Performance Evaluation of Zero-Biased VCSEL for High Speed Data Transmission
1
S. Silva a , L. Pessoa a,b , J. Oliveira a,b , D. Coelho a,b , J. C. S. Castro a,b , H. M. Salgado a,b a INESC Porto, Rua Dr. Roberto Frias, 378, 4200 - 465 Porto, Portugal b Faculty of Engennering, Porto University, Rua Dr. Roberto Frias, S/N, 4200 - 465 Porto, Portugal E-mail: [email protected] ABSTRACT: In an optical transceiver, the power consumption related to the operation of the laser device takes a significant parcel of the total consumed power. Thus, in optical networks where a large number of transceiver devices are interconnected, e.g. large distributed sensor networks, it is of extremely importance to reduce this power consumption. In this work an analysis and simulation results are presented regarding the operation of a bias- free vertical-cavity surface-emitting laser (VCSEL) device, which is based on a previously developed model. The impact on bit-error rate (BER) of the increased turn-on jitter due to the bit-pattern and spontaneous emission is considered. A method for mitigating the eye-diagram distortion penalty based on the received signal equalization is also illustrated. Performance Evaluation of Zero- Biased VCSEL for High Speed Data Transmission Acknowledgments: This work was supported in part by EC Framework 7 (FP7) project DAPHNE (www.fp7daphne.eu) – Developing aircraft photonic networks (grant ACP8-GA-2009-233709). We acknowledge funding from FCT and program POCTI/FEDER under the National Plan for Scientific Hardware Renewal with grant REEQ/1272/EEI/2005. J. Oliveira, L. Pessoa and D. Coelho also acknowledge support from FCT through a PhD grant. CONCLUSION: Operating a VCSEL device with an off current bellow threshold can lead to high power savings. Although there is a considerable penalty in the eye diagram, transmission of data is still possible at low bit error rates. Decreasing the I off to I th ratio causes an increase of the turn on jitter and, consequently, an increase of the bit error rate. Also, the lower the device threshold current, the lower the jitter. High drive currents help to control the jitter levels but at a lower extent. The jitter is highly dependent on the bit pattern, and especially in the number of trailing zeros, suggesting that a suitable coding scheme for the bit stream could optimize the performance of a zero-biased VCSEL transceiver system. Equalization of the received signal leads to an improvement in the link performance, mitigating the impact of bias free operation. Reducing the large turn-on delay and the resultant eye degeneration is crucial for efficient bias-free transmission of high data rates. Ultimately, turn-on jitter sets a limit on the achievable bit rates to be transmitted under bias-free conditions. 5. Equalization: Simulation results of an equalization filter, with eye diagram before (left) and after equalization (right), for the 1310nm VCSEL device at 4.8Gbit/s. Normal Bias Zero Bias Carrier build up due to bit pattern effects and resulting optical output. 2. Power consumption vs. turn on delay penalty: 1. Introduction: Power consumption in the laser device as a function of I off /I th. Turn on jitter (t on ) probability distribution function for several ratios (η) of carrier life time to bit duration (T) as a function of t on /T. Turn on delay (τ d ) time as a function of I on /I th and I off /I th. Input Current Carrier density Optical power output Bias No bias BER estimate for I on /I th , for I off =0 mA BER estimate for I on /I th , for I off =I th. Turn on delay difference due to bit pattern. ‘dashed’: current into the laser; ‘solid’: laser optical output. 3. BER penalty: 4. Simulation results: 850nm VCSEL 1310nm VCSEL Adaptive Least Mean Squares (LMS) filter, spanning 18 bit periods, step size of 5.10 -4 and a training sequence of 20 bits. The signal Q factor (mean/standard deviation) improved from 15.84dB to 35.47dB at the sample time. Considering BER limited by jitter: Turn on jitter (t on ) depends on turn on delay (τ d ) and number of preceding zeros. Turn on delay depends on I on /I th and I off =I th. By operating the laser device with no bias-current (0 current at the logic 0 stage) a significant power saving can be made regarding the optimum bias current operation mode. However a penalty in the eye diagram shape will occur and, consequently, in the BER. This is because of the turn-on delay increased jitter due to bit-pattern dependent effects and spontaneous emission. Although the eye diagram is distorted, data transmission could be achieved with a bit error rate bellow 10 -9 (50ps jitter).
description
Performance Evaluation of Zero-Biased VCSEL for High Speed Data Transmission. S. Silva a , L. Pessoa a,b , J. Oliveira a,b , D. Coelho a,b , J. C. S. Castro a,b , H. M. Salgado a,b a INESC Porto, Rua Dr. Roberto Frias, 378, 4200 - 465 Porto, Portugal - PowerPoint PPT Presentation
Transcript of Performance Evaluation of Zero-Biased VCSEL for High Speed Data Transmission
S. Silvaa, L. Pessoaa,b, J. Oliveiraa,b, D. Coelhoa,b, J. C. S. Castroa,b, H. M. Salgadoa,b
aINESC Porto, Rua Dr. Roberto Frias, 378, 4200 - 465 Porto, PortugalbFaculty of Engennering, Porto University, Rua Dr. Roberto Frias, S/N, 4200 - 465 Porto, PortugalE-mail: [email protected]
ABSTRACT: In an optical transceiver, the power consumption related to the operation of the laser device takes a significant parcel of the total consumed power. Thus, in optical networks where a large number of transceiver devices are interconnected, e.g. large distributed sensor networks, it is of extremely importance to reduce this power consumption. In this work an analysis and simulation results are presented regarding the operation of a bias-free vertical-cavity surface-emitting laser (VCSEL) device, which is based on a previously developed model. The impact on bit-error rate (BER) of the increased turn-on jitter due to the bit-pattern and spontaneous emission is considered. A method for mitigating the eye-diagram distortion penalty based on the received signal equalization is also illustrated.
ABSTRACT: In an optical transceiver, the power consumption related to the operation of the laser device takes a significant parcel of the total consumed power. Thus, in optical networks where a large number of transceiver devices are interconnected, e.g. large distributed sensor networks, it is of extremely importance to reduce this power consumption. In this work an analysis and simulation results are presented regarding the operation of a bias-free vertical-cavity surface-emitting laser (VCSEL) device, which is based on a previously developed model. The impact on bit-error rate (BER) of the increased turn-on jitter due to the bit-pattern and spontaneous emission is considered. A method for mitigating the eye-diagram distortion penalty based on the received signal equalization is also illustrated.
Performance Evaluation of Zero-Biased VCSEL for High Speed Data Transmission
Acknowledgments: This work was supported in part by EC Framework 7 (FP7) project DAPHNE (www.fp7daphne.eu) – Developing aircraft photonic networks (grant ACP8-GA-2009-233709). We acknowledge funding from FCT and program POCTI/FEDER under the National Plan for Scientific Hardware Renewal with grant REEQ/1272/EEI/2005. J. Oliveira, L. Pessoa and D. Coelho also acknowledge support from FCT through a PhD grant.
Acknowledgments: This work was supported in part by EC Framework 7 (FP7) project DAPHNE (www.fp7daphne.eu) – Developing aircraft photonic networks (grant ACP8-GA-2009-233709). We acknowledge funding from FCT and program POCTI/FEDER under the National Plan for Scientific Hardware Renewal with grant REEQ/1272/EEI/2005. J. Oliveira, L. Pessoa and D. Coelho also acknowledge support from FCT through a PhD grant.
CONCLUSION: Operating a VCSEL device with an off current bellow threshold can lead to high power savings. Although there is a considerable penalty in the eye diagram, transmission of data is still possible at low bit error rates. Decreasing the Ioff to Ith ratio causes an increase of the turn on jitter and, consequently, an increase of the bit error rate. Also, the lower the device threshold current, the lower the jitter. High drive currents help to control the jitter levels but at a lower extent. The jitter is highly dependent on the bit pattern, and especially in the number of trailing zeros, suggesting that a suitable coding scheme for the bit stream could optimize the performance of a zero-biased VCSEL transceiver system. Equalization of the received signal leads to an improvement in the link performance, mitigating the impact of bias free operation. Reducing the large turn-on delay and the resultant eye degeneration is crucial for efficient bias-free transmission of high data rates. Ultimately, turn-on jitter sets a limit on the achievable bit rates to be transmitted under bias-free conditions.
CONCLUSION: Operating a VCSEL device with an off current bellow threshold can lead to high power savings. Although there is a considerable penalty in the eye diagram, transmission of data is still possible at low bit error rates. Decreasing the Ioff to Ith ratio causes an increase of the turn on jitter and, consequently, an increase of the bit error rate. Also, the lower the device threshold current, the lower the jitter. High drive currents help to control the jitter levels but at a lower extent. The jitter is highly dependent on the bit pattern, and especially in the number of trailing zeros, suggesting that a suitable coding scheme for the bit stream could optimize the performance of a zero-biased VCSEL transceiver system. Equalization of the received signal leads to an improvement in the link performance, mitigating the impact of bias free operation. Reducing the large turn-on delay and the resultant eye degeneration is crucial for efficient bias-free transmission of high data rates. Ultimately, turn-on jitter sets a limit on the achievable bit rates to be transmitted under bias-free conditions.
5. Equalization: Simulation results of an equalization filter, with eye diagram before (left) and after equalization (right), for the 1310nm VCSEL device at 4.8Gbit/s. 5. Equalization: Simulation results of an equalization filter, with eye diagram before (left) and after equalization (right), for the 1310nm VCSEL device at 4.8Gbit/s.
Nor
mal
Bia
sZe
ro B
ias
Carr
ier b
uild
up
due
to b
it pa
tter
n eff
ects
and
re
sulti
ng o
ptica
l out
put.
2. Power consumption vs. turn on delay penalty:2. Power consumption vs. turn on delay penalty:1. Introduction:1. Introduction:
Power consumption in the laser device as a function of Ioff/Ith.
Turn on jitter (ton) probability distribution function for several ratios (η) of carrier life time to bit duration (T) as a function of ton/T.
Turn on delay (τd) time as a function of Ion/Ith and Ioff/Ith.
Inpu
t Cur
rent
Carr
ier d
ensi
tyO
ptica
l pow
er
outp
ut
Bias No bias
BER estimate for Ion/Ith , for Ioff=0 mA BER estimate for Ion/Ith , for Ioff=Ith.
Turn on delay difference due to bit pattern. ‘dashed’: current into the laser; ‘solid’: laser optical output.
3. BER penalty:3. BER penalty: 4. Simulation results:4. Simulation results:85
0nm
VCS
EL13
10nm
VCS
EL
Adaptive Least Mean Squares (LMS) filter, spanning 18 bit periods, step size of 5.10-4 and a training sequence of 20 bits.
The signal Q factor (mean/standard deviation) improved from 15.84dB to 35.47dB at the sample time.
Considering BER limited by jitter: Turn on jitter (ton) depends on turn on delay (τd) and number of preceding zeros. Turn on delay depends on Ion/Ith and Ioff=Ith.
By operating the laser device with no bias-current (0 current at the logic 0 stage) a significant power saving can be made regarding the optimum bias current operation mode. However a penalty in the eye diagram shape will occur and, consequently, in the BER. This is because of the turn-on delay increased jitter due to bit-pattern dependent effects and spontaneous emission.
Although the eye diagram is distorted, data transmission could be achieved with a bit error rate bellow 10-9 (50ps jitter).
