pdfs.findtheneedle.co.ukpdfs.findtheneedle.co.uk/7937-Commercial-and-Industrial-Flooring.pdf ·...

For more information contact sales on 01279 638700

or email [email protected] www.ronacrete.co.uk

Co

mm

ercial and

Ind

ustrial F

loo

ring

Concrete dustproofer Epoxy flooring Polyurethane coatings Floor repair

RonaFloor Concrete Dustproofer

Surface dustproofer and hardener

A world class company

( Formerly Monotect )

Benefits

Easy to apply; no special tools or skills needed

Durable; improved resistance to physical and mild

chemical attack

Dustproofing; binds surface to reduce or eliminate dust

formation

Economical; low cost material and application system

Key Performance Indicators

Can be opened to traffic next day

Dustproofing; binds surface to reduce or eliminate dust

formation

Project references include:

DHL

Britsh Telecom

Courier services

Tesco

Specification Clause

The dustproofer shall be 2 coats (state if more than 2) of

RonaFloor Concrete Dustproofer by Ronacrete Ltd, tel.

+44 (0) 1279 638700. All materials to be applied in

accordance with manufacturers instructions.

Description

RonaFloor Concrete Dustproofer is a liquid surface

hardener and dustproofer for the treatment of new and old

concrete floors. It reduces dusting and wear and enhances

the performance of the floor surface.

RonaFloor Concrete Dustproofer is supplied in concentrated

form and is diluted with clean water before use. It is quick

and easy to apply. Within 48 hours the floor surface is

treated and ready to use.

RonaFloor Concrete Dustproofer is designed for application

on to porous and dusting floors and not those which have a

dense surface finish or are waterproof (eg. contain Ronafix

BBA Approved)

Uses

Use on porous and dusting floors

Internal and external application

Can be used as a surface hardener

Doc Ref: RONC 174.1 20th May 2010

Site Attendance

When on site Ronacrete representatives are able, if asked,

to give a general indication of the correct method of

installing a Ronacrete product. It is important to bear in

mind that Ronacrete Ltd is a manufacturer and not an

application contractor and it is therefore the responsibility of

the contractor and his employer to ensure he is aware of

and implements the correct practices and procedures to

ensure the correct installation of the product and that liability

for its correct installation lies with the contractor and not

with Ronacrete Ltd.

Guarantee

Ronacrete products are guaranteed fit for purpose and of

merchantable quality. Materials are supplied subject to our

standard Terms and Conditions of Sale, available on

request. Additional details on the Insurance Backed

Warranty can be provided by our Technical Department.

Technical Service and Support

Refer to full technical data sheet; this document is a

summary only.

Ronacrete provide free technical advice and support during

design and installation of all systems for flooring, concrete

repair, bonding, bedding and waterproofing. If you need

any further information or a full technical data sheet contact

the Ronacrete Technical Department on +44 (0) 1279 638

700.

More Information

Ronacrete Technical Support:

+44 (0) 1279 638 700 [email protected]

Ronacrete Limited, Ronac House, Flex Meadow, Merring Way, Harlow, Essex, CM19 5TD UK

Tel: +44 (0) 1279 638 700 Fax: +44 (0) 1279 638 701 E-mail: [email protected] Web: www.ronacrete.co.uk

DisclaimerThe information detailed in this leaflet is liable to modification from time to time in the light of experience and of normal product application, and before using, customers areadvised to check with Ronacrete Ltd, quoting the reference number, that they possess the latest issue. Any person or company using the product without first making furtherenquiries as to the suitability of the product for the intended use does so at his own risk, and Ronacrete Ltd can accept no responsibility for the performance of the product,or for any loss or damage arising out of such use. All data shown are typical laboratory results achieved in ideal conditions; site results may differ.

Application

Preparation

Surfaces must be clean, sound and free of loose material.

The floor surface should be clean, free of oil and grease

and dry (slight dampness is acceptable). New concrete

floors should be left for 7-14 days before applying

RonaFloor Concrete Dustproofer.

Remove contamination and lightly abrade surface by wire

brushing or similar to open up the matrix of the floor so that

the RonaFloor Concrete Dustproofer can soak in and react.

Installation

First Coat

Dilute RonaFloor Concrete Dustproofer with between 4 and

8 parts of clean potable water. The dilution depends on the

porosity of the floor – a dense surface will need more

dilution (a greater addition of water) than a porous surface.

For a very porous surface the dilution need only be 4 parts

water.

Pour the diluted material over the floor and sweep in all

directions with a brush, broom or squeegee until no more is

absorbed. Any dry spots should be re-treated. Remove

excess RonaFloor Concrete Dustproofer with a soft broom

or squeegee.

Allow the RonaFloor Concrete Dustproofer to be absorbed

into the concrete leaving a dry surface. A drying period of

12 – 24 hours is normally sufficient. Avoid ponding as this

will prevent the material correctly functioning.

Second coat

Dilute RonaFloor Concrete Dustproofer with 4 parts of clean

potable quality water. Apply as the first coat. Remove

excess and allow to dry. After 12 – 24 hours sweep the

floor to remove surface crystal growth. Sweeping may need

to be repeated for some time whilst the reaction continues.

Packaging

RonaFloor Concrete Dustproofer is supplied in 16.5 and

205 litre containers.

Shelf Life And Storage

Shelf life 9 months. Store in a cool dry place. Protect from

frost.

Health And Safety

Avoid splashing RonaFloor Concrete Dustproofer onto skin

and in eyes. Wash any splashes off with water as soon as

possible. Rubber gloves and eye shields may be worn.

Other Products in the Commercial / Industrial Flooring

Range

RonaFloor Curing Membrane

RonaFloor Epoxy DPM

RonaFloor Epoxy Floor Mortar

RonaFloor Epoxy Floor Mortar Rapid

RonaFloor HB100

RonaFloor HB200

RonaFloor HB Vertical Grade

RonaFloor PU Coating

RonaFloor PU Coating WB

RonaFloor Repair 1 Hour 2-6mm


RonaFloor Repair 1 Hour 25mm+



Description RonaFloor Concrete Dustproofer is a liquid surface hardener and dustproofer for the treatment of new and old concrete floors. It reduces dusting and wear and enhances the performance of the floor surface. It is supplied in concentrated form and diluted with clean water before use. It is quick and easy to apply. Within 48 hours the floor surface is treated and ready to use. RonaFloor Concrete Dustproofer is designed for application on to porous and dusting floors and not those which have a dense surface finish or are waterproof (eg. contain Ronafix or are based on a similar product). The chemicals in RonaFloor Concrete Dustproofer aid the penetration, increasing the depth to which it will reach and react. Its combination and reaction with free lime in the floor screed matrix converts the particles to hard, stable crystals. These crystals are bonded to, and become an integral part of, the floor. Floor Repairs Any floor repairs must first be carried out using suitable mortars from the Ronafix, Monoset, Ronascreed or other range of Ronacrete flooring products. These repairs, provided properly applied, will not need treatment with RonaFloor Concrete Dustproofer. Application Procedure Surfaces must be clean, sound and free of loose material. The floor surface should be clean, free of oil and grease and dry (slight dampness is acceptable). New concrete floors should be left for 7-14 days before applying RonaFloor Concrete Dustproofer. Preparation Remove contamination and lightly abrade surface by wire brushing or similar to open up the matrix of the floor so that the RonaFloor Concrete Dustproofer can soak in and react. First Coat Dilute RonaFloor Concrete Dustproofer with between 4 and 8 parts of clean potable water. The dilution depends on the porosity of the floor – a dense surface will need more dilution (a greater addition of water) than a porous surface. For a very porous surface the dilution need only be 4 parts water. Pour or spray the diluted material over the floor and sweep in all directions with a brush, broom or squeegee until no more is absorbed. Any dry spots should be re-treated. Remove excess RonaFloor Concrete Dustproofer with a soft broom or squeegee. Allow the RonaFloor Concrete Dustproofer to be absorbed into the concrete leaving a dry surface. A drying period of 12 – 24 hours is normally sufficient. Avoid ponding as this will prevent the material correctly functioning. Second coat Dilute RonaFloor Concrete Dustproofer with 4 parts of clean potable quality water. Apply as the first coat. Remove excess and allow to dry. After 12 – 24 hours sweep the floor to remove surface crystal growth. Sweeping may need to be repeated for some time whilst the reaction continues. Coverage Coverage is determined by the porosity of the concrete. For estimating purposes a figure of 12–14m² per litre of diluted RonaFloor Concrete

Dustproofer per coat can be used. Packaging RonaFloor Concrete Dustproofer is supplied in 16.5 and 205 litre containers. Tools and Equipment Tools and equipment should be washed in clean water after use. Painted surfaces, metal and glass should be protected during application. Application Temperatures RonaFloor Concrete Dustproofer should be stored in dry, warehouse conditions out of direct heat and sunlight and applied at temperatures between 5°C and 25°C. Health & Safety Avoid splashing RonaFloor Concrete Dustproofer onto skin and in eyes. Wash any splashes off with water as soon as possible. Rubber gloves and eye shields may be worn. In case of skin contact wash immediately with water. In case of eye contact flush with copious quantities of water and seek medical advice if irritation persists. In case of ingestion do not induce vomiting. Drink plenty of water and seek medical advice. Other Floor Coatings Ronacrete manufacture Ronascreed epoxy, polyurethane and other resin coatings providing chemical resistance, waterproofing, wear resistance and decoration. For full information on their performance and application contact the Ronacrete Technical Department. Site Attendance When on site Ronacrete representatives are able, if asked, to give a general indication of the correct method of installing a Ronacrete product. It is important to bear in mind that Ronacrete Ltd is a manufacturer and not an application contractor and it is therefore the responsibility of the contractor and his employer to ensure he is aware of and implements the correct practices and procedures to ensure the correct installation of the product and that liability for its correct installation lies with the contractor and not with Ronacrete Ltd.

dilution coverage

1st coat 1 litre RonaFloor Concrete Dustproofer diluted with 4 litres water = 5 litres diluted RonaFloor Concrete Dustproofer

5 litres diluted RonaFloor Concrete Dustproofer will cover 5 x 12m2 = 60m2

2nd coat 1 litre RonaFloor Concrete Dustproofer diluted with 4 litres water = 5 litres diluted RonaFloor Concrete Dustproofer

5 litres diluted RonaFloor Concrete Dustproofer will cover 5 x 12m2 = 60m2

Typical guide: 1 litre of undiluted RonaFloor Concrete Dustproofer is sufficient for applying two coats over an area of 30m2 based on average porosity

Estimating Guide

RONL 023 Issue 6 3 June 2010

FEATURES

√ easy to apply; no special tools or skills needed

√ durable; improved resistance to physical and mild chemical attack

√ dustproofing; binds surface to reduce or eliminate dust formation

√ economical; low cost material and application system

The information detailed in this leaflet is liable to modification from time to time in the light of experience and of normal product application, and before using, customers are advised to check with Ronacrete Ltd, quoting the reference number, that they possess the latest issue. Any person or company using the product without first making further enquiries as to the suitability of the product for the intended use does so at his own risk, and Ronacrete Ltd can accept no responsibility for the performance of the product, or for any loss or damage arising out of such use.

Ronacrete Ltd, Ronac House, Flex Meadow, Merring Way, Harlow, Essex CM19 5TD, U.K. Tel: +44 (0)1279 638700 www.ronacrete.co.uk [email protected]

RonaFloor Concrete Dustproofer Surface dustproofer and hardener

Technical Data Sheet

Chemical Synonyms: Silicate of Soda Specific Gravity: @ 20°C: 1.42g/ml

Solubility in Water: Complete Vapour Pressure: As water vapour

Vapour in Density: As water Boiling Point: 100-101°C

Freezing Point: Approximately 0°C pH: 11.6

Risk Phrases: Recommended 38,41. Safety Phrases: Recommended 2, 26, 37/39. Primary Risk: Irritant. S.I. Number: None. CAS Number: 1344-09-8. Hazchem Code: Recommended 2R. UK Customs Number: CUS 23379. Irritating to skin. Risk of serious damage to eyes. Keep out of reach of children. In case of contact with eyes, rinse immediately with plenty of water and seek medical advice. Wear suitable gloves and eye/fact protection. Spillage will effect vegetation. Toxic to aquatic life. An alkaline material which may cause caustic burns to skin and eyes, the danger being greater when hot. Harmful by ingestion, causing internal irritation. Inhalation: Move from exposure. Keep warm and at rest. If there is

respiratory distress give oxygen. If respiration stops or shows signs of falling, apply artificial respiration. Do not use mouth to mouth ventilation. Obtain medical attention urgently.

Skin Contact: Remove contaminated clothing. Wash affected area with copious quantities of water until no soapy feeling remains. Obtain medical attention if irritation persists.

Eye Contact: Speed is essential. The eye should be thoroughly irrigated for not less than 20 minutes with clean water. This prolonged irrigation is of extreme importance and must be done at once otherwise permanent damage will result. Continue irrigation until medical attention can be obtained.

Ingestion: Wash out mouth with water and give sips of water or milk to drink to soothe the affected parts. Obtain medical attention. Do not induce vomiting.

Non-combustible. May generate toxic fumes in a fire. Therefore fire fighters should wear self-contained breathing apparatus and full body protective clothing. Compatible with all standard fire fighting techniques. No special procedures required. Select extinguishing medium appropriate to other materials involved in and/or to the circumstances of the fire. Non-flammable. Contact with certain metals liberates highly flammable hydrogen gas which may form an explosive mixture with air.

Ronacrete Limited Ronac House

Flex Meadow, Merring Way Harlow, Essex CM19 5TD

Tel: 01279 638700 Fax: 01279 638701

HEALTH AND SAFETY INFORMATION RonaFloor Concrete Dustproofer

1. COMPOSITION

2. HAZARDS IDENTIFICATION

3. FIRST AID MEASURES

4. FIRE FIGHTING MEASURES

Small or large spills:- Contain with dry sand and transfer solids to polythene buckets, for neutralisation and disposal. Wash residual liquid to drain with copious amounts of water and possibly detergent. Disposal of hazardous waste in accordance with waste disposal and water authority regulations. Personal Precautions Avoid contact with the product. Ventilate the area to dispel airborne concentrations, protective clothing and (under severe conditions) breathing apparatus should be worn when dealing with spillage. Environmental Precautions If size of spillage warrants and has contaminated water courses, drains or vegetation - advise appropriate authorities. Handling: Exposure by inhalation or skin contact should be minimised

by good industrial hygiene practice. Wear appropriate protective clothing. See exposure control. Safety showers and eye baths should be available in areas where accidental exposure is possible. If freezing occurs, a solution may be reconstituted by warming and agitating with no change in properties. The products should be kept in a closed system away from strong acids.

Storage: Store in well ventilated area away from incompatible chemicals or materials. See stability and reactivity. Store in closed steel or other suitable vessels which prevent the free circulation of air over the surface of the material. If not exposed to the atmosphere solution will keep indefinitely. Drums must be kept closed when not in use. The product absorbs carbon dioxide on exposure to the atmosphere and may even loose water resulting in a formation of a gel, initially turning clouding then eventually solidifying. Avoid exposure to low temperature. Dilute solutions may freeze and ice crystals may separate, rising to the surface. Do not pack into containers which may be attacked or which absorb more moisture from the solution - see materials to avoid.

Hand: Wear impermeable plastic or rubber gloves. Eye: Wear chemical goggles and a dust mask to prevent

inhalation of the product. Eye baths should be provided at places where accidental exposure may be possible.

Skin: Wear impervious boots and poly cotton overalls. Where significant exposure is possible (for example in dealing with spillage or fire), wear imperious body covering. Showers should be provided at places where accidental exposure may occur.

Respiratory: Occupation exposure limits not assessed by HSE or ACGIH. Note: Sodium Hydroxide has an exposure standard of 2mg/m3 (10

minutes twa). It is recommended that exposure to alkalinity calculated as NaOH should be kept below this limit. In the case of mist and spray exposure wear self-contained breathing apparatus.

5. ACCIDENTAL RELEASE MEASURES

6. HANDLING AND STORAGE

7. EXPOSURE CONTROLS/PERSONAL PROTECTION

Appearance: Viscous, aqueous solution Odour: Odourless

Conditions to avoid:- Avoid exposure to atmospheric draughts and low temperature.

Materials to avoid:- Contact with acids will cause the liquid to gel. Absorbs Carbon Dioxide from the air. Ignites and maintains combustion in fluorine. Contact with wood will cause discolouration. Solutions will react with new surfaces of aluminium, zinc and their alloys to liberate hazardous decomposition fumes.

Hazardous Decomposition products: Contact with aluminium, brass, zinc and tin will product highly flammable and explosive hydrogen gas.

Acute effects:- Liquid and mist causes severe irritation and corrosion to skin, eyes, respiratory and digestive tracts. There is little danger of cold solutions causing acute damage to the skin.

Prolonged contact may cause dryness and reddening. Hot solutions may cause chemical damage. Corrosive to eyes and may cause corneal damage.

Inhalation effects respiration and may cause pulmonary oedema.

Ingestion causes systemic dehydration and nausea. Ingestion of large amounts may result it severe abdominal pain, vomiting, diarrhoea, convulsions and collapse.

Chronic effects:- No known hazards are associates with the use of this compound under conditions of good industrial hygiene.

Exotoxicity:- Increase in pH to 10 or more is lethal to aquatic life.

No evidence of bioaccumulation or tainting of seafood. Practical non-toxic to living resources - 96 hrs LC50 = 100-1000mg/l.

DISPOSAL CONSIDERATIONS

Disposal Dangers:- Treat as for spillage. Wear appropriate protective clothing - see accidental release measures. Care should be taken to ensure accidental mixing with acids, in drains is avoided.

Do not attempt to neutralise with strong acids. Neutralisation generates much heat. See disposal methods. Disposal Methods:- Treat as for spillage. See accidental release measures.

Disposal of hazardous waste in accordance with special waste regulations - (control pollution act regulations 1980). First neutralise with careful addition of soda ash (Sodium Carbonate). Carefully mix and then spray with water and transfer the slurry into larger containers. Decant off liquid into another container and neutralise to litmus with 6m Hydrochloric Acid. Wash to drain with plenty of water. Arrange for removal of containers by a licensed contractor, in accordance with waste disposal regulations.

8. PHYSICAL AND CHEMICAL PROPERTIES

9. STABILITY AND REACTIVITY

10. TOXICOLOGICAL INFORMATION

11. ECOLOGICAL INFORMATION

12. DISPOSAL CONSIDERATIONS

Not assigned in the following:- S1 1981/1059 Dangerous substance (conveyance by road in road tankers

and tanker containers) regulations. S1 1984/1244 Classification, packing and labelling of dangerous substance

regulations. S1 1986/1951 Road traffic (carriage of dangerous substance in packages

etc) regulations. Classification: Not classified under the classification, packing and labelling

of dangerous substances. Supply Recommended: Irritant. Conveyance: Not classed in part IA2 of the CPL. Recommended Phrases: Irritating to skin. Risk of serious damage to eyes. Keep out of reach of children.

In case of contact with eyes, rinse immediately with plenty of water and seek medical advice.

Wear suitable gloves and eye/face protection. Voluntary label "splashes can damage eyes". Training Advice:- Dilute Silicate Solutions are a dispersion of molecular

species, indistinguishable from natural dissolved silica. However the pH of most Silicate solutions if above the acceptable limits for direct discharge of sewers or water courses.

Recommended Use:- As a dust proof/hardener for concrete. Data Sources:- HSE Guidance note EH40 occupational exposure limits

(latest edition). ACGIH (threshold limit values and biological exposure indices) 1985-86. Classification, packing and labelling of dangerous substances regulations 1984. IMO reports and studies No 35 (the evaluation of hazards of harmful substances carried by ships) 1989. IMDG code (International Maritime Dangerous Goods Codes) 1990. Control of substances hazardous to health regulations (SI 1988 - 1657).

Control of pollution act 1974. Hazchem list no 6 (Emergency action codes and supplementary information) 1990.

13. TRANSPORT INFORMATION

14. REGULATORY INFORMATION

15. OTHER INFORMATION

Liquid applied epoxy damp proof membrane


( Formerly Ronadeck Epoxy DPM )

Benefits

Reduces project timescale

Can be applied on substrates with a Relative Humidityup to 97%

Easy to apply

Solvent free; low odour

Use prior to application of Ronacrete screeds andcoatings


Meets industry acceptable level of vapour permeability;3gm/m²/day

Excellent dry adhesion to wet concrete

Superb adhesion to wet concrete


Oxford University

Eden Project

Tesco


The damp proof membrane shall be 2 coats of RonaFloorEpoxy DPM by Ronacrete Ltd, tel. +44 (0) 1279 638700. All materials to be applied in accordance withmanufacturers instructions.

Description

RonaFloor Epoxy DPM is a two pack, solvent free, liquidapplied damp proof membrane.

It significantly reduces the passage of water vapour andsuppresses residual moisture. It allows early application ofresin floor finishes including RonaFloor HB100 and HB200and other moisture sensitive floor finishes, even when theRelative Humidity (RH) of the surface is as high as 97%.

Uses

Allows early installation of moisture sensitive finishes

Reduces water and water vapour permeability toacceptable levels

Provides a damp proof membrane prior to applying bondedscreeds including Ronascreed and Ronafix

Substitute for failed preformed membranes


Site Attendance

When on site Ronacrete representatives are able, if asked,to give a general indication of the correct method ofinstalling a Ronacrete product. It is important to bear inmind that Ronacrete Ltd is a manufacturer and not anapplication contractor and it is therefore the responsibility ofthe contractor and his employer to ensure he is aware ofand implements the correct practices and procedures toensure the correct installation of the product and that liabilityfor its correct installation lies with the contractor and notwith Ronacrete Ltd.

Guarantee

Ronacrete products are guaranteed fit for purpose and ofmerchantable quality. Materials are supplied subject to ourstandard Terms and Conditions of Sale, available onrequest. Additional details on the Insurance BackedWarranty can be provided by our Technical Department.


Refer to full technical data sheet; this document is asummary only.

Ronacrete provide free technical advice and support duringdesign and installation of all systems for flooring, concreterepair, bonding, bedding and waterproofing. If you needany further information or a full technical data sheet contactthe Ronacrete Technical Department on +44 (0) 1279 638700.

Technical Data @ 20ºC

Pot Life 30 minutes

Intercoat Period 6-24 hours

Bond Strength > cohesive strength ofconcrete

Water Vapour Permeability <3 gms/m²/day

Coverage: 1st coat 3.5-4.5m²/kg

Coverage: 2nd coat 3.5-4.5m²/kg

More InformationRonacrete Technical Support:+44 (0) 1279 638 700 [email protected]

Ronacrete Limited, Ronac House, Flex Meadow, Merring Way, Harlow, Essex, CM19 5TD UKTel: +44 (0) 1279 638 700 Fax: +44 (0) 1279 638 701 E-mail: [email protected] Web: www.ronacrete.co.uk


Application

Preparation

Prepare the surface by light vacuum shot blasting or similarapproved.

Mixing

Mix with a slow speed drill and spiral mixing paddle(Ronacrete Mixer Attachment E1) for 3-4 minutes.

Installation

Apply the first coat of RonaFloor Epoxy DPM by roller atthe stated coverage. Allow to cure until tack free - typically12 hours @ 20°C.

Within 24 hours of applying the first coat, mix and apply thesecond coat of RonaFloor Epoxy DPM by roller. Within 24hours apply the relevant Ronadeck coating/screed.

If not being immediately covered with a coating or screed,apply a third coat and broadcast 60 mesh dry silica sand into the wet resin at up to 2kg per m² and allow to cure.

Colours

Colour BS ref. given as a guide only

Mid Grey 00 A 05

Brick Red 04 C 39

Clear -

Packaging

RonaFloor HB Vertical Grade is supplied in 5kg packs.


Store in unopened containers in dry warehouse conditionsbetween 10°C and 25°C and protected from direct sunlightand frost. Shelf life is approximately 9 months in theseconditions.

Health And Safety

Protective clothing such as goggles, overalls and gloves isrecommended to prevent any effect from prolonged skincontact, inhalation or ingestion. Refer to Health and SafetyData Sheet.

Other Products in the Commercial / Industrial FlooringRange

Ronacrete Curing MembraneRonaFloor Epoxy Floor MortarRonaFloor Epoxy Floor Mortar RapidRonaFloor Concrete DustprooferRonaFloor HB 100 and 200 CoatingsRonaFloor HB Vertical GradeRonaFloor PU CoatingRonaFloor PU Coating WBRonaFloor Repair 1 Hour 2-6mmRonaFloor Repair 1 Hour 6-50mmRonaFloor Repair 1 Hour 25mm+



Description RonaFloor Epoxy DPM is a two pack, solvent free, liquid applied surface damp proof membrane designed to reduce the passage of water vapour. It allows epoxy resins to be placed onto concrete even when the Relative Humidity (RH) of the concrete is high—up to 97%. Advantages � Reduces water and water vapour permeability � Reduces project timescale � Excellent adhesion to concretes and screeds � Can be applied on substrates with a Relative Humidity up to 97% � Easy to apply � Solvent free, low odour.

SPECIFICATION

Surface Preparation Because RonaFloor Epoxy DPM can be covered with a bonded Ronafix or other Ronacrete modified screed or topping it is essential that the substrate is sound and stable and strong enough to restrain the screed or topping. The instructions given in the appropriate Ronacrete screed specification must therefore be followed. This includes substrate testing to BS 8204 Part 3, 1993. When mechanically abrading surfaces, vacuum blasting rather than scabbling is preferable. A heavy surface profile should be avoided in order to minimise the risk of the RonaFloor Epoxy DPM ponding or not covering high points. When overlaying with an unbonded screed surface preparation requires the substrate to be clean, sound and free of contamination including oil and dirt. If an unbonded screed is being laid on top of RonaFloor Epoxy DPM install a separating layer between the RonaFloor Epoxy DPM and screed to prevent partial adhesion. The substrate should be surface dry before the application of RonaFloor Epoxy DPM. Mixing Pour all of Hardener B into Base A container and mix thoroughly

using a slow speed industrial hand drill and helical spinner. Do not mix by hand or attempt to part mix as performance will be affected. Pour onto surface and apply as described below. Any residual resin remaining on the sides or base of the mixing container should be discarded. Do not use as will not be fully mixed. Application 1. Apply the first coat of RonaFloor Epoxy DPM by squeegee or

roller at the stated coverage. 2. Allow to cure until tack free - typically 12 hours @ 20°C. 3. Within 24 hours of applying the first coat, mix and apply the

second coat of RonaFloor Epoxy DPM by squeegee or roller. 4. Within 24 hours apply the relevant Ronadeck coating/

screed. 5. If not being immediately covered with a coating or screed,

broadcast 60 mesh dry silica sand in to the wet resin at 2kg per m² and allow to cure. Protect dpm with boards or excess sand. Prior to overcoating remove excess sand. Overcoat within 24 hours.

6. In order to prevent the RonaFloor Epoxy DPM being damaged before it is overcoated it should be protected with either boards or excess sand left on the surface. RonaFloor Epoxy DPM can be overlaid with: � Ronadeck EWB water based epoxy floor

coating � Ronadeck HB 100, HB 200 high build solvent free

epoxy floor coatings � Ronadeck SL self smoothing epoxy floor

screed � Ronadeck Epoxy Floor Mortar trowel applied epoxy

floor repair mortar and screed

� most Ronafix, Ronascreed and other Ronacrete cementitious and polymer screeds and toppings

Physical Properties

20°C

Pot life 30 mins

Intercoat period between 1st and 2nd coats

24 hours

Overcoat 2nd coat within 24 hours

ISAT 0.0ml/m²/sec

Bond strength dry >4.0N/mm² wet >1.5N/mm²

In each case failure is in the concrete

Water vapour permeability <3 gms/m²/day

Coverage

First coat 3.5-4.5m²/kg

Second coat 3.5-4.5m²/kg

Coverage is based on smooth, non porous surface.

FEATURES √ damp proof membrane √ epoxy resin based √ liquid applied system √ two coat system √ will receive and restrain bonded screed √ solvent free; low odour SPECIFICATION CLAUSES 1. Damp Proof Membrane The damp proof membrane shall be RonaFloor Epoxy DPM by Ronacrete Ltd, telephone +44 (0) 1279 638700. All materials to be applied in accordance with manufacturers instructions.

SUMMARY APPLICATION PROCEDURE 1. prepare surface 2. mix and apply two coats of RonaFloor Epoxy DPM 3. allow to cure

RonaFloor Epoxy DPM (formerly Ronadeck Epoxy DPM)

Solvent free, liquid applied surface damp proof membrane

Continued on following page………


Site Attendance When on site Ronacrete representatives are able, if asked, to give a general indication of the correct method of installing a Ronacrete product. It is important to bear in mind that Ronacrete Ltd is a manufacturer and not an application contractor and it is therefore the responsibility of the contractor and his employer to ensure he is aware of and implements the correct practices and procedures to ensure the correct installation of the product and that liability for its correct installation lies with the contractor and not with Ronacrete Ltd. Temperature RonaFloor Epoxy DPM should not be applied at material or floor temperatures below 10°C. Above 25°C pot life will be significantly shorter. Temperatures should not fall below 5°C in the 24 hours after application. Cleaning Clean tools with Ronabond EP/PU Cleaner before the material has set. Packaging Available in 4.8kg composite packs, consisting of Base A and Hardener B. Available in clear, brick red or mid grey. Storage and Shelf Life RonaFloor Epoxy DPM should be stored in unopened containers in dry warehouse conditions between 10°C and 25°C and protected from direct sunlight and frost. Shelf life is approximately 9 months in these conditions. Health and Safety First aid - Skin contact, wash immediately with soap and water. Eye contact - wash immediately with copious quantities of water for 10 minutes. Seek immediate medical advice. Ingestion - wash mouth thoroughly with water. Drink water. Do not induce vomiting. Seek immediate medical advice. Spillage - extinguish any ignition sources. Wash small spills away with water, soak large spills with earth or sand; avoid contact; inform authorities of major spillage occurs. Notify Fire Brigade if spillage enters drains. For full health and safety data refer to Ronacrete Technical Department.

RonaFloor Epoxy DPM

Solvent free, liquid applied surface damp proof membrane

RONL 035 Issue 5 29th March 2010



% CAS NO LD50 TLV CLASSIFICATION Bisphenol A/ >50% 25068-36-6 >2000mg/kg oral ND Xi R36/38-46 Epichlorohydrin Epoxy Resin Irritating to skin and eyes. May cause sensitisation in contact with skin. Skin Contact: Wash with soap and water. Eye Contact: Flush with copious quantities of clean water. Use foam, water mist, carbon dioxide or dry powder to extinguish fires. Absorb with earth, sand or non flammable absorbent. Do not eat or drink during use - observe good industrial hygiene. Store in sealed containers at temperatures between 10°C and 30°C. Avoid skin contact - rubber gloves should be worn. Appearance: Blue or buff coloured liquid Odour: Very faint odour pH: Not applicable Boiling point: >250°C Melting point: Not applicable Flash point: >150°C Autoignition Temp °C >450°C Specific Gravity 1.1 Solubility Insoluble



Tel: 01279 638700 Fax: 01279 638701

HEALTH AND SAFETY INFORMATION RonaFloor Epoxy DPM Base Pack A

1. COMPOSITION








Chemical Stability - Yes Incompatibility with other substances - No Skin contact may cause irritation and sensitisation leading to dermatitis. No significant data. Incinerate or dispose of at an approved industrial waste site. Not restricted. Label Classification: Xi - Irritant. Risk Phrases: R36/38 - Irritating to eyes and skin. R43 - May cause sensitisation by skin contact. Safety Phrases: S28 - In case of skin contact wash immediately with plenty of soap and water. S37/39 - Wear suitable protective clothing, gloves and eye/face protection.







% CAS NO LD50 TLV CLASSIFICATION

Propylene Glycol Diamine 15-20 9046-10-0 ND ND C R21/22, 34

Nonyl Phenol 5-10 25154-53-3 ND ND C R22, 34

Benzyl Alcohol 10-15 100-51-6 1230mg/kg oral ND Xn R20/22

Para Tertiary-Butyl Phenol 10-15 98-54-4 ND ND Xi R36,38

Meta Xylene Diamine 20-25 1477-55-0 ND ND C R 20/21, 35

Trimethyl Hexamethylene Diamine 25-30 25513-64-8 ND ND C R35, 22, 43

Causes burns Harmful by inhalation, in contact with skin and if swallowed. May cause sensitisation by skin contact. Skin Contact: Remove contaminated clothing and footwear immediately

unless stuck to skin. Drench the affected skin with running water for 10 minutes or longer if substance is still on skin. Transfer to hospital if there are burns or symptoms of poisoning.

Eye Contact: Bathe the eye with running water for 15 minutes. Transfer

to hospital for specialist examination. Ingestion: Do not induce vomiting. If conscious, give half a litre of

water to drink immediately. Give 1 cup of water to drink every 10 minutes. If unconscious, check for breathing and apply artificial respiration if necessary. If unconscious and breathing OK, place in recovery position. Transfer to hospital as soon as possible.

Inhalation: Remove casualty from exposure ensuring one’s own safety

whilst doing so. If unconscious, check for breathing and apply artificial respiratory if necessary. If unconscious and breathing is OK, place in recovery position. If conscious, ensure the casualty sits or lies down. If breathing becomes bubbly, have the casualty sit and provide oxygen if available. Transfer to hospital as soon as possible.

Extinguishing media: Water spray. Carbon dioxide. Alcohol or polymer foam. Dry

chemical powder. Unsuitable extinguishing media is water in a jet.

Exposure hazards: In combustion emits toxic fumes. In combustion emits toxic

fumes of nitrogen oxides. Also produces carbon oxides.



Tel: 01279 638700 Fax: 01279 638701

HEALTH AND SAFETY INFORMATION RonaFloor Epoxy DPM Base Pack B

1. COMPOSITION




Protection of fire-fighters: Wear self-contained breathing apparatus. Wear protective clothing to prevent contact with skin and eyes.

Personal precautions: Refer to section 7 for personal protection details. Eliminate

all sources of ignition. No smoking. If outside do not approach from downwind.

Environmental precautions: Contain the spillage using bunding. Do not discharge into

drains or rivers. Clean up precautions: Absorb into dry earth or sand. Dispose of as hazardous

waste. Handling requirements: Ensure there is sufficient ventilation of the area. Smoking is

forbidden. Avoid the formation or spread of dust in the air. Avoid the formation or spread of dust in the air. Avoid direct contact with the substance.

Storage conditions: Keep away from sources of ignition. Keep container tightly

closed. Store at ambient temperature. Keep away from food and drink.

Hazardous ingredients: BISPHENOL A WEL (8 hr exposure limit): 5 mg/m³ WEL (15 min exposure limit): 5 mg/m³ Respiratory protection: In poorly ventilated areas use an approved organic vapour

cartridge mask. Hand protection: Protective gloves Eye protection: Safety goggles, face-shield Skin protection: Protective clothing with elasticated cuffs and closed neck.

Boots made of PVC. State: Liquid Colour: Brown Solubility in water: Slightly soluble Viscosity: Dynamic 20….40mPa*s @ 25°C Boiling point/range°C: 135°C Flash point°C: 85.5-DIN51758 Relative density: 1.03g/cm³@20°C-51757 pH: approx: 11 Conditions to avoid: Take necessary action to avoid static electricity discharge. Materials to avoid: Strong acids. Strong bases. Strong oxidising agents. Haz. Decomp. Products: In combustion emits toxic fumes. In combustion emits toxic

fumes of nitrogen oxides. Combustion will generate oxides of carbon.






Hazardous ingredients: BENZYL ALCOHOL IVN RAT LD50 53 mg/kg ORL MUS LD50 1360 mg/kg ORL RAT LD50 1230 mg/kg

• 3-AMINOPROPYLDIMETHYLAMINE ORL RAT LD50 1870 mg/kg SKN RBT LD50 600 µl/kg • 2,4,6-TRIS(DIMETHYLAMINOMETHYL)PHENOL ORL RAT LD50 1200 mg/kg SKN RAT LD50 1280 mg/kg • BISPHENOL A ORL MUS LD50 2400 mg/kg ORL RAT LD50 3250 mg/kg

Route of exposure: Corrosive to the skin of a rabbit Persistence and degradability: Avoid subsoil penetration. Prevent product from entering drains. Do not contaminate surface water. Disposal of packaging: Dispose of in a regulated landfill site or other method for

hazardous or toxic wastes. NB: The user’s attention is drawn to the possible existence of

regional or national regulations regarding disposal. ADR/RID UN no: 2735 ADR Class: 8 Shipping name: AMINES OR POLYAMINES, LIQUID, CORROSIVE N.O.S Labelling: 8 Hazardous ID no: 80 IMDG/IMO UN no: 2735 Class: 8 Packaging group: III EmS: 8-05 Marine pollutant: YES Labelling: 8 IATA/ICAO UN no: 2735 Class: 8 Packaging group: III Packaging instructions: 820 Labelling: 8 Label Classification: C - Corrosive. Risk Phrases: R20/21/22 - Harmful by inhalation, in contact with skin and

if swallowed. R35 - Causes sever burns. R43 – May cause sensitisation by skin contact.






Safety Phrases: S26 - In case of eye contact rinse immediately with water - seek medical advice.

S28 - After skin contact wash with plenty of soap and water. S36/37/39 - Wear suitable protective clothing, gloves and eye/face protection. S45 – In case of accident or if you feel unwell, seek medical advice immediately (show the label where possible)

Risk phrases used in s.2: R20/22 – Harmful by inhalation and if swallowed. R21/22 – Harmful in contact with skin and if swallowed. R34 – Causes burns R43 – May cause sensitisation by skin contact.

R52/53 – Harmful to aquatic organisms, may cause long-term adverse effects in the aquatic environment. R10 – Flammable R22 – Harmful if swallowed. R36/38 – Irritating to eyes and skin. R37 – Irritating to respiratory system. R41 – Risk of serious damage to eyes. R62 – Possible risk of impaired fertility.

Legal disclaimer: The above information is believed to be correct but does not purport to be all inclusive and shall be used only as a guide. This company shall not be held liable for any damage resulting from handling or from contact with the above product.



( Formerly Ronadeck Epoxy Floor Mortar )

Benefits

Resin rich formulation

Good chemical resistance

Easy to clean

Rapid strength development

Impermeable to water

Can be used in conjunction with RonaFloor Epoxy DPM


Meets the requirements of FeRFA Classification Type 8

High compressive strength; in excess of 60N/mm² at 28days


Royal and Sun AllianceLocal Government buildingsFord Motor CompanyLittlewoods


The wearing screed / screed repair shall be RonaFloorEpoxy Floor Mortar by Ronacrete Ltd, tel. +44 (0) 1279638700. The screed shall be laid at a 2-10mm thick (orstate thickness). The primer is to be RonaFloor EpoxyPrimer. All materials to be applied in accordance withmanufacturers instructions.

Description

RonaFloor Epoxy Floor Mortar is a high performance epoxyresin screed for repairing existing floors and providing newwearing surfaces. Its formulation allows thin sectionapplication from 2mm. It is suitable for forming coves,skirtings and upstands.

It offers good mechanical resistance and will resist attackfrom most industrial chemicals including acids, alkalis, oils,fats, solvents and foodstuffs. Surfaces laid or repaired withRonaFloor Epoxy Floor Mortar can be accessed by foottraffic after 10-12 hours and by heavy loads after 16 hours(at 20°C). RonaFloor Epoxy Floor Mortar has beendesigned for ease of use and practicality of application.

Uses

High strength thin bonded patch repairs and resurfacing inheavy duty high demand flooring applications

Factories, warehouses, ramps, bunds, chemical and foodprocessing areas

Suitable for forming and repairing screeds to meet theHeavy Duty category of BS8204: Part 6: 2001


Site Attendance


Guarantee



Pot Life 30-45 minutes

Foot Traffic 10-12 hours

Full Traffic 16 hours

Full Chemical Resistance 6 days

Compressive Strength 70N/mm² at 28 days

Flexural Strength 30N/mm² at 28 days

Yield 96 x 25kg packs per m³

480 x 5kg packs per m³




Application

Preparation

Mechanically prepare substrate in accordance with BS8204:Part 6: 2001. Provide structurally sound and clean substrateto receive high strength screed.

Mixing

Mix using a forced action mixer. If using a drill and paddlemixer use Ronacrete Mixer Attachment C2.

Installation

Trowel apply screed onto tacky primer. Finish with float ortrowel.

Packaging

RonaFloor Epoxy Floor Mortar is supplied in 5kg and 25kgpacks.

RonaFloor Epoxy Primer is supplied in 2.25kg and 4.5kgpacks.


Shelf life 9 months. Store in a cool dry place. Protect fromfrost.

Health And Safety



Ronacrete Curing MembraneRonaFloor Concrete DustprooferRonaFloor Epoxy DPMRonaFloor HB100RonaFloor HB200RonaFloor HB Vertical GradeRonaFloor PU CoatingRonaFloor PU Coating WBRonaFloor Repair 1 Hour 2-6mmRonaFloor Repair 1 Hour 6-50mmRonaFloor Repair 1 Hour 25mm+



Description RonaFloor Epoxy Floor Mortar Standard and Rapid are high performance epoxy resin mortars for repairing existing floors and providing new wearing surfaces in light and heavy traffic areas. Its formulation allows thin section application down to 2mm and feather edge. RonaFloor Epoxy Floor Mortar offers good mechanical resistance and will resist attack from most industrial chemicals including acids, alkalis, oils, fats, solvents and foodstuffs. RonaFloor Epoxy Floor Mortar Standard RonaFloor Epoxy Floor Mortar Standard can be used to lay floor screeds and to repair floors. Surfaces laid or repaired with RonaFloor Epoxy Floor Mortar Standard can be accessed by foot traffic after 10-12 hours and by heavy loads after 16 hours (at 20°C). RonaFloor Epoxy Floor Mortar Rapid The rapid strength gain properties of RonaFloor Epoxy Floor Mortar Rapid shortens the pot life and working time of the mixed mortar. Whilst it is suitable for floor repairs its short pot life makes it unsuitable for laying floor screeds. Surfaces repaired with RonaFloor Epoxy Floor Mortar Rapid can be accessed by foot and heavy traffic after 4 hours (at 20°C). Advantages

� Good workability for small and large areas

� Can be feather edged

� Good surface finish

� Resistant to mechanical and chemical attack

� Can be left with a slip resistant finish

� Rapid grade can be trafficked after only 4 hours at 20°C

� Seven colours available Mixing RonaFloor Epoxy Floor Mortar Standard and Rapid are supplied as a three component materials in a plastic container. Remove all materials from the container; pour the base and activator into the container and mix. When thoroughly mixed slowly add the supplied aggregate and mix until homogeneous. The product has been designed to be used as a full pack; do not part mix. Mix with a drill and paddle or similar. Mixing time should be approximately 3-4 minutes by machine and 5-6 minutes by hand. The Standard grade will have

a pot life of approximately 30-45 minutes at 20°C; Rapid grade has a pot life of 15 minutes at 20°C. Application Place the mixed material onto the wet primer. If the primer has dried it must be reapplied. Spread and smooth the material with either a wood or steel float. Working the material will bring resin to the surface to allow it to be finished; avoid overworking the surface. Day joints should be at 90° to the floor. Feather edging can be used at ramps and doorways etc but is not recommended for day joints. RonaFloor Epoxy Floor Mortar should not be used at temperatures lower than 10°C. Ideally store materials at 15°C to 20°C for 24 hours before use. Working time - Rapid grade Note that the working time of the Rapid grade is limited to only 15 minutes at a material, air and substrate temperature of 20oC (Standard 30 - 45 minutes) and within this time it must be transported to the point of application, laid and finished. After this time the mortar will lose workability. Working Temperatures RonaFloor Epoxy Floor Mortar Standard or Rapid can be used in most weather conditions and in a wide temperature range, typically from +5°C to 25°C The minimum working temperature is +5oC. Note that at high ambient temperatures the working time of the mix will be reduced; it will be increased at lower temperatures. Ideally store materials between 10oC and 20oC before use. In areas exposed to sunlight, the substrate can be hotter than the air and material temperature. Work must stop if material, air or substrate temperature exceeds 25oC. “Feather edging” Whilst it is possible to lay the mortar very thin and to a feather edge, feather edged repairs are less durable than thicker repairs and it is always recommended that the repair area is cut out to allow not less than 2mm—3mm to be applied. Colour Range RonaFloor Epoxy Floor Mortar is available in grey (standard colour), red, green, brown, blue, yellow and charcoal. Note that colour consistency cannot be guaranteed and differences in colour and shading should be expected. Cleaning Clean all tools and equipment immediately with RonaFloor Epoxy Floor Mortar Cleaner. RonaFloor Epoxy Floor Mortar is a hardwearing, durable, epoxy floor

screed and repair mortar for medium and heavy duty industrial and commercial floors. Its design provides texture and grip for dry and wet environments. As with all flooring of this type there is a compromise between slip resistance and ease of cleaning. In areas where ease of cleaning and hygiene are important such as laboratories, kitchens and food processing areas, RonaFloor Epoxy Floor Mortar may not be suitable and the Ronacrete Technical Department should be consulted. To ensure the suitability of any product, a sample area should be laid and its performance and ease of cleaning assessed. For additional information please refer to FeRFA publications on the selection

and cleaning of resin flooring.

Health and Safety Wear protective clothing to protect skin and eyes. In case of skin contact wash with soap and water. In case of eye contact flush immediately with clean water. In case of ingestion drink milk or water, do not induce vomiting. Seek medical attention. This product contains no volatile solvents and should cause no problems due to inhalation during use. Although non-flammable RonaFloor Epoxy Floor Mortar will burn in the event of a fire. Extinguish with foam, water mist, CO2 or dry powder. Breathing apparatus should be worn. Storage/Shelf Life RonaFloor Epoxy Floor Mortar should be stored unopened between 10°C and 20°C in dry warehouse conditions and out of direct sunlight. In these conditions shelf life is approximately 12 months. Site Attendance When on site Ronacrete representatives are able, if asked, to give a general indication of the correct method of installing a Ronacrete product. It is important to bear in mind that Ronacrete Ltd is a manufacturer and not an application contractor and it is therefore the responsibility of the contractor

FEATURES

√ Epoxy resin screed and floor repair mortars

√ Can be laid very thin and to a feather edge

√ Suitable for light and heavy duty floors

√ Smooth surface finish

√ Rapid grade: foot traffic after 4 hours, heavy traffic after 4 hours

√ Standard grade: foot traffic after 10 hours, heavy traffic 16 hours SPECIFICATION CLAUSES 1. Floor Screed / Floor Repair - Standard Set The floor screed or floor repair shall be RonaFloor Epoxy Floor Mortar Standard by Ronacrete Ltd, telephone +44 (0) 1279 638700. The primer is to be RonaFloor Epoxy Floor Mortar Primer. All materials to be applied in accordance with manufacturers instructions. The screed or repair can be opened to foot / heavy traffic after 10 / 16 hours at 20oC. 2. Floor Repair - Rapid Set The floor repair shall be RonaFloor Epoxy Floor Mortar Rapid by Ronacrete Ltd, telephone +44 (0) 1279 638700. The primer is to be RonaFloor Epoxy Floor Mortar Primer. All materials to be applied in accordance with manufacturers instructions. The repair can be opened to foot / heavy traffic after 4 hours at 20oC.

SUMMARY APPLICATION PROCEDURE 1. prepare surface 2. Apply primer 3. apply RonaFloor Epoxy Floor Mortar Standard or Rapid 4. cure and protect 5. optionally apply epoxy RonaFloor epoxy floor coating


RonaFloor Epoxy Floor Mortar Epoxy floor screed and floor repair mortar


RONL067 Issue 7 29 March 2010

Technical Summary at 20ºC

volume solids 100%

min/max thickness Feather edge/50mm

minimum / maximum application temperature (air, material and substrate)

10°C / 25oC

pot life (approx). 30-45 minutes

hard dry/foot traffic 10-12 hours

full traffic 16 hours

shelf life 12 months unopened

full chemical resistance 6 days

compressive strength 49N/mm² at 1 day 70N/mm² at 28 days

flexural strength 30N/mm² at 28 days

100%

Feather edge/50mm

10°C / 25oC

12—15 minutes

3 - 4 hours

4 hours

12 months unopened

6 days

26N/mm² at 4 hours 84N/mm² at 28 days

25N/mm² at 24 hours

Standard Grade Rapid Grade

Packaging and Coverage (approx.)

RonaFloor Epoxy Floor Mortar Standard and Rapid

5kg 0.35m² @ 6mm


25kg 1.75m² @ 6mm

RonaFloor Epoxy Floor Mortar Primer 2.25kg 12.5m²

RonaFloor Epoxy Floor Mortar Primer 4.5kg 25m²

Coverage rates are based on smooth, flat, non-porous surfaces

Chemical Resistance Chart

Chemical Chemical Resistance


Tap water R 16% Bleach S

Xylene S Animal fats R

50% Sodium Hydroxide

S 10% Lactic Acid S

25% Ammonia S 10% Nitric Acid S

50% Sulphuric Acid

S High Octane Petrol

R

30% Hydrochloric Acid

S Acetone NR

30% Chromic Acid R Engine Oil R

10% Acetic Acid S Methanol S

Skydrol S Toluene S

Teepol 10% R 50% Phosphoric Acid

S

White spirit R 50% Sugar solution

S

NR - Not recommended R - Resistant S - Resistant to spillage only

The information detailed in this leaflet is liable to modification from time to time in the light of experience and of normal product application, and before using, customers are advised to check with Ronacrete Ltd, quoting the reference number, that they possess the latest issue. Any person or company using the product without first making further enquiries as to the suitability of the product for the intended use does so at his own risk, and Ronacrete Ltd can accept no responsibility for the performance of the product, or for any loss or damage arising out of such use. All goods supplied subject tour Terms and Conditions of Sales; see www.ronacrete.co.uk.



A 3 pack system comprising resin, hardener and aggregate which are supplied in separate containers to be mixed together at the site of application. % By weight CAS No Hazard R-phrases Symbols

Composition of Resin:

Epoxy resin 5-20% 68609-97-2 Xi, N R36/38,43,51/53

Epoxy resin 10-40% 9003-36-5 Xi, N R36/38,43,51/53

Epoxy resin 10-40% 25068-38-6 Xi, N R36/38,43,51/53

Non-toxic additives < 1%

Epoxide derivatives 4-10% Xi, N R36/R38-43,51,53

Combination of high bonding

solvents <1% R37-43,50-53

Composition of Hardener:

Benzyl Alcohol 25-50% 100-51-6 Xn R20,22

Isophoronediamine 10-30% 2855-13-2 C R21,22,34,43

4-Tert-butylphenol <10% 98-54-4 Xi R36,37,38,42,43

Nonylphenol <5 25154-52-3 C, N R22,34,50,53

n-Xylenediamine 10-25% 1477-55-0 C R20/21,31,45

Composition of Aggregate: Natural aggregates, which are produced from naturally occurring rock and gravel deposits and consist of combinations of various minerals including silica. Resin: - Hazard Designation i Irritant N Dangerous to the environment

- Information pertaining to particular dangers for man and environment.

R36/38 Irritating to eyes and skin R51/53 Toxic to aquatic organisms, may cause long-term adverse

effects in the aquatic environment. R43 May cause sensitisation by skin contact. Contains epoxy constituents. Hardener: - Hazard Designation C Corrosive

- Information pertaining to particular dangers for man and environment

R20/21/22 Harmful by inhalation, in contact with skin and if swallowed R34 Causes burns R43 May cause sensitisation by skin contact. Aggregate: Dust inhaled over a prolonged period can be hazardous to health. When the respirable dust contains silica, the risks are increased. Advice on the silica content on individual aggregates is available on request.



Tel: 01279 638700 Fax: 01279 638701

HEALTH AND SAFETY INFORMATION RonaFloor Epoxy Floor Mortar

1. COMPOSITION


Eye Contact: Rinse immediately with water, continuing for 15 minutes. Seek medical attention. Skin Contact: Rinse immediately with plenty of soap and water. Remove contaminated clothing.

In case of persistent irritation, or if a rash develops, seek medical attention.

Inhalation: Remove the affected person to fresh air and allow to rest. In case of breathing difficulty, or distress, seek medical attention.

Ingestion: Immediately rinse mouth with water and seek medical attention. If this is not immediately available, drink 1 or 2 pints of water.

Aggregate: Eye Contact: Wash with copious amounts of water and seek medical

advice. Skin Contact: Wash with water. Inhalation: Remove from exposure to a ventilated area. Ingestion: Remove from exposure to a ventilated area. Special hazards: If involved in a fire, may generate noxious or toxic vapours. Protective equipment: Wear full protective suit. Fire fighters wear self-contained breathing apparatus. Extinguishing agents: Foam, dry powder, CO2 or water spray. Aggregate: None needed. Personal precautions: Wear full protective clothing when dealing with a spillage. Keep unprotected persons away. Environmental precautions: Prevent from entering sewer system, surface water, or soil. Methods for cleaning up: Absorb with earth, sand or other absorbent materials.

Dispose of contaminated material as waste according to item 13.

Aggregate: Personal precautions: In the event of a spillage avoid breathing dust. Wear dust

mask/respirator and goggles as per section 8. Environmental precautions: Releasing the dust into the environment does not constitute

a significant hazard. Methods for cleaning up: Vacuum cleaning, dampen area avoid brushing dry dust

where possible. - Handling: - Information for safe handling.

Ensure good ventilation/exhaustion at the work place. Wear goggles or a face shield, impervious gloves and protective clothing.

- Information about protection against explosion and fires. No special measures required. - Storage: - Requirements to be met by storerooms and containers. Prevent any penetration into the ground. - Further information about storage conditions. Store in cool, dry conditions in well-sealed containers.





Aggregate: The product should be stored in such a way as to reduce airborne dust. When bagged the material should be kept dry and palletised. During application: Wear goggles or a face shield, impervious gloves and

protective clothing. Apply in a well-ventilated area. Aggregate: Occupational exposure levels. Total inhalable dust 10mg/m3 OES Respirable dust 4mg/m3 OES Respirable dust silica 0.3mg/m3 Wear goggles or a face shield, abrasive resistant gloves and protective clothing. Apply in a well-ventilated area. Resin: Physical state: liquid resin. Colour: pale yellow, slightly milky. Odour: weak odour. Vapour pressure: <0.01kPa at 20@C. Boiling point: >200@C. Flash point: >250@C. Density: 1.10 at 20oC. Solubility (water) insoluble. Viscosity: 700cPs at 25oC. Hardener: Physical state: liquid. Colour: pale yellow. Odour: amine-like. Vapour pressure: 0.28mbar at 20oC. Boiling point: >200°C. Flash point: >100@C. Density: 1.05g/cm3 at 20@C. Solubility: slightly soluble. Viscosity: 400cPs at 25oC. Aggregate: Odourless solid particles of crushed stone gravel with

various colours. Chemical properties not applicable. Resin: May react exothermally with amines and mercaptans, also

with acids. In case of a fire, carbon monoxide, carbon dioxide and other harmful gases may be formed.

Hardener: Reacts exothermally with acids. Liberates ammonia when heated. In case of a fire, toxic fumes of nitrogen oxides, amines and carbon monoxide may be formed. Nitrogen oxide can react with water vapours to form corrosive nitric acid.

Aggregate: Not applicable.




Resin: LD50 oral, rat: >5000mg/kg.

Epoxy resins such as contained in this product have been shown to cause irritation in humans on skin and eyes. Sensitisation by skin contact may also occur.

Hardener: LD50 oral, rat: >1620mg/kg. The amine/diamine constituents of this product are irritant to skin and mucous membranes, irritant to eyes, and may cause sensitisation.

Aggregate: May cause transient irritation to eyes. Inhalation of large quantities of respirable silica may lead to progressive lung damage. Chronic exposure to high levels of silica may cause progressive silicosis.

Environmental precautions: Prevent from entering sewer system, surface water or soil. Aggregate: No adverse effect foreseen. DISPOSAL CONSIDERATIONS Waste: Remove according to local authority recommendations, e.g.

Convey to a licensed incinerator. Do not re-use containers.

Aggregate: Non hazardous. Resin: Land Transport ADR/RID (Cross-border) ADR/RID Class: 9 Various dangerous materials and objects. Number/Letter: 11c) Hazard Index Number: 90 Substance Index Number: 3082 Designation of goods: 3082 Maritime transport IMDG IMDG Class: 9 Page: 9082 UN Number: 3082 Packaging group: III EMS Number: - MFAG: - Correct technical name: Environmentally hazardous substance, liquid, n.o.s. (epoxide

derivative) Air transport ICAO-TI and IATA-DGR ICAO/IATA Class: 9 UN/ID Number: 3082 Packaging group: III Correct technical name: Environmentally hazardous substance, liquid, n.o.s. (epoxide

derivative) Transport/Additional Information No dangerous goods according to international transport regulations. Hardener: Land transport ADR/RID (Cross-border) ADR/RID Class: 8 Corrosive materials. Number/Letter: 53c) Hazard index number: 80





Substance index number: 2735 Label: 8 Designation of goods: Polyamines, liquid, corrosive, n.o.s. (isophoronediamine) Maritime transport IMDG IMDG Class 8 Page 8109-2 UN Number: 2735 Packaging group: III MFAG: 320 Marine pollutant: - Correct technical name: Polyamines, liquid, corrosive, n.o.s. (isophoronediamine) Air transport ICAO-TI and IATA-DGR ICAO/IATA Class: 8 UN/ID Number: 2735 Packaging group: III Correct technical name: Polyamines, liquid, corrosive, n.o.s. (isophoronediamine) Aggregate: Non hazardous, no transport labelling required. Resin: Hazard labels: Xi Irritant. N Dangerous for the environment. R-phrases: 51/53 toxic to aquatic organisms. R36/38 Irritating to eyes and skin. R43 May cause sensitisation by skin contact. S-phrases: S26 In case of contact with eyes, rinse immediately with

plenty of water and seek medical advice. S28 After contact with skin, wash immediately with plenty of soap and water.

S36 Wear suitable protective clothing. S61 Avoid release to environment. Refer to special instructions.

Hardener: Hazard labels: C Corrosive. R-phrases: R20/21/22 Harmful by inhalation, in contact with skin and if

swallowed. R34/R35 Causes burns. R43 May cause sensitisation by skin contact. S-phrases: S26 In case of contact with eyes, rinse immediately with

plenty of water and seek medical advice. S28 After contact with skin, wash immediately with plenty of soap and water. S36/37/39 Wear suitable protective clothing, gloves and eye/face protection. S45 In case of accident or if you feel unwell, seek medical advice immediately.

Aggregate: Not classified as dangerous for supply within the UK. The above information and advice are given when the material is used as intended. If purchasing on behalf of a third party, it is your duty to take all necessary steps to secure that the person handling or using the material is provided with the information in the data sheet. All the foregoing information should be regarded as being applicable to the finished paint as well as to the individual components.



( Formerly Ronadeck Epoxy Floor Mortar Rapid )

Rapid strength gain trowel applied epoxy floor screed


Benefits

Rapid strength gain

Foot traffic after 3 hours; heavy traffic after 4 hours


Easy to clean

Impermeable to water




Rapid strength gain; 23N/mm² at 4 hours


Royal and Sun AllianceLocal Government buildingsFord Motor CompanyLittlewoods


The wearing screed / screed repair shall be RonaFloorEpoxy Floor Mortar Rapid by Ronacrete Ltd, tel. +44 (0)1279 638700. The screed shall be laid at a 2-10mm thick(or state thickness). The primer is to be RonaFloor EpoxyFloor Mortar Primer. All materials to be applied inaccordance with manufacturers instructions.

Description

RonaFloor Epoxy Floor Mortar Rapid is a rapid version ofRonadeck Epoxy Floor Mortar, a rapid strength gain highperformance epoxy resin screed for repairing existing floorsand providing new wearing surfaces. Its formulation allowsthin section application from 2mm. It is suitable for formingcoves, skirtings and upstands.

It offers good mechanical resistance and will resist attackfrom most industrial chemicals including acids, alkalis, oils,fats, solvents and foodstuffs. Surfaces laid or repaired withRonaFloor Epoxy Floor Mortar can be accessed by foottraffic after only 3 hours and by heavy loads after 4 hours(at 20°C). RonaFloor Epoxy Floor Mortar has beendesigned for ease of use and practicality of application.

Uses

Emergency and rapid thin bonded patch repairs andresurfacing in heavy duty high demand flooring applications

Factories, warehouses, ramps, bunds, chemical and foodprocessing areas

Suitable for forming and repairing screeds to meet theHeavy Duty category of BS8204: Part 6: 2001


Site Attendance


Guarantee







Foot Traffic 3-4 hours

Full Traffic 4 hours

Full Chemical Resistance 6 days

Compressive Strength 23N/mm² at 4 hours

Flexural Strength 30N/mm² at 24 hours

Yield 96 x 25kg packs per m³

480 x 5kg packs per m³




Application

Preparation

Mechanically prepare substrate in accordance with BS8204:Part 6: 2001. Provide structurally sound and clean substrateto receive high strength screed.

Mixing

Mix using a forced action mixer. If using a drill and paddlemixer use Ronacrete Mixer Attachment C2.

Installation

Trowel apply screed onto tacky primer. Finish with float ortrowel.

Packaging

RonaFloor Epoxy Floor Mortar is supplied in 5kg and 25kgpacks.

RonaFloor Epoxy Floor Primer is supplied in 2.25kg and4.5kg packs.



Health And Safety



Ronacrete Curing MembraneRonaFloor Concrete DustprooferRonaFloor Epoxy DPMRonaFloor HB100RonaFloor HB200RonaFloor HB Vertical GradeRonaFloor PU CoatingRonaFloor PU Coating WBRonaFloor Repair 1 Hour 2-6mmRonaFloor Repair 1 Hour 6-50mmRonaFloor Repair 1 Hour 25mm+



Description RonaFloor Epoxy Floor Mortar Standard and Rapid are high performance epoxy resin mortars for repairing existing floors and providing new wearing surfaces in light and heavy traffic areas. Its formulation allows thin section application down to 2mm and feather edge. RonaFloor Epoxy Floor Mortar offers good mechanical resistance and will resist attack from most industrial chemicals including acids, alkalis, oils, fats, solvents and foodstuffs. RonaFloor Epoxy Floor Mortar Standard RonaFloor Epoxy Floor Mortar Standard can be used to lay floor screeds and to repair floors. Surfaces laid or repaired with RonaFloor Epoxy Floor Mortar Standard can be accessed by foot traffic after 10-12 hours and by heavy loads after 16 hours (at 20°C). RonaFloor Epoxy Floor Mortar Rapid The rapid strength gain properties of RonaFloor Epoxy Floor Mortar Rapid shortens the pot life and working time of the mixed mortar. Whilst it is suitable for floor repairs its short pot life makes it unsuitable for laying floor screeds. Surfaces repaired with RonaFloor Epoxy Floor Mortar Rapid can be accessed by foot and heavy traffic after 4 hours (at 20°C). Advantages

� Good workability for small and large areas

� Can be feather edged

� Good surface finish

� Resistant to mechanical and chemical attack

� Can be left with a slip resistant finish

� Rapid grade can be trafficked after only 4 hours at 20°C

� Seven colours available Mixing RonaFloor Epoxy Floor Mortar Standard and Rapid are supplied as a three component materials in a plastic container. Remove all materials from the container; pour the base and activator into the container and mix. When thoroughly mixed slowly add the supplied aggregate and mix until homogeneous. The product has been designed to be used as a full pack; do not part mix. Mix with a drill and paddle or similar. Mixing time should be approximately 3-4 minutes by machine and 5-6 minutes by hand. The Standard grade will have

a pot life of approximately 30-45 minutes at 20°C; Rapid grade has a pot life of 15 minutes at 20°C. Application Place the mixed material onto the wet primer. If the primer has dried it must be reapplied. Spread and smooth the material with either a wood or steel float. Working the material will bring resin to the surface to allow it to be finished; avoid overworking the surface. Day joints should be at 90° to the floor. Feather edging can be used at ramps and doorways etc but is not recommended for day joints. RonaFloor Epoxy Floor Mortar should not be used at temperatures lower than 10°C. Ideally store materials at 15°C to 20°C for 24 hours before use. Working time - Rapid grade Note that the working time of the Rapid grade is limited to only 15 minutes at a material, air and substrate temperature of 20oC (Standard 30 - 45 minutes) and within this time it must be transported to the point of application, laid and finished. After this time the mortar will lose workability. Working Temperatures RonaFloor Epoxy Floor Mortar Standard or Rapid can be used in most weather conditions and in a wide temperature range, typically from +5°C to 25°C The minimum working temperature is +5oC. Note that at high ambient temperatures the working time of the mix will be reduced; it will be increased at lower temperatures. Ideally store materials between 10oC and 20oC before use. In areas exposed to sunlight, the substrate can be hotter than the air and material temperature. Work must stop if material, air or substrate temperature exceeds 25oC. “Feather edging” Whilst it is possible to lay the mortar very thin and to a feather edge, feather edged repairs are less durable than thicker repairs and it is always recommended that the repair area is cut out to allow not less than 2mm—3mm to be applied. Colour Range RonaFloor Epoxy Floor Mortar is available in grey (standard colour), red, green, brown, blue, yellow and charcoal. Note that colour consistency cannot be guaranteed and differences in colour and shading should be expected. Cleaning Clean all tools and equipment immediately with RonaFloor Epoxy Floor Mortar Cleaner. RonaFloor Epoxy Floor Mortar is a hardwearing, durable, epoxy floor

screed and repair mortar for medium and heavy duty industrial and commercial floors. Its design provides texture and grip for dry and wet environments. As with all flooring of this type there is a compromise between slip resistance and ease of cleaning. In areas where ease of cleaning and hygiene are important such as laboratories, kitchens and food processing areas, RonaFloor Epoxy Floor Mortar may not be suitable and the Ronacrete Technical Department should be consulted. To ensure the suitability of any product, a sample area should be laid and its performance and ease of cleaning assessed. For additional information please refer to FeRFA publications on the selection

and cleaning of resin flooring.

Health and Safety Wear protective clothing to protect skin and eyes. In case of skin contact wash with soap and water. In case of eye contact flush immediately with clean water. In case of ingestion drink milk or water, do not induce vomiting. Seek medical attention. This product contains no volatile solvents and should cause no problems due to inhalation during use. Although non-flammable RonaFloor Epoxy Floor Mortar will burn in the event of a fire. Extinguish with foam, water mist, CO2 or dry powder. Breathing apparatus should be worn. Storage/Shelf Life RonaFloor Epoxy Floor Mortar should be stored unopened between 10°C and 20°C in dry warehouse conditions and out of direct sunlight. In these conditions shelf life is approximately 12 months. Site Attendance When on site Ronacrete representatives are able, if asked, to give a general indication of the correct method of installing a Ronacrete product. It is important to bear in mind that Ronacrete Ltd is a manufacturer and not an application contractor and it is therefore the responsibility of the contractor

FEATURES

√ Epoxy resin screed and floor repair mortars

√ Can be laid very thin and to a feather edge

√ Suitable for light and heavy duty floors

√ Smooth surface finish

√ Rapid grade: foot traffic after 4 hours, heavy traffic after 4 hours

√ Standard grade: foot traffic after 10 hours, heavy traffic 16 hours SPECIFICATION CLAUSES 1. Floor Screed / Floor Repair - Standard Set The floor screed or floor repair shall be RonaFloor Epoxy Floor Mortar Standard by Ronacrete Ltd, telephone +44 (0) 1279 638700. The primer is to be RonaFloor Epoxy Floor Mortar Primer. All materials to be applied in accordance with manufacturers instructions. The screed or repair can be opened to foot / heavy traffic after 10 / 16 hours at 20oC. 2. Floor Repair - Rapid Set The floor repair shall be RonaFloor Epoxy Floor Mortar Rapid by Ronacrete Ltd, telephone +44 (0) 1279 638700. The primer is to be RonaFloor Epoxy Floor Mortar Primer. All materials to be applied in accordance with manufacturers instructions. The repair can be opened to foot / heavy traffic after 4 hours at 20oC.

SUMMARY APPLICATION PROCEDURE 1. prepare surface 2. Apply primer 3. apply RonaFloor Epoxy Floor Mortar Standard or Rapid 4. cure and protect 5. optionally apply epoxy RonaFloor epoxy floor coating


RonaFloor Epoxy Floor Mortar Epoxy floor screed and floor repair mortar


RONL067 Issue 7 29 March 2010

Technical Summary at 20ºC

volume solids 100%

min/max thickness Feather edge/50mm

minimum / maximum application temperature (air, material and substrate)

10°C / 25oC

pot life (approx). 30-45 minutes

hard dry/foot traffic 10-12 hours

full traffic 16 hours

shelf life 12 months unopened

full chemical resistance 6 days

compressive strength 49N/mm² at 1 day 70N/mm² at 28 days

flexural strength 30N/mm² at 28 days

100%

Feather edge/50mm

10°C / 25oC

12—15 minutes

3 - 4 hours

4 hours

12 months unopened

6 days

26N/mm² at 4 hours 84N/mm² at 28 days

25N/mm² at 24 hours

Standard Grade Rapid Grade

Packaging and Coverage (approx.)


5kg 0.35m² @ 6mm


25kg 1.75m² @ 6mm

RonaFloor Epoxy Floor Mortar Primer 2.25kg 12.5m²

RonaFloor Epoxy Floor Mortar Primer 4.5kg 25m²

Coverage rates are based on smooth, flat, non-porous surfaces

Chemical Resistance Chart



Tap water R 16% Bleach S

Xylene S Animal fats R

50% Sodium Hydroxide

S 10% Lactic Acid S

25% Ammonia S 10% Nitric Acid S

50% Sulphuric Acid

S High Octane Petrol

R

30% Hydrochloric Acid

S Acetone NR

30% Chromic Acid R Engine Oil R

10% Acetic Acid S Methanol S

Skydrol S Toluene S

Teepol 10% R 50% Phosphoric Acid

S

White spirit R 50% Sugar solution

S


The information detailed in this leaflet is liable to modification from time to time in the light of experience and of normal product application, and before using, customers are advised to check with Ronacrete Ltd, quoting the reference number, that they possess the latest issue. Any person or company using the product without first making further enquiries as to the suitability of the product for the intended use does so at his own risk, and Ronacrete Ltd can accept no responsibility for the performance of the product, or for any loss or damage arising out of such use. All goods supplied subject tour Terms and Conditions of Sales; see www.ronacrete.co.uk.



A 3 pack system comprising resin, hardener and aggregate which are supplied in separate containers to be mixed together at the site of application. % By weight CAS No Hazard R-phrases Symbols

Composition of Resin:

Epoxy resin 5-20% 68609-97-2 Xi, N R36/38,43,51/53

Epoxy resin 10-40% 9003-36-5 Xi, N R36/38,43,51/53

Epoxy resin 10-40% 25068-38-6 Xi, N R36/38,43,51/53

Non-toxic additives < 1%

Epoxide derivatives 4-10% Xi, N R36/R38-43,51,53

Combination of high bonding

solvents <1% R37-43,50-53

Composition of Hardener:

Benzyl Alcohol 25-50% 100-51-6 Xn R20,22

Isophoronediamine 10-30% 2855-13-2 C R21,22,34,43

4-Tert-butylphenol <10% 98-54-4 Xi R36,37,38,42,43

Nonylphenol <5 25154-52-3 C, N R22,34,50,53

n-Xylenediamine 10-25% 1477-55-0 C R20/21,31,45

Composition of Aggregate: Natural aggregates, which are produced from naturally occurring rock and gravel deposits and consist of combinations of various minerals including silica. Resin: - Hazard Designation i Irritant N Dangerous to the environment


R36/38 Irritating to eyes and skin R51/53 Toxic to aquatic organisms, may cause long-term adverse

effects in the aquatic environment. R43 May cause sensitisation by skin contact. Contains epoxy constituents. Hardener: - Hazard Designation C Corrosive


R20/21/22 Harmful by inhalation, in contact with skin and if swallowed R34 Causes burns R43 May cause sensitisation by skin contact. Aggregate: Dust inhaled over a prolonged period can be hazardous to health. When the respirable dust contains silica, the risks are increased. Advice on the silica content on individual aggregates is available on request.



Tel: 01279 638700 Fax: 01279 638701

HEALTH AND SAFETY INFORMATION RonaFloor Epoxy Floor Mortar

1. COMPOSITION






Aggregate: Eye Contact: Wash with copious amounts of water and seek medical

advice. Skin Contact: Wash with water. Inhalation: Remove from exposure to a ventilated area. Ingestion: Remove from exposure to a ventilated area. Special hazards: If involved in a fire, may generate noxious or toxic vapours. Protective equipment: Wear full protective suit. Fire fighters wear self-contained breathing apparatus. Extinguishing agents: Foam, dry powder, CO2 or water spray. Aggregate: None needed. Personal precautions: Wear full protective clothing when dealing with a spillage. Keep unprotected persons away. Environmental precautions: Prevent from entering sewer system, surface water, or soil. Methods for cleaning up: Absorb with earth, sand or other absorbent materials.


Aggregate: Personal precautions: In the event of a spillage avoid breathing dust. Wear dust

mask/respirator and goggles as per section 8. Environmental precautions: Releasing the dust into the environment does not constitute

a significant hazard. Methods for cleaning up: Vacuum cleaning, dampen area avoid brushing dry dust

where possible. - Handling: - Information for safe handling.

Ensure good ventilation/exhaustion at the work place. Wear goggles or a face shield, impervious gloves and protective clothing.

- Information about protection against explosion and fires. No special measures required. - Storage: - Requirements to be met by storerooms and containers. Prevent any penetration into the ground. - Further information about storage conditions. Store in cool, dry conditions in well-sealed containers.





Aggregate: The product should be stored in such a way as to reduce airborne dust. When bagged the material should be kept dry and palletised. During application: Wear goggles or a face shield, impervious gloves and

protective clothing. Apply in a well-ventilated area. Aggregate: Occupational exposure levels. Total inhalable dust 10mg/m3 OES Respirable dust 4mg/m3 OES Respirable dust silica 0.3mg/m3 Wear goggles or a face shield, abrasive resistant gloves and protective clothing. Apply in a well-ventilated area. Resin: Physical state: liquid resin. Colour: pale yellow, slightly milky. Odour: weak odour. Vapour pressure: <0.01kPa at 20@C. Boiling point: >200@C. Flash point: >250@C. Density: 1.10 at 20oC. Solubility (water) insoluble. Viscosity: 700cPs at 25oC. Hardener: Physical state: liquid. Colour: pale yellow. Odour: amine-like. Vapour pressure: 0.28mbar at 20oC. Boiling point: >200°C. Flash point: >100@C. Density: 1.05g/cm3 at 20@C. Solubility: slightly soluble. Viscosity: 400cPs at 25oC. Aggregate: Odourless solid particles of crushed stone gravel with

various colours. Chemical properties not applicable. Resin: May react exothermally with amines and mercaptans, also



Aggregate: Not applicable.







Aggregate: May cause transient irritation to eyes. Inhalation of large quantities of respirable silica may lead to progressive lung damage. Chronic exposure to high levels of silica may cause progressive silicosis.

Environmental precautions: Prevent from entering sewer system, surface water or soil. Aggregate: No adverse effect foreseen. DISPOSAL CONSIDERATIONS Waste: Remove according to local authority recommendations, e.g.

Convey to a licensed incinerator. Do not re-use containers.

Aggregate: Non hazardous. Resin: Land Transport ADR/RID (Cross-border) ADR/RID Class: 9 Various dangerous materials and objects. Number/Letter: 11c) Hazard Index Number: 90 Substance Index Number: 3082 Designation of goods: 3082 Maritime transport IMDG IMDG Class: 9 Page: 9082 UN Number: 3082 Packaging group: III EMS Number: - MFAG: - Correct technical name: Environmentally hazardous substance, liquid, n.o.s. (epoxide

derivative) Air transport ICAO-TI and IATA-DGR ICAO/IATA Class: 9 UN/ID Number: 3082 Packaging group: III Correct technical name: Environmentally hazardous substance, liquid, n.o.s. (epoxide

derivative) Transport/Additional Information No dangerous goods according to international transport regulations. Hardener: Land transport ADR/RID (Cross-border) ADR/RID Class: 8 Corrosive materials. Number/Letter: 53c) Hazard index number: 80





Substance index number: 2735 Label: 8 Designation of goods: Polyamines, liquid, corrosive, n.o.s. (isophoronediamine) Maritime transport IMDG IMDG Class 8 Page 8109-2 UN Number: 2735 Packaging group: III MFAG: 320 Marine pollutant: - Correct technical name: Polyamines, liquid, corrosive, n.o.s. (isophoronediamine) Air transport ICAO-TI and IATA-DGR ICAO/IATA Class: 8 UN/ID Number: 2735 Packaging group: III Correct technical name: Polyamines, liquid, corrosive, n.o.s. (isophoronediamine) Aggregate: Non hazardous, no transport labelling required. Resin: Hazard labels: Xi Irritant. N Dangerous for the environment. R-phrases: 51/53 toxic to aquatic organisms. R36/38 Irritating to eyes and skin. R43 May cause sensitisation by skin contact. S-phrases: S26 In case of contact with eyes, rinse immediately with

plenty of water and seek medical advice. S28 After contact with skin, wash immediately with plenty of soap and water.


Hardener: Hazard labels: C Corrosive. R-phrases: R20/21/22 Harmful by inhalation, in contact with skin and if

swallowed. R34/R35 Causes burns. R43 May cause sensitisation by skin contact. S-phrases: S26 In case of contact with eyes, rinse immediately with

plenty of water and seek medical advice. S28 After contact with skin, wash immediately with plenty of soap and water. S36/37/39 Wear suitable protective clothing, gloves and eye/face protection. S45 In case of accident or if you feel unwell, seek medical advice immediately.

Aggregate: Not classified as dangerous for supply within the UK. The above information and advice are given when the material is used as intended. If purchasing on behalf of a third party, it is your duty to take all necessary steps to secure that the person handling or using the material is provided with the information in the data sheet. All the foregoing information should be regarded as being applicable to the finished paint as well as to the individual components.



( Formerly Ronadeck HB100 )


Benefits

High build coating for superior chemical resistance

Can incorporate fine aggregate to achieve slipresistance

Provides decoration; wide colour range

Easy to apply

Low maintenance

Vertical Grade for application to covings and walls



Meets the requirements of FeRFA Classification Type 2and 3

Excellent Abrasion Resistance; mean depth of wear <0.01mm as defined in BS8204:Part 2:1999

Superb adhesion properties to concrete


Royal Mail N.H.S.

Sainsbury’s Eden Project

Carlsberg Brewery Glaxo Smith Kline


The epoxy floor coating shall be RonaFloor HB100 byRonacrete Ltd, tel. +44 (0) 1279 638700. All materials tobe applied in accordance with manufacturers instructions.

Description

RonaFloor HB100 is a solvent free high build epoxy resinfloor coating for use on concrete, screeded and granolithicfloors. It provides excellent abrasion and chemicalresistance for floors subject to constant traffic. Two coatswill provide an easy to clean gloss finish and achieve a dryfilm thickness of 200 microns.

Uses

High performance epoxy coating for floors

Use in factories, warehouses, laboratories, hospitals andshowrooms

Use in areas where chemical resistance and easy cleaningrequired

Internal and external use

Use different colours to identify safety and hazard areas

Also available in Vertical Grade for vertical applications


Site Attendance


Guarantee







Initial Cure Time 6-8 hours

Coverage Rate 25m² per pack per coat

Abrasion Resistance 0.04mm classified as “SpecialClass”*

*Classified as “Special Class” as defined in BS 8204




Application

Preparation

Prepare and test the surface to achieve a structurally soundand clean substrate.

Mixing


Installation

Apply by short nap mohair or lambswool roller directly froma paint tray. Use coverage rates as a guide to thickness;monitor with wet film thickness gauge.

Packaging

RonaFloor HB100 is supplied in 5kg packs.



Health And Safety



Ronacrete Curing MembraneRonaFloor Epoxy DPMRonaFloor Epoxy Floor MortarRonaFloor Epoxy Floor Mortar RapidRonaFloor Concrete DustprooferRonaFloor HB Vertical GradeRonaFloor PU CoatingRonaFloor PU Coating WBRonaFloor Repair 1 Hour 2-6mmRonaFloor Repair 1 Hour 6-50mmRonaFloor Repair 1 Hour 25mm+



Description RonaFloor HB 100 and HB 200 are solvent free high build epoxy floor coatings for use on concrete, screeded and granolithic floors. They provide excellent abrasion and chemical resistance to floors subject to constant traffic. Two coats of RonaFloor HB 100 or HB 200 also provide an easy to clean gloss finish. Cured dry film thickness is between 0.1mm and 0.4mm depending on grade, application rate and number of coats. Grade Selection RonaFloor HB 100 exhibits superior physical and chemical resistance over HB 200. RonaFloor HB 200 should be used where a thicker film build is required. RonaFloor HB Vertical Grade is applied to vertical surfaces only. Rapid Grades Where speed of cure and traffic is important the rapid curing versions of RonaFloor HB resins should be used. RonaFloor HB100 Rapid, HB200 Rapid and HB Vertical Grade Rapid can be foot trafficked after only 4-6 hours (standard grade: 12-24 hours) and by fork truck traffic after 12-24 hours (24-48 hours). The Rapid Grade has a shorter working time and pot life and material must therefore be mixed close to the area of application. The mixed resin must be immediately discharged onto the floor and spread before it begins to cure. Typical Applications RonaFloor HB 100 and HB 200 coatings are used in areas requiring good wear and chemical resistance. They are suitable for use in chemical plant storage areas, warehousing, toilets, laboratories, food preparation areas. They adhere well to concrete, granolithic and polymer floors. Surface Preparation To achieve maximum adhesion it is essential that RonaFloor HB coatings are applied to a structurally sound, clean and dry substrate. Prepare the surface by removing all loose material and making good any structural defects (for fast cure repairs refer to Monoset data sheet). Surfaces must be clean, dry and free from grease, oil, dirt, laitance etc. New concrete, mortar or plaster should be allowed to dry out for up to 28 days prior to coating. RH at the

surface must be below 75% when measured with a Hygrometer, or less than 6% when measured with a Protimeter. It is good practice on such surfaces, new or old, to remove laitance by light mechanical abrasion. The surface should then be vacuum cleaned, washed with clean water and allowed to dry. As with the application of any coating, surfaces should be tested to BS8204 Part 3 1993 to determine its suitability to receive Ronadeck coatings. Application Conditions The workability and ease of application of RonaFloor HB100 and 200 are adversely affected by low temperature; viscosity and curing time will increase. Therefore the material should ideally be stored, mixed and applied at 15°C to 20°C. At lower application temperatures the material should be stored at or warmed to 15°C to 20°C prior to use. Do not use when air and substrate temperature is below 10°C. Surface Sealing When applying to weak or porous concrete it is advisable to seal the prepared surface with Ronadeck Epoxy Floor Mortar Primer, applied at 6-7m² per kg. Mixing Add full contents of hardener container to full contents of resin container and mix with a slow speed drill and spiral mixing paddle until a homogeneous colour is achieved. Typical mixing time is 3-4 minutes. Transfer to a shallow paint tray immediately after mixing to dissipate heat to prolong pot life and extend working time. This is of even greater importance when using Rapid Grade Application Technique Apply by short or medium nap mohair or lambswool (not foam) roller directly from a paint tray. Push the resin well in to the surface making sure the floor is fully wetted and then pull back lightly with the roller to the required thickness. Use coverage rates as a guide to thickness; monitor with wet film thickness gauge. Cleaning Brushes and tools should be cleaned immediately with Ronascreed Cleaning Solvent. Slip Deterrent Surfaces Sprinkle A/S Aggregate onto the first coat whilst wet at the rate of approximately 0.1 to 0.2kg per m² and allow to cure. Brush or vacuum excess A/S Aggregate and apply second coat to achieve desired profile. Coverage rate for RonaFloor HB 100 and 200 on to A/S Aggregate will be considerably reduced. The use of A/S Aggregate will reduce the ease with which the floor can be cleaned. Colours RonaFloor HB coatings are supplied in a range of colours including unpigmented. Refer to colour chart available on request. Maintenance Cleaning Clean the cured surface with Ronadeck Cleaners as required. Use Ronadeck GP Cleaner for oil and grease removal and for general cleaning of the entire surface, and Ronadeck HD Cleaner for heavy localised oil and grease removal. Both are solvent free. See data sheet. Storage and Packaging RonaFloor HB 100 and HB 200 should be stored in unopened containers in dry warehouse conditions between 10°C and 25°C and protected from direct sunlight and frost. Shelf life is approximately 12 months in these conditions. Both RonaFloor HB 100 and 200 are supplied in 5kg packs. Health and Safety First aid - Skin contact, wash immediately with soap and water. Eye contact - wash immediately with copious quantities of water for 10 minutes. Seek immediate medical advice. Ingestion - wash mouth thoroughly with water. Drink water. Do not induce vomiting. Seek immediate medical advice. Spillage - extinguish any ignition sources. Wash small spills away with water, soak large spills with earth or sand; avoid contact; inform authorities of major spillage occurs. Notify Fire Brigade if spillage enters drains.

FEATURES

√ high performance high build epoxy floor coating

√ for chemical resistance, decoration, mechanical wear resistance

√ slip-reducing when used with A/S Aggregate

√ colour range SPECIFICATION CLAUSES 1. Epoxy Floor Coating - Highest Performance The epoxy floor coating shall be RonaFloor HB100 by Ronacrete Ltd, telephone +44 (0) 1279 638700. All materials to be applied in accordance with manufacturers instructions. 2. Epoxy Floor Coating - Medium Performance The epoxy floor coating shall be RonaFloor HB200 by Ronacrete Ltd, telephone +44 (0) 1279 638700. All materials to be applied in accordance with manufacturers instructions.

SUMMARY APPLICATION PROCEDURE RonaFloor HB100 1. prepare surface 2. mix and apply two coats of RonaFloor HB100 3. protect 4. traffic RonaFloor HB200 1. prepare surface 2. mix and apply two coats of RonaFloor HB200 3. protect

RonaFloor HB100, HB200, HB Vertical Grade and Rapid Grade

Medium and high build solvent free epoxy floor coating systems


Coverage rates (based on smooth non-porous surface)

RonaFloor HB 100

1st coat @ 100 microns 25-28m²/5kg

2nd coat @ 100 microns 25-28m²/5kg

RonaFloor HB 200

1st coat @ 200 microns 18-20m2/5kg


1st coat @ 100 - 150 microns 18-20m2/5kg

2nd coat @ 100 - 150 microns 18-20m²/5kg


Technical Data (all at 20oC)

Pot Life 30-45 minutes 10-15 minutes

Initial Cure Time 6-8 hours 4-6 hours

Intercoat Period between 6 and 24 4-6 hours

Foot traffic 12-24 hours 4-6 hours

Fork lift 24-48 hours 12-24 hours

Full chemical cure 7 days 7 days

Compressive Strength (HB 100) 55N/mm² 55N/mm²

Flexural Strength (HB 100) 28N/mm² 28N/mm²


Elastic Modulus (HB 200) ASTM 3.9kN/mm2 3.9kN/mm2

Abrasion Resistance (HB100) 0.04mm classified as “Special Class” as defined in BS

8204

0.04mm classified as “Special Class” as defined in BS

8204

Abrasion Resistance (HB200) 0.01mm classified as “Special Class” as specified in

BS 8204

0.01mm classified as “Special Class” as specified in

BS 8204

Standard grades Rapid Grade Note This product is a carefully formulated blend of resin, hardener and other chemicals, it is designed to be applied as sold. Any on-site dilution, however small, can affect the physical characteristics of the final finish as well as the application properties and curing times. Chemical Resistance Both RonaFloor HB100 and HB200 are resistant to a wide range of chemicals including Skydrol. To achieve optimum performance and appearance in shade and sheen, store and apply material at a constant ambient temperature, humidity and with the same air movement throughout the project. Avoid storage and application at air, substrate and material temperatures below 10oC. RonaFloor HB100 and 200 Packs should be used in strict batch rotation. Individual areas or rooms should be treated with material from a single batch to avoid the inevitable minor variations in shade resulting from batch manufacture, otherwise matched batches should be used to minimise these variations (an extract from FeRFA Guide To The Specification And Application Of Synthetic Resin Flooring). Osmotic blistering In a few cases severe blistering of thin synthetic resin floorings can occur between 3 months and two years after laying. These blisters commonly vary in size from a few mm in diameter up to 100 mm, with heights up to 15 mm. When drilled into or otherwise broken the blisters are found to contain an aqueous liquid under very high pressure. The mechanism of their formation is not fully understood but it is assumed because of their physical state that they are caused by a process of osmosis. Because the mechanism is not fully understood it is not possible to be specific about the steps which should be taken to avoid osmotic blistering. However it is considered good practice to take steps in order to minimise the risk (an extract from FeRFA Guidance Note No 2: Osmosis in Resin Flooring ISBN 0 9538020 5 1). Site Attendance When on site Ronacrete representatives are able, if asked, to give a general indication of the correct method of installing a Ronacrete product. It is important to bear in mind that Ronacrete Ltd is a manufacturer and not an application contractor and it is therefore the responsibility of the contractor and his employer to ensure he is aware of and implements the correct practices and procedures to ensure the correct installation of the product and that liability for its correct installation lies with the contractor and not with Ronacrete Ltd.

SRV Surface Roughness µ Potential for slip

25 and below Below 10 High

25 to 35 10 to 20 Moderate

Slip Resistance— ‘Guidelines recommended by the UK Slip Resistance Group’

35 to 65 20 to 30 Low

Above 65 Above 30 Extremely low

SRV value Dry 70

SRV value Wet 64

Surface roughness 63µ

RonaFloor HB200 with a scatter of AS Aggregate 0.1-0.3mm

SRV value Dry 71

SRV value Wet 62




Chemical Resistant Chart

Chemical RonaFloor HB100 RonaFloor HB200

Tap Water R R

Xylene S S

50% Sodium Hydroxide R R

16% Bleach R R

25% Ammonia R R

50% Sulphuric Acid R R

30% Hydrochloric Acid R R

30% Chromic Acid R R

10% Acetic Acid R R

Skydrol R R

10% Teepol R R

White Spirit R R

50% Sugar Solution R R

50% Phosphoric Acid S S

Animal Fats R R

10% Lactic Acid S S

10% Nitric Acid S S

Petrol R R

Acetone NR NR

Engine Oil R R

Methanol S S

Toluene S S


Citric Acid R R

Industrial Methylated Spirits S S

RONL 132 Issue 8 6 December 2006



RONL 132 Issue 10 29 March 2010


A 2 pack system comprising resin and hardener which are supplied in separate

containers to be mixed together at the site of application.

% By weight CAS No Hazard R-phrases Symbols Composition of Resin: Epoxy resin 5-20% 68609-97-2 Xi, N R36/38,43,51/53 Epoxy resin 10-30% 9003-36-5 Xi, N R36/38,43,51/53 Epoxy resin 10-30% 25068-38-6 Xi, N R36/38,43,51/53 Non-toxic pigments & Additives 40-70% Epoxide derivatives 4-10% Xi, N R36/R38-43,51,53 Combination of high bonding solvents <1% R37-43,50-53

Composition of Hardener: Benzyl Alcohol 25-50% 100-51-6 Xn R20,22 Isophoronediamine 10-30% 2855-13-2 C R21,22,34,43 4-Tert-butylphenol <10% 98-54-4 Xi R36,37,38,42,43 Nonylphenol <5 25154-52-3 C, N R22,34,50,53 n-Xylenediamine 10-25% 1477-55-0 C R20/21,31,45

Resin:

- Hazard Designation

Xi Irritant

N Dangerous to the environment


R36/38 Irritating to eyes and skin.

R51/53 Toxic to aquatic organisms, may cause long-term adverse

effects in the aquatic environment.

R43 May cause sensitisation by skin contact.

Contains epoxy constituents.

Hardener:


C Corrosive


R20/21/22 Harmful by inhalation, in contact with skin and if swallowed.

R34 Causes burns


Eye Contact: Rinse immediately with water, continuing for 15 minutes.

Seek medical attention.

Skin Contact: Rinse immediately with plenty of soap and water.

Remove contaminated clothing.

In case of persistent irritation, or if a rash develops, seek

medical attention.

Ronacrete Limited

Ronac House

Flex Meadow, Merring Way

Harlow, Essex CM19 5TD

Tel: 01279 638700 Fax: 01279 638701

HEALTH AND SAFETY INFORMATION

RonaFloor HB100

1. COMPOSITION



Inhalation: Remove the affected person to fresh air and allow to rest.

In case of breathing difficulty, or distress, seek medical

attention.

Ingestion: Immediately rinse mouth with water and seek medical

attention. If this is not immediately available, drink 1 or 2

pints of water.

Special hazards: If involved in a fire, may generate noxious or toxic vapours.

Protective equipment: Wear full protective suit.

Fire fighters wear self-contained breathing apparatus.

Extinguishing agents: Foam, dry powder, CO2 or water spray.

Personal precautions: Wear full protective clothing when dealing with a spillage.

Keep unprotected persons away.

Environmental precautions: Prevent from entering sewer system, surface water, or soil.

Methods for cleaning up: Absorb with earth, sand or other absorbent materials.

Dispose of contaminated material as waste according to

item 13.

- Handling:

- Information for safe handling.

Ensure good ventilation/exhaustion at the work place.

Wear goggles or a face shield, impervious gloves and protective clothing.

- Information about protection against explosion and fires.

No special measures required.

- Storage:

Requirements to be met by storerooms and containers.

Prevent any penetration into the ground.

- Further information about storage conditions.

Store in cool, dry conditions in well-sealed containers.

During application: Wear goggles or a face shield, impervious gloves and

protective clothing. Apply in a well-ventilated area.

Resin: Physical state: pigment dispersion in liquid resin.

Colour: varies according to shade of finish

required.

Odour: weak odour.

Vapour pressure: <0.01kPa at 20°C.

Boiling point: >200°C.

Flash point: >250°C.

Density: 1.54 at 20oC.

Solubility (water) insoluble.

Viscosity: 2000cPs at 25oC.






Hardener: Physical state: liquid.

Colour: pale yellow.

Odour: amine-like.

Vapour pressure: 0.28mbar at 20oC.



Density: 1.05g/cm3 at 20°C.

Solubility: slightly soluble.


Resin: May react exothermally with amines and mercaptans, also

with acids.

In case of a fire, carbon monoxide, carbon dioxide and other

harmful gases may be formed.

Hardener: Reacts exothermally with acids. Liberates ammonia when

heated. In case of a fire, toxic fumes of nitrogen oxides,

amines and carbon monoxide may be formed. Nitrogen

oxide can react with water vapours to form corrosive nitric

acid.


Epoxy resins such as contained in this product have been

shown to cause irritation in humans on skin and eyes.

Sensitisation by skin contact may also occur.

Hardener: LD50 oral, rat: >1620mg/kg.

The amine/diamine constituents of this product are irritant

to skin and mucous membranes, irritant to eyes, and may

cause sensitisation.

Environmental precautions: Prevent from entering sewer system, surface water or soil.


Waste: Remove according to local authority recommendations, e.g.

Convey to a licensed incinerator.

Do not re-use containers.

Resin:

Land Transport ADR/RID (Cross-border)

ADR/RID Class: 9 Various dangerous materials and

objects.

Number/Letter: 11c)

Hazard Index Number: 90

Substance Index Number: 3082

Designation of goods: 3082






Maritime transport IMDG

IMDG Class: 9

Page: 9082

UN Number: 3082

Packaging group: III

EMS Number: -

MFAG: -

Correct technical name: Environmentally hazardous substance, liquid, n.o.s.

(epoxide derivative)

Air transport ICAO-TI and IATA-DGR

ICAO/IATA Class: 9

UN/ID Number: 3082




Transport/Additional Information No dangerous goods according to international

transport regulations.

Hardener:

Land transport ADR/RID (Cross-border)

ADR/RID Class: 8 Corrosive materials.

Number/Letter: 53c)

Hazard index number: 80

Substance index number: 2735

Label: 8

Designation of goods: Polyamines, liquid,

corrosive, n.o.s. (isophoronediamine)


IMDG Class 8

Page 8109-2

UN Number: 2735


MFAG: 320

Marine pollutant: -

Correct technical name: Polyamines, liquid,



ICAO/IATA Class: 8

UN/ID Number: 2735


Correct technical name: Polyamines, liquid, corrosive, n.o.s. (isophoronediamine)

Resin: Hazard labels: Xi Irritant.

N Dangerous for the environment.

R-phrases: 51/53 toxic to aquatic organisms.



S-phrases: S26 In case of contact with eyes, rinse immediately with

plenty of water and seek

medical advice.

S28 After contact with skin, wash immediately with plenty of

soap and water.

S36 Wear suitable protective clothing.

S61 Avoid release to environment. Refer to special

instructions.


Hardener: Hazard labels: C Corrosive.

R-phrases: R20/21/22 Harmful by inhalation, in contact with skin and if

swallowed.

R34/R35 Causes burns.



plenty of water and seek medical advice.


soap and water.

S36/37/39 Wear suitable protective clothing, gloves and

eye/face protection.

S45 In case of accident or if you feel unwell, seek medical

advice immediately.

The resin and hardener are mixed together in the approximate ratio as follows:

resin: 78-82% by weight

hardener: 18-22% by weight

All the foregoing information should be regarded as being applicable to the finished paint

as well as to the individual resin and hardener components.




% By weight CAS No Hazard R-phrases Symbols Composition of Resin: Epoxy resin 5-20% 68609-97-2 Xi, N R36/38,43,51/53 Epoxy resin 10-30% 9003-36-5 Xi, N R36/38,43,51/53 Epoxy resin 10-30% 25068-38-6 Xi, N R36/38,43,51/53 Non-toxic pigments & Additives 40-70% Epoxide derivatives 4-10% Xi, N R36/R38-43,51,53 Combination of high bonding solvents <1% R37-43,50-53 Composition of Hardener: Benzyl Alcohol 25-50% 100-51-6 Xn R20,22 Isophoronediamine 10-30% 2855-13-2 C R21,22,34,43 4-Tert-butylphenol <10% 98-54-4 Xi R36,37,38,42,43 Nonylphenol <5 25154-52-3 C, N R22,34,50,53 n-Xylenediamine 10-25% 1477-55-0 C R20/21,31,45

Resin:

- Hazard Designation Xi Irritant








Hardener:

- Hazard Designation C Corrosive



R34 Causes burns







medical attention.



attention.

Ronacrete Limited

Ronac House



Tel: 01279 638700 Fax: 01279 638701


RonaFloor HB200

1. COMPOSITION





pints of water.










item 13.

- Handling:






- Storage:

- Requirements to be met by storerooms and containers.








required.

Odour: weak odour.







Hardener: Physical state:


Odour: amine-like.













with acids.







acid.














Resin:


ADR/RID Class: 9 Various dangerous materials

and objects.

Number/Letter: 11c)





IMDG Class: 9

Page: 9082

UN Number: 3082


EMS Number: -

MFAG: -




ICAO/IATA Class: 9

UN/ID Number: 3082









Transport/Additional Information

No dangerous goods according to international transport regulations.

Hardener:



Number/Letter: 53c)



Label: 8

Designation of goods: Polyamines, liquid, corrosive,

n.o.s. (isophoronediamine)


IMDG Class 8

Page 8109-2

UN Number: 2735


MFAG: 320

Marine pollutant: -



ICAO/IATA Class: 8

UN/ID Number: 2735











soap and water.



instructions.



swallowed.






soap and water.




advice immediately.


( Formerly Ronadeck HB100 Rapid )

High build rapid cure epoxy floor coating


Benefits

Rapid cure saves time and money, minimises disruption

High build coating for superior chemical resistance



Easy to apply




Foot traffic after 4 hours, heavy traffic after 12 hours




Royal Mail N.H.S.




The epoxy floor coating shall be RonaFloor HB100 Rapidby Ronacrete Ltd, tel. +44 (0) 1279 638700. All materialsto be applied in accordance with manufacturersinstructions.

Description

RonaFloor HB100 Rapid is a rapid cure solvent free highbuild epoxy resin floor coating for use on concrete,screeded and granolithic floors. It provides excellentabrasion and chemical resistance for floors subject toconstant traffic. Two coats will provide an easy to cleangloss finish and achieve a dry film thickness of 200 microns.

Uses








Site Attendance


Guarantee





Technical Data









Application

Preparation


Mixing


Installation


Packaging

RonaFloor HB100 Rapid is supplied in 5kg packs.



Health And Safety








FEATURES










RonaFloor HB 100



RonaFloor HB 200


















8204


8204


BS 8204


BS 8204






35 to 65 20 to 30 Low


SRV value Dry 70

SRV value Wet 64



SRV value Dry 71

SRV value Wet 62






Tap Water R R

Xylene S S


16% Bleach R R

25% Ammonia R R




10% Acetic Acid R R

Skydrol R R

10% Teepol R R

White Spirit R R



Animal Fats R R

10% Lactic Acid S S

10% Nitric Acid S S

Petrol R R

Acetone NR NR

Engine Oil R R

Methanol S S

Toluene S S


Citric Acid R R











Resin:


Xi Irritant








Hardener:


C Corrosive



R34 Causes burns







medical attention.

Ronacrete Limited

Ronac House



Tel: 01279 638700 Fax: 01279 638701


RonaFloor HB100

1. COMPOSITION





attention.



pints of water.










item 13.

- Handling:






- Storage:









required.

Odour: weak odour.














Odour: amine-like.








with acids.







acid.














Resin:



objects.

Number/Letter: 11c)










IMDG Class: 9

Page: 9082

UN Number: 3082


EMS Number: -

MFAG: -




ICAO/IATA Class: 9

UN/ID Number: 3082






Hardener:



Number/Letter: 53c)



Label: 8




IMDG Class 8

Page 8109-2

UN Number: 2735


MFAG: 320

Marine pollutant: -




ICAO/IATA Class: 8

UN/ID Number: 2735










medical advice.


soap and water.



instructions.




swallowed.






soap and water.




advice immediately.










Resin:









Hardener:




R34 Causes burns







medical attention.



attention.

Ronacrete Limited

Ronac House



Tel: 01279 638700 Fax: 01279 638701


RonaFloor HB200

1. COMPOSITION





pints of water.










item 13.

- Handling:






- Storage:









required.

Odour: weak odour.









Odour: amine-like.













with acids.







acid.














Resin:



and objects.

Number/Letter: 11c)





IMDG Class: 9

Page: 9082

UN Number: 3082


EMS Number: -

MFAG: -




ICAO/IATA Class: 9

UN/ID Number: 3082











Hardener:



Number/Letter: 53c)



Label: 8




IMDG Class 8

Page 8109-2

UN Number: 2735


MFAG: 320

Marine pollutant: -



ICAO/IATA Class: 8

UN/ID Number: 2735











soap and water.



instructions.



swallowed.






soap and water.




advice immediately.


( Formerly Ronadeck HB200 )

High build epoxy floor coating


Benefits

High build coating for superior wear resistance anddurability



Easy to apply

Low maintenance








Royal Mail N.H.S.




The epoxy floor coating shall be RonaFloor HB200 byRonacrete Ltd, tel. +44 (0) 1279 638700. All materials tobe applied in accordance with manufacturers instructions.

Description

RonaFloor HB200 is a solvent free high build epoxy resinfloor coating for use on concrete, screeded and granolithicfloors. It provides excellent abrasion and chemicalresistance for floors subject to constant traffic. Two coatswill provide an easy to clean gloss finish and achieve a dryfilm thickness of 400 microns.

Uses








Site Attendance


Guarantee








Coverage Rate 18 - 20m² per pack per coat






Application

Preparation


Mixing


Installation


Packaging

RonaFloor HB200 is supplied in 5kg packs.



Health And Safety




