Performance Credenza (and other Nucraft Credenzas) Kitchen Aid KUDF204EPA or KUDR204EPA Or GE Monogram ZIDS240HII Custom Drawer Front Installation Instructions (see pg. 5 for GE)

[Rev. G , Aug 6, 2015]

Performance Credenza Kitchen Aid KUDF204EPA or KUDR204EPA Nucraft Furniture Company

2

Kitchen Aid Models (see page 5 for GE)

Before Beginning Installation

• This section for Kitchen Aid models KUDF204EPA and KUDR204EPA only

• Hardware attached will work in along with refrigerator hardware

• The refrigerator instructions work in conjunction with these instructions. Due to the nature and

appearance of the credenza, the size, overlap, and attachment of the custom fronts will be different

then what is given in the refrigerator manufacturer’s instructions.

• Very important to accurately level the both fridge and credenza prior to attaching the drawer fronts

• Products pictured may not match particular installation

• Please read all of the instructions prior to beginning the assembly.

Tools Required For Assembly

• Tools needed:

o Level

o Drill

o Phillips bit

o 3/32” drill bit

o Wonder bar or equivalent crow bar

o Tape measure

o Pencil

o Masking Tape

Hardware

a. “L” Bracket x 4

b. #8 x ½” wood screw x 4

c. Hook & loop strips x 8

d. Mounting brackets included w/ refrigerator, 4 left & 4 right (flat brackets also included, Do not use for this installation)

e. #8 x ½” wood screw included /w refrigerator, black flat head x 16

f. Blue nylon caps x 4, to be placed on fridge glides

Performance Credenza Kitchen Aid KUDF204EPA or KUDR204EPA Nucraft Furniture Company

3

Leveling Case & Refrigerator

1. Place credenza in desired location. Level the case using the eight total glides that are on the case. All glides should contact the floor.

2. Place the blue nylon caps onto the fridge glides and level. This will give the fridge the ability to slide with ease.

3. Slide the refrigerator inside the credenza. It should sit about ¾” from flush & have a gap of 3/16” from top of fridge to bottom of case sub top.

Installing Custom Fronts

1. Keep in mind, to create the look of the credenza, the fronts will be larger than the instructions included with the refrigerator. 2. On the refrigerator, find the four screws on the tops side of the top drawer and the four on the bottom side of the bottom drawer. These will be the ones holding the plastic extrusion into place. Remove the screws furthest to the outside (4 total).

3. Using the “L” bracket included with the Nucraft hardware kit, place the slotted side down over the holes that the screws were removed from. Flush the front of the “L” bracket (single hole side) to the front of the refrigerator door and reattach screws. Do not use the flat brackets included with the refrigerator.

4. Place the hook & loop strips on the refrigerator on the four corners of the steel portion of the refrigerator face, just inside the plastic boarder. Locate the top drawer front. This will be the taller of the two, measuring 16” roughly in height. Place a piece of masking tape ¾” down from the top on the back side of the drawer. Keeping an even gap left to right of the drawer front and flush to the doors pre-mounted already.

“L” bracket at top of top drawer,

please note that for the bottom

drawer, the “L” brackets will be

mounted to the bottom plastic

extrusion. This will give the ability to

create a tighter drawer gap than

Kitchen Aid’s instructions give.

Performance Credenza Kitchen Aid KUDF204EPA or KUDR204EPA Nucraft Furniture Company

4

5. Remove the fridge drawer along with the custom face attached in place (you will find detents on the drawer slides to release the fronts). Draw a line where the fridge front meets the custom front. Remove the custom face. Using the Kitchen Aid instructions for locating the mounting brackets, paying attention to the location up and down of the top set only, base the placement of the brackets from the line that was just drawn and the dimension given in the Kitchen Aid instructions. 6. Locate the slots on the fridge front. Measure the top of the upper most slot to

the top of the lower most slot. Using this dimension, locate the lower mounting brackets on the custom face. (from the top of the bracket that was already attached to locate the top of the bottom bracket) 7. Attach clips so that the tabs are to the outside. 8. Replace fridge drawer back onto fridge.

9. Attach custom faces using the mounting brackets that were just installed. Close drawer and check alignment and flushness of the existing doors on the credenza. Slide unit out and adjust glides if necessary to get the desired alignment. 10. After making sure the face is located desirably with rest of the credenza, pre drill for the “L” bracket and attach screw to lock into place. 11. For the bottom drawer, follow the same steps for the top, except use the bottom of the drawer to locate the front and the hardware. Try to keep flush with the bottom of the case doors, but if needed it can float above or below to help keep an even gap between drawers to match gaps in-between drawers and doors.

Performance Credenza (and other Nucraft Credenzas) GE Monogram ZIDS240HII Custom Drawer Front Installation Instructions

[rev G. Aug 6, 2015]

Performance Credenza GE Monogram ZIDS240HII Custom Drawer Front Nucraft Furniture Company

8

GE Monogram Series

Before Beginning Installation

• This section for GE Monogram ZIDS240HII only

• Hardware attached will work in along with to refrigerator hardware

• Reference the refrigerator instructions work in conjunction with these instructions. Due to the nature

and appearance of the credenza, the size and overlap of the custom fronts will be different then what

is given in the refrigerator manufacturer’s instructions.

• Very important to accurately level both the fridge and credenza prior to attaching the drawer fronts

• Products pictured may not match particular installation

• Please read all of the instructions prior to beginning the assembly.

Tools Required For Assembly

• Tools needed:

o Level

o Drill

o Phillips bit

o 3/32” drill bit

o Wonder bar or equivalent crow bar

o Tape measure

o Pencil

Hardware

a. #8 x 1” wood screw x 8

b. Hook & loop strips x 8

c. Two 23 3/16” x 14 11/16” filler panels

(raw flake core) d. Blue nylon caps x 4, to be placed on

fridge glides

Performance Credenza GE Monogram ZIDS240HII Custom Drawer Front Nucraft Furniture Company

8

Leveling Case & Refrigerator

1. Place credenza in desired location. Level the case using the eight total glides that are on the case. All glides should contact the floor.

2. Place the blue nylon caps onto the fridge glides and level. This will give the fridge the ability to slide with ease. 3. Slide the refrigerator inside the credenza. It should sit about ¾” from flush. Check the levelness again on the refrigerator versus the case and make adjustments if needed.

Installing Custom Fronts

1. Keep in mind, to create the look of the credenza, the fronts will be larger than the instructions included with the refrigerator. 2. Per step 2 of the GE directions (page 6), remove the trim. Insert the custom filler panels Nucraft has supplied. They will be different then the GE directions in the fact that they are single piece with a step to fit into the trim of the refrigerator drawer vs. the plied version they show. Do not attach the custom fronts yet. Reattach the trim. 3. Using rubbing alcohol, clean the front surface of the inserts and back sides of the custom fronts. Apply four of the hook & loop strips to the front of each of the inserts.

4. Locate the top drawer front. This will be the longer of the two, measuring 16 1/8” roughly in height. Keeping an even gap left to right of the drawer front and flush to the top of the doors pre-mounted already on the credenza and sit the front onto the drawer, using the hook & loop stips to hold it into place.

Top Drawer

Performance Credenza GE Monogram ZIDS240HII Custom Drawer Front Nucraft Furniture Company

8

.

5. With the custom fronts stuck to the inserts with the correct door gap spacing, remove the trim. 6. Slide the filler panels out of the trims to gain access to the back. 7. With the custom fronts still stuck in the correct place, screw in the #8 x 1” wood screws through the 4 pre-drills in the filler to the custom front, securing its placement. 8. Slide the filler panel back into the trim making sure that that the pull on the custom front is on the top. Make sure the top of the custom face is in alignment and flush with the existing credenza drawers. If not, the fridge and be pulled out and the glides adjusted.

9. Reinstall the side trims per step 2 in GE instructions. 10. For the bottom drawer, follow the same steps for the top. Try to keep flush with the bottom of the case doors, but if needed it can float above or below to help keep an even gap between drawers to match gaps in-between drawers and doors.