - Reciprocating positive displacement pumps (ISO 13710:2004)
EN ISO 14224:2006 Petroleum, petrochemical and natural gas industries - Collection and exchange of reliability and maintenance data for equipment (ISO 14224:2006)
EN ISO 14310:2008 Petroleum and natural gas industries - Downhole equipment - Packers and bridge plugs (ISO 14310:2008)
Petroleum Exploration and Extraction Technical Standards Committee
51
EN ISO 14691:2008 Petroleum, petrochemical and natural gas industries - Flexible couplings for mechanical power transmission - General-purpose applications (ISO 14691:2008)
EN ISO 14692-1:2002 Petroleum and natural gas industries - Glass-reinforced plastics (GRP) piping - Part 1: Vocabulary, symbols, applications and materials (ISO 14692-1:2002)
EN ISO 14692-2:2002 Petroleum and natural gas industries - Glass-reinforced plastics (GRP) piping - Part 2: Qualification and manufacture (ISO 14692-2:2002)
EN ISO 14692-2:2002/AC:2006
EN ISO 14692-3:2002 Petroleum and natural gas industries - Glass-reinforced plastics (GRP) piping - Part 3: System design (ISO 14692-3:2002)
EN ISO 14692-3:2002/AC:2006
EN ISO 14692-4:2002 Petroleum and natural gas industries - Glass-reinforced plastics (GRP) piping - Part 4: Fabrication, installation and operation (ISO 14692-4:2002)
EN ISO 14692-4:2002/AC:2007
EN ISO 14693:2003 Petroleum and natural gas industries - Drilling and well-servicing equipment (ISO 14693:2003)
EN ISO 14723:2009 Petroleum and natural gas industries - Pipeline transportation systems - Subsea pipeline valves (ISO 14723:2009)
EN ISO 14998:2013 Petroleum and natural gas industries - Downhole equipment - Completion accessories (ISO 14998:2013)
EN ISO 15136-1:2009 Petroleum and natural gas industries - Progressing cavity pump systems for artificial lift - Part 1: Pumps (ISO 15136-1:2009)
EN ISO 15136-2:2006 Petroleum and natural gas industries - Progressing cavity pump systems for artificial lift - Part 2: Surface-drive systems (ISO 15136-2:2006)
EN ISO 15138:2007 Petroleum and natural gas industries - Offshore production installations - Heating, ventilation and air-conditioning (ISO 15138:2007)
EN ISO 15156-1:2015 Petroleum and natural gas industries - Materials for use in H2S-containing environments in oil and gas production - Part 1: General principles for selection of cracking-resistant materials (ISO 15156-1:2015)
EN ISO 15156-2:2015 Petroleum and natural gas industries - Materials for use in H2S-containing environments in oil and gas production - Part 2: Cracking-resistant carbon and low alloy steels, and the use of cast irons (ISO 15156-2:2015)
EN ISO 15156-3:2015 Petroleum and natural gas industries - Materials for use in H2S-containing environments in oil and gas production - Part 3: Cracking-resistant CRAs (corrosion-resistant alloys) and other alloys (ISO 15156-3:2015)
EN ISO 15463:2003 Petroleum and natural gas industries - Field inspection of new casing, tubing and plain-end drill pipe (ISO 15463:2003)
EN ISO 15463:2003/AC:2009
EN ISO 15544:2010 Petroleum and natural gas industries - Offshore production installations - Requirements and guidelines for emergency response (ISO 15544:2000, including Amd 1:2009)
Petroleum Exploration and Extraction Technical Standards Committee
52
EN ISO 15546:2011 Petroleum and natural gas industries - Aluminium alloy drill pipe (ISO 15546:2011)
EN ISO 15547-1:2005 Petroleum, petrochemical and natural gas industries - Plate-type heat exchangers - Part 1: Plate-and-frame heat exchangers (ISO 15547-1:2005)
EN ISO 15547-2:2005 Petroleum, petrochemical and natural gas industries - Plate-type heat exchangers - Part 2: Brazed aluminium plate-fin heat exchangers (ISO 15547-2:2005)
EN ISO 15551-1:2015 Petroleum and natural gas industries - Drilling and production equipment - Part 1: Electric submersible pump systems for artificial lift (ISO 15551-1:2015)
EN ISO 15663-1:2006 Petroleum and natural gas industries - Life cycle costing - Part 1: Methodology (ISO 15663-1:2000)
EN ISO 15761:2002 Steel gate, globe and check valves for sizes DN 100 and smaller, for the petroleum and natural gas industries (ISO 15761:2002)
EN ISO 16070:2005 Petroleum and natural gas industries - Downhole equipment - Lock mandrels and landing nipples (ISO 16070:2005)
EN ISO 16708:2006 Petroleum and natural gas industries - Pipeline transportation systems - Reliability-based limit state methods (ISO 16708:2006)
EN ISO 16812:2007 Petroleum, petrochemical and natural gas industries - Shell-and-tube heat exchangers (ISO 16812:2007)
EN ISO 16961:2015 Petroleum, petrochemical and natural gas industries - Internal coating and lining of steel storage tanks (ISO 16961:2015)
EN ISO 17078-1:2004+A1:2010 Petroleum and natural gas industries - Drilling and production equipment - Part 1: Side-pocket mandrels - Amendment 1 (ISO 17078-1:2004+Amd 1:2010)
EN ISO 17078-2:2007 Petroleum and natural gas industries - Drilling and production equipment - Part 2: Flow-control devices for side-pocket mandrels (ISO 17078-2:2007)
EN ISO 17078-2:2007/AC:2009
EN ISO 17078-3:2009 Petroleum and natural gas industries - Drilling and production equipment - Part 3: Running tools, pulling tools and kick-over tools and latches for side-pocket mandrels (ISO 17078-3:2009)
EN ISO 17078-4:2010 Petroleum and natural gas industries - Drilling and production equipment - Part 4: Practices for side-pocket mandrels and related equipment (ISO 17078-4:2010)
EN ISO 17776:2002 Petroleum and natural gas industries - Offshore production installations - Guidelines on tools and techniques for hazard identification and risk assessment (ISO 17776:2000)
EN ISO 17824:2014 Petroleum and natural gas industries - Downhole equipment - Sand screens (ISO 17824:2009)
EN ISO 17945:2015 Petroleum, petrochemical and natural gas industries - Metallic materials resistant to sulfide stress cracking in corrosive petroleum refining environments (ISO 17945:2015)
EN ISO 19900:2013 Petroleum and natural gas industries - General requirements for offshore structures (ISO 19900:2013)
EN ISO 19901-1:2015 Petroleum and natural gas industries - Specific requirements for offshore structures - Part 1: Metocean design
Petroleum Exploration and Extraction Technical Standards Committee
53
and operating considerations (ISO 19901-1:2015)
EN ISO 19901-2:2004 Petroleum and natural gas industries - Specific requirements for offshore structures - Part 2: Seismic design procedures and criteria (ISO 19901-2:2004)
EN ISO 19901-3:2014 Petroleum and natural gas industries - Specific requirements for offshore structures - Part 3: Topsides structure (ISO 19901-3:2014)
EN ISO 19901-4:2003 Petroleum and natural gas industries - Specific requirements for offshore structures - Part 4: Geotechnical and foundation design considerations (ISO 19901-4:2003)
EN ISO 19901-5:2003 Petroleum and natural gas industries - Specific requirements for offshore structures - Part 5: Weight control during engineering and construction (ISO 19901-5:2003)
EN ISO 19901-6:2009 Petroleum and natural gas industries - Specific requirements for offshore structures - Part 6: Marine operations (ISO 19901-6:2009)
EN ISO 19901-6:2009/AC:2011
EN ISO 19901-7:2013 Petroleum and natural gas industries - Specific requirements for offshore structures - Part 7: Stationkeeping systems for floating offshore structures and mobile offshore units (ISO 19901-7:2013)
EN ISO 19901-8:2015 Petroleum and natural gas industries - Specific requirements for offshore structures - Part 8: Marine soil investigations (ISO 19901-8:2014)
EN ISO 19902:2007+A1:2013 Petroleum and natural gas industries - Fixed steel offshore structures (ISO 19902:2007+Amd 1:2013)
EN ISO 19903:2006 Petroleum and natural gas industries - Fixed concrete offshore structures (ISO 19903:2006)
EN ISO 19904-1:2006 Petroleum and natural gas industries - Floating offshore structures - Part 1: Monohulls, semi-submersibles and spars (ISO 19904-1:2006)
EN ISO 19905-1:2012 Petroleum and natural gas industries - Site-specific assessment of mobile offshore units - Part 1: Jack-ups (ISO 19905-1:2012)
EN ISO 19906:2010 Petroleum and natural gas industries - Arctic offshore structures (ISO 19906:2010)
EN ISO 20312:2011 Petroleum and natural gas industries - Design and operating limits of drill strings with aluminium alloy components (ISO 20312:2011)
EN ISO 20815:2010 Petroleum, petrochemical and natural gas industries - Production assurance and reliability management (ISO 20815:2008, Corrected version 2009-06-15)
EN ISO 21049:2004 Pumps - Shaft sealing systems for centrifugal and rotary pumps (ISO 21049:2004)
EN ISO 21329:2004 Petroleum and natural gas industries - Pipeline transportation systems - Test procedures for mechanical connectors (ISO 21329:2004)
EN ISO 21457:2010 Petroleum, petrochemical and natural gas industries - Materials selection and corrosion control for oil and gas production systems (ISO 21457:2010)
EN ISO 23251:2007+A1:2008 Petroleum, petrochemical and natural gas industries - Pressure-relieving and depressuring systems -
Petroleum Exploration and Extraction Technical Standards Committee
54
Amendment 1 (ISO 23251:2007+Amd 1:2008)
EN ISO 23251:2007/AC:2008
EN ISO 23936-1:2009 Petroleum, petrochemical and natural gas industries - Non-metallic materials in contact with media related to oil and gas production - Part 1: Thermoplastics (ISO 23936-1:2009)
EN ISO 23936-2:2011 Petroleum, petrochemical and natural gas industries - Non-metallic materials in contact with media related to oil and gas production - Part 2: Elastomers (ISO 23936-2:2011)
EN ISO 24817:2015 Petroleum, petrochemical and natural gas industries - Composite repairs for pipework - Qualification and design, installation, testing and inspection (ISO 24817:2015)
EN ISO 25457:2008 Petroleum, petrochemical and natural gas industries - Flare details for general refinery and petrochemical service (ISO 25457:2008)
EN ISO 27509:2012 Petroleum and natural gas industries - Compact flanged connections with IX seal ring (ISO 27509:2012)
EN ISO 27509:2012/AC:2013
EN ISO 27627:2014 Petroleum and natural gas industries - Aluminium alloy drill pipe thread connection gauging (ISO 27627:2014)
EN ISO 28300:2008 Petroleum, petrochemical and natural gas industries - Venting of atmospheric and low-pressure storage tanks (ISO 28300:2008)
EN ISO 28300:2008/AC:2009
EN ISO 28781:2010 Petroleum and natural gas industries - Drilling and production equipment - Subsurface barrier valves and related equipment (ISO 28781:2010)
EN ISO 3977-5:2003 Gas turbines - Procurement - Part 5: Applications for petroleum and natural gas industries (ISO 3977-5:2001)
EN ISO 3977-5:2003/AC:2007
Petroleum Exploration and Extraction Technical Standards Committee
55
9.8 CEN/TC 69
Title: Industrial valves
Status: Active Secretariat: AFNOR (French National Standards Body) Secretary: Ms H. Cros mailto... ( [email protected] ) Chairperson: Mr P. Vinzio (FR) CCMC PM: Mr T. Legrand mailto... ( [email protected] )
There are 18 Working Groups in this Technical Committee of which 6 are active.
This Technical Committee mirrors the relevant work of ISO/TC 138, ISO/TC 153 and ISO/TC 185 at a European level and adopts, where appropriate, ISO Standards as European Standards.
The scope of work covered by the Technical Committee includes the standardization of valves for all industrial applications and for all types of fluids, including steam traps; valve actuator interface; safety devices against excessive pressure (safety valves and bursting disks); control valves (excluding the actuator element and their interface); but excluding sanitary valves as defined by CEN/TC 164/WG 8.
Where modifications have been made to ISO Standards they have been published by the Technical Committee as separate European Standards.
All Standards published by this CEN Technical Committee are adopted as Irish Standards.
Standards published by CEN/TC 69
EN 1171:2015 Industrial valves - Cast iron gate valves
EN 12266-1:2012 Industrial valves - Testing of metallic valves - Part 1: Pressure tests, test procedures and acceptance criteria - Mandatory requirements
EN 12266-2:2012 Industrial valves - Testing of metallic valves - Part 2: Tests, test procedures and acceptance criteria - Supplementary requirements
EN 12288:2010 Industrial valves - Copper alloy gate valves
EN 12334:2001 Industrial valves - Cast iron check valves
EN 12351:2010 Industrial valves - Protective caps for valves with flanged connections
EN 12516-1:2014 Industrial valves - Shell design strength - Part 1: Tabulation method for steel valve shells
EN 12516-2:2014 Industrial valves - Shell design strength - Part 2: Calculation method for steel valve shells
EN 12516-3:2002 Valves - Shell design strength - Part 3: Experimental method
EN 12516-4:2014 Industrial valves - Shell design strength - Part 4: Calculation method for valve shells manufactured in metallic materials other than steel
Petroleum Exploration and Extraction Technical Standards Committee
56
EN 12567:2000 Industrial valves - Isolating valves for LNG - Specification for suitability and appropriate verification tests
EN 12569:1999 Industrial valves - Valves for chemical and petrochemical process industry - Requirements and tests
EN 12570:2000 Industrial valves - Method for sizing the operating element
EN 12627:1999 Industrial valves - Butt welding ends for steel valves
EN 1267:2012 Industrial valves - Test of flow resistance using water as test fluid
EN 12760:1999 Valves - Socket welding ends for steel valves
EN 12982:2009 Industrial valves - End-to-end and centre-to-end dimensions for butt welding end valves
EN 13397:2001 Industrial valves - Diaphragm valves made of metallic materials
EN 1349:2009 Industrial process control valves
EN 13547:2013 Industrial valves - Copper alloy ball valves
EN 13709:2010 Industrial valves - Steel globe and globe stop and check valves
EN 13774:2013 Valves for gas distribution systems with maximum operating pressure less than or equal to 16 bar - Performance requirements
EN 13789:2010 Industrial valves - Cast iron globe valves
EN 14141:2013 Valves for natural gas transportation in pipelines - Performance requirements and tests
EN 14341:2006 Industrial valves - Steel check valves
EN 1503-4:2002 Valves - Materials for bodies, bonnets and covers - Part 4: Copper alloys specified in European Standards
EN 15081:2007 Industrial valves - Mounting kits for part-turn valve actuator attachment
EN 15714-1:2009 Industrial valves - Actuators - Part 1: Terminology and definitions
EN 15714-2:2009 Industrial valves - Actuators - Part 2: Electric actuators for industrial valves - Basic requirements
EN 15714-3:2009 Industrial valves - Actuators - Part 3: Pneumatic part-turn actuators for industrial valves - Basic requirements
EN 15714-4:2009 Industrial valves - Actuators - Part 4: Hydraulic part-turn actuators for industrial valves - Basic requirements
EN 16722:2015 Industrial valves - End-to-end and centre-to-end dimensions for valves with threaded ends
EN 19:2002 Industrial valves - Marking of metallic valves
EN 1983:2013
Petroleum Exploration and Extraction Technical Standards Committee
57
Industrial valves - Steel ball valves
EN 1984:2010 Industrial valves - Steel gate valves
EN 26553:1991 Automatic steam traps - Marking (ISO 6553:1980)
EN 26554:1991 Flanged automatic steam traps - Face-to-face dimensions (ISO 6554:1980)
EN 26704:1991 Automatic steam traps - Classification (ISO 6704:1982)
EN 26948:1991 Automatic steam traps - Production and performance characteristic tests (ISO 6948:1981)
EN 27841:1991 Automatic steam traps - Determination of steam loss - Test methods (ISO 7841:1988)
EN 27842:1991 Automatic steam traps - Determination of discharge capacity - Test methods (ISO 7842:1988)
EN 28233:1990 Thermoplastics valves - Torque - Test method (ISO 8233:1988)
EN 28659:1990 Thermoplastics valves - Fatigue strength - Test method (ISO 8659:1989)
EN 558:2008+A1:2011 Industrial valves - Face-to-face and centre-to-face dimensions of metal valves for use in flanged pipe systems - PN and Class designated valves
EN 593:2009+A1:2011 Industrial valves - Metallic butterfly valves
EN 736-1:1995 Valves - Terminology - Part 1: Definition of types of valves
EN 736-2:1997 Valves - Terminology - Part 2: Definition of components of valves
EN 736-3:2008 Valves - Terminology - Part 3: Definition of terms
EN ISO 10434:2004 Bolted bonnet steel gate valves for the petroleum, petrochemical and allied industries (ISO 10434:2004)
EN ISO 10497:2010 Testing of valves - Fire type-testing requirements (ISO 10497:2010)
EN ISO 15848-1:2015 Industrial valves - Measurement, test and qualification procedures for fugitive emissions - Part 1: Classification system and qualification procedures for type testing of valves (ISO 15848-1:2015)
EN ISO 15848-2:2015 Industrial valves - Measurement, test and qualification procedures for fugitive emissions - Part 2: Production acceptance test of valves (ISO 15848-2:2015)
EN ISO 17292:2015 Metal ball valves for petroleum, petrochemical and allied industries (ISO 17292:2015)
EN ISO 4126-1:2013 Safety devices for protection against excessive pressure - Part 1: Safety valves (ISO 4126-1:2013)
EN ISO 4126-2:2003 Safety devices for protection against excessive pressure - Part 2: Bursting disc safety devices (ISO 4126-2:2003)
Petroleum Exploration and Extraction Technical Standards Committee
58
EN ISO 4126-3:2006 Safety devices for protection against excessive pressure - Part 3: Safety valves and bursting disc safety devices in combination (ISO 4126-3:2006)
EN ISO 4126-4:2013 Safety devices for protection against excessive pressure - Part 4: Pilot-operated safety valves (ISO 4126-4:2013)
EN ISO 4126-5:2013 Safety devices for protection against excessive pressure - Part 5: Controlled safety pressure relief systems (CSPRS) (ISO 4126-5:2013)
EN ISO 4126-6:2014 Safety devices for protection against excessive pressure - Part 6: Application, selection and installation of bursting disc safety devices (ISO 4126-6:2014)
EN ISO 4126-7:2013 Safety devices for protection against excessive pressure - Part 7: Common data (ISO 4126-7:2013)
EN ISO 5210:1996 Industrial valves - Multi-turn valve actuator attachments (ISO 5210:1991)
EN ISO 5211:2001 Industrial valves - Part-turn actuator attachments (ISO 5211:2001)
Standards
Where do I get standards?All standards can be purchased in either hard or electronic form, visit www.standards.ie
A preview, scope and table of contents is available online, free-of charge, for many standards from NSAI. NSAI publish all EN and many ISO and IEC standards as equivalent Irish Standards.
Your Standards, Your SayTake an active role in how Standards can meet business needs.
NSAI has improved the opportunities for all interested parties to engage in the national standardization process. Your Standards, Your Say is where new and changing standards can be viewed and commented on, free of charge.
Visit NSAI Your Standards, Your Say at www.nsainep.ie
NSAI is the National Standards Body in Ireland.
Contact us
NSAI, 1 Swift Square, Northwood,
Santry, Dublin 9, Ireland. D09 A0E9
T +353 1 807 3800
W www.nsai.ie
Follow us
Twitter @NSAI_Standards
Youtube www.youtube.com/user/NSAImedia
LinkedIn www.linkedin.com/company/national-standards-authority-of-ireland